input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "X軸LM取付",
"WorkItems": [
"1. ④にLINEAR-WAY をBOLT BOLT で取付"
],
"WorkPoints": [
"LINEAR-WAY 入荷時の防錆油を拭き取る",
"ｽﾗｲﾀﾞｰがﾚｰﾙより外れない様に注意(終始)",
"LINEAR-WAY の取付方向に注意(下図参照)",
"ﾗｲﾝがある方",
"ﾌﾞﾛｯｸｹﾞｰｼﾞを上図の位置に置き... | {
"QualityItem": "ﾘﾆｱｶﾞｲﾄﾞ平行度",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "±0.01㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "2LG-JG-23004",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "平面度調整①",
"WorkItems": [
"1. ①の平面度を調整"
],
"WorkPoints": [
"LMｽﾗｲﾀﾞｰを上記位置に動かす",
"左右の連結ﾊﾞｰ部のBOLTと上段後左右ﾌﾞﾛｯｸのBOLTを緩め､上面ﾌﾟﾚｰﾄ自体が自由になる状態(上下方向にｶﾀｶﾀ動く)にする",
"ﾊﾝﾄﾞﾙを回してLMｽﾗｲﾀﾞｰ上面から下面ﾌﾟﾚｰﾄの高さを130mmにする"
],
"Tolks": [... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "平面度調整②",
"WorkItems": [
"1. ①の平面度を調整"
],
"WorkPoints": [
"①~④のｽﾗｲﾀﾞｰ上面を測定",
"2箇所のｾｯﾄﾋﾞｽにて平面度を調整目標:0.05mm以内 OK:0.1mm以内※最終平面度測定の後戻り防止の為 0.05mm以内を目指すと良い",
"平面度を調整後､上記2箇所のBOLTを締付",
"SD-A046609-045､04... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "目標:0.05㎜以内(OK:0.10㎜以内)",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "平面度調整②",
"WorkItems": [
"1. ①の平面度を調整"
],
"WorkPoints": [
"①~④のｽﾗｲﾀﾞｰ上面を測定",
"2箇所のｾｯﾄﾋﾞｽにて平面度を調整目標:0.05mm以内 OK:0.1mm以内※最終平面度測定の後戻り防止の為 0.05mm以内を目指すと良い",
"平面度を調整後､上記2箇所のBOLTを締付",
"SD-A046609-045､046の仮固... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "平面度調整②",
"WorkItems": [
"1. ①の平面度を調整"
],
"WorkPoints": [
"①~④のｽﾗｲﾀﾞｰ上面を測定",
"2箇所のｾｯﾄﾋﾞｽにて平面度を調整目標:0.05mm以内 OK:0.1mm以内※最終平面度測定の後戻り防止の為 0.05mm以内を目指すと良い",
"平面度を調整後､上記2箇所のBOLTを締付",
"SD-A046609-045､046の仮固... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "BOX7㎜",
"ToolOther": "95cN･m",
"WorkName": "平面度調整③",
"WorkItems": [],
"WorkPoints": [
"SD-A046609-038の仮固定箇所"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝｹﾞｰｼﾞ",
"Size": "3㎜",
"ToolOther": "",
"WorkName": "X軸ﾘﾆｱｽｹｰﾙ取付",
"WorkItems": [
"1. ①にLINEAR-SCALE を貼付け"
],
"WorkPoints": [
"①の貼付け面を脱脂する事",
"〇穴にﾋﾟﾝｹﾞｰｼﾞを差込み､LINEAR-SCALE を押付けながら貼付ける",
"①の端面に合わせて貼付ける",
"貼付け向きに注意(下図参照)(ﾏｰｸ位置を参照)1.ﾏｰｸは①のﾋﾟﾝｹﾞｰｼﾞ穴側にする事2.ﾏｰｸは定... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "LEDｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にPLATE をSCREW で取付"
],
"WorkPoints": [
"PLATE の保護ｼｰﾄを剥がして取付する事"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "X軸ｽﾗｲﾄﾞﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付"
],
"WorkPoints": [
"BLOCK の取付方向に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ｽﾗｲﾄﾞBAR組立①",
"WorkItems": [
"◆2. 細部に清掃ﾌﾞﾛｰ実施",
"3. 2の完成品にSPRING をBOLT で取付",
"1. BAR のﾊﾞﾘ･打痕の確認"
],
"WorkPoints": [
"全体的に確認(表裏面)",
"SPRING の取付向きに注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"Inspec... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "40cN･m",
"WorkName": "X軸ｽﾗｲﾄﾞBAR組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "X軸ｽﾗｲﾄﾞBAR組立②",
"WorkItems": [
"1. PLATE KNOB にBOLT を⑤で取付",
"2. 1の完成品を①に⑥で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾘﾆｱｴﾝｺｰﾀﾞ組立①",
"WorkItems": [
"1. LINEAR-HEAD の配線にﾏｰｷﾝｸﾞ",
"2. 1の完成品にCABLE ﾗﾍﾞﾙ貼付"
],
"WorkPoints": [
"160mm",
"330mm",
"下記寸法にﾏｰｷﾝｸﾞ",
"貼付け方向に注意(下図参照)※この面に貼付",
"貼付面の中央に傾き無く貼付の事",
"ｺﾈｸﾀ差込み口より見た図",
... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "2LG-JG-23004",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "X軸ﾘﾆｱｴﾝｺｰﾀﾞ組立①",
"WorkItems": [
"1. LINEAR-HEAD の配線にﾏｰｷﾝｸﾞ",
"2. 1の完成品にCABLE ﾗﾍﾞﾙ貼付"
],
"WorkPoints": [
"160mm",
"330mm",
"貼付け方向に注意(下図参照)※この面に貼付",
"貼付面の中央に傾き無く貼付の事",
"ｺﾈｸﾀ差込み口より見た図"
],
"Tolk... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "40cN･m",
"WorkName": "X軸ﾘﾆｱｴﾝｺｰﾀﾞ組立②",
"WorkItems": [
"1. BRACKET に①をBOLT WASHER で取付"
],
"WorkPoints": [
"BRACKET の取付向きに注意(下図参照)",
"BRACKET の状態表示灯が見える様に取付",
"BRACKET の状態表示灯が見える様に取付"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "X軸ﾘﾆｱｴﾝｺｰﾀﾞ組立③",
"WorkItems": [
"1. BRACKET に①をBOLT WASHER で取付"
],
"WorkPoints": [
"①とBRACKET の段差を1mmにする"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Work... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1㎜",
"ToolOther": "",
"WorkName": "X軸ﾘﾆｱｴﾝｺｰﾀﾞ組立③",
"WorkItems": [
"1. BRACKET に①をBOLT WASHER で取付"
],
"WorkPoints": [
"①とBRACKET の段差を1mmにする"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾘﾆｱｴﾝｺｰﾀﾞ組立④",
"WorkItems": [
"1. ①にCABLE-SUPPORT BUSH を取付"
],
"WorkPoints": [
"CABLE-SUPPORT の方向に注意(下図参照)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾟﾚｰﾄ組立①",
"WorkItems": [
"1. PLATE のﾊﾞﾘ･打痕の確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"全体的に確認(表面･裏面)",
"【注意】保護ﾒｶﾞﾈ着用",
"表面",
"裏面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾟﾚｰﾄ組立②",
"WorkItems": [
"3. BLOCK にSPRING-PIN を圧入",
"1. BLOCK のﾊﾞﾘ･打痕確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"SPRING-PIN の方向に注意(下図参照)※横向きならば左右どちらでも良い",
"SPRING-PIN の出代2.5mm",
"全体的に確認",
"【注意】保護ﾒｶﾞﾈ着... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "X軸ﾌﾟﾚｰﾄ組立②",
"WorkItems": [
"3. BLOCK にSPRING-PIN を圧入",
"1. BLOCK のﾊﾞﾘ･打痕確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"SPRING-PIN の方向に注意(下図参照)※横向きならば左右どちらでも良い",
"SPRING-PIN はBLOCK の裏面に圧入する事(下図参照)"
],
"To... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "X軸ﾌﾟﾚｰﾄ組立③",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"②の取付方向に注意(下図参照)",
"①の裏面に取付"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "X軸ﾌﾟﾚｰﾄ組立④",
"WorkItems": [
"1. ①にSTOPPER をSPACER BOLT で取付"
],
"WorkPoints": [
"①の裏面に取付(下図参照)",
"ｻﾞｸﾞﾘ面からBOLTを挿入",
"STOPPER は傾き無き事(矢印方向に押付けながら取付)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "95cN･m",
"WorkName": "X軸ﾌﾟﾚｰﾄ組立⑤",
"WorkItems": [
"1. ①にPLATE をSPACER BOLT で取付"
],
"WorkPoints": [
"PLATE の取付方向に注意(下図参照)",
"広い",
"狭い"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1.5㎜",
"ToolOther": "",
"WorkName": "X軸ﾌﾟﾚｰﾄ組立⑤",
"WorkItems": [
"1. ①にPLATE をSPACER BOLT で取付"
],
"WorkPoints": [
"PLATE の取付方向に注意(下図参照)",
"広い",
"狭い"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "40cN･m",
"WorkName": "X軸ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"ﾋﾟﾝｹﾞｰｼﾞ挿入穴",
"13.5mm",
"②の取付方向に注意(下図参照)",
"取付手順1.ﾋﾟﾝｹﾞｰｼﾞ挿入穴にﾋﾟﾝｹﾞｰｼﾞを挿入し､①と②を貫通させる2.1の状態で①と②の左端寸法を13.5mmにする3.12の状態を保持したままBOLT を... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "13.5㎜",
"ToolOther": "",
"WorkName": "X軸ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"ﾋﾟﾝｹﾞｰｼﾞ挿入穴",
"13.5mm",
"②の取付方向に注意(下図参照)",
