input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立①",
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1"
],
"WorkItems": [
"◆1. FILTER-HOLDER にｴｱｰﾌﾞﾛｰを実施",
"◆2. 1の完成品にO-RING を挿入",
"3. 2の完成品にELEMENT を挿入"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布後､下図〇部分にOﾘﾝｸﾞを挿入",
"先端の尖ったﾋﾟﾝｾｯﾄは使用し無い事"... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾐ､埃が無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立②",
"Words": [],
"WorkItems": [
"1. MANIFOLD に油砥石をかける",
"◆2. 1の完成品にｴｱｰﾌﾞﾛｰを実施",
"3. 2の完成品にSTEEL-BALL STEEL-BALL を圧入"
],
"WorkPoints": [
"表面",
"裏面",
"加工面やﾀｯﾌﾟ穴のｺﾞﾐ､ｶｽ等を除去する",
"砥石にて表裏面の加工面やﾀｯﾌﾟ穴周辺にﾊ... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立③",
"Words": [
"A",
"B",
"10°",
"45°",
"45°"
],
"WorkItems": [
"1. ①にJOINT を取付"
],
"WorkPoints": [
"A矢視",
"B矢視",
"JOINT の取付角度に注意(下図AB矢視参照)"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立④",
"Words": [],
"WorkItems": [
"1. ①にLEVER SPACER WASHER SCREW SPRING を取付"
],
"WorkPoints": [
"LEVER の指定箇所に油砥石をかける(表裏の摺動面)",
"SPRING は①とLEVER の間に挿入",
"組立完了後､LEVER がｽﾑｰｽﾞに動作する事"
],
"Tolks": [
"締付ﾄﾙｸ 6... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立④",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立⑤",
"Words": [],
"WorkItems": [
"■1. FC16 FLOWSENSOR BOARD の型式ﾁｪｯｸ",
"2. VALVE を取付",
"■3. FC16 FLOWSENSOR BOARD をO-RING PLATE BOLT WASHER で取付"
],
"WorkPoints": [
"VALVE は付属BOLTで取付",
"治具使用箇所(治具をｾｯﾄして基板挿入時の位置... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立⑤",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立⑥",
"Words": [
"68mm"
],
"WorkItems": [
"■★1. 基板組立"
],
"WorkPoints": [
"③の取付向きに注意(下図参照)",
"ｼﾘｱﾙの若い方をNP1~8にする",
"①②内側の幅を68mmで組立"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionItems": [
... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立⑥",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立⑦",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各3",
"B",
"上の端面に合わせる",
"A",
"上の端面に合わせる",
"右の端面に合わせる"
],
"WorkItems": [
"▲1. ①にTRIM を接着"
],
"WorkPoints": [
"B矢視",
"NP1~8",
"NP9~16",
"A矢視",
"... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立⑦",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各3",
"Method": "目視",
"RecordMethod": "-",
"Others": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立⑧",
"Words": [
"ﾛｯｸあり",
"ﾛｯｸなし"
],
"WorkItems": [
"1. ①に②を挿入"
],
"WorkPoints": [
"挿入方向に注意(下図参照)",
"NP1~8とNp9~16をわかる様にしておく※後工程で間違わない為",
"ﾚﾊﾞｰを押した状態で挿入",
"②が全て挿入された状態でﾚﾊﾞｰを戻してﾛｯｸさせる事※着底していない状態ではﾚ... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ組立⑧",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管①",
"Words": [
"CN5",
"CN1",
"頭",
"線",
"ｲﾝｼｭﾛｯｸ頭の位置は下",
"板金",
"ｲﾝｼｭﾛｯｸ"
],
"WorkItems": [
"★1. ①②にCABLE を接続"
],
"WorkPoints": [
"上図はNP1~8を使用して説明していますがNP9~16も内容は同じです",
"ｲﾝｼｭﾛｯｸ... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管①",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管②",
"Words": [],
"WorkItems": [
"1. ①をBOLT WASHER で締結"
],
"WorkPoints": [
"締結時､配線やｺﾈｸﾀに注意(挟み込み､引っ張り等)",
"締結には2mmのﾎﾞｰﾙﾎﾟｲﾝﾄﾋﾞｯﾄを使用する事"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionItems": [],
"Ins... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管③",
"Words": [],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [
"GWEHD-F013-002"
],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管③",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管④",
"Words": [],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [
"GWEHD-F013-002"
],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管④",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管⑤",
"Words": [
"CN3K303"
],
"WorkItems": [
"1. ②に①CABLE を接続"
],
"WorkPoints": [
"NP9~16",
"NP9~16",
"NP1~8",
"2を接続",
"5を接続"
],
"Tolks": [],
"InspectionItems": [
"検査表①:3-2 I/Oﾎﾞ... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線・配管⑤",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立①",
"Words": [
"①端部の輪を引っ掛ける",
"ｸﾞﾘｰｽ塗布位置",
"ｸﾞﾘｰｽ溝",
"ｸﾞﾘｰｽ塗布位置 (反対側にもあり)",
"ﾋﾝｼﾞﾋﾟﾝ",
"FM-5761",
"FM-5718",
