ayuzawa/ManageProcess21 · Datasets at Hugging Face

instruction stringlengths 223 3.4k	output stringlengths 206 380	category stringclasses 1 value	fileName null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾘﾆｱｳｴｲ平行調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [ "WEPJ-G002-C06" ] }	{ "QualityItem": "真直度･平行度確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "基準側真直度:両端を0にした状態で中央が+0.025±0.005㎜反基準側平行度:0.010㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾘﾆｱｳｴｲ平行調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾌｫｰｽｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｳｴｲ精度確認", "WorkItems": [ "1. ﾌｫｰｽｹﾞｰｼﾞにて､ﾘﾆｱｶﾞｲﾄﾞｽﾗｲﾀﾞｰの摺動抵抗値を測定する" ], "WorkPoints": [ "各ﾘﾆｱﾌﾞﾛｯｸに対して摺動抵抗測定を実施する※測定速度は50mm/s以下の事1)各ﾌﾞﾛｯｸの摺動抵抗Peak値(動き出し) :規格値4.5N以下2)各ﾌﾞﾛｯｸの摺動抵抗Base値(動作時) :規格値4.0N以下3)各ﾌﾞﾛｯ...	{ "QualityItem": "摺動確認", "ToolManageNo": "-", "ToolCycle": "1回/1年", "ToolRecord": "校正成績書", "StdVal": "Peak値4.5N以下Base値4.0N以下Peak-Base値1.0N以内Baseﾊﾞﾗﾂｷ1.0N以内", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾌｫｰｽｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｳｴｲ精度確認", "WorkItems": [ "1. ﾌｫｰｽｹﾞｰｼﾞにて､ﾘﾆｱｶﾞｲﾄﾞｽﾗｲﾀﾞｰの摺動抵抗値を測定する" ], "WorkPoints": [ "各ﾘﾆｱﾌﾞﾛｯｸに対して摺動抵抗測定を実施する※測定速度は50mm/s以下の事1)各ﾌﾞﾛｯｸの摺動抵抗Peak値(動き出し) :規格値4.5N以下2)各ﾌﾞﾛｯｸの摺動抵抗Base値(動作時) :規格値4.0N以下3)各ﾌﾞﾛｯ...	{ "QualityItem": "摺動確認", "ToolManageNo": "-", "ToolCycle": "1回/1年", "ToolRecord": "校正成績書", "StdVal": "Peak値4.5N以下Base値4.0N以下Peak-Base値1.0N以内Baseﾊﾞﾗﾂｷ1.0N以内", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "1.0N･m", "WorkName": "ｸﾞﾘｰｽｼﾞｮｲﾝﾄ・ｵｲﾙﾊﾟﾝ取付", "WorkItems": [ "1. ①にJOINT を取付ける" ], "WorkPoints": [ "ﾘﾆｱｳｴｲ右端で取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 1.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ｸﾞﾘｰｽｼﾞｮｲﾝﾄ・ｵｲﾙﾊﾟﾝ取付", "WorkItems": [ "2. 1完成品に③をBOLT で取付ける" ], "WorkPoints": [ "下方向に押し当て取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ取付", "WorkItems": [ "1. ①(③)に②(④)をBOLT WASHER で取付ける", "2. 取付け後ﾍｯﾄﾞﾌﾟﾚｰﾄを動作させｵｲﾙﾊﾟﾝと干渉が無い事を確認する" ], "WorkPoints": [ "黄色ﾏｰｶｰ", "隙間無き事", "ﾘﾆｱｳｴｲ右端で取付ける事", "全ｽﾄﾛｰｸにて確認する事", "ｵｲﾙﾊﾟﾝ", ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ取付", "WorkItems": [ "1. ①(③)に②(④)をBOLT WASHER で取付ける", "2. 取付け後ﾍｯﾄﾞﾌﾟﾚｰﾄを動作させｵｲﾙﾊﾟﾝと干渉が無い事を確認する" ], "WorkPoints": [ "黄色ﾏｰｶｰ", "隙間無き事", "ﾘﾆｱｳｴｲ右端で取付ける事", "全ｽﾄﾛｰｸにて確認する事", "ｵｲﾙﾊﾟﾝ", ...	{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.0...	{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "Xﾋﾞｰﾑ組立治具", "Size": "", "ToolOther": "FM-4412", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.03mm...	{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "FM-4412", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾏｸﾞﾈｯﾄｽﾀﾝﾄﾞ取付ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5992", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格...	{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "FM-5992", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "石定盤", "Size": "", "ToolOther": "1500×2000㎜", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.03mm以下"...	{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽﾄﾚｰﾄｴｯｼﾞ", "Size": "1000㎜", "ToolOther": "", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.03mm以下...	{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "ｽﾄﾚｰﾄｴｯｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.03mm以下" ]...	{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "2.5N･m", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WEPJ-G002-C06", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜ﾎﾞｰﾙﾎﾟｲﾝﾄ", "ToolOther": "3.5N･m", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.3", "Size": "", "ToolOther": "FM-2968", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.3㎜止まり0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.4", "Size": "", "ToolOther": "FM-2707", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.3㎜止まり0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.5", "Size": "", "ToolOther": "FM-2969", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.3㎜止まり0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｽｹｰﾙ配線処理", "WorkItems": [ "1. ①の配線を㉖ｲﾝｼｭﾛｯｸで固定する" ], "WorkPoints": [ "配線が穴に被ら無い事", "配線がﾘﾆｱｽｹｰﾙに干渉してい無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作...	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜ﾎﾞｰﾙﾎﾟｲﾝﾄ", "ToolOther": "3.6N･m", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①にBLOCK をBOLT WASHER で取付ける", "2. 1完成品に③をWASHER BOLT で取付ける" ], "WorkPoints": [ "A矢視", "左右はﾈｼﾞ穴中心で取付ける事", "上下は㉘を挟み込み取付ける事", "B矢視", "BLOCK と③の上面を合わせて取...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "6.5㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①にBLOCK をBOLT WASHER で取付ける" ], "WorkPoints": [ "A矢視", "左右はﾈｼﾞ穴中心で取付ける事", "上下は㉘を挟み込み取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m", "締付ﾄﾙｸ 3.6N･m" ], "Inspection...	