input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "駆動部組立8",
"WorkItems": [
"2. 1完成品に治具を取付ける",
"1. ①に③をBOLT WASHER で仮に取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"仮締めﾎﾞﾙﾄを締め付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 20.5N･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "駆動部組立8",
"WorkItems": [
"2. 1完成品に治具を取付ける",
"1. ①に③をBOLT WASHER で仮に取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"仮締めﾎﾞﾙﾄを締め付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 20.5N･m"
],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GW17)",
"Size": "",
"ToolOther": "FM-6422",
"WorkName": "駆動部組立8",
"WorkItems": [
"2. 1完成品に治具を取付ける",
"1. ①に③をBOLT WASHER で仮に取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"治具ﾎﾞﾙﾄ M10×45 M10小径FW",
"仮締めﾎﾞﾙﾄを締め付ける",
"FM-6422治具に 当付け"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6422",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部支持部位置決めｼﾞｸﾞ(NPM-GW17)",
"Size": "",
"ToolOther": "FM-6434",
"WorkName": "駆動部組立8",
"WorkItems": [
"2. 1完成品に治具を取付ける",
"1. ①に③をBOLT WASHER で仮に取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"治具ﾎﾞﾙﾄ M10×45 M10小径FW",
"仮締めﾎﾞﾙﾄを締め付ける",
"FM-6422治具に 当付け... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6434",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "15.5N･m",
"WorkName": "駆動部組立9",
"WorkItems": [
"1. ①のﾌﾞﾛｯｸを位置決めする"
],
"WorkPoints": [
"治具",
"治具に 当付け",
"PINに 当付け",
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [
"締付ﾄﾙｸ 15.5N･m"
],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "駆動部組立9",
"WorkItems": [
"1. ①のﾌﾞﾛｯｸを位置決めする"
],
"WorkPoints": [
"治具",
"治具に 当付け",
"PINに 当付け",
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [
"締付ﾄﾙｸ 15.5N･m"
],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GW17)",
"Size": "",
"ToolOther": "FM-6422",
"WorkName": "駆動部組立9",
"WorkItems": [
"1. ①のﾌﾞﾛｯｸを位置決めする",
"2. 治具を外す"
],
"WorkPoints": [
"治具",
"治具に 当付け",
"PINに 当付け",
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [
"締付ﾄﾙｸ 15.5N･m"
],
"Ins... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6422",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部支持部位置決めｼﾞｸﾞ(NPM-GW17)",
"Size": "",
"ToolOther": "FM-6434",
"WorkName": "駆動部組立9",
"WorkItems": [
"1. ①のﾌﾞﾛｯｸを位置決めする",
"2. 治具を外す"
],
"WorkPoints": [
"治具",
"治具に 当付け",
"PINに 当付け",
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [
"締付ﾄﾙｸ 15.5N･m"
]... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6434",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "駆動部組立10",
"WorkItems": [
"1. SHAFT にｸﾞﾘｰｽを塗布する",
"2. ②③を組合せ1完成品を挿入し①にSCREW で固定する"
],
"WorkPoints": [
"Dｶｯﾄ面位置で固定",
"ｼｬﾌﾄが端面より飛び出さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 310cN･m"
],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "310cN･m",
"WorkName": "駆動部組立10",
"WorkItems": [],
"WorkPoints": [
"Dｶｯﾄ面位置で固定",
"ｼｬﾌﾄが端面より飛び出さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 310cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "310cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "駆動部組立11",
"WorkItems": [
"2. SHAFT に付属品のCﾘﾝｸﾞを取付ける",
"◆1. BOLT SHAFT WASHER PLATE-WASHER SPRING にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"表裏に塗布",
"ｸﾞﾘｰｽを塗布位置",
"付属品",
"R付きの面をｼﾘﾝﾀﾞｰ側に向け取付",