"A幅に塗布",
"A",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1",
"③の両面にｸﾞﾘｰｽ塗布のこと(ｺﾞﾏ粒/1粒) 2ヵ所",
"ｸﾞﾘ... | [
{
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立①",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Others": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀ",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立②",
"Words": [
"①の向きに注意",
"ﾋﾝｼﾞﾋﾟﾝ",
"連結部",
"※隙間0.5mmは目安寸法です※下写真では､ｽｹｰﾙにて代用しています"
],
"WorkItems": [
"1. ③に上部治具をｾｯﾄする",
"2. ②を挿入し､治具をｾｯﾄする",
"3. 2の完成品に治具㉘を取付、①を組み込む"
],
"WorkPoints": [
"②... | [
{
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立②",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5761",
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞ組立治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立③",
"Words": [
"②の取付確認箇所",
"締付けﾄﾙｸ:10cN･m"
],
"WorkItems": [
"1. ③にFILTER を取付",
"2. 1の完成品にSPRING を取付"
],
"WorkPoints": [
"精密ﾄﾞﾗｲﾊﾞｰは使用しないこと",
"SPRING の取付に異常がないか確認する",
"SPRING がﾋﾟﾝの下にあること",
... | [
{
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾅｰ組立",
"Words": [],
"WorkItems": [
"1. BLOCK に油砥石をかける",
"2. 1の完成品にBOLT COLLAR BEARING を取付"
],
"WorkPoints": [
"全面にﾊﾞﾘ､異物等無き事",
"BOLT 締付後､BEARING の回転がなめらかである事を確認"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"... | [
{
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾅｰ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｽﾌﾟﾗｲﾝ組立①",
"Words": [
"ｽﾌﾟﾗｲﾝ軸側ｼﾘｱﾙNo.記載位置",
"ｽﾌﾟﾗｲﾝ外筒側ｼﾘｱﾙNo.記載位置"
],
"WorkItems": [
"1. BALL-SPLINE のｼﾘｱﾙ番号記入"
],
"WorkPoints": [
"ｽﾌﾟﾗｲﾝ外筒",
"ｽﾌﾟﾗｲﾝ軸",
"16本のﾎﾞｰﾙｽﾌﾟﾗｲﾝをｼﾘｱﾙNo｡の若い順に並べ､軸と外筒を紐付け出来る様にしておく",
... | [
{
"WorkName": "ｽﾌﾟﾗｲﾝ組立①",
"QualityItem": "ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｽﾌﾟﾗｲﾝ組立②",
"Words": [
"㉖プレートＣ",
"2.完成品",
"㉖プレートＡ",
"㉖プレートＢ",
"㉖ブロック"
],
"WorkItems": [
"2. HOUSING の摺動面に油砥石をかける",
"1. BEARING にPIN を圧入",
"◆3. 1.完成品に2.完成品を圧入"
],
"WorkPoints": [
"下面",
"ﾋﾟ... | [
{
"WorkName": "ｽﾌﾟﾗｲﾝ組立②",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5709",
"ToolName": "ﾊｳｼﾞﾝｸﾞﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｽﾌﾟﾗｲﾝ組立③",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"溝",
"溝",
"A",
"FM-5795",
"FM-5795"
],
"WorkItems": [
"4. PACKING を治具より外し､①に挿入する",
"2. 治具にPACKING を挿入する",
"◆1. 治具にｸﾞﾘｰｽを塗布する",
"◆3. PACKING の外周にｸﾞﾘｰｽを塗布する... | [
{
"WorkName": "ｽﾌﾟﾗｲﾝ組立③",
"QualityItem": "取付確認",
"ToolManageNo": "FM-6126",
"ToolName": "Yﾊﾟｯｷﾝｽﾀﾝﾄﾞｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｽﾌﾟﾗｲﾝ組立④",
"Words": [
"ｸﾞﾘｰｽ塗布領域",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:2",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:2"
],
"WorkItems": [
"1. ②にBEARING を挿入",
"◆2. １完成品を㉗へ挿入",
"4. 3完成品へBEARING HOLDER を挿入し､PIECE SCREW で仮固定",
"3. 2完成品へ①を挿入"
],
"WorkPoint... | [
{
"WorkName": "ｽﾌﾟﾗｲﾝ組立④",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀ",
"ProcessNames": [
"作業者安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立①",
"Words": [],
"WorkItems": [
"◆1. BRACKET に油砥石をかける"
],
"WorkPoints": [
"上面",
"前面",
"後面",
"下面",
"上面",
"後面",
"前面",
"下面",
"･ｴｱｰｶﾞﾝにて研磨面のｺﾞﾐ､ｶｽ等を除去する･油砥石にて､研磨面にﾊﾞﾘ･打痕等の突起がないか確認し､ｱﾙｺｰﾙで清掃す... | [
{
"WorkName": "θ軸組立①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾐ､埃が無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立②",
"Words": [],
"WorkItems": [
"1. ①にBEARING を圧入",
"2. 1の完成品にPLATE をSCREW で取付"
],
"WorkPoints": [
"BEARING は面一まで圧入する事",
"PLATE の裏表に注意(面取りがある方が上にする)",
"治具使用ｲﾒｰｼﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
... | [
{
"WorkName": "θ軸組立②",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5724",
"ToolName": "上部ﾍﾞｱﾘﾝｸﾞ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立③",
"Words": [],
"WorkItems": [
"1. ①にPIN PIN を圧入",
"2. 1の完成品に②を挿入"
],
"WorkPoints": [
"②の挿入方向に注意(下図参照)",
"矢視",
"出代3mm",
"ﾃｰﾊﾟ側を圧入",
"PIN PIN の圧入方向に注意(下図参照)",
"圧入場所は下図参照",
"ﾉｽﾞﾙﾎﾟｼﾞｼｮﾝ(NP)配置は... | [
{
"WorkName": "θ軸組立③",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5719",
"ToolName": "Dﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立④",