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "指示通り取付け出来ている事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｹｰﾌﾞﾙﾗﾍﾞﾙ貼付", "WorkItems": [ "1. CABLE のｺﾈｸﾀｰへLABEL のﾗﾍﾞﾙを貼付ける(下図参照の事)" ], "WorkPoints": [ "ｺﾈｸﾀｰの広い側に貼付ける事", "F用ﾍｯﾄﾞ側 (R用は CMRR を貼る)", "F用ｶﾒﾗ側 (R用は B312 を貼る)", "この作業では同じものを2個製作" ], "Tolks": [], "I...	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｹｰﾌﾞﾙﾄﾞｯｷﾝｸﾞ", "WorkItems": [ "1. ①にCABLE or CABLE を㉗で取付ける" ], "WorkPoints": [ "下記指示を参照にﾏｰｷﾝｸﾞして黄色のみ束ねる事", "㉗を束ねる時にコネクターの向きに注意する事", "※CABLE or CABLE は仕様に応じたｹｰﾌﾞﾙを組立する事" ], "Tolks": [], "InspectionNo"...	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線の引き回", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "90cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線①", "WorkItems": [ "1. TUBE TUBE を①のｼﾞｮｲﾝﾄに挿入する", "2. 1完成品にBRACKET をSCREW で固定する", "3. 2完成品を㉙で固定する" ], "WorkPoints": [ "ｸﾞﾘｰｽﾁｭｰﾌﾞの潰れに注意する事", "FANﾓｰﾀｰ線は固定し無い事", "㉙インシュロックの向きに注意する...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "90cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､傷等無き事", "Method": "ｱﾙｶﾝｻｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾍｯﾄﾞﾄﾞﾛﾜ位置決め治具(設備側)", "Size": "", "ToolOther": "FM-5782", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "FM-5782", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "2.5㎜", "ToolOther": "120cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "120cN･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "3. 2完成品にSPACER を取付ける", "2. 1完成品をBOLT WASHER ､WASHER BOLT で取付ける" ], "WorkPoints": [ "SPACER はBOLT 締結後に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m", "締付ﾄﾙｸ 194cN･m", ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "3. 2完成品にSPACER を取付ける", "2. 1完成品をBOLT WASHER ､WASHER BOLT で取付ける" ], "WorkPoints": [ "SPACER はBOLT 締結後に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m", "締付ﾄﾙｸ 194cN･m", ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "6.0N･m", "WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①(②)に③(④)をBOLT WASHER で取付ける" ], "WorkPoints": [ "ｽﾄｯﾊﾟｰがﾋﾞｰﾑに接したときにｹｰﾌﾞﾙとﾌﾞﾗｹｯﾄは1㎜以上ｽｷﾏがある事", "ﾋﾞｰﾑとｽｷﾏ無く､面で接している事", "F側用とR側用に注意して組立する事" ], "Tolks": [ "締付ﾄﾙｸ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①(②)に③(④)をBOLT WASHER で取付ける" ], "WorkPoints": [ "ｽﾄｯﾊﾟｰがﾋﾞｰﾑに接したときにｹｰﾌﾞﾙとﾌﾞﾗｹｯﾄは1㎜以上ｽｷﾏがある事", "ﾋﾞｰﾑとｽｷﾏ無く､面で接している事", "F側用とR側用に注意して組立する事" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･...	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "銘板貼付③", "WorkItems": [ "■◆5. MOTOR 保護ｶﾊﾞｰを取付ける", "■◆2. MOTOR MOTOR に異常が無いか確認する", "■◆3. MOTOR にLABEL を指示寸法で貼付ける", "■◆4. MOTOR にLABEL を指示寸法で貼付ける", "■◆1. MOTOR MOTOR のｼﾘｱﾙNoを確認し､検査表に記入する" ], "WorkPoints": [ "ｼﾘｱ...	{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙ番号転記", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "安全工程", "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "銘板貼付③", "WorkItems": [ "■◆5. MOTOR 保護ｶﾊﾞｰを取付ける", "■◆2. MOTOR MOTOR に異常が無いか確認する", "■◆3. MOTOR にLABEL を指示寸法で貼付ける", "■◆4. MOTOR にLABEL を指示寸法で貼付ける", "■◆1. MOTOR MOTOR のｼﾘｱﾙNoを確認し､検査表に記入する" ], "WorkPoints": [ "ｼﾘｱ...	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "安全工程", "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "銘板貼付③", "WorkItems": [ "■◆5. MOTOR 保護ｶﾊﾞｰを取付ける", "■◆2. MOTOR MOTOR に異常が無いか確認する", "■◆3. MOTOR にLABEL を指示寸法で貼付ける", "■◆4. MOTOR にLABEL を指示寸法で貼付ける", "■◆1. MOTOR MOTOR のｼﾘｱﾙNoを確認し､検査表に記入する" ], "WorkPoints": [ "...	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程", "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "固定子取付-①", "WorkItems": [ "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆1. ①(②)の右側に③をBOLT で取付ける" ], "WorkPoints": [ "③左右はﾈｼﾞ穴ｾﾝﾀｰで取付ける事", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程", "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.2", "Size": "", "ToolOther": "FM-4645", "WorkName": "固定子取付-①", "WorkItems": [ "■◆3. 固定子半保護ｶﾊﾞｰを右側固定子に取付ける", "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆1. ①(②)の右側に③をBOLT で取付ける" ], "WorkPoints": [ "③左右はﾈｼﾞ穴ｾﾝﾀｰで取付ける事", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事...	{ "QualityItem": "取付確認", "ToolManageNo": "FM-4645", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "安全工程", "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.6", "Size": "", "ToolOther": "FM-4646", "WorkName": "固定子取付-①", "WorkItems": [ "■◆3. 固定子半保護ｶﾊﾞｰを右側固定子に取付ける", "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆1. ①(②)の右側に③をBOLT で取付ける" ], "WorkPoints": [ "③左右はﾈｼﾞ穴ｾﾝﾀｰで取付ける事", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事...	{ "QualityItem": "取付確認", "ToolManageNo": "FM-4646", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }	information_extraction	null
{ "ToolName": "X軸固定子半保護ｶﾊﾞｰ", "Size": "", "ToolOther": "FM-6166", "WorkName": "固定子取付-①", "WorkItems": [ "■◆3. 固定子半保護ｶﾊﾞｰを右側固定子に取付ける" ], "WorkPoints": [ "①②の可動子を移動させて③の全域を確認する事", "③固定子の磁力に注意して可動子を右側に移動させる", "③固定子の左側に㉚を取付ける", "各ｹｰﾌﾞﾙの挟み込み､④固定子の傷に十分注意して作業を行う事" ], "Tolks"...	{ "QualityItem": "取付確認", "ToolManageNo": "FM-6166", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "固定子取付-②", "WorkItems": [ "■◆1. ①(②)の左側に③をBOLT で取付ける" ], "WorkPoints": [ "固定子同士が強烈に吸引される為､指等の挟まれに注意する事(特に緑色線部)", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事", "①②可動子のヘッドブラケットを中心で㉛を取付ける事", "作業終了後に㉚固定子半保護カバーを取...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程", "安全工程" ] }	information_extraction	null
