input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "RXY配線引き回し8",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. ﾊｰﾈｽﾎﾞｰﾄﾞの指示通りに黄色ﾏｰｷﾝｸﾞをする"
],
"WorkPoints": [
"YEM504",
"X5K504"
... | [
{
"WorkName": "RXY配線引き回し8",
"QualityItem": "作業確認",
"ToolManageNo": "FM-5854",
"ToolName": "NPM-GHXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "RXY配線引き回し9",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"YEM501",
"X5K501"
],
"Tolks": [],
"InspectionIte... | [
{
"WorkName": "RXY配線引き回し9",
"QualityItem": "作業確認",
"ToolManageNo": "FM-5854",
"ToolName": "NPM-GHXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "RXY配線引き回し10",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CN1",
"HR_K313"
],
"Tolks": [],
"InspectionItem... | [
{
"WorkName": "RXY配線引き回し10",
"QualityItem": "作業確認",
"ToolManageNo": "FM-5854",
"ToolName": "NPM-GHXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "RXY配線引き回し11",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に202を書く"
],
"WorkPoints": [
"Φ6黒配管",
"Φ6黒配管"
],
"Tolks":... | [
{
"WorkName": "RXY配線引き回し11",
"QualityItem": "作業確認",
"ToolManageNo": "FM-5854",
"ToolName": "NPM-GHXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "RXY配線引き回し12",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に302を書く"
],
"WorkPoints": [
"Φ6黄配管",
"Φ6黄配管"
],
"Tolks":... | [
{
"WorkName": "RXY配線引き回し12",
"QualityItem": "作業確認",
"ToolManageNo": "FM-5854",
"ToolName": "NPM-GHXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "RXY配線引き回し13",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CN6",
"CN2",
"1A22",
"HRPWA11"
],
"Tolks... | [
{
"WorkName": "RXY配線引き回し13",
"QualityItem": "作業確認",
"ToolManageNo": "FM-5854",
"ToolName": "NPM-GHXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "RXY配線引き回し14",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CN7",
"B113R"
],
"Tolks": [],
"InspectionItems"... | [
{
"WorkName": "RXY配線引き回し14",
"QualityItem": "作業確認",
"ToolManageNo": "FM-5854",
"ToolName": "NPM-GHXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "ﾊｰﾈｽ引き回し確認2",
"Words": [
"HRPWA11",
"CN2",
"XBK508",
"Φ6黒",
"HR_K313",
"XBK504",
"Φ6黄",
"XBK503",
"HRPWA11",
"CN2",
"XBK508",
"Φ6黒",
"HR_K313",
"XBK504",
"Φ6黄",
"XBK503",
... | [
{
"WorkName": "ﾊｰﾈｽ引き回し確認2",
"QualityItem": "引き回確認",
"ToolManageNo": "FM-5854",
"ToolName": "NPM-GHXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布1",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:各1",
"ｸﾞﾘｰｽ塗布 小豆:1ﾘﾝｸ当たり各2"
],
"WorkItems": [
"◆1. CABLE-BEAR CABLE-BEAR 付属のリンクプレートの内側に㉖を塗布する",
"◆2. CABLE-BEAR CABLE-BEAR の内側に㉖を塗布する"
],
"WorkPoints": [],
"Tolks": [],
"Inspectio... | [
{
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布1",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽKS-63W",
"ProcessNames": [
"作業者安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布2",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1ｹｰﾌﾞﾙ当たり各4"
],
"WorkItems": [
"1. ①②のｹｰﾌﾞﾙｻﾎﾟｰﾄにｲﾝｼｭﾛｯｸを通す(1枚2箇所×8枚)",
"◆2. ①②の下記指示部に㉗を塗布する"
],
"WorkPoints": [
"ｹｰﾌﾞﾙﾀｲの頭が､ｹｰﾌﾞﾙｻﾎﾟｰﾄの下面にくるように取付ける事",
"ｼﾘｺﾝｸﾞﾘｰｽ塗布"
],
"Tolk... | [
{
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布2",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布1ｹｰﾌﾞﾙ当たり小豆:各4",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽKS-63W",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "X軸ﾍﾞｱ取付け",
"Words": [
"CN7",
"黒色配管",
"XEM503",
"CN1",
"1A22",
"黄色配管",
"CN6",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白色配管",
"XMM503",
"白色配管",
"CMRP",
"(ｹｰﾌﾞﾙﾍﾞｱ内側)",
... | [
{
"WorkName": "X軸ﾍﾞｱ取付け",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "Y軸ﾍﾞｱ取付け",
"Words": [
"白色配管",
"4K303",
"白色配管",
"XBK503",
"XBK508",
"XBK504",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"黒色配管",
"黄色配管",
"HR_K313",
"CN2",
"HRPWA11",