"Words": [],
"WorkItems": [
"1. ①にBEARING を圧入"
],
"WorkPoints": [
"ｽﾌﾟﾗｲﾝ外筒を指で矢印方回し､引掛りがないことを確認する"
],
"Tolks": [],
"InspectionItems": [
"検査表①:ﾎﾞｰﾙｽﾌﾟﾗｲﾝΘ方向回転確認"
],
"InspectionNos": [
"GWEHD-F013-00... | [
{
"WorkName": "θ軸組立④",
"QualityItem": "取付確認",
"ToolManageNo": "FM-3237",
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "なめらかな回転である事",
"Method": "手感",
"RecordMethod": "GWEHD-F013-001",
"Others": "-",
"ProcessNames": [
"作業者... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立⑤",
"Words": [
"前面",
"後面(取付ﾀｯﾌﾟがある方)",
"ｼﾘｱﾙ",
"下面",
"OK",
"NG"
],
"WorkItems": [
"1. ①に治具を取付"
],
"WorkPoints": [
"Hｶｯﾄの向きが揃っていないと治具に取付出来ない為",
"ｽﾌﾟﾗｲﾝ外筒のｼﾘｱﾙNo.が前後面共に左向きに揃える",
"Hｶｯﾄの向... | [
{
"WorkName": "θ軸組立⑤",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5597",
"ToolName": "ﾌﾟｰﾘｰﾅｯﾄ締付治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立⑥",
"Words": [],
"WorkItems": [
"1. ①にCOLLAR PULLEY COLLAR COLLAR BEARING NUT をPos1,3,7,10,14,16に取付"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"COLLAR COLLAR の方向に注意(下図参照)",
"NUT は締結しない"
],
"Tolks": [],
"Ins... | [
{
"WorkName": "θ軸組立⑥",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立⑦",
"Words": [],
"WorkItems": [
"1. ①にCOLLAR BEARING COLLAR PULLEY COLLAR NUT をPos2,6,8,9,11,15に取付"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"NUT は締結しない",
"COLLAR の方向に注意(下図参照)"
],
"Tolks": [],
"InspectionI... | [
{
"WorkName": "θ軸組立⑦",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立⑧",
"Words": [],
"WorkItems": [
"1. ①にCOLLAR PULLEY COLLAR COLLAR NUT をPos4,13に取付"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"NUT は締結しない",
"COLLAR COLLAR の方向に注意(下図参照)"
],
"Tolks": [],
"InspectionItems": [],... | [
{
"WorkName": "θ軸組立⑧",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立⑨",
"Words": [],
"WorkItems": [
"1. ①にCOLLAR COLLAR PULLEY COLLAR NUT をPos5,12に取付"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"NUT は締結しない",
"COLLAR COLLAR の方向に注意(下図参照)"
],
"Tolks": [],
"InspectionItems": [],... | [
{
"WorkName": "θ軸組立⑨",
"QualityItem": "取付確認",
"ToolManageNo": "FM-3030",
"ToolName": "ｽﾌﾟﾗｲﾝ締付けｱﾀｯﾁﾒﾝﾄ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｺﾝﾍﾞｱ･配線等の干渉無い事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸ﾌﾟｰﾘ組立",
"Words": [
"接着剤塗布 米粒:各1"
],
"WorkItems": [
"▲1. PULLEY に接着剤を塗布",
"2. 1の完成品にCOLLAR COLLAR を圧入"
],
"WorkPoints": [
"COLLAR COLLAR の圧入方向に注意(下図参照)",
"COLLAR COLLAR を確実に着底させる事(下図参照)",
"余分な接着剤は除去する事",
... | [
{
"WorkName": "θ軸ﾌﾟｰﾘ組立",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ﾛｯｸﾀｲﾄ638",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾍﾞﾙﾄ取付",
"Words": [],
"WorkItems": [
"1. ①にT-BELT を引き回す",
"2. 1の完成品に②BEARING を取付"
],
"WorkPoints": [
"ﾍﾞﾙﾄの印字が上下逆さまにならない様にする事",
"上段のﾍﾞﾙﾄを指示通りに引き回す",
"下段のﾍﾞﾙﾄを指示通りに引き回す"
],
"Tolks": [],
"InspectionItems": []... | [
{
"WorkName": "ﾍﾞﾙﾄ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
},
{
"Wor... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾅｰ取付",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT BOLT WASHER で取付け"
],
"WorkPoints": [
"矢視",
"取付場所は下図参照",
"仮止め､ﾃﾝｼｮﾝも緩めにする",
"ﾃﾝｼｮﾅｰ取付後､治具FM-5597より製品を取外す※ﾃﾝｼｮﾝは緩めの状態"
],
"Tolks": [],
"InspectionItems"... | [
{
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾅｰ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θﾌﾟｰﾘ部ｷﾞﾔ取付",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆2. GEAR ｷﾞﾔにｸﾞﾘｰｽを塗布",
"1. ①にGEAR をSHAFT で締結"
],
"WorkPoints": [
"ﾌﾟｰﾘｰの反対側から-ﾄﾞﾗｲﾊﾞｰで回り止めを行いながらSHAFT を締結する",
"指示箇所全周均一に塗布する事"
],
"Tolks": [
... | [
{
"WorkName": "θﾌﾟｰﾘ部ｷﾞﾔ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｾﾝｻｰｷﾞｱ部組立",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:1"
],
"WorkItems": [
"▲1. GEAR にBEARING をSCREW で締結"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"SCREW にﾛｯｸﾀｲﾄを塗布して締結",
"SCREW にﾛｯｸﾀｲﾄを塗布する量は3本合計でｺﾞﾏ粒1のこと",
"締結後､余分な接着剤は拭き取ること"
... | [
{
"WorkName": "ｾﾝｻｰｷﾞｱ部組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整",
