input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し2",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"YMM504",
"U/V/W(A)/E2K504"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し3",
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に702Rを書く"
],
"WorkPoints": [
"Φ8白配管(下)",
"Φ8白配管(下)"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し4",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"XMM/EM503",
"U/V/W/E2K503"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し5",
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に701Rを書く"
],
"WorkPoints": [
"Φ8白配管(上)",
"Φ8白配管(上)"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し6",
"WorkItems": [
"1. ①を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CMRP",
"4K303",
"ｺﾈｸﾀの向きに注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "ﾊｰﾈｽ引き回確認1",
"WorkItems": [
"1. ﾊｰﾈｽの引き回しを確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"U/V/W(B)/K504",
"U/V/W(A)/K... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "内側配線前準備",
"WorkItems": [
"1. CABLE-SUPPORT CABLE-SUPPORT にインシュロックを挿入し㉖に取付ける"
],
"WorkPoints": [
"ｹｰﾌﾞﾙｻﾎﾟｰﾄの向き注意",
"ｲﾝｼｭﾛｯｸをｹｰﾌﾞﾙｻﾎﾟｰﾄに通す方向は下図の通りとする"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し7",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"YEM508",
"CN2BK504"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し8",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"YEM504",
"CN2AK504"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し9",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"1A22",
"CN6",
"HRPWA11"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し10",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CN1",
"HR_K313"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し11",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に2... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し12",
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に302を書く"
],
"WorkPoints": [
"Φ6黄配管",
"Φ6黄配管"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し13",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"XEM503",
"CN2K503"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し14",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CN7",
"B113R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "ﾊｰﾈｽ引き回し確認2",
"WorkItems": [
"1. ﾊｰﾈｽの引き回しを確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"HRPWA11②",
"CN2K503",
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布1",
"WorkItems": [
"◆1. CABLE-BEAR CABLE-BEAR 付属のリングプレートの内側に㉖を塗布する"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布後紛失注意",
"ﾑﾗ･だまが無いように指で均等に塗り広げること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1枚当たり各1/2(0.05g)",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽKS-63W",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1ﾘﾝｸ当たり各1 (0.1g)",
"◆1. CABLE-BEAR CABLE-BEAR のベアの... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1ﾘﾝｸ当たり各1(0.1g)",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽKS-63W",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布3",
"WorkItems": [
"◆2. ①②の下記指示部に㉗を塗布する",
"1. ①②のｹｰﾌﾞﾙｻﾎﾟｰﾄにｲﾝｼｭﾛｯｸを通す(1枚2箇所×8枚)"
],
"WorkPoints": [
"あらかじめ塗る総量を出しておき､すべて使い切って塗布すること",
"ﾑﾗ･だまが無いように手で均等に塗り広げること",
"2.4g",
"1.6g",
"3.2g",
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1ｹｰﾌﾞﾙ当たり各4(0.4g)",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽKS-63W",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾍﾞｱ取付け",
"WorkItems": [
"1. ①のX軸用ｹｰﾌﾞﾙﾍﾞｱをｾｯﾄする",
"3. ②の外側ｹｰﾌﾞﾙｻﾎﾟｰﾄの固定側を固定する",
"4. ②の外側ｹｰﾌﾞﾙｻﾎﾟｰﾄの可動側を固定する",
"5. 付属のｱｰﾑを取付ける",
"2. ②の内側ｹｰﾌﾞﾙｻﾎﾟｰﾄを固定する"
],
"WorkPoints": [
"X軸ｹｰﾌﾞﾙﾍﾞｱ外側",
"下図に示す部分をｹｰﾌﾞ... | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示された位置で結束が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾍﾞｱ取付け",
