input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立1",
"WorkItems": [
"1. FRAME にBRACKET をBOLT WASHER で仮締め"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"仮止め:SD-A038963-021... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"1. 治具作業台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. ②を①に貼付",
"3. ①のアクリルシートをめくり㉙でとめ、脱脂",
"4. COVER にTAPE を貼付ける"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"矢印方向に当てつけ",
"貼付け後､手で仮圧着",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "5.5M",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"3. ①のアクリルシートをめくり㉙でとめ、脱脂",
"4. COVER にTAPE を貼付ける"
],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復",
"2本",
"2本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GH用扉組立台",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"1. 治具作業台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. ②を①に貼付"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"矢印方向に当てつけ",
"貼付け後､手で仮圧着",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす",
"治具番号1",
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞｱ組立台(NPM-GH用)",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"1. 治具作業台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. ②を①に貼付"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"矢印方向に当てつけ",
"貼付け後､手で仮圧着",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす",
"治具番号1",
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5890",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"3. ①のアクリルシートをめくり㉙でとめ、脱脂",
"4. COVER にTAPE を貼付ける"
],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復",
"2本",
"2本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GH用扉組立台",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立3",
"WorkItems": [
"1. ①に治具をｾｯﾄし②を貼付"
],
"WorkPoints": [
"治具は上側に押当",
"FM-5804",
"FM-5804",
"穴位置を合わせた後貼付けし､手で仮圧着",
"治具は上側に押当"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞｱ組立台(NPM-GH用)",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立3",
"WorkItems": [
"1. ①に治具をｾｯﾄし②を貼付"
],
"WorkPoints": [
"治具は上側に押当",
"FM-5804",
"FM-5804",
"穴位置を合わせた後貼付けし､手で仮圧着",
"治具は上側に押当"
],
"Tolks": [],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "開閉ｶﾊﾞｰ組立4",
"WorkItems": [
"3. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す",
"1. ①にPULL をBOLT WASHER WASHER で取付"
],
"WorkPoints": [
"BOLT 締結後閉じる",
"内側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "3.2N･m",
"WorkName": "開閉ｶﾊﾞｰ組立4",
"WorkItems": [
"2. 本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GH用扉組立台",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-5804",
"FM-5804",
"FM-5804",
"貼付け後､手で仮圧着",
"真ん中を目... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞｱ組立台(NPM-GH用)",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-5804",
"FM-5804",
"FM-5804",
"貼付け後､手で仮圧着",
"真... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1.2㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-5804",
"FM-5804",
"FM-5804",
"貼付け後､手で仮圧着",
"真ん中を目安に取付... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "作業指示通り出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GH用扉組立台",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立6",
"WorkItems": [
"1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. ②のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめる",
"3.2完成品に②を貼付け"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"FM-5804",
"治具に押し当てながら貼付",
"貼付け後､手で仮圧着"
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞｱ組立台(NPM-GH用)",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立6",
"WorkItems": [
"1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. ②のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめる",
