input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬﾌﾄ部組立",
"WorkItems": [
"2. ①に②を⑯で仮取付ける",
"3. ①裏面のみ防錆油を塗布する",
"1. ①に油砥石を全面(側面も含む)かける"
],
"WorkPoints": [
"･表裏全体に砥石をかけ､ﾊﾞﾘ･ｶｴﾘ等無い事を確認する",
"※ ｼｬﾌﾄ締め付け無い事､ｼｬﾌﾄ動く程度仮止め",
"SD-10164025-028にて本締結"
],
"Tolks": ... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P002ﾌﾟﾚｰﾄ仮組立・銘板貼付け",
"WorkItems": [
"1. ①の表面に②を取付ける",
"2. ①に⑥⑦を貼付け"
],
"WorkPoints": [
"約19㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1右:(R422... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "圧入台",
"Size": "",
"ToolOther": "",
"WorkName": "下受けﾌﾞﾛｯｸ固定部組立",
"WorkItems": [
"1. BLOCK にPIN を圧入する"
],
"WorkPoints": [
"BLOCK の下面に砥石をかけておく事",
"突き当たりまで圧入する",
"D-Pin_挿入方向指示"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ組立台",
"Size": "",
"ToolOther": "FM-2777",
"WorkName": "P001油砥石がけ・ｹｰﾌﾞﾙｻﾎﾟｰﾄ取付",
"WorkItems": [],
"WorkPoints": [
"基板ﾎﾙﾀﾞｰ組立台:FM-2777"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾀｲﾏｳﾝﾄ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2777",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "P001油砥石がけ・ｹｰﾌﾞﾙｻﾎﾟｰﾄ取付",
"WorkItems": [],
"WorkPoints": [
"基板ﾎﾙﾀﾞｰ組立台:FM-2777"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾀｲﾏｳﾝﾄ向き"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "本体取付①",
"WorkItems": [
"1. ⑥に①を⑯⑰で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "70cN･m",
"WorkName": "本体取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "本体取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N.m",
"WorkName": "本体取付③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N.m±10%9.8N.m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "本体取付④",
"WorkItems": [
"2. ⑥にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｼﾞｮｲﾝﾄﾌﾞﾗｹｯﾄ、ｾﾝｻｰ取付",
"WorkItems": [
"1. ⑥に⑦をBOLT WASHER で取付ける",
"1. ⑥にWASHER ⑧をBOLT WASHER で仮付け"
],
"WorkPoints": [
"SD-0164025-030で本締結"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "配管①",
"WorkItems": [
"1. ①にJOINT とTUBE を取付ける"
],
"WorkPoints": [
"下記寸法に配管を切る事",
"※ 先端ﾌﾗｯﾄﾀｲﾌﾟのﾗｼﾞﾍﾟﾝで 確実に最後まで押入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "長さ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの長さでｶｯﾄしてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管①",
"WorkItems": [
"1. ①にJOINT とTUBE を取付ける"
],
"WorkPoints": [
"下記寸法に配管を切る事",
"※ 先端ﾌﾗｯﾄﾀｲﾌﾟのﾗｼﾞﾍﾟﾝで 確実に最後まで押入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "配管②",
"WorkItems": [
"1. ①にTUBE を取付ける"
],
"WorkPoints": [
"下記寸法に配管を切る事",
"※ 先端ﾌﾗｯﾄﾀｲﾌﾟのﾗｼﾞﾍﾟﾝで 確実に最後まで押入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "長さ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの長さでｶｯﾄしてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管②",
"WorkItems": [
"1. ①にTUBE を取付ける"
],
"WorkPoints": [
"下記寸法に配管を切る事",
"※ 先端ﾌﾗｯﾄﾀｲﾌﾟのﾗｼﾞﾍﾟﾝで 確実に最後まで押入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線",
"WorkItems": [
"1. 各ｺﾈｸﾀに配線を接続する"
],
"WorkPoints": [
"･干渉し無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B****R/P",
"B****R/P",
"1B****",
"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線",
"WorkItems": [
"1. 各ｺﾈｸﾀに配線を接続する"
],
"WorkPoints": [
"･干渉し無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B****R/P",
"B****R/P",
"1B****",
"... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "干渉無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "結束・整線",
"WorkItems": [
"1. 配管をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ﾘﾆｱﾌﾞｯｼｭ側に線を入れる｡赤線より外側に出無い事(自動ﾋﾟﾝﾌﾞﾛｯｸに干渉恐れ)",
"ﾍﾞｰｽﾌﾟﾚｰﾄ全面に防錆油塗布",
"ｾﾝｻの可動範囲を確認し結束"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P002ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ⑥に⑦を載せる"
],
"WorkPoints": [
"こじれるとﾎﾞｰﾙｽﾌﾟﾗｲﾝを破損するので注意",
"SD-0164025-028で本締結"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･載... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに取付してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "昇降ﾌﾟﾚｰﾄ位置決め治具ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "FM-3165-",
"WorkName": "P002ﾌﾟﾚｰﾄ位置調整",
"WorkItems": [
"1. ⑥のｼｬﾌﾄの向きを調整しﾎﾞﾙﾄを締結し､①を⑯で取付ける",
"2. 組立台(FM-2777）に㉗を取付ける",
"3. 隙間確認･調整する"
],
"WorkPoints": [
"治具とﾍﾞｰｽﾌﾟﾚｰﾄにｽｷﾏ無き事",
"ｽｷﾏ無き事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3165-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "P002ﾌﾟﾚｰﾄ位置調整",
"WorkItems": [],
"WorkPoints": [
"ｽｷﾏ無き事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｽｷﾏ無き事",
"①とHｶｯﾄの取付方向"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-010",
"I... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "P002ﾌﾟﾚｰﾄ位置調整",
"WorkItems": [],
"WorkPoints": [
"ｽｷﾏ無き事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｽｷﾏ無き事",
"①とHｶｯﾄの取付方向",
"ｽｷﾏ無き事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｼｯｸﾈｽｹﾞｰｼ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰｼﾘﾝﾀﾞｰ位置調整治具",
"Size": "",
"ToolOther": "FM-2999FM-2982",
"WorkName": "ｼﾘﾝﾀﾞｰﾅｯﾄ固定",
"WorkItems": [
"2. ㉘でプレートとシリンダーの芯出しを行いシリンダーを固定する",
"◆3. CYL-NUT WASHER をｼﾘﾝﾀﾞｰに取付",
"4. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞの位置決め後ﾛｯｸする｡",
"1. ⑥に㉗の配管（Ф6）をつなぐ"
],
"WorkPoints": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999FM-2982",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N.m",
"WorkName": "ｼﾘﾝﾀﾞｰﾅｯﾄ固定",
"WorkItems": [],
"WorkPoints": [
"0.5MPaに設定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｼﾘﾝﾀﾞｰ",
"ﾌﾟﾚｰﾄ",
"◆作... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰﾅｯﾄ固定",
"WorkItems": [
"2. ㉘でプレートとシリンダーの芯出しを行いシリンダーを固定する",
"◆3. CYL-NUT WASHER をｼﾘﾝﾀﾞｰに取付",
"4. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞの位置決め後ﾛｯｸする｡",
"1. ⑥に㉗の配管（Ф6）をつなぐ"
],
"WorkPoints": [
"0.5MPaに設定する",
"･最上死点及び最下... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/8粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰﾅｯﾄ固定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"※CYL-NUTの穴の深さは8.5±0.05㎜",
"8.5±0.05㎜",
"㉚でロッ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "8.5±0.05㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｾﾝｻｰﾄﾞｸﾞ取付",
"WorkItems": [
"1. ⑥にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させ､DOG とｾﾝｻｰが接触しないよう調整する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"W... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｾﾝｻｰﾄﾞｸﾞ取付",
"WorkItems": [
"1. ⑥にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させ､DOG とｾﾝｻｰが接触しないよう調整する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰﾄﾞｸﾞ取付",
"WorkItems": [