"取付手順1.ﾋﾟﾝｹﾞｰｼﾞ挿入穴にﾋﾟﾝｹﾞｰｼﾞを挿入し､①と②を貫通させる2.1の状態で①と②の左端寸法を13.5mmにする3.12の状態を保持したままBOLT を締結する4... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝｹﾞｰｼﾞ",
"Size": "3㎜",
"ToolOther": "",
"WorkName": "X軸ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"ﾋﾟﾝｹﾞｰｼﾞ挿入穴",
"13.5mm",
"②の取付方向に注意(下図参照)",
"取付手順1.ﾋﾟﾝｹﾞｰｼﾞ挿入穴にﾋﾟﾝｹﾞｰｼﾞを挿入し､①と②を貫通させる2.1の状態で①と②の左端寸法を13.5mmにする3.12の状態を保持したままBOLT を締結する4.締結後､... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱ取付",
"WorkItems": [
"1. ①にLINEAR-WAY をBOLT で取付"
],
"WorkPoints": [
"ﾗｲﾝがある方",
"①入荷時の防錆油を拭き取る",
"ｽﾗｲﾀﾞｰがﾚｰﾙより外れない様に注意(終始)",
"①の取付方向に注意(下図参照)",
"ﾋﾟﾝｹﾞｰｼﾞ2本を〇穴に挿入して矢印の方向に押付けながら締結※締結後､ﾋﾟﾝｹﾞｰｼﾞを取外す",
"ﾌﾞ... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "2LG-JG-23004",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "40cN･m",
"WorkName": "Y軸ﾘﾆｱ取付",
"WorkItems": [
"1. ①にLINEAR-WAY をBOLT で取付"
],
"WorkPoints": [
"ﾗｲﾝがある方",
"①入荷時の防錆油を拭き取る",
"ｽﾗｲﾀﾞｰがﾚｰﾙより外れない様に注意(終始)",
"①の取付方向に注意(下図参照)",
"ﾋﾟﾝｹﾞｰｼﾞ2本を〇穴に挿入して矢印の方向に押付けながら締結※締結後､ﾋﾟﾝｹ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "189㎜",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱ取付",
"WorkItems": [
"1. ①にLINEAR-WAY をBOLT で取付"
],
"WorkPoints": [
"ﾗｲﾝがある方",
"①入荷時の防錆油を拭き取る",
"ｽﾗｲﾀﾞｰがﾚｰﾙより外れない様に注意(終始)",
"①の取付方向に注意(下図参照)",
"ﾋﾟﾝｹﾞｰｼﾞ2本を〇穴に挿入して矢印の方向に押付けながら締結※締結後､ﾋﾟﾝｹﾞｰｼﾞを取... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝｹﾞｰｼﾞ",
"Size": "3㎜",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱ取付",
"WorkItems": [
"1. ①にLINEAR-WAY をBOLT で取付"
],
"WorkPoints": [
"ﾗｲﾝがある方",
"①入荷時の防錆油を拭き取る",
"ｽﾗｲﾀﾞｰがﾚｰﾙより外れない様に注意(終始)",
"①の取付方向に注意(下図参照)",
"ﾋﾟﾝｹﾞｰｼﾞ2本を〇穴に挿入して矢印の方向に押付けながら締結※締結後､ﾋﾟﾝｹﾞｰｼﾞを取外す",... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱ取付",
"WorkItems": [
"1. ①にLINEAR-WAY をBOLT で取付"
],
"WorkPoints": [
"ﾗｲﾝがある方",
"①入荷時の防錆油を拭き取る",
"ｽﾗｲﾀﾞｰがﾚｰﾙより外れない様に注意(終始)",
"①の取付方向に注意(下図参照)",
"ﾋﾟﾝｹﾞｰｼﾞ2本を〇穴に挿入して矢印の方向に押付けながら締結※締結後､ﾋﾟﾝｹﾞｰ... | {
"QualityItem": "ﾘﾆｱｶﾞｲﾄﾞ平行度",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "±0.01㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "2LG-JG-23004",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "X軸ﾌﾟﾚｰﾄ補強BAR取付",
"WorkItems": [
"1. ①にPLATE をBOLT で取付"
],
"WorkPoints": [
"PLATE は面一と矢印方向に押付けながら取付",
"PLATE の取付方向に注意(下図参照)",
"ｻﾞｸﾞﾘ側が表面",
"ﾌﾟﾚｰﾄ位置決め穴にｱｸｾｽ出来る様にする"
],
"Tolks": [
"締付ﾄﾙｸ 6... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ取付",
"WorkItems": [
"1. ①にY軸ﾘﾆｱｽﾄｯﾊﾟｰBOLT WASHER を取付",
"2. 1の完成品にSTOPPER をSPACER BOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ取付",
"WorkItems": [],
"WorkPoints": [
"取付位置に注意(下図参照)",
"STOPPER の取付向きに注意(下図参照)",
"ｻﾞｸﾞﾘ側が表面",
"STOPPER に傾き無き事(目視確認)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "Y軸位置決めﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"②の取付向きに注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸位置決めﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"◆2. 1の完成品にｸﾞﾘｰｽ塗布"
],
"WorkPoints": [
"②の下記穴(5箇所)にｸﾞﾘｰｽを塗布",
"②の取付向きに注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "X軸ﾘﾆｱｴﾝｺｰﾀﾞ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"①と②の隙間を0.4mmに調整する事(可動範囲全域)0.3mmが入り､0.5mmが入ら無い事※説明の為､一部の部材を非表示にしています",
"このﾎﾞﾙﾄで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
]... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "隙間ｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾘﾆｱｴﾝｺｰﾀﾞ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"①と②の隙間を0.4mmに調整する事(可動範囲全域)0.3mmが入り､0.5mmが入ら無い事※説明の為､一部の部材を非表示にしています",
"このﾎﾞﾙﾄで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"Inspect... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜が入り0.5㎜が入ら無い事",
"Method": "隙間ｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "X軸ｹｰﾌﾞﾙ固定ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"BRACKET の取付向きに注意(下図参照)",
"BRACKET の折り面を下側にする",
"上図は説明の為､X軸ﾌﾟﾚｰﾄを半透明にしています"
],
"Tolks": [
"締付ﾄﾙｸ 150c... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱｽｹｰﾙ組立①",
"WorkItems": [
"1. PLATE PLATE のﾊﾞﾘ･打痕確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施",
"3. 2の完成品をBOLT で取付"
],
"WorkPoints": [
"全体的に確認",
"【注意】保護ﾒｶﾞﾈ着用",
"PLATE PLATE の取付方向に注意(下図参照)",
"【矢視】C面向き",
"面一にする事"
],... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "40cN･m",
"WorkName": "Y軸ﾘﾆｱｽｹｰﾙ組立①",
"WorkItems": [
"1. PLATE PLATE のﾊﾞﾘ･打痕確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施",
"3. 2の完成品をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "1.1㎜",
"WorkName": "Y軸ﾘﾆｱｽｹｰﾙ組立②",
"WorkItems": [
"2. 1の完成品にLINEAR-SCALE を貼付",
"1. ①のLINEAR-SCALE 貼付け面を脱脂"
],
"WorkPoints": [
"指定箇所(下図赤箇所)を脱脂",
"貼付け向きに注意(下図参照)(ﾏｰｸ位置を参照)①ﾏｰｸは①の上側にする事LINEAR-SCALE ﾏｰｸは定位置ではないので探して確認する事"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾌﾟﾚｰﾄ組立①",
"WorkItems": [
"1. PLATE のﾊﾞﾘ･打痕の確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"全体的に確認(表面･裏面)",
"【注意】保護ﾒｶﾞﾈ着用",
"表面",
"裏面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "Y軸ﾌﾟﾚｰﾄ組立②",
"WorkItems": [
"1. ①にCOVER をSCREW で取付"
],
"WorkPoints": [
"COVER の取付方向に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.94N･m",
"WorkName": "Y軸ﾌﾟﾚｰﾄ組立③",
"WorkItems": [
"1. ①にSTOPPER-BLOCK をBOLT で取付"
],
"WorkPoints": [
"STOPPER-BLOCK の取付位置に注意(①裏面より取付)",
"STOPPER-BLOCK は矢印方向に押し付けながら取付",
"表面",
"裏面"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "Y軸ﾌﾟﾚｰﾄ組立④",
"WorkItems": [
"1. ①にCATCH をBOLT で取付"
],
"WorkPoints": [
"CATCH の取付方向に注意(下図参照)",
"CATCH は下記寸法で取付"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5.5㎜",
"ToolOther": "",
"WorkName": "Y軸ﾌﾟﾚｰﾄ組立④",
"WorkItems": [
"1. ①にCATCH をBOLT で取付"
],
"WorkPoints": [
"CATCH の取付方向に注意(下図参照)",
"CATCH は下記寸法で取付"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "Y軸ﾌﾟﾚｰﾄ組立⑤",
"WorkItems": [
"1. ①にCABLE-SUPPORT をSPACER BOLT WASHER で取付"
],
"WorkPoints": [
"CABLE-SUPPORT の取付方向に注意(下図参照)",
"矢視",
"切りかけあり"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "Y軸ﾌﾟﾚｰﾄ組立⑥",
"WorkItems": [
"1. ①にSPACER BOLT を取付"
],
"WorkPoints": [
"SPACER BOLT の取付場所に注意(表面に取付)",
"表面"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持(右)組立①",
"WorkItems": [
"1. BLOCK のﾊﾞﾘ･打痕の確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施",
"3. 2の完成品にSPRING-PIN を圧入"
],
"WorkPoints": [
"【注意】保護ﾒｶﾞﾈ着用",
"SPRING-PIN の圧入方向に注意(下図参照)",
"SPRING-PIN の出代2mm",
"全体的に確認するが取付面(赤色部分)... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持(右)組立①",
"WorkItems": [],
"WorkPoints": [
"【注意】保護ﾒｶﾞﾈ着用",
"SPRING-PIN の圧入方向に注意(下図参照)",