"3.2完成品に②を貼付け"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"FM-5804",
"治具に押し当てながら貼付",
"貼付け後､手で仮圧... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GH用扉組立台",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立7",
"WorkItems": [
"1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"FM-5804",
"治具2,3を先に取付ける",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす"
],
"Tolks": [],
"InspectionNo"... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞｱ組立台(NPM-GH用)",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立7",
"WorkItems": [
"1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"FM-5804",
"治具2,3を先に取付ける",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす"
],
"Tolks": [],
"Inspectio... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "開閉ｶﾊﾞｰ組立7",
"WorkItems": [
"2. 1完成品に②を貼付け圧着"
],
"WorkPoints": [
"両ｻｲﾄﾞの治具に沿わせながら貼付",
"隙間が無い事",
"端面が合っている事",
"圧着ﾛｰﾗｰで2往復"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GH用扉組立台",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立8",
"WorkItems": [
"5. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す",
"4. ①に②③を貼付け圧着",
"3. 治具台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. SPRING-PLATE を取付(挟み込む)",
"1. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂"
],
"WorkPoints": [
"②を貼り終えてか... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞｱ組立台(NPM-GH用)",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立8",
"WorkItems": [
"5. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す",
"4. ①に②③を貼付け圧着",
"3. 治具台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. SPRING-PLATE を取付(挟み込む)",
"1. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂"
],
"WorkPoints": [
"②を貼り... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "開閉ｶﾊﾞｰ組立8",
"WorkItems": [
"5. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す",
"4. ①に②③を貼付け圧着",
"3. 治具台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. SPRING-PLATE を取付(挟み込む)",
"1. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂"
],
"WorkPoints": [
"②を貼り終え... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立8",
"WorkItems": [
"5. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す",
"4. ①に②③を貼付け圧着",
"3. 治具台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. SPRING-PLATE を取付(挟み込む)",
"1. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂"
],
"WorkPoints": [
"②を貼り終えてから③を貼る"
... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付",
"■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認、製造番号を転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C11",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付"
],
"WorkPoints": [],
"Tolks": [
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20N･m",
"WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付"
],
"WorkPoints": [],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付",
"■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKE... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認、製造番号を転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C11",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"3. COVER にBUSH を取付"
],
"WorkPoints": [
"端面を合わせる",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属波ﾜｯｼｬｰ"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20N･m",
"WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"3. COVER にBUSH を取付"
],
"WorkPoints": [
"端面を合わせる",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属波ﾜｯｼｬｰ"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "開閉ｶﾊﾞｰ組立11(ﾋﾝｼﾞ組立)",
"WorkItems": [
"3. HINGE を再度組立",