"X5K508"... | [
{
"WorkName": "Y軸ﾍﾞｱ取付け",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：XY軸R側配線 (001-025）",
"WorkName": "外観確認",
"Words": [],
"WorkItems": [
"1. ①の外観を確認する"
],
"WorkPoints": [
"CN6",
"1A22",
"黄色配管",
"黒色配管",
"CN1",
"XEM503",
"Y軸ﾍﾞｱ",
"X軸ﾍﾞｱ",
"CMRP",
"白色配管",
"XMM503",
"4K303",
"白色配管"... | [
{
"WorkName": "外観確認",
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線・配管によじれが無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り1",
"Words": [],
"WorkItems": [
"1. BEARING にPIN を圧入"
],
"WorkPoints": [
"｢8.12ﾉｽﾞﾙ｣側を使用する 刻印注意",
"治具のﾋﾟﾝがある方にﾍﾞｱﾘﾝｸﾞをｾｯﾄする",
"ﾃｰﾊﾟｰ側を上にして挿入",
"治具の上側を被せPIN を挿入し圧入",
"FM-2250(上側)",
"治具... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り1",
"QualityItem": "取付確認",
"ToolManageNo": "FM-2250",
"ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り2",
"Words": [
"接着剤塗布 米粒:1",
"39mm"
],
"WorkItems": [
"▲1. PIN に接着剤を塗布しBLOCK に圧入"
],
"WorkPoints": [
"治具PIN にPIN を挿入し圧入",
"ﾋﾟﾝ出代:39㎜",
"ﾋﾟﾝのﾃｰﾊﾟ側に塗布する事",
"治具BLOCK にBLOCK を挿入",
... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り2",
"QualityItem": "寸法確認",
"ToolManageNo": "FM-2252",
"ToolName": "ﾊﾞﾈｶﾞｲﾄﾞ､Dﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り3",
"Words": [
"3mm",
"3mm"
],
"WorkItems": [
"1. BLOCK に砥石を掛ける",
"2. 1完成品にPIN を圧入"
],
"WorkPoints": [
"面取り部を上側にしてｾｯﾄする",
"治具(上側)を被せPIN を入れ圧入",
"ﾋﾟﾝ圧入面の裏表面に掛ける事",
"FM-2253(下側)... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り3",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、傷等無き事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り4",
"Words": [
"接着剤塗布 米粒:2"
],
"WorkItems": [
"▲1. STOPPER に接着剤塗布",
"2. 1.完成品にBLOCK を挿入"
],
"WorkPoints": [
"STOPPER を挿入する前に接着剤を塗布",
"ﾃｰﾊﾟｰ側を挿入",
"飛び出した接着剤はふき取る事",
"挿入後はしっかり乾燥させる事"... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り4",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｽｰﾊﾟｰX",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り5",
"Words": [],
"WorkItems": [
"1. BASE に油砥石(ｱﾙﾐ用)をかける"
],
"WorkPoints": [
"加工面をかけ､ﾊﾞﾘがないか確認",
"表面",
"裏面"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り5",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り6",
"Words": [
"1.5mm"
],
"WorkItems": [
"1. ①にPIN を圧入"
],
"WorkPoints": [
"ﾃｰﾊﾟｰ側を圧入",
"座ｸﾞﾘ有りが表面",
"出代詳細"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTy... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立前段取り6",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "圧入台",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立1",
"Words": [],
"WorkItems": [
"1. ①にSPACER を通し③に圧入"
],
"WorkPoints": [
"奥まで差込む事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立1",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "圧入台",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立2",
"Words": [],
"WorkItems": [
"1. ①にHOLDER をBOLT で取付"
],
"WorkPoints": [
"ﾍﾞｰｽのDﾋﾟﾝに挿入した後にBOLT を締結",
"先に挿入",
"挿入後締結"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"Inspect... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立3",
"Words": [],
"WorkItems": [
"1. BOLT にBEARING SPACER を通し①に取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"▲特殊作業",
"●ク... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立4",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"ﾃｰﾊﾟｰ側を下側にして挿入"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"▲特殊作業"... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立4",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立5",
"Words": [],
"WorkItems": [
"1. BOLT にWASHER SPACER を通し①に取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"▲特殊作業",
"●クリ... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立5",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立6",
"Words": [
"定盤"
],
"WorkItems": [
"1. GUIDE に①をBOLT で取付"
],
"WorkPoints": [
"定盤上で締付け実施",
