input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける",
"2. ①にPLATE PLATE をBOLT で仮取付け",
"3. PLATE PLATE の取付高さ調整及び平面度を測定する"
],
"WorkPoints": [
"表裏面と上面にかける",
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4828",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [],
"WorkPoints": [
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35~1.65)に調整",
"48.5±0.1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4828",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "75.5㎜",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [],
"WorkPoints": [
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35~1.65)に調整",
"48.5±0.1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "75.5㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "平面度0.02㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
"規... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
"規格:0.02... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ:治具を... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ:治具を... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ:... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ:治具... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄ搭載面調整治具",
"Size": "",
"ToolOther": "FM-4639",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4639",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(右実装部)",
"WorkItems": [
"1. ④にGUIDE ②をBOLT で､③をBOLT WASHER で取付け"
],
"WorkPoints": [
"②､③をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
"②､③は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(右実装部)",
"WorkItems": [
"1. ④にGUIDE ②をBOLT で､③をBOLT WASHER で取付け"
],
"WorkPoints": [
"②､③をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
"②､③は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(右実装部)",
"WorkItems": [
"1. ④にGUIDE ②をBOLT で､③をBOLT WASHER で取付け"
],
"WorkPoints": [
"②､③をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
"②､③は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(右実装部)",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際は標準ﾌﾟﾚｰﾄを取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整... | {
"QualityItem": "遮光確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "LEDが消灯する事",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(右実装部)",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際は標準ﾌﾟﾚｰﾄを取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(右実装部)",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際は標準ﾌﾟﾚｰﾄを取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(右実装部)",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"3. 通常ｽﾋﾟｰﾄﾞで上記B,Cﾂﾏﾐで調整｡",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"1. ｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際は標準ﾌﾟﾚｰﾄを取付けて実施する",
"ｴｰ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "組立治具取付け(左実装部)",
"WorkItems": [
"1. ①を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"右実装部と左実装部では組立治具取付け位置が前後逆になる",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締め付け",
"ﾘﾆｱﾌﾞｯｼｭの狭いほうをPINに押し当てて取付け",
"ｼｯｸﾈｽﾃｰﾌﾟ(0.05㎜)で隙... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ組立台",
"Size": "",
"ToolOther": "FM-4850",
"WorkName": "組立治具取付け(左実装部)",
"WorkItems": [
"1. ①を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"右実装部と左実装部では組立治具取付け位置が前後逆になる",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締め付け",
"ﾘﾆｱﾌﾞｯｼｭの狭いほうをPINに押し当てて取付け",
"ｼｯｸﾈｽﾃｰﾌﾟ(0.05㎜)... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4850",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "組立治具取付け(左実装部)",
"WorkItems": [
"1. ①を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"右実装部と左実装部では組立治具取付け位置が前後逆になる",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締め付け",
"ﾘﾆｱﾌﾞｯｼｭの狭いほうをPINに押し当てて取付け",
"ｼｯｸﾈｽﾃｰﾌﾟ(0.05㎜)で... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾊﾞﾙﾌﾞ・ｽﾋﾟｺﾝ取付け(左実装部)",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付け",
"2. ①に③をWASHER WASHER で取付け",
"1. ①に②をBOLT WASHER で取付け",
"2. ①に③をWASHER WASHER で取付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｼﾞｮｲﾝﾄ取付け(左実装部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻ取付け(左実装部)",
"WorkItems": [
"1. ①に②WASHER をBOLT WASHER で取付け"
],
"WorkPoints": [
"位置決めについてはﾄﾞｸﾞ取付け時の為､仮固定",
"締付:SD-011666-052にて締付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "配管引き回①(左実装部)",
"WorkItems": [
"1. TUBE を各寸法にｶｯﾄする",
"2. ①にTUBE を引き回す",
"3. ①にTUBE を引き回す"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰB",
"ｼﾘﾝﾀﾞｰA",
"Aの配管をｼﾘﾝﾀﾞｰB(下)とTｼﾞｮｲﾝﾄ(右下)へ繋ぐ",
"Bの配管をﾊﾞﾙﾌﾞ(左)とTｼﾞｮｲﾝﾄ(左下)へ繋ぐ",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回②(左実装部)",
"WorkItems": [
"1. ①にTUBE を引き回す",
"2. ①にTUBE を引き回す",
"3. ①にTUBE を引き回す",
"4. ①にTUBE を引き回す"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰB",
"ｼﾘﾝﾀﾞｰA",
"Dの配管をｼﾘﾝﾀﾞｰB(上)とTｼﾞｮｲﾝﾄ(右中)へ繋ぐ",
"Eの配管をｽﾋﾟｺﾝ(右下)とTｼ... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回③(左実装部)",
"WorkItems": [
"1. ①にTUBE を引き回す",
"2. ①にTUBE を引き回す"
],
"WorkPoints": [
"Iの配管をTｼﾞｮｲﾝﾄ(右上)とﾊﾞﾙﾌﾞ(右)へ繋ぐ",
"Jの配管をTｼﾞｮｲﾝﾄ(中上)とｽﾋﾟｺﾝ(左下)へ繋ぐ",
"Kの配管をｽﾋﾟｺﾝ(左上)とTｼﾞｮｲﾝﾄ(左上)へ繋ぐ"
],
"Tolks": [],