"◆1. HINGE の青枠線内にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"外したEﾘﾝｸﾞで固定",
"組み合わせ方向･ﾋﾟﾝ挿入方向に注意<下図参照>"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)",
"WorkItems": [
"2. ｲﾝｼｭﾛｯｸで配線を固定",
"3. 2完成品を脱脂後､LABEL を貼付",
"1. BRACKET にSWITCH をBOLT NUT で取付"
],
"WorkPoints": [
"裏面",
"開閉ｶﾊﾞｰSWのF側･R側で銘板を貼付け",
"BRACKET ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰSWSWITCH 開閉ｶﾊﾞｰSWの､... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認、製造番号を転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)",
"WorkItems": [
"2. ｲﾝｼｭﾛｯｸで配線を固定",
"1. BRACKET にSWITCH をBOLT NUT で取付"
],
"WorkPoints": [
"BRACKET ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰSWSWITCH 開閉ｶﾊﾞｰSWの､ﾛｯﾄNOを(F側･R側)合わせる事",
"ﾅｯﾄ側も同等のﾄﾙｸで締め付けの事"
],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)",
"WorkItems": [
"2. ｲﾝｼｭﾛｯｸで配線を固定",
"3. 2完成品を脱脂後､LABEL を貼付",
"1. BRACKET にSWITCH をBOLT NUT で取付"
],
"WorkPoints": [
"裏面",
"開閉ｶﾊﾞｰSWのF側･R側で銘板を貼付け",
"BRACKET ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰSWSWITCH 開... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)",
"WorkItems": [],
"WorkPoints": [
"開閉ｶﾊﾞｰSWのF側･R側で銘板を貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"2mm",
"1mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T20",
"ToolOther": "194cN･m",
"WorkName": "開閉ｶﾊﾞｰ組立13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"治具をあてつける",
"2. 1完成品にCABLE またはCABLE を挿入",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ安全SW調整治具(Gｼﾘｰｽﾞ)",
"Size": "",
"ToolOther": "FM-6034",
"WorkName": "開閉ｶﾊﾞｰ組立13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"治具をあてつける",
"2. 1完成品にCABLE またはCABLE を挿入... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6034",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D06",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"治具をあてつける",
"1. ①にBUSH を取付",
"2. 1完成品にCABLE またはCA... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立14",
"WorkItems": [
"1. ①の配線をｲﾝｼｭﾛｯｸで固定",
"3 2完成品にRUBBER-CUSHION を取付",
"2. 1完成品に黄色ﾏｰｷﾝｸﾞ"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸと配線の位置関係",
"ｲﾝｼｭﾛｯｸが配線の下側にくる事",
"左右に取付け",
"ﾌﾚｰﾑ内に通す",
"ｲﾝｼｭﾛｯｸの(頭)方向は内側のこ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立14",
"WorkItems": [
"3 2完成品にRUBBER-CUSHION を取付",
"2. 1完成品に黄色ﾏｰｷﾝｸﾞ"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸと配線の位置関係",
"ｲﾝｼｭﾛｯｸが配線の下側にくる事",
"左右に取付け",
"ﾌﾚｰﾑ内に通す",
"ｲﾝｼｭﾛｯｸの(頭)方向は内側のこと"
],
"Tolks":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "開閉ｶﾊﾞｰ組立15(ﾀﾞﾝﾊﾟｰ取付け)",
"WorkItems": [
"1. ②③にｸｯｼｮﾝ材を巻く",
"2. ①に1完成品をWASHER BOLT で取付"
],
"WorkPoints": [
"取付目安1.25mm",
"矢印方向に押し当てて取付",
"取付場所2か所あり"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"Ins... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立15(ﾀﾞﾝﾊﾟｰ取付け)",
"WorkItems": [
"1. ②③にｸｯｼｮﾝ材を巻く",
"2. ①に1完成品をWASHER BOLT で取付"
],
"WorkPoints": [
"取付目安1.25mm",
"矢印方向に押し当てて取付",
"取付場所2か所あり"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"Inspectio... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "9.8N･m",
"WorkName": "開閉ｶﾊﾞｰ組立16",
"WorkItems": [
"1. ①に②PLATE をBOLT WASHER で取付",
"2. 1完成品にMAGNET をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "開閉ｶﾊﾞｰ組立16",
"WorkItems": [
"1. ①に②PLATE をBOLT WASHER で取付",
"2. 1完成品にMAGNET をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1.8㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立16",
"WorkItems": [
"1. ①に②PLATE をBOLT WASHER で取付",
"2. 1完成品にMAGNET をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "取付位置確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "作業指示通り出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. ①を脱脂",
