input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "GWEHD-F013-002",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"GWEHD-F013-002"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "GWEHD-F013-002",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"GWEHD-F013-002"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管⑤",
"WorkItems": [
"1. ②に①CABLE を接続"
],
"WorkPoints": [
"NP9~16",
"NP9~16",
"NP1~8",
"2を接続",
"5を接続"
],
"Tolks": [],
"InspectionNo": "GWEHD-F013-002",
"InspectionItems": [
"検査表①:3-... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立①",
"WorkItems": [
"1. SPRING 端部の輪を引っ掛け､ﾘﾝｸﾞ状にする",
"◆2. CLAMP-ARM 先端部のｸﾞﾘｰｽ溝へｸﾞﾘｰｽを塗布する",
"4. NOZZLE HOLDER を㉚治具にｾｯﾄする",
"◆3. 2の完成品を㉙治具 にセットし、グリスを塗布する",
"◆5. 4の完成品の指定箇所にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽFM-5718",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立①",
"WorkItems": [
"4. NOZZLE HOLDER を㉚治具にｾｯﾄする",
"◆3. 2の完成品を㉙治具 にセットし、グリスを塗布する"
],
"WorkPoints": [
"･注射器でｸﾗﾝﾌﾟ幅に塗布 (ｺﾞﾏ粒/1粒)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞ組立治具",
"Size": "",
"ToolOther": "FM-5761",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立①",
"WorkItems": [
"◆5. 4の完成品の指定箇所にｸﾞﾘｰｽを塗布する",
"◆5. 4の完成品の指定箇所にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"図の通りにｾｯﾄする",
"図の通りにｾｯﾄする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5761",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞ組立治具",
"Size": "",
"ToolOther": "FM-5761",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立②",
"WorkItems": [
"1. ③に上部治具をｾｯﾄする",
"2. ②を挿入し､治具をｾｯﾄする",
"3. 2の完成品に治具㉘を取付、①を組み込む",
"1. ③に上部治具をｾｯﾄする",
"2. ②を挿入し､治具をｾｯﾄする",
"3. 2の完成品に治具㉘を取付、①を組み込む",
"1. ③に上部治具をｾｯﾄする",
"2. ②... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5761",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.5㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立②",
"WorkItems": [
"1. ③に上部治具をｾｯﾄする",
"2. ②を挿入し､治具をｾｯﾄする",
"3. 2の完成品に治具㉘を取付、①を組み込む",
"1. ③に上部治具をｾｯﾄする",
"2. ②を挿入し､治具をｾｯﾄする",
"3. 2の完成品に治具㉘を取付、①を組み込む"
],
"WorkPoints": [
"②が歪み無く取付ら... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ準備治具",
"Size": "",
"ToolOther": "FM-1855",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立②",
"WorkItems": [
"1. ③に上部治具をｾｯﾄする",
"2. ②を挿入し､治具をｾｯﾄする",
"3. 2の完成品に治具㉘を取付、①を組み込む"
],
"WorkPoints": [
"②が歪み無く取付られ､ｽﾑｰｽﾞに動くことを確認する",
"ｸﾞﾘｰｽ溝を上側に向けｾｯﾄ",
"隙間0.5mm程度",
"隙間0.5mm... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1855",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "4㎜幅",
"ToolOther": "10cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立③",
"WorkItems": [
"1. ③にFILTER を取付",
"2. 1の完成品にSPRING を取付"
],
"WorkPoints": [
"精密ﾄﾞﾗｲﾊﾞｰは使用しないこと",
"SPRING の取付に異常がないか確認する",
"SPRING がﾋﾟﾝの下にあること",
"SPRING の先端がﾈｼﾞﾚていないこと"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞ組立治具",
"Size": "",
"ToolOther": "FM-5761",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立③",
"WorkItems": [
"1. ③にFILTER を取付",
"2. 1の完成品にSPRING を取付"
],
"WorkPoints": [
"精密ﾄﾞﾗｲﾊﾞｰは使用しないこと",
"SPRING の取付に異常がないか確認する",
"SPRING がﾋﾟﾝの下にあること",
"SPRING の先端がﾈｼﾞﾚていないこと"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5761",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "95cN･m",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾅｰ組立",
"WorkItems": [
"1. BLOCK に油砥石をかける",
"2. 1の完成品にBOLT COLLAR BEARING を取付"
],
"WorkPoints": [
"全面にﾊﾞﾘ､異物等無き事",