"1. ⑥にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させ､DOG とｾﾝｻｰが接触しないよう調整する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"PHｾ... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "干渉無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "K024取付・調整①",
"WorkItems": [
"1. ⑦に⑥をBOLT で取付ける",
"2. ⑥の位置決めをして固定する"
],
"WorkPoints": [
"A寸法:89.5±0.1㎜(ﾉｷﾞｽにて測定)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "K024取付・調整①",
"WorkItems": [],
"WorkPoints": [
"A寸法:89.5±0.1㎜(ﾉｷﾞｽにて測定)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･治具FM-4139をｾｯﾄ ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾋﾟﾝﾌﾞﾛｯｸ位置決め治具",
"Size": "",
"ToolOther": "FM-4139",
"WorkName": "K024取付・調整①",
"WorkItems": [
"1. ⑦に⑥をBOLT で取付ける",
"2. ⑥の位置決めをして固定する"
],
"WorkPoints": [
"A寸法:89.5±0.1㎜(ﾉｷﾞｽにて測定)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "WDQB-F013-010",
"In... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4139",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "89.5±0.1㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "K024取付・調整①",
"WorkItems": [],
"WorkPoints": [
"A寸法:89.5±0.1㎜(ﾉｷﾞｽにて測定)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･治具FM-4139をｾｯﾄ ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "89.5±0.1㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "P018取付け",
"WorkItems": [
"1. ⑥にGUIDE をBOLT で取付ける｡"
],
"WorkPoints": [
"手前側に寄せて固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "P018取付け",
"WorkItems": [
"1. ⑥にGUIDE をBOLT で取付ける｡"
],
"WorkPoints": [
"手前側に寄せて固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾕﾆｯﾄﾁｪｯｶｰ操作説明",
"WorkItems": [],
"WorkPoints": [
"5.00~5.05MPa",
"AUTO動作",
"MANUAL動作",
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける｡",
"2. ⑥にPLATE PLATE をBOLT で取付ける｡",
"3. PLATE PLATE の取付け高さ調整および平面度を測定する｡"
],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5㎜を治具台にﾍﾞｰｽﾌﾟﾚｰﾄ当付で取付",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｸﾗﾝﾌﾟﾌﾞﾚｰﾄﾞ押上板位置出し治具昇降ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-3178FM-3165-",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける｡",
"2. ⑥にPLATE PLATE をBOLT で取付ける｡",
"3. PLATE PLATE の取付け高さ調整および平面度を測定する｡"
],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3178FM-3165-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N.m",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5㎜を治具台にﾍﾞｰｽﾌﾟﾚｰﾄ当付で取付",
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35~1.65)に調整"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N.m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5㎜を治具台にﾍﾞｰｽﾌﾟﾚｰﾄ当付で取付",
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35~1.65)に調整"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "WDQB-F013-010",... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "49±0.1㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける｡",
"2. ⑥にPLATE PLATE をBOLT で取付ける｡",
"3. PLATE PLATE の取付け高さ調整および平面度を測定する｡"
],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5㎜を治具台にﾍﾞｰｽﾌﾟﾚｰﾄ当付で取付",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年校正対象外",
"ToolRecord": "校正成績書-",
"StdVal": "110.5±0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. ⑥を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"最終確認は1度上下動作させ測定の事",
"規格:0.05㎜ (②③狙いは0~-0.01㎜)",
"①④は調整不可 (①④の差が大きい場合治具を確認する)"
],
"Tolks": [],
