input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "FAN組立1",
"Words": [],
"WorkItems": [
"1. ①②に③を⑯⑰⑱⑲で取付ける"
],
"WorkPoints": [
"FLOW方向に注意する事",
"FLOW方向",
"③FUN-GUARDの取付け方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"Wo... | [
{
"WorkName": "FAN組立1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "FAN組立2",
"Words": [
"ﾌﾛﾝﾄ",
"G112R",
"ﾘｱ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"G111R",
"参考;ﾀｲﾒｲﾄ EVO7SP( 締付強度指示値 1.5)"
],
"WorkItems": [
"1. ①②に③を㉗で固定する"
],
"WorkPoints": [
"㉖固定... | [
{
"WorkName": "FAN組立2",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾌﾞｯｼｭ組立",
"Words": [],
"WorkItems": [
"1. BUSH のｺﾞﾑの部分を切り抜く",
"2. 1の完成品をPLATE に取付ける"
],
"WorkPoints": [
"黄丸内のｺﾞﾑを切り抜く",
"切り抜き後､元に組立"
],
"Tolks": [
"締付ﾄﾙｸ 4N･m"
],
"InspectionItems": [],
"InspectionNos": []... | [
{
"WorkName": "ﾌﾞｯｼｭ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "4N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立前準備(17連交換台車仕様時)",
"Words": [],
"WorkItems": [
"1. ①or⑥､VALVE を準備する"
],
"WorkPoints": [
"左側が17連交換台車仕様時は①､17連交換台車切り替え仕様時は⑥を使用する"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■... | [
{
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立前準備(17連交換台車仕様時)",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "員数確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立(17連交換台車仕様時)",
"Words": [
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"参考;ﾀｲﾒｲﾄ EVO7SP( 締付強度指示値 0.5)"
],
"WorkItems": [
"4. 1の完成品に3の完成品を取付ける",
"2. JOINT にCABLE-SUPPORT を㉙で取付ける",
"1. BRACKET にVALVE VALVE をBOLT WASHER で取付ける",
"3. 2... | [
{
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立(17連交換台車仕様時)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNa... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立(30連交換台車仕様時)",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"参考;ﾀｲﾒｲﾄ EVO7SP( 締付強度指示値 0.5)",
"ﾗﾍﾞﾙ"
],
"WorkItems": [
"3. 2の完成品にTUBE を取付、㉙で2箇所固定する",
"4. 1の完成品に3の完成品とJOINT を取付ける",
"1... | [
{
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立(30連交換台車仕様時)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNa... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立前準備(ﾄﾚｲﾌｨｰﾀﾞｰ仕様時)",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"3. 2の完成品に⑥を取付、㉙で2箇所固定する",
"1. ①に⑪を㉓㉔で固定する",
"4. 1の完成品に3の完成品と③を取付ける",
"2. ②に④を㉙で取付ける"
],
"WorkPoin... | [
{
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立前準備(ﾄﾚｲﾌｨｰﾀﾞｰ仕様時)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proc... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾎﾟｽﾄ組立(ﾊﾟﾜｰﾕﾆｯﾄ止め用)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②を締め込む(2本)"
],
"WorkPoints": [
"②が底付きするところで締める"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"Work... | [
{
"WorkName": "ﾎﾟｽﾄ組立(ﾊﾟﾜｰﾕﾆｯﾄ止め用)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ｽﾍﾟｰｻｰ組立(ﾊｰﾈｽ支持用)",
"Words": [],
"WorkItems": [
"1. ①に⑯を締結する"
],
"WorkPoints": [
"ｽﾍﾟｰｻｰのﾀｯﾌﾟｴﾝﾄﾞまで締め込む",
"出代:8mm(参考値)"
],
"Tolks": [
"締付ﾄﾙｸ 3.1N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes"... | [
{
"WorkName": "ｽﾍﾟｰｻｰ組立(ﾊｰﾈｽ支持用)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.1N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "台車駆動用ﾌﾞﾗｹｯﾄ組立",
"Words": [
"この作業では同じものを4個製作"
],
"WorkItems": [
"1. BRACKET にJOINT を取付ける"
],
"WorkPoints": [
"ねじ部(金色部分)をﾅｯﾄとﾂﾗｲﾁ",
"ﾅｯﾄの向きを合わせる事",
"凹側"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos"... | [
{
"WorkName": "台車駆動用ﾌﾞﾗｹｯﾄ組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "天板受けﾌﾞﾗｹｯﾄ組立",
"Words": [
"この作業では同じものを8個製作"
],
"WorkItems": [
"1. ①に②を⑯⑰で取付ける"
],
"WorkPoints": [
"㉘にクランプさせて作業実施"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [... | [
{
"WorkName": "天板受けﾌﾞﾗｹｯﾄ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ｹｰﾌﾞﾙｻﾎﾟｰﾄ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"3. 2の完成品に③を取付ける",
"1. ①を55mmにｶｯﾄする",
"2. ②に①を取付ける"
],
"WorkPoints": [
"①の貼付け位置詳細",
"①の貼付け位置を㉘にて清掃"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "ｹｰﾌﾞﾙｻﾎﾟｰﾄ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ｸﾞﾛﾒｯﾄ前準備1",
"Words": [
"縦横 約20㎜"
],