"表裏に塗布"
],
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1、小豆粒:1小豆粒:3",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "駆動部組立12",
"WorkItems": [
"3. 増し締めする"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰ(ｼｬﾌﾄ)に不可なく締め付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
]... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "13㎜BOX",
"ToolOther": "12.7N･m",
"WorkName": "駆動部組立12",
"WorkItems": [
"1. ①にPLATE をBOLT WASHER で仮に取付ける",
"2. 1完成品に⑦を③④⑤⑥で取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [
"締付ﾄﾙｸ 12.7N･m"
],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "12.7N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "駆動部組立13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "160cN･m",
"WorkName": "駆動部組立13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｽｲｯﾁ取付(位置決め)",
"WorkItems": [
"2. 1完成品に治具を取付ける",
"3. ｽｲｯﾁの位置を合わせる"
],
"WorkPoints": [
"治具ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽｲｯﾁ取付(位置決め)",
"WorkItems": [
"2. 1完成品に治具を取付ける",
"3. ｽｲｯﾁの位置を合わせる"
],
"WorkPoints": [
"治具ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
]... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車確認SW取付位置決め治具(17連用右)",
"Size": "",
"ToolOther": "FM-6418",
"WorkName": "ｽｲｯﾁ取付(位置決め)",
"WorkItems": [
"1. ①に②をBOLT WASHER で仮に取付ける",
"2. 1完成品に治具を取付ける",
"3. ｽｲｯﾁの位置を合わせる"
],
"WorkPoints": [
"治具ﾎﾞﾙﾄ",
"治具に当付け",
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"ﾌﾟﾚｰﾄに当付け",
... | {
"QualityItem": "取付位置確認",
"ToolManageNo": "FM-6418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "SWのﾛｰﾗｰ部が治具に接している事",
"Method": "目視",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "配線・配管引き回",
"WorkItems": [],
"WorkPoints": [
"配管(白ﾗｲﾝ有)",
"配管に固定",
"配管にORIFICE-RING を挿入してからJOINTに挿入すること",
"285mmで固定する",
"配線がしっかりと固定され､挟み込み無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "配線ｺﾈｸﾀ先端までの出代:280±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "配線・配管引き回",
"WorkItems": [],
"WorkPoints": [
"配管(白ﾗｲﾝ有)",
"配管に固定",
"配管にORIFICE-RING を挿入してからJOINTに挿入すること",
"285mmで固定する",
"配線がしっかりと固定され､挟み込み無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された位置で固定する事:285±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "配線・配管引き回",
"WorkItems": [
"1. TUBE をｶｯﾄする",
"2. ①に1完成品と配線を接続し引き回して固定する",
"3. 2完成品にJOINT を挿入する"
],
"WorkPoints": [
"配線ｺﾈｸﾀ先端までの出代",
"白ﾗｲﾝ側をｶｯﾄする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りｶｯﾄしている事:165㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線・配管引き回",
"WorkItems": [
"1. TUBE をｶｯﾄする",
"2. ①に1完成品と配線を接続し引き回して固定する",
"3. 2完成品にJOINT を挿入する"
],
"WorkPoints": [
"配管(白ﾗｲﾝ有)",
"配管に固定",
"配線ｺﾈｸﾀ先端までの出代",
"配管にORIFICE-RING を挿入してからJOINTに挿入すること",
"白ﾗｲﾝ側... | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線・配管引き回",
"WorkItems": [
"1. TUBE をｶｯﾄする",
"2. ①に1完成品と配線を接続し引き回して固定する",
"3. 2完成品にJOINT を挿入する"
],
"WorkPoints": [
"配管(白ﾗｲﾝ有)",
"配管に固定",
"配線ｺﾈｸﾀ先端までの出代",
"配管にORIFICE-RING を挿入してからJOINTに挿入すること",
"白ﾗｲﾝ側... | {
"QualityItem": "配線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線がしっかりと固定され、挟み込み無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付",
"WorkItems": [
"1. ①にTUBE を挿入する",
"3. 2完成品に③TUBE を挿入する",
"◆2. ①にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ｽﾌﾟﾘﾝｸﾞのかけ方向に注意の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.6N･m",