"Words": [
"張力計の設定M(ﾍﾞﾙﾄ質量):1.3g/mW(ﾍﾞﾙﾄ幅) :6mmS(ｽﾊﾟﾝ) :25.62mm感度設定 :High Mode",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ調整最大値≦19N最小値≧9N12N≦平均値≦16N"
],
"WorkItems": [
"1. ①のΘ駆動ﾍﾞﾙﾄﾃﾝｼｮﾝの調整を行う"
],
"WorkPoints": [
"測定箇所は下図●にて測定",... | [
{
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整",
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolName": "ﾍﾞﾙﾄ張力計",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "最大値≦19N最小値≧9N12≦平均値≦16",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "GWEHD-F013-001",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｾﾝｻｰｷﾞﾔ取付",
"Words": [
"ｼﾘｱﾙNo",
"ｸﾞﾘｰｽ塗布 米粒:各1",
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"2. ①にGEAR をCOLLAR BOLT WASHER で締結",
"◆3. GEAR の全周にｸﾞﾘｰｽを塗布する",
"◆1. COLLAR の油溝面にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"GEAR ... | [
{
"WorkName": "ｾﾝｻｰｷﾞﾔ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｾﾝｻｰ取付",
"Words": [],
"WorkItems": [
"1. ①にSENSOR(165MM) SENSOR(80MM) をBOLT WASHER WASHER で締結"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"◆作業者安... | [
{
"WorkName": "ｾﾝｻｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θﾓｰﾀ取付①",
"Words": [
"面一",
"1mm"
],
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"指示通りに取付(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "θﾓｰﾀ取付①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θﾓｰﾀ取付②",
"Words": [],
"WorkItems": [
"■1. ①にMOTOR をWASHER ⑰で仮固定"
],
"WorkPoints": [
"Θ1軸(1~4)(9~12)",
"Θ2軸(5~8)(13~16)",
"矢視",
"仮止め:SD-A0035434-048にて本締め"
],
"Tolks": [],
"InspectionItems": [
"検査表①:Θ軸ﾓ... | [
{
"WorkName": "θﾓｰﾀ取付②",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θﾓｰﾀ取付③",
"Words": [
"ﾌﾟｰﾘｰ側",
"CN15K301",
"CN14K301",
"CN3K301",
"CN2K301",
"Θ1軸ﾓｰﾀ",
"Θ2軸ﾓｰﾀ",
"40mm",
"18mm",
"CN15K301",
"CN14K301"
],
"WorkItems": [
"1. ①のﾓｰﾀを締結",
"2.COUPLI... | [
{
"WorkName": "θﾓｰﾀ取付③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立⑩",
"Words": [
"摺動方向",
"ﾃｰﾊﾟ側",
"ｸﾞﾘｰｽ塗布 小豆:1",
"転がり面",
"摺動面",
"転がり面",
"摺動面",
"C 面取り",
"②④は手締めで仮固定を行う",
"仮止め:SD-A035434-050にて本締め",
"C 面取り"
],
"WorkItems": [
"◆1. PLATE にｸﾞﾘｰｽを塗布",... | [
{
"WorkName": "θ軸組立⑩",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆粒:各1",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立⑪",
"Words": [
"整定板:3本",
"ﾌﾟﾚｰﾄ:4本",
"整定板",
"整定板"
],
"WorkItems": [
"1. ①に②を挿入",
"5. 整定板を押す",
"6.整定板とﾌﾟﾚｰﾄを本締めする",
"4. ５秒以上待ち、㉛の０点合わせを行う",
"7. ㉙㉛㉜ 取り外す",
"8. ｽﾌﾟﾗｲﾝｼｬﾌﾄの摺動を確認する",
"3. ㉛... | [
{
"WorkName": "θ軸組立⑪",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸組立⑫",
"Words": [],
"WorkItems": [
"◆1. SPRING の両端にｸﾞﾘｰｽ塗布",
"2. 1の完成品とCOLLAR COLLAR BEARING を①に挿入し､NUT WASHER で締結"
],
"WorkPoints": [
"COLLAR の挿入方向に注意(下図参照)",
"内径が大きい方をｼｬﾌﾄ側に挿入する"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m... | [
{
"WorkName": "θ軸組立⑫",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ・Z軸連結",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"◆1. ②の連結部にｸﾞﾘｰｽ塗布",
"2. 1の完成品と①をBOLT WASHER で締結"
],
"WorkPoints": [
"指示箇所に塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionItems": [],
"Inspec... | [
{
"WorkName": "θ・Z軸連結",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸ﾓｰﾀｰ原点調整治具接続",
"Words": [
"電源ｹｰﾌﾞﾙ接続",
"PCｹｰﾌﾞﾙ(USB)",
"電源ｽｲｯﾁ",
"PCｹｰﾌﾞﾙ(USB)",
"治具ｹｰﾌﾞﾙ(ﾓｰﾀ接続)"
],
"WorkItems": [
"1. ﾓｰﾀに治具を接続する"
],
"WorkPoints": [
"PCｹｰﾌﾞﾙのUSBはPCに接続する",
"【注意】 電源ｽｲｯﾁOFF状態を確認... | [
{
"WorkName": "θ軸ﾓｰﾀｰ原点調整治具接続",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5747",
"ToolName": "θ軸原点確認ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ軸ﾓｰﾀｰ原点調整原点出し操作方法",
"Words": [],
"WorkItems": [
"1. PCのPANATERMを起動する",
"2. PANATERM画面になってから､電源SWを【ON】し､電源を供給する",
"4. 【その他を】ｸﾘｯｸする",
"5. 青枠の【Z相ｻｰﾁ】をｸﾘｯｸすると画面が切替わる",
"6. 【ｻｰﾎﾞｵﾝ】をｸﾘｯｸする",
"7. 【Z相ｻｰﾁを】ｸﾘｯｸする",
"3.... | [
{
"WorkName": "θ軸ﾓｰﾀｰ原点調整原点出し操作方法",
"QualityItem": "操作方法",
"ToolManageNo": "FM-5747",
"ToolName": "θ軸原点確認ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"Words": [
"1本に3箇所",
"〇穴",
"回転",
"この位置にする"
],