"WorkItems": [
"1. GROMMET に切り込みを入れる",
"2. 次工程(本体)へ払い出す"
],
"WorkPoints": [
"ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様;4個ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様;3個",
"ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様;切り込み有り⇒4個/切り込み無し⇒4個ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様;切り込み有り⇒3個/切り込み無し⇒5個"
... | [
{
"WorkName": "ｸﾞﾛﾒｯﾄ前準備1",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ｸﾞﾛﾒｯﾄ前準備2",
"Words": [
"縦横 約20㎜"
],
"WorkItems": [
"1. ①に切り込みを入れる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsModels": [
{
"J... | [
{
"WorkName": "ｸﾞﾛﾒｯﾄ前準備2",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "銘板貼付(P692)",
"Words": [
"6mm",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET にLABEL のCX2Rを貼付ける"
],
"WorkPoints": [
"貼付箇所を㉗にて清掃"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
... | [
{
"WorkName": "銘板貼付(P692)",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "6㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【WX専用】Yｽﾄｯﾊﾟｰ組立1",
"Words": [
"取付け方向に注意!①②③⑥部品には方向性があります｡",
"1.5㎜",
"FM-4897"
],
"WorkItems": [
"2. 1完成品に⑥を⑯⑰で取付",
"3. 2完成品に⑦を⑱で取付",
"1. ①②に③④を取付､⑤を挿入(各2個製作)"
],
"WorkPoints": [
"右前･左後用",
"左前･右後用",
... | [
{
"WorkName": "【WX専用】Yｽﾄｯﾊﾟｰ組立1",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "6㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【WX専用】Yｽﾄｯﾊﾟｰ組立2",
"Words": [],
"WorkItems": [
"4. 3完成品と⑥⑦に④を⑤で取付",
"3..2完成品に③を⑲⑳で取付",
"2. 1完成品に②を⑰⑱で取付",
"1.⑥に①を⑯で取付"
],
"WorkPoints": [
"11箇所取付けあり､1箇所のみ向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m... | [
{
"WorkName": "【WX専用】Yｽﾄｯﾊﾟｰ組立2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【WX専用】LMｶﾞｲﾄﾞｽﾗｲﾀﾞｰｸﾞﾘｰｽｴﾙﾎﾞ取付",
"Words": [
"加工面"
],
"WorkItems": [
"1. ①LMｶﾞｲﾄﾞの防錆油をｳｴｽにて拭き取る(ｽﾗｲﾀﾞｰ通過部)",
"2. ｽﾗｲﾀﾞｰを中心に移動させ､⑥を取付"
],
"WorkPoints": [
"拭き取り箇所",
"･⑥が軽く締ったところ(着座)から45度締付ける｡･締めすぎに注意すること｡"
],
"Tolk... | [
{
"WorkName": "【WX専用】LMｶﾞｲﾄﾞｽﾗｲﾀﾞｰｸﾞﾘｰｽｴﾙﾎﾞ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾌﾛﾝﾄACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ前段取り",
"Words": [
"XF",
"YF",
"ｺﾈｸﾀを取外しXYｹｰﾌﾞﾙﾍﾞｱにて使用",
"ｺﾈｸﾀを取り外しPOWER UNITにて使用",
"ｺﾈｸﾀを取外しPOWER UNITにて使用",
"ｺﾈｸﾀを取外しｺﾝﾃﾞﾝｻｰﾊﾞﾝｸにて使用",
"ｺﾈｸﾀを取外しXYｹｰﾌﾞﾙﾍﾞｱにて使用"
],
"WorkItems": [
"■1. ①②の型式確認... | [
{
"WorkName": "ﾌﾛﾝﾄACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ前段取り",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式・製造番号転記",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾌﾛﾝﾄｺﾝﾃﾞﾝｻｰﾊﾞﾝｸ前段取り",
"Words": [],
"WorkItems": [
"■1. ①の型式確認し､ｼﾘｱﾙNo.を検査表に記入"
],
"WorkPoints": [
"型式を確認",
"このｼﾘｱﾙNo.を記入"
],
"Tolks": [],
"InspectionItems": [
"検査表①:2.ﾄﾞﾗｲﾊﾞｰ設定 Front側 (1)型式･検査書ﾁｪｯｸ"
],
"Inspect... | [
{
"WorkName": "ﾌﾛﾝﾄｺﾝﾃﾞﾝｻｰﾊﾞﾝｸ前段取り",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式・製造番号転記",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [
"安全工程"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾌﾛﾝﾄﾄﾞﾗｲﾊﾞｰｺﾈｸﾀ接続",
"Words": [
"ｼｮｰﾄ線廃棄",
"付属治具",
"端子の凹凸面にする",
"N",
"P4",
"NK501",
"P4K501",
"NK502",
"P6K502",
"N",
"P6",
"Y軸 ﾄﾞﾗｲﾊﾞ付属品",
"X軸 ﾄﾞﾗｲﾊﾞ付属品",
"X軸 ﾄﾞﾗｲﾊﾞ付属品",
"P6K502"... | [
{
"WorkName": "ﾌﾛﾝﾄﾄﾞﾗｲﾊﾞｰｺﾈｸﾀ接続",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【WX専用】ﾘｱACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ前段取り",
"Words": [
"XR",
"YR",
"ｺﾈｸﾀを取外しXYｹｰﾌﾞﾙﾍﾞｱにて使用",
"ｺﾈｸﾀを取り外しPOWER UNITにて使用",
"ｺﾈｸﾀを取外しPOWER UNITにて使用",
"ｺﾈｸﾀを取外しｺﾝﾃﾞﾝｻｰﾊﾞﾝｸにて使用",
"ｺﾈｸﾀを取外しXYｹｰﾌﾞﾙﾍﾞｱにて使用"
],
"WorkItems": [
"■1. ①②の... | [
{
"WorkName": "【WX専用】ﾘｱACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ前段取り",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【WX専用】ﾘｱｺﾝﾃﾞﾝｻｰﾊﾞﾝｸ前段取り",
"Words": [],
"WorkItems": [
"■1. ①の型式確認し､ｼﾘｱﾙNo.を検査表に記入"
],
"WorkPoints": [
"型式を確認",
"このｼﾘｱﾙNo.を記入"
],
"Tolks": [],
"InspectionItems": [
"検査表①:2.ﾄﾞﾗｲﾊﾞｰ設定 2-2.Rear側 (1)型式･検査書ﾁｪｯｸ"
],
"... | [
{
"WorkName": "【WX専用】ﾘｱｺﾝﾃﾞﾝｻｰﾊﾞﾝｸ前段取り",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式・製造番号転記",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【WX専用】ﾘｱﾄﾞﾗｲﾊﾞｰｺﾈｸﾀ接続",
"Words": [
"ｼｮｰﾄ線廃棄",
"付属治具",
"端子の凹凸面にする",
"N",
"P4",