"定盤に押し当てながら締結"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos"... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立6",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立7",
"Words": [],
"WorkItems": [
"1. BOLT でSHUTTER BLOCK COLLAR GUIDE を組立",
"2. 1の完成品にBOLT でCOLLAR ④を取付"
],
"WorkPoints": [
"仮組立品を㉘治具に取付",
"GUIDE を治具のDﾋﾟﾝに当てつけ",
"全体を矢印方向に押し治具に当てﾚﾊﾞｰで固定する",
"2箇... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立7",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立8",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆1. ①のﾍﾞｱﾘﾝｸﾞ(8か所)にｸﾞﾘｰｽを塗布",
"2. ①に②を挿入し､COLLAR BOLT で取付"
],
"WorkPoints": [
"取付注意点1",
"定盤にて取付した基準面",
"矢印方向から均等に押し当てて締結",
"取付注意点2",
... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ組立8",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"Words": [
"▲特殊作業",
"接着剤塗布 米粒:1"
],
"WorkItems": [
"2. ①に治具を差込み②をWASHER とBOLT で取付",
"▲1. BOLT に接着剤塗布"
],
"WorkPoints": [
"ﾎﾞﾙﾄの先端に接着剤塗布",
"治具にｼｬｯﾀｰを押し当て",
"②のｽﾄｯﾊﾟｰをｼｬｯﾀｰﾌﾚｰﾑに押し当て増し締め",
... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ﾛｯｸﾀｲﾄ242/243",
"ProcessNames": [
"特殊工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1"
],
"WorkItems": [
"◆1. ①のﾋﾟﾝとWASHER にｸﾞﾘｰｽ塗布",
"3. GUIDE にWASHER を貼付し､BOLT WASHER で取付",
"2. ①にSPRING を挿入"
],
"WorkPoints": [
"ﾋﾟﾝ全体にｸﾞﾘｰｽ塗布",
... | [
{
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾌﾞﾛｯｸとｽﾍﾟｰｻｰ取付け",
"Words": [],
"WorkItems": [
"1. ①にBLOCK BLOCK をBOLT で取付",
"2. ①にSPACER をBOLT で取付"
],
"WorkPoints": [
"BLOCK BLOCK をﾋﾟﾝに挿入してから締結する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
... | [
{
"WorkName": "ﾌﾞﾛｯｸとｽﾍﾟｰｻｰ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ﾌﾞﾛｯｸとﾄﾞｸﾞ取付け",
"Words": [],
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付",
"2. ①にDOG をWASHER BOLT で取付"
],
"WorkPoints": [
"取付位置詳細",
"㉚を挟み取付け"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"In... | [
{
"WorkName": "ﾌﾞﾛｯｸとﾄﾞｸﾞ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "ｼｬｯﾀｰ動作確認",
"Words": [],
"WorkItems": [
"1. ｼｬｯﾀｰの動作確認実施"
],
"WorkPoints": [
"4N以下で合格",
"ｼｬｯﾀｰをﾌﾟｯｼｭｹﾞｰｼﾞで押し､ｽﾄﾛｰｸ全域での最大荷重を測定"
],
"Tolks": [],
"InspectionItems": [
"検査表①:ｼｬｯﾀｰ動作確認"
],
"InspectionNos":... | [
{
"WorkName": "ｼｬｯﾀｰ動作確認",
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "4N以下",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C08",
"Others": "-",
"ProcessNames": [
"作業者安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "銘板・警告ﾗﾍﾞﾙ貼付け",
"Words": [],
"WorkItems": [
"2. ①の完成品に⑨を貼付",
"1. ①にLABEL LABEL LABEL を貼付"
],
"WorkPoints": [
"LABEL はQRｺｰﾄﾞの中心が寸法の端"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": ... | [
{
"WorkName": "銘板・警告ﾗﾍﾞﾙ貼付け",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(FC16)) (001-021）",
"WorkName": "機能検査",
"Words": [],
"WorkItems": [
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ脱着確認",
"2. ﾉｽﾞﾙｾｯﾄ確認"
],
"WorkPoints": [
"着脱の際､引っかかりなく着脱できる事",
"ﾁｪﾝｼﾞｬｰを治具の上にｾｯﾄ(ﾚﾊﾞｰを押さない状態)",
"治具のﾚﾊﾞｰを押すと自重にて落下する事",
"治具との隙間無き事",
"ｼｬｯﾀｰを開いてﾉｽﾞﾙが32... | [
{
"WorkName": "機能検査",
"QualityItem": "脱着確認",
"ToolManageNo": "FM-2411",
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬ確認治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "引っ掛かりが無い事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C08",
"Others": "-",
"ProcessNames": [
"作業者安... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立①",
"Words": [
"この作業では同じものを4個製作"
],
"WorkItems": [
"1. BLOCK に砥石をかける",
"2. BLOCK にGREASE-NIPPLE を取付ける",
"3. 2完成品にJOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 110cN･m"
],... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立②",
"Words": [
"17㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET にBOLT WASHER を取付ける",
"2. BRACKET にCOVER を取付ける"
],
"WorkPoints": [
"COVER の取付位置を脱脂する事",
"この作業では同じものを2個製作"
],
"Tolks": [
