input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整1",
"WorkItems": [
"1. ①を㉖に接続する",
"2. ㉖の背面にある電源をONにする",
"3. 画面右上のPower ONﾎﾞﾀﾝと〇印のﾎﾞﾀﾝを同時に押す"
],
"WorkPoints": [
"治具",
"ﾓｰﾀｰ",
"ｾﾝｻ接続の線はDOGが動くので当たらないように止めておく",
"右上のPower ONが黄色にならないと検査... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整2",
"WorkItems": [
"1. ﾌﾟﾛｾｽﾁｬﾝﾊﾞｰ調整/検査のﾎﾞﾀﾝを押す",
"2. センサ確認画面がでるので クランプ昇降部のセンサが反応するか㉗で遮光し確認する",
"3. 左下のMenuﾀﾌﾞを押す",
"4. 下にﾀﾌﾞが出てくるので､左から3番目のMoterを押す"
],
"WorkPoints": [],
"Tolks": [],
"Inspe... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整3",
"WorkItems": [
"2. 移動量を 41.3 に数値を設定する",
"1. 〇印の部分が有効になっていることを確認する",
"2. 移動量を 41.3 に数値を設定する"
],
"WorkPoints": [
"無効になってる場合はﾎﾞﾀﾝを押して有効に切り替える"
],
"Tolks": [],
"InspectionNo": "",
"Insp... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整4",
"WorkItems": [
"1. 原点のｼｬﾌﾄの高さを測る",
"3. JOG DownもしくはMOVEを押し､原点をずらしてから再度Originを押し原点復帰を行い､1の作業に戻る"
],
"WorkPoints": [
"高さ75.3㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
"どちらかでずらす",
"原点復帰",
"※高... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "75.3±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整4",
"WorkItems": [
"1. 原点のｼｬﾌﾄの高さを測る",
"3. JOG DownもしくはMOVEを押し､原点をずらしてから再度Originを押し原点復帰を行い､1の作業に戻る"
],
"WorkPoints": [
"高さ75.3㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
"どちらかでずらす",
"原点復帰",
"※高さが... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整5",
"WorkItems": [
"2. 原点のｼｬﾌﾄの高さを測る",
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合は､PH166(下降)の位置を動かして調整を行う"
],
"WorkPoints": [
"高さ34.0㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "34.0±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整5",
"WorkItems": [
"2. 原点のｼｬﾌﾄの高さを測る",
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合は､PH166(下降)の位置を動かして調整を行う",
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾈｼﾞ取付",
"WorkItems": [
"1. ①にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立(1/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "-",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立(2/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WDPY-F013-008"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り貼付してある事",
"Method": "目視",
"RecordMethod": "WDPY-F013-008",
"Other": "ﾆｯﾊﾟｰ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入治具",
"Size": "3㎜",
"ToolOther": "FM-2072",
"WorkName": "ﾍﾞｰｽ組立(3/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.①に③(4ヶ)を圧入する",
"2.1完成品に②(12ヶ)を圧入する"
]
} | {
"QualityItem": "ﾋﾟﾝ圧入",
"ToolManageNo": "FM-2072",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:3㎜",
"Method": "ﾋﾟﾝ圧入治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入台",
"Size": "",
"ToolOther": "FM-3218",
"WorkName": "ﾍﾞｰｽ組立(3/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.①に③(4ヶ)を圧入する",
"2.1完成品に②(12ヶ)を圧入する",
"1.①に③... | {
"QualityItem": "ﾍﾞｰｽ方向",
"ToolManageNo": "FM-3218",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り装着する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立(3/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.①に③(4ヶ)を圧入する",
"ﾋﾟﾝ出代:3mm",
"㉘ピン圧入治具FM-2072",
"... | {
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:3㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ(Φ5､2)",
"Size": "",
"ToolOther": "FM-5622",