"BOLT 締付後､BEARING の回転がなめらかである事を確認",
"FM-6440 治具使用例"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄﾃﾝｼｮﾅｰ組立治具",
"Size": "",
"ToolOther": "FM-6440",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾅｰ組立",
"WorkItems": [
"1. BLOCK に油砥石をかける",
"2. 1の完成品にBOLT COLLAR BEARING を取付"
],
"WorkPoints": [
"全面にﾊﾞﾘ､異物等無き事",
"BOLT 締付後､BEARING の回転がなめらかである事を確認",
"FM-6440 治具使用例"
],
"Tolks": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6440",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾗｲﾝ組立①",
"WorkItems": [
"1. BALL-SPLINE のｼﾘｱﾙ番号記入"
],
"WorkPoints": [
"ｽﾌﾟﾗｲﾝ外筒",
"ｽﾌﾟﾗｲﾝ軸",
"16本のﾎﾞｰﾙｽﾌﾟﾗｲﾝをｼﾘｱﾙNo｡の若い順に並べ､軸と外筒を紐付け出来る様にしておく",
"軸全体の防錆油を拭き取る"
],
"Tolks": [],
"InspectionNo": "GWEHD-F01... | {
"QualityItem": "ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾗｲﾝ組立①",
"WorkItems": [
"1. BALL-SPLINE のｼﾘｱﾙ番号記入"
],
"WorkPoints": [
"ｽﾌﾟﾗｲﾝ外筒",
"ｽﾌﾟﾗｲﾝ軸",
"16本のﾎﾞｰﾙｽﾌﾟﾗｲﾝをｼﾘｱﾙNo｡の若い順に並べ､軸と外筒を紐付け出来る様にしておく",
"軸全体の防錆油を拭き取る"
],
"Tolks": [],
"InspectionNo": "GWEHD-F01... | {
"QualityItem": "防錆油拭取り確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り拭取り出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｳｼﾞﾝｸﾞﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-5709",
"WorkName": "ｽﾌﾟﾗｲﾝ組立②",
"WorkItems": [
"2. HOUSING の摺動面に油砥石をかける",
"1. BEARING にPIN を圧入",
"◆3. 1.完成品に2.完成品を圧入"
],
"WorkPoints": [
"下面",
"ﾋﾟﾝ方向なし",
"16個",
"16個",
"㉖プレートＡにBEARING を置き、㉖プレートＢで蓋をし... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5709",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾗｲﾝ組立②",
"WorkItems": [
"2. HOUSING の摺動面に油砥石をかける",
"1. BEARING にPIN を圧入",
"◆3. 1.完成品に2.完成品を圧入"
],
"WorkPoints": [
"下面",
"ﾋﾟﾝ方向なし",
"16個",
"16個",
"㉖プレートＡにBEARING を置き、㉖プレートＢで蓋をして、穴にPIN を挿入して圧入後、㉖プレ... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾐ､埃が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Yﾊﾟｯｷﾝｽﾀﾝﾄﾞｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6126",
"WorkName": "ｽﾌﾟﾗｲﾝ組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"2. 治具にPACKING を挿入する",
"◆1. 治具にｸﾞﾘｰｽを塗布する",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6126",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾗｲﾝ組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"検査表①:8 Yﾊﾟｯｷﾝの組立",
"･PACKING の溝面側が①の外側に来るよう... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾗｲﾝ組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"検査表①:8 Yﾊﾟｯｷﾝの組立",
"･PACKING の溝面側が①の外側に来るよう... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒幅長",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Yﾊﾟｯｷﾝ挿入治具",
"Size": "",
"ToolOther": "FM-5795",
"WorkName": "ｽﾌﾟﾗｲﾝ組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"検査表①:8 Yﾊﾟｯｷﾝの組立",
"･PACKIN... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5795",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾗｲﾝ組立④",
"WorkItems": [
"1. ②にBEARING を挿入",
"◆2. １完成品を㉗へ挿入",
"4. 3完成品へBEARING HOLDER を挿入し､PIECE SCREW で仮固定",
"3. 2完成品へ①を挿入"
],
"WorkPoints": [
"BEARING は1個のみ挿入する",
"治具を②へ挿入",
"治具へｸﾞﾘｰｽを塗布し全体へ均等にのばす",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｳｼﾞﾝｸﾞYﾊﾟｯｷﾝ案内治具",
"Size": "",
"ToolOther": "FM-1860",
"WorkName": "ｽﾌﾟﾗｲﾝ組立④",
"WorkItems": [
"1. ②にBEARING を挿入",
"◆2. １完成品を㉗へ挿入",
"3. 2完成品へ①を挿入"
],
"WorkPoints": [
"BEARING は1個のみ挿入する",
"この作業では同じものを16個製作",
"真空穴にｸﾞﾘｰｽが入らないよう､点塗布し外周に均一にのばす"
],
"Tol... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1860",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸組立①",
