input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑦(30連交換台車対応)",
"WorkItems": [],
"WorkPoints": [
"ﾏｰｷﾝｸﾞは治具を外して実施する事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑧(30連交換台車対応)",
"WorkItems": [],
"WorkPoints": [
"裏側よりBOLT で各2箇所締結",
"治具取り外し"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑧(30連交換台車対応)",
"WorkItems": [],
"WorkPoints": [
"裏側よりBOLT で各2箇所締結",
"治具取り外し"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑨(30連交換台車対応)",
"WorkItems": [
"3. ｲﾝｼｭﾛｯｸで固定(4箇所)",
"1. TUBE に㉘で30ｍｍ切り目を入れる",
"2. ①に1完成品を被せる(4箇所)",
"3. ｲﾝｼｭﾛｯｸで固定(4箇所)"
],
"WorkPoints": [
"切り目位置",
"ｽﾌﾟﾘﾝｸﾞの山と山の間をｲﾝｼｭﾛｯｸで閉める",
"切り目位置",... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で出来ていること指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛﾜｺﾈｸﾀ部組立(30連交換台車対応)",
"WorkItems": [
"1. TUBE TUBE を指定の長さにｶｯﾄする",
"2. ①にTUBE TUBE JOINT JOINT JOINT を挿入し､反対側の先端から約50㎜にA･B･Cの記号を黄ﾏｰｶｰで記入"
],
"WorkPoints": [
"L=680㎜:3本(ﾌﾛﾝﾄのみの仕様の場合)L=680㎜:6本(ﾌﾛﾝﾄ､ﾘｱ仕様の場合)",
"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で出来ていること指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "細目",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ前段取り①(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. PLATE に油砥石をかける"
],
"WorkPoints": [
"両面にかける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"砥石... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "細目",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ前段取り③(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. PLATE に㉖をかける"
],
"WorkPoints": [
"両面にかける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"砥石掛け... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "細目",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ前段取り④(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. PLATE に㉖をかける"
],
"WorkPoints": [
"両面にかける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"砥石掛け... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑤(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. ①にBOLT を取付(4箇所)"
],
"WorkPoints": [
"A側から見て左側に面取りがくる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑥(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. ①にSPACER を取付",
"2. 1完成品に③を取付"
],
"WorkPoints": [
"表裏があるので注意M3ﾀｯﾌﾟの位置で確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑦(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"2. ㉗の治具にセットしSPRING を取付ける",
"◆1. ①のｽﾌﾟﾘﾝｸﾞ取付面にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"治具から浮き上がりが無い事",
"ｽﾌﾟﾘﾝｸﾞの両端面にもｸﾞﾘｰｽ塗布すること"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ組立治具",
"Size": "",
"ToolOther": "FM-2324",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑦(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"2. ㉗の治具にセットしSPRING を取付ける",
"◆1. ①のｽﾌﾟﾘﾝｸﾞ取付面にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ｽﾌﾟﾘﾝｸﾞの両端面にもｸﾞﾘｰｽ塗布すること"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2324",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "12㎜",
"ToolOther": "20.3N･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑧(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. ①をNUT で締結"
],
"WorkPoints": [
"FM-2324"
],
"Tolks": [