"WorkItems": [
"1. ①のY軸用ｹｰﾌﾞﾙﾍﾞｱをｾｯﾄする",
"3. ②の外側ｹｰﾌﾞﾙｻﾎﾟｰﾄの可動側を固定する",
"4. ②の外側ｹｰﾌﾞﾙｻﾎﾟｰﾄの固定側を固定する",
"5. 付属のｱｰﾑを取付ける",
"2. ②の内側ｹｰﾌﾞﾙｻﾎﾟｰﾄを固定する"
],
"WorkPoints": [
"Y軸ｹｰﾌﾞﾙﾍﾞｱ外側",
"下図に示す部分をｹｰﾌﾞ... | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示された位置で結束が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "外観確認",
"WorkItems": [
"1. ①の外観を確認する"
],
"WorkPoints": [
"CN6",
"1A22",
"黄色配管",
"黒色配管",
"CN1",
"XEM503",
"Y軸ﾍﾞｱ",
"X軸ﾍﾞｱ",
"XMM/EM503",
"4K303",
"白色配管",
"U/V/W/E2K503",
... | {
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管によじれが無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け(架台正面右下ｶﾊﾞｰ)",
"WorkItems": [
"1. COVER へLABEL LABEL LABEL を貼付ける",
"2. 1の完成品へLABEL を添付する"
],
"WorkPoints": [
"貼付けはし無い事 ※台紙のまま添付のみ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け(架台背面左下ｶﾊﾞｰ)",
"WorkItems": [
"1. COVER へLABEL LABEL を貼付ける",
"2. 1完成品の裏面にLABEL を貼付"
],
"WorkPoints": [
"ｵﾓﾃ",
"ｳﾗ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": []... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け(架台正面左下ｶﾊﾞｰ)",
"WorkItems": [
"1. COVER へLABEL LABEL を貼付ける"
],
"WorkPoints": [
"ｵﾓﾃ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"107mm"... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け(架台背面右下ｶﾊﾞｰ)",
"WorkItems": [
"1. ①へ⑥⑦を貼付ける"
],
"WorkPoints": [
"ｵﾓﾃ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"107mm",
"30mm",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞｯｼｭ取付け【OP:ITF17連/ASF34連交換台車切替ﾕﾆｯﾄ】",
"WorkItems": [
"1. ①②にBUSH BUSH を取付ける"
],
"WorkPoints": [
"BUSH を先に取付ける",
"交換台車切替ﾕﾆｯﾄ(前側仕様時)",
"交換台車切替ﾕﾆｯﾄ(後側仕様時)",
"仕様により取付け作業を行う事",
"BUSH に当付けて取付ける"
],
"Tolks": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し(ﾒｲﾝｴｱｰﾊﾞﾙﾌﾞｶﾊﾞｰ)",
"WorkItems": [
"1. COVER をH2工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し(供給部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し(本体部)",
"WorkItems": [
"1. SCREW をH2工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し(付属品)",
"WorkItems": [
"1. BRACKET BRACKET BOLT CAP CASE Caution sheet (Maintenance) Nozzle Shaft Cleaning Tool(Silicon Type):FC GREASE COUPLER をH2工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Insp... | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立①",
"WorkItems": [
"▲1. PLATE にSPACER ･SPACER ･SPACER ･SPACER ･SPACER ･SPACER ･SPACER ･SPACER をSCREW ･SCREW で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立②",
"WorkItems": [
"1. ①に②･CABLE ･CABLE を⑯･⑰･⑱で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立①",
"WorkItems": [
"1. ①に②･③を圧入し④を組付け",
"2. ⑤に1.完成品を⑯･⑰で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立①",
"WorkItems": [
"1. ①に②･③を圧入し④を組付け",
"2. ⑤に1.完成品を⑯･⑰で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:9.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立②",
"WorkItems": [
"1. ①に②を⑯･⑰で組付け",
"2. 1.完成品に⑱･⑲を組付け"
],
"WorkPoints": [
"方向注意!!円の接線に平行に組付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
]... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立③",
"WorkItems": [
"1. ①に②を圧入",
"2. 1.完成品に③を挿入し④を⑯･⑰で組付け",
"3. ⑤に⑥を組付け",
"4. 2.完成品に3.完成品を⑱で組付け",
"1. ①に②を圧入",
"2. 1.完成品に③を挿入し④を⑯･⑰で組付け",
"3. ⑤に⑥を組付け",
"4. 2.完成品に3.完成品を⑱で組付け"
],
"WorkPoin... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代(合計8個):3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. ①にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"2. 1.完成品にPOST を挿入し④をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当て... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"特殊工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. ①にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"2. 1.完成品にPOST を挿入し④をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当て... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.2~1.5N･m",