"WorkName": "ﾍﾞｰｽ組立(3/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.①に③(4ヶ)を圧入する",
"ﾋﾟﾝ出代:3mm",
"㉘ピン圧入... | {
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "FM-5622",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:2㎜",
"Method": "ﾋﾟﾝ圧入ｼﾞｸﾞ(Φ5、2)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-2250",
"WorkName": "ﾍﾞｰｽ組立(4/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"上側の列4ヶ所に挿入の事｡ (下側の列4ヶ所は8ﾉｽﾞﾙ用)",
"2.FM-22... | {
"QualityItem": "圧入深さ",
"ToolManageNo": "FM-2250",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り圧入してある事",
"Method": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立(4/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"上側の列4ヶ所に挿入の事｡ (下側の列4ヶ所は8ﾉｽﾞﾙ用)",
"2.FM-2250の穴(4ヶ所)にPIN を挿入し､圧入... | {
"QualityItem": "ﾋﾟﾝ方向",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾃｰﾊﾟ側を上にして圧入",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊﾞﾈｶﾞｲﾄﾞ､Dﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-5995(1/2)FM-5995(2/2)",
"WorkName": "ﾍﾞｰｽ組立(5/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業",
"◆1.②(2ヶ)にｸ... | {
"QualityItem": "ﾋﾟﾝ圧入",
"ToolManageNo": "FM-5995(1/2)FM-5995(2/2)",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:30.5㎜",
"Method": "ﾊﾞﾈｶﾞｲﾄﾞ、Dﾋﾟﾝ圧入治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "150㎜",
"WorkName": "ﾍﾞｰｽ組立(5/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業",
"◆1.②(2ヶ)にｸﾞﾘｰｽを塗布し､①に圧入する",
"･ﾋﾟﾝ外周ｸﾞﾘ... | {
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:30.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立(5/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業",
"◆1.②(2ヶ)にｸﾞﾘｰｽを塗布し､①に圧入する",
"･ﾋﾟﾝ外周ｸﾞﾘｰｽを塗布(米... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊﾞﾈｶﾞｲﾄﾞ､Dﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-5995(1/2)",
"WorkName": "ﾍﾞｰｽ組立(6/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"時計周り180度 回す",
"◆作業者安全作業",
"1.... | {
"QualityItem": "ﾋﾟﾝ圧入",
"ToolManageNo": "FM-5995(1/2)",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "治具を使用して圧入する事",
"Method": "ﾊﾞﾈｶﾞｲﾄﾞ、Dﾋﾟﾝ圧入治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入治具",
"Size": "",
"ToolOther": "FM-3271",
"WorkName": "ﾍﾞｰｽ組立(6/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"時計周り180度 回す",
"◆作業者安全作業",
"1.㉖の上押さえカバーを ... | {
"QualityItem": "ﾋﾟﾝ圧入",
"ToolManageNo": "FM-3271",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "治具を使用して圧入する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立(6/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"時計周り180度 回す",
"◆作業者安全作業",
"1.㉖の上押さえカバーを ㉚で外す",
"しっかり... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立(7/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "剥がれ無き事米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "接着剤ｽｰﾊﾟｰX(AX-039)",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾍﾞｰｽ組立(8/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業",
"◆作業者安全作業"
],
"Words": [
"◆1.①に②③を⑯(4ヶ)で取付ける... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立(8/8)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆1.①に②③を⑯(4ヶ)で取付ける",
"◆作業者安全作業",
"締付けﾄﾙｸ: 95cN･m",
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ(P002)面処理",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.SHUTTER の表面と裏面に､軽く油砥石をかける",
"表面･裏面のｴｯｼﾞ部分にﾊﾞﾘ無き事",
"... | {