"締付ﾄﾙｸ 20.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ組立治具",
"Size": "",
"ToolOther": "FM-2324",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑧(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. ①をNUT で締結"
],
"WorkPoints": [
"FM-2324"
],
"Tolks": [
"締付ﾄﾙｸ 20.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2324",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T10H",
"ToolOther": "150cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑨(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"2. 1完成品に①を治具に取付､BOLT で締結"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑨(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. ㉘にCOUPLER を差込む",
"2. 1完成品に①を治具に取付､BOLT で締結"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑩(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"3. BOLT で左右2箇所を締結"
],
"WorkPoints": [
"左右2箇所",
"左右2箇所",
"ﾏｰｷﾝｸﾞは治具を外して実施する事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑩(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"3. BOLT で左右2箇所を締結"
],
"WorkPoints": [
"左右2箇所",
"左右2箇所",
"ﾏｰｷﾝｸﾞは治具を外して実施する事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑪(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [],
"WorkPoints": [
"裏側よりBOLT で各2箇所締結",
"治具取り外し"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑪(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"2. ②を挿入し裏からBOLT で締結",
"1. ①を反転させて､治具を取り外す"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄの傾きは目視で真っすぐ合わせる",
"裏側よりBOLT で各2箇所締結",
"治具取り外し"
],
"Tolks": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑫(17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. TUBE に㉘で30ｍｍ切り目を入れる",
"2. ①に1完成品を被せる(4箇所)",
"3. ｲﾝｼｭﾛｯｸで固定(4箇所)"
],
"WorkPoints": [
"切り目位置",
"切り目位置"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で出来ていること指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛﾜｺﾈｸﾀ部配管接続(17連交換台車仕様)",
"WorkItems": [
"1. ②③を右記の寸法にｶｯﾄする",
"2. ①に②③④を挿入し反対側の先端から約50㎜にA･B･Cの記号を黄ﾏｰｶｰで記入"
],
"WorkPoints": [
"17連交換台車対応ﾕﾆｯﾄ(FL)",
"17連交換台車対応ﾕﾆｯﾄ(FR)",
"800mm",
"240mm",
"1210mm",... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で出来ていること指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛﾜｺﾈｸﾀ部配管接続(交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"2. ①にTUBE TUBE JOINT JOINT JOINT を挿入し反対側の先端から約50㎜にA･B･の記号を黄ﾏｰｶｰで記入",
"1. TUBE TUBE を右記の寸法にｶｯﾄする"
],
"WorkPoints": [
"ITF17連/ASF34連交換台車対応ﾕﾆｯﾄ(後側&右側&ﾄﾚｲ) (RL)",
"ITF17連/... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で出来ていること指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛﾜｺﾈｸﾀ延長対応部組立(交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"2. BOLT をH1工程へ払出す",
"1. PLATE にPIN を圧入する"
],
"WorkPoints": [
"出代:5.0㎜±0.5㎜",
"PIN の圧入位置に注意する",
"前側､後側ﾄﾚｲ時 2ｹ製作",
"前側､後側切替仕様時 2ｹ製作"
],
"Tolks": [],
... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "PIN出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻｰﾌﾞﾗｹｯﾄ(F/R、R/L)組立①",
"WorkItems": [
"2. 1完成品へBUSH BUSH を指示された寸法にｶｯﾄし貼付ける",
"1. BRACKET へBUSH BUSH を指示された寸法にｶｯﾄし貼付ける",
"2. 1完成品へBUSH BUSH を指示された寸法にｶｯﾄし貼付ける",
"1. BRACKET へBUSH BUSH を指示された寸法にｶｯﾄし貼付ける"