"WorkName": "θ軸部組立④",
"WorkItems": [],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当てて組付け",
"4面共組付け(計4個)"
],
"Tolks": [
"締付ﾄﾙｸ 1.2~1.5N･m",
"取付け寸法 10.5mm"
],
"InspectionNo": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2~1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. ①にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"2. 1.完成品にPOST を挿入し④をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当て... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立⑤",
"WorkItems": [
"1. ①のｼｬﾌﾄに②･③･④を挿入し⑯･⑰で組付け"
],
"WorkPoints": [
"③は②を挿入後④を組付ける前に挿入",
"②はﾄﾞｸﾞとｽﾄｯﾊﾟｰの位置関係に注意して挿入すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立⑥",
"WorkItems": [
"1. ①に②を取付",
"2. 1.完成品に③を⑯･⑰･⑱で取付"
],
"WorkPoints": [
"ﾄﾞｸﾞの下側に通すこと",
"ﾎﾟｽﾄの穴にｾﾝｻの突起を挿し込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-089",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3.5㎜",
"ToolOther": "",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:3.5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立②",
"WorkItems": [
"1. ①に②を⑯･⑰で組付け",
"2. 1.完成品に⑱･⑲を仮止め"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1.完成品",
"仮止め:SD-A... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立③",
"WorkItems": [
"1. ①に②をﾍﾞﾙﾄを通して⑯･⑰で仮止め"
],
"WorkPoints": [
"4箇所全てを⑯厚肉ﾜｯｼｬｰでﾌﾟﾚｰﾄを挟み込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"仮止... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "θ軸駆動部組立④",
"WorkItems": [
"2. 1.完成品に②･③を⑯で取付"
],
"WorkPoints": [
"SD-A044762-010, 011で仮止めしていたﾎﾞﾙﾄを本締めすること",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ:234~267Hz",
"ﾄﾞｸﾞは原点ｾﾝｻｰに対し下記寸法を目安とする｡"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立④",
"WorkItems": [
"2. 1.完成品に②･③を⑯で取付"
],
"WorkPoints": [
"SD-A044762-010, 011で仮止めしていたﾎﾞﾙﾄを本締めすること",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ:234~267Hz",
"ﾄﾞｸﾞは原点ｾﾝｻｰに対し下記寸法を目安とする｡"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-0... | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "234~267Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3.5㎜",
"ToolOther": "",
"WorkName": "θ軸駆動部組立④",
"WorkItems": [
"2. 1.完成品に②･③を⑯で取付"
],
"WorkPoints": [
"SD-A044762-010, 011で仮止めしていたﾎﾞﾙﾄを本締めすること",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ:234~267Hz",
"ﾄﾞｸﾞは原点ｾﾝｻｰに対し下記寸法を目安とする｡"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:3.5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立①",
"WorkItems": [
"1. ①･②に③を組付け"
],
"WorkPoints": [
"この作業では同じものを2個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立②",
"WorkItems": [
"1. ①･②に③･④を⑯･⑰･⑱で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"L用",
"R... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立③",
"WorkItems": [
"1. ①に②を⑳・㉑・㉒で組付け",
"2. ③･④に⑤を⑲･⑰･⑱で組付け",
"3. 2.完成品に1.完成品・⑥を⑲・⑳・㉑・㉒で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTy... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立④",
"WorkItems": [
"1. ①に②･③を⑯･⑰で組付け",
"2. 1.完成品に④･⑤を⑱で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:12.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑤",
"WorkItems": [
"1. ①･②に③を④･⑯で組付け",
"2. 1.完成品に⑤･⑥を⑰で組付け"
],
"WorkPoints": [
"⑤を組付け後に⑥を組付け",
"この作業ではL･R用それぞれ1個作成",
"⑤を組付け後に⑥を組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑥",
"WorkItems": [
"1. ①･②に③･④を⑯･⑰で組付け",
"2. 1.完成品に⑤･⑥を⑯･⑱で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Wo... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑦",
"WorkItems": [
"1. ①･②に③･④･⑤を⑯で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"L用",
"R用"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑧",
"WorkItems": [
"2. ①･②に1.でｶｯﾄした配管を取付",