"QualityItem": "-",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ(P006)・ﾌﾞﾛｯｸ(P004)面処理",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "-",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀ取付(3/5)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀ取付(4/5)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆1.⑤と①のﾋﾟﾝ(N010)外周部に､ｸﾞﾘｰｽを塗布する",
"◆作業者安全作業",
"各部品に米粒大を塗布... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布各米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀ取付(5/5)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀ取付(5/5)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.①にBLOCK BLOCK を､BOLT で取付ける",
"BLOCK ",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽｱｯﾌﾟ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽﾍﾟｰｻ取付、動作確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.①にGUARD をSPACER BOLT (各2ヶ)で取付ける",
"GUARD... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬ確認治具",
"Size": "",
"ToolOther": "FM-2411",
"WorkName": "ｽﾍﾟｰｻ取付、動作確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WDPY-F013-008",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.①にGUARD をSPACER BOLT (各2ヶ)で取付ける... | {
"QualityItem": "着脱確認",
"ToolManageNo": "FM-2411",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｽﾑｰｽﾞに着脱可能な事",
"Method": "ﾉｽﾞﾙﾁｪﾝｼﾞｬ確認治具",
"RecordMethod": "WDPY-F013-008",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "4N･m",
"WorkName": "ｽﾍﾟｰｻ取付、動作確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WDPY-F013-008",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"2.ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認を実施する",
"検査表①:ﾉ... | {
"QualityItem": "ｼｬｯﾀｰ動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正管理台張",
"StdVal": "4N以下",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "WDPY-F013-008",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "貼付位置",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り貼付してある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付2(製造手配銘板)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1.製造手配銘板を貼付"
]
} | {
"QualityItem": "貼付位置",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り貼付してある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "ﾁｪﾝｼﾞｬｰ動作",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示書通り動作する事",
"Method": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WDPY-F013-008"
]
} | {
"QualityItem": "ﾁｪﾝｼﾞｬｰ動作",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示書通り動作する事",
"Method": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"RecordMethod": "WDPY-F013-008",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "X軸真直確認治具",
"Size": "",
"ToolOther": "FM-2209",
"WorkName": "左側ｶﾞｲﾄﾞ組立1/3",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
"FM-2209",
"BRACKET の幅を㉖で広げる"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2209",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立1/3",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
"FM-2209",
"BRACKET の幅を㉖で広げる"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. ①にTAPE を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事",
"端面40㎜から貼付け",
"表面の端面 6mmから貼付"
],
"Tolks... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. ①にTAPE を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事",
"端面40㎜から貼付け",