{ "ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.2", "Size": "0.2㎜", "ToolOther": "FM-4645", "WorkName": "固定子取付-②", "WorkItems": [ "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆3. 固定子に保護ｶﾊﾞｰを取付ける" ], "WorkPoints": [ "①②の可動子を移動させて③の全域を㉘㉙で確認する事", "通り0.1mm､止まり0.6mm" ], "Tolks": [], "InspectionNo": "WEPJ-...	{ "QualityItem": "取付確認", "ToolManageNo": "FM-4645", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.1㎜止まり0.6㎜", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "安全工程", "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.6", "Size": "0.6㎜", "ToolOther": "FM-4646", "WorkName": "固定子取付-②", "WorkItems": [ "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆3. 固定子に保護ｶﾊﾞｰを取付ける" ], "WorkPoints": [ "①②の可動子を移動させて③の全域を㉘㉙で確認する事", "通り0.1mm､止まり0.6mm" ], "Tolks": [], "InspectionNo": "WEPJ-...	{ "QualityItem": "取付確認", "ToolManageNo": "FM-4646", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.1㎜止まり0.6㎜", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }	information_extraction	null
{ "ToolName": "X軸固定子半保護ｶﾊﾞｰ", "Size": "", "ToolOther": "FM-6166", "WorkName": "固定子取付-②", "WorkItems": [ "■◆1. ①(②)の左側に③をBOLT で取付ける" ], "WorkPoints": [ "固定子同士が強烈に吸引される為､指等の挟まれに注意する事(特に緑色線部)", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事", "①②可動子のヘッドブラケットを中心で㉛を取付ける事", "作業終了後に㉚固定子半保護...	{ "QualityItem": "取付確認", "ToolManageNo": "FM-6166", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }	information_extraction	null
{ "ToolName": "X軸固定子簡易保護ｶﾊﾞｰ", "Size": "", "ToolOther": "FM-5973", "WorkName": "固定子取付-②", "WorkItems": [ "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆3. 固定子に保護ｶﾊﾞｰを取付ける" ], "WorkPoints": [ "①②の可動子を移動させて③の全域を㉘㉙で確認する事", "通り0.1mm､止まり0.6mm" ], "Tolks": [], "InspectionNo": "", "Inspe...	{ "QualityItem": "取付確認", "ToolManageNo": "FM-5973", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｽﾄｯﾊﾟｰ(F,R)・干渉ｾﾝｻｰ(Rのみ)取付", "WorkItems": [ "1. SCREW にNUT を挿入する", "2. ①に1完成品とSTOPPER を取付ける", "3. 2完成品にSENSOR をBOLT WASHER WASHER で取付ける", "1. SCREW にNUT を挿入する", "2. ①に1完成品とSTOPPER を取付ける", "3. 2完成品にSENSOR をBOL...	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "19㎜", "ToolOther": "6.0N･m", "WorkName": "ｽﾄｯﾊﾟｰ(F,R)・干渉ｾﾝｻｰ(Rのみ)取付", "WorkItems": [ "1. SCREW にNUT を挿入する", "2. ①に1完成品とSTOPPER を取付ける", "3. 2完成品にSENSOR をBOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "出代:37.5㎜を確認し取付ける事", "※K052-2(R側)のみ" ], ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "40cN･m", "WorkName": "ｽﾄｯﾊﾟｰ(F,R)・干渉ｾﾝｻｰ(Rのみ)取付", "WorkItems": [ "1. SCREW にNUT を挿入する", "2. ①に1完成品とSTOPPER を取付ける", "3. 2完成品にSENSOR をBOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "出代:37.5㎜を確認し取付ける事", "※K052-2(R側)のみ" ]...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "40cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾕﾆｯﾄ銘板貼付", "WorkItems": [ "2. ①②に③を貼付ける", "1. ①②の貼付け面を脱脂する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し1", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ "V±aK301", "COM6a", "±aK3010.09/10/11", "101.02/03", ":ｽﾀｰﾄ :ｺﾞｰﾙ", "HDP", "A1bK201", "-VaT1022aF123", ...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し2", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "1aF121/2", "+V1/2aT101" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], ...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し3", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "1K301P", "EX212", "2bF125" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes"...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し4", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "AX212", "2a/bF122", "-VbT101" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTyp...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し5", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "AX211", "2a/bF121", "-XV1/2aT101" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "Wor...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し6", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1. CABLE を引き回す", ":ｽﾀｰﾄ :ｺﾞｰﾙ", "A1K101T33K101", "CX...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し7", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "BX211", "1/3aK201" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Wor...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し8", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "CX211", "1/2/3/5_PWK601", "2aK202" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "Wo...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し9", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "DX211", "1/2/3/5_PWK602", "4aK202" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "Wo...