"Inspection... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. ⑥を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"最終確認は1度上下動作させ測定の事",
"規格:0.05㎜ (②③狙いは0~-0.01㎜)",
"①④は調整不可 (①④の差が大きい場合治具を確認する)"
],
"Tolks": [],
"Inspecti... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. ⑥を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"最終確認は1度上下動作させ測定の事",
"規格:0.05㎜ (②③狙いは0~-0.01㎜)",
"①④は調整不可 (①④の差が大きい場合治具を確認する)"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. ⑥を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"最終確認は1度上下動作させ測定の事",
"規格:0.05㎜ (②③狙いは0~-0.01㎜)",
"①④は調整不可 (①④の差が大きい場合治具を確認する)"
],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. ⑥を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"最終確認は1度上下動作させ測定の事",
"規格:0.05㎜ (②③狙いは0~-0.01㎜)",
"①④は調整不可 (①④の差が大きい場合治具を確認する)"
],
"Tolks": [],
"Inspec... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年校正対象外",
"ToolRecord": "校正成績書-",
"StdVal": "110.5±0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "昇降ﾌﾟﾚｰﾄ位置決め治具ｸﾗﾝﾌﾟﾌﾞﾚｰﾄﾞ押上板位置出し治具",
"Size": "",
"ToolOther": "FM-3165FM-3178",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. ⑥を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"最終確認は1度上下動作させ測定の事",
"規格:0.05㎜ (②③狙いは0~-0.01㎜)",
"①④は調整不可 (①④の差が大きい場合治具を確認する)"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3165FM-3178",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-2999FM-3167",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面調整",
"WorkItems": [
"1. ｱｼﾞｬｽﾄﾎﾞﾙﾄの平面度調整を行う"
],
"WorkPoints": [
"規格値:2.5±0.025㎜",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"3･4･6の高さ:1番を基準に平面度0.05㎜以内",
"2･5の高さ :1番を基準に-0.075~-0.... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面調整",
"WorkItems": [
"1. ｱｼﾞｬｽﾄﾎﾞﾙﾄの平面度調整を行う"
],
"WorkPoints": [
"規格値:2.5±0.025㎜",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"3･4･6の高さ:1番を基準に平面度0.05㎜以内",
"2･5の高さ :1番を基準に-0.075~-0.125㎜",
"7･8の高さ ... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "2.5±0.025㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受ﾌﾟﾚｰﾄ搭載面調整治具",
"Size": "",
"ToolOther": "FM-4128",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面調整",
"WorkItems": [
"1. ｱｼﾞｬｽﾄﾎﾞﾙﾄの平面度調整を行う"
],
"WorkPoints": [
"規格値:2.5±0.025㎜",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"3･4･6の高さ:1番を基準に平面度0.05㎜以内",
"2･5の高さ :1番を基準に-0.075~-0.125㎜",
"7･8の高さ... | {
"QualityItem": "平面度確認",
"ToolManageNo": "FM-4128",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2.5±0.025㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰﾌﾞﾗｹｯﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-2999FM-3227",
"WorkName": "ｸﾗﾝﾌﾟ部取付･位置出し調整",
"WorkItems": [
"1. ⑦に⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"手で軽く回って､0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事｡"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999FM-3227",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｸﾗﾝﾌﾟ部取付･位置出し調整",
"WorkItems": [
"1. ⑦に⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"手で軽く回って､0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事｡"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.02㎜",
"WorkName": "ｸﾗﾝﾌﾟ部取付･位置出し調整",
"WorkItems": [
"1. ⑦に⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"手で軽く回って､0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事｡"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "六角ﾎﾟｽﾄ取付",