"WorkName": "側面ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"2. 1完成品にPLATE をBOLT で取付ける",
"1. ①のCﾘﾝｸﾞを外す"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [
"締付ﾄﾙｸ 6.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｰ供給治具",
"Size": "",
"ToolOther": "FM-2446",
"WorkName": "ｼﾘﾝﾀﾞｰｽﾄﾛｰｸ調整",
"WorkItems": [
"1. ①にｴｱｰ供給治具を接続する",
"2. ｼﾘﾝﾀﾞｰを動作させ隙間を確認する",
"1. ①にｴｱｰ供給治具を接続する",
"2. ｼﾘﾝﾀﾞｰを動作させ隙間を確認する",
"3. ｶﾞｲﾄﾞから治具端面までの隙間を確認"
],
"WorkPoints": [
"SD-A052311-005を参照の事",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｽﾄﾛｰｸ調整治具",
"Size": "",
"ToolOther": "FM-3061",
"WorkName": "ｼﾘﾝﾀﾞｰｽﾄﾛｰｸ調整",
"WorkItems": [
"3. ｶﾞｲﾄﾞから治具端面までの隙間を確認"
],
"WorkPoints": [
"隙間がある事",
"位置確認後速やかに治具を取外す事治具を取付けたまま動作すると破損の恐れ有り",
"ｼｯｸﾈｽｹﾞｰｼﾞ挿入方向",
"0.5mmが通ら無い事"
],
"Tolks": [],
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.5㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰｽﾄﾛｰｸ調整",
"WorkItems": [
"3. ｶﾞｲﾄﾞから治具端面までの隙間を確認"
],
"WorkPoints": [
"隙間がある事",
"位置確認後速やかに治具を取外す事治具を取付けたまま動作すると破損の恐れ有り",
"ｼｯｸﾈｽｹﾞｰｼﾞ挿入方向",
"0.5mmが通ら無い事"
],
"Tolks": [],
"InspectionNo": "... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GW17)",
"Size": "",
"ToolOther": "FM-6422",
"WorkName": "ｼﾘﾝﾀﾞｰｽﾄﾛｰｸ調整",
"WorkItems": [
"1. ①にｴｱｰ供給治具を接続する",
"2. ｼﾘﾝﾀﾞｰを動作させ隙間を確認する",
"3. ｶﾞｲﾄﾞから治具端面までの隙間を確認"
],
"WorkPoints": [
"SD-A052311-005を参照の事",
"ｼﾘﾝﾀﾞｰが出限である事",
"隙間がある事",
"位置確認後速... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6422",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①にGUIDE をSPACER BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.6cN･m",
"WorkName": "ｶﾞｲﾄﾞ取付(前側&左側&台車)",
"WorkItems": [],
"WorkPoints": [
"治具に当付ける",
"ﾌﾞﾗｹｯﾄに不可なく締め付けの事",
"t:0.2㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"治具を取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 3.6cN･m"
],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.2㎜",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付(前側&左側&台車)",
"WorkItems": [],
"WorkPoints": [
"治具に当付ける",
"ﾌﾞﾗｹｯﾄに不可なく締め付けの事",
"t:0.2㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"治具を取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 3.6cN･m"
],
"InspectionNo": "WETE-G002-C17",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ASF34連交換台車用ｶﾞｲﾄﾞ位置決めｼﾞｸﾞ左側",
"Size": "",
"ToolOther": "FM-6623",
"WorkName": "ｶﾞｲﾄﾞ取付(前側&左側&台車)",
"WorkItems": [],
"WorkPoints": [
"治具に当付ける",
"ﾌﾞﾗｹｯﾄに不可なく締め付けの事",
"t:0.2㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"治具を取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 3.6cN･m"
],
"InspectionNo": "... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6623",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.6cN･m",
"WorkName": "ｶﾞｲﾄﾞ取付(後側&左側&台車)",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"治具に当付ける",
"t:0.2㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6cN･m"
],
"Inspectio... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.2㎜",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付(後側&左側&台車)",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"治具に当付ける",
"t:0.2㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6cN･m"
],
