input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(補給NG排出部) NPM-G Serirs (001-030）",
"WorkName": "補給部組立1",
"Words": [],
"WorkItems": [
"2. 1完成品にGUIDE をSPACER BOLT WASHER で仮取付けする",
"1. BRACKET にBRACKET BRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"取付け方向",
"取付け方向",
"ﾌﾞﾗｹｯﾄ同士の端面を合わせる事",
... | [
{
"WorkName": "補給部組立1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(補給NG排出部) NPM-G Serirs (001-030）",
"WorkName": "補給部組立2",
"Words": [],
"WorkItems": [
"1. ①にBRACKET BRACKET をBOLT WASHER で取付ける",
"2. 1完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],
"Inspec... | [
{
"WorkName": "補給部組立2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(補給NG排出部) NPM-G Serirs (001-030）",
"WorkName": "補給部組立3",
"Words": [],
"WorkItems": [
"1. ①にSTOPPER をBOLT NUT で取付ける"
],
"WorkPoints": [
"矢印方向に当付けて取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"Wor... | [
{
"WorkName": "補給部組立3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(補給NG排出部) NPM-G Serirs (001-030）",
"WorkName": "補給完了SW組立",
"Words": [],
"WorkItems": [
"1. SWITCH の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. BRACKET にSWITCH を取付ける"
],
"WorkPoints": [
"BRACKET の突起とSWITCH の窪みを合わせ取付ける事",
"三角ﾏｰｸ",
"三角ﾏｰｸ",
"この部分の型式を確... | [
{
"WorkName": "補給完了SW組立",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C32",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(補給NG排出部) NPM-G Serirs (001-030）",
"WorkName": "ﾏｸﾞﾈｯﾄ組立",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"1. BRACKET にMAGNET をBOLT で取付ける",
"2. MAGNET をBRACKET にNUT-PLATE BOLT で取付ける",
"◆3. 2完成品にPLATE SPACER をBOLT WASHER NUT で取付ける"
],
"WorkPoints"... | [
{
"WorkName": "ﾏｸﾞﾈｯﾄ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(補給NG排出部) NPM-G Serirs (001-030）",
"WorkName": "補給ﾄﾞｱSW組立",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"2. 1完成品をPLATE にNUT-PLATE BOLT WASHER WASHER で取付ける",
"3. 2完成品にCABLE-SUPPORT を取付け配線を固定する",
"4. 3完成品に⑤を... | [
{
"WorkName": "補給ﾄﾞｱSW組立",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C32",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
},... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(補給NG排出部) NPM-G Serirs (001-030）",
"WorkName": "左ﾌﾚｰﾑ組立",
"Words": [],
"WorkItems": [
"1. BRACKET にSPACER をBOLT WASHER で取付ける",
"2. 1完成品に③をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾍﾟｰｻｰ取付け方向"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 194cN･m"... | [
{
"WorkName": "左ﾌﾚｰﾑ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(補給NG排出部) NPM-G Serirs (001-030）",
"WorkName": "右ﾌﾚｰﾑ組立",
"Words": [],
"WorkItems": [
"1. BRACKET にBRACKET BRACKET をBOLT WASHER で取付ける",
"2. 1完成品にWASHER BOLT ･SPACER を取付ける",
"3. 2完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1... | [
{
"WorkName": "右ﾌﾚｰﾑ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立①",
"Words": [
"座ｸﾞﾘ面有り",
"座ｸﾞﾘ面無し"
],
"WorkItems": [
"1. PLATE へCAM-FOLLOWER をSPACER NUT で取付ける",
"2. 1の完成品へCOLLAR BOLT を取付ける",
"3. 2の完成品へCOLLAR WASHER BOLT NUT を取付ける"
],
"WorkPoint... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立②",