"表面の端面 6mmから貼付"
],
"Tolks":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. ①にTAPE を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事",
"端面40㎜から貼付け",
"表面の端面 6mmから貼付"
],
"Tolks": [],
"I... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. ①にTAPE を貼付ける",
"1. ①にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. ①にTAPE を貼付ける",
"1. ①にBRACKET をB... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立3/3",
"WorkItems": [
"1. GUIDE へTAPE を貼付ける",
"2. 1.完成品を③へBOLT WASHER で取付ける"
],
"WorkPoints": [
"右側ｴｯｼﾞ部から貼付けて気泡が入らない様貼付ける事",
"GUIDE の取付位置は長穴ｾﾝﾀｰで取付ける取付の際中央位置を仮固定し両ｻｲﾄﾞで確認し位置決めする"
],
"Tolks":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立3/3",
"WorkItems": [
"1. GUIDE へTAPE を貼付ける",
"2. 1.完成品を③へBOLT WASHER で取付ける"
],
"WorkPoints": [
"右側ｴｯｼﾞ部から貼付けて気泡が入らない様貼付ける事",
"GUIDE の取付位置は長穴ｾﾝﾀｰで取付ける取付の際中央位置を仮固定し両ｻｲﾄﾞで確認し位置決めする"
],
"Tolks": [],
... | {
"QualityItem": "貼付け確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側ｶﾞｲﾄﾞ組立1/2",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"FM-2209"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 9.8N･m",
"BOLT 締付ﾄﾙｸ 10.9N･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "10.9N･m",
"WorkName": "右側ｶﾞｲﾄﾞ組立1/2",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"FM-2209"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 9.8N･m",
"BOLT 締付ﾄﾙｸ 10.9N･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右側ｶﾞｲﾄﾞ組立2/2",
"WorkItems": [
"1. ①にCOVER を取付ける",
"2. 1.完成品の背面にTAPE を貼付ける",
"1. ①にCOVER を取付ける",
"2. 1.完成品の背面にTAPE を貼付ける"
],
"WorkPoints": [
"端面40㎜から取付ける",
"①とTAPE の端面合わせ",
"1㎜",
"端面40㎜から取付ける"... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. PLATE にPLATE をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"塗装面無しをこち... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀｰ&ｼﾞｮｲﾝﾄ部組立1/2",
"WorkItems": [
"1. BRACKET にJOINT を挿入しJOINT の付属ﾅｯﾄで固定する"
],
"WorkPoints": [
"JOINT の付属品"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "ｺﾈｸﾀｰ&ｼﾞｮｲﾝﾄ部組立2/2",
"WorkItems": [
"1. ①にCONNECTOR CONNECTOR をBOLT WASHER で取付ける"
],
"WorkPoints": [
"CONNECTOR を左､CONNECTOR を右に取付｡CONNECTOR とCONNECTOR は大きさが違う為､取付位置を間違わ無い事CONNECTOR CONNECTOR の取付方向も内側の山の部分が違う為... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. 1.完成品にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾋﾟﾝ出代:4㎜",
"ﾈｼﾞ穴ﾋﾟｯﾁを参照にD-pinを圧入"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [
"4㎜"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. 1.完成品にBRACKET をBOLT WASHER で取付ける",
"3. 2.完成品にBOLT WASHER を挿入し､STOPPER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"4㎜",
"ﾋﾟﾝ出代:4㎜",
"ﾈｼﾞ穴ﾋﾟｯﾁを参照にD-pinを... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品",
"WorkItems": [
"1. PLATE ~⑥WASHER BOLT を3工程に払い出す",
"2. ⑦を1工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "部品が揃っている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ組立",
"WorkItems": [],
"WorkPoints": [
"収縮ﾁｭｰﾌﾞ品番:SMTFZ-2-5P"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5mBOX",
"ToolOther": "60cN･m",
"WorkName": "TERMINAL組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀｰﾐﾅﾙ取付確認時ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5198",
"WorkName": "TERMINAL組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5198",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部ｹｰﾌﾞﾙ接続",