"WorkItems": [
"◆1. BRACKET に油砥石をかける"
],
"WorkPoints": [
"上面",
"前面",
"後面",
"下面",
"上面",
"後面",
"前面",
"下面",
"･ｴｱｰｶﾞﾝにて研磨面のｺﾞﾐ､ｶｽ等を除去する･油砥石にて､研磨面にﾊﾞﾘ･打痕等の突起がないか確認し､ｱﾙｺｰﾙで清掃する",
"･... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾐ､埃が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "上部ﾍﾞｱﾘﾝｸﾞ圧入治具",
"Size": "",
"ToolOther": "FM-5724",
"WorkName": "θ軸組立②",
"WorkItems": [
"1. ①にBEARING を圧入"
],
"WorkPoints": [
"BEARING は面一まで圧入する事",
"PLATE の裏表に注意(面取りがある方が上にする)",
"治具使用ｲﾒｰｼﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5724",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "100cN･m",
"WorkName": "θ軸組立②",
"WorkItems": [
"2. 1の完成品にPLATE をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Dﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-5719",
"WorkName": "θ軸組立③",
"WorkItems": [
"1. ①にPIN PIN を圧入",
"2. 1の完成品に②を挿入"
],
"WorkPoints": [
"②の挿入方向に注意(下図参照)",
"矢視",
"出代3mm",
"ﾃｰﾊﾟ側を圧入",
"PIN PIN の圧入方向に注意(下図参照)",
"圧入場所は下図参照",
"ﾉｽﾞﾙﾎﾟｼﾞｼｮﾝ(NP)... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5719",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸組立③",
"WorkItems": [
"1. ①にPIN PIN を圧入",
"2. 1の完成品に②を挿入"
],
"WorkPoints": [
"②の挿入方向に注意(下図参照)",
"矢視",
"出代3mm",
"ﾃｰﾊﾟ側を圧入",
"PIN PIN の圧入方向に注意(下図参照)",
"圧入場所は下図参照",
"ﾉｽﾞﾙﾎﾟｼﾞｼｮﾝ(NP)配置は(下図 ... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入治具",
"Size": "",
"ToolOther": "FM-3237",
"WorkName": "θ軸組立④",
"WorkItems": [
"1. ①にBEARING を圧入"
],
"WorkPoints": [
"ｽﾌﾟﾗｲﾝ外筒を指で矢印方回し､引掛りがないことを確認する"
],
"Tolks": [],
"InspectionNo": "GWEHD-F013-001",
"InspectionItems": [
"検査表①:ﾎﾞｰﾙｽﾌﾟﾗｲﾝΘ方向回転確認"
]... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3237",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "なめらかな回転である事",
"Method": "手感",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾞｰﾙｽﾌﾟﾗｲﾝ圧入台",
"Size": "",
"ToolOther": "FM-5777",
"WorkName": "θ軸組立④",
"WorkItems": [
"1. ①にBEARING を圧入"
],
"WorkPoints": [
"ｽﾌﾟﾗｲﾝ外筒を指で矢印方回し､引掛りがないことを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5777",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "なめらかな回転である事",
"Method": "手感",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟｰﾘｰﾅｯﾄ締付治具",
"Size": "",
"ToolOther": "FM-5597",
"WorkName": "θ軸組立⑤",
"WorkItems": [
"1. ①に治具を取付"
],
"WorkPoints": [
"Hｶｯﾄの向きが揃っていないと治具に取付出来ない為",
"ｽﾌﾟﾗｲﾝ外筒のｼﾘｱﾙNo.が前後面共に左向きに揃える",
"Hｶｯﾄの向きが揃っている状態で治具に取付はめ込んでから治具内蔵BOLT(右図矢印)で固定する",
"Hｶｯﾄの向きが揃っていない状態で治具に取付るとHｶ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5597",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸組立⑤",
"WorkItems": [
"1. ①に治具を取付"
],
"WorkPoints": [
"Hｶｯﾄの向きが揃っていないと治具に取付出来ない為",
"ｽﾌﾟﾗｲﾝ外筒のｼﾘｱﾙNo.が前後面共に左向きに揃える",
"Hｶｯﾄの向きが揃っている状態で治具に取付はめ込んでから治具内蔵BOLT(右図矢印)で固定する",
"Hｶｯﾄの向きが揃っていない状態で治具に取付るとHｶｯﾄ部が破損します",... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸組立⑥",
"WorkItems": [
"1. ①にCOLLAR PULLEY COLLAR COLLAR BEARING NUT をPos1,3,7,10,14,16に取付"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"COLLAR COLLAR の方向に注意(下図参照)",
"NUT は締結しない"
],
"Tolks": [],
"InspectionNo":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸組立⑦",
"WorkItems": [
"1. ①にCOLLAR BEARING COLLAR PULLEY COLLAR NUT をPos2,6,8,9,11,15に取付"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"NUT は締結しない",
"COLLAR の方向に注意(下図参照)"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸組立⑧",
"WorkItems": [