"WorkItems": [
"1. ﾉｽﾞﾙ角度調整を行う"
],
"WorkPoints": [
"①ﾎﾙﾀﾞのｾｯﾄﾋﾞｽを緩めてﾎﾙﾀﾞが回転出来る状態にする(16本全て)",
"②ｾﾝｻｰ部ｷﾞｱの〇穴をｾﾝｻｰ投光部分にくる様にｷﾞｱを回転させる(左右2箇所)",
... | [
{
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ位相合わせ",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5689",
"ToolName": "ﾉｽﾞﾙ角度調整治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "JOINT取付",
"Words": [],
"WorkItems": [
"1. ①にJOINT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"◆作業者安全作業"
],
"ToolPartsModels": [
... | [
{
"WorkName": "JOINT取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾉｽﾞﾙｶﾞｰﾄﾞ、ﾀｲﾏｳﾝﾄ取付",
"Words": [],
"WorkItems": [
"1. ①にCLIP をBOLT で取付",
"2. PLATE をSPACER BOLT WASHER で取付"
],
"WorkPoints": [
"CLIP の取付方向に注意(下図参照)",
"PLATE は下方向に押付けながら取付",
"CLIP PLATE 取付位置(下図参照･左右共通)",
"PLATE 取... | [
{
"WorkName": "ﾉｽﾞﾙｶﾞｰﾄﾞ、ﾀｲﾏｳﾝﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "連結ﾌﾞﾗｹｯﾄ取付",
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1",
"ｼｯｸﾈｽ挿入部分",
"ﾌﾞﾗｹｯﾄを矢印の方向に押付けながら締結する"
],
"WorkItems": [
"◆1. BRACKET の指定箇所にｸﾞﾘｰｽ塗布",
"2. 1の完成品を①にBOLT で取付"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布",
"ｸﾘｱﾗﾝｽ0.1mmになる様にｼｯｸﾈｽ... | [
{
"WorkName": "連結ﾌﾞﾗｹｯﾄ取付",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "補強ﾌﾞﾗｹｯﾄ取付",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各2"
],
"WorkItems": [
"▲1. PLATE にTRIM TRIM を接着",
"2. 1の完成品とPLATE をSPACER SCREW BOLT WASHER BOLT WASHER で取付"
],
"WorkPoints": [
"SCREW はﾓｰﾀｰ側に底付きさせる(目安7mm)"
],
"Tolks": [
... | [
{
"WorkName": "補強ﾌﾞﾗｹｯﾄ取付",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ配線",
"Words": [
"細線",
"太線",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾁｭｰﾌﾞ端面より7mm",
"ﾁｭｰﾌﾞ端面より10mm"
],
"WorkItems": [
"1. ﾄﾞﾛｱｺﾈｸﾀの配線をJOINTに固定"
],
"WorkPoints": [
"固定場所に注意(右図... | [
{
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ配線",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾗﾐﾀﾓｰﾀ部配線",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN27/28",
"CN27/28",
"結束",
"結束",
"青ﾏｰｶで文字を塗りつぶす",
"青ﾏｰｶで文字を塗りつぶす",
"結束"
],
"WorkItems": [
"1. FANｹｰﾌﾞﾙをﾌﾞﾗｹｯﾄに固定",... | [
{
"WorkName": "ﾗﾐﾀﾓｰﾀ部配線",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ取付(前側NP1~8)",
"Words": [],
"WorkItems": [
"1. ①に⑥BRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"⑥BRACKET は共締め",
"上図は説明の為､配線･配管は省略しています",
"⑥BRACKET 締結時､傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"Inspec... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ取付(前側NP1~8)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ取付(後側NP9~16)",
"Words": [
"ﾌｫﾄｾﾝｻ配線CN2K303",
"ﾊﾞﾙﾌﾞ用配線は手前",
"IO通信配線は奥"
],
"WorkItems": [
"1. ①に⑥BRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"以下のｺﾈｸﾀはﾏﾆﾎｰﾙﾄﾞ取付後では作業が困難な為､ﾏﾆﾎｰﾙﾄﾞ取付時に作業し易い状態で接続する事",
"⑥B... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ取付(後側NP9~16)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線①(前側NP1~8)",
"Words": [
"B8 B7 B6 B5",
"V8 V7 V6 V5",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"収縮ﾁｭｰﾌﾞの端面で結束",
"収縮ﾁｭｰﾌﾞの端面で結束",
"ｲﾝｼｭﾛｯｸ結束方向",
"ｲﾝｼｭﾛｯｸ結束方向",
"ｲﾝｼｭﾛｯｸ結束方向",
"ｲ... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線①(前側NP1~8)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線①(後側NP9~16)",
"Words": [
"B9 B10 B11 B12",
"V9 V10 V11 V12",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"収縮ﾁｭｰﾌﾞの端面で結束",
"ｲﾝｼｭﾛｯｸ結束方向",
"収縮ﾁｭｰﾌﾞの端面で結束",
"ｲﾝｼｭﾛｯｸ結束方向",
"ｲﾝｼｭﾛｯｸ結束方向... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線①(後側NP9~16)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｼﾘｺﾝﾁｭｰﾌﾞ取付",
"Words": [],
"WorkItems": [
"1. ①にTUBE(70MM CUT) を取付"
],
"WorkPoints": [
"ﾁｭｰﾌﾞ取付後ﾉｽﾞﾙ上昇確認を行う",
"TUBE(70MM CUT) に折れ､よじれ等無き事",
"TUBE(70MM CUT) は各JOINTに確実に挿入する事"
],
"Tolks": [],
"InspectionItems": [
... | [
{
"WorkName": "ｼﾘｺﾝﾁｭｰﾌﾞ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-001",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線②(前側NP1~8)",
"Words": [
"CN1K302",
"CN3K302",
"CN2K302",
"後側ﾏﾆﾎｰﾙﾄﾞより",
"Θ1原点ｾﾝｻ"
],
"WorkItems": [