"全体的に確認するが取付面(赤色部分)は特に注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持(右)組立②",
"WorkItems": [
"1. PLATE PLATE のﾊﾞﾘ･打痕の確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"全体的に確認するが取付面(赤色部分)は特に注意",
"【注意】保護ﾒｶﾞﾈ着用",
"PLATE は表裏面全体"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "部品ﾄﾚｲ支持(右)組立③",
"WorkItems": [
"1. ①をBOLT で取付"
],
"WorkPoints": [
"①の取付方向に注意(下図参照)",
"①の取付は面一､端面合わせにする"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持(右)組立④",
"WorkItems": [
"1. ①に②をBOLT WASHER で仮締結"
],
"WorkPoints": [
"本締結はSD-A046609-105",
"②が自重で傾かない程度で仮締結",
"②の取付方向に注意(下図参照)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持(左)組立①",
"WorkItems": [
"1. BLOCK のﾊﾞﾘ･打痕の確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"【注意】保護ﾒｶﾞﾈ着用",
"全体的に確認するが取付面(赤色部分)は特に注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes"... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持(左)組立②",
"WorkItems": [
"1. PLATE PLATE のﾊﾞﾘ･打痕の確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"全体的に確認するが取付面(赤色部分)は特に注意",
"【注意】保護ﾒｶﾞﾈ着用",
"PLATE は表裏面全体"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "部品ﾄﾚｲ支持(左)組立③",
"WorkItems": [
"1. ①をBOLT で取付"
],
"WorkPoints": [
"①の取付方向に注意(下図参照)",
"①の取付は面一､端面合わせにする"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持(左)組立④",
"WorkItems": [
"1. ①に②をBOLT WASHER で仮締結"
],
"WorkPoints": [
"②が自重で傾かない程度で仮締結",
"②の取付方向に注意(下図参照)",
"本締結はSD-A046609-105"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ組立①",
"WorkItems": [
"1. HANDLE のﾊﾞﾘ･打痕の確認",
"◆2. 細部に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"HANDLE PLATE はｻﾞｸﾞﾘ面の反対側のみ実施",
"【注意】保護ﾒｶﾞﾈ着用",
"ｻﾞｸﾞﾘ面",
"PLATE は表裏面実施"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "30cN･m",
"WorkName": "部品ﾄﾚｲ組立②",
"WorkItems": [
"1. ①②③PLATE PLATE をSCREW で取付"
],
"WorkPoints": [
"①②③PLATE PLATE の取付方向に注意(下図参照)",
"表面",
"裏面",
"PLATE は保護ｼｰﾄを剥がして取付終始､PLATE に傷がつかない様に注意",
"締付ﾄﾙｸに注意(下図参照)"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "部品ﾄﾚｲ組立②",
"WorkItems": [
"1. ①②③PLATE PLATE をSCREW で取付"
],
"WorkPoints": [
"①②③PLATE PLATE の取付方向に注意(下図参照)",
"表面",
"裏面",
"PLATE は保護ｼｰﾄを剥がして取付終始､PLATE に傷がつかない様に注意",
"締付ﾄﾙｸに注意(下図参照)"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "40cN･m",
"WorkName": "Y軸ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"①②の下記指定箇所を面一にした状態でBOLT を締付"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "Y軸ﾘﾆｱｽｹｰﾙ取付",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"②の取付位置に注意(下図参照)",
"②は面一と235.5mmの位置で取付"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱｽｹｰﾙ取付",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"②の取付位置に注意(下図参照)",
"②は面一と235.5mmの位置で取付"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱｴﾝｺｰﾀﾞ取付①",
"WorkItems": [
"1. LINEAR-HEAD の配線にﾏｰｷﾝｸﾞ",
"2. 1の完成品にCABLE ﾗﾍﾞﾙ貼付"
],
"WorkPoints": [
"230mm",
"330mm",
"下記寸法にﾏｰｷﾝｸﾞ",
"貼付け方向に注意(下図参照)※この面に貼付",
"貼付面の中央に傾き無く貼付の事",
"ｺﾈｸﾀ差込み口より見た図",
... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "2LG-JG-23004",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱｴﾝｺｰﾀﾞ取付①",
"WorkItems": [
"1. LINEAR-HEAD の配線にﾏｰｷﾝｸﾞ",
"2. 1の完成品にCABLE ﾗﾍﾞﾙ貼付"
],
"WorkPoints": [
"230mm",
"330mm",
"貼付け方向に注意(下図参照)※この面に貼付",
"貼付面の中央に傾き無く貼付の事",
"ｺﾈｸﾀ差込み口より見た図"