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立③",
"Words": [
"確認補助具",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で仮付けする",
"2. 1完成品にWASHER BOLT を仮付けする",
"3. 2完成品を確認補助具で調整して固定する"
],
"WorkPoints": [
"幅調整して固定する",
"①②の面を合わせて取付ける事",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立④",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②③④⑤を貼付ける",
"2. 1完成品に②③④⑥を貼付ける"
],
"WorkPoints": [
"貼付位置を脱脂する事",
"貼付位置を脱脂する事",
"②③④⑤の貼付位置､寸法を確認して貼付ける事",
"②③④⑥の貼付位置､寸法を確認して貼付ける事"
],
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立④",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑤",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"3. 2完成品にCLIP をBOLT で取付ける",
"2. ①にCLIP をSPACER BOLT で取付ける(3箇所)",
"1. ①にCLIP をBOLT で取付ける"
],
"WorkPoints": [
"CLIP の方向い注意して取付ける事",
"①の裏面に取付ける事",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑤",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑥",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にCABLE-SUPPORT CLIP をBOLT で取付ける",
"2. 1完成品に⑤をBOLT WASHER で取付ける"
],
"WorkPoints": [
"⑤に傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 95cN･m... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑥",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑦",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②を③で取付ける",
"3. ①に 2完成品を取付ける",
"2. ④に⑯を取付ける"
],
"WorkPoints": [
"矢印方向に当付けて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑦",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑧",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. COUPLER にBRACKET をSPACER BOLT WASHER で取付ける",
"2. 1完成品にBRACKET BRACKET をBOLT で仮付ける"
],
"WorkPoints": [
"本締工程:SD-A033027-047"
],
"Tolks": [
"締付ﾄﾙ... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑧",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑨",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にLABEL を貼付ける",
"2. ②にLABEL を貼付ける"
],
"WorkPoints": [
"LABEL の貼付方向に注意する事",
"LABEL の貼付方向に注意する事"
],
"Tolks": [],
"InspectionItems": [],
"In... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑨",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立①",
"Words": [
"表 面",
"裏 面",
"4㎜",
"4㎜",
"表 面",
"表 面",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①の両面に砥石をかける",
"2. 1完成品にPIN を圧入する(4箇所)",
"3. 2完成品にPIN を圧入する(4箇所)"
],
"WorkPoints": [
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立②",
"Words": [
"裏 面",
"7㎜",
"5㎜",
"表 面",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. X-PLATE の両面に砥石をかける",
"2. X-PLATE にPIN を圧入する"
],
"WorkPoints": [
"各々ﾋﾟﾝ出代が違うので注意する事",
"PIN ﾋﾟﾝ出代:7㎜",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立②",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立③",
"Words": [
"A",
"B",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBOLT CLIP を取付ける"
],
"WorkPoints": [
"A視野 (左側面) : 3箇所",
"正 面 : 2箇所",
"B視野 (右側面) : 5箇所",
"BOLT の取付方向や位置を間違えないように取付ける事(下図参... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立④",
"Words": [],
"WorkItems": [
"1. ①にSPACER STOPPER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立④",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑤",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"2. FAN にLABEL を取付ける",
"■1. FAN の型式･ｼﾘｱﾙ(lot)№を確認し､検査書にﾁｪｯｸ及びｼﾘｱﾙを記入する",
"3. ①にFAN をBOLT WASHER で取付ける"
],
"WorkPoints": [
"FANの裏表に注意する事 (型式ﾗﾍﾞﾙが見え無い事)",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑤",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C06",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑥",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBOLT WASHER を挿入する",
"2. 1完成品にBRACKET をBOLT で取付ける",
"3. 2完成品に③をBOLT WASHER で取付ける"
],
"WorkPoints": [
"③を矢印方向に押し当てる事",
"BRACKET を矢印方向に押し当てる事"
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑥",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立➆",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"DS05BCD1ANAA4P0",