"1. ①にCOLLAR PULLEY COLLAR COLLAR NUT をPos4,13に取付"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"NUT は締結しない",
"COLLAR COLLAR の方向に注意(下図参照)"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽﾌﾟﾗｲﾝ締付けｱﾀｯﾁﾒﾝﾄ",
"Size": "",
"ToolOther": "FM-3030",
"WorkName": "θ軸組立⑨",
"WorkItems": [
"1. ①にCOLLAR COLLAR PULLEY COLLAR NUT をPos5,12に取付",
"2. ﾍﾞｱﾘﾝｸﾞ回転確認"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"NUT は締結しない",
"COLLAR COLLAR の方向に注意(下図参照)",
"全PosのN... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3030",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｺﾝﾍﾞｱ･配線等の干渉無い事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "2.0N･m",
"WorkName": "θ軸組立⑨",
"WorkItems": [
"1. ①にCOLLAR COLLAR PULLEY COLLAR NUT をPos5,12に取付",
"2. ﾍﾞｱﾘﾝｸﾞ回転確認"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"NUT は締結しない",
"COLLAR COLLAR の方向に注意(下図参照)",
"全PosのNUTを締付を実施｡その... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸組立⑨",
"WorkItems": [
"1. ①にCOLLAR COLLAR PULLEY COLLAR NUT をPos5,12に取付",
"2. ﾍﾞｱﾘﾝｸﾞ回転確認"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"NUT は締結しない",
"COLLAR COLLAR の方向に注意(下図参照)",
"全PosのNUTを締付を実施｡その後各Posのﾍﾞｱﾘﾝ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸ﾌﾟｰﾘ組立",
"WorkItems": [
"▲1. PULLEY に接着剤を塗布",
"2. 1の完成品にCOLLAR COLLAR を圧入"
],
"WorkPoints": [
"COLLAR COLLAR の圧入方向に注意(下図参照)",
"COLLAR COLLAR を確実に着底させる事(下図参照)",
"余分な接着剤は除去する事",
"この作業では同じものを2個製作",
"指定箇所へ... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ638",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞﾙﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ﾍﾞﾙﾄの印字が上下逆さまにならない様にする事",
"上段のﾍﾞﾙﾄを指示通りに引き回す",
"下... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽﾌﾟﾗｲﾝ締付けｱﾀｯﾁﾒﾝﾄ",
"Size": "",
"ToolOther": "FM-3030",
"WorkName": "ﾍﾞﾙﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ﾍﾞﾙﾄの印字が上下逆さまにならない様にする事",
"上段のﾍﾞ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3030",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｺﾝﾍﾞｱ･配線等の干渉無い事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "2.0N･m",
"WorkName": "ﾍﾞﾙﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ﾍﾞﾙﾄの印字が上下逆さまにならない様にする事",
"上段のﾍﾞﾙﾄを指示通りに引き回... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞﾙﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ﾍﾞﾙﾄの印字が上下逆さまにならない様にする事",
"上段のﾍﾞﾙﾄを指示通りに引き回す",
"下... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "なめらかな回転である事",
"Method": "手感",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾅｰ取付",
"WorkItems": [
"1. ①に②をBOLT BOLT WASHER で取付け"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"仮止め､ﾃﾝｼｮﾝも緩めにする",
"ﾃﾝｼｮﾅｰ取付後､治具FM-5597より製品を取外す※ﾃﾝｼｮﾝは緩めの状態"
],
"Tolks": [],
"InspectionNo": "",
"Insp... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "80cN･m",
"WorkName": "θﾌﾟｰﾘ部ｷﾞﾔ取付",
"WorkItems": [
"1. ①にGEAR をSHAFT で締結"
],
"WorkPoints": [
"ﾌﾟｰﾘｰの反対側から-ﾄﾞﾗｲﾊﾞｰで回り止めを行いながらSHAFT を締結する"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θﾌﾟｰﾘ部ｷﾞﾔ取付",
"WorkItems": [
"◆2. GEAR ｷﾞﾔにｸﾞﾘｰｽを塗布",
"1. ①にGEAR をSHAFT で締結"
],
"WorkPoints": [
"ﾌﾟｰﾘｰの反対側から-ﾄﾞﾗｲﾊﾞｰで回り止めを行いながらSHAFT を締結する",
"指示箇所全周均一に塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"Inspection... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.0",
"ToolOther": "10cN･m",
"WorkName": "ｾﾝｻｰｷﾞｱ部組立",
"WorkItems": [
"▲1. GEAR にBEARING をSCREW で締結"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"SCREW にﾛｯｸﾀｲﾄを塗布して締結",
"SCREW にﾛｯｸﾀｲﾄを塗布する量は3本合計でｺﾞﾏ粒1のこと",