],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で出来ていること指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻｰﾌﾞﾗｹｯﾄ(F/R、R/L)組立②",
"WorkItems": [
"1. ①へLABEL を貼付ける"
],
"WorkPoints": [
"F/R",
"R/L"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Word... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻｰﾌﾞﾗｹｯﾄ(F/L、R/R)組立①",
"WorkItems": [
"1. BRACKET へBUSH BUSH を指示された寸法にｶｯﾄし貼付ける"
],
"WorkPoints": [
"108㎜､19㎜ ×各2"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で出来ていること指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻｰﾌﾞﾗｹｯﾄ(F/L、R/R)組立②",
"WorkItems": [
"1. ①へLABEL を貼付ける"
],
"WorkPoints": [
"F/L",
"R/R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Word... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ部(台車仕様)(ﾄﾚｲ仕様)(前側)(後側)組立",
"WorkItems": [
"1. POST にSCREW を仮付けする",
"3. POST にSCREW を仮付けする",
"2. POST にSCREW を仮付けする"
],
"WorkPoints": [
"30連交換台車仕様時",
"17連交換台車仕様時",
"ﾘｱY軸ｽﾄｯﾊﾟｰ部(台車仕様)(後側)",
"リア 17+... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備1",
"WorkItems": [
"1. CABLE-SUPPORT JOINT をH1工程に払い出す"
],
"WorkPoints": [
"基板ﾎﾙﾀﾞｼﾝｸﾞﾙ仕様時払出し(基板ﾎﾙﾀﾞｼﾝｸﾞﾙﾘｱ用ﾒｸﾗ)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
... | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "ﾄﾞﾛﾜｺﾈｸﾀ部配管接続(ﾄﾚｲﾌｨｰﾀﾞ連結部切替仕様)",
"WorkItems": [
"2. ①にTUBE TUBE JOINT を挿入し反対側の先端から約50㎜にA･B･の記号を黄ﾏｰｶｰで記入",
"1. TUBE TUBE を右記の寸法にｶｯﾄする"
],
"WorkPoints": [
"ﾄﾚｲﾌｨｰﾀﾞ連結部切替仕様Rear側(本体側):NPM-GW(RL)",
"ﾄﾚｲﾌｨｰﾀﾞ連結部切替仕様F... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で出来ていること指示寸法±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱｶﾞｲﾄﾞ前準備",
"WorkItems": [],
"WorkPoints": [
"基準面(加工面)"
],
"Tolks": [
"締付ﾄﾙｸ 0.4N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｽﾗｲﾀﾞｰ移動"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "加工面に打痕､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "0.4N･m",
"WorkName": "Y軸ﾘﾆｱｶﾞｲﾄﾞ前準備",
"WorkItems": [
"1. LINEAR-WAY ﾘﾆｱｶﾞｲﾄﾞの防錆油をｳｴｽで拭き取り錆や傷を確認する",
"2. 1完成品にJOINT を取付ける"
],
"WorkPoints": [
"ｽﾗｲﾀﾞｰを移動させてﾚｰﾙ全体の防錆油を拭き取る",
"･JOINT を手で軽く締め止まったところ(着座)から45度締付ける･締めすぎに注意し向きを合わせる"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.4N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "XYﾕﾆｯﾄ取付け前の架台ﾚﾍﾞﾙ確認",
"WorkItems": [],
"WorkPoints": [
"※ｽﾞﾚ方向の符号",
"下記位置に水準器設置",
"XY均等に調整する",
"FRONT",
"全ｱｼﾞｬｽﾄﾎﾞﾙﾄの浮き発生が無いことを確認"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionIte... | {
"QualityItem": "水準確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.06㎜/m以下",
"Method": "水準器",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾗﾝｽ取付け前準備",
"WorkItems": [
"◆3. ﾄﾗﾝｽと吊り上げﾌﾞﾗｹｯﾄの間に移載治具が入るように治具側の高さを合わせる",
"2. 吊り上げﾌﾞﾗｹｯﾄのM8ﾎﾞﾙﾄ(PIN付:4箇所)をﾄﾗﾝｽに穴にはめ込み取付ける",
"◆5. ﾗﾁｪｯﾄｽﾊﾟﾅを左右に動かしてﾄﾗﾝｽを吊り上げる",
"◆4. 移載治具を吊り上げﾊﾞｰと吊り上げﾌﾞﾗｹｯﾄが干渉する箇所まで入れ込む",
"■1. 付属の検査書とTRA... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾗﾝｽ取付け前準備",
"WorkItems": [
"◆3. ﾄﾗﾝｽと吊り上げﾌﾞﾗｹｯﾄの間に移載治具が入るように治具側の高さを合わせる",
"2. 吊り上げﾌﾞﾗｹｯﾄのM8ﾎﾞﾙﾄ(PIN付:4箇所)をﾄﾗﾝｽに穴にはめ込み取付ける",
"◆5. ﾗﾁｪｯﾄｽﾊﾟﾅを左右に動かしてﾄﾗﾝｽを吊り上げる",
"◆4. 移載治具を吊り上げﾊﾞｰと吊り上げﾌﾞﾗｹｯﾄが干渉する箇所まで入れ込む",
"■1. 付属の検査書とTRA... | {
"QualityItem": "製造番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾗﾝｽ取付け前準備",
"WorkItems": [