"2. 1完成品にLABEL LABEL LABEL を貼付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"この作業... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(開閉ｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6870",
"WorkName": "識別ﾗﾍﾞﾙ貼付け17連/34連(前側)",
"WorkItems": [
"1. ①を脱脂",
"2. 1完成品に㉗を取付けLABEL を貼付け"
],
"WorkPoints": [
"脱脂箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■... | {
"QualityItem": "貼付け確認",
"ToolManageNo": "FM-6870",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(開閉ｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6870",
"WorkName": "識別ﾗﾍﾞﾙ貼付け17連/34連・T/C切替(後側)",
"WorkItems": [],
"WorkPoints": [
"裏面㉗取付け規制位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "貼付け確認",
"ToolManageNo": "FM-6870",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立1",
"WorkItems": [
"1. BRACKET にBRACKET HINGE をBOLT WASHER NUT で取付"
],
"WorkPoints": [
"内曲げが取付け面になるように",
"ﾋﾝｼﾞとﾌﾞﾗｹｯﾄの上面を合わせて取付",
"ﾋﾝｼﾞはﾓﾝｷｰｽﾊﾟﾅで直角より､小さく曲げてから取付ける事",
"目安としてﾋﾝｼﾞからの出しろが1mmになるよう... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立1",
"WorkItems": [
"1. BRACKET にBRACKET HINGE をBOLT WASHER NUT で取付"
],
"WorkPoints": [
"内曲げが取付け面になるように",
"ﾋﾝｼﾞとﾌﾞﾗｹｯﾄの上面を合わせて取付",
"ﾋﾝｼﾞはﾓﾝｷｰｽﾊﾟﾅで直角より､小さく曲げてから取付ける事",
"目安としてﾋﾝｼﾞからの出しろが1mmになるように",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2",
"WorkItems": [
"■2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入",
"3. MONITOR に①をBOLT WASHER で取付",
"■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入"
],
"WorkPoints": [
"裏側",
"ﾓﾆﾀと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ2.0N･... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認、製造番号を転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2",
"WorkItems": [
"■2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入",
"3. MONITOR に①をBOLT WASHER で取付",
"■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入"
],
"WorkPoints": [
"裏側",
"ﾓﾆﾀと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ2.0N･... | {
"QualityItem": "検査書有無確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2",
"WorkItems": [
"■2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入",
"3. MONITOR に①をBOLT WASHER で取付",
"■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入"
],
"WorkPoints": [
"裏側",
"ﾓﾆﾀと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ2.0N･... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全てOFFの事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2",
"WorkItems": [
"■2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入",
"3. MONITOR に①をBOLT WASHER で取付",
"■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入"
],
"WorkPoints": [
"裏側",
"ﾓﾆﾀと平行に取付ける事"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立3",
"WorkItems": [
"1. COVER にLABEL LABEL を貼付",
"2. COVER にLABEL を貼付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙSW組立1",
"WorkItems": [
"■1. SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認",
"2. ①にSWITCH SWITCH SWITCH SWITCH を取付",
"3. ②にSWITCH を取付",
"4. 2完成品の裏面にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認、製造番号を転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙSW組立1",
"WorkItems": [
"■1. SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認",
"2. ①にSWITCH SWITCH SWITCH SWITCH を取付",
"3. ②にSWITCH を取付",
"4. 2完成品の裏面にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
... | {
"QualityItem": "ｽｲｯﾁ配置確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りｽｲｯﾁが配置されている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｲｯﾁ締付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5255",
"WorkName": "操作ﾊﾟﾈﾙSW組立1",
"WorkItems": [
"■1. SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認",