"Words": [
"座ｸﾞﾘ面有り",
"座ｸﾞﾘ面無し"
],
"WorkItems": [
"1. PLATE へCAM-FOLLOWER をSPACER NUT で取付ける",
"2. 1の完成品へCOLLAR BOLT を取付ける",
"3. 2の完成品へCOLLAR WASHER BOLT NUT を取付ける"
],
"WorkPoint... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左右】引込みｱｰﾑ部組立③",
"Words": [
"OR",
"OR"
],
"WorkItems": [
"1. SHAFT へBEARING (ORBEARING )を挿入後､E-RING を挿入する"
],
"WorkPoints": [
"この作業では同じものを2個製作"
],
"Tolks": [],
"InspectionItems": [],
"In... | [
{
"WorkName": "【左右】引込みｱｰﾑ部組立③",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立④",
"Words": [
"出代:4mm",
"ﾘﾆｱﾌﾞﾛｯｸ基準面(線引きﾏｰｸ)",
"ｸﾞﾘｰｽ塗布 米粒:3"
],
"WorkItems": [
"◆3. 2の完成品(リニアレール)に㉜を塗布する",
"1. LEVER へPIN を圧入する",
"2. 1の完成品へLINEAR-WAY をBOLT で取付ける"
],
"WorkPo... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立④",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "圧入台",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立⑤",
"Words": [
"出代:4mm",
"ﾘﾆｱﾌﾞﾛｯｸ基準面(線引きﾏｰｸ)",
"ｸﾞﾘｰｽ塗布 米粒:3"
],
"WorkItems": [
"1. LEVER にPIN を圧入する",
"◆3. 2の完成品(リニアレール)に㉜を塗布する",
"2. 1の完成品へLINEAR-WAY をBOLT で取付ける"
],
"WorkPo... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立⑤",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "圧入台",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立⑥",
"Words": [
"②の付属品(ﾅｯﾄ)",
"②の付属品(ﾅｯﾄ)"
],
"WorkItems": [
"1. PLATE へCAM-FOLLOWER SPACER をCAM-FOLLOWER の付属品(ﾅｯﾄ)で取付ける",
"2. 1の完成品へCOLLAR BOLT を取付ける"
],
"WorkPoints": [
"CAM-FOLLOW... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立⑥",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立⑦",
"Words": [
"②の付属品(ﾅｯﾄ)",
"②の付属品(ﾅｯﾄ)"
],
"WorkItems": [
"1. PLATE へCAM-FOLLOWER SPACER をCAM-FOLLOWER の付属品(ﾅｯﾄ)で取付ける",
"2. 1の完成品へCOLLAR BOLT を取付ける"
],
"WorkPoints": [
"CAM-FOLLOW... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立⑦",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左右】引込みｱｰﾑ部組立⑧",
"Words": [
"この作業では同じものを2個製作",
"OR",
"OR"
],
"WorkItems": [
"1. FRANGE へCOLLAR BEARING (ORBEARING )SHAFT をWASHER BOLT で仮取付けする"
],
"WorkPoints": [
"BOLT はSD-A040901-019/SD-A04090... | [
{
"WorkName": "【左右】引込みｱｰﾑ部組立⑧",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立⑨",
"Words": [
"面を合わせる"
],
"WorkItems": [
"1. ①へ②をWASHER BOLT で取付ける"
],
"WorkPoints": [
"②の取付方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionN... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立⑨",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立⑩",
"Words": [
"面を合わせる"
],
"WorkItems": [
"1. ①へ②をWASHER BOLT で取付ける"
],
"WorkPoints": [
"②の取付方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionN... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立⑩",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立⑪",
"Words": [
"外周",
"ｸﾞﾘｰｽ塗布 小豆:4",
"ｽﾌﾟﾘﾝｸﾞ挿入穴",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1",
"外周",
"ｸﾞﾘｰｽ塗布 小豆:4",
"押さえる",
"押さえる",
"内周",
"ｽﾌﾟﾘﾝｸﾞ先端",
"ｸﾞﾘｰｽ塗布 小豆:4"
],
"WorkItems": ... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立⑪",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立⑫",
"Words": [
"外周",
"ｸﾞﾘｰｽ塗布 小豆:4",
"ｽﾌﾟﾘﾝｸﾞ挿入穴",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1",