"◆3. ﾄﾗﾝｽと吊り上げﾌﾞﾗｹｯﾄの間に移載治具が入るように治具側の高さを合わせる",
"2. 吊り上げﾌﾞﾗｹｯﾄのM8ﾎﾞﾙﾄ(PIN付:4箇所)をﾄﾗﾝｽに穴にはめ込み取付ける",
"◆5. ﾗﾁｪｯﾄｽﾊﾟﾅを左右に動かしてﾄﾗﾝｽを吊り上げる",
"◆4. 移載治具を吊り上げﾊﾞｰと吊り上げﾌﾞﾗｹｯﾄが干渉する箇所まで入れ込む",
"■1. 付属の検査書とTRA... | {
"QualityItem": "検査書確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査書がある事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ移載治具",
"Size": "",
"ToolOther": "FM-4451",
"WorkName": "ﾄﾗﾝｽ取付け前準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"■安全作業",
"◆作業者安全作業",
"■安全作業",
"◆作業者安全作業",
"■安全作業"
]... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4451",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ吊上げﾊﾞｰ",
"Size": "",
"ToolOther": "FM-5846",
"WorkName": "ﾄﾗﾝｽ取付け前準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"■安全作業",
"◆作業者安全作業",
"■安全作業",
"◆作業者安全作業",
"■安全作業"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5846",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ吊上げﾌﾞﾗｹｯﾄ",
"Size": "",
"ToolOther": "FM-5847",
"WorkName": "ﾄﾗﾝｽ取付け前準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"■安全作業",
"◆作業者安全作業",
"■安全作業",
"◆作業者安全作業",
"■安全作業"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5847",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ移載治具",
"Size": "",
"ToolOther": "FM-4451",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"◆2. ①の高さを架台へ入れ込めるように調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4451",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ吊上げﾊﾞｰ",
"Size": "",
"ToolOther": "FM-5846",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"◆2. ①の高さを架台へ入れ込めるように調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5846",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ吊上げﾌﾞﾗｹｯﾄ",
"Size": "",
"ToolOther": "FM-5847",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"◆2. ①の高さを架台へ入れ込めるように調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5847",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽｽﾗｲﾄﾞｼｰﾄ",
"Size": "",
"ToolOther": "FM-6398",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"1. ｽﾗｲﾄﾞｼｰﾄA､Bをｾｯﾃｨﾝｸﾞする",
"◆2. ①の高さを架台へ入れ込めるように調整する",
"◆3. トランスを㉙の上に真直ぐ入れ込む",
"◆4. ﾄﾗﾝｽを下降させ移載治具を抜く",
"◆5. ﾄﾗﾝｽを取付け位置まで右方向にｽﾗｲﾄﾞさせる",
"6. ㉙を外す",
"7. ﾄﾗﾝｽをBOLT WASHE... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6398",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜",
"ToolOther": "40.0N･m",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"◆5. ﾄﾗﾝｽを取付け位置まで右方向にｽﾗｲﾄﾞさせる"
],
"WorkPoints": [
"ﾗﾁｪｯﾄｽﾊﾟﾅを左右に動かして高さ調整する",
"Bと共にﾄﾗﾝｽを右にｽﾗｲﾄﾞﾞさせる"
],
"Tolks": [
"締付ﾄﾙｸ 40.0N･m"
],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "FG・台車中継・感電注意ｼｰﾙ貼付け",
"WorkItems": [
"1. LABEL LABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付け前に㉖で拭き取ること",
"53㎜",
"80㎜",
"ﾏｽｷﾝｸﾞ左上に合わせること",
"ﾏｽｷﾝｸﾞ左上に合わせること"
],
"Tolks": [],
"InspectionNo": "",
"Ins... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "冷却ﾌｧﾝ・MASSCENTERｼｰﾙ貼付け",
"WorkItems": [
"1. LABEL を架台に貼付ける"
],
"WorkPoints": [
"20㎜",
"129㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "FG・台車中継ｼｰﾙ貼付け",
"WorkItems": [
"1. LABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付け前に㉖で拭き取ること",
"ﾏｽｷﾝｸﾞ左下に合わせること",