"WorkItems": [
"1. ⑦に⑥を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P607ｶﾊﾞｰ取付",
"WorkItems": [
"1. ⑥にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N.m",
"WorkName": "P607ｶﾊﾞｰ取付",
"WorkItems": [
"1. ⑥にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞを実施する"
],
"WorkPoints": [
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:0.5~0.505MPa"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｴｱｰ圧力:0.5~0.505MPa",
"Method": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞを実施する"
],
"WorkPoints": [
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:0.5~0.505MPa"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｴﾗｰ無き事",
"Method": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. ｽﾋﾟｺﾝの調整､下図の回転数でA,B固定｡",
"2. 通常ｽﾋﾟｰﾄﾞで上記ｽﾋﾟｺﾝC,Dで調整｡",
"3. ｴｲｼﾞﾝｸﾞ実施",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"5. 速度調整後防錆油を塗布する｡"
],
"WorkPoints": [
"2000回動作実施"
],
"Tolks": [],
"Inspecti... | {
"QualityItem": "ｽﾋﾟｺﾝ回転量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "上昇時:全開下降時:全閉より2.5回転開ける事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. ｽﾋﾟｺﾝの調整､下図の回転数でA,B固定｡",
"2. 通常ｽﾋﾟｰﾄﾞで上記ｽﾋﾟｺﾝC,Dで調整｡",
"3. ｴｲｼﾞﾝｸﾞ実施",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"5. 速度調整後防錆油を塗布する｡"
],
"WorkPoints": [
"2000回動作実施"
],
"Tolks"... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "【通常ｽﾋﾟｰﾄﾞ】上昇時:1.30~1.40s下降時:1.45~1.55s【速度切替ﾓｰﾄﾞ】上昇時:0.25~0.45s下降時:1.20~1.40s1.25~1.45s",
"Method": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. ｽﾋﾟｺﾝの調整､下図の回転数でA,B固定｡",
"2. 通常ｽﾋﾟｰﾄﾞで上記ｽﾋﾟｺﾝC,Dで調整｡",
"3. ｴｲｼﾞﾝｸﾞ実施",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"5. 速度調整後防錆油を塗布する｡"
],
"WorkPoints": [
"2000回動作実施"
],
"Tolks"... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "【通常ｽﾋﾟｰﾄﾞ】上昇時:1.30~1.40s下降時:1.45~1.55s【速度切替ﾓｰﾄﾞ】上昇時:0.25~0.45s下降時:1.20~1.40s1.25~1.45s",
"Method": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "P613ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①にCOVER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "製造手配銘板の貼付",
"WorkItems": [
"1. ⑥のｾﾝｻｰﾄﾞｸﾞに①を貼付ける"
],
"WorkPoints": [
"脱脂後取付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1B1233P",
"1B1... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "製造手配銘板の貼付",
"WorkItems": [
"1. ⑥のｾﾝｻｰﾄﾞｸﾞに①を貼付ける"
],
"WorkPoints": [
"脱脂後取付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1B1233P",
"1B1234P",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P606銘板貼付",
"WorkItems": [
"1. COVER にSEAL を貼付ける"
],
"WorkPoints": [
"脱脂後取付けの事",
"各ﾚｰﾝ毎に貼付位置と方向が異なるので注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品の準備及びﾁｪｯｸ",
"WorkItems": [
"1. 付属品の準備とﾁｪｯｸ"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"各2(計4)",
"1120㎜×21620㎜×2",
"配管Ф6(黒)",
"準備",
... | {
"QualityItem": "準備確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに準備してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ運搬治具",
"Size": "",
"ToolOther": "FM-3168",
"WorkName": "ﾕﾆｯﾄ積み降ろし移動時の注意",
"WorkItems": [
"◆1. ﾕﾆｯﾄ移動時の注意",
"2. ﾍﾞｰｽﾌﾟﾚｰﾄに治具を取付ける"
],
"WorkPoints": [
"必ずFM-3168使用し移動させる事",
"ﾍﾞｰｽﾌﾟﾚｰﾄに治具ｼｬﾌﾄをねじ込んで使用する",