"締結後､余分な接着剤は拭き取ること"
],
"Tolks"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰｷﾞｱ部組立",
"WorkItems": [
"▲1. GEAR にBEARING をSCREW で締結"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"SCREW にﾛｯｸﾀｲﾄを塗布して締結",
"SCREW にﾛｯｸﾀｲﾄを塗布する量は3本合計でｺﾞﾏ粒1のこと",
"締結後､余分な接着剤は拭き取ること"
],
"Tolks": [
"締付ﾄﾙｸ 10c... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ242",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "U-507",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整",
"WorkItems": [
"1. ①のΘ駆動ﾍﾞﾙﾄﾃﾝｼｮﾝの調整を行う"
],
"WorkPoints": [
"測定箇所は下図●にて測定",
"測定箇所のﾃﾝｼｮﾅｰにて調整する(下図参照)",
"A上ﾍﾞﾙﾄ(Pos13~16)",
"A下ﾍﾞﾙﾄ(Pos5~8)",
"B上ﾍﾞﾙﾄ(Pos1~4)",
"B下ﾍﾞﾙﾄ(Pos9~12)",
... | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "最大値≦19N最小値≧9N12≦平均値≦16",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "張力計治具",
"Size": "",
"ToolOther": "FM-5690",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整",
"WorkItems": [
"1. ①のΘ駆動ﾍﾞﾙﾄﾃﾝｼｮﾝの調整を行う"
],
"WorkPoints": [
"測定箇所は下図●にて測定",
"測定箇所のﾃﾝｼｮﾅｰにて調整する(下図参照)",
"A上ﾍﾞﾙﾄ(Pos13~16)",
"A下ﾍﾞﾙﾄ(Pos5~8)",
"B上ﾍﾞﾙﾄ(Pos1~4)",
"B下ﾍﾞﾙﾄ(Pos9~12)",
... | {
"QualityItem": "張力確認",
"ToolManageNo": "FM-5690",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "最大値≦19N最小値≧9N12≦平均値≦16",
"Method": "張力計治具",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整",
"WorkItems": [
"1. ①のΘ駆動ﾍﾞﾙﾄﾃﾝｼｮﾝの調整を行う"
],
"WorkPoints": [
"測定箇所は下図●にて測定",
"測定箇所のﾃﾝｼｮﾅｰにて調整する(下図参照)",
"A上ﾍﾞﾙﾄ(Pos13~16)",
"A下ﾍﾞﾙﾄ(Pos5~8)",
"B上ﾍﾞﾙﾄ(Pos1~4)",
"B下ﾍﾞﾙﾄ(Po... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｾﾝｻｰｷﾞﾔ取付",
"WorkItems": [
"1. ①に②をCOLLAR BOLT で締結"
],
"WorkPoints": [
"ｽﾌﾟﾗｲﾝ外筒のｼﾘｱﾙNo.を前面･後面共に正面に向ける(以後､この位置をｷｰﾌﾟする)",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ調整時に各軸が若干ｽﾞﾚますが問題ありません"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰｷﾞﾔ取付",
"WorkItems": [
"1. ①に②をCOLLAR BOLT で締結",
"◆2. ②の全周にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"②の取付方向に注意(下図参照)",
"前面(1~8)",
"後面(9~16)",
"ｽﾌﾟﾗｲﾝ外筒のｼﾘｱﾙNo.を前面･後面共に正面に向ける(以後､この位置をｷｰﾌﾟする)",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ調整時に各軸が... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ｾﾝｻｰ取付",
"WorkItems": [
"1. ①にSENSOR(165MM) SENSOR(80MM) をBOLT WASHER WASHER で締結"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "θﾓｰﾀ取付①",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"指示通りに取付(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θﾓｰﾀ取付①",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"指示通りに取付(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θﾓｰﾀ取付②",
"WorkItems": [
"■1. ①にMOTOR をWASHER ⑰で仮固定"
],
"WorkPoints": [
"Θ1軸(1~4)(9~12)",
"Θ2軸(5~8)(13~16)",
"矢視",
"仮止め:SD-A0035434-048にて本締め"
],
"Tolks": [],
"InspectionNo": "GWEHD-F013-001",
"Inspecti... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θﾓｰﾀ取付②",
"WorkItems": [
"■1. ①にMOTOR をWASHER ⑰で仮固定"
],
"WorkPoints": [
"Θ1軸(1~4)(9~12)",
"Θ2軸(5~8)(13~16)",
"矢視",
"仮止め:SD-A0035434-048にて本締め"
],
"Tolks": [],
"InspectionNo": "GWEHD-F013-001",
"Inspecti... | {
"QualityItem": "ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "θﾓｰﾀ取付③",
"WorkItems": [
"1. ①のﾓｰﾀを締結",
"2.COUPLING BOLT を仮締結"
],
"WorkPoints": [
"COUPLING の取付方向に注意(下図参照)",
"COUPLING にてﾓｰﾀとﾌﾟｰﾘｰの芯出しを行ってからﾓｰﾀを締結する"
],
"Tolks": [],
"InspectionNo": "",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θﾓｰﾀ取付③",
"WorkItems": [
"3. 2の完成品にCABLE を取付"
],
"WorkPoints": [
"CABLE の取付位置､向きは下図参照",