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し10", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "FX212", "CN1K304", "CN7K303" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTyp...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し11", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "S001P", "21aK201", "T32K101", "2aF125", "BX212", "1aF125" ], "Tolks": [], "InspectionNo...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し12", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "1S301P", "*S201", "DX212", "T11/12K101", "T21/22K101", "6aK202", "0.00/0.01" ], "Tolk...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し13", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "CN1K603", "2aF124", "EX211" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkType...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し14", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "T31K101", "22aK202" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "W...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し15", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "5aK201" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し16", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "A1aK202", "S24K101" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "W...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し17", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "A1aK201", "S14K101" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "W...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し18", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "A2bK201", "A2aK202" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "W...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し19", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "1aF123", "+VaT102" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Wo...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し20", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ ":ｽﾀｰﾄ :ｺﾞｰﾙ", "COM6b", "COM7a" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words...	{ "QualityItem": "引き回確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り引き回出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引結束", "WorkItems": [ "1. 引き回したﾊｰﾈｽをｲﾝｼｭﾛｯｸで固定する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", ...	{ "QualityItem": "結束確認", "ToolManageNo": "FM-6061", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り結束出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｱﾘﾝｸﾞ部組立", "WorkItems": [ "2. BRACKET にCAM-FOLLOWER を通しWASHER WASHER NUT の順で取付け｡" ], "WorkPoints": [ "･左右2ヶ組立てる", "NUT ﾅｯﾄの丸みのある方を外側にする" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "Inspection...	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "5.5㎜", "ToolOther": "150cN･m", "WorkName": "ﾍﾞｱﾘﾝｸﾞ部組立", "WorkItems": [ "2. BRACKET にCAM-FOLLOWER を通しWASHER WASHER NUT の順で取付け｡" ], "WorkPoints": [ "･左右2ヶ組立てる", "NUT ﾅｯﾄの丸みのある方を外側にする" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cNm±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "150㎜", "WorkName": "右ﾚﾊﾞｰ部組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｴｯｼﾞが立ていないこと", "BOLT ", "NUT ", "出代9㎜", "･締付けﾄﾙｸ : 100cN･m", ...	{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:9㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "100cN･m", "WorkName": "右ﾚﾊﾞｰ部組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｴｯｼﾞが立ていないこと", "BOLT ", "NUT ", "出代9㎜", "･締付けﾄﾙｸ : 100...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "150㎜", "WorkName": "左ﾚﾊﾞｰ部組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "BOLT ", "NUT ", "出代9㎜", "2.LEVER にBOLT NUT を取付ける｡", "･(注意) 折り曲...	{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:9㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "100cN･m", "WorkName": "左ﾚﾊﾞｰ部組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "BOLT ", "NUT ", "出代9㎜", "2.LEVER にBOLT NUT を取付ける｡", "･...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｸﾞﾘｰｽ塗布", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左右ﾚﾊﾞｰ部組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "COLLAR ", "NUT ", "BRACKET ", "PIN P001", "COLLAR...	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "5N･m", "WorkName": "左右ﾚﾊﾞｰ部組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "COLLAR ", "NUT ", "BRACKET ", "PIN P001", ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "5Nm±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "BOLT取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "", "WorkName": "BOLT取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "90cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "下受けﾌﾟﾚｰﾄﾛｰﾗｰ位置決め治具", "Size": "", "ToolOther": "FM-3253FM-4715", "WorkName": "ﾌﾞﾛｯｸ取付け①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "FM-3253FM-4715", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "検査書通りの事", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "ﾌﾞﾛｯｸ取付け①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "WEBS-F013-011" ] }	