input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"②仮付け後､金ﾆｽを塗布する",
"ｸﾞﾘｰｽﾆｯﾌﾟﾙの位置",
"･②の取付け位置に注意する･... | {
"QualityItem": "金ﾆｽ塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組込み①",
"WorkItems": [
"◆1. ①に②をBOLT で16箇所で固定する(重量物のためｸﾚｰﾝを使用すること)"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組込み①",
"WorkItems": [
"◆1. ①に②をBOLT で16箇所で固定する(重量物のためｸﾚｰﾝを使用すること)"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"◆1. MOTOR-BRACKET の下面及び左側面以外の外周りの加工面に金ﾆｽを塗装する",
"◆2. BEARING にｸﾞﾘｰｽをいれIﾏｰｸを合わせる",
"3. 2完成品にPLATE をBOLT で締結する"
],
"WorkPoints": [
"･BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞはﾏｰｸを合わせ､MOTOR-BRACKET に挿入する(正面合わせ､... | {
"QualityItem": "金ﾆｽ塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"◆1. MOTOR-BRACKET の下面及び左側面以外の外周りの加工面に金ﾆｽを塗装する",
"◆2. BEARING にｸﾞﾘｰｽをいれIﾏｰｸを合わせる",
"3. 2完成品にPLATE をBOLT で締結する"
],
"WorkPoints": [
"･BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞはﾏｰｸを合わせ､MOTOR-BRACKET に挿入する(正面合わせ､... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の30%~40%",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"3. 2完成品にPLATE をBOLT で締結する"
],
"WorkPoints": [
"挿入時方向に注意する",
"取付け後､隙間を確認(0.01㎜以上)",
"塗布禁止場所(ﾓｰﾀｰ取付け面､ﾌﾚｰﾑ取付け面)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰﾌﾞﾗｹｯﾄ組込み",
"WorkItems": [
"1. ①のﾎﾞｰﾙﾈｼﾞにSTOPPER を挿入する",
"2. 1完成品に②を挿入しBOLT で締結する"
],
"WorkPoints": [
"挿入時ﾋﾟﾝに当てながらﾎﾞｰﾙねじ部がｽﾑｰｽﾞに挿入できること(ﾋﾟﾝとの隙間:0.01㎜以下)",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "10N･m",
"WorkName": "H軸ﾎﾞｰﾙねじ芯出し",
"WorkItems": [
"2. 1完成品のﾎﾞｰﾙねじ取付け部の仮締め部分の本締め6箇所を行う"
],
"WorkPoints": [
"NUT のNUT方向注意",
"WASHER ｶﾗｰ2枚",
"NUT ﾅｯﾄﾄﾙｸ締付後付属品で固定",
"ﾋﾟｰｽ･ｾｯﾄﾋﾞｽ",
"･NUT ﾅｯﾄは挿入方向に注意･ﾄﾙｸ締結後､NUT 付属品で固定する",... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000㎜",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾙねじ芯振れ確認",
"WorkItems": [
"1. ①のﾎﾞｰﾙﾈｼﾞ先端の芯振れを確認する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-062",
"InspectionItems": [],
... | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "10μm以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000㎜",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾙねじｽﾗｽﾄｶﾞﾀ確認",
"WorkItems": [
"1. ①のﾎﾞｰﾙねじｽﾗｽﾄ方向のｶﾞﾀを確認する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-062",
"InspectionItems"... | {
"QualityItem": "ｽﾗｽﾄ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "ｶﾞﾀ5μm以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "2.5N･m以下",
"WorkName": "ﾎﾞｰﾙねじ回転ﾄﾙｸ測定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"･回転ﾄﾙｸ値:2.5N･m以下･下限付近と上限付近の最大値記入",
"検査表①:H軸ﾎﾞ... | {
"QualityItem": "回転ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "2.5N以下",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組付け",
"WorkItems": [
"■1. MOTOR の型式確認とｼﾘｱﾙ№を検査書に記入",
"2. ①のｺﾈｸﾀｰにLABEL TERMINAL PROCESS ﾏｰｷﾝｸﾞﾀｲ取付け",
"3. ①にCOUPLING を挿入し､2完成品をBOLT WASHER で締結する"
],
"WorkPoints": [
"P1･EM4210P(6P)･BM4210P(2P)･MM4210P(4P)",
"各... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組付け",
"WorkItems": [
"■1. MOTOR の型式確認とｼﾘｱﾙ№を検査書に記入",
"2. ①のｺﾈｸﾀｰにLABEL TERMINAL PROCESS ﾏｰｷﾝｸﾞﾀｲ取付け",
"3. ①にCOUPLING を挿入し､2完成品をBOLT WASHER で締結する"
],
"WorkPoints": [
"P1･EM4210P(6P)･BM4210P(2P)･MM4210P(4P)",
"各... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀｰ原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "H軸原点調整①",
"WorkItems": [
"2.①のｶｯﾌﾟﾘﾝｸﾞの下側ﾅｯﾄを締結する",
"1. ①のモーターコネクターに治具㉖㉗を接続し、駆動部を上下させフレーム後側から㉘原点出しピン（φ6-120㎜）を挿入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具",
"Size": "",
"ToolOther": "FM-3229",
"WorkName": "H軸原点調整①",
"WorkItems": [
"2.①のｶｯﾌﾟﾘﾝｸﾞの下側ﾅｯﾄを締結する",
"1. ①のモーターコネクターに治具㉖㉗を接続し、駆動部を上下させフレーム後側から㉘原点出しピン（φ6-120㎜）を挿入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾃｰﾌﾞﾙX軸用ﾋﾟﾝ",
"Size": "φ6",
"ToolOther": "FM-3467",
"WorkName": "H軸原点調整①",
"WorkItems": [
"2.①のｶｯﾌﾟﾘﾝｸﾞの下側ﾅｯﾄを締結する",
"1. ①のモーターコネクターに治具㉖㉗を接続し、駆動部を上下させフレーム後側から㉘原点出しピン（φ6-120㎜）を挿入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3467",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "19㎜",
"ToolOther": "29.4N･m",
"WorkName": "H軸原点調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 29.4N･m"
],
"InspectionNo": "WWYJ-5300-062",