"ﾏｽｷﾝｸﾞ左下に合わせること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACｹｰﾌﾞﾙ接続【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"■1. ①の端子台にCABLE CABLE を接続する",
"2. 1完成品のAC線を結束する"
],
"WorkPoints": [
"被覆部先端を合わせて固定する",
"ｷﾞｻﾞｷﾞｻﾞ面を下向きで奥まで差込む",
"差込み後､ｹｰﾌﾞﾙの引っ張り確認を実施し抜けないことを確認",
"仕様に合わせて作業を実施のこと",
"P... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D14",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏﾙﾁﾃｽﾀ",
"Size": "",
"ToolOther": "",
"WorkName": "電源ｹｰﾌﾞﾙ導通確認【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. ﾊﾟﾜｰﾕﾆｯﾄのﾀｰﾐﾅﾙﾌﾞﾛｯｸに黒端子を当てる",
"2. 各測定箇所に赤端子を当て導通確認を行い､検査表に記入する"
],
"WorkPoints": [
"ｱｰｽ線を下にして左下端子に当てる",
"規格値:0Ω~0.1Ω"
],
"Tolks": [],
"InspectionNo": "WETE-G002-... | {
"QualityItem": "導通確認",
"ToolManageNo": "-",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "0Ω~0.10Ω",
"Method": "ﾏﾙﾁﾃｽﾀ",
"RecordMethod": "WETE-G002-D14",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ引き回し①",
"WorkItems": [
"1. ﾄﾞﾗｲﾊﾞｰ･ﾄﾚｲ電源線をﾘｱ側に送る"
],
"WorkPoints": [
"ｹｰﾌﾞﾙの配置",
"この穴からﾘｱ側へ送る",
"CPU電源線も一緒に引き回す",
"P1K504",
"P1K504",
"K503",
"TRAY.PR(ﾄﾚｲ仕様時のみ)",
"K503を上にして収縮ﾁｭｰﾌﾞ... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "白ｶﾊﾞｰ固定用ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"左側",
"右側",
"手前側に当付け取付けこと"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾒｲﾝｽｲｯﾁ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6383",
"WorkName": "ﾒｲﾝﾌﾞﾚｰｶｰ取付け",
"WorkItems": [
"1. ㉖で①の上下・左右方向が中央になるように位置決めしBOLT WASHER で取付ける",
"2. ｹｰﾌﾞﾙを架台に固定する"
],
"WorkPoints": [
"ｹｰﾌﾞﾙ挿入 → 位置決め → 固定の順",
"上下方向調整",
"ｼﾞｸﾞ取付け",
"固定ﾎﾞﾙﾄ",
"当付け方向",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6383",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "ﾒｲﾝﾌﾞﾚｰｶｰ取付け",
"WorkItems": [
"1. ㉖で①の上下・左右方向が中央になるように位置決めしBOLT WASHER で取付ける",
"2. ｹｰﾌﾞﾙを架台に固定する"
],
"WorkPoints": [
"ｹｰﾌﾞﾙ挿入 → 位置決め → 固定の順",
"上下方向調整",
"ｼﾞｸﾞ取付け",
"固定ﾎﾞﾙﾄ",
"当付け方向",
"仮取... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾒｲﾝﾌﾞﾚｰｶｰ取付け",
"WorkItems": [
"1. ㉖で①の上下・左右方向が中央になるように位置決めしBOLT WASHER で取付ける",
"2. ｹｰﾌﾞﾙを架台に固定する"
],
"WorkPoints": [
"ｹｰﾌﾞﾙ挿入 → 位置決め → 固定の順",
"上下方向調整",
"ｼﾞｸﾞ取付け",
"固定ﾎﾞﾙﾄ",
"当付け方向",
"仮取... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｱｰｽﾌﾟﾚｰﾄ取付け",
"WorkItems": [
"1. ｱｰｽﾌﾟﾚｰﾄをBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｱｰｽﾌﾟﾚｰﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.2N･m",
"WorkName": "ｻｰｼﾞﾌﾟﾛﾃｸﾀｰ取付け",
"WorkItems": [
"1. ｻｰｼﾞﾌﾟﾛﾃｸﾀｰをBOLT WASHER WASHER で取付ける",
"2. ｹｰﾌﾞﾙを架台に固定する"
],
"WorkPoints": [
"ｱｰｽﾋﾞｽが正面から見えるよう固定する",
"ｱｰｽ線の余長も一緒に固定する"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾀｰﾐﾅﾙﾌﾞﾛｯｸ取付け",
"WorkItems": [
"1. ﾀｰﾐﾅﾙﾌﾞﾛｯｸをBOLT WASHER で取付ける",
"2. ｹｰﾌﾞﾙを架台に固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "1次側電源ｹｰﾌﾞﾙ接続",
"WorkItems": [
"1. 架台穴から通した1次電源ｹｰﾌﾞﾙを①に通しBOLT WASHER で取付ける",
"3. CLIP をBOLT WASHER WASHER にて取付ける",
"4. ﾌﾞｯｼｭを締める"
],
"WorkPoints": [
"①のﾌﾞﾗｹｯﾄ開口部を正面から見て奥側になるように取付けること",
"端子台~ﾌﾞｯｼｭ間のｹｰﾌﾞ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "2.2N･m",
"WorkName": "1次側電源ｹｰﾌﾞﾙ接続",
"WorkItems": [
"1. 架台穴から通した1次電源ｹｰﾌﾞﾙを①に通しBOLT WASHER で取付ける",
"3. CLIP をBOLT WASHER WASHER にて取付ける",