{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間0.02㎜", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WEBS-F013-011", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "2.5㎜", "ToolOther": "2.5N･m", "WorkName": "ﾌﾞﾛｯｸ取付け①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "下受けﾌﾟﾚｰﾄﾛｰﾗｰ位置決め治具", "Size": "", "ToolOther": "FM-3253FM-4715", "WorkName": "ﾌﾞﾛｯｸ取付け②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "FM-3253FM-4715", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "検査書通りの事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "ﾌﾞﾛｯｸ取付け②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "WEBS-F013-011" ] }	{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間0.02㎜", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WEBS-F013-011", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "", "WorkName": "ﾌﾞﾛｯｸ取付け②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "1.0㎜", "ToolOther": "", "WorkName": "左右ﾚﾊﾞｰ取付け", "WorkItems": [ "4. ﾌﾟﾚｰﾄを表面にし左側のﾚﾊﾞｰに⑩S/Nｼｰﾙを貼る｡" ], "WorkPoints": [ "広がったﾌﾟﾚｰﾄとｱｰﾑの隙間にﾌﾞﾛｯｸｹﾞｰｼﾞ1mmを挟み､もう一方のﾋﾞｽを締める｡", "ﾌﾟﾚｰﾄとｱｰﾑの干渉が無い事を確認できたらﾋﾞｽを増締めする｡(ﾚﾊﾞｰとﾌﾟﾚｰﾄの隙間確認)" ], "Tolks": [], ...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間1.0㎜", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "2.5㎜", "ToolOther": "2.5N･m", "WorkName": "左右ﾚﾊﾞｰ取付け", "WorkItems": [ "4. ﾌﾟﾚｰﾄを表面にし左側のﾚﾊﾞｰに⑩S/Nｼｰﾙを貼る｡" ], "WorkPoints": [ "広がったﾌﾟﾚｰﾄとｱｰﾑの隙間にﾌﾞﾛｯｸｹﾞｰｼﾞ1mmを挟み､もう一方のﾋﾞｽを締める｡", "ﾌﾟﾚｰﾄとｱｰﾑの干渉が無い事を確認できたらﾋﾞｽを増締めする｡(ﾚﾊﾞｰとﾌﾟﾚｰﾄの隙間確認)" ], "Tolks": [], ...	{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "高さ平面度測定治具てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "", "ToolOther": "-FM-5001", "WorkName": "ﾌﾟﾚｰﾄ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "WEBS-F013-011" ] }	{ "QualityItem": "平面度", "ToolManageNo": "-FM-5001", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "-0.18㎜~+0.13㎜", "Method": "高さ平面度測定治具てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEBS-F013-011", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ(0.1/0.3/0,5㎜))", "Size": "", "ToolOther": "", "WorkName": "ﾌﾟﾚｰﾄ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "WEBS-F013-011" ] }	{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.1㎜止まり0.3㎜ﾎﾞﾙﾄ・ﾌﾟﾚｰﾄ間:0.5㎜以上", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ(0.1/0.3/0,5㎜)", "RecordMethod": "WEBS-F013-011", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "", "WorkName": "ﾌﾟﾚｰﾄ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }	{ "QualityItem": "締結ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "90cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ調整ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5858", "WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄに㉗-１を仮取付けする", "3. 高さ調整治具位置出しを行う", "4. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄの位置決めﾋﾟﾝを㉗-1に押し当て締結する", "4. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄの位置決めﾋﾟﾝを㉗-1に押し当て締結する" ], "WorkPoints": [ "㉗-1をﾍｯﾄﾞ取...	{ "QualityItem": "取付確認", "ToolManageNo": "FM-5858", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "1.9N･m", "WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整", "WorkItems": [ "4. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄの位置決めﾋﾟﾝを㉗-1に押し当て締結する" ], "WorkPoints": [ "X軸及びY軸を移動し㉗-1を㉗-2の上に移動", "㉗-1の仮止めﾋﾞｽを緩め㉗の1を㉗-2に当付けﾋﾞｽを締結する" ], "Tolks": [], "InspectionNo": "", "Inspecti...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.9N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.03㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整", "WorkItems": [ "4. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄの位置決めﾋﾟﾝを㉗-1に押し当て締結する" ], "WorkPoints": [ "X軸及びY軸を移動し㉗-1を㉗-2の上に移動", "㉗-1の仮止めﾋﾞｽを緩め㉗の1を㉗-2に当付けﾋﾞｽを締結する" ], "Tolks": [], "InspectionNo": "", "Inspect...	{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾍｯﾄﾞｶﾒﾗ取付け(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)", "WorkItems": [ "■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する", "2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける" ], "WorkPoints": [ "ｼﾘｱﾙNo.記載位置", "規正ﾋﾟﾝ穴"...	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞｶﾒﾗ取付け(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)", "WorkItems": [ "■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する", "2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける" ], "WorkPoints": [ "ｼﾘｱﾙNo.記載位置", "規正ﾋﾟﾝ穴", "規正ﾋﾟﾝ...	{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WEPJ-G002-D08", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞｶﾒﾗ取付け(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)", "WorkItems": [ "■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する", "2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける" ], "WorkPoints": [ "ｼﾘｱﾙNo.記載位置", "規正ﾋﾟﾝ穴", "規正ﾋﾟﾝ...	{ "QualityItem": "製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "製造番号転記", "Method": "目視", "RecordMethod": "WEPJ-G002-D08", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null