],
"Tolk... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "40cN･m",
"WorkName": "Y軸ﾘﾆｱｴﾝｺｰﾀﾞ取付②",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"②の取付方向に注意(下図参照)※配線が右側",
"矢視",
"①と②の隙間を0.4mmに調整する事(可動範囲全域)0.3mmが入り､0.5mmが入ら無い事※説明の為､一部の部材を非表示にしています"
],
"Tolks": [
"締付ﾄﾙｸ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "隙間ｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "FM-2968",
"WorkName": "Y軸ﾘﾆｱｴﾝｺｰﾀﾞ取付②",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"②の取付方向に注意(下図参照)※配線が右側",
"矢視",
"①と②の隙間を0.4mmに調整する事(可動範囲全域)0.3mmが入り､0.5mmが入ら無い事※説明の為､一部の部材を非表示にしています"
],
"Tolks": [
"締付ﾄﾙｸ 40c... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-2968",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜が入り0.5㎜が入ら無い事",
"Method": "隙間ｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "隙間ｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "FM-2968",
"WorkName": "Y軸ﾘﾆｱｴﾝｺｰﾀﾞ取付②",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"②の取付方向に注意(下図参照)※配線が右側",
"矢視",
"①と②の隙間を0.4mmに調整する事(可動範囲全域)0.3mmが入り､0.5mmが入ら無い事※説明の為､一部の部材を非表示にしています"
],
"Tolks": [
"締付ﾄﾙｸ 40c... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-2968",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜が入り0.5㎜が入ら無い事",
"Method": "隙間ｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "隙間ｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "FM-2968",
"WorkName": "Y軸ﾘﾆｱｴﾝｺｰﾀﾞ取付②",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"②の取付方向に注意(下図参照)※配線が右側",
"矢視",
"①と②の隙間を0.4mmに調整する事(可動範囲全域)0.3mmが入り､0.5mmが入ら無い事※説明の為､一部の部材を非表示にしています"
],
"Tolks": [
"締付ﾄﾙｸ 40c... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-2968",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜が入り0.5㎜が入ら無い事",
"Method": "隙間ｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "Y軸ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ組立①",
"WorkItems": [
"1. ①にPLUNGER をNUT で仮固定",
"2. 1.完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"BRACKET の取付方向に注意(下図参照)BRACKET は面一と12mmの位置で取付",
"矢視",
"本締結:SD-A046609-101"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Y軸ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ組立①",
"WorkItems": [
"1. ①にPLUNGER をNUT で仮固定",
"2. 1.完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"BRACKET の取付方向に注意(下図参照)BRACKET は面一と12mmの位置で取付",
"矢視",
"本締結:SD-A046609-101"
],
"Tolks"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Y軸ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ組立②",
"WorkItems": [
"1. ①のﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ出代を調整"
],
"WorkPoints": [
"仮締結:SD-A046609-100",
"【ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ出代調整方法】1.Y軸位置決めﾌﾟﾚｰﾄ穴にﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬを挿入※ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬと穴位置を合わせる2.穴に挿入した状態で上記寸法を9.5mmにする3.9.5mmを確保した状態でNUTを締結する... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.5㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "2N･m",
"WorkName": "Y軸ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ組立②",
"WorkItems": [
"1. ①のﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ出代を調整"
],
"WorkPoints": [