"外周",
"ｸﾞﾘｰｽ塗布 小豆:4",
"押さえる",
"内周",
"ｸﾞﾘｰｽ塗布 小豆:4",
"ｽﾌﾟﾘﾝｸﾞ先端",
"押さえる"
],
"WorkItems": ... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立⑫",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立⑬",
"Words": [
"出代:4mm",
"押し当て"
],
"WorkItems": [
"1. BRACKET へ砥石を掛け､PIN を圧入する",
"2. 1の完成品へDOG をWASHER BOLT で取付ける",
"3. 2の完成品へCAM をBOLT で取付ける"
],
"WorkPoints": [
"赤塗りに砥石を掛ける事",... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立⑬",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立⑭",
"Words": [
"出代:4mm"
],
"WorkItems": [
"1. BRACKET へ砥石を掛け､PIN を圧入する",
"2. 1の完成品へCAM をBOLT で取付ける"
],
"WorkPoints": [
"赤塗り部に砥石を掛ける事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"In... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立⑭",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "加工面に打痕､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立⑮",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:2"
],
"WorkItems": [
"1. ①へ②をBOLT BOLT で取付ける",
"◆2. 1の完成品へ㉘を塗布する"
],
"WorkPoints": [
"BOLT の挿入先に注意する事",
"溝ｶﾑ内面に塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立⑮",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立⑯",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:2"
],
"WorkItems": [
"1. ①へ②をBOLT で取付ける",
"◆2. 1の完成品へ㉘を塗布する"
],
"WorkPoints": [
"溝ｶﾑ内面に塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立⑯",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立⑰",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"◆1. ①へ②をBOLT で固定し、㉚を塗布する"
],
"WorkPoints": [
"定盤との隙間にｼｯｸﾈｽｹﾞｰｼﾞが通らないこと",
"定盤上で面を合わせる",
"長穴内面へ塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ ... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立⑰",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立⑱",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"◆1. ①へ②をBOLT で固定し、㉚を塗布する"
],
"WorkPoints": [
"定盤上で面を合わせる",
"定盤との隙間にｼｯｸﾈｽｹﾞｰｼﾞが通らないこと",
"長穴内面へ塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ ... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立⑱",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立⑲",
"Words": [
"外周",
"ｸﾞﾘｰｽ塗布 小豆:3",
"内周",
"ｸﾞﾘｰｽ塗布 小豆:3",
"外周､先端",
"ｸﾞﾘｰｽ塗布 小豆:3",
"締付ﾄﾙｸ 3.2N･m"
],
"WorkItems": [
"◆1. ①へSPRING ③を挿入し､BOLT WASHER で取付ける"
],
"WorkPo... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立⑲",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立⑳",
"Words": [
"外周､先端",
"外周",
"ｸﾞﾘｰｽ塗布 小豆:3",
"内周",
"ｸﾞﾘｰｽ塗布 小豆:3",
"ｸﾞﾘｰｽ塗布 小豆:3",
"締付ﾄﾙｸ 3.2N･m"
],
"WorkItems": [
"◆1. ①へSPRING ③を挿入し､BOLT WASHER で取付ける"
],
"WorkPo... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立⑳",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】引込みｱｰﾑ部組立㉑",
"Words": [],
"WorkItems": [
"1. ①へ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾌﾟﾘﾝｸﾞ先端をｶﾗｰの外側にかける事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "【左】引込みｱｰﾑ部組立㉑",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立㉒",
"Words": [],
"WorkItems": [
"1. ①へ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾌﾟﾘﾝｸﾞ先端をｶﾗｰの外側にかける事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立㉒",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】引込みｱｰﾑ部組立㉓",