"WorkItems": [
"2. CABLE のP3ｺﾈｸﾀに､POWER-SUPPLY のP3ｺﾈｸﾀを接続する",
"3. 青ﾏｰｷﾝｸﾞする(1箇所)",
"■1. POWER-SUPPLY の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無､認証ﾏｰｸを確認し検査表に記入する",
"4. 配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯというまで確実に接続す... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-200052LC-JG-15021",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部ｹｰﾌﾞﾙ接続",
"WorkItems": [
"2. CABLE のP3ｺﾈｸﾀに､POWER-SUPPLY のP3ｺﾈｸﾀを接続する",
"3. 青ﾏｰｷﾝｸﾞする(1箇所)",
"■1. POWER-SUPPLY の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無､認証ﾏｰｸを確認し検査表に記入する",
"4. 配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯというまで確実に接続す... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-200052LC-JG-15021",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "電源部ｹｰﾌﾞﾙ接続",
"WorkItems": [
"2. CABLE のP3ｺﾈｸﾀに､POWER-SUPPLY のP3ｺﾈｸﾀを接続する",
"3. 青ﾏｰｷﾝｸﾞする(1箇所)",
"■1. POWER-SUPPLY の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無､認証ﾏｰｸを確認し検査表に記入する",
"4. 配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯというま... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀﾎﾞｰﾄﾞ確認",
"WorkItems": [
"■1. PCB-COM の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する"
],
"WorkPoints": [
"添付検査書:2LC-JG-20003"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-200042LC-JG-20005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀﾎﾞｰﾄﾞ確認",
"WorkItems": [
"■1. PCB-COM の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する"
],
"WorkPoints": [
"添付検査書:2LC-JG-20003"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-200042LC-JG-20005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定全てOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
"参... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-200042LC-JG-20005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定全てOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
"参... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-200042LC-JG-20005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "30cN･m",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け1",
"WorkItems": [
"1. ①にSPACER をSCREW WASHER で取付ける",
"2. 1完成品に②を載せる"
],
"WorkPoints": [
"ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀのｶﾒﾗI/Fﾎﾞｰﾄﾞｺﾈｸﾀ部に基板を入れてPCI-Eｺﾈｸﾀの勘合を行う",
"勘合の際､各基板に過度のｽﾄﾚｽをかけない様注意する事",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け1",
"WorkItems": [
"1. ①にSPACER をSCREW WASHER で取付ける",
"2. 1完成品に②を載せる"
],
"WorkPoints": [
"ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀのｶﾒﾗI/Fﾎﾞｰﾄﾞｺﾈｸﾀ部に基板を入れてPCI-Eｺﾈｸﾀの勘合を行う",
"勘合の際､各基板に過度のｽﾄﾚｽをかけない様注意する事",
"SPACER の線を下にし... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20004",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ4.0㎜",
"ToolOther": "10cN･m",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. ①にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m",
"締付ﾄﾙｸ 35cN･m"
],
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "35cN･m",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. ①にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m",
"締付ﾄﾙｸ 35cN･m"
],
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "35cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. ①にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける",
"3. 2完成品にLABEL を貼付ける",