"NK503",
"P4K503",
"NK504",
"P6K504",
"N",
"P6",
"Y軸 ﾄﾞﾗｲﾊﾞ付属品",
"X軸 ﾄﾞﾗｲﾊﾞ付属品",
"X軸 ﾄﾞﾗｲﾊﾞ付属品",
"P6K... | [
{
"WorkName": "【WX専用】ﾘｱﾄﾞﾗｲﾊﾞｰｺﾈｸﾀ接続",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ前段取り(ﾌﾛﾝﾄﾄﾞﾗｲﾊﾞｰｺﾈｸﾀｰ取付)",
"Words": [
"端子の凹凸面にする",
"L21K501",
"L11K501",
"L11",
"L21",
"L3K502",
"L1K502",
"L2K502",
"L11K502",
"L21K502",
"L1",
"L2",
"L3",
"L11",
"L21",
... | [
{
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ前段取り(ﾌﾛﾝﾄﾄﾞﾗｲﾊﾞｰｺﾈｸﾀｰ取付)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式・製造番号転記",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【WX専用】ﾊﾟﾜｰﾕﾆｯﾄ前段取り(ﾘｱﾄﾞﾗｲﾊﾞﾞｰｺﾈｸﾀｰ取付)",
"Words": [
"端子の凹凸面にする",
"L21K503",
"L11K503",
"L11",
"L21",
"L3K504",
"L1K504",
"L2K504",
"L21K504",
"L11K504",
"L11",
"L21",
"L1",
"L2",
"... | [
{
"WorkName": "【WX専用】ﾊﾟﾜｰﾕﾆｯﾄ前段取り(ﾘｱﾄﾞﾗｲﾊﾞﾞｰｺﾈｸﾀｰ取付)",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【ﾌﾛﾝﾄ側ﾄﾚｲ仕様時のみ】端子台配線接続",
"Words": [],
"WorkItems": [
"■1. ①の端子台に②を接続する"
],
"WorkPoints": [
"L11c5X1",
"L31c4X1",
"Ec5X1",
"端子のｷﾞｻﾞｷﾞｻﾞが下方向になる様に差込む",
"奥までしっかりと差込む",
"ﾌﾛﾝﾄ側ﾄﾚｲ仕様時のみ接続"
],
"Tolks": [],
"In... | [
{
"WorkName": "【ﾌﾛﾝﾄ側ﾄﾚｲ仕様時のみ】端子台配線接続",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D15",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "導通確認(ﾌﾛﾝﾄ側)",
"Words": [],
"WorkItems": [
"3. 測定値を確認して検査表に記入する",
"1. ﾀｰﾐﾅﾙﾌﾞﾛｯｸ(X111)にﾃｽﾄ棒の黒色を当てる",
"2. ｺﾈｸﾀ(TRAY)のB2端子にﾃｽﾄ棒の赤色を当てる"
],
"WorkPoints": [
"ﾃｽﾄ棒の黒色",
"ﾃｽﾄ棒の赤色",
"A",
"B"
],
"Tolks": [],
"I... | [
{
"WorkName": "導通確認(ﾌﾛﾝﾄ側)",
"QualityItem": "-",
"ToolManageNo": "-",
"ToolName": "ﾃｽﾀｰ",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績表",
"StdVal": "0Ω~0.01Ω",
"Method": "ﾃｽﾀｰ",
"RecordMethod": "WEAV-G002-D15",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "【ﾘｱ側ﾄﾚｲ仕様】端子台配線接続(ﾘｱ側ﾄﾚｲ仕様時)",
"Words": [],
"WorkItems": [
"■1. ①の端子台に②を接続する"
],
"WorkPoints": [
"端子のｷﾞｻﾞｷﾞｻﾞが下方向になる様に差込む",
"奥までしっかりと差込む",
"L11d5X1",
"L31d4X1",
"Ed5X1",
"ﾘｱ側ﾄﾚｲ仕様時のみ接続"
],
"Tolks": [],
... | [
{
"WorkName": "【ﾘｱ側ﾄﾚｲ仕様】端子台配線接続(ﾘｱ側ﾄﾚｲ仕様時)",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D15",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "導通確認(ﾘｱ側)",
"Words": [],
"WorkItems": [
"3. 測定値を確認して検査表に記入する",
"1. ﾀｰﾐﾅﾙﾌﾞﾛｯｸ(X111)にﾃｽﾄ棒の黒色を当てる",
"2. ｺﾈｸﾀ(TRAY)のB2端子にﾃｽﾄ棒の赤色を当てる"
],
"WorkPoints": [
"ﾃｽﾄ棒の黒色",
"ﾃｽﾄ棒の赤色",
"A",
"B"
],
"Tolks": [],
"Ins... | [
{
"WorkName": "導通確認(ﾘｱ側)",
"QualityItem": "-",
"ToolManageNo": "-",
"ToolName": "ﾃｽﾀｰ",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績表",
"StdVal": "0Ω~0.01Ω",
"Method": "ﾃｽﾀｰ",
"RecordMethod": "WEAV-G002-D15",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ整線1",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"60mm",
"ｵﾌﾟｼｮﾝ",
"ｵﾌﾟｼｮﾝ",
"220mm",
"ｵﾌﾟｼｮﾝ",
"ｵﾌﾟｼｮﾝ"
],
"WorkItems": [
"2. 下記配線に黄色ﾏｰｷﾝｸﾞをする｡",
"1. 前準備完成品 のＡＣ線... | [
{
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ整線1",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ整線2",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"mm",
"2ﾋﾞｰﾑ仕様(ﾘｱ側ﾄﾞﾗｲﾊﾞ)ﾘｱ側ﾄﾚｲ",
"ﾌﾛﾝﾄ側ﾄﾞﾗｲﾊﾞP10電源",
"ﾉｲｽﾞﾌｨﾙﾀｰﾌﾛﾝﾄ側ﾄﾚｲ"
],
"WorkItems": [
"1. ①の各配線のFG線を揃えて根元にてｲﾝｼｭﾛｯｸにて束ねる｡",... | [
{
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ整線2",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄにﾌｧｲﾊﾞｰ束線を接続",
"Words": [],
"WorkItems": [
"1. ①の基板側ｺﾈｸﾀｷｬｯﾌﾟを2個取り外す｡",
"2. WXSは②､WXは③のﾌｧｲﾊﾞｰ線を下記名称ｺﾈｸﾀを基板に差込む｡"
],
"WorkPoints": [
"ｶﾁｯと音がするまで差込み､差込後手で抜けないか確認する事",
"ｷｬｯﾌﾟは不要の為､廃棄する｡",
"OPT2",
"OPT1",
"... | [
{
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄにﾌｧｲﾊﾞｰ束線を接続",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄにﾌｧｲﾊﾞｰ束線を固定",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①にﾌｧｲﾊﾞｰ線を固定",
"2. 残りのﾌｧｲﾊﾞｰ線を折れない様に丸めておく｡"
],
"WorkPoints": [
"ﾊﾟﾜｰﾕﾆｯﾄ側のｲﾝｼｭﾛｯｸとﾌｧｲﾊﾞｰ線のｲﾝｼｭﾛｯｸを合わせｲﾝｼｭﾛｯ... | [
{
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄにﾌｧｲﾊﾞｰ束線を固定",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "CPUBOX前段取り",
"Words": [
"AXY",
"****",
"****"
],
"WorkItems": [
"■1. ①のｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入"
],
"WorkPoints": [
"この部分の番号を記入"
],