"1. ①の前側IO基板にｺﾈｸﾀを接続"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [
"検査表①:IOﾎﾞ... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線②(前側NP1~8)",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"特殊工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "配管接続(白配管)",
"Words": [
"①白色335mm",
"④白色320mm",
"⑥白色235mm",
"③白色240mm",
"Pos1~8側",
"Pos9~16側",
"ﾍﾞｰｽﾌﾟﾚｰﾄをくぐらせてﾄﾞﾛｱｺﾈｸﾀ方面へ",
"ﾍﾞｰｽﾌﾟﾚｰﾄをくぐらせてﾄﾞﾛｱｺﾈｸﾀ方面へ※黄色配管も同様"
],
"WorkItems": [
"1. ①に②を接続"
],
... | [
{
"WorkName": "配管接続(白配管)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾁｬｰﾄﾏｰｸLED用配線固定",
"Words": [
"ﾁｬｰﾄﾏｰｸLED用配線",
"くぐらせる",
"くぐらせる",
"ｺﾈｸﾀ先端から70mm位置でﾀｲﾏｳﾝﾄにｾﾝｻｹｰﾌﾞﾙと一緒に結束する",
"70mm",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"矢視",
"結束",
"結束",
"結束",
... | [
{
"WorkName": "ﾁｬｰﾄﾏｰｸLED用配線固定",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線②(後側NP9~16)",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白配管",
"ﾁｬｰﾄﾏｰｸ",
"ﾊﾞﾙﾌﾞｹｰﾌﾞﾙ",
"白配管",
"黄配管",
"ﾊﾞﾙﾌﾞｹｰﾌﾞﾙB9~B12",
"ﾁｬｰﾄﾏｰｸ",
"ﾊﾞﾙﾌﾞｹｰﾌﾞﾙB13~B16",
"Θ2ｾﾝｻｹ... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線②(後側NP9~16)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "θ2軸側面配線",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"IO基板間通信線",
"ﾊﾞﾙﾌﾞｹｰﾌﾞﾙ",
"白配管",
"ﾊﾞﾙﾌﾞｹｰﾌﾞﾙ",
"白配管",
"IO基板間通信線"
],
"WorkItems": [
"1. 指示箇所を結束"
],
"WorkPoints": [],... | [
{
"WorkName": "θ2軸側面配線",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線③(前側NP1~8)",
"Words": [
"21mm",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白配管",
"ﾊﾞﾙﾌﾞｹｰﾌﾞﾙ",
"IO基板間通信線",
"黄配管",
"IO基板間通信線",
"白配管",
"ﾊﾞﾙﾌﾞｹｰﾌﾞﾙB5~B8",
"白配管",
"ﾊﾞﾙﾌﾞｹｰ... | [
{
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ配線③(前側NP1~8)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理①",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"IO通信線",
"白配管",
"Zﾓｰﾀ動力線",
"結束",
"ｲﾝｼｭﾛｯｸ下から入れる※頭の位置注意!",
"結束",
"右側も同様",
"結束",
"結束"
],
"WorkItems": [
"... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理②",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白配管",
"Zﾓｰﾀ動力線",
"仮結束"
],
"WorkItems": [
"1. 指示箇所を結束"
],
"WorkPoints": [
"IO通信線は一緒に結束しない",
"仮結束箇所はﾒｲﾝ基板取付後に結束する",
... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理③",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白配管",
"IO通信線",
"仮結束",
"Θﾓｰﾀ動力線",
"Θﾓｰﾀｴﾝｺｰﾀﾞ線"
],
"WorkItems": [
"1. 指示箇所を結束"
],
"WorkPoints": [
"仮結束箇所はﾒｲﾝ基板取付... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理③",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理④",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"FAN配線",
"IO通信線",
"IO通信線",
"仮結束",
"仮結束",
"白配管"
],
"WorkItems": [
"1. 指示箇所を結束"
],
"WorkPoints": [
"仮結束箇所はﾒｲﾝ... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理④",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理⑤",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"結束",
"白配管",
"黄配管",
"Zﾓｰﾀ動力線"
],
"WorkItems": [
"1. 指示箇所を結束"
],
"WorkPoints": [
"ﾗﾐﾀﾓｰﾀｹｰﾌﾞﾙにｽﾄﾚｽが無い様にする事"
],
"... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理⑤",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理⑥",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白配管",
"Zﾓｰﾀ動力線",
"仮結束",
"CN3K301",
"CN2K301",
"CN1"
],
"WorkItems": [
"1. 指示箇所を結束"
],
"WorkPoints": [
"黄配管... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理⑥",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理⑦",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白配管",
"仮結束",
"Θﾓｰﾀ動力線",
"Θﾓｰﾀｴﾝｺｰﾀﾞ線",
"FAN配線",
"CN3K301",
"CN2K301"
],
"WorkItems": [
"1. 指示箇所を結束"
],
"Wo... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理⑦",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理⑧",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"FAN配線",
"ﾍｯﾄﾞ通信線(白ｺﾈｸﾀ)",
"仮結束",
"仮結束",
"ﾍｯﾄﾞ通信線(白ｺﾈｸﾀ)",
"FANｹｰﾌﾞﾙ",
"CN28"
],
"WorkItems": [
"1. 指示箇所を結束"
]... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理⑧",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付前処理⑨",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"仮結束",
"ﾍｯﾄﾞ通信線(白ｺﾈｸﾀ)",
"CN6"
],
"WorkItems": [
"1. 指示箇所を結束"