"型式",
"Ser.№",
"この作業では同じものを2個製作"
],
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"■2. ①にMOTOR をBOLT ... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立➆",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C06",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立①",
"Words": [
"②の取付面に砥石を掛ける",
"読取り面",
"矢印方向に当付ける",
"型式",
"Ser.№",
"S/N ※※※※※※※※",
"Model ST778CA-0500E-PF"
],
"WorkItems": [
"1. ②の型式を確認し､ｼﾘｱﾙNoを検査書に転記する",
"3. 2完成品に④を⑯⑰で取付ける",
"2. ①... | [
{
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立①",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C06",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立②",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"60㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"2. 1完成品にCLIP をBOLT で取付ける",
"4. 3完成品の配線を㉙ｲﾝｼｭﾛｯｸで固定する",
"3. 2完成品にBOLT WASHER WASHER を挿... | [
{
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立①",
"Words": [
"91㎜",
"10㎜",
"5㎜",
"5㎜"
],
"WorkItems": [
"1. BRACKET にCOVER 貼付ける",
"2. BRACKET にCLIP をBOLT で取付ける",
"3. BRACKET にCLIP をBOLT で取付ける",
"4. BRACKET にLABEL を貼付ける"
],
"WorkPoin... | [
{
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立②",
"Words": [
"①(②)と③の端面を合わせる事(黄点線)"
],
"WorkItems": [
"1. BRACKET (②)にBRACKET をNUT SCREW SCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立③",
"Words": [
"長い",
"短い",
"短い",
"長い"
],
"WorkItems": [
"1. ①②にROD をBOLT WASHER で取付ける",
"3. 2完成品にROD とBRACKET をSCREW とBOLT WASHER で取付ける",
"2. 1完成品にSCREW を取付ける"
],
"WorkPoints": [
"RODをｽﾊ... | [
{
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "X軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立①",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2"
],
"WorkItems": [
"1. ①②にBRACKET をSCREW で取付ける",
"2. 1 完成品にSHEET を貼付ける",
"▲3. 2完成品にWASHER を貼付ける"
],
"WorkPoints": [
"①(②)とWASHER の円中心を合わせる",
"①(②)とBRACKET の水平を合わせる事",
... | [
{
"WorkName": "X軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "X軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立②",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各2",
"1㎜",
"25㎜",
"1㎜",
"この部分を持ってXﾋﾞｰﾑを移動し無い事 / Do not ･･･",
"141㎜",
"2㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"▲1. BRACKET にWASHER を貼付ける",
"2. 1完成品にSHEET ... | [
{
"WorkName": "X軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ｵｲﾙﾊﾟﾝ組立",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各2",
"166㎜",
"1㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. COVER にLABEL を貼付ける",
"▲2. 1完成品にTRIM を取付ける"
],
"WorkPoints": [
"㉘を内側に塗布する事",
"この面にLABEL を貼付ける事",
"LABEL ... | [
{
"WorkName": "ｵｲﾙﾊﾟﾝ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾊﾝﾄﾞﾙ組立",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. HANDLE にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
... | [
{
"WorkName": "ﾊﾝﾄﾞﾙ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "BEAM加工面確認",
"Words": [
"砥石かけ面",
"A",
"B",
"C",
"D",
"E",
"F",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. X-BEAM の加工面に砥石をかける"
],
"WorkPoints": [
"A矢視",
"B矢視",
"C矢視",
"D矢視",
"ﾊ... | [
{
"WorkName": "BEAM加工面確認",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "PIN圧入",
"Words": [
"2.5㎜",
"9.5㎜",
"2㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にPIN PIN を圧入する",
"2. 1完成品にPIN を圧入する"
],
"WorkPoints": [
"PIN ﾋﾟﾝ出代:2.5㎜",
"PIN ﾋﾟﾝ出代:9.5㎜\u000b測定箇所に注意する事(図参照)",
"... | [
{
"WorkName": "PIN圧入",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "銘板貼付①",
"Words": [
"1㎜",
"1㎜",
"2㎜",
"3㎜",
"F側",
"R側",
"190㎜",
"331.5㎜",
"80㎜",
"5㎜",
"5㎜"
],
"WorkItems": [
"1. ①にLABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"左右同一寸法",
... | [
{