"Words": [],
"WorkItems": [
"1. ①へDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾚﾊﾞｰと面合わせの事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"Wor... | [
{
"WorkName": "【右】引込みｱｰﾑ部組立㉓",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾓｰﾀ駆動部組立①",
"Words": [
"ﾃｰﾊﾟ部を内側へ向ける事",
"OR"
],
"WorkItems": [
"1. BLOCK へPULLEY BEARING COLLAR をLOCK-NUT で取付ける",
"2. 1の完成品へWASHER BEARING (ORBEARING )をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [... | [
{
"WorkName": "ﾓｰﾀ駆動部組立①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾓｰﾀ駆動部組立②",
"Words": [
"②と隙間無い事",
"仮止め:SD-A041086-443にて本締め"
],
"WorkItems": [
"1. ①へPULLEY をBOLT で取付ける"
],
"WorkPoints": [
"ｽﾊﾟﾅをかけたHｶｯﾄ部分にﾊﾞﾘが発生し､ﾌﾟｰﾘｰの回転が悪くなる事があるので､ｻﾝﾄﾞﾍﾟｰﾊﾟｰやﾔｽﾘでﾊﾞﾘを取り､ﾌﾟｰﾘｰがｽﾑｰ... | [
{
"WorkName": "ﾓｰﾀ駆動部組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾓｰﾀ駆動部組立③",
"Words": [
"OR"
],
"WorkItems": [
"1. PLATE へWASHER BEARING (ORBEARING )をBOLT で取付ける"
],
"WorkPoints": [
"取付け面に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionItems": [],
... | [
{
"WorkName": "ﾓｰﾀ駆動部組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾓｰﾀ駆動部組立④",
"Words": [
"1.8mm",
"ﾓｰﾀとﾌﾟｰﾘの隙間;1.8mm",
"隙間無い事",
"②と③のｽﾘｯﾄを合わせる事",
"ﾃｰﾊﾟ面",
"ﾃｰﾊﾟ面"
],
"WorkItems": [
"■1. MOTOR へLOCK PULLEY をBOLT で取付ける",
"2. PLATE へ1の完成品をBOLT で取付ける"
... | [
{
"WorkName": "ﾓｰﾀ駆動部組立④",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C34",
"Others": "-",
"ProcessNames": [
"安全工程"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾓｰﾀ駆動部組立⑤",
"Words": [],
"WorkItems": [
"1. ①へ②をBOLT WASHER で仮取付けする",
"2. 1の完成品へ③をBOLT WASHER で仮取付けする"
],
"WorkPoints": [
"SD-A040901-059で本締め",
"SD-A040901-060で本締め"
],
"Tolks": [],
"Inspection... | [
{
"WorkName": "ﾓｰﾀ駆動部組立⑤",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【前】ﾌﾟｰﾘ組立①",
"Words": [
"OR",
"OR"
],
"WorkItems": [
"1. BLOCK へCOLLAR BEARING (ORBEARING )PULLEY COLLAR をBOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"In... | [
{
"WorkName": "【前】ﾌﾟｰﾘ組立①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【前】ﾌﾟｰﾘ組立②",
"Words": [],
"WorkItems": [
"3. 2の完成品へBOLT をNUT でﾛｯｸする",
"1. BLOCK へSPACER STOPPER をBOLT WASHER で取付ける",
"2. ④へ1の完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [
"面合わせ",
"BOLT は④へ当付ける事"
],... | [
{
"WorkName": "【前】ﾌﾟｰﾘ組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【後】ﾌﾟｰﾘ組立",
"Words": [
"OR",
"OR"
],
"WorkItems": [
"1. BLOCK へCOLLAR をBOLT WASHER NUT で取付ける",
"2. 1の完成品へCOLLAR BEARING (ORBEARING )PULLEY COLLAR をBOLT NUT WASHER WASHER で取付ける"
],
"WorkPoints": [],
... | [
{
"WorkName": "【後】ﾌﾟｰﾘ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ｽﾄｯﾊﾟｰ組立",
"Words": [],
"WorkItems": [
"1. SPACER へSPACER STOPPER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "O/Rｾﾝｻ組立",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET へSENSOR をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionItems": [],
"InspectionNo... | [
{
"WorkName": "O/Rｾﾝｻ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾊﾟﾚｯﾄ引き出確認、有無ｾﾝｻ組立",