"4. CPUﾎﾞｰﾄﾞのｼﾘｱﾙNo.を確認し､記録する"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001",
"ﾊﾟﾈﾙのｼﾙｸ印刷ﾗｲﾝに合わせて貼付ける"
]... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20004",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. ①にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける",
"3. 2完成品にLABEL を貼付ける",
"4. CPUﾎﾞｰﾄﾞのｼﾘｱﾙNo.を確認し､記録する"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001",
"ﾊﾟﾈﾙのｼﾙｸ印刷ﾗｲﾝに合わせて貼付ける"
]... | {
"QualityItem": "貼付け確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20004",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. ①にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける",
"3. 2完成品にLABEL を貼付ける",
"4. CPUﾎﾞｰﾄﾞのｼﾘｱﾙNo.を確認し､記録する"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001",
"ﾊﾟﾈﾙのｼﾙｸ印刷ﾗｲﾝに合わせて貼付ける"
]... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-15021",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝﾀｰﾚｰﾙ前組立",
"WorkItems": [
"1. RAIL の指定箇所に､INSULATOR の上を引っ掛け､左基準で穴位置を合わせ押し込む"
],
"WorkPoints": [
"INSULATOR の取付位置･方向に注意する事(写真参照)",
"ｶﾁｯというまで確実に取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱﾚｰﾙ前組立",
"WorkItems": [
"1. RAIL の指定箇所に､INSULATOR の上を引っ掛け､左基準で穴位置を合わせ押し込む"
],
"WorkPoints": [
"INSULATOR の取付位置･方向に注意する事(写真参照)",
"ｶﾁｯというまで確実に取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾙ取付1",
"WorkItems": [
"1. COVER の指定箇所にRAIL をｾｯﾄし､SCREW で仮締めする(2箇所)",
"2. 1.の完成品のRAIL にPLATE を面取り部を前面にして切断面から挿入する"
],
"WorkPoints": [
"指定箇所は写真参照 ･RAIL の取付方向に注意する事 ･COVER のﾀﾞﾎﾞにあてつける事",
"SD-A026382-019で本締結"
],
"T... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾙ取付2",
"WorkItems": [
"1. ⑤の指定箇所にRAIL をｾｯﾄし､SCREW で仮締めする",
"2. ⑤の指定箇所に③をｾｯﾄし､SCREW で仮締めする",
"3. ⑤の指定箇所に④をｾｯﾄし､SCREW で仮締めする"
],
"WorkPoints": [
"･指定箇所は写真参照 ･RAIL の取付方向に注意する ･ｶﾊﾞｰのﾀﾞﾎﾞにあてつける事",
"SD-A026382-019で本締結... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "BRACKET仮締め",
"WorkItems": [
"1. ④にBRACKET をかぶせる",
"2. BRACKET 右側面と中のﾚｰﾙの穴位置を合わせて､SCREW で仮締めする(5箇所)",
"3. ④とBRACKET の上面の穴位置を合わせて､SCREW で仮締めする(3箇所)",
"4. ④とBRACKET 右側面下部の穴位置を合わせて､SCREW で仮締めする"
],
"WorkPoints": [
"BR... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "GUIDE取付",
"WorkItems": [
"1. ②のﾚｰﾙをGUIDE の取付穴､左から3番目にGUIDE をｾｯﾄし､上から押し込み取付ける(4箇所)",
"2. ②を反転させ､GUIDE のﾚｰﾙを②の取付穴の右から3番目にｾｯﾄし､上から押し込み取付ける(4箇所)"
],
"WorkPoints": [
"･GUIDE の取付け方向に注意する事(写真参照) ･ｶﾁｯと音がするまで押し込む事",
"･GUIDE の... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM確認",
"WorkItems": [
"■1. PCB-COM の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"■2. PCB-COM のJ1及びPS-ONにｼﾞｬﾝﾊﾟｰﾋﾟﾝが入っている事を確認し､検査書に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-15021",
"InspectionItems": [
"検... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-15021",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM確認",
"WorkItems": [
"■1. PCB-COM の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"■2. PCB-COM のJ1及びPS-ONにｼﾞｬﾝﾊﾟｰﾋﾟﾝが入っている事を確認し､検査書に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-15021",
"InspectionItems": [
"検... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-15021",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM仮取付",
"WorkItems": [
"2. ③のﾚｰﾙ穴と､①の穴位置を合せ､SCREW で仮締めする(8箇所)",
"1. ③の裏面を手前にする"
],
"WorkPoints": [
"SD-A026382-018で本締結",
"･ﾚｰﾙと①の間にINSULATORがある事 ･ﾚｰﾙの右端から3つ目に穴位置を合せる事 ･基板調整の為､仮締めにする事"
],
"Tolks": [],