"取手をつかみﾕﾆｯﾄを移動させる"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3168",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.5N･m",
"WorkName": "ｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"3. PLATE にSTOPPER をSPACER BOLT WASHER で取付ける(4ヶ作成)",
"3. PLATE にSTOPPER をSPACER BOLT WASHER で取付ける(4ヶ作成)",
"4. 2･3完成品を①に㉒BOLT で取付ける"
],
"WorkPoints": [
"ﾍﾞｰｽﾌﾟﾚｰﾄに外当付けにて取付",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"4. 2･3完成品を①に㉒BOLT で取付ける"
],
"WorkPoints": [
"ﾍﾞｰｽﾌﾟﾚｰﾄに外当付けにて取付",
"取付方向に注意(ﾀｯﾌが見えること)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "拭取り確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに拭取りしている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立①",
"WorkItems": [
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"3. LEVER にBUSH を圧入",
"4. 3完成品にWASHER を挿入",
"5. 4完成品のLEVER 部分に防錆油を塗布",
"1. LEVER に砥石をかける"
],
"WorkPoints": [
"樹脂層側",
"BUSH の継ぎ目位置方向注意",
"BUSH WA... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕､傷等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｱﾙｶﾝｻｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立①",
"WorkItems": [
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"3. LEVER にBUSH を圧入",
"4. 3完成品にWASHER を挿入",
"5. 4完成品のLEVER 部分に防錆油を塗布",
"1. LEVER に砥石をかける"
],
"WorkPoints": [
"樹脂層側",
"BUSH の継ぎ目位置方向注意",
"BUSH WA... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車取付部ﾒﾀﾙ圧入治具",
"Size": "",
"ToolOther": "FM-2144",
"WorkName": "ﾚﾊﾞｰ組立①",
"WorkItems": [
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"3. LEVER にBUSH を圧入",
"1. LEVER に砥石をかける"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2144",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立①",
"WorkItems": [
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"3. LEVER にBUSH を圧入",
"4. 3完成品にWASHER を挿入",
"5. 4完成品のLEVER 部分に防錆油を塗布",
"1. LEVER に砥石をかける"
],
"WorkPoints": [
"樹脂層側",
"BUSH の継ぎ目位置方向注意",
"BUSH WA... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "圧入台",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立①",
"WorkItems": [
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"3. LEVER にBUSH を圧入",
"4. 3完成品にWASHER を挿入",
"5. 4完成品のLEVER 部分に防錆油を塗布",
"1. LEVER に砥石をかける"
],
"WorkPoints": [
"樹脂層側",
"BUSH の継ぎ目位置方向注意",
"BUSH WA... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り塗布出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "防錆油",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立②",
"WorkItems": [
"1. LEVER に砥石をかける",
"◆2. BUSH にｸﾞﾘｰｽを塗布",
"3. LEVER に2完成品を圧入",
"4. 3完成品をBOLT で固定",
"5. 4完成品のLEVER 部分に防錆油を塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置",
"BUSH には塗布しない",
"BUSH の継ぎ目位置方向注意... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕､傷等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｱﾙｶﾝｻｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立②",
"WorkItems": [
"1. LEVER に砥石をかける",
"◆2. BUSH にｸﾞﾘｰｽを塗布",
"3. LEVER に2完成品を圧入",
"4. 3完成品をBOLT で固定",
"5. 4完成品のLEVER 部分に防錆油を塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置",
"BUSH には塗布しない",
"BUSH の継ぎ目位置方向注意... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車取付部ﾒﾀﾙ圧入治具",
"Size": "",
"ToolOther": "FM-2144",
"WorkName": "ﾚﾊﾞｰ組立②",
"WorkItems": [
"3. LEVER に2完成品を圧入"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2144",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立②",