"Words": [
"2.8mm",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET へSENSOR をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionItems": [],
"In... | [
{
"WorkName": "ﾊﾟﾚｯﾄ引き出確認、有無ｾﾝｻ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "TL軸ｲﾝﾀｰﾛｯｸｾﾝｻ組立",
"Words": [
"押し付け"
],
"WorkItems": [
"1. BRACKET へSENSOR をNUT-PLATE BOLT WASHER WASHER で取付ける",
"2. BRACKET へ1の完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [
"長穴ｾﾝﾀｰで締結する事"
],
"Tolk... | [
{
"WorkName": "TL軸ｲﾝﾀｰﾛｯｸｾﾝｻ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻﾌﾞﾗｹｯﾄ組立",
"Words": [
"上面面合わせ",
"左右丸穴ｾﾝﾀｰ"
],
"WorkItems": [
"1. BRACKET へBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"丸穴ｾﾝﾀｰで締結する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
... | [
{
"WorkName": "【左】TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻﾌﾞﾗｹｯﾄ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Pr... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻﾌﾞﾗｹｯﾄ組立",
"Words": [
"上面面合わせ",
"左右丸穴ｾﾝﾀｰ"
],
"WorkItems": [
"1. BRACKET へBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"丸穴ｾﾝﾀｰで締結する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
... | [
{
"WorkName": "【右】TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻﾌﾞﾗｹｯﾄ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Pr... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【中央】ｶﾞｲﾄﾞ部組立",
"Words": [
"傾斜あり"
],
"WorkItems": [
"1. COVER へGUIDE SPACER をSCREW で取付ける"
],
"WorkPoints": [
"GUIDE の取付け方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionItems": [],
"... | [
{
"WorkName": "【中央】ｶﾞｲﾄﾞ部組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】ｶﾞｲﾄﾞ部組立①",
"Words": [
"10mm"
],
"WorkItems": [
"1. BRACKET へGUIDE SPACER をBOLT WASHER で仮取付けする",
"2. 1の完成品へBOLT NUT を仮取付けする"
],
"WorkPoints": [
"SD-A040901-073で本締め",
"SD-A040901-068で本締め"
... | [
{
"WorkName": "【左】ｶﾞｲﾄﾞ部組立①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】ｶﾞｲﾄﾞ部組立②",
"Words": [],
"WorkItems": [
"1. ①へCLIP をBOLT で取付ける",
"2. 1の完成品へ④をBOLT WASHER で取付ける"
],
"WorkPoints": [
"CLIP の取付け方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 194cN･m"
],
... | [
{
"WorkName": "【左】ｶﾞｲﾄﾞ部組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】ｶﾞｲﾄﾞ部組立③",
"Words": [
"2.0mm"
],
"WorkItems": [
"1. ①へ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"T=0.5±0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [
"検査表①:引き出部ﾊﾟﾚｯﾄ有無... | [
{
"WorkName": "【左】ｶﾞｲﾄﾞ部組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】ｶﾞｲﾄﾞ部組立①",
"Words": [
"10mm"
],
"WorkItems": [
"1. BRACKET へGUIDE SPACER をBOLT WASHER で仮取付けする",
"2. 1の完成品へBOLT NUT を仮取付けする"
],
"WorkPoints": [
"SD-A040901-068で本締め",
"SD-A040901-073で本締め"
... | [
{
"WorkName": "【右】ｶﾞｲﾄﾞ部組立①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】ｶﾞｲﾄﾞ部組立②",
"Words": [],
"WorkItems": [
"1. ①へCLIP をBOLT で取付ける",
"2. 1の完成品へ④をBOLT WASHER で取付ける"
],
"WorkPoints": [
"CLIP の取付け方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 194cN･m"
],
... | [
{
"WorkName": "【右】ｶﾞｲﾄﾞ部組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立①",
