input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了後､ﾅｯﾄ2か所に... | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "74±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "9.8N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "3.2N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了後... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙線部にはめる",
... | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "59±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙線部にはめる... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄﾃﾝｼｮﾝｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6591",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6591",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸合いﾏｰｸ追加",
"WorkItems": [
"1. TP軸を原点復帰する",
"2. 合いﾏｰｸを付ける"
],
"WorkPoints": [
"黄色ﾏｰｶｰ2ヵ所",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸合いﾏｰｸ追加",
"WorkItems": [
"1. TP軸を原点復帰する",
"2. 合いﾏｰｸを付ける"
],
"WorkPoints": [
"黄色ﾏｰｶｰ2ヵ所",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとする"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:TP... | {
"QualityItem": "合いﾏｰｸ記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの合いﾏｰｸが2箇所付いてること",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"Inspectio... | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "74±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5052",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
]... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5052",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す",
"4. 治具を取付ける"
],
"WorkPoints": [
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ",
"A0",
"A 1",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています",
"ﾊﾟﾜｰOFFにて締付の事",
"±0.05㎜以内(中央)±0.2㎜以内(左... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています",
"ﾊﾟﾜｰOFFにて締付の事",
"±0.05㎜以内(中央)±0.2㎜以内(... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems":... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFにて締付の事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:ｶｯﾌﾟﾘﾝｸﾞ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTy... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し",
"2. 下段23Slotから上段23Slotへ移動し高さ確認"
],
"WorkPoints": [
"下段23Slot調整後すぐには原点復帰は決して行わ無い事原点高さが変わる場合があります"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し",
"2. 下段23Slotから上段23Slotへ移動し高さ確認"
],
"WorkPoints": [
"下段23Slot調整後すぐには原点復帰は決して行わ無い事原点高さが変わる場合があります"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し",
"2. 下段23Slotから上段23Slotへ移動し高さ確認"
],
"WorkPoints": [
"下段23Slot調整後すぐには原点復帰は決して行わ無い事原点高さが変わる場合があります"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"補給部は内側を緩め調整",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"±0.05㎜以内(中央部) ±0.2㎜以内(左右)",... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"補給部は内側を緩め調整",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"±0.05㎜以内(中央部) ±0.2㎜以内(左右)"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整治具",
"Size": "",
"ToolOther": "FM-6449",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6449",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.1㎜で投光、原点で遮光する事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"ﾎﾞｰﾙﾈｼﾞとｺﾞﾑｽﾄｯﾊ... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｽﾄｯﾊﾟｰとの干渉無き事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-①(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. TP軸をﾊﾟﾜｰONする",
"2. ﾄﾚｲ本体の原点復帰",
"3. 引き出部を連結位置へ移動",
"4. 引き出部をNG排出部へ高さ位置を合わす",
"5. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かす"
],
"WorkPoints": [
"画面上で①②③④のﾎﾞﾀﾝを順次押... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [
"C~F間に0.3㎜のｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"LMｶﾞｲﾄﾞとの隙間が無い事をｼｯｸﾈｽｹﾞｰｼﾞで確認"... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする"
],
"WorkPoints": [
"0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"LMｶﾞｲﾄﾞとの隙間が無い事をｼｯｸﾈｽｹﾞｰｼﾞで確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする"
],
"WorkPoints": [
"0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"LMｶﾞｲﾄﾞとの隙間が無い事をｼｯｸﾈｽｹﾞｰｼﾞで確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする"
],
"WorkPoints": [
"0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"LMｶﾞｲﾄﾞとの隙間が無い事をｼｯｸﾈｽｹﾞｰｼﾞで確認"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionI... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする"
],
"WorkPoints": [
"0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"LMｶﾞｲﾄﾞとの隙間が無い事をｼｯｸﾈｽｹﾞｰｼﾞで確認"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionI... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.3㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩め... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行だし治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
"T... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "12.5㎜~13.0㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. TP軸原点復帰を行う",
"3. 吸着位置でﾚﾊﾞｰの確認を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"4. ﾊﾟﾜｰをOFF",
"■5. TP軸ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの増し締め"
],
"WorkPoints": [
"ﾊﾟﾚｯﾄをｶﾞｲﾄﾞに当付ける",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"■安全作業"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"■安全作業",
"WETE-G002-A11"
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾄﾚｲ本体のの原点復帰",
"2. 引き出部を連結位置へ移動",
"3. 引き出部をNG排出部へ移動",
"4. ﾊﾟﾚｯﾄ戻しへ移動",