],
"WorkPoints": [
"仮結束箇所はﾒｲﾝ基板取付後に結束する",
"ｲﾝｼｭﾛｯｸ頭位置に注... | [
{
"WorkName": "ﾒｲﾝ基板取付前処理⑨",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付",
"Words": [],
"WorkItems": [
"2. ①にSCREW を取付",
"■★1. FC16 MAIN BOARD の型式･ｼﾘｱﾙNo.確認",
"■★3. 1の完成品にFC16 MAIN BOARD をSPACER で締結"
],
"WorkPoints": [
"手締めで底付きにする(出代約5mm)",
"基板取付時､配線を挟まない様に注意",
"基板向きに注意(下図参照... | [
{
"WorkName": "ﾒｲﾝ基板取付",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板接続",
"Words": [
"ﾗﾐﾀﾓｰﾀｹｰﾌﾞﾙZ軸ｴﾝｺｰﾀﾞ"
],
"WorkItems": [
"★1. ﾒｲﾝ基板に各ｺﾈｸﾀを接続"
],
"WorkPoints": [
"各ｺﾈｸﾀ部のｹｰﾌﾞﾙ引っ張りに注意",
"ﾗﾐﾀﾓｰﾀｹｰﾌﾞﾙにｽﾄﾚｽが無い様にする事※特にｺﾈｸﾀ部のｹｰﾌﾞﾙの引っ張り等に注意",
"ﾗﾐﾀﾓｰﾀｹｰﾌﾞﾙにｽﾄﾚｽが無い様にする事※特にｺﾈｸﾀ部のｹｰﾌ... | [
{
"WorkName": "ﾒｲﾝ基板接続",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWEHD-F013-002",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付後処理①",
"Words": [
"白配管",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"仮結束済⇒結束",
"Θ1軸ｴﾝｺｰﾀﾞ線",
"Θ1軸ｴﾝｺｰﾀﾞ線",
"FAN配線",
"仮結束済⇒結束",
"仮結束済⇒結束",
"仮結束済⇒結束"
],
"WorkItems": [
"★1... | [
{
"WorkName": "ﾒｲﾝ基板取付後処理①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付後処理②",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"Θ2軸ｴﾝｺｰﾀﾞ線",
"白配管",
"48V電源線",
"仮結束済⇒結束",
"仮結束済⇒結束",
"仮結束済⇒結束",
"仮結束済⇒結束"
],
"WorkItems": [
"★1. ﾒｲﾝ基板周辺の整線を行う"
... | [
{
"WorkName": "ﾒｲﾝ基板取付後処理②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付後処理③",
"Words": [],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ.26",
"ToolName... | [
{
"WorkName": "ﾒｲﾝ基板取付後処理③",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付後処理④",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾗﾐﾀﾓｰﾀ動力ﾞ線",
"白配管",
"白配管"
],
"WorkItems": [
"1. ﾒｲﾝ基板周辺の整線を行う"
],
"WorkPoints": [
"無理な引っぱり等無き事"
],
"Tolks": [],
... | [
{
"WorkName": "ﾒｲﾝ基板取付後処理④",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾒｲﾝ基板取付後処理⑤",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白配管",
"ﾗﾐﾀﾓｰﾀ動力ﾞ線",
"ﾁｬｰﾄﾏｰｸLED用配ﾞ線",
"黄配管",
"白配管",
"ﾁｬｰﾄﾏｰｸLED用配ﾞ線",
"黄配管"
],
"WorkItems": [
"1. ﾒｲﾝ基板周辺の整線を行う"... | [
{
"WorkName": "ﾒｲﾝ基板取付後処理⑤",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾄﾞﾛｱ部配管接続",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"黄配管",
"ﾁｬｰﾄﾏｰｸLED用配ﾞ線"
],
"WorkItems": [
"1. ①にJOINT を接続",
"2. ｶﾌﾟﾗあそび確認"
],
"WorkPoints": [
"無理な引っぱり等無き事",
"配管の折れが無き事... | [
{
"WorkName": "ﾄﾞﾛｱ部配管接続",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "上下左右10N以下で動く事",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "GWEHD-F013-001",
"Others": "-",
"ProcessNames... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "左側面上部整線",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"白配管",
"ﾍｯﾄﾞ通信線",
"黄配管",
"FG線",
"白配管",
"ﾍｯﾄﾞ通信線",
"黄配管",
"FG線",
"ﾍｯﾄﾞ通信線"
],
"WorkItems": [
"■1. ①にSCREW を締... | [
{
"WorkName": "左側面上部整線",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "上面ｶﾊﾞｰﾗﾍﾞﾙ貼付け",
"Words": [],
"WorkItems": [
"■2. COVER にLABEL を貼付け",
"■1. COVER にLABEL LABEL を貼付け"
],
"WorkPoints": [
"COVER LABEL の向きに注意(下図参照)",
"COVER LABEL LABEL の向きに注意(下図参照)"
],
"Tolks": [],
"InspectionItems... | [
{
"WorkName": "上面ｶﾊﾞｰﾗﾍﾞﾙ貼付け",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "前面ｶﾊﾞｰ取付",
"Words": [],
"WorkItems": [
"■1. ②に③を⑯⑰で締結",
"■2. 1の完成品を①に④で締結"
],
"WorkPoints": [
"ｶﾊﾞｰ取付後､ｶﾊﾞｰと配線の干渉が無いか確認"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"InspectionItems": [
"検査表①:ﾈｼ... | [
{
"WorkName": "前面ｶﾊﾞｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "上面ｶﾊﾞｰ取付",
"Words": [],
"WorkItems": [
"1. ①に②をSCREW で締結"
],
"WorkPoints": [
"ｶﾊﾞｰ取付後､ｶﾊﾞｰと配線の干渉が無いか確認",
"②の取付方向に注意(下図参照)※説明の為､ﾊﾝﾄﾞﾙは非表示にしてます"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionItems": [],
"Inspec... | [
{
"WorkName": "上面ｶﾊﾞｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ｻｲﾄﾞｶﾊﾞｰ取付",
"Words": [],
"WorkItems": [
"1. ①にCOVER COVER をSCREW で締結"
],
"WorkPoints": [
"Θ1軸用",
"Θ2軸用"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"... | [
{
"WorkName": "ｻｲﾄﾞｶﾊﾞｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾁｬｰﾄﾏｰｸ取付①",
"Words": [],