{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾘﾆｱｳｴｲ平行調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [ "WEPJ-G002-C06" ] }

{ "QualityItem": "真直度･平行度確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "基準側真直度:両端を0にした状態で中央が+0.025±0.005㎜反基準側平行度:0.010㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾘﾆｱｳｴｲ平行調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾌｫｰｽｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｳｴｲ精度確認", "WorkItems": [ "1. ﾌｫｰｽｹﾞｰｼﾞにて､ﾘﾆｱｶﾞｲﾄﾞｽﾗｲﾀﾞｰの摺動抵抗値を測定する" ], "WorkPoints": [ "各ﾘﾆｱﾌﾞﾛｯｸに対して摺動抵抗測定を実施する※測定速度は50mm/s以下の事1)各ﾌﾞﾛｯｸの摺動抵抗Peak値(動き出し) :規格値4.5N以下2)各ﾌﾞﾛｯｸの摺動抵抗Base値(動作時) :規格値4.0N以下3)各ﾌﾞﾛｯ...

{ "QualityItem": "摺動確認", "ToolManageNo": "-", "ToolCycle": "1回/1年", "ToolRecord": "校正成績書", "StdVal": "Peak値4.5N以下Base値4.0N以下Peak-Base値1.0N以内Baseﾊﾞﾗﾂｷ1.0N以内", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾌｫｰｽｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｳｴｲ精度確認", "WorkItems": [ "1. ﾌｫｰｽｹﾞｰｼﾞにて､ﾘﾆｱｶﾞｲﾄﾞｽﾗｲﾀﾞｰの摺動抵抗値を測定する" ], "WorkPoints": [ "各ﾘﾆｱﾌﾞﾛｯｸに対して摺動抵抗測定を実施する※測定速度は50mm/s以下の事1)各ﾌﾞﾛｯｸの摺動抵抗Peak値(動き出し) :規格値4.5N以下2)各ﾌﾞﾛｯｸの摺動抵抗Base値(動作時) :規格値4.0N以下3)各ﾌﾞﾛｯ...

{ "QualityItem": "摺動確認", "ToolManageNo": "-", "ToolCycle": "1回/1年", "ToolRecord": "校正成績書", "StdVal": "Peak値4.5N以下Base値4.0N以下Peak-Base値1.0N以内Baseﾊﾞﾗﾂｷ1.0N以内", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "1.0N･m", "WorkName": "ｸﾞﾘｰｽｼﾞｮｲﾝﾄ・ｵｲﾙﾊﾟﾝ取付", "WorkItems": [ "1. ①にJOINT を取付ける" ], "WorkPoints": [ "ﾘﾆｱｳｴｲ右端で取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 1.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ｸﾞﾘｰｽｼﾞｮｲﾝﾄ・ｵｲﾙﾊﾟﾝ取付", "WorkItems": [ "2. 1完成品に③をBOLT で取付ける" ], "WorkPoints": [ "下方向に押し当て取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ ...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ取付", "WorkItems": [ "1. ①(③)に②(④)をBOLT WASHER で取付ける", "2. 取付け後ﾍｯﾄﾞﾌﾟﾚｰﾄを動作させｵｲﾙﾊﾟﾝと干渉が無い事を確認する" ], "WorkPoints": [ "黄色ﾏｰｶｰ", "隙間無き事", "ﾘﾆｱｳｴｲ右端で取付ける事", "全ｽﾄﾛｰｸにて確認する事", "ｵｲﾙﾊﾟﾝ", ...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ取付", "WorkItems": [ "1. ①(③)に②(④)をBOLT WASHER で取付ける", "2. 取付け後ﾍｯﾄﾞﾌﾟﾚｰﾄを動作させｵｲﾙﾊﾟﾝと干渉が無い事を確認する" ], "WorkPoints": [ "黄色ﾏｰｶｰ", "隙間無き事", "ﾘﾆｱｳｴｲ右端で取付ける事", "全ｽﾄﾛｰｸにて確認する事", "ｵｲﾙﾊﾟﾝ", ...

{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.0...

{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "Xﾋﾞｰﾑ組立治具", "Size": "", "ToolOther": "FM-4412", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.03mm...

{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "FM-4412", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾏｸﾞﾈｯﾄｽﾀﾝﾄﾞ取付ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5992", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格...

{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "FM-5992", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "石定盤", "Size": "", "ToolOther": "1500×2000㎜", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.03mm以下"...

{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽﾄﾚｰﾄｴｯｼﾞ", "Size": "1000㎜", "ToolOther": "", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.03mm以下...

{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "ｽﾄﾚｰﾄｴｯｼﾞ", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "Y・Z方向変位測定", "WorkItems": [ "2. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､94㎜STのZ方向変位を測定する", "1. ﾍｯﾄﾞﾌﾟﾚｰﾄを移動し､全STのZ方向変位を測定する" ], "WorkPoints": [ "規格値:0.01mm以下", "ﾍｯﾄﾞﾌﾟﾚｰﾄより69㎜の位置でZ方向の変位を測定する", "規格値:0.03mm以下", "規格値:0.03mm以下" ]...

{ "QualityItem": "Z方向Y方向変位確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "2.5N･m", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WEPJ-G002-C06", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜ﾎﾞｰﾙﾎﾟｲﾝﾄ", "ToolOther": "3.5N･m", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.3", "Size": "", "ToolOther": "FM-2968", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.3㎜止まり0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.4", "Size": "", "ToolOther": "FM-2707", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.3㎜止まり0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.5", "Size": "", "ToolOther": "FM-2969", "WorkName": "ﾘﾆｱｽｹｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.3㎜止まり0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｽｹｰﾙ配線処理", "WorkItems": [ "1. ①の配線を㉖ｲﾝｼｭﾛｯｸで固定する" ], "WorkPoints": [ "配線が穴に被ら無い事", "配線がﾘﾆｱｽｹｰﾙに干渉してい無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作...

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜ﾎﾞｰﾙﾎﾟｲﾝﾄ", "ToolOther": "3.6N･m", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①にBLOCK をBOLT WASHER で取付ける", "2. 1完成品に③をWASHER BOLT で取付ける" ], "WorkPoints": [ "A矢視", "左右はﾈｼﾞ穴中心で取付ける事", "上下は㉘を挟み込み取付ける事", "B矢視", "BLOCK と③の上面を合わせて取...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "6.5㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①にBLOCK をBOLT WASHER で取付ける" ], "WorkPoints": [ "A矢視", "左右はﾈｼﾞ穴中心で取付ける事", "上下は㉘を挟み込み取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m", "締付ﾄﾙｸ 3.6N･m" ], "Inspection...

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "指示通り取付け出来ている事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｹｰﾌﾞﾙﾗﾍﾞﾙ貼付", "WorkItems": [ "1. CABLE のｺﾈｸﾀｰへLABEL のﾗﾍﾞﾙを貼付ける(下図参照の事)" ], "WorkPoints": [ "ｺﾈｸﾀｰの広い側に貼付ける事", "F用ﾍｯﾄﾞ側 (R用は CMRR を貼る)", "F用ｶﾒﾗ側 (R用は B312 を貼る)", "この作業では同じものを2個製作" ], "Tolks": [], "I...