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること",
"... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"LEDが点灯のこと(赤緑)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"LEDが点灯のこと(赤緑)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "40cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"LEDが点灯のこと(赤緑)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾄﾚｲ本体のの原点復帰",
"2. 引き出部を連結位置へ移動",
"3. 引き出部をNG排出部へ移動",
"4. ﾊﾟﾚｯﾄ戻しへ移動",
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること",
"再度動作をさせｾﾝｻの中心にあること",
... | {
"QualityItem": "光軸確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｾﾝｻの中心に投光状態である事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動",
"3. 現在値の確認",
"3. 現在値の確認"
],
"WorkPoints": [
"『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が投光(水色)しているか確認",
"遮光(黒色)の場合はｾﾝｻｰを投光する位置に調整する... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1.ﾊﾟﾚｯﾄ戻し位置でﾁｪｯｶｰの『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が 投光(水色)しているか確認する",
"3. 現在値の確認",
"2. TP軸ﾏﾆｭｱﾙ動作を押す",
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動"
],
"WorkPoints": [
"現在値 -100.0... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動",
"3. 現在値の確認",
"3. 現在値の確認"
],
"WorkPoints": [
"『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が投光(水色)しているか確認",
"遮光(黒色)の場合はｾﾝｻｰを投光する位置に調整する... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.33stで投光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.47st -99.53㎜位置まで移動"
],
"WorkPoints": [
"-99.53で点灯の場合はｾﾝｻをﾏｲﾅｽ側(矢印側)へ動かし消灯させる 消灯位置は安定した状態になるよう少しづつ移動させる事",
"･+0.47st -99.66~-99.53㎜の間で遮光(黒色... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"2. ｾﾝｻの固定を行う",
"3. 一連の調整完了後､再度ｾﾝｻの投光･遮光を確認"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Work... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.47st -99.53㎜位置まで移動"
],
"WorkPoints": [
"-99.53で点灯の場合はｾﾝｻをﾏｲﾅｽ側(矢印側)へ動かし消灯させる 消灯位置は安定した状態になるよう少しづつ移動させる事",
"･+0.47st -99.66~-99.53㎜の間で遮光(黒色... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.47stで遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. TP軸の原点復帰を行う",
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"矢印方向に当てつけ",
"4. ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4. TP軸を動作させｾﾝｻ位置を調整する",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動か... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.2㎜(治具出代)",
"0.1mm",
"ﾏｲﾅｽ側O/Rｾﾝｻが-99.9㎜... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "規定ｽﾄﾛｰｸで投光・遮光している事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"3. 治具をDOGにｾｯﾄする",
"2. 引き出部ｱｰﾑを吸着位置に動かす",
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"矢印方向に当てつけ",
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"3. 治具をDOGにｾｯﾄする",
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [],
"I... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkT... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"3. 治具をDOGにｾｯﾄする",
"2. 引き出部ｱｰﾑを吸着位置に動かす",
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)",
... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "規定ｽﾄﾛｰｸで投光・遮光している事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. ﾄﾚｲ本体の原点復帰",
"2. 引き出部を連結位置へ移動",
"3.ｽﾄｯﾊﾟ位置の調整",
"4.TTL軸と引き出し連結部の隙間確認を行う"
],
"WorkPoints": [
"ｽﾄｯﾊﾟをTTL軸ﾌﾟﾚｰﾄに当てつけ",
"黄丸部分に0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [],
"WorkPoints": [
"ｽﾄｯﾊﾟをTTL軸ﾌﾟﾚｰﾄに当てつけ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [],
"WorkPoints": [
"TTL軸ﾌﾟﾚｰﾄと連結部ｼｬﾌﾄ間",
"TTL軸ﾌﾟﾚｰﾄとｽﾄｯﾊﾟ間"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝをｾｯﾄする",
"2. 治具をｾｯﾄする"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付ける",
"投光用",
"遮光用",
"上下段に挿入",
"確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"In... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"2. 治具をｾｯﾄする"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付ける",
"投光用",
"遮光用",
"確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "−99.9㎜で投光−100.0㎜で遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:補給部②:NGﾊﾟﾚｯﾄ③:ﾏｶ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:補給部... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが-99.9㎜で投光、-100.0㎜で遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoin... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoints":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoints": [],
... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "支持部にｸﾞﾘｰｽが塗布されている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝ(ﾄﾚｲﾊﾟﾚｯﾄ入り)をｾｯﾄする",
"2. TL軸･TP軸のｽﾋﾟｰﾄﾞを高速に切替",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"NG排出部及びﾏｶﾞｼﾞﾝの奇数段にﾄﾚｲﾊﾟﾚｯﾄがｾｯﾄされていること... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝ(ﾄﾚｲﾊﾟﾚｯﾄ入り)をｾｯﾄする",
"2. TL軸･TP軸のｽﾋﾟｰﾄﾞを高速に切替",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"NG排出部及びﾏｶﾞｼﾞﾝの奇数段にﾄﾚｲﾊﾟﾚｯﾄがｾｯﾄされていること",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙ... | {
"QualityItem": "点灯確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが不安定な動作をし無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "45cN･m",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙ... | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "16㎜赤消灯、緑点灯",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙ... | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "17㎜赤点灯、緑点灯",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認①",
"WorkItems": [
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.