"仮締結:SD-A046609-100",
"【ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ出代調整方法】1.Y軸位置決めﾌﾟﾚｰﾄ穴にﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬを挿入※ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬと穴位置を合わせる2.穴に挿入した状態で上記寸法を9.5mmにする3.9.5mmを確保した状態でNU... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ組立③",
"WorkItems": [
"◆1. LEVER BUSH にｸﾞﾘｰｽ塗布",
"2. ①にLEVER をBOLT BUSH WASHER WASHER で取付"
],
"WorkPoints": [
"指定箇所に塗布する事",
"LEVER 取付時\"輪っか\"位置に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"In... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "Y軸ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ組立③",
"WorkItems": [
"◆1. LEVER BUSH にｸﾞﾘｰｽ塗布",
"2. ①にLEVER をBOLT BUSH WASHER WASHER で取付"
],
"WorkPoints": [
"指定箇所に塗布する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ組立④",
"WorkItems": [
"◆1. PLATE にｸﾞﾘｰｽ塗布",
"2. ①にPLATE をSPACER BOLT で取付"
],
"WorkPoints": [
"指定箇所に塗布する事※方向注意(下図参照)",
"SPACER の間に\"輪っか\"が入る様に取付※説明の為､PLATE を半透明にしています",
"PLATE 取付後､Y軸の全5箇所位置に問題無く移動､位置固定出... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "Y軸ﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬ組立④",
"WorkItems": [
"◆1. PLATE にｸﾞﾘｰｽ塗布",
"2. ①にPLATE をSPACER BOLT で取付"
],
"WorkPoints": [
"指定箇所に塗布する事※方向注意(下図参照)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "部品ﾄﾚｲ支持取付①",
"WorkItems": [
"1. ①に②③をBOLT WASHER で取付"
],
"WorkPoints": [
"S-PIN挿入穴",
"ﾋﾟﾝｹﾞｰｼﾞ挿入穴",
"【作業手順】1.②のS-PINをS-PIN挿入穴に挿入2.②③にﾋﾟﾝｹﾞｰｼﾞを挿入※入らない場合は横のBOLT(緑〇)を緩め､入る状態で再仮固定3.2の状態でBOLT WASHER で固定",... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝｹﾞｰｼﾞ",
"Size": "3㎜",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持取付①",
"WorkItems": [
"1. ①に②③をBOLT WASHER で取付"
],
"WorkPoints": [
"S-PIN挿入穴",
"ﾋﾟﾝｹﾞｰｼﾞ挿入穴",
"【作業手順】1.②のS-PINをS-PIN挿入穴に挿入2.②③にﾋﾟﾝｹﾞｰｼﾞを挿入※入らない場合は横のBOLT(緑〇)を緩め､入る状態で再仮固定3.2の状態でBOLT WASHER で固定",
"※矢印... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "部品ﾄﾚｲ支持取付②",
"WorkItems": [
"1. ①の高さ調整"
],
"WorkPoints": [
"【調整手順】1.ﾋﾟﾝｹﾞｰｼﾞを挿入した状態のまま､緑〇のBOLTを緩める2.□1を基準にして〇1の高さを\"面一\"にする3.2の手順にて□2~4を基準に〇2~4の高さを\"面一\"にする4.4箇所全て\"面一\"にした状態で緑〇のBOLTを締結する5.ﾋﾟﾝｹﾞｰｼﾞを抜く",
"SD... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "部品ﾄﾚｲ支持取付②",
"WorkItems": [
"1. ①の高さ調整"
],
"WorkPoints": [
"【調整手順】1.ﾋﾟﾝｹﾞｰｼﾞを挿入した状態のまま､緑〇のBOLTを緩める2.□1を基準にして〇1の高さを\"面一\"にする3.2の手順にて□2~4を基準に〇2~4の高さを\"面一\"にする4.4箇所全て\"面一\"にした状態で緑〇のBOLTを締結する5.ﾋﾟﾝｹﾞｰｼﾞを抜く",
"SD... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.1㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ｽﾃｰｼﾞ配線①",
"WorkItems": [
"1. ①にCOVER を貼付"
],
"WorkPoints": [
"貼付け箇所に注意(下図参照)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ｽﾃｰｼﾞ配線②",
"WorkItems": [
"1. ①にCABLE を接続･配線する"
],
"WorkPoints": [
"矢視",
"説明の為､一部の部品を非表示･半透明にしています",
"上記位置168mm~103mmにてｹｰﾌﾞﾙに引っ張り等無き事",
"上昇",
"下降"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ｽﾃｰｼﾞ配線③",
"WorkItems": [
"1. X軸ｴﾝｺｰﾀﾞ配線引き回"
],
"WorkPoints": [
"矢視"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ｽﾃｰｼﾞ配線④",
"WorkItems": [
"1. Y軸ｴﾝｺｰﾀﾞ配線引き回"
],
"WorkPoints": [
"Y軸可動時､配線の干渉が無き事Y軸ﾘﾆｱｽｹｰﾙ下部に注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ｽﾃｰｼﾞ配線⑤",
"WorkItems": [