"Insp... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回④(左実装部)",
"WorkItems": [
"1. ①の各配管を㉖で縛る"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞのｽﾋﾟｺﾝとｼﾞｮｲﾝﾄが図の向きになるように引き回すこと事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回⑤(第2実装部)",
"WorkItems": [
"1.①の シリンダー部のエアー配管を㉖で縛る",
"2. スピコンのジョイント部分を㉗で縛る（傾き防止の為）"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸの向きに注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wo... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ組立台",
"Size": "",
"ToolOther": "FM-4850",
"WorkName": "上ﾌﾟﾚｰﾄの取付(左実装部)",
"WorkItems": [
"1. ①に②を乗せる"
],
"WorkPoints": [
"乗せる前に4本のｼｬﾌﾄが動く程度に仮止めされているか確認する",
"こじれるとﾎﾞｰﾙｽﾌﾟﾗｲﾝを破損するので注意",
"上ﾌﾟﾚｰﾄと各ｼﾞｮｲﾝﾄが干渉してい無い事"
],
"Tolks": [],
"InspectionNo": "",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4850",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄの取付(左実装部)",
"WorkItems": [
"1. ①に②を乗せる"
],
"WorkPoints": [
"乗せる前に4本のｼｬﾌﾄが動く程度に仮止めされているか確認する",
"こじれるとﾎﾞｰﾙｽﾌﾟﾗｲﾝを破損するので注意",
"上ﾌﾟﾚｰﾄと各ｼﾞｮｲﾝﾄが干渉してい無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示場所が干渉してい無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ組立台",
"Size": "",
"ToolOther": "FM-4850",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. ①に②を⑯で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(0.05㎜以下)"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4850",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. ①に②を⑯で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(0.05㎜以下)",... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. ①に②を⑯で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(0.05㎜以下)",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｬﾌﾄHｶｯﾄ方向合わせ治具",
"Size": "",
"ToolOther": "FM-4956",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. ①に②を⑯で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(0.0... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4956",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4828",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. ①に②を⑯で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け",
"1. ①に②を⑯で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4828",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾁｪｯｶｰ前準備(左実装部)",
"WorkItems": [
"1. ㉖の各コネクターを①に取付ける"
],
"WorkPoints": [
"AUTO動作",
"MANUAL動作",
"ｴｱｰ配管は後ほど挿入する為､繋が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [
"1. CYL-NUT に油砥石をかける",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する"
],
"WorkPoints": [
"芯出し調整時にはｴｱｰを入れ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [
"1. CYL-NUT に油砥石をかける",
"5. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞ寸法の位置決め後､ﾛｯｸする",
"3. ①のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する",
"◆4. WASHER CYL-NUT をｼﾘﾝﾀﾞｰに取付け"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞ位置調整治具",
"Size": "",
"ToolOther": "FM-2982",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [
"1. CYL-NUT に油砥石をかける",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する"
],
"WorkPoints": [
"芯出し調整時にはｴｱｰを入れ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2982",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [],
"WorkPoints": [
"㉚㉝でロックする"
],
"Tolks": [
"締付ﾄﾙｸ 30.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WASHE... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "7.50±0.05㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [
"1. CYL-NUT に油砥石をかける",
"5. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞ寸法の位置決め後､ﾛｯｸする",
"3. ①のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する",
"◆4. WASHER CYL-NUT をｼﾘﾝﾀﾞｰに取付け"
],
"WorkPoin... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:8",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "36㎜",
"ToolOther": "30.0N･m",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [],
"WorkPoints": [
"㉚㉝でロックする"
],
"Tolks": [
"締付ﾄﾙｸ 30.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞｸﾞ取付け調整(左実装部)",
"WorkItems": [
"1. DOG に防錆油を塗布する",
"2. ①にDOG をBOLT WASHER で取付け",
"3. ｾﾝｻ位置調整後､Aを締付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させﾄﾞｸﾞとｾﾝｻｰが接触しないように調整する"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾄﾞｸﾞ取付け調整(左実装部)",
"WorkItems": [
"1. DOG に防錆油を塗布する",
"2. ①にDOG をBOLT WASHER で取付け",
"3. ｾﾝｻ位置調整後､Aを締付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させﾄﾞｸﾞとｾﾝｻｰが接触しないように調整する",
"ｾﾝｻｰの左右はｾﾝﾀﾞｰ奥行きは2/3を目安に取付け"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [],
"WorkPoints": [
"48.5±0.1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "WEAV-G002-C08",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"48.5±0.1㎜",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "出代:48.5㎜±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [],
"WorkPoints": [
"48.5±0.1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"48.5±0.1㎜",
"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:110.5㎜±0.05㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [],
"WorkPoints": [
"48.5±0.1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"48.5±0.1㎜",
"75.5... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける",