"1. ⑥を指定の長さでｶｯﾄ"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑨",
"WorkItems": [
"2. ③に④を圧入",
"1. ①に②を組付け",
"3. 2.完成品に⑤を⑯で組付け"
],
"WorkPoints": [
"この作業ではそれぞれ4個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:5.7㎜±0.1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑨",
"WorkItems": [
"2. ③に④を圧入",
"1. ①に②を組付け",
"3. 2.完成品に⑤を⑯で組付け"
],
"WorkPoints": [
"この作業ではそれぞれ4個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑨",
"WorkItems": [
"2. ③に④を圧入",
"1. ①に②を組付け",
"3. 2.完成品に⑤を⑯で組付け"
],
"WorkPoints": [
"この作業ではそれぞれ4個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:19.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑩",
"WorkItems": [
"2. 1.完成品に③を⑱で組付け",
"1. ①に②を組付け",
"3. 2.完成品に⑥を貼付け"
],
"WorkPoints": [
"この作業ではそれぞれ4個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:13.7㎜±0.1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑩",
"WorkItems": [
"2. 1.完成品に③を⑱で組付け",
"1. ①に②を組付け",
"3. 2.完成品に⑥を貼付け"
],
"WorkPoints": [
"この作業ではそれぞれ4個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑪",
"WorkItems": [
"2. 1.完成品に⑥を組付け",
"1. ①に②･③･④･⑤を⑯･⑰で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"Dﾋﾟﾝ押当て",
"4面共組... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑫",
"WorkItems": [
"1. ①に②･③を⑯で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"A-A断面図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑬",
"WorkItems": [
"1. ①に⑥･⑦の配管を接続しBOLT ･WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"上面図",
"⑥配管",
"⑥配管",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "昇降部組立⑭",
"WorkItems": [
"1. ①の原点位置でのﾌﾟﾚｰﾄ平面度確認"
],
"WorkPoints": [
"平面度 0.05mm以下"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-089",
"InspectionItems": [
"検査表①:ﾌﾟﾚｰﾄ平面度確認"
],
"WorkTypes": [
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.05㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部配線①",
"WorkItems": [
"1. ①にCABLE ･CABLE ･CABLE ･LABEL TERMINAL PROCESS を取付"
],
"WorkPoints": [
"合わせる",
"合わせる"
],
"Tolks": [
"KEYENCE PR-MB30N1の配線に取付",
"KEYENCE PR-MB30N1の配線に取付"
],
"InspectionNo": "W... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部配線②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-115",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"WWYJ-5300-115"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部配線③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-115",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"WWYJ-5300-115"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"1. ①に②を⑯･⑰で組付け",
"2. 1.完成品に③を組付け"
],
"WorkPoints": [
"この作業ではそれぞれ2個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. ②のｽﾋﾟｺﾝを調整",
"2. ①に2.完成品･③をに③を④･⑯･⑰で組付け"
],
"WorkPoints": [
"この作業ではL･R用を作成",
"ｽﾋﾟｺﾝ:全閉から2回転開く",
"この作業では8個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全閉から2回転開く",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立③",
"WorkItems": [
"1. ⑥を指定の長さにｶｯﾄ",
"2. ①･②に1.完成品を挿入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"150mm",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立④",
"WorkItems": [
"▲1. ①に②･③を⑯･⑰で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"裏側",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立⑤",
"WorkItems": [
"1. ①に②を⑯･⑰で組付け",
"2. 1.完成品に③を組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"1.完成... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP認識照明部取付",
"WorkItems": [
"1. ①にSPACER をSCREW で組付け",
"2. 定盤上で1.完成品に⑦をBOLT ・㉒で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"W... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ取付①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ取付②",
"WorkItems": [
"1. ①に②･③をBOLT ･WASHER で組付け",
"2. ①にSPACER をSCREW で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空部配線",