"動力線(太い)",
"ｴﾝｺｰﾀﾞ線(細い)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸組立⑩",
"WorkItems": [
"◆1. PLATE にｸﾞﾘｰｽを塗布",
"2. 1の完成品を①へBOLT で仮固定､PLATE をBOLT WASHER で仮固定"
],
"WorkPoints": [
"PLATE のﾃｰﾊﾟ側を①側に向けて取付",
"ﾍﾞｱﾘﾝｸﾞ転がり面とﾊｳｼﾞﾝｸﾞ摺動面にｸﾞﾘｰｽと塗布※上図はﾌﾟﾚｰﾄの一部を抜粋",
"C 面取りをΘ1軸方面に向けて取付",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆粒:各1",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "θ軸組立⑪",
"WorkItems": [
"1. ①に②を挿入",
"2. 1の完成品の整定板をずらす"
],
"WorkPoints": [
"･ｽﾌﾟﾗｲﾝ外筒と②のｼﾘｱﾙNo.向きと番号を合わせて挿入する",
"整定板をずらした後でｽﾌﾟﾗｲﾝｼｬﾌﾄの摺動を確認する"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "θ軸組立⑪",
"WorkItems": [
"1. ①に②を挿入",
"2. 1の完成品の整定板をずらす"
],
"WorkPoints": [
"･ｽﾌﾟﾗｲﾝ外筒と②のｼﾘｱﾙNo.向きと番号を合わせて挿入する",
"整定板をずらした後でｽﾌﾟﾗｲﾝｼｬﾌﾄの摺動を確認する"
],
"Tolks": [],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "θ軸組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5811",
"WorkName": "θ軸組立⑪",
"WorkItems": [
"1. ①に②を挿入",
"2. 1の完成品の整定板をずらす"
],
"WorkPoints": [
"･ｽﾌﾟﾗｲﾝ外筒と②のｼﾘｱﾙNo.向きと番号を合わせて挿入する",
"整定板をずらした後でｽﾌﾟﾗｲﾝｼｬﾌﾄの摺動を確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5811",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "整定板予圧治具",
"Size": "",
"ToolOther": "FM-5732",
"WorkName": "θ軸組立⑪",
"WorkItems": [
"1. ①に②を挿入",
"2. 1の完成品の整定板をずらす"
],
"WorkPoints": [
"･ｽﾌﾟﾗｲﾝ外筒と②のｼﾘｱﾙNo.向きと番号を合わせて挿入する",
"整定板をずらした後でｽﾌﾟﾗｲﾝｼｬﾌﾄの摺動を確認する"
],
"Tolks": [],
"InspectionNo": "GWEHD-F013-001",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5732",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "0.5N",
"ToolOther": "",
"WorkName": "θ軸組立⑪",
"WorkItems": [
"1. ①に②を挿入",
"2. 1の完成品の整定板をずらす"
],
"WorkPoints": [
"･ｽﾌﾟﾗｲﾝ外筒と②のｼﾘｱﾙNo.向きと番号を合わせて挿入する",
"整定板をずらした後でｽﾌﾟﾗｲﾝｼｬﾌﾄの摺動を確認する"
],
"Tolks": [],
"InspectionNo": "GWEHD-F013-001",
... | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "0.8N以下",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "0.001m",
"ToolOther": "",
"WorkName": "θ軸組立⑪",
"WorkItems": [
"1. ①に②を挿入",
"2. 1の完成品の整定板をずらす"
],
"WorkPoints": [
"･ｽﾌﾟﾗｲﾝ外筒と②のｼﾘｱﾙNo.向きと番号を合わせて挿入する",
"整定板をずらした後でｽﾌﾟﾗｲﾝｼｬﾌﾄの摺動を確認する"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "20(0~+1)μm",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸組立⑫",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"締付ﾄﾙｸ 80cN･m",
"COLLAR の挿入方向に注意(下図参照)",
"内径が大きい方をｼｬﾌﾄ側に挿入する",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜BOX",
"ToolOther": "80cN･m",
"WorkName": "θ軸組立⑫",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"締付ﾄﾙｸ 80cN･m",
"COLLAR の挿入方向に注意(下図参照)",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽﾌﾟﾗｲﾝｼｬﾌﾄ固定治具",
"Size": "Φ1.6",
"ToolOther": "FM-2322",
"WorkName": "θ軸組立⑫",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"締付ﾄﾙｸ 80cN･m",
"COLLAR の挿入方向に注意(下図参照)",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2322",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ・Z軸連結",
"WorkItems": [
"◆1. ②の連結部にｸﾞﾘｰｽ塗布",
"2. 1の完成品と①をBOLT WASHER で締結"
],
"WorkPoints": [
"指示箇所に塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "θ・Z軸連結",
"WorkItems": [
"◆1. ②の連結部にｸﾞﾘｰｽ塗布",
"2. 1の完成品と①をBOLT WASHER で締結"
],
"WorkPoints": [
"指示箇所に塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkT... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "θ軸原点確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5747",
"WorkName": "θ軸ﾓｰﾀｰ原点調整治具接続",
"WorkItems": [
"1. ﾓｰﾀに治具を接続する"
],
"WorkPoints": [
"PCｹｰﾌﾞﾙのUSBはPCに接続する",