"WorkName": "銘板貼付①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾏｳﾝﾄ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にCLIP をBOLT で取付ける"
],
"WorkPoints": [
"45度傾けるて取付ける事",
"45度傾け取付ける事",
"F側は12箇所､R側は13箇所取付ける事",
"R側のみに取付ける事",
"45度傾け取付ける事"
],
"Tolks": [
"... | [
{
"WorkName": "ﾏｳﾝﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ｸﾞﾘｰｽﾆｯﾌﾟﾙ・ｼﾞｮｲﾝﾄ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にGREASE-NIPPLE を取付ける",
"2. 1完成品にJOINT を取付ける",
"3. 2完成品にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締... | [
{
"WorkName": "ｸﾞﾘｰｽﾆｯﾌﾟﾙ・ｼﾞｮｲﾝﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ｶｰﾎﾞﾝﾌﾟﾚｰﾄ・ﾊﾝﾄﾞﾙ取付",
"Words": [
"取付け方向に注意!この部品には方向性があります",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にPLATE をBOLT で取付ける",
"2. 1完成品に④をBOLT WASHER で取付ける"
],
"WorkPoints": [
"取手取付位置も中心で取付ける事(黄色〇部)",
"BOLT はﾈｼﾞ穴中心で取付... | [
{
"WorkName": "ｶｰﾎﾞﾝﾌﾟﾚｰﾄ・ﾊﾝﾄﾞﾙ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "銘板貼付②",
"Words": [
"2㎜",
"10㎜",
"2㎜",
"10㎜",
"F側",
"R側",
"F側",
"R側",
"F側",
"R側",
"42㎜",
"323.5㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"2. ②にLABEL LABEL を貼付ける",
"1. ①にLABEL ... | [
{
"WorkName": "銘板貼付②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾌﾞﾗｹｯﾄの取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBRACKET をBOLT で仮止めする",
"2. 1完成品のBRACKET にWASHER BOLT を仮止めする",
"3. 2完成品のBRACKET をWASHER BOLT で取付ける"
],
"WorkPoints": [
"本締め工程SD-A033027-048",
"本締め工... | [
{
"WorkName": "ﾌﾞﾗｹｯﾄの取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾘﾆｱｳｴｲ取付",
"Words": [
"THK",
"YKH15202",
"ﾘﾆｱｶﾞｲﾄﾞ基準位置",
"TKH166-1",
"TKH166-2",
"TKH166-KB-1",
"TKH166-KB-2",
"基準ﾋﾟﾝ位置",
"基準",
"上段ﾚｰﾙ(従動側)",
"下段ﾚｰﾙ(基準KB側)",
"基準D",
"基準D",
"基準",
... | [
{
"WorkName": "ﾘﾆｱｳｴｲ取付",
"QualityItem": "ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C06",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾘﾆｱｳｴｲ平行調整",
"Words": [
"88㎜",
"基準側にｾｯﾄ",
"反基準(上段)",
"基準側(下段)",
"LMｶﾞｲﾄﾞ取付面",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①を㉗に仮締結する",
"3. 基準側ﾚｰﾙ(下段)の真直度を調整する",
"4. 反 基準側ﾚｰﾙ(上段)の平行度を調整する",
"2. ①を㉙と平行になる... | [
{
"WorkName": "ﾘﾆｱｳｴｲ平行調整",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4412",
"ToolName": "Xﾋﾞｰﾑ組立治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾘﾆｱｳｴｲ精度確認",
"Words": [
"ﾌﾞﾛｯｸ№1",
"ﾌﾞﾛｯｸ№2",
"ﾌﾞﾛｯｸ№3",
"ﾌﾞﾛｯｸ№4",
"この作業では同じものを2個製作",
"削除"
],
"WorkItems": [
"1. ﾌｫｰｽｹﾞｰｼﾞにて､ﾘﾆｱｶﾞｲﾄﾞｽﾗｲﾀﾞｰの摺動抵抗値を測定する"
],
"WorkPoints": [
"各ﾘﾆｱﾌﾞﾛｯｸに対して摺動抵抗測定を実施する※測定速... | [
{
"WorkName": "ﾘﾆｱｳｴｲ精度確認",
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolName": "ﾌｫｰｽｹﾞｰｼﾞ",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "Peak値4.5N以下Base値4.0N以下Peak-Base値1.0N以内Baseﾊﾞﾗﾂｷ1.0N以内",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C06",
"Others... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ｸﾞﾘｰｽｼﾞｮｲﾝﾄ・ｵｲﾙﾊﾟﾝ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にJOINT を取付ける",
"2. 1完成品に③をBOLT で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｳｴｲ右端で取付ける事",
"下方向に押し当て取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m",
"締付ﾄ... | [
{
"WorkName": "ｸﾞﾘｰｽｼﾞｮｲﾝﾄ・ｵｲﾙﾊﾟﾝ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①(③)に②(④)をBOLT WASHER で取付ける",
"2. 取付け後ﾍｯﾄﾞﾌﾟﾚｰﾄを動作させｵｲﾙﾊﾟﾝと干渉が無い事を確認する"
],
"WorkPoints": [
"黄色ﾏｰｶｰ",
"隙間無き事",
"ﾘﾆｱｳｴｲ右端で取付ける事",
"全ｽﾄﾛｰｸにて確認する... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "Y・Z方向変位測定",
"Words": [
"真直度 0.03mm以下",
"両端で0㎜",
"両端で0㎜",
"69mm",
"測定範囲:全ST (0.03mm以下)",
"69mm",
"この作業では同じものを2個製作",
"293㎜(振分けST94㎜)",
"387㎜(振分けST94㎜)",
"測定範囲(94㎜ST)",
"340㎜(ｾﾝﾀｰ)"
],
"WorkItem... | [
{
"WorkName": "Y・Z方向変位測定",
"QualityItem": "Z方向Y方向変位確認",
"ToolManageNo": "-",
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "全STのZ方向変位0.03㎜以下150STのZ方向変位0.01㎜以下Y方向変位(真直度)0.03㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾘﾆｱｽｹｰﾙ取付",
"Words": [
"FM",
"FM",
"FM",
"FM",
"右 端",