"Tolks": [],
"InspectionItems": [
"検査表①:7.その他(1)型式･検査書ﾁｪｯｸ"
],
"... | [
{
"WorkName": "CPUBOX前段取り",
"QualityItem": "ｼﾘｱﾙ確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記検査書の有無",
"Method": "目視",
"RecordMethod": "WEAV-G002-D05",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左配管用ﾊｰﾈｽ製作の準備",
"Words": [
":1~2番",
":3番",
":4~9番",
":10~14番",
":15~26番",
":27番"
],
"WorkItems": [
"1.TUBE ,TUBE ,TUBE ,TUBE ,TUBE ,TUBE (TUBE)を下記表の長さに切断する"
],
"WorkPoints": [
"配管の白と黄は､青色ﾏｯｷｰ･配管の黒は､黄色ﾏｰ... | [
{
"WorkName": "左配管用ﾊｰﾈｽ製作の準備",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示寸法各±5㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作1",
"Words": [
"φ6用",
"N076 JOINT 2個を2段にして取付",
"K028 左側ﾏﾆﾎｰﾙﾄﾞ取付",
"1. ①②を取付",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes"... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作1",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作2",
"Words": [
"S 701L / 702L",
"G 701L / 702L",
"1. ①②を引き回す",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"Inspectio... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作2",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作3",
"Words": [
"S 401",
"G 401",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照FT11-N 2個ｲﾝｼｭﾛｯｸ(100㎜) 6本",
"1. ①を引き回す",
"使用治工具No.26",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"2. 引き回し後㉗にて結束し②を結束"
],
"Work... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作3",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作4",
"Words": [
"S 301 / 302",
"G 301",
"1. ①②を引き回す",
"使用治工具No.26",
"G 302"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"Inspe... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作4",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作5",
"Words": [
"S 304L /304R",
"G 304L",
"1. ①②を引き回す",
"使用治工具No.26",
"G 304R"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"In... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作5",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作6",
"Words": [
"S 303L /303R",
"G 303L",
"1. ①②を引き回す",
"使用治工具No.26",
"G 303R"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"In... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作6",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作7",
"Words": [
"S 505L",
"G 505L",
"1. ①を引き回す",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作7",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作8",
"Words": [
"S 502",
"G 502",
"1. ①を引き回す",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"Wo... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作8",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作9",
"Words": [
"S 501",
"G 501",
"1. ①を引き回す",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"Wo... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作9",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作10",
"Words": [
"S 503",
"G 503",
"1. ①を引き回す",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"W... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作10",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作11",
"Words": [
"S 504L",
"G 504L",
"1. ①を引き回す",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作11",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作12",
"Words": [
"S 211",
"G 211",
"1. ①を引き回す",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"W... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作12",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作13",
"Words": [
"結束をする結束位置は､ﾊｰﾈｽ板を参照FT11-N 2個ｲﾝｼｭﾛｯｸ(100㎜) 2本ｲﾝｼｭﾛｯｸ(150㎜) 10本",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照",
"ｲﾝｼｭﾛｯｸ(100mm)"
],
"WorkItems": [
"1. 引き回した配線を㉗㉘①にて結束"
],
"WorkPoints": [
"結束位置は､ﾊｰﾈｽ板を... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作13",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作14",
"Words": [
"1. ①②を引き回す",
"使用治工具No.26",
"S 204L",
"G 202 / 204L",
"S 202L",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照ｲﾝｼｭﾛｯｸ(100㎜) 7本",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"2. 引き回し後､結束"
],
... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作14",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作15",
"Words": [
"結束をする結束位置は､ﾊｰﾈｽ板を参照FT11-N 1個ｲﾝｼｭﾛｯｸ(100㎜) 10本",
"1. ①②③を引き回す",
"使用治工具No.26",
"S 201L",
"G 201L / 203L / 205L",
"S 203L",
"S 205L",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems"... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作15",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作16",
"Words": [
"S 213R / 214R",
"G 213R / 214R",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照FT11-N 1個ｲﾝｼｭﾛｯｸ(100㎜) 4本",
"1. ①②を引き回す",
"使用治工具No.26",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"2. 引き回し後、③㉗で結束... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作16",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作17",
"Words": [
"S 213L/214L",
"G213L/214L",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照FT11-N 1個ｲﾝｼｭﾛｯｸ(150㎜) 7本",
"1. ①②を引き回す",
"使用治工具No.26",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"2. 引き回し後、③㉗で結束"
],... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作17",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作18",
"Words": [
"S 215R/216R",
"G 215R216R",
"使用治工具No.26",
"1. ①②を引き回す"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作18",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作19",
"Words": [
"S 801",
"G 801",
"使用治工具No.26",
"1. ①を引き回す"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"W... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作19",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作20",
"Words": [
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照FT11-N 5個ｲﾝｼｭﾛｯｸ(100㎜) 13本ｲﾝｼｭﾛｯｸ(150㎜) 7本ｲﾝｼｭﾛｯｸ(200㎜) 6本",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"1. 引き回した配線を①㉗㉘㉙で結束"
],
"WorkPoints": [
"結束位置は､ﾊｰ... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作20",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作21",
"Words": [
"K030-1 中継JOINT",
"201L",
"702L",
"701L",
"201L",
"701L",
"702L",
"201L"
],
"WorkItems": [
"1. ①に配管を取付"
],
"WorkPoints": [
"4本の配管を図のように挿入する"
],
"Tolks": [],
... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作21",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作22",
"Words": [
"ｺﾝﾍﾞｱの仕様によってｷｬｯﾌﾟを取付",
"204Lｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時Ф6ｷｬｯﾌﾟ取付け",
"Φ6用",
"1. ①をｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様のみ取付"
],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkT... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作22",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作23",
"Words": [
"303Rﾌﾛﾝﾄ側30連交換台車仕様時はФ6ｷｬｯﾌﾟ取付け",
"304Lﾘｱ側30連交換台車仕様時はФ6ｷｬｯﾌﾟ取付け",
"504Lﾌﾛﾝﾄﾄﾚｲ仕様無し時はФ8ｷｬｯﾌﾟ取付け"
],
"WorkItems": [
"1. JOINT JOINT JOINT JOINT を仕様に合わせ配管に取付"
],
"WorkPoints": [
"供給部の仕様によってｷｬｯﾌﾟ... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作23",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作24",
"Words": [
"303Lﾌﾛﾝﾄ側ﾄﾚｲﾌｨｰﾀﾞｰ仕様時はФ6ｷｬｯﾌﾟ取付け",
"304Rﾘｱ側ﾄﾚｲﾌｨｰﾀﾞｰ仕様時はФ6ｷｬｯﾌﾟ取付け"
],
"WorkItems": [
"1. ①②を仕様に合わせ配管に取付"
],
"WorkPoints": [
"供給部の仕様によってｷｬｯﾌﾟを取付"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作24",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作25(OP:F側ﾄﾚｲｽﾄｯｶｰ仕様時のみ)",
"Words": [
"302ﾄﾚｲｽﾄｯｶｰ仕様時はФ6ｷｬｯﾌﾟ取付け"
],
"WorkItems": [
"1. ①を配管に取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作25(OP:F側ﾄﾚｲｽﾄｯｶｰ仕様時のみ)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作26(OP:F側ﾄﾚｲｽﾄｯｶｰ仕様時のみ)",
"Words": [
"303L/R､304L/Rﾄﾚｲｽﾄｯｶｰ仕様時はJOINTにФ6ｽﾄﾚｰﾄJOINTを取付け",
"401､301､211ﾄﾚｲｽﾄｯｶｰ仕様時はФ6ｽﾄﾚｰﾄJOINTを取付け"
],
"WorkItems": [
"1. ①を配管に取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems"... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作26(OP:F側ﾄﾚｲｽﾄｯｶｰ仕様時のみ)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "左側配管ﾊｰﾈｽ製作27(OP:F側ﾄﾚｲｽﾄｯｶｰ仕様時のみ)",
"Words": [
"501､502､503ﾄﾚｲｽﾄｯｶｰ仕様時はФ8ｽﾄﾚｰﾄJOINTを取付け"
],
"WorkItems": [
"1. ①を配管に取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安... | [
{
"WorkName": "左側配管ﾊｰﾈｽ製作27(OP:F側ﾄﾚｲｽﾄｯｶｰ仕様時のみ)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4934",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右配管用ﾊｰﾈｽ製作の準備",