"InspectionItems": [
"検査表①:ｶｯﾌﾟﾘﾝｸﾞ締結"
],
"WorkTypes": [
"■安全作業"
],
"Words": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "29.4N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀｰ原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "H軸原点調整②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 63.7N･m"
],
"InspectionNo": "WWYJ-5300-062",
"InspectionItems": [
"検査表①:ｶｯﾌﾟﾘﾝｸﾞ締結"
],
"WorkTypes": [
"■安全作業"
],
"Words": [... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具",
"Size": "",
"ToolOther": "FM-3229",
"WorkName": "H軸原点調整②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 63.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾓｰﾀｰと駆動部が原点にいる事",
"検査表①:ｶｯﾌﾟﾘ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾃｰﾌﾞﾙX軸用ﾋﾟﾝ",
"Size": "φ6",
"ToolOther": "FM-3467",
"WorkName": "H軸原点調整②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 63.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾓｰﾀｰと駆動部が原点にいる事",
"検査表①... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3467",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "29㎜",
"ToolOther": "63.7N･m",
"WorkName": "H軸原点調整②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 63.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾓｰﾀｰと駆動部が原点にいる事",
"検査表①:ｶｯﾌﾟ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "63.7N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前部ｽｹｰﾙ部組込み",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-065",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"WWYJ-5300-065"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-065",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100㎜",
"ToolOther": "",
"WorkName": "駆動軸ﾌﾞﾗｹｯﾄにﾌﾟﾚｰﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-062",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:H軸ﾌﾞﾗｹｯﾄ平行確認",
"平行度測定位... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "L点で0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "駆動部ﾌﾚｰﾑにFT4取付け",
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立①",
"WorkItems": [
"1. BRACKET にLABEL ⑯を貼付けする"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1. ①にMANIFOLD MANIFOLD をBOLT WASHER で締結する",
"2. ①にJOINT SPACER をBOLT W... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. ①にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P1:⑥⑦⑧の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. ①にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P2:⑥⑦⑧の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. ①にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P1:⑥⑦⑧の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. ①にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P2:⑥⑦⑧の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. ①にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P1ﾘﾚｰ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. ①にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P2ﾘﾚｰ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"3. ①にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING... | {
"QualityItem": "P1:⑥の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"3. ①にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING... | {
"QualityItem": "P1:⑥の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"3. ①にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING... | {
"QualityItem": "P1:⑥の設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"3. ①にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING... | {
"QualityItem": "P2:⑥の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"3. ①にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING... | {
"QualityItem": "P2:⑥の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"3. ①にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING... | {
"QualityItem": "P2:⑥の設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立⑤",
"WorkItems": [
"1. ①にCABLE CABLE CABLE をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"1B10640",
"1B10630",
"1R30620",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)",
"1B10E40",
"1B10E30",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立⑥",