"2. ①にSWITCH SWITCH SWITCH SWITCH を取付"
],
"WorkPoints": [
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "FM-5255",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "FM-5255専用ﾋﾞｯﾄ",
"ToolOther": "147cN･m",
"WorkName": "操作ﾊﾟﾈﾙSW組立1",
"WorkItems": [
"3. ②にSWITCH を取付",
"4. 2完成品の裏面にCABLE-SUPPORT を取付",
"■1. SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認",
"2. ①にSWITCH SWITCH SWITCH SWITCH を取付"
],
"WorkPoints": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "125cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙSW組立2",
"WorkItems": [
"■1. ①②にPANEL SWITCH を取付"
],
"WorkPoints": [
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
"SW部",
"取付けﾘﾝｸﾞ",
"SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる",
"ﾊﾟﾈﾙ裏側",
"組み合わせに注意(F側･R側)",
"SWITCH ... | {
"QualityItem": "ｽｲｯﾁ配置確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りｽｲｯﾁが配置されている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "非常ｽｲｯﾁ締付工具",
"Size": "",
"ToolOther": "FM-5254",
"WorkName": "操作ﾊﾟﾈﾙSW組立2",
"WorkItems": [
"■1. ①②にPANEL SWITCH を取付"
],
"WorkPoints": [
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
"SW部",
"取付けﾘﾝｸﾞ",
"SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる",
"ﾊﾟﾈﾙ裏側",
"組み合わせに注意(F側･R側)... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "FM-5254",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "FM-5254専用ﾋﾞｯﾄ",
"ToolOther": "125cN･m",
"WorkName": "操作ﾊﾟﾈﾙSW組立2",
"WorkItems": [
"■1. ①②にPANEL SWITCH を取付"
],
"WorkPoints": [
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
"SW部",
"取付けﾘﾝｸﾞ",
"SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる",
"ﾊﾟﾈﾙ裏側",
"組み... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "125cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｲｯﾁ締付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5255",
"WorkName": "操作ﾊﾟﾈﾙSW組立2",
"WorkItems": [
"■1. ①②にPANEL SWITCH を取付"
],
"WorkPoints": [
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
"SW部",
"取付けﾘﾝｸﾞ",
"SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる",
"ﾊﾟﾈﾙ裏側",
"組み合わせに注意(F側･R側... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "FM-5255",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "FM-5255専用ﾋﾞｯﾄ",
"ToolOther": "147cN･m",
"WorkName": "操作ﾊﾟﾈﾙSW組立2",
"WorkItems": [
"■1. ①②にPANEL SWITCH を取付"
],
"WorkPoints": [
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
"SW部",
"取付けﾘﾝｸﾞ",
"SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる",
"ﾊﾟﾈﾙ裏側",
"組み... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "147cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙSW配線処理",
"WorkItems": [
"1. ①②にOPERATION PARTS WIRING: NPM-GH を接続しｲﾝｼｭﾛｯｸで固定"
],
"WorkPoints": [
"STOP",
"EXCH",
"SERVO",
"START",
"ｺﾈｸﾀﾌﾞﾗｹｯﾄに取付ける",
"F側､R側に区別されているので注意",
"START､STOP､SERVO",
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立1",
"WorkItems": [
"■1. FAN の型式ﾁｪｯｸをし､ｼﾘｱﾙNo.を検査表に記入",
"2. 1完成品にFAN-GUARD をSPACER BOLT WASHER WASHER で取付"
],
"WorkPoints": [
"型式確認",
"ｼﾘｱﾙ確認",
"F側､R側に区別しておく",
"ﾌｧﾝｶﾞｰﾄﾞの取付方向に注意すること",
"風向き方向を確認して取付"
... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認、製造番号を転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "152cN･m",
"WorkName": "FAN組立1",
"WorkItems": [
"■1. FAN の型式ﾁｪｯｸをし､ｼﾘｱﾙNo.を検査表に記入",
"2. 1完成品にFAN-GUARD をSPACER BOLT WASHER WASHER で取付"
],
"WorkPoints": [
"型式確認",
"ｼﾘｱﾙ確認",
"F側､R側に区別しておく",
"ﾌｧﾝｶﾞｰﾄﾞの取付方向に注意すること",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "152cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立2",
"WorkItems": [
"1. LABEL から【G103R】【G104R】を切り取り､①②のｺﾈｸﾀｰに貼付ける"
],
"WorkPoints": [
"Front用",
"Rear用",
"LABELは1工程前準備より貰いうける事",