"【注意】 電源ｽｲｯﾁOFF状態を確認してから接続作業実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5747",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "θ軸原点確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5747",
"WorkName": "θ軸ﾓｰﾀｰ原点調整原点出し操作方法",
"WorkItems": [
"1. PCのPANATERMを起動する",
"2. PANATERM画面になってから､電源SWを【ON】し､電源を供給する",
"4. 【その他を】ｸﾘｯｸする",
"5. 青枠の【Z相ｻｰﾁ】をｸﾘｯｸすると画面が切替わる",
"6. 【ｻｰﾎﾞｵﾝ】をｸﾘｯｸする",
"7. 【Z相ｻｰﾁを】ｸﾘｯｸする",
... | {
"QualityItem": "操作方法",
"ToolManageNo": "FM-5747",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙ角度調整治具",
"Size": "",
"ToolOther": "FM-5689",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"WorkItems": [
"1. ﾉｽﾞﾙ角度調整を行う"
],
"WorkPoints": [
"①ﾎﾙﾀﾞのｾｯﾄﾋﾞｽを緩めてﾎﾙﾀﾞが回転出来る状態にする(16本全て)",
"②ｾﾝｻｰ部ｷﾞｱの〇穴をｾﾝｻｰ投光部分にくる様にｷﾞｱを回転させる(左右2箇所)",
"※ｶｯﾌﾟﾘﾝｸﾞ左右の隙間が均一になる位置で締結",
"ﾉｽﾞﾙΘ位置調整後､ﾉ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5689",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰｹｰﾌﾞﾙFCﾍｯﾄﾞ用",
"Size": "",
"ToolOther": "FM-5723",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"WorkItems": [
"1. ﾉｽﾞﾙ角度調整を行う"
],
"WorkPoints": [
"①ﾎﾙﾀﾞのｾｯﾄﾋﾞｽを緩めてﾎﾙﾀﾞが回転出来る状態にする(16本全て)",
"②ｾﾝｻｰ部ｷﾞｱの〇穴をｾﾝｻｰ投光部分にくる様にｷﾞｱを回転させる(左右2箇所)",
"※ｶｯﾌﾟﾘﾝｸﾞ左右の隙間が均一になる位置で締結",
"ﾉｽﾞ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5723",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"WorkItems": [
"1. ﾉｽﾞﾙ角度調整を行う"
],
"WorkPoints": [
"①ﾎﾙﾀﾞのｾｯﾄﾋﾞｽを緩めてﾎﾙﾀﾞが回転出来る状態にする(16本全て)",
"②ｾﾝｻｰ部ｷﾞｱの〇穴をｾﾝｻｰ投光部分にくる様にｷﾞｱを回転させる(左右2箇所)",
"※ｶｯﾌﾟﾘﾝｸﾞ左右の隙間が均一になる位置で締結",
"ﾉｽﾞﾙΘ位置調整後､... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "θ軸原点確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5747",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"WorkItems": [
"1. ﾉｽﾞﾙ角度調整を行う"
],
"WorkPoints": [
"①ﾎﾙﾀﾞのｾｯﾄﾋﾞｽを緩めてﾎﾙﾀﾞが回転出来る状態にする(16本全て)",
"②ｾﾝｻｰ部ｷﾞｱの〇穴をｾﾝｻｰ投光部分にくる様にｷﾞｱを回転させる(左右2箇所)",
"※ｶｯﾌﾟﾘﾝｸﾞ左右の隙間が均一になる位置で締結",
"ﾉｽﾞﾙΘ位置調整後､ﾉ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5747",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "0.89㎜",
"ToolOther": "14cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"WorkItems": [
"1. ﾉｽﾞﾙ角度調整を行う"
],
"WorkPoints": [
"①ﾎﾙﾀﾞのｾｯﾄﾋﾞｽを緩めてﾎﾙﾀﾞが回転出来る状態にする(16本全て)",
"②ｾﾝｻｰ部ｷﾞｱの〇穴をｾﾝｻｰ投光部分にくる様にｷﾞｱを回転させる(左右2箇所)",
"※ｶｯﾌﾟﾘﾝｸﾞ左右の隙間が均一になる位置で締結",
"ﾉｽﾞﾙΘ位置調... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "14cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "80cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"WorkItems": [
"1. ﾉｽﾞﾙ角度調整を行う"
],
"WorkPoints": [
"①ﾎﾙﾀﾞのｾｯﾄﾋﾞｽを緩めてﾎﾙﾀﾞが回転出来る状態にする(16本全て)",
"②ｾﾝｻｰ部ｷﾞｱの〇穴をｾﾝｻｰ投光部分にくる様にｷﾞｱを回転させる(左右2箇所)",
"※ｶｯﾌﾟﾘﾝｸﾞ左右の隙間が均一になる位置で締結",
"ﾉｽﾞﾙΘ位置調整後､... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"WorkItems": [
"1. ﾉｽﾞﾙ角度調整を行う"
],
"WorkPoints": [
"①ﾎﾙﾀﾞのｾｯﾄﾋﾞｽを緩めてﾎﾙﾀﾞが回転出来る状態にする(16本全て)",
"②ｾﾝｻｰ部ｷﾞｱの〇穴をｾﾝｻｰ投光部分にくる様にｷﾞｱを回転させる(左右2箇所)",
"※ｶｯﾌﾟﾘﾝｸﾞ左右の隙間が均一になる位置で締結",
"ﾉｽﾞﾙΘ位置調整後､ﾉｽﾞﾙﾎﾙﾀﾞの摺動を確認する"... | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "引っ掛かりなくｽﾑｰｽﾞに摺動する事",
"Method": "目視/手感",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.0㎜BOX",
"ToolOther": "40cN･m",
"WorkName": "JOINT取付",
"WorkItems": [
"1. ①にJOINT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾉｽﾞﾙｶﾞｰﾄﾞ、ﾀｲﾏｳﾝﾄ取付",
"WorkItems": [
"1. ①にCLIP をBOLT で取付",
"2. PLATE をSPACER BOLT WASHER で取付"
],
"WorkPoints": [
"CLIP の取付方向に注意(下図参照)",
"CLIP PLATE 取付位置(下図参照･左右共通)",
"PLATE は下方向に押付けながら取付",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"◆1. BRACKET の指定箇所にｸﾞﾘｰｽ塗布",