"WorkItems": [
"1. LEVER に砥石をかける",
"◆2. BUSH にｸﾞﾘｰｽを塗布",
"3. LEVER に2完成品を圧入",
"4. 3完成品をBOLT で固定",
"5. 4完成品のLEVER 部分に防錆油を塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置",
"BUSH には塗布しない",
"BUSH の継ぎ目位置方向注意... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "圧入台",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾚﾊﾞｰ組立②",
"WorkItems": [
"4. 3完成品をBOLT で固定"
],
"WorkPoints": [
"BUSH の継ぎ目位置方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立②",
"WorkItems": [
"1. LEVER に砥石をかける",
"◆2. BUSH にｸﾞﾘｰｽを塗布",
"3. LEVER に2完成品を圧入",
"4. 3完成品をBOLT で固定",
"5. 4完成品のLEVER 部分に防錆油を塗布"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置",
"BUSH には塗布しない",
"BUSH の継ぎ目位置方向注意... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り塗布出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "防錆油",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾋﾟﾝ圧入",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"PIN出代:3㎜",
"青矢印:PIN割り方向",
"1. ①に砥石をかけ､②を圧入",
"削除"
... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕､傷等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "圧入台",
"Size": "",
"ToolOther": "ｴｷｾﾝ",
"WorkName": "ﾋﾟﾝ圧入",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"PIN出代:3㎜",
"青矢印:PIN割り方向",
"1. ①に砥石をかけ､②を圧入",
"削除"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾋﾟﾝ圧入",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"PIN出代:3㎜",
"青矢印:PIN割り方向",
"1. ①に砥石をかけ､②を圧入",
"削除"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ組立",
"WorkItems": [
"1. BRACKET(L) に砥石をかけ､PIN を圧入",
"2. 1完成品にGUIDE をBOLT で取付",
"3. 2完成品にBOLT を取付"
],
"WorkPoints": [
"5㎜",
"取付注意:BOLT 穴付き側付属ﾅｯﾄで取付",
"取付寸法",
"青矢印:PIN割り方向",
"PIN出代:3.2㎜",
"G... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕､傷等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｱﾙｶﾝｻｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "圧入台",
"Size": "",
"ToolOther": "ｴｷｾﾝ",
"WorkName": "ﾌﾞﾛｯｸ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"出代:3.2mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ組立",
"WorkItems": [
"1. BRACKET(L) に砥石をかけ､PIN を圧入",
"2. 1完成品にGUIDE をBOLT で取付",
"3. 2完成品にBOLT を取付"
],
"WorkPoints": [
"青矢印:PIN割り方向",
"PIN出代:3.2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"Inspec... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾞﾛｯｸ組立",
"WorkItems": [
"1. BRACKET(L) に砥石をかけ､PIN を圧入",
"2. 1完成品にGUIDE をBOLT で取付",
"3. 2完成品にBOLT を取付"
],
"WorkPoints": [
"青矢印:PIN割り方向",
"PIN出代:3.2㎜"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜",
"ToolOther": "25.0N･m",
"WorkName": "ｼﾘﾝﾀﾞ―組立",
"WorkItems": [
"1. CYLINDER に付属品を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 25.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "25.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "14㎜",
"ToolOther": "10.0N･m",
"WorkName": "ｼﾘﾝﾀﾞ―組立",
"WorkItems": [
"2. 1完成品にJOINT を取付"
],
"WorkPoints": [
"ねじ込み後､絶対に戻さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞ―組立",
"WorkItems": [
"3. 2完成品にROD-END をNUT で仮取付"
],
"WorkPoints": [
"20㎜",
"穴の種類が異なる為､右側の穴が2段になっている方に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯﾄﾞｴﾝﾄﾞ出代調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6035",
"WorkName": "ｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整",