"組み合わせに注意(F側･R側)",
"Front用FANに【G103R】､Rear用FANに【G104R】を貼付ける"
],
"Tolk... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "FAN組立3",
"WorkItems": [
"1. ①にCOVER をBOLT WASHER で取付"
],
"WorkPoints": [
"取付方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "FAN組立3",
"WorkItems": [
"2. CATCH をBRACKET にBOLT で取付"
],
"WorkPoints": [
"CATCH はﾍﾞｰｽ側を使用ﾎﾞﾃﾞｨ側は次作業で使用",
"ﾒｽ側"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯｸﾀｲﾄ",
"Size": "",
"ToolOther": "243",
"WorkName": "FAN組立4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"▲1. ①に②を③⑥で取付",
"2. 1完成品に④⑤を取... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"作業者安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "FAN組立4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"▲1. ①に②を③⑥で取付",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "FAN組立4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"◆作業者安全作業",
"●クリーン作業"
],
"Words": [
"10㎜",
"3㎜",
"3㎜",
"6... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "FAN組立5",
"WorkItems": [
"1. COVER にBRACKET をWASHER BOLT で取付",
"2. 1完成品にCOVER をBOLT WASHER で仮止め"
],
"WorkPoints": [
"面一で取付",
"SD-A038963-047で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "FAN組立5",
"WorkItems": [
"1. COVER にBRACKET をWASHER BOLT で取付",
"2. 1完成品にCOVER をBOLT WASHER で仮止め"
],
"WorkPoints": [
"面一で取付",
"SD-A038963-047で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Fan-FilterGuideAssemblyJig",
"Size": "",
"ToolOther": "FM-6317",
"WorkName": "FAN組立5",
"WorkItems": [
"1. COVER にBRACKET をWASHER BOLT で取付",
"2. 1完成品にCOVER をBOLT WASHER で仮止め"
],
"WorkPoints": [
"面一で取付",
"SD-A038963-047で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6317",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "FAN組立6",
"WorkItems": [
"1. ①にPLATE をBOLT で取付",
"3. 2完成品にCOVER COVER COVER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "FAN組立6",
"WorkItems": [
"2. 1完成品にSPACER をBOLT WASHER で取付"
],
"WorkPoints": [
"面一になるよう取付",
"中心に取付"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "10㎜",
"ToolOther": "",
"WorkName": "FAN組立7",
"WorkItems": [
"1. ①に②をBOLT WASHER で仮止め",
"2. 1完成品に③をｾｯﾄし位置調整をする"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞを置く"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全... | {
"QualityItem": "取付位置確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "作業指示通り出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "FAN組立7",
"WorkItems": [
"1. ①に②をBOLT WASHER で仮止め",
"2. 1完成品に③をｾｯﾄし位置調整をする"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞを置く"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "FAN組立7",
"WorkItems": [
"1. ①に②をBOLT WASHER で仮止め",
"2. 1完成品に③をｾｯﾄし位置調整をする"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞを置く"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Fan-FilterGuideAssemblyJig",
"Size": "",
"ToolOther": "FM-6317",
"WorkName": "FAN組立7",
"WorkItems": [
"1. ①に②をBOLT WASHER で仮止め",
"2. 1完成品に③をｾｯﾄし位置調整をする"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞを置く",
"平行",
"③ｶﾊﾞｰを被せ調整",
"調整後③ｶﾊﾞｰは外しておくこと"
],
"Tolks": [
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6317",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯｸﾀｲﾄ",
"Size": "",
"ToolOther": "243",
"WorkName": "FAN組立8",
"WorkItems": [
"◆1. ①にFAN-GUARD ④をBOLT WASHER WASHER WASHER で取付"
],
"WorkPoints": [
"ﾌｧﾝｶﾞｰﾄﾞの方向に注意",
"WASHER ﾎﾞﾙﾄに接着剤塗布"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "FAN組立8",
"WorkItems": [
"◆1. ①にFAN-GUARD ④をBOLT WASHER WASHER WASHER で取付"
],
"WorkPoints": [
"ﾌｧﾝｶﾞｰﾄﾞの方向に注意",
"WASHER ﾎﾞﾙﾄに接着剤塗布"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "SDｶｰﾄﾞﾘｰﾀﾞ組立",
"WorkItems": [