"WorkItems": [
"1. ①にP1はCABLE (P2はCABLE )をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"1B10620",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)",
"1B10E20"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "背面部組立⑦",
"WorkItems": [
"1. TUBE TUBE を指定の長さにｶｯﾄする",
"2. ①にTUBE TUBE を取付ける"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立⑧(OPL3/R3,L4/R4)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立1(F側)",
"WorkItems": [
"2. 1完成品をPLATE にBOLT で取付ける",
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"治具との隙間:0.05㎜が入ら無い事",
"表面",
"ﾌﾟﾚｰﾄ裏側",
"付属のﾅｯﾄは廃棄する"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ﾌﾟﾚｰﾄ組立1(F側)",
"WorkItems": [
"2. 1完成品をPLATE にBOLT で取付ける",
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"治具との隙間:0.05㎜が入ら無い事",
"表面",
"ﾌﾟﾚｰﾄ裏側",
"付属のﾅｯﾄは廃棄する"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立1(F側)",
"WorkItems": [
"2. 1完成品をPLATE にBOLT で取付ける",
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"治具との隙間:0.05㎜が入ら無い事",
"表面",
"ﾌﾟﾚｰﾄ裏側",
"付属のﾅｯﾄは廃棄する"
],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立1(F側)",
"WorkItems": [
"2. 1完成品をPLATE にBOLT で取付ける",
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"治具との隙間:0.05㎜が入ら無い事",
"表面",
"ﾌﾟﾚｰﾄ裏側",
"付属のﾅｯﾄは廃棄する"
],
"T... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立2(F側)",
"WorkItems": [
"1. ①にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"①に治具をｾｯﾄする",
"BLOCK を治具に挿入し取付ける",
"取付け方向に注意する事(面取り側)",
"表面",
"裏面"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ﾌﾟﾚｰﾄ組立2(F側)",
"WorkItems": [
"1. ①にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"①に治具をｾｯﾄする",
"BLOCK を治具に挿入し取付ける",
"取付け方向に注意する事(面取り側)",
"表面",
"裏面"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立3(F側)",
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具との隙間:0.05㎜が入ら無い事",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固定の事",
"ﾌﾞﾗｹｯﾄの取付方向に注意する... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ﾌﾟﾚｰﾄ組立3(F側)",
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具との隙間:0.05㎜が入ら無い事",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固定の事",
"ﾌﾞﾗｹｯﾄの取付方向に注意する事"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立3(F側)",
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具との隙間:0.05㎜が入ら無い事",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固定の事",
"ﾌﾞﾗｹｯﾄの取付方向に注意する事"
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "90cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立4(F側)",
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板下受け組立台",
"Size": "",
"ToolOther": "FM-3433",
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3433",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜の... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜を挟んで取付",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜の... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が入る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜の... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜の... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜が入る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ｿｹｯﾄ5.5㎜",
"ToolOther": "90cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "平面度測定ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5001",
"WorkName": "ﾌﾟﾚｰﾄ測定(F側)",
"WorkItems": [
"1. ①を治具に取付ける",
"2. ①の平面度を測定する",
"1. ①を治具に取付ける",
"2. ①の平面度を測定する"
],
"WorkPoints": [
"一番高い所を0(基準)とする",
"測定位置❶～⓬に測定シャフトを置きその上を測定する（皿ネジ近傍の内より側）",
"測定ｼｬﾌﾄ",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5001",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ測定(F側)",
"WorkItems": [
"1. ①を治具に取付ける",
"2. ①の平面度を測定する"
],
"WorkPoints": [
"一番高い所を0(基準)とする",
"測定位置❶～⓬に測定シャフトを置きその上を測定する（皿ネジ近傍の内より側）",
"測定ｼｬﾌﾄ"
],
"Tolks": [],
"InspectionNo": "WETE-G... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "平面度-0.20㎜~+0.10㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(F側)",
"WorkItems": [
"1. ①にWASHER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立1(R側)",
"WorkItems": [
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける",
"2. 1完成品をPLATE にBOLT で取付ける"
],
"WorkPoints": [
"表面",
"付属のﾅｯﾄは廃棄する",