"Words": [
":1~2番",
":3~4番",
":5~11番"
],
"WorkItems": [
"1.①,②,③(TUBE)を下記表の長さに切断"
],
"WorkPoints": [
"配管の白は､青色ﾏｯｷｰ･配管の黒は､黄色ﾏｰｶｰで配管の両端の先端から約50㎜に配管番号を記入"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "右配管用ﾊｰﾈｽ製作の準備",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作1",
"Words": [
"K029 右i側ﾏﾆﾎｰﾙﾄﾞ取付",
"1. ①を取付",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsModels... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作1",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作2",
"Words": [
"S 701R / 702R",
"G 701R / 702R",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照FT11-N 4個ｲﾝｼｭﾛｯｸ(100㎜) 9本",
"1. ①②を引き回す",
"使用治工具No.26",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"2. 引き回し後、③㉗で結束"... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作2",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作3",
"Words": [
"S 505R",
"E 505R",
"ﾏﾆﾎｰﾙﾄﾞに差込む",
"1. ①を引き回す",
"使用治工具No.26",
"505R"
],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作3",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作4",
"Words": [
"S 504R",
"E 504R",
"ﾏﾆﾎｰﾙﾄﾞに差込む",
"1. ①を引き回す",
"使用治工具No.26",
"504R"
],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作4",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作5",
"Words": [
"S 201R",
"E 201R",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照ｲﾝｼｭﾛｯｸ(100㎜) 3本",
"1. ①を引き回す",
"使用治工具No.26",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"2. 引き回し後､結束"
],
"WorkPoints": [
... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作5",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作6",
"Words": [
"S 203R",
"G 203R",
"1. ①を引き回す",
"使用治工具No.26"
],
"WorkItems": [],
"WorkPoints": [
"ｴｱ配管の基点側をS､終点側をGで表す｡基点側Sから位置合わせをする",
"S(ｽﾀｰﾄ)側に黄色ﾏｰｷﾝｸﾞ位置があるのでﾏｰｷﾝｸﾞする事"
],
"Tolks": [],
"Inspecti... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作6",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作7",
"Words": [
"S 205R",
"G 205R",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照ｲﾝｼｭﾛｯｸ(100㎜) 3本",
"1. ①を引き回す",
"ﾏﾆﾎｰﾙﾄﾞに差込む",
"201R",
"203R",
"205R",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作7",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作8",
"Words": [
"S 215L / 216L",
"G 215L / 216L",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照ｲﾝｼｭﾛｯｸ(150㎜) 8本",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
"WorkItems": [
"1. ①②を引き回す",
"2. 引き回し後､結束"
],
"WorkPoints": [
"... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作8",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作9",
"Words": [
"S 202R / 204R",
"G 202R / 204R",
"引き回し後､結束をする結束位置は､ﾊｰﾈｽ板を参照ｲﾝｼｭﾛｯｸ(100㎜) 5本",
"1. ①②を引き回す",
"使用治工具No.26",
"ﾏﾆﾎｰﾙﾄﾞに差込む",
"204R",
"202R",
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値は､ﾊｰﾈｽ板を参照"
],
... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作9",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作10",
"Words": [
"3本の配管をJOINTへ挿入",
"K030-2中継JOINT",
"K031中継JOINT",
"WXS",
"WX",
"701R",
"702R",
"201R",
"701R",
"702R",
"201R",
"WX",
"WXS",
"701R",
"201R",
"702R",
... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作10",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作11",
"Words": [
"203Rｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時Ф6ｷｬｯﾌﾟ取付け",
"Φ6用",
"ｺﾝﾍﾞｱの仕様によってｷｬｯﾌﾟを取付"
],
"WorkItems": [
"1. ①をｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様のみ取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"Wo... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作11",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "右側配管ﾊｰﾈｽ製作12",
"Words": [
"504Rﾘｱﾄﾚｲ仕様無し時はФ8ｷｬｯﾌﾟ取付け"
],
"WorkItems": [
"1. ①⑥どちらかを仕様に合わせ配管に取付"
],
"WorkPoints": [
"供給部の仕様によってｷｬｯﾌﾟを取付"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
... | [
{
"WorkName": "右側配管ﾊｰﾈｽ製作12",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4933",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "I/O基板用ｽﾍﾟｰｻｰ",
"Words": [],
"WorkItems": [
"1. ①に⑯を締結する"
],
"WorkPoints": [