"1. x､Y軸ﾘﾆｱｴﾝｺｰﾀﾞ配線引き回"
],
"WorkPoints": [
"黄色ﾏｰｷﾝｸﾞ位置でｲﾝｼｭﾛｯｸ固定※赤色線:160mm位置 SD-A046609-062で記載※青色線:230mm位置 SD-A046609-098で記載",
"次の黄色ﾏｰｷﾝｸﾞ迄の間に2本のｲﾝｼｭﾛｯｸを均等の寸法で締付"
],
"Tolks": [],
"Inspec... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "部品ｽﾃｰｼﾞ配線⑥",
"WorkItems": [
"1. X､Y､Zﾘﾆｱｴﾝｺｰﾀﾞ配線引き回"
],
"WorkPoints": [
"Z軸ｴﾝｺｰﾀﾞ",
"Y軸ｴﾝｺｰﾀﾞ",
"X軸ｴﾝｺｰﾀﾞ",
"【作業手順】1,仮固定のｹｰﾌﾞﾙｻﾎﾟｰﾄを外す※方向に注意(図を参照)2,X,Y,Z軸ｴﾝｺｰﾀﾞｹｰﾌﾞﾙをｲﾝｼｭﾛｯｸで固定※固定箇所は図を参照3,ｹｰﾌﾞﾙｻﾎﾟ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "部品ｽﾃｰｼﾞ配線⑥",
"WorkItems": [
"1. X､Y､Zﾘﾆｱｴﾝｺｰﾀﾞ配線引き回"
],
"WorkPoints": [
"Z軸ｴﾝｺｰﾀﾞ",
"Y軸ｴﾝｺｰﾀﾞ",
"X軸ｴﾝｺｰﾀﾞ",
"【作業手順】1,仮固定のｹｰﾌﾞﾙｻﾎﾟｰﾄを外す※方向に注意(図を参照)2,X,Y,Z軸ｴﾝｺｰﾀﾞｹｰﾌﾞﾙをｲﾝｼｭﾛｯｸで固定※固定箇所は図を参照3,ｹｰﾌﾞﾙｻﾎﾟｰﾄを取付",
"黄色ﾏ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴﾝｺｰﾀﾞ調整治具",
"Size": "",
"ToolOther": "FM-6464",
"WorkName": "部品ｽﾃｰｼﾞ配線⑥",
"WorkItems": [
"1. X､Y､Zﾘﾆｱｴﾝｺｰﾀﾞ配線引き回"
],
"WorkPoints": [
"Z軸ｴﾝｺｰﾀﾞ",
"Y軸ｴﾝｺｰﾀﾞ",
"X軸ｴﾝｺｰﾀﾞ",
"【作業手順】1,仮固定のｹｰﾌﾞﾙｻﾎﾟｰﾄを外す※方向に注意(図を参照)2,X,Y,Z軸ｴﾝｺｰﾀﾞｹｰﾌﾞﾙをｲﾝｼｭﾛｯｸで固定※固定箇所は図を参照3,ｹｰﾌﾞﾙｻﾎﾟｰ... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-6464",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "可動全域で緑点灯している事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "完成品検査(平面度)",
"WorkItems": [
"1. ①の上限位置確認",
"2. ①の平面度調整"
],
"WorkPoints": [
"確認場所★=基準 ①②③",
"調整BOLT",
"【調整手順】1,ﾊﾝﾄﾞﾙを回して下面ﾌﾟﾚｰﾄから部品ﾄﾚｲ高さを 138mmにする(左図▲部分(ﾌﾚｰﾑ上面))2,部品ﾄﾚｲ上面4点の平面(★~③)が±0.2mm以内の確認※平面±... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｲﾄｹﾞｰｼﾞ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "完成品検査(平面度)",
"WorkItems": [
"1. ①の上限位置確認",
"2. ①の平面度調整",
"1. ①の上限位置確認",
"2. ①の平面度調整"
],
"WorkPoints": [
"確認場所★=基準 ①②③",
"調整BOLT",
"【調整手順】1,ﾊﾝﾄﾞﾙを回して下面ﾌﾟﾚｰﾄから部品ﾄﾚｲ高さを 138mmにする(左図▲部分(ﾌﾚｰﾑ上面))2,... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法±0.2㎜",
"Method": "ﾊｲﾄｹﾞｰｼﾞ",
"RecordMethod": "2LC-JG-23004",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "完成品検査(平面度)",
"WorkItems": [
"1. ①の上限位置確認",
"2. ①の平面度調整"
],
"WorkPoints": [
"確認場所★=基準 ①②③",
"調整BOLT",
"【調整手順】1,ﾊﾝﾄﾞﾙを回して下面ﾌﾟﾚｰﾄから部品ﾄﾚｲ高さを 138mmにする(左図▲部分(ﾌﾚｰﾑ上面))2,部品ﾄﾚｲ上面4点の平面(★~③)が±0.2mm以内の確認※平面±... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.2㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "滑り止めｼｰﾄ貼付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾞﾗｹｯﾄﾗﾍﾞﾙ貼付け",
"WorkItems": [
"◆1. ﾗﾍﾞﾙ貼付け部の油分を除去する",
"2. STOPPER STOPPER STOPPER BRACKET へLABEL を指定の寸法で貼付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "貼付位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "固定ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にBOLT WASHER を差込み､②をBOLT WASHER にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "固定ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 作業1完成品にBRACKET をBOLT WASHER にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "2.0N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ連結部専用部組立①",
"WorkItems": [
"1. PLATE にINDEX-PLUNGER を取付"
],
"WorkPoints": [
"INDEX-PLUNGER の付属NUTで締結",
"INDEX-PLUNGER の取付方向に注意(下図参照)",
"付属NUT",
"INDEX-PLUNGER の出代 6mm±0.2mm"
],
"Tolks"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各2.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.