"WorkItems": [
"1. ①のｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整"
],
"WorkPoints": [
"ｽﾊﾟﾅを手前に回すとﾛｯﾄﾞｴﾝﾄﾞが縮み奥へ押しながら回すと伸びる方向になる",
"･調整を行う前に必ずｴｱｰ供給治具より ｴｱｰを入れておく事･ﾎｰｽは奥まで差込む",
"1㎜以下のｼｯｸﾈｽｹﾞｰｼﾞが通るように調整の事",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6035",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｰ供給治具",
"Size": "",
"ToolOther": "FM-2446",
"WorkName": "ｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整",
"WorkItems": [
"1. ①のｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整"
],
"WorkPoints": [
"ｽﾊﾟﾅを手前に回すとﾛｯﾄﾞｴﾝﾄﾞが縮み奥へ押しながら回すと伸びる方向になる",
"･調整を行う前に必ずｴｱｰ供給治具より ｴｱｰを入れておく事･ﾎｰｽは奥まで差込む",
"1㎜以下のｼｯｸﾈｽｹﾞｰｼﾞが通るように調整の事",
"17㎜の... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "1㎜",
"ToolOther": "",
"WorkName": "ｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整",
"WorkItems": [
"1. ①のｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整"
],
"WorkPoints": [
"ｽﾊﾟﾅを手前に回すとﾛｯﾄﾞｴﾝﾄﾞが縮み奥へ押しながら回すと伸びる方向になる",
"･調整を行う前に必ずｴｱｰ供給治具より ｴｱｰを入れておく事･ﾎｰｽは奥まで差込む",
"1㎜以下のｼｯｸﾈｽｹﾞｰｼﾞが通るように調整の事",
"17㎜のｽﾊ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1㎜以下が通るように調整する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "ﾘｰﾄﾞｽｲｯﾁ位置調整",
"WorkItems": [
"1. ①にSWITCH(400MM) を取付"
],
"WorkPoints": [
"※必ず点灯している事(目安7.5㎜)"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C20",
"InspectionItems": [
"検査表①:ｼﾘﾝﾀﾞL/S位置調整"
],
"Wor... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C20",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車駆動部制御ﾎﾞｯｸｽ",
"Size": "",
"ToolOther": "FM-2926",
"WorkName": "ﾘｰﾄﾞｽｲｯﾁ位置調整",
"WorkItems": [
"1. ①にSWITCH(400MM) を取付"
],
"WorkPoints": [
"※必ず点灯している事(目安7.5㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2926",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C20",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯﾄﾞｴﾝﾄﾞ出代調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6035",
"WorkName": "ﾘｰﾄﾞｽｲｯﾁ位置調整",
"WorkItems": [
"1. ①にSWITCH(400MM) を取付"
],
"WorkPoints": [
"※必ず点灯している事(目安7.5㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6035",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C20",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.8㎜",
"ToolOther": "10cN･m",
"WorkName": "ﾘｰﾄﾞｽｲｯﾁ位置調整",
"WorkItems": [
"1. ①にSWITCH(400MM) を取付"
],
"WorkPoints": [
"※必ず点灯している事(目安7.5㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾘｰﾄﾞｽｲｯﾁ位置調整",
"WorkItems": [
"1. ①にSWITCH(400MM) を取付"
],
"WorkPoints": [
"※必ず点灯している事(目安7.5㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "7.5±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [
"2. SWITCH のｽｲｯﾁﾚﾊﾞｰ組み替え",
"■1. SWITCH の型式確認し､ﾛｯﾄNo.を記録",
"3. JOINT を分け雄ねじ側を2完成品に取付",
"4. JOINT の雌ねじ側にCABLE の丸端子側の配線を通す",
"■5. SWITCH の蓋を開け､丸端子を挿入し指定ｶ所に接続する",
"6. 蓋及びJOINT を締め付ける"
],
... | {
"QualityItem": "型式･ﾛｯﾄ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C20",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "55cN･m",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [
"2. SWITCH のｽｲｯﾁﾚﾊﾞｰ組み替え",
"■1. SWITCH の型式確認し､ﾛｯﾄNo.を記録",
"3. JOINT を分け雄ねじ側を2完成品に取付"
],
"WorkPoints": [
"ﾚﾊﾞｰは180°反転させ取付",
"先端部を取外し本体を反時計回りに90度向き変更し取付"
],
"Tolks"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.