"治具との隙間:0.05㎜が入ら無い事"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ﾌﾟﾚｰﾄ組立1(R側)",
"WorkItems": [
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける",
"2. 1完成品をPLATE にBOLT で取付ける"
],
"WorkPoints": [
"表面",
"付属のﾅｯﾄは廃棄する",
"治具との隙間:0.05㎜が入ら無い事"
],
"Tolks": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立1(R側)",
"WorkItems": [
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける",
"2. 1完成品をPLATE にBOLT で取付ける"
],
"WorkPoints": [
"表面",
"付属のﾅｯﾄは廃棄する",
"治具との隙間:0.05㎜が入ら無い事"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立1(R側)",
"WorkItems": [
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける",
"2. 1完成品をPLATE にBOLT で取付ける"
],
"WorkPoints": [
"表面",
"付属のﾅｯﾄは廃棄する",
"治具との隙間:0.05㎜が入ら無い事"
],
"Tolks": [
"締... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立2(R側)",
"WorkItems": [
"1. ①にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"①に治具をｾｯﾄする",
"BLOCK を治具に挿入し取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ﾌﾟﾚｰﾄ組立2(R側)",
"WorkItems": [
"1. ①にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"①に治具をｾｯﾄする",
"BLOCK を治具に挿入し取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立3(R側)",
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具をｾｯﾄする",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固定の事",
"治具との隙間:0.05㎜が入ら無い事",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ﾌﾟﾚｰﾄ組立3(R側)",
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具をｾｯﾄする",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固定の事",
"治具との隙間:0.05㎜が入ら無い事",
"B... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立3(R側)",
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具をｾｯﾄする",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固定の事",
"治具との隙間:0.05㎜が入ら無い事",
"BRACK... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "90cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"WorkItems": [
"1. ①に⑱を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板下受け組立台",
"Size": "",
"ToolOther": "FM-3433",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3433",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜の... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜を挟んで取付",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜の... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が入る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜の... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜の... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜が入る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ｿｹｯﾄ5.5㎜",
"ToolOther": "90cN･m",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",
"FM-3433",
"ﾌﾟ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "平面度測定ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5001",
"WorkName": "ﾌﾟﾚｰﾄ測定(R側)",
"WorkItems": [
"1. ①を治具に取付ける",
"2. ①の平面度を測定する"
],
"WorkPoints": [
"平面度:-0.20㎜~+0.10㎜",
"一番高い所を0(基準)とする",
"測定位置❶～⓬に測定シャフトを置きその上を測定する（皿ネジ近傍の内より側）",
"測定ｼｬﾌﾄ"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5001",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ測定(R側)",
"WorkItems": [
"1. ①を治具に取付ける",
"2. ①の平面度を測定する"
],
"WorkPoints": [
"平面度:-0.20㎜~+0.10㎜",
"測定位置❶～⓬に測定シャフトを置きその上を測定する（皿ネジ近傍の内より側）"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C29",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "平面度-0.20㎜~+0.10㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C29",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(R側)",
"WorkItems": [
"1. ①に②を⑯⑰で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "製造手配銘板貼付け",
"WorkItems": [
"2. ①と②に③を貼付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄの裏面(部品取付面)に貼付ける事",
"REAR",
"FRONT"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨﾙﾀｰｷｯﾄ組立",
"WorkItems": [
"1. SHEET にFILTER をRUBBER-CUSHION で取付ける"
],
"WorkPoints": [
"ｼｰﾄのR処理されている方に取付ける事",
"ｼｰﾄにひび割れがないか確認する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM型式確認",
"WorkItems": [
"■1. PCB-COM の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙ"
],
"Tolks": [],
"InspectionNo": "2LC-JG-21011",
"InspectionItems": [
"検査表PCB-COM :1.安全部品ﾁｪｯｸ"
],
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-21011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM型式確認",