"WorkItems": [
"1. ①にBRACKET BRACKET をBOLT WASHER で締結"
],
"WorkPoints": [
"BRACKET BRACKET の取付方向に注意(下図参照)",
"説明の為､一部非表示にしています"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
... | [
{
"WorkName": "ﾁｬｰﾄﾏｰｸ取付①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "ﾁｬｰﾄﾏｰｸ取付②",
"Words": [
"ｺﾈｸﾀ",
"穴(大)"
],
"WorkItems": [
"2. ﾏｰｸｷｯﾄｺﾈｸﾀ接続",
"■1. ①にLED-LAMP-UNIT をBOLT WASHER で締結"
],
"WorkPoints": [
"説明の為､一部非表示にしています",
"LED-LAMP-UNIT の取付方向に注意(下図参照)"
],
"Tolks": [
... | [
{
"WorkName": "ﾁｬｰﾄﾏｰｸ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "製造ﾗﾍﾞﾙ貼付け",
"Words": [
"32mm",
"1mm"
],
"WorkItems": [
"1. ①に⑥を貼付け"
],
"WorkPoints": [
"⑥の向きに注意(下図参照)"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"T... | [
{
"WorkName": "製造ﾗﾍﾞﾙ貼付け",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH： FC16 HEAD UNIT（001-097）",
"WorkName": "付属品払い出し",
"Words": [
"合わせて払い出す"
],
"WorkItems": [
"1. ①と付属品CLAMP-ARM SPRING FILTER TUBE(70MM CUT) を一緒に払い出す"
],
"WorkPoints": [
"付属品はﾊﾟｯｷﾝｸﾞして､ﾍｯﾄﾞ完成品と合わせて払い出す"
],
"Tolks": [],
"InspectionItems": [],
"Inspection... | [
{
"WorkName": "付属品払い出し",
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した付属品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査1‐①",
"Words": [],
"WorkItems": [
"1. ﾍｯﾄﾞ取付",
"2. ﾁｪｯｶとﾍｯﾄﾞ取付けの隙間を確認",
"3. 制御BOXの電源をONする"
],
"WorkPoints": [
"背面4箇所固定",
"0.1mm以下",
"0.1mm以下"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [
"検... | [
{
"WorkName": "検査1‐①",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けできている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査1‐②",
"Words": [],
"WorkItems": [
"1. ﾍｯﾄﾞ取付",
"2. ﾁｪｯｶとﾍｯﾄﾞ取付けの隙間を確認",
"3. 制御BOXの電源をONする"
],
"WorkPoints": [
"背面4箇所固定",
"0.1mm以下"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [
"検査表①FC16:19.ﾍｯﾄﾞﾁ... | [
{
"WorkName": "検査1‐②",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けできている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査2",
"Words": [],
"WorkItems": [
"1. ﾁｪｯｶｿﾌﾄを起動",
"2. 検査員を設定し[OK]を押す",
"3. 検査員ﾓｰﾄﾞを押す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"Ji... | [
{
"WorkName": "検査2",
"QualityItem": "画面確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査3",
"Words": [],
"WorkItems": [
"1. 真空ﾎﾟﾝﾌﾟがOFFしていることを確認し[OK]を押す",
"2. ﾉｽﾞﾙﾁｪﾝｼﾞｬにﾉｽﾞﾙがあることを確認し[OK]を押す"
],
"WorkPoints": [
"FC03はﾉｽﾞﾙﾁｪﾝｼﾞｬ確認は無し"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": ... | [
{
"WorkName": "検査3",
"QualityItem": "画面確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査4",
"Words": [],
"WorkItems": [
"1. [取付完了]を押す",
"2. 真空ﾎﾟﾝﾌﾟの電源をONし､[OK]を押す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ... | [
{
"WorkName": "検査4",
"QualityItem": "画面確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査5",
"Words": [],
"WorkItems": [
"1. ﾍｯﾄﾞの2次元ｺｰﾄﾞをｽｷｬﾝする",
"2. ｽｷｬﾝした情報が読み込まれたら､[OK]を押す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguN... | [
{
"WorkName": "検査5",
"QualityItem": "画面確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査6",
"Words": [],
"WorkItems": [
"1. [検査開始]を押す",
"2. ﾁｬｰﾄﾏｰｸの点灯を確認し､[OK]を押す"
],
"WorkPoints": [
"検査が自動で開始される",
"ﾁｬｰﾄﾏｰｸの点灯確認は､FC16のみ"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"... | [
{
"WorkName": "検査6",
"QualityItem": "画面確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査7(FC03のみ)",
"Words": [],
"WorkItems": [
"1. 下記ﾒｯｾｰｼﾞが表示されたら､ｶﾊﾞｰを開け､穴無しﾉｽﾞﾙを取付",
"2. ｶﾊﾞｰを閉じ､[取付完了]を押す"
],
"WorkPoints": [
"3本取付",
"ﾉｽﾞﾙ穴無し"
],
"Tolks": [],
"InspectionItems": [
"検査表①:ﾍｯﾄﾞﾁｪｯｶｰ確認"
],
"Inspecti... | [
{
"WorkName": "検査7(FC03のみ)",
"QualityItem": "画面確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "FCヘッドチェッカ確認（FCヘッド共通）",
"WorkName": "検査8(FC03のみ)",
"Words": [],
"WorkItems": [
"1. 下記ﾒｯｾｰｼﾞが表示されたら､ｶﾊﾞｰを開け､穴有りﾉｽﾞﾙを取付",
"2. ｶﾊﾞｰを閉じ､[取付完了]を押す"
],
"WorkPoints": [
"3本取付",
"ﾉｽﾞﾙ穴有り"
],
"Tolks": [],
"InspectionItems": [
"検査表①:ﾍｯﾄﾞﾁｪｯｶｰ確認"
],
"Inspecti... | [
{
"WorkName": "検査8(FC03のみ)",
"QualityItem": "画面確認",
"ToolManageNo": "FM-5712",
"ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.