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｹｰﾌﾞﾙﾄﾞｯｷﾝｸﾞ", "WorkItems": [ "1. ①にCABLE or CABLE を㉗で取付ける" ], "WorkPoints": [ "下記指示を参照にﾏｰｷﾝｸﾞして黄色のみ束ねる事", "㉗を束ねる時にコネクターの向きに注意する事", "※CABLE or CABLE は仕様に応じたｹｰﾌﾞﾙを組立する事" ], "Tolks": [], "InspectionNo"...

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線の引き回", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "90cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線①", "WorkItems": [ "1. TUBE TUBE を①のｼﾞｮｲﾝﾄに挿入する", "2. 1完成品にBRACKET をSCREW で固定する", "3. 2完成品を㉙で固定する" ], "WorkPoints": [ "ｸﾞﾘｰｽﾁｭｰﾌﾞの潰れに注意する事", "FANﾓｰﾀｰ線は固定し無い事", "㉙インシュロックの向きに注意する...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "90cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､傷等無き事", "Method": "ｱﾙｶﾝｻｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾍｯﾄﾞﾄﾞﾛﾜ位置決め治具(設備側)", "Size": "", "ToolOther": "FM-5782", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "FM-5782", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "2.5㎜", "ToolOther": "120cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "120cN･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "3. 2完成品にSPACER を取付ける", "2. 1完成品をBOLT WASHER ､WASHER BOLT で取付ける" ], "WorkPoints": [ "SPACER はBOLT 締結後に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m", "締付ﾄﾙｸ 194cN･m", ...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "3. 2完成品にSPACER を取付ける", "2. 1完成品をBOLT WASHER ､WASHER BOLT で取付ける" ], "WorkPoints": [ "SPACER はBOLT 締結後に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m", "締付ﾄﾙｸ 194cN･m", ...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "6.0N･m", "WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①(②)に③(④)をBOLT WASHER で取付ける" ], "WorkPoints": [ "ｽﾄｯﾊﾟｰがﾋﾞｰﾑに接したときにｹｰﾌﾞﾙとﾌﾞﾗｹｯﾄは1㎜以上ｽｷﾏがある事", "ﾋﾞｰﾑとｽｷﾏ無く､面で接している事", "F側用とR側用に注意して組立する事" ], "Tolks": [ "締付ﾄﾙｸ...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①(②)に③(④)をBOLT WASHER で取付ける" ], "WorkPoints": [ "ｽﾄｯﾊﾟｰがﾋﾞｰﾑに接したときにｹｰﾌﾞﾙとﾌﾞﾗｹｯﾄは1㎜以上ｽｷﾏがある事", "ﾋﾞｰﾑとｽｷﾏ無く､面で接している事", "F側用とR側用に注意して組立する事" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･...

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "銘板貼付③", "WorkItems": [ "■◆5. MOTOR 保護ｶﾊﾞｰを取付ける", "■◆2. MOTOR MOTOR に異常が無いか確認する", "■◆3. MOTOR にLABEL を指示寸法で貼付ける", "■◆4. MOTOR にLABEL を指示寸法で貼付ける", "■◆1. MOTOR MOTOR のｼﾘｱﾙNoを確認し､検査表に記入する" ], "WorkPoints": [ "ｼﾘｱ...

{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙ番号転記", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "-", "ProcessNames": [ "安全工程", "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "銘板貼付③", "WorkItems": [ "■◆5. MOTOR 保護ｶﾊﾞｰを取付ける", "■◆2. MOTOR MOTOR に異常が無いか確認する", "■◆3. MOTOR にLABEL を指示寸法で貼付ける", "■◆4. MOTOR にLABEL を指示寸法で貼付ける", "■◆1. MOTOR MOTOR のｼﾘｱﾙNoを確認し､検査表に記入する" ], "WorkPoints": [ "ｼﾘｱ...

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "安全工程", "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "銘板貼付③", "WorkItems": [ "■◆5. MOTOR 保護ｶﾊﾞｰを取付ける", "■◆2. MOTOR MOTOR に異常が無いか確認する", "■◆3. MOTOR にLABEL を指示寸法で貼付ける", "■◆4. MOTOR にLABEL を指示寸法で貼付ける", "■◆1. MOTOR MOTOR のｼﾘｱﾙNoを確認し､検査表に記入する" ], "WorkPoints": [ "...

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程", "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "固定子取付-①", "WorkItems": [ "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆1. ①(②)の右側に③をBOLT で取付ける" ], "WorkPoints": [ "③左右はﾈｼﾞ穴ｾﾝﾀｰで取付ける事", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程", "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.2", "Size": "", "ToolOther": "FM-4645", "WorkName": "固定子取付-①", "WorkItems": [ "■◆3. 固定子半保護ｶﾊﾞｰを右側固定子に取付ける", "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆1. ①(②)の右側に③をBOLT で取付ける" ], "WorkPoints": [ "③左右はﾈｼﾞ穴ｾﾝﾀｰで取付ける事", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事...

{ "QualityItem": "取付確認", "ToolManageNo": "FM-4645", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "安全工程", "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.6", "Size": "", "ToolOther": "FM-4646", "WorkName": "固定子取付-①", "WorkItems": [ "■◆3. 固定子半保護ｶﾊﾞｰを右側固定子に取付ける", "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆1. ①(②)の右側に③をBOLT で取付ける" ], "WorkPoints": [ "③左右はﾈｼﾞ穴ｾﾝﾀｰで取付ける事", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事...