"2. 1の完成品を①にBOLT で取付"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布",
"ｸﾘｱﾗﾝｽ0.1mmになる様にｼｯｸﾈｽを挟めて締結",
"締結後､隣接のﾌﾞﾗｹｯﾄ同士が傾きなく干渉してい無い事",
"締結後､Z軸を手動にて上下させ問題無く摺動する事",
"締結... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "30cN･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"◆1. BRACKET の指定箇所にｸﾞﾘｰｽ塗布",
"2. 1の完成品を①にBOLT で取付"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布",
"締結後､Z軸を手動にて上下させ問題無く摺動する事",
"締結後､0.1mmのｸﾘｱﾗﾝｽが保てている事を確認する"
],
"Tolks": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"◆1. BRACKET の指定箇所にｸﾞﾘｰｽ塗布",
"2. 1の完成品を①にBOLT で取付"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布",
"締結後､Z軸を手動にて上下させ問題無く摺動する事",
"締結後､0.1mmのｸﾘｱﾗﾝｽが保てている事を確認する"
],
"Tolks": [],
"Inspec... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "補強ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"▲1. PLATE にTRIM TRIM を接着",
"2. 1の完成品とPLATE をSPACER SCREW BOLT WASHER BOLT WASHER で取付"
],
"WorkPoints": [
"SCREW はﾓｰﾀｰ側に底付きさせる(目安7mm)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"Inspection... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "補強ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1の完成品とPLATE をSPACER SCREW BOLT WASHER BOLT WASHER で取付"
],
"WorkPoints": [
"SCREW はﾓｰﾀｰ側に底付きさせる(目安7mm)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ配線",
"WorkItems": [
"1. ﾄﾞﾛｱｺﾈｸﾀの配線をJOINTに固定"
],
"WorkPoints": [
"固定場所に注意(右図参照)",
"継手の穴にｲﾝｼｭﾛｯｸを通して結束する",
"下記寸法にて結束する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾐﾀﾓｰﾀ部配線",
"WorkItems": [
"1. FANｹｰﾌﾞﾙをﾌﾞﾗｹｯﾄに固定",
"2. FANｺﾈｸﾀﾗﾍﾞﾙを修正"
],
"WorkPoints": [
"矢視",
"結束方法は前側･後側共に同じ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ取付(前側NP1~8)",
"WorkItems": [
"1. ①に⑥BRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"⑥BRACKET は共締め",
"上図は説明の為､配線･配管は省略しています",
"⑥BRACKET 締結時､傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ取付(後側NP9~16)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"締付ﾄﾙｸ 95cN･m",
"ﾌｫﾄｾﾝｻ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ取付(後側NP9~16)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"締付ﾄﾙｸ 95cN･m",
"ﾌｫﾄｾﾝｻ配線CN2K303",
"ﾊ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線①(前側NP1~8)",
"WorkItems": [
"1. ①の指示箇所をｲﾝｼｭﾛｯｸにて結束"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸ頭の向きに注意(下図参照)",
"各ｺﾈｸﾀ･配線に無理なｽﾄﾚｽがかからない様にする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線①(後側NP9~16)",
"WorkItems": [
"1. ①の指示箇所をｲﾝｼｭﾛｯｸにて結束"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸ頭の向きに注意(下図参照)",
"各ｺﾈｸﾀ･配線に無理なｽﾄﾚｽがかからない様にする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘｺﾝﾁｭｰﾌﾞ取付",
"WorkItems": [
"1. ①にTUBE(70MM CUT) を取付"
],
"WorkPoints": [
"ﾁｭｰﾌﾞ取付後ﾉｽﾞﾙ上昇確認を行う",
"TUBE(70MM CUT) に折れ､よじれ等無き事",
"TUBE(70MM CUT) は各JOINTに確実に挿入する事"
],
"Tolks": [],
"InspectionNo": "GWEHD-F013-001"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線②(前側NP1~8)",
"WorkItems": [
"1. ①の前側IO基板にｺﾈｸﾀを接続"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "GWEHD-F013-002",
"InspectionItems": [
"検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認"
],
"WorkTypes": [
"▲特殊作業",
"●... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管接続(白配管)",
"WorkItems": [
"1. ①に②を接続"
],
"WorkPoints": [
"②は確実にJOINT根本まで挿入する事",
"②の番号が記載されていない側をJOINTに接続する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリー... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.