"ｽﾍﾟｰｻｰのﾀｯﾌﾟｴﾝﾄﾞまで締め込む"
],
"Tolks": [
"締付ﾄﾙｸ 152cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
... | [
{
"WorkName": "I/O基板用ｽﾍﾟｰｻｰ",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "152cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "共通部1工程前ｽﾙｰ部品の確認①",
"Words": [],
"WorkItems": [
"1. BRACKET ~BRACKET ⑦を次工程へ払い出す"
],
"WorkPoints": [
"本体部WX共通部 MTKA013477AAのｽﾙｰ部品を確認し､次工程へ払い出し"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
... | [
{
"WorkName": "共通部1工程前ｽﾙｰ部品の確認①",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "共通部1工程前ｽﾙｰ部品の確認②",
"Words": [],
"WorkItems": [
"1. ①②③④を次工程へ払い出す"
],
"WorkPoints": [
"ﾗｲｾﾝｽｼｰﾙ MTKS000025AAのｽﾙｰ部品を確認し､次工程へ払い出し"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
]... | [
{
"WorkName": "共通部1工程前ｽﾙｰ部品の確認②",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "共通部1工程前ｽﾙｰ部品の確認③",
"Words": [],
"WorkItems": [
"1. ①②③⑥⑦を次工程へ払い出す"
],
"WorkPoints": [
"本体部WX共通部 MTKA014377AAのｽﾙｰ部品を確認し､次工程へ払い出し"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
... | [
{
"WorkName": "共通部1工程前ｽﾙｰ部品の確認③",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "共通部1工程前ｽﾙｰ部品の確認④",
"Words": [],
"WorkItems": [
"1. ①から⑭を次工程へ払い出す"
],
"WorkPoints": [
"⑭はﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様は6個､ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様は5個",
"本体部WX共通部 MTKA013477AAのｽﾙｰ部品を確認し､次工程へ払い出し"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos... | [
{
"WorkName": "共通部1工程前ｽﾙｰ部品の確認④",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "員数確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "共通部1工程前ｽﾙｰ部品の確認⑤",
"Words": [],
"WorkItems": [
"■1. NOISE-FILTER ､NOISE-FILTER ､NOISE-FILTER 型式を確認し次工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [
"検査表①:2.ﾄﾞﾗｲﾊﾞ設定 2-1.Front側 (1)型式･検査書ﾁｪｯｸ"
],
"InspectionNo... | [
{
"WorkName": "共通部1工程前ｽﾙｰ部品の確認⑤",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "員数確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
"Wo... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "WX1工程前ｽﾙｰ部品の確認①",
"Words": [],
"WorkItems": [
"1. BRACKET を次工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsModels": [],
"Jigus": []
} | [
{
"WorkName": "WX1工程前ｽﾙｰ部品の確認①",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "WX1工程前ｽﾙｰ部品の確認②",
"Words": [
"3工程前準備へ払い出し",
"2工程前準備へ払い出し"
],
"WorkItems": [
"1. ①~⑨を次工程へ払い出す"
],
"WorkPoints": [
"②~⑧は本体1工程へ払い出し",
"N001残りﾗﾍﾞﾙ払い出し先 ･緑枠ﾗﾍﾞﾙ1枚は2工程前準備へ ･赤枠ﾗﾍﾞﾙ4枚は3工程前準備へ"
],
"Tolks": [],
"Inspec... | [
{
"WorkName": "WX1工程前ｽﾙｰ部品の確認②",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "員数確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "WX1工程前ｽﾙｰ部品の確認③",
"Words": [],
"WorkItems": [
"1. ①を3工程前準備へ払い出す"
],
"WorkPoints": [
"2ﾋﾞｰﾑ仕様時のみ必要",
"MTKA013012AAのｽﾙｰ部品を確認し､3工程前準備へ払い出し"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
... | [
{
"WorkName": "WX1工程前ｽﾙｰ部品の確認③",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "員数確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "WX1工程前ｽﾙｰ部品の確認④",
"Words": [],
"WorkItems": [
"1. ①を次工程へ払い出す"
],
"WorkPoints": [
"本体部制御 MTKA008059AAのｽﾙｰ部品を確認し､次工程へ払い出す"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"T... | [
{
"WorkName": "WX1工程前ｽﾙｰ部品の確認④",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "員数確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "WX1工程前ｽﾙｰ部品の確認⑤",
"Words": [],
"WorkItems": [
"1. ①を次工程へ払い出す"
],
"WorkPoints": [
"X軸 NPM-WX MTKA009640AAのｽﾙｰ部品を確認し､次工程へ払い出し"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
... | [
{
"WorkName": "WX1工程前ｽﾙｰ部品の確認⑤",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "員数確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
"Wor... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX/WXS ： 1工程前準備（001-）",
"WorkName": "ﾄﾚｲ1工程前ｽﾙｰ部品の確認",
"Words": [
"全削除"
],
"WorkItems": [
"1. SCREW ､JOINT を次工程へ払い出す"
],
"WorkPoints": [
"JOINT はﾌﾛﾝﾄ ﾄﾚｲ仕様時に1個､ﾘｱ ﾄﾚｲ仕様時に1個必要"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": ... | [
{
"WorkName": "ﾄﾚｲ1工程前ｽﾙｰ部品の確認",
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "員数確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ﾍﾞｰｽ加工面確認",