"WorkItems": [
"■1. PCB-COM の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙ"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [
"検査表②:1.構成ﾁｪｯｸ"
],
"WorkTyp... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~JP8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定すべてOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-21011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~JP8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定すべてOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~JP8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定すべてOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り設定されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "30cN･m",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ取付け①",
"WorkItems": [
"1. ①にSPACER をSCREW WASHER で取付ける",
"2. 1完成品に②を載せる"
],
"WorkPoints": [
"ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀのｶﾒﾗI/Fﾎﾞｰﾄﾞｺﾈｸﾀ部に基板を入れてPCI-Eｺﾈｸﾀの勘合を行う",
"勘合の際､各基板に過度のｽﾄﾚｽをかけない様注意する事",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ取付け①",
"WorkItems": [
"1. ①にSPACER をSCREW WASHER で取付ける",
"2. 1完成品に②を載せる"
],
"WorkPoints": [
"ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀのｶﾒﾗI/Fﾎﾞｰﾄﾞｺﾈｸﾀ部に基板を入れてPCI-Eｺﾈｸﾀの勘合を行う",
"勘合の際､各基板に過度のｽﾄﾚｽをかけない様注意する事",
"SPACER の線を下にして... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-21011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ4.0㎜",
"ToolOther": "10cN･m",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "35cN･m",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ取付け②",
"WorkItems": [
"1. ①にSCREW を取付ける",
"2.1完成品をSCREW WASHER で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 35cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "35cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝﾀｰﾚｰﾙ前組立て",
"WorkItems": [
"1. INSULATOR を点線の位置で折る",
"2. RAIL の指定箇所に､1.完成品の上側を引っ掛け､左基準で穴位置を合わせ押し込む"
],
"WorkPoints": [
"不要の為廃棄",
"1.完成品",
"ｶﾁｯというまで確実に取付ける事",
"ｲﾝｼｭﾚｰﾀｰの取付け位置･方向に注意する事"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱﾚｰﾙ前組立て",
"WorkItems": [
"1. INSULATOR を点線の位置で折る",
"2. RAIL の指定箇所に､1.完成品の下側を引っ掛け､左基準で穴位置を合わせ押し込む"
],
"WorkPoints": [
"不要の為廃棄",
"1.完成品",
"ｶﾁｯというまで確実に取付ける事",
"ｲﾝｼｭﾚｰﾀｰの取付け位置･方向に注意する事"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾙ取付け①",
"WorkItems": [
"1. BRACKET の指定箇所にRAIL をｾｯﾄし､SCREW で仮締めする(2箇所)",
"2. 1.完成品のRAIL にPLATE を面取り部を前面にして切断面から挿入する(上下2箇所)"
],
"WorkPoints": [
"上側",
"下側",
"ﾀﾞﾎﾞに当てつける事",
"ﾀﾞﾎﾞに当てつける事",
"前面",
"ﾚｰﾙの取... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾙ取付け②",
"WorkItems": [
"1. ⑤の指定箇所にRAIL ③④をｾｯﾄし､SCREW で仮締めする"
],
"WorkPoints": [
"ﾚｰﾙの取付方向に注意する事",
"ﾀﾞﾎﾞに当てつける事",
"上側",
"中側",
"下側",
"ﾀﾞﾎﾞに当てつける事",
"ﾀﾞﾎﾞに当てつける事",
"ｲﾝｼｭﾚｰﾀｰが下向きに取付ける事",
"SD... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付け",
"WorkItems": [
"1. ②のﾚｰﾙ取付穴の左から3番目にGUIDE をｾｯﾄし､下から押し込み取付ける(2箇所)",
"2. ②のﾚｰﾙ取付穴の左から3番目にGUIDE をｾｯﾄし､上から押し込み取付ける(2箇所)"
],
"WorkPoints": [
"左から3番目",
"下側",
"左から3番目",
"上側"
],
"Tolks": [],
"Inspe... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM確認",
"WorkItems": [
"1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表PCB-COM :1.安全部品受入"
],
"WorkTypes": [
"■安全作業"
],
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM仮取付け",
"WorkItems": [
"1. ①の裏面を手前にする",
"2. ①のﾚｰﾙ穴と､②の穴位置を合せ､SCREW で仮締めする(6箇所)"
],
"WorkPoints": [
"ｲﾝｼｭﾚｰﾀｰがある事を確認する",
"ﾚｰﾙの右端から4つ目に穴位置を合せる事",
"基板調整の為､仮締めにする事(6箇所)",
"裏面",
"ｲﾝｼｭﾚｰﾀｰが下側にある事を確認",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部確認",
"WorkItems": [
"■1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNo.を検査表に記入する",
"■2. 指定箇所に認証ﾏｰｸが記載されている事を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表POWER-SUPPLY :1.安全部品受入",... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部確認",
"WorkItems": [
"■1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNo.を検査表に記入する",
"■2. 指定箇所に認証ﾏｰｸが記載されている事を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表POWER-SUPPLY :1.安全部品受入",... | {
"QualityItem": "認証ﾏｰｸ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "認証ﾏｰｸが記載されている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.