"Words": [
"出代:2mm",
"2mm"
],
"WorkItems": [
"1. PLATE へSPRING-PIN を圧入する",
"2. 1の完成品へCLIP をBOLT で取付ける"
],
"WorkPoints": [
"表面へ挿入する事",
"裏面へ取付けする事",
"CLIP の取付け方向に注意"
]... | [
{
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "圧入台",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立②",
"Words": [],
"WorkItems": [
"1. ①へBLOCK BLOCK をBOLT WASHER で取付ける"
],
"WorkPoints": [
"丸穴ｾﾝﾀｰで取付ける事",
"①のﾌﾟﾚｰﾄからはみ出さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],... | [
{
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "傾斜ｶﾑ仮取付",
"Words": [
"③仮止め:SD-A040901-047にて本締め",
"前側"
],
"WorkItems": [
"1. ①へCAM CAM をBOLT WASHER BOLT WASHER で仮取付けする",
"2. 1の完成品を㉗へ取付ける"
],
"WorkPoints": [
"CAM 仮止め:SD-A040901-050にて本締め",
... | [
{
"WorkName": "傾斜ｶﾑ仮取付",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】傾斜ｶﾑ調整",
"Words": [
"1mm",
"傾斜ｶﾑ(右)",
"傾斜ｶﾑ(右)",
"前側",
"前側",
"後側"
],
"WorkItems": [
"1. ①の傾斜ｶﾑ(右)位置調整をする"
],
"WorkPoints": [
"S-PINと傾斜ｶﾑに隙間無い事"
],
"Tolks": [
"締付ﾄﾙｸ... | [
{
"WorkName": "【右】傾斜ｶﾑ調整",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【右】ﾘﾆｱｶﾞｲﾄﾞ取付",
"Words": [
"測定面",
"押し付け",
"押し付け",
"ｽﾗｲﾄﾞﾌﾞﾛｯｸ基準面(線引きﾏｰｸ)",
"ﾚｰﾙ基準面"
],
"WorkItems": [
"1. ①へLINEAR-WAY をBOLT で取付ける"
],
"WorkPoints": [
"右側LMｶﾞｲﾄﾞ平行度;0.02㎜以下",
"ｽﾗ... | [
{
"WorkName": "【右】ﾘﾆｱｶﾞｲﾄﾞ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】ﾘﾆｱｶﾞｲﾄﾞ取付",
"Words": [
"測定面",
"押し付け",
"押し付け",
"ﾚｰﾙ基準面"
],
"WorkItems": [
"1. ①へLINEAR-WAY をBOLT で取付ける"
],
"WorkPoints": [
"ｽﾗｲﾄﾞﾌﾞﾛｯｸ基準面(線引きﾏｰｸ)",
"ｽﾗｲﾄﾞﾌﾞﾛｯｸの脱落に注意する事",
"左側L... | [
{
"WorkName": "【左】ﾘﾆｱｶﾞｲﾄﾞ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左】傾斜ｶﾑ調整",
"Words": [
"1mm",
"測定面",
"傾斜ｶﾑ(左)",
"前側",
"後側"
],
"WorkItems": [
"1. ①の傾斜ｶﾑ(左)位置調整をする"
],
"WorkPoints": [
"ｽﾗｲﾄﾞﾌﾞﾛｯｸの脱落に注意する事",
"左側傾斜ｶﾑ平行度;0.02㎜以下"
],
"Tolks":... | [
{
"WorkName": "【左】傾斜ｶﾑ調整",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "引込みｱｰﾑ部取付",
"Words": [
"正面図",
"前側"
],
"WorkItems": [
"1. ①へ②③をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾗｲﾄﾞﾌﾞﾛｯｸの脱落に注意する事",
"ｽﾗｲﾄﾞﾌﾞﾛｯｸとｱｰﾑﾌﾞﾛｯｸに隙間無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
... | [
{
"WorkName": "引込みｱｰﾑ部取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "CLIP(表面)取付",
"Words": [
"前側"
],
"WorkItems": [
"1. ①へCLIP をBOLT で取付ける"
],
"WorkPoints": [
"CLIP の取付け方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionItems": [],
"InspectionNos": [],... | [
{
"WorkName": "CLIP(表面)取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "引込みｱｰﾑ部連結①",
"Words": [
"前側"
],
"WorkItems": [
"1. ①へSHAFT を③で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業... | [
{
"WorkName": "引込みｱｰﾑ部連結①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "引込みｱｰﾑ部連結②",
"Words": [],
"WorkItems": [
"1. PLATE へBLOCK をBOLT WASHER で取付ける",
"2. ③へ1の完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionItem... | [
{
"WorkName": "引込みｱｰﾑ部連結②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【前】ﾌﾟｰﾘ取付",
"Words": [
"面合わせ"
],
"WorkItems": [
"1. ①へ②をBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [... | [
{