"Words": [],
"WorkItems": [
"1. BASE の赤色部にｱﾙｶﾝｻｽをかける"
],
"WorkPoints": [
"裏 面",
"表 面",
"赤色部にﾊﾞﾘ､打痕等が無い事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolParts... | [
{
"WorkName": "ﾍﾞｰｽ加工面確認",
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ｼｰﾄ貼付",
"Words": [],
"WorkItems": [
"1. ①にSHEET を貼付ける"
],
"WorkPoints": [
"指示箇所にｼｰﾄを貼付け剥がれの無い事",
"貼付け位置 X方向:丸抜き穴ｾﾝﾀｰ Y方向:端面当付け",
"ｼｰﾄ貼付詳細",
"Y方向:端面当付け",
"X方向:左端面合わせ",
"Y方向:端面当付け",
"X方向:丸抜き穴ｾﾝﾀｰ"
... | [
{
"WorkName": "ｼｰﾄ貼付",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ﾋﾟﾝ圧入",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"接着剤塗布 米粒:1",
"FM-2252",
"FM-2252"
],
"WorkItems": [
"1. ①の裏面にPIN を圧入する",
"▲2. PIN のﾃｰﾊﾟｰ側に接着剤を塗布しBLOCK に圧入",
"◆3. 2完成品にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ﾋﾟﾝの外周部にｸﾞﾘｰｽを... | [
{
"WorkName": "ﾋﾟﾝ圧入",
"QualityItem": "出代確認",
"ToolManageNo": "FM-2072",
"ToolName": "Dﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:3㎜",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ﾛｰﾗ部組立",
"Words": [],
"WorkItems": [
"1. ㉖治具(FM-2250)にBEARING を挿入し 上蓋（治具）をｾｯﾄする",
"2. 治具(蓋)の穴にPIN を挿入する",
"3. PIN を圧入する",
"4. 治具(蓋)を外し SPACER を挿入する"
],
"WorkPoints": [
"治具下側の列にﾍﾞｱﾘﾝｸﾞを4個挿入する",
"PIN ﾋﾟﾝの取付方向に注意",
... | [
{
"WorkName": "ﾛｰﾗ部組立",
"QualityItem": "出代確認",
"ToolManageNo": "FM-2250",
"ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ取付",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"1. ①に②を圧入する",
"2. 1完成品にSPACER BEARING をBOLT で取付ける",
"◆3. 2完成品にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄの頭のみにする事",
"ﾍﾞｱﾘﾝｸﾞ(大･小各4個)の外周に塗布する",
"ｽﾍﾟｰ... | [
{
"WorkName": "ﾍﾞｱﾘﾝｸﾞ取付",
"QualityItem": "取付確認",
"ToolManageNo": "FM-6206(001)FM-6206(002)FM-6206(003)",
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"Proces... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2",
"接着剤塗布 ｺﾞﾏ粒:2",
"ﾋﾟﾝに押し当て",
"ﾌﾟﾚｰﾄに押し当て"
],
"WorkItems": [
"▲1. BLOCK にSTOPPER を㉖で取付ける",
"▲2. 1完成品を③にBOLT WASHER で取付ける"
],
"WorkPoints": [
"STOPPER の面取り側を穴の方へ取付ける",
... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "接着剤ｽｰﾊﾟｰXﾎﾜｲﾄ",
"ProcessNames": [
"-"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ﾌﾞﾛｯｸ・ﾜｯｼｬｰ取付",
"Words": [
"ﾌﾟﾚｰﾄに押し当てる",
"ﾋﾟﾝに押し当てる"
],
"WorkItems": [
"1. ①に②をBOLT で取付ける",
"2. 1完成品にWASHER SPACER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"Inspec... | [
{
"WorkName": "ﾌﾞﾛｯｸ・ﾜｯｼｬｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ﾀｰｹﾞｯﾄ取付",
"Words": [],
"WorkItems": [
"1. ①にTARGET を圧入する",
"2. 1完成品に㉘ﾀｰｹﾞｯﾄ保護治具を取付ける"
],
"WorkPoints": [
"面取り側から圧入の事",
"TARGET の圧入方向に注意する事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTyp... | [
{
"WorkName": "ﾀｰｹﾞｯﾄ取付",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4922",
"ToolName": "4ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ﾌﾞﾛｯｸ取付",
"Words": [],
"WorkItems": [
"1. ①にBLOCK BLOCK をBOLT で取付ける"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄの頭のみにする事",
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄの頭のみにする事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "ﾌﾞﾛｯｸ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ﾌﾞﾛｯｸ・ｶﾞｲﾄﾞ取付面確認",
"Words": [],
"WorkItems": [
"1. BLOCK に砥石をかける",
"2. GUIDE GUIDE に砥石をかける"
],
"WorkPoints": [
"全面に砥石をかける事",
"赤色部のみに砥石を掛ける事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTyp... | [
{
"WorkName": "ﾌﾞﾛｯｸ・ｶﾞｲﾄﾞ取付面確認",
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ｼｬｯﾀｰ砥石かけ",
"Words": [
"番号刻印なし"
],
"WorkItems": [
"1. SHUTTER の表面のﾊﾞﾘ･ｶｴﾘ確認を行う",
"2. SHUTTER の裏面のﾊﾞﾘ･ｶｴﾘ確認を行う"
],
"WorkPoints": [
"SHUTTER 表面",
"SHUTTER 裏面",
"番号刻印有り",
"※全体に軽く砥石をかける",
"※表面への砥石･ｱﾙｶﾝｻｽは厳... | [
{
"WorkName": "ｼｬｯﾀｰ砥石かけ",
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： 4ノズルチェンジャー（001-）",
"WorkName": "ｼｬｯﾀｰ取付①",
"Words": [],
"WorkItems": [
"1. ①に②③COLLAR をBOLT で仮固定する",
"2. 1完成品を㉗にｾｯﾄし仮固定ﾎﾞﾙﾄを締結する"
],
"WorkPoints": [
"②の取付け向きに注意する",
"ﾋﾟﾝ当付け",
"ﾋﾟﾝ当付け",
"ｼｬｯﾀｰ当付け",
"ﾌﾞﾛｯｸ当付け",
"当付け後ｸﾗﾝﾌﾟする"
],
"Tol... | [
{
"WorkName": "ｼｬｯﾀｰ取付①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.