"Inspection... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ASF34連交換台車用ｶﾞｲﾄﾞ位置決めｼﾞｸﾞ左側",
"Size": "",
"ToolOther": "FM-6623",
"WorkName": "ｶﾞｲﾄﾞ取付(後側&左側&台車)",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"治具に当付ける",
"t:0.2㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6cN･m"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6623",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に⑥or⑪をBOLT WASHER or㉓BOLT で取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"前&左側&台車後&左側&台車に取付の事(ﾌﾞﾗｹｯﾄは同じ部品です)",
"仕様確認の事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6cN･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW で取付ける"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"前側&左側&台車 仕様で表示しています",
"後側&左側&台車 仕様も同様に取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GW17)",
"Size": "",
"ToolOther": "FM-6422",
"WorkName": "ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW で取付ける",
"2. 位置決め治具を取り外しｽﾀﾝﾄﾞ治具から下ろす"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています",
"前側&左側&台車 仕様で表示しています",
"後側&左側&台車 仕様も同様に取付けの事"
],
"Tolks":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6422",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部材17連/34連左側",
"WorkItems": [
"1. 次工程へ払い出す"
],
"WorkPoints": [
"◆以下仕様の場合､必要員数を払い出す事 ･ITF17連/ASF34連交換台車対応ﾕﾆｯﾄ(前側&右側)仕様 ･ITF17連/ASF34連交換台車対応ﾕﾆｯﾄ(後側&右側)仕様 ･ITF17連/ASF34連交換台車対応ﾕﾆｯﾄ(前側&右側&ﾄﾚｲ)NPM-GW仕様 ･ITF17連/ASF34連交換台車対応ﾕﾆｯﾄ(後... | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】Y軸LMｶﾞｲﾄﾞ仮取付け",
"WorkItems": [
"1. LINEAR-WAY の下面・スライダー上面に㉖をかける",
"2. LINEAR-WAY の防錆油･ｸﾞﾘｰｽ･ｺﾞﾐの除去を行う",
"◆3. LINEAR-WAY を架台に搭載しBOLT で仮締めをする"
],
"WorkPoints": [
"LMｶﾞｲﾄﾞ下面",
"ｽﾗｲﾀﾞｰ上面",
"手袋着用し作業する事",
... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取扱",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸LMｶﾞｲﾄﾞ押え治具",
"Size": "",
"ToolOther": "FM-4598",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [],
"WorkPoints": [
"治具取付けｲﾒｰｼﾞ",
"㉗とLMガイドの間に㉘を挟み込む"
],
"Tolks": [
"締付ﾄﾙｸ 2.4N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes"... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4598",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸LMｶﾞｲﾄﾞ押えｼﾞｸﾞｽﾍﾟｰｻ",
"Size": "",
"ToolOther": "FM-5069",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [
"4. LMｶﾞｲﾄﾞと当て面に隙間が無いことを確認する",
"1. ㉗を取付用ボルトで架台に固定する",
"3. LMｶﾞｲﾄﾞに仮締めしてあるﾎﾞﾙﾄを本締付けする",
"2. ㉗の押し当て用ボルトを締付けてLMガイドに当付ける"
],
"WorkPoints": [
"治具取付けｲﾒｰｼﾞ",
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5069",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "2.4N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [
"1. ㉗を取付用ボルトで架台に固定する",
"2. ㉗の押し当て用ボルトを締付けてLMガイドに当付ける"
],
"WorkPoints": [
"取付用ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.4N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [],
"WorkPoints": [
"治具取付けｲﾒｰｼﾞ",
"㉗とLMガイドの間に㉘を挟み込む"
],
"Tolks": [
"締付ﾄﾙｸ 2.4N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "26.5N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [
"3. LMｶﾞｲﾄﾞに仮締めしてあるﾎﾞﾙﾄを本締付けする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 26.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"W... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [
"4. LMｶﾞｲﾄﾞと当て面に隙間が無いことを確認する"
],
"WorkPoints": [
"0.03mmｹﾞｰｼﾞが入らないこと",