"中 央",
"左 端",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①(④)に②(⑤)をBOLT WASHER で取付ける",
"2. 1完成品に③(⑥)をBOLT WASHER WASHER で取付ける"
],
"WorkPoint... | [
{
"WorkName": "ﾘﾆｱｽｹｰﾙ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾘﾆｱｽｹｰﾙ配線処理",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①の配線を㉖ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"配線が穴に被ら無い事",
"配線がﾘﾆｱｽｹｰﾙに干渉してい無い事"
],
"Tolks"... | [
{
"WorkName": "ﾘﾆｱｽｹｰﾙ配線処理",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ取付",
"Words": [
"A",
"6.5㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付ける",
"2. 1完成品に③をWASHER BOLT で取付ける"
],
"WorkPoints": [
"A矢視",
"B矢視",
"BLOCK と③の上面を合わせて取付ける",
"... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ｹｰﾌﾞﾙﾗﾍﾞﾙ貼付",
"Words": [
"B312",
"B311",
"CMRR",
"CMFR",
"A矢視",
"A",
"CMFR",
"8㎜"
],
"WorkItems": [
"1. CABLE のｺﾈｸﾀｰへLABEL のﾗﾍﾞﾙを貼付ける(下図参照の事)"
],
"WorkPoints": [
"ｺﾈｸﾀｰの広い側に貼付ける事",
"F用ﾍｯ... | [
{
"WorkName": "ｹｰﾌﾞﾙﾗﾍﾞﾙ貼付",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ｹｰﾌﾞﾙﾄﾞｯｷﾝｸﾞ",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"18㎜",
"48㎜",
"85㎜"
],
"WorkItems": [
"1. ①にCABLE を㉗で取付ける"
],
"WorkPoints": [
"下記指示を参照にﾏｰｷﾝｸﾞして黄色のみ 束ねる事",
"㉗を束ねる時にコネクター... | [
{
"WorkName": "ｹｰﾌﾞﾙﾄﾞｯｷﾝｸﾞ",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線の引き回",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"A",
"5mm",
"ｽｹｰﾙﾍｯﾄﾞｹｰﾌﾞﾙ",
"ｶﾒﾗｹｰﾌﾞﾙ",
"A",
"B",
"C",
"D",
"48㎜",
"ｽｹｰﾙﾍｯﾄﾞｹｰﾌﾞﾙは内側に配置する",
"この作業では同じも... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線の引き回",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線①",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. TUBE TUBE を①のｼﾞｮｲﾝﾄに挿入する",
"2. 1完成品にBRACKET をSCREW で固定する",
"3. 2完成品を㉙で固定する"
],
"WorkPoint... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線②",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①のFANモーター線と配管を㉗で固定する",
"2. ①の配線先端部をヘッドブラケットに\u000b 這わせ㉗で固定する",
"3. 2完成品にTUBE TUBE を挿入する(左右2箇所)... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③",
"Words": [
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をBOLT で仮付ける",
"2. ﾄﾞﾛｱｰｺﾈｸﾀｰの位置調整行う"
],
"WorkPoints": [
"手順１： ①の㉗取付面に打痕キズ等無い事手順2： ①に㉗を取付ける（締付トルク：3.6N･m）\u000b手順3： グリスチュー... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線③",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②を位置合わせして仮止めﾎﾞﾙﾄを本締結する",
"3. 2完成品にSPACER を取付ける",
"2. 1完成品をBOLT WASHER ､WASHER BOLT で取付ける"
],
"WorkPoints": [
"②をﾈｼﾞ穴ｾﾝﾀｰに合わせる事",
"SPACER はBO... | [
{
"WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付",
"Words": [
"K022-2(R用)",
"K022-1(F用)"
],
"WorkItems": [
"1. ①(②)に③(④)をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾄｯﾊﾟｰがﾋﾞｰﾑに接したときにｹｰﾌﾞﾙとﾌﾞﾗｹｯﾄは1㎜以上ｽｷﾏがある事",
"ﾋﾞｰﾑとｽｷﾏ無く､面で接している事",
"F側用とR側用に注意して組立す... | [
{
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "銘板貼付③",
"Words": [
"S",
"6㎜",
"23.5㎜",
"S",
"S",
"6㎜",
"23.5㎜",
"ｼﾘｱﾙ№",
"ｼﾘｱﾙ№",
"この作業では同じものを2個製作",
"型式№ / ｼﾘｱﾙ№"
],
"WorkItems": [
"■◆5. MOTOR 保護ｶﾊﾞｰを取付ける",
"■◆2. MOTOR MOTOR に異常が無... | [
{
"WorkName": "銘板貼付③",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C06",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "固定子取付-①",
"Words": [
"ｼﾘｱﾙ№",
"S極",
"S"
],
"WorkItems": [
"■◆3. 固定子半保護ｶﾊﾞｰを右側固定子に取付ける",
"■◆2. 1完成品の固定子と可動子のGAPを確認する",
"■◆1. ①(②)の右側に③をBOLT で取付ける"
],
"WorkPoints": [
"③左右はﾈｼﾞ穴ｾﾝﾀｰで取付ける事",
"③ｼﾘｱﾙ№ﾗﾍﾞﾙを右上... | [
{
"WorkName": "固定子取付-①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "固定子取付-②",
"Words": [
"S",
"S極",
"ｼﾘｱﾙ№"
],
"WorkItems": [
"■◆1. ①(②)の左側に③をBOLT で取付ける",
"■◆2. 1完成品の固定子と可動子のGAPを確認する",
"■◆3. 固定子に保護ｶﾊﾞｰを取付ける"
],
"WorkPoints": [
"固定子同士が強烈に吸引される為､指等の挟まれに注意する事(特に緑色線部)",
"③... | [
{
"WorkName": "固定子取付-②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ｽﾄｯﾊﾟｰ(F,R)・干渉ｾﾝｻｰ(Rのみ)取付",
"Words": [
"33㎜",
"37.5㎜"
],
"WorkItems": [