"4. ﾌﾞｯｼｭを締める"
],
"WorkPoints": [
"①のﾌﾞﾗｹｯﾄ開口部を正面から見て奥側になるように取付けること",
"端子台~ﾌﾞｯｼｭ間のｹｰﾌﾞ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "1次側電源ｹｰﾌﾞﾙ接続",
"WorkItems": [
"1. 架台穴から通した1次電源ｹｰﾌﾞﾙを①に通しBOLT WASHER で取付ける",
"3. CLIP をBOLT WASHER WASHER にて取付ける",
"4. ﾌﾞｯｼｭを締める",
"■2. ﾀｰﾐﾅﾙﾌﾞﾛｯｸに電源ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"①のﾌﾞﾗｹｯﾄ開口部を正面から見て奥側になるように取付けること"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "1次側ﾄﾗﾝｽｹｰﾌﾞﾙ固定・接続",
"WorkItems": [
"1. 1次側ﾄﾗﾝｽｹｰﾌﾞﾙを引き回し､固定する",
"■2. ﾄﾗﾝｽ1次側ｹｰﾌﾞﾙを端子台に接続する",
"3. CPのOFFを確認する"
],
"WorkPoints": [
"差込み後､ｹｰﾌﾞﾙの引っ張り確認を実施し抜けないことを確認",
"ｷﾞｻﾞｷﾞｻﾞ面を左向きで奥まで差込む",
"Ed4X1のｱｰｽ線をﾊﾟﾜｰﾕﾆｯﾄま... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ取付け・ｹｰﾌﾞﾙの固定",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"5/6/7K302"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "2次側端子台ｹｰﾌﾞﾙ接続・ﾊﾟﾜｰﾕﾆｯﾄ端子台ｹｰﾌﾞﾙ接続",
"WorkItems": [
"■2. ﾊﾟﾜｰﾕﾆｯﾄ端子台にｹｰﾌﾞﾙを接続する",
"■1. 2次側端子台にｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"差込み後､ｹｰﾌﾞﾙの引っ張り確認を実施し抜けないことを確認",
"ｷﾞｻﾞｷﾞｻﾞ面を右向きで奥まで差込む",
"差込み後､ｹｰﾌﾞﾙの引っ張り確認を実施し抜けないことを確認"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ引き回し②",
"WorkItems": [
"1. ﾊﾟﾜｰﾕﾆｯﾄからのACｹｰﾌﾞﾙを引き回し固定する"
],
"WorkPoints": [
"P1K502",
"K501",
"TRAY.PF(ﾄﾚｲ仕様時のみ)",
"TRAY.PF",
"ﾌｧｲﾊﾞｰ線も一緒に固定する",
"ﾄﾚｲ仕様時のみ作業実施のこと",
"K501を上にして収縮ﾁｭｰﾌﾞの中央にて... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "FG端子固定",
"WorkItems": [
"■1. 電源ｹｰﾌﾞﾙのFG端子をSCREW SCREW SCREW で固定する"
],
"WorkPoints": [
"FG2K502",
"FG4K502",
"FG2K501",
"FGTF(F側ﾄﾚｲ仕様時のみ)",
"FGTR(R側ﾄﾚｲ仕様時のみ)"
],
"Tolks": [
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "FG端子固定",
"WorkItems": [
"■1. 電源ｹｰﾌﾞﾙのFG端子をSCREW SCREW SCREW で固定する"
],
"WorkPoints": [
"FG2K502",
"FG4K502",
"FG2K501",
"FGTF(F側ﾄﾚｲ仕様時のみ)",
"FGTR(R側ﾄﾚｲ仕様時のみ)"
],
"Tolks": [
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "180cN･m",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [
"3. LABEL を貼付ける",
"3. LABEL を貼付ける"
],
"WorkPoints": [
"貼付け前に㉙で拭き取ること",
"貼付け前に㉙で拭き取ること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "中継基板取付治具(I/O基板用)",
"Size": "",
"ToolOther": "FM-4667",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [
"3. LABEL を貼付ける"
],
"WorkPoints": [
"貼付け前に㉙で拭き取ること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4667",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "中継基板取付治具(搬送基板用)",
"Size": "",
"ToolOther": "FM-6636",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [
"3. LABEL を貼付ける"
],
"WorkPoints": [
"貼付け前に㉙で拭き取ること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6636",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [
"3. LABEL を貼付ける"
],
"WorkPoints": [
"貼付け前に㉙で拭き取ること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "CPU-BOX取付け",
"WorkItems": [
"2. ①②をBOLT WASHER で取付ける",
"1. ①にﾗｲｾﾝｽｼｰﾙが貼付けられていることを確認する"
],
"WorkPoints": [
"A矢視",
"CPU-BOXと配線の干渉が無いこと",
"同じﾎﾞﾙﾄを使用しているので､ﾄﾙｸに注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "CPU-BOX取付け",
"WorkItems": [
"2. ①②をBOLT WASHER で取付ける",
"1. ①にﾗｲｾﾝｽｼｰﾙが貼付けられていることを確認する"
],
"WorkPoints": [
"A矢視",
"CPU-BOXと配線の干渉が無いこと",
"同じﾎﾞﾙﾄを使用しているので､ﾄﾙｸに注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOX取付け",