"隙間確認後､FRONT作業者と入れ替わり増し締め確認を行う"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-C02",
"InspectionIte... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜ｹﾞｰｼﾞが入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽﾄﾚｰﾄｴｯｼﾞ置台",
"Size": "",
"ToolOther": "FM-4596",
"WorkName": "Y軸LMｶﾞｲﾄﾞ真直度測定",
"WorkItems": [
"3. ｽﾄﾚｰﾄｴｯｼﾞにﾀﾞｲﾔﾙｹﾞｰｼﾞをｾｯﾃｨﾝｸﾞする",
"4. ｽﾗｲﾀﾞｰを可動させ両端の値が0になるようにｽﾄﾚｰﾄｴｯｼﾞ位置を調整する",
"◆6. ㉙㉚を外し、㉗を降ろし、㉖を取り外す",
"5. 検査書に基づきﾘﾆｱｶﾞｲﾄﾞの真直度を測定し結果を検査書に記入する"
],
"WorkPoints": [
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4596",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取扱",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸LMｶﾞｲﾄﾞ真直度測定",
"WorkItems": [
"2. 両端のﾘﾆｱｽﾗｲﾀﾞｰに㉙㉚を取付ける",
"◆1. 架台側面に㉖を取付けその上に㉗を置く"
],
"WorkPoints": [
"Front側",
"搭載時二人作業"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-C02",
"InspectionItems... | {
"QualityItem": "真直度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.03㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸平行度測定治具",
"Size": "",
"ToolOther": "FM-4834",
"WorkName": "【WX専用】Y軸LMｶﾞｲﾄﾞ平行度測定",
"WorkItems": [
"2. ﾚｰﾙにﾀﾞｲﾔﾙｹﾞｰｼﾞをｾｯﾃｨﾝｸﾞする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4834",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "【WX専用】Y軸LMｶﾞｲﾄﾞ平行度測定",
"WorkItems": [
"2. ﾚｰﾙにﾀﾞｲﾔﾙｹﾞｰｼﾞをｾｯﾃｨﾝｸﾞする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEAV-G002-C02",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Word... | {
"QualityItem": "真直度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ取付面余白ｸﾞﾘｰｽ塗布",
"WorkItems": [
"◆1. LMｶﾞｲﾄﾞ取付面余白にｸﾞﾘｰｽを薄く伸ばしながら塗布する"
],
"WorkPoints": [
"この面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に薄く伸ばしながら塗布",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】Y軸LMｶﾞｲﾄﾞｼﾘｱﾙNo確認及び摺動抵抗測定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. LMｶﾞｲﾄﾞのｼﾘｱﾙNoを確認し､検査書に記入する",
"2. 摺動抵抗を... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WEAV-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】Y軸LMｶﾞｲﾄﾞｼﾘｱﾙNo確認及び摺動抵抗測定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. LMｶﾞｲﾄﾞのｼﾘｱﾙNoを確認し､検査書に記入する",
... | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "Peak値:50N以下",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "13㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ固定ﾎﾟｽﾄ取付け",
"WorkItems": [
"1. 前準備完成品 を架台に取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ取付け",
"WorkItems": [
"1. MANIFOLD をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ切替SW中継ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｶﾒﾗｹｰﾌﾞﾙ固定ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. 前準備完成品 を⑯⑰で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾄﾞﾛｱ中継ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET をWASHER BOLT にて取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ取付け",
"WorkItems": [
"2. 前準備完成品 をBOLT WASHER にて取付ける",
"◆1. 前準備完成品 を架台に投入する"
],
"WorkPoints": [
"矢印方向に回転させながら投入していく",
"FRONT側にACｹｰﾌﾞﾙを送りながら投入していく",
"ｹｰﾌﾞﾙ挟み込み注意!!"
],
"Tolks": [
"締付ﾄ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ引き回し(OP:17連切替仕様、ﾄﾚｲ仕様あり)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"TRAY.PR",
"ﾄﾞﾗｲﾊﾞ... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾊﾞｰﾌﾞﾗｹｯﾄ･ﾒｲﾝｽｲｯﾁ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5260",