"WorkItems": [
"1. ①にCABLE ･CABLE を接続"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-115",
"InspectionItems": [
"検査表①:接続確認 (5)ICﾄﾚｲｽﾃｰｼﾞ部(逆流れｽﾃｰｼﾞ)"
],
"WorkTypes": [
"▲特殊作業",
"●クリ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ組立",
"WorkItems": [
"1. ①に⑥を貼付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"9㎜",
"63㎜",
"22㎜"
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾃｰｼﾞXY軸部へ払い出し",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "払出確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示の払出である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "SWITCH作成",
"WorkItems": [
"1. ①に②を取付"
],
"WorkPoints": [
"2ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "集中給油部組立",
"WorkItems": [
"1. ①に②③を取付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "給油ｼﾞｮｲﾝﾄ部組立",
"WorkItems": [
"1. ①に②を⑯⑰⑱で取付け",
"2. ②に③を取付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立",
"WorkItems": [
"2. ①に②を③で取付",
"■1. 型式確認､ｼﾘｱﾙ№記録"
],
"WorkPoints": [
"定盤に押し当てて､図の方向にて取付",
"ﾌﾟﾚｰﾄを下にして文字が読めるように取付",
"型式: PSLH303-00A"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-41",
"Insp... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-41",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立",
"WorkItems": [
"2. ①に②を③で取付",
"■1. 型式確認､ｼﾘｱﾙ№記録"
],
"WorkPoints": [
"定盤に押し当てて､図の方向にて取付",
"ﾌﾟﾚｰﾄを下にして文字が読めるように取付",
"型式: PSLH303-00A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-41",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ接続ﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"1. ①に⑥を貼付け",
"▲2. 1.完成品に②を④で貼付け",
"3. ①に③を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"▲特殊作業",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ接続ﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"1. ①に⑥を貼付け",
"▲2. 1.完成品に②を④で貼付け",
"3. ①に③を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"▲特殊作業",
"●クリー... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各4",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ接続ﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. ①に②③④をそれぞれ⑯⑰で取付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ接続ﾌﾞﾗｹｯﾄ組立③",
"WorkItems": [
"1. ①に②を③⑯で取付け",
"2. ①に④を⑰⑱で取付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ARM組立①PIN圧入",
"WorkItems": [
"1. ①に②を圧入"
],
"WorkPoints": [
"出代5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ARM組立②可動子用PIN",
"WorkItems": [
"1. ①に②を③④⑯で取付"
],
"WorkPoints": [
"Dｶｯﾄ部分を外側(ｾｯﾄﾋﾞｽ側)を向けて挿入"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:8.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ARM組立③ｽﾍﾟｰｻｰFT4",
"WorkItems": [
"1. ①に②③を⑯で取付",
"2. ①に④を取付",
"3. ③に④を取付"
],
"WorkPoints": [
"③の上に取付",
"⑯は出代4㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ARM組立④ｽﾄｯﾊﾟｰ",
"WorkItems": [
"1. ①に②③④を⑤で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ARM組立⑤給油",
"WorkItems": [
"1. ①に②を⑯⑰で取付",
"2. ①に③を⑰⑱で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ARM組立⑥可動子",
"WorkItems": [
"2. ①に②を⑯⑰で取付",
"■1. 可動子の型式確認､ｼﾘｱﾙ№記録"
],
"WorkPoints": [
"②可動子の黄丸の穴にﾋﾟﾝを挿入しﾎﾞﾙﾄを締結する事",
"ｹｰﾌﾞﾙを図の方向に向けて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "WWYJ-5300-41",
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-41",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ARM組立⑥可動子",
"WorkItems": [
"2. ①に②を⑯⑰で取付",
"■1. 可動子の型式確認､ｼﾘｱﾙ№記録"
],
"WorkPoints": [
"②可動子の黄丸の穴にﾋﾟﾝを挿入しﾎﾞﾙﾄを締結する事",
"ｹｰﾌﾞﾙを図の方向に向けて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-41",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.0N･m",
"WorkName": "ARM組立⑥可動子",
"WorkItems": [
"2. ①に②を⑯⑰で取付",
"■1. 可動子の型式確認､ｼﾘｱﾙ№記録"
],
"WorkPoints": [
"②可動子の黄丸の穴にﾋﾟﾝを挿入しﾎﾞﾙﾄを締結する事",
"ｹｰﾌﾞﾙを図の方向に向けて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.