"WorkItems": [
"2. ①②をBOLT WASHER で取付ける",
"1. ①にﾗｲｾﾝｽｼｰﾙが貼付けられていることを確認する"
],
"WorkPoints": [
"A矢視",
"CPU-BOXと配線の干渉が無いこと",
"同じﾎﾞﾙﾄを使用しているので､ﾄﾙｸに注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾗｲｾﾝｽｼｰﾙが貼付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOX電源ｹｰﾌﾞﾙ・ﾌｧｲﾊﾞｰ線接続",
"WorkItems": [
"1. 電源ｹｰﾌﾞﾙ･ﾌｧｲﾊﾞｰ線を接続する"
],
"WorkPoints": [
"差込んだ後ｸﾘｯﾌﾟで固定する",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D05",
"InspectionItems": [
"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "天井ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"左側",
"右側"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "架台内ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"左側",
"右側"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入",
"WorkItems": [
"1. ﾘｱ側からﾌﾛﾝﾄ側への束線の投入ｻﾎﾟｰﾄを行う"
],
"WorkPoints": [
"ｺﾈｸﾀやｹｰﾌﾞﾙを架台に引っ掛けないように注意すること",
"非常停止ｽｲｯﾁの端子を曲げないように注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定①(右側)",
"WorkItems": [
"1. 右側面のｹｰﾌﾞﾙを引き回し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定②(右側)",
"WorkItems": [
"1. 右側面のｹｰﾌﾞﾙを引き回し固定する"
],
"WorkPoints": [
"穴より上側へ",
"架台内側へ",
"非常停止を先に通す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定③(右側)",
"WorkItems": [
"1. 右側面のｹｰﾌﾞﾙを引き回し固定する",
"2. ｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付ける"
],
"WorkPoints": [
"CART.F2MP",
"CART.F2P1",
"B1010R 他は架台上には出さない"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D05",
"Ins... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "4.5",
"ToolOther": "15cN･m",
"WorkName": "CPU-BOXDCｹｰﾌﾞﾙ接続",
"WorkItems": [
"1. DCｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"1/2A12の束線は固定しない"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D05",
"InspectionItems": [
"検査表SCREW :4.CPU BOX確認"
],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "CPU-BOXDCｹｰﾌﾞﾙ接続",
"WorkItems": [
"1. DCｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"1/2A12の束線は固定しない"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOXDCｹｰﾌﾞﾙ接続",
"WorkItems": [
"1. DCｹｰﾌﾞﾙを固定する",
"■3. ｹｰﾌﾞﾙについているRoHSﾏｰｸを確認する",
"■2. DCｹｰﾌﾞﾙ系を接続しFG線をSCREW で固定する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"ﾈｼﾞ締めﾀｲﾌﾟのｺﾈｸﾀは上下均等に締め込んでいく",
"1/2A12の束線... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOXDCｹｰﾌﾞﾙ接続",
"WorkItems": [
"1. DCｹｰﾌﾞﾙを固定する",
"■3. ｹｰﾌﾞﾙについているRoHSﾏｰｸを確認する",
"■2. DCｹｰﾌﾞﾙ系を接続しFG線をSCREW で固定する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"ﾈｼﾞ締めﾀｲﾌﾟのｺﾈｸﾀは上下均等に締め込んでいく",
"1/2A12の束線... | {
"QualityItem": "ﾏｰｸ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "RoHSﾏｰｸがある事",
"Method": "目視",
"RecordMethod": "WETE-G002-D10",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定④(右側)・FGｸﾗﾝﾌﾟ取付け",
"WorkItems": [
"1. 右側面のｹｰﾌﾞﾙを引き回し固定する",
"■2. USBｹｰﾌﾞﾙをCABLE-SUPPORT に通しSCREW で固定する"
],
"WorkPoints": [
"FGｼｰﾙの貼付け確認も行う"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定⑤(左側)",
"WorkItems": [
"1. 左側面のｹｰﾌﾞﾙを引き回し固定する"
],
"WorkPoints": [
"B1231/2/3/4/5 1S3211P 他は抜き穴から外側に出す",
"右上の穴に差込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定⑥(左側)",
"WorkItems": [
"1. 右側面のｹｰﾌﾞﾙを引き回し固定する",
"2. ｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付ける"