"WorkName": "ﾄﾚｲｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付(OP:17連切替仕様、ﾄﾚｲ仕様)",
"WorkItems": [
"2. 前準備完成品 を⑯⑰で取付ける"
],
"WorkPoints": [
"貼付ける前に清掃し向きに注意して貼付けること",
"㉚を下図の様に取付ける",
"前準備完成品 を前方向に押し当てて固定する",
"ﾏｽｷﾝｸﾞ領域の右上に貼付ける"
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5260",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾄﾚｲｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付(OP:17連切替仕様、ﾄﾚｲ仕様)",
"WorkItems": [
"2. 前準備完成品 を⑯⑰で取付ける"
],
"WorkPoints": [
"貼付ける前に清掃し向きに注意して貼付けること",
"㉚を下図の様に取付ける",
"前準備完成品 を前方向に押し当てて固定する",
"ﾏｽｷﾝｸﾞ領域の右上に貼付ける"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+ﾋﾞｯﾄ",
"ToolOther": "180cN･m",
"WorkName": "ﾄﾚｲ電源ｹｰﾌﾞﾙ接続(OP:17連切替仕様、ﾄﾚｲ仕様)",
"WorkItems": [
"1. ﾄﾚｲ電源ｹｰﾌﾞﾙを固定し中継ｺﾈｸﾀに接続する",
"2. SCREW にてFGｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"TRAY.PR",
"しっかり差込まれているか押して確認する",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｰ",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰ取付け",
"WorkItems": [
"1. LABEL を架台に貼付ける",
"4. 前準備完成品 をBOLT WASHER にて取付ける",
"3. 前準備完成品 をBOLT WASHER にて取付ける",
"2. 前準備完成品 をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"貼付ける前に清掃し向きに注意して貼付けること",
"前準備完成品 ｺﾝ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示の位置に貼付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜ﾛﾝｸﾞ",
"ToolOther": "6.0N･m",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰ取付け",
"WorkItems": [
"4. 前準備完成品 をBOLT WASHER にて取付ける",
"3. 前準備完成品 をBOLT WASHER にて取付ける",
"2. 前準備完成品 をBOLT WASHER にて取付ける",
"4. 前準備完成品 をBOLT WASHER にて取付ける",
"3. 前準備完成品 をBOLT WASHER にて取付ける",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜ﾛﾝｸﾞ",
"ToolOther": "3.2N･m",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰ取付け",
"WorkItems": [
"4. 前準備完成品 をBOLT WASHER にて取付ける",
"3. 前準備完成品 をBOLT WASHER にて取付ける",
"2. 前準備完成品 をBOLT WASHER にて取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+ﾋﾞｯﾄ",
"ToolOther": "120cN･m",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰAC接続",
"WorkItems": [
"3. ｺﾝﾃﾞﾝｻBOX⇔ﾄﾞﾗｲﾊﾞｰ接続ｹｰﾌﾞﾙを固定する",
"■1. FG線を①にて架台に取付ける",
"2. XYﾄﾞﾗｲﾊﾞｰ･ｺﾝﾃﾞﾝｻｰBOXにACｹｰﾌﾞﾙ･ﾌｧｲﾊﾞｰ及びｱｰｽ線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+ﾋﾞｯﾄ",
"ToolOther": "180cN･m",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰAC接続",
"WorkItems": [
"3. ｺﾝﾃﾞﾝｻBOX⇔ﾄﾞﾗｲﾊﾞｰ接続ｹｰﾌﾞﾙを固定する",
"■1. FG線を①にて架台に取付ける",
"2. XYﾄﾞﾗｲﾊﾞｰ･ｺﾝﾃﾞﾝｻｰBOXにACｹｰﾌﾞﾙ･ﾌｧｲﾊﾞｰ及びｱｰｽ線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰAC接続",
"WorkItems": [
"3. ｺﾝﾃﾞﾝｻBOX⇔ﾄﾞﾗｲﾊﾞｰ接続ｹｰﾌﾞﾙを固定する",
"■1. FG線を①にて架台に取付ける",
"2. XYﾄﾞﾗｲﾊﾞｰ･ｺﾝﾃﾞﾝｻｰBOXにACｹｰﾌﾞﾙ･ﾌｧｲﾊﾞｰ及びｱｰｽ線を接続する"
],
"WorkPoints": [
"P1AK514⇒CN1PA",
"P1BK514⇒CN1PB",
"L1K504⇒CN... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "中継基板取付治具(搬送基板用)",
"Size": "",
"ToolOther": "FM-4668",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 3.2N･m",
"... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4668",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "180cN･m",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "BOX7㎜",
"ToolOther": "3.2N･m",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"4. 前準備完成品 を取付ける",
"★5. 前準備完成品 をWASHER BOLT ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 180cN･m"... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"REAR",