"2. BRACKET に1完成品をBOLT WASHER で取付",
"■1. CARD-READER の型式確認､ｼﾘｱﾙNo.を検査表に記入",
"3. 2完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"型式表示が上面になるように",
"取付け方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 1... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認、製造番号を転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "SDｶｰﾄﾞﾘｰﾀﾞ組立",
"WorkItems": [
"2. BRACKET に1完成品をBOLT WASHER で取付",
"■1. CARD-READER の型式確認､ｼﾘｱﾙNo.を検査表に記入",
"3. 2完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"型式表示が上面になるように",
"取付け方向注意"
],
"Tolks":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "100cN･m",
"WorkName": "SDｶｰﾄﾞﾘｰﾀﾞ組立",
"WorkItems": [
"2. BRACKET に1完成品をBOLT WASHER で取付",
"■1. CARD-READER の型式確認､ｼﾘｱﾙNo.を検査表に記入",
"3. 2完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"型式表示が上面になるように",
"取付け方向注意"
],
"Tolks... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "A002・003ｶﾊﾞｰ組立",
"WorkItems": [
"1. COVER COVER にBRACKET BRACKET をBOLT WASHER で取付",
"2. 1完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"F側",
"R側",
"矢印方向に押し当て取付",
"端面を合わせて取付"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "27㎜",
"ToolOther": "3.5N･m",
"WorkName": "A002・003ｶﾊﾞｰ組立(配線ﾌﾞﾗｹｯﾄ)",
"WorkItems": [
"1. ①②にSIGNAL-TOWER を取付"
],
"WorkPoints": [
"正面からｼｰﾙが見えないように取付",
"ﾊﾟｯｷﾝはｶﾊﾞｰ表面側",
"ﾜｯｼｬｰはｶﾊﾞｰ裏面側"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "A002・003ｶﾊﾞｰ組立(FAN)1",
"WorkItems": [
"1. ①②に③④をSCREW で取付",
"2. 1完成品の配線をｲﾝｼｭﾛｯｸで固定"
],
"WorkPoints": [
"FAN取付け方向に注意",
"組み合わせに注意(F側･R側)",
"FAN取付け方向",
"板金が前を向くこと"
],
"Tolks": [
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "A002・003ｶﾊﾞｰ組立(FAN)1",
"WorkItems": [],
"WorkPoints": [
"長いｹｰﾌﾞﾙ(P2XXR)を1周させて､ｹｰﾌﾞﾙ先端ﾁｭｰﾌﾞを揃え､そこから30㎜で固定｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "A002・003ｶﾊﾞｰ組立(FAN)2",
"WorkItems": [
"1. ①②に③④を⑯⑰で取付"
],
"WorkPoints": [
"組み合わせに注意(F側･R側)"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "A002・003ｶﾊﾞｰ組立(FAN)2",
"WorkItems": [
"1. ①②に③④を⑯⑰で取付"
],
"WorkPoints": [
"組み合わせに注意(F側･R側)"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "A002ｶﾊﾞｰ組立(SD)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"カバー開口部中心に㉘を差込み抜き差し確認を行う",
"取付け詳細",
"BUS... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "A002・004ｶﾊﾞｰ組立(開閉扉ｽﾄｯﾊﾟｰ)",
"WorkItems": [
"1. ①COVER に③をBOLT WASHER で取付",
"2. 1完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取付け位置",
"横向き方向の長穴を取付け面にする"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "A002・004ｶﾊﾞｰ組立(開閉扉ｽﾄｯﾊﾟｰ)",
"WorkItems": [
"1. ①COVER に③をBOLT WASHER で取付",
"2. 1完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取付け位置",
"横向き方向の長穴を取付け面にする"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "A002・004ｶﾊﾞｰ組立(開閉扉ｽﾄｯﾊﾟｰ)",
"WorkItems": [
"1. ①COVER に③をBOLT WASHER で取付",
"2. 1完成品にBRACKET をBOLT WASHER で取付",
"1. ①COVER に③をBOLT WASHER で取付",
"2. 1完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取付け位置",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "A002ｶﾊﾞｰ銘板貼付け1",
"WorkItems": [
"1. ①にLABEL を貼付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"51.5mm",
"122mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "A002ｶﾊﾞｰ銘板貼付け2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"35mm",
"103mm",
"141.5mm",
"5mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "A003・A005組立(開閉扉ｽﾄｯﾊﾟｰ)ﾌｨｰﾀﾞ仕様",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"締付ﾄﾙｸ 3.6N･m",
"取付け方向注意",
"締付... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "A003・A005組立(開閉扉ｽﾄｯﾊﾟｰ)ﾌｨｰﾀﾞ仕様",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"締付ﾄﾙｸ 3.6N･m",
"取付け方向注意",
"締付... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.