"1. SCREW にNUT を挿入する",
"2. ①に1完成品とSTOPPER を取付ける",
"3. 2完成品にSENSOR をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"出代:37.5㎜を確認し取付ける事",
"... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ(F,R)・干渉ｾﾝｻｰ(Rのみ)取付",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：X軸 NPM-GH (001-054）",
"WorkName": "ﾕﾆｯﾄ銘板貼付",
"Words": [
"22㎜",
"5㎜"
],
"WorkItems": [
"2. ①②に③を貼付ける",
"1. ①②の貼付け面を脱脂する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Tool... | [
{
"WorkName": "ﾕﾆｯﾄ銘板貼付",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "次工程引き渡し用LABELの仕分け",
"Words": [
"6K302",
"7K302",
"OPT1KK311",
"OPT2KK311",
"G111R",
"G112R",
"B1231R",
"B201R",
"B1232R",
"B1233R",
"B1234R",
"B1237R",
"B1240R",
"B1241R",
"B1242R... | [
{
"WorkName": "次工程引き渡し用LABELの仕分け",
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "光ﾌｧｲﾊﾞｰｹｰﾌﾞﾙﾀｸﾞ取付",
"Words": [
"OPT2K311",
"TOCP155TOSHIBAJAPAN",
"20mm",
"*****",
"参考;ﾀｲﾒｲﾄ EVO7SP( 締付強度指示値 1.5)",
"7K302",
"OPT1K311",
"6K302",
"K002-1",
"K002-2"
],
"WorkItems": [
"1. OPTICA... | [
{
"WorkName": "光ﾌｧｲﾊﾞｰｹｰﾌﾞﾙﾀｸﾞ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "光ﾌｧｲﾊﾞｰｹｰﾌﾞﾙ束線",
"Words": [
"TOCP155TOSHIBAJAPAN",
"185㎜",
"*****",
"TOCP155TOSHIBAJAPAN",
"*****",
"ｲﾝｼｭﾛｯｸ白(100mm)",
"340㎜",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"TOCP155TOSHIBAJAPAN",... | [
{
"WorkName": "光ﾌｧｲﾊﾞｰｹｰﾌﾞﾙ束線",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各指示寸法通りﾏｰｷﾝｸﾞ、結束する事±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "ﾀｰﾐﾅﾙﾌﾞﾛｯｸ検査表ﾁｪｯｸ",
"Words": [],
"WorkItems": [
"■1. TERMINAL-BLOCK の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionItems": [
"検査表①:6.その他(1)型式･検査書ﾁｪｯｸ"
],
"InspectionNo... | [
{
"WorkName": "ﾀｰﾐﾅﾙﾌﾞﾛｯｸ検査表ﾁｪｯｸ",
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "ｻｰｼﾞｷﾗｰ、ﾊﾟﾜｰﾕﾆｯﾄ検査表ﾁｪｯｸ",
"Words": [],
"WorkItems": [
"■1. ①の型式を確認し製造番号 を 検査書に記入する",
"■1. ⑥の製造番号を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionItems": [
"検査表①:1.電源部(1)型式･検査書ﾁｪｯｸ",
... | [
{
"WorkName": "ｻｰｼﾞｷﾗｰ、ﾊﾟﾜｰﾕﾆｯﾄ検査表ﾁｪｯｸ",
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "ﾌﾞﾚｰｶｰ検査表ﾁｪｯｸ",
"Words": [
"L=55",
"正面",
"右側面",
"K006-03",
"K006-04",
"K006-02",
"K006-01"
],
"WorkItems": [
"2. 付属品を確認する",
"■1. BREAKER の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",... | [
{
"WorkName": "ﾌﾞﾚｰｶｰ検査表ﾁｪｯｸ",
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "ｽｲｯﾁﾊﾟｰﾂ検査表ﾁｪｯｸ",
"Words": [
"L=80"
],
"WorkItems": [
"2. 付属品を確認する",
"■1. SWITCH-PARTS の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号",
"付属品 3点は不要の為､廃棄",
"次工程で使用"
],
"Tolks": [],
"Ins... | [
{
"WorkName": "ｽｲｯﾁﾊﾟｰﾂ検査表ﾁｪｯｸ",
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びﾛｯﾄNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Others": "-",
"ProcessNames": [
"安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ部組立",
"Words": [
"5aV001",
"6aV001",
"1aV001",
"2aV001",
"3aV001",
"4aV001",
"EV001"
],
"WorkItems": [
"2. NOISE-FILTER にCABLE CABLE を組付ける",
"■1. NOISE-FILTER の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
]... | [
{
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ部組立",
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "ﾊｰﾈｽ準備",
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎ... | [
{
"WorkName": "ﾊｰﾈｽ準備",
"QualityItem": "ｹｰﾌﾞﾙ準備確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "ﾊｰﾈｽ引き回1",
"Words": [
"L1b/L2b/L3bX101",
"基準:1a/3a/5aF101"
],
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolP... | [
{
"WorkName": "ﾊｰﾈｽ引き回1",
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：B1工程 前準備 (001-052）",
"WorkName": "ﾊｰﾈｽ引き回2",
"Words": [
"EX101",
"基準:E5X001"
],
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsModels": [
... | [
{
"WorkName": "ﾊｰﾈｽ引き回2",
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.