"搬送中継基板",
"I/O中継基板",
"治具㉘使... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示の位置に貼付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜ﾛﾝｸﾞ",
"ToolOther": "6.0N･m",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰ配線用ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET をBOLT WASHER にて取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "天板ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. 前準備完成品 をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"4ヵ所取付け"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ取付け",
"WorkItems": [
"1. 前準備完成品 or前準備完成品 or前準備完成品 をBOLT WASHER で取付ける",
"2. 継手に付属のFT-11を架台に挿し込み固定する"
],
"WorkPoints": [
"真直ぐに押し込む",
"30連台車仕様以外",
"17連台車/17連切替仕様時は前準備完成品 ､30連台車仕様時は前準備完成品 ､ﾄﾚｲ仕様時... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｴｱｰ供給部ｸﾞﾛﾒｯﾄ取付け",
"WorkItems": [
"1. GROMMET を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾒｲﾝｴｱｰﾕﾆｯﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"締付ﾄﾙｸ 9.8N･m",
"4φ TUBE",
"JOINT... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｴｱｰﾕﾆｯﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"締付ﾄﾙｸ 9.8N･m",
"4φ TUBE",
"JOINTに差込む",
"... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾒｲﾝｴｱｰ圧ｾﾝｻｰ取付け",
"WorkItems": [
"1. 前準備完成品 を⑯⑰で取付ける"
],
"WorkPoints": [
"㉚を下図の様に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付治具",
"Size": "",
"ToolOther": "FM-4970",
"WorkName": "ﾒｲﾝｴｱｰ圧ｾﾝｻｰ取付け",
"WorkItems": [
"2. ㉙治具を使用し⑥を架台に貼付ける"
],
"WorkPoints": [
"貼付ける前に清掃し向きに注意して貼付けること",
"前準備完成品 を横方向ｾﾝﾀｰ合わせにし､前方向に押し当てて固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-4970",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の位置に貼付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾊﾞｰﾌﾞﾗｹｯﾄ･ﾒｲﾝｽｲｯﾁ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5260",
"WorkName": "ﾒｲﾝｴｱｰ圧ｾﾝｻｰ取付け",
"WorkItems": [
"1. 前準備完成品 を⑯⑰で取付ける"
],
"WorkPoints": [
"㉚を下図の様に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5260",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付治具",
"Size": "",
"ToolOther": "FM-4970",
"WorkName": "【WX専用】感電注意・ｾﾝｻｰ中継ｼｰﾙ貼付",
"WorkItems": [
"2. 治具を使用しLABEL (R/R)を架台に貼付ける",
"3. 治具を使用しLABEL (R/L)を架台に貼付ける",
"1. 治具を使用しLABEL を架台に貼付ける",
"2. 治具を使用しLABEL (R/R)を架台に貼付ける",
"3. 治具を使用しLABEL (R/L)を架台に貼付ける",
"1. 治具を... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-4970",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の位置に貼付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付治具",
"Size": "",
"ToolOther": "FM-4970",
"WorkName": "真空ﾎﾟﾝﾌﾟ・高温注意・FGｼｰﾙ貼付",
"WorkItems": [
"1. LABEL LABEL を架台に貼付ける",
"2. LABEL を架台に貼付ける",
"1. LABEL LABEL を架台に貼付ける",
"2. LABEL を架台に貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-4970",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の位置に貼付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊﾟﾜｰﾕﾆｯﾄｺﾈｸﾀｰ保護ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6814",
"WorkName": "束線投入準備①",
"WorkItems": [
"1. ㉖㉗をFT11に取付ける",
"2. ㉘を⑳で取付ける"
],
"WorkPoints": [
"取付けのみ｡ｲﾝｼｭﾛｯｸは縛らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-6814",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "束線投入準備①",
"WorkItems": [