"2. ①にPLATE PLATE をBOLT で仮取付け",
"3. PLATE PLATE の取付高さ調整及び平面度を測定する"
],
"WorkPoints": [
"表裏面と上面にかける",
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4828",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [],
"WorkPoints": [
"48.5±0.1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"48.5±0.1㎜",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4828",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "75.5㎜",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [],
"WorkPoints": [
"48.5±0.1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"48.5±0.1㎜",
"75.... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "75.5㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "平面度0.02㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
"規... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. ①を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
"①,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
"規格:0.02... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:①を基準に平面度0.05mm以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:①を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:①を基準に平面度0.05mm以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:①を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:①を基準に平面度0.05mm以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:①を基準に-0.04~-0.09mm",
"⑨､⑩､... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:①を基準に平面度0.05mm以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:①を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄ搭載面調整治具",
"Size": "",
"ToolOther": "FM-4639",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. ①の上ﾌﾟﾚｰﾄに②を取付け",
"2. ②の平面度調整を行う"
],
"WorkPoints": [
"①､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:①を基準に平面度0.05mm以内",
"②､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:①を基準に-0.04~-0.09mm",
"⑨､⑩､... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4639",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(左実装部)",
"WorkItems": [
"1. ④にGUIDE ②をBOLT で､③をBOLT WASHER で取付け"
],
"WorkPoints": [
"②､③をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
"②､③は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(左実装部)",
"WorkItems": [
"1. ④にGUIDE ②をBOLT で､③をBOLT WASHER で取付け"
],
"WorkPoints": [
"②､③をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
"②､③は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(左実装部)",
"WorkItems": [
"1. ④にGUIDE ②をBOLT で､③をBOLT WASHER で取付け"
],
"WorkPoints": [
"②､③をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
"②､③は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(左実装部)",
"WorkItems": [
"2. ｽﾋﾟｺﾝの調整､下図の回転数でB,D固定｡",
"1. ①のｾﾝｻｰ部の遮光を確認する",
"2. ｽﾋﾟｺﾝの調整､下図の回転数でB,D固定｡",
"1. ①のｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際は標準ﾌﾟﾚｰﾄを取付けて実施する",
... | {
"QualityItem": "遮光確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "LEDが消灯する事",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(左実装部)",
"WorkItems": [
"2. ｽﾋﾟｺﾝの調整､下図の回転数でB,D固定｡",
"1. ①のｾﾝｻｰ部の遮光を確認する",
"2. ｽﾋﾟｺﾝの調整､下図の回転数でB,D固定｡",
"1. ①のｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際は標準ﾌﾟﾚｰﾄを取付けて実施する",
... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(左実装部)",
"WorkItems": [
"2. ｽﾋﾟｺﾝの調整､下図の回転数でB,D固定｡",
"1. ①のｾﾝｻｰ部の遮光を確認する",
"2. ｽﾋﾟｺﾝの調整､下図の回転数でB,D固定｡",
"1. ①のｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際は標準ﾌﾟﾚｰﾄを取付けて実施する",
... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(左実装部)",
"WorkItems": [
"2. ｽﾋﾟｺﾝの調整､下図の回転数でB,D固定｡",
"3. 通常ｽﾋﾟｰﾄﾞで上記A,B,Cﾂﾏﾐで調整｡",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"1. ①のｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際は標準ﾌﾟﾚｰﾄを取付けて実施する",... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞを実施する｡",
"1. ①、②に㉖のコネクタ、エアー配管を接続する"
],
"WorkPoints": [
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:500~505kPa",
"ｴｰｼﾞﾝｸﾞ回数:2000回"
],
"Tolks": [],
"InspectionNo": "",
"Ins... | {
"QualityItem": "動作回数確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2000回",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞを実施する｡",
"1. ①、②に㉖のコネクタ、エアー配管を接続する"
],
"WorkPoints": [
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:500~505kPa",
"ｴｰｼﾞﾝｸﾞ回数:2000回"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "最終確認",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"3. ｴｰｼﾞﾝｸﾞ完了後､再度ｽﾋﾟｰﾄﾞ調整を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
"①、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める②、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確認し 再度締... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "最終確認",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"3. ｴｰｼﾞﾝｸﾞ完了後､再度ｽﾋﾟｰﾄﾞ調整を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
"①、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める②、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確認し 再度締... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "最終確認",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