{ "QualityItem": "取付確認", "ToolManageNo": "FM-4646", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }

information_extraction

0

null

{ "ToolName": "X軸固定子半保護ｶﾊﾞｰ", "Size": "", "ToolOther": "FM-6166", "WorkName": "固定子取付-①", "WorkItems": [ "■◆3. 固定子半保護ｶﾊﾞｰを右側固定子に取付ける" ], "WorkPoints": [ "①②の可動子を移動させて③の全域を確認する事", "③固定子の磁力に注意して可動子を右側に移動させる", "③固定子の左側に㉚を取付ける", "各ｹｰﾌﾞﾙの挟み込み､④固定子の傷に十分注意して作業を行う事" ], "Tolks"...

{ "QualityItem": "取付確認", "ToolManageNo": "FM-6166", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "固定子取付-②", "WorkItems": [ "■◆1. ①(②)の左側に③をBOLT で取付ける" ], "WorkPoints": [ "固定子同士が強烈に吸引される為､指等の挟まれに注意する事(特に緑色線部)", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事", "①②可動子のヘッドブラケットを中心で㉛を取付ける事", "作業終了後に㉚固定子半保護カバーを取...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程", "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.2", "Size": "0.2㎜", "ToolOther": "FM-4645", "WorkName": "固定子取付-②", "WorkItems": [ "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆3. 固定子に保護ｶﾊﾞｰを取付ける" ], "WorkPoints": [ "①②の可動子を移動させて③の全域を㉘㉙で確認する事", "通り0.1mm､止まり0.6mm" ], "Tolks": [], "InspectionNo": "WEPJ-...

{ "QualityItem": "取付確認", "ToolManageNo": "FM-4645", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.1㎜止まり0.6㎜", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "安全工程", "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.6", "Size": "0.6㎜", "ToolOther": "FM-4646", "WorkName": "固定子取付-②", "WorkItems": [ "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆3. 固定子に保護ｶﾊﾞｰを取付ける" ], "WorkPoints": [ "①②の可動子を移動させて③の全域を㉘㉙で確認する事", "通り0.1mm､止まり0.6mm" ], "Tolks": [], "InspectionNo": "WEPJ-...

{ "QualityItem": "取付確認", "ToolManageNo": "FM-4646", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "通り0.1㎜止まり0.6㎜", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }

information_extraction

0

null

{ "ToolName": "X軸固定子半保護ｶﾊﾞｰ", "Size": "", "ToolOther": "FM-6166", "WorkName": "固定子取付-②", "WorkItems": [ "■◆1. ①(②)の左側に③をBOLT で取付ける" ], "WorkPoints": [ "固定子同士が強烈に吸引される為､指等の挟まれに注意する事(特に緑色線部)", "③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上､｢S極｣ﾗﾍﾞﾙを左下(+移動方向)にする事", "①②可動子のヘッドブラケットを中心で㉛を取付ける事", "作業終了後に㉚固定子半保護...

{ "QualityItem": "取付確認", "ToolManageNo": "FM-6166", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }

information_extraction

0

null

{ "ToolName": "X軸固定子簡易保護ｶﾊﾞｰ", "Size": "", "ToolOther": "FM-5973", "WorkName": "固定子取付-②", "WorkItems": [ "■◆2. 1完成品の固定子と可動子のGAPを確認する", "■◆3. 固定子に保護ｶﾊﾞｰを取付ける" ], "WorkPoints": [ "①②の可動子を移動させて③の全域を㉘㉙で確認する事", "通り0.1mm､止まり0.6mm" ], "Tolks": [], "InspectionNo": "", "Inspe...

{ "QualityItem": "取付確認", "ToolManageNo": "FM-5973", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-C06", "Other": "ﾏｸﾞﾈｯﾄ", "ProcessNames": [ "作業者安全工程", "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｽﾄｯﾊﾟｰ(F,R)・干渉ｾﾝｻｰ(Rのみ)取付", "WorkItems": [ "1. SCREW にNUT を挿入する", "2. ①に1完成品とSTOPPER を取付ける", "3. 2完成品にSENSOR をBOLT WASHER WASHER で取付ける", "1. SCREW にNUT を挿入する", "2. ①に1完成品とSTOPPER を取付ける", "3. 2完成品にSENSOR をBOL...

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "19㎜", "ToolOther": "6.0N･m", "WorkName": "ｽﾄｯﾊﾟｰ(F,R)・干渉ｾﾝｻｰ(Rのみ)取付", "WorkItems": [ "1. SCREW にNUT を挿入する", "2. ①に1完成品とSTOPPER を取付ける", "3. 2完成品にSENSOR をBOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "出代:37.5㎜を確認し取付ける事", "※K052-2(R側)のみ" ], ...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "40cN･m", "WorkName": "ｽﾄｯﾊﾟｰ(F,R)・干渉ｾﾝｻｰ(Rのみ)取付", "WorkItems": [ "1. SCREW にNUT を挿入する", "2. ①に1完成品とSTOPPER を取付ける", "3. 2完成品にSENSOR をBOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "出代:37.5㎜を確認し取付ける事", "※K052-2(R側)のみ" ]...

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "40cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾕﾆｯﾄ銘板貼付", "WorkItems": [ "2. ①②に③を貼付ける", "1. ①②の貼付け面を脱脂する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6061", "WorkName": "ﾊｰﾈｽ引き回し1", "WorkItems": [ "1. CABLE を引き回す" ], "WorkPoints": [ "V±aK301", "COM6a", "±aK3010.09/10/11", "101.02/03", ":ｽﾀｰﾄ :ｺﾞｰﾙ", "HDP", "A1bK201", "-VaT1022aF123", ...