"1. ㉖㉗をFT11に取付ける",
"2. ㉘を⑳で取付ける"
],
"WorkPoints": [
"取付けのみ｡ｲﾝｼｭﾛｯｸは縛らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入準備②",
"WorkItems": [
"1. REAR側にて前準備完成品 束線を図のように展開する"
],
"WorkPoints": [
"FRONT側へ投入するｹｰﾌﾞﾙ",
"CAF,CAR",
"R4204R",
"B0235R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入準備③(ﾄﾚｲｹｰﾌﾞﾙ追加)(OP:17連切替仕様、ﾄﾚｲ仕様)",
"WorkItems": [
"1. 前準備完成品 束線に②③⑥⑦を追加する"
],
"WorkPoints": [
"FRONT側へ投入するｹｰﾌﾞﾙ",
"CAF,CAR",
"黄色ﾏｰｸを末端の白ｲﾝｼｭﾛｯｸに合わせる",
"R4204R",
"B0235R",
"FOS5Pに長さを合わせる",
"FOS5... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入準備⑤(基板ﾎﾙﾀﾞｰｹｰﾌﾞﾙ追加)(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ奥基準仕様)",
"WorkItems": [
"1. 前準備完成品 束線に②③④⑥を追加する"
],
"WorkPoints": [
"FRONT側へ投入するｹｰﾌﾞﾙ",
"TMに長さを合わせる",
"UP1に長さを合わせる",
"2A133A13",
"CART.1",
"TM",
"ﾃﾞ... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入準備⑥(ｹｰﾌﾞﾙ追加)(OP:F側ﾄﾚｲｽﾄｯｶｰ仕様)",
"WorkItems": [
"1. ①束線にCABLE CABLE CABLE を追加する"
],
"WorkPoints": [
"既存のBL_K322に長さを合わせる",
"既存のBL_K321FA3_K321に長さを合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入準備⑦(追加ｹｰﾌﾞﾙ固定)",
"WorkItems": [
"1. 追加したｹｰﾌﾞﾙを束線に固定する"
],
"WorkPoints": [
"FRONT側へ投入するｹｰﾌﾞﾙ",
"ｴﾝｺｰﾀﾞｰｹｰﾌﾞﾙを一緒に固定しないように注意する事",
"仕様によりｲﾝｼｭﾛｯｸ固定位置が異なります",
"CART.1ｹｰﾌﾞﾙの一番端のFT11から150mmの位置にCABLE-SUPPORT と一緒に固定する",... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "束線投入準備⑦(追加ｹｰﾌﾞﾙ固定)",
"WorkItems": [
"1. 追加したｹｰﾌﾞﾙを束線に固定する"
],
"WorkPoints": [
"FRONT側へ投入するｹｰﾌﾞﾙ",
"ｴﾝｺｰﾀﾞｰｹｰﾌﾞﾙを一緒に固定しないように注意する事",
"仕様によりｲﾝｼｭﾛｯｸ固定位置が異なります",
"CART.1ｹｰﾌﾞﾙの一番端のFT11から150mmの位置にCABLE-SUPPORT と一緒... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "150㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入",
"WorkItems": [
"◆1. REAR側より束線を投入し中央板両端の穴よりFRONT側ｹｰﾌﾞﾙを配線する"
],
"WorkPoints": [
"1A03､その他",
"CART.F1､その他",
"TRAY.SR､その他",
"1A04､その他",
"非常停止ｽｲｯﾁの端子を曲げないように注意すること",
"ｺﾈｸﾀやｹｰﾌﾞﾙを架台に引っ掛けないように注意する"
]... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取扱",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定①(中央)",
"WorkItems": [
"1. 中央部のｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"最初にこの位置(間隔が狭い白ｲﾝｼｭﾛｯｸ間)を基準として固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Wor... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定④(右側)(OP:R側ﾏﾙﾁ認識ｶﾒﾗ無し仕様あり)",
"WorkItems": [
"1. 右側用束線を架台に固定する"
],
"WorkPoints": [
"穴から外側へ出す",
"R側ﾏﾙﾁ認識ｶﾒﾗ無し仕様の場合はここでまとめて固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes"... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾛﾒｯﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"1. ﾍﾞｰｽ上に上がって来ているｹｰﾌﾞﾙを前準備完成品 に通し､ﾍﾞｰｽ穴に嵌め込む",
"ｹｰﾌ... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ・廃棄BOX・(基板ﾎﾙﾀﾞｰ・幅寄せﾓｰﾀｰ)ｹｰﾌﾞﾙ固定・引き回し(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ奥基準仕様あり)",
"WorkItems": [
"1. ｹｰﾌﾞﾙを架台に固定する",
"2. ﾍﾞｰｽ上にｹｰﾌﾞﾙB1110Rを出す",
"3. ﾍﾞｰｽ上にｹｰﾌﾞﾙB11P他を出す",
"5. ﾍﾞｰｽ上にｹｰﾌﾞﾙB1726/7R､B4713/4/5R及びM629を出す",
... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ接続(SIO基板)(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様あり)",
"WorkItems": [
"1. SIO基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"準備工程で接続､名称確認のみ",
"流れ方向によって接続するｺﾈｸﾀが異なるので注意する事",
"･ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時"
],
"Tolks": [],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.