"Ins... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め1",
"WorkItems": [
"■1. NCIO2 BOARD(PANA) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. ②の指定箇所に､NCIO2 BOARD(PANA) を挿入しながら､PCB-COM基板との差込具合を確認する"
],
"WorkPoints": [
"無理に押し込ま無い事",
"指定箇所は絵参照",
"矢印部を押しながらﾚﾊﾞｰを上げゆっく... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-20005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め1",
"WorkItems": [
"■1. NCIO2 BOARD(PANA) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. ②の指定箇所に､NCIO2 BOARD(PANA) を挿入しながら､PCB-COM基板との差込具合を確認する"
],
"WorkPoints": [
"無理に押し込ま無い事",
"指定箇所は絵参照",
"矢印部を押しながらﾚﾊﾞｰを上げゆっく... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-20005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め1",
"WorkItems": [
"■1. NCIO2 BOARD(PANA) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. ②の指定箇所に､NCIO2 BOARD(PANA) を挿入しながら､PCB-COM基板との差込具合を確認する"
],
"WorkPoints": [
"無理に押し込ま無い事",
"指定箇所は絵参照",
"矢印部を押しながらﾚﾊﾞｰを上げゆっく... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め2",
"WorkItems": [
"1. ②の指定箇所に､①を挿入しながらPCB-COM基板との差込具合を確認する"
],
"WorkPoints": [
"無理に押し込ま無い事",
"ﾌｯｸが確実にかかるか確認する事",
"指定箇所は絵参照",
"差込位置､方向を間違え無い事",
"矢印部を押しながらﾚﾊﾞｰを上げゆっくり取付ける事",
"ここのくぼみ部に基板を差込む事"
]... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "PCB-COM締付",
"WorkItems": [],
"WorkPoints": [
"SD-A026382-015の本締結"
],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "BRACKET締付1",
"WorkItems": [
"1. ①)のﾌﾞﾗｹｯﾄとﾚｰﾙを仮固定したﾈｼﾞ(10-M4X8,SW,PW)を､本締めする(10箇所)",
"2. 青ﾏｰｷﾝｸﾞする(10箇所)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "BRACKET締付2",
"WorkItems": [
"2. ①のﾌﾞﾗｹｯﾄ下部を仮固定したﾈｼﾞ(3-M3X6,SW,PW)を､本締めする(3箇所)→青ﾏｰｷﾝｸﾞ(3箇所)",
"1. ①ﾌﾞﾗｹｯﾄ上面を仮固定したﾈｼﾞ(3-M3X6,SW,PW)を､本締めする(3箇所)→青ﾏｰｷﾝｸﾞ(3箇所)",
"2. ①のﾌﾞﾗｹｯﾄ下部を仮固定したﾈｼﾞ(3-M3X6,SW,PW)を､本締めする(3箇所)→青ﾏｰ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板取付確認",
"WorkItems": [
"1. ①のa部に､外したCPUﾎﾞｰﾄﾞを差込み､奥のPCB-COM基板に挿入しながら､差込不具合を確認し､外す",
"2. ①のb部に､外したCPUﾎﾞｰﾄﾞを差込み､奥のPCB-COM基板に挿入しながら､差込不具合を確認し､外す",
"3. 確認終了後､NCﾎﾞｰﾄﾞを外す"
],
"WorkPoints": [
"･差込位置･方向を間違え無い事 ･無理に押し込ま無い事 ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "ﾌﾞﾗﾝｸﾊﾟﾈﾙ取付",
"WorkItems": [
"1. ②の正面を手前にする",
"3. 青ﾏｰｷﾝｸﾞをする(2箇所)",
"2. ②にPANEL PANEL をﾌﾞﾗｹｯﾄ側に沿わせながらPANEL PANEL (2-付属ﾈｼﾞ)で締付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "電源部取付",
"WorkItems": [
"1. ①に②を挿入しSCREW で取付ける"
],
"WorkPoints": [
"･板金と電源の端を合わせる事 ･ﾈｼﾞを真っ直ぐ入れ､無理に締めこま無い事",
"挿入",
"板金と電源部の端を必ず合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "ﾌｨﾙﾀﾌﾞﾗｹｯﾄ取付",
"WorkItems": [],
"WorkPoints": [
"確実に締結されている事"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨﾙﾀｰ取付",
"WorkItems": [
"1. ②の間にFILTER を挟み込む",
"2. ③の指定箇所に､1の完成品を挿入する"
],
"WorkPoints": [
"･奥まで確実に挿入する事 ･収縮ﾁｭｰﾌﾞを手前にする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PANEL取付",
"WorkItems": [
"1. 電源部のP2･CN4ｺﾈｸﾀを､②の穴に挿入し取付ける(2箇所)",
"2. 電源部ﾈｼﾞ穴と､②の穴位置を確認し､SCREW 締付固定する(5箇所)",
"3. 青ﾏｰｷﾝｸﾞをする(5箇所)"
],
"WorkPoints": [
"･ｶﾁｯというまで確実に押し込む事 ･②の取付方向に注意する事",
"･②はBOXに対し真っ直ぐ取付ける事 ･無理矢理ﾈ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "PANEL取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源配線の接続",
"WorkItems": [
"1. ①の裏面を手前にする",
"3. 青ﾏｰｷﾝｸﾞする(2箇所)",
"2. ①の電源ﾕﾆｯﾄからのP1､J2を､それぞれ指定箇所に差込む"
],
"WorkPoints": [
"･指定箇所は写真参照 ･J2配線をP1配線の内側を通すこと ･ｶﾁｯと音がするまで確実に差込む事"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.