"①、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める②、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確認し 再度締め付ける。（こじれがある場合再度①、②を繰り返す）③、こじれが取れない場合は㉖の電... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "最終確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:基板下受け上下ｽﾋﾟｰﾄﾞ調整",
"規格値【通常ｽﾋﾟｰﾄﾞ】 上昇:1.30~1.40S 下降:1.30~1.40S... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付冶具",
"Size": "",
"ToolOther": "FM-4919",
"WorkName": "銘板貼付(右実装部)",
"WorkItems": [
"1. ①の貼付面に㉖で拭取りLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"右実装部",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-4919",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付(右実装部)",
"WorkItems": [
"1. ①の貼付面に㉖で拭取りLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"右実装部",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付冶具",
"Size": "",
"ToolOther": "FM-4919",
"WorkName": "銘板貼付(左実装部)",
"WorkItems": [
"1. ①の貼付け面に㉖で拭取りLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"左実装部",... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-4919",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付(左実装部)",
"WorkItems": [
"1. ①の貼付け面に㉖で拭取りLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"左実装部",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ移載治具",
"Size": "",
"ToolOther": "FM-4852",
"WorkName": "払い出し準備",
"WorkItems": [
"1. ①、②に㉗を治具専用ボルトで取付ける"
],
"WorkPoints": [
"下ﾌﾟﾚｰﾄにﾎﾞﾙﾄ4箇所で取付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4852",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"1. LEVER に砥石をかけ防錆油を全体に塗布する",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"1. LEVER に砥石をかけ防錆油を全体に塗布する",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2個",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"1. LEVER に砥石をかけ防錆油を全体に塗布する",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1個",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車取付部ﾒﾀﾙ圧入治具",
"Size": "",
"ToolOther": "FM-2144",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"1. LEVER に砥石をかけ防錆油を全体に塗布する",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2144",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部ﾚﾊﾞｰ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6510",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"1. LEVER に砥石をかけ防錆油を全体に塗布する",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6510",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"1. LEVER に砥石をかける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"1. LEVER に砥石をかける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2個",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車取付部ﾒﾀﾙ圧入治具",
"Size": "",
"ToolOther": "FM-2144",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"3. 1完成品に2完成品を圧入する"
],
"WorkPoints": [
"塗布位置",
"継ぎ目位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2144",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"4. 3完成品にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立1",
"WorkItems": [],
"WorkPoints": [
"当付け",
"六角穴側"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 12.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Word... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立1",
"WorkItems": [],
"WorkPoints": [
"当付け",
"六角穴側"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 12.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立1",
"WorkItems": [
"2. 1完成品に③を取付ける",
"1. ①②に砥石をかけ①に②を⑯で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの向きに注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "13㎜",
"ToolOther": "12.0N･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立1",
"WorkItems": [
"2. 1完成品に③を取付ける",
"1. ①②に砥石をかけ①に②を⑯で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの向きに注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "12.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立2",
"WorkItems": [
"2. ①にSPRING とPLATE をBOLT にて取付",
"◆1. SPRING とBOLT にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"図の指示部に塗布すこと",
"PLATE の取付向きに注意:小さい穴の方にﾎﾞﾙﾄを通す"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1個",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立2",
"WorkItems": [
"2. ①にSPRING とPLATE をBOLT にて取付",
"◆1. SPRING とBOLT にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"図の指示部に塗布すこと",
"PLATE の取付向きに注意:小さい穴の方にﾎﾞﾙﾄを通す"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:2個",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立2",
"WorkItems": [
"2. ①にSPRING とPLATE をBOLT にて取付",
"◆1. SPRING とBOLT にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"図の指示部に塗布すこと",
"PLATE の取付向きに注意:小さい穴の方にﾎﾞﾙﾄを通す"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立3",
"WorkItems": [
"1. ①にBOLT BOLT WASHER を差込む",
"2. ①にSTOPPER をBOLT WASHER にて取付",
"3. ①にSTOPPER をBOLT WASHER にて取付",
"1. ①にBOLT BOLT WASHER を差込む",
"2. ①にSTOPPER をBOLT WASHER にて取付",
"3. ①にS... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "13㎜",
"ToolOther": "20.5N･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立3",
"WorkItems": [
"4. ①にGRIP をNUT にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立3",
"WorkItems": [
"4. ①にGRIP をNUT にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.