],
"WorkPoints": [
"CART.F1P1",
"CART.F1MP"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D05",
"InspectionItems": [
"検査表①... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定⑦(左側)",
"WorkItems": [
"1. 右側面のｹｰﾌﾞﾙを引き回し固定する"
],
"WorkPoints": [
"穴より上側へ",
"ﾄﾚｲ仕様時のみ",
"B1046P 他は架台上には上げないこの辺りに置いておく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "I/O中継基板接続",
"WorkItems": [
"1. I/O中継基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D05",
"InspectionItems": [
"検査表①:7.ｺﾈｸﾀ中継基板確認1"
],
"WorkTypes": ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送中継基板",
"WorkItems": [
"1. 搬送中継基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時のみ接続する"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D05",
"InspectionItems": [
"検査表①:7.ｺﾈｸﾀ中継基板確認1... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜ﾛﾝｸﾞ",
"ToolOther": "3.2N･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰ取付け",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ②③をBOLT WASHER で取付ける",
"3. ④をBOLT WASHER で取付ける"
],
"WorkPoints": [
"同じﾎﾞﾙﾄを使用しているので､ﾄﾙｸに注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜ﾛﾝｸﾞ",
"ToolOther": "6.0N･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰ取付け",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ②③をBOLT WASHER で取付ける",
"3. ④をBOLT WASHER で取付ける",
"1. ①をBOLT WASHER で取付ける",
"2. ②③をBOLT WASHER で取付ける",
"3. ④をBOLT WASHER で取付ける"
],
"Wo... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "15cN･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰAC・DCｹｰﾌﾞﾙ接続①",
"WorkItems": [
"■1. ｺﾈｸﾀ･ｱｰｽ線を接続し配線を固定する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CN3K501/2は上下均等に取付けﾈｼﾞを締めこんでいく"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰAC・DCｹｰﾌﾞﾙ接続①",
"WorkItems": [
"■1. ｺﾈｸﾀ･ｱｰｽ線を接続し配線を固定する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CN3K501/2は上下均等に取付けﾈｼﾞを締めこんでいく"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120c... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾗｲﾊﾞｰAC・DCｹｰﾌﾞﾙ接続①",
"WorkItems": [
"■1. ｺﾈｸﾀ･ｱｰｽ線を接続し配線を固定する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CN3K501/2は上下均等に取付けﾈｼﾞを締めこんでいく"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"Inspe... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け・接続、FG線固【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. ①を⑳㉑で取付ける"
],
"WorkPoints": [
"5㎜",
"傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け・接続、FG線固【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. ①を⑳㉑で取付ける"
],
"WorkPoints": [
"5㎜",
"傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WETE-G002-D14",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け・接続、FG線固【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. ①を⑳㉑で取付ける"
],
"WorkPoints": [
"5㎜",
"傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け・接続、FG線固【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. ①を⑳㉑で取付ける",
"2. 電源･信号ｹｰﾌﾞﾙを接続する",
"■3. FG端子を②で固定する"
],
"WorkPoints": [
"TRAY.PF",
"TRAY.SF",
"5㎜",
"26㎜",
"傾き無き事"
],
"Tolks": [
"締付ﾄ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D14",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.