"WorkName": "【前】ﾌﾟｰﾘ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【後】ﾌﾟｰﾘ取付",
"Words": [],
"WorkItems": [
"1. ①へ②をBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
... | [
{
"WorkName": "【後】ﾌﾟｰﾘ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"Words": [
"前側"
],
"WorkItems": [
"1. ①へ②をWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾓｰﾀ駆動部取付",
"Words": [],
"WorkItems": [
"1. ①へ②をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
... | [
{
"WorkName": "ﾓｰﾀ駆動部取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "T-BELT取付・調整①",
"Words": [
"断面図",
"測定箇所",
"調整後締結"
],
"WorkItems": [
"1. ①へT-BELT を取付ける"
],
"WorkPoints": [
"74N±10%",
"質量:2.5g/m幅:15㎜ｽﾊﾟﾝ:280㎜",
"軸を動作させ数回測定する事"
],
"Tolks": [
... | [
{
"WorkName": "T-BELT取付・調整①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "T-BELT取付・調整②",
"Words": [
"断面図",
"調整後締結"
],
"WorkItems": [
"1. ①へT-BELT を取付ける"
],
"WorkPoints": [
"44N±10%",
"質量:2.5g/m幅:9㎜ｽﾊﾟﾝ:68㎜",
"軸を動作させ数回測定する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m... | [
{
"WorkName": "T-BELT取付・調整②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "引込みｱｰﾑとT-BELT連結",
"Words": [
"前側",
"前側"
],
"WorkItems": [
"2. 引き出ｱｰﾑとT-BELTをBOLT WASHER で連結する",
"1. ①のT-BELTへPLATE BLOCK をBOLT で取付ける"
],
"WorkPoints": [
"PLATE の凸とT-BELTの凹を合わせる事",
"作業1で取付け... | [
{
"WorkName": "引込みｱｰﾑとT-BELT連結",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "O/Rｾﾝｻ取付",
"Words": [
"前側"
],
"WorkItems": [
"1. ①へ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"長穴ｾﾝﾀｰで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "O/Rｾﾝｻ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "TL軸ｲﾝﾀｰﾛｯｸｾﾝｻ取付",
"Words": [
"前側",
"後側"
],
"WorkItems": [
"1. ①へ②をBOLT WASHER で取付ける",
"2. 1の完成品へSTAY STAND BRACKET をBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [
"ﾍﾞｰｽﾌﾟﾚｰﾄと端面を合わせる事"
],
"Tol... | [
{
"WorkName": "TL軸ｲﾝﾀｰﾛｯｸｾﾝｻ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "配線引き回し①",
"Words": [
"B1322R",
"B1323R",
"B1324R"
],
"WorkItems": [
"1. ①へCABLE を接続する"
],
"WorkPoints": [
"接続されている事"
],
"Tolks": [],
"InspectionItems": [
"検査表①:ｺﾈｸﾀ挿入確認"
],
... | [
{
"WorkName": "配線引き回し①",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C34",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "配線引き回し②",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"前側"
],
"WorkItems": [
"1. ①へ配線を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [... | [
{
"WorkName": "配線引き回し②",
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "配線引き回し③",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"後側"
],
"WorkItems": [
"1. ①へ配線を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [... | [
{
"WorkName": "配線引き回し③",
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ｶﾞｲﾄﾞ部仮取付",
"Words": [
"前面",
"後面"
],
"WorkItems": [
"1. ①へ②③をBOLT WASHER で仮取付けする"
],
"WorkPoints": [
"①の傾斜ｶﾑ背面と②③の背面を合わせる",
"SD-A040901-068で本締め"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "ｶﾞｲﾄﾞ部仮取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ｶﾞｲﾄﾞ部高さ調整",
"Words": [
"基準面",
"測定箇所",
"測定箇所",
"測定箇所",
"測定箇所",
"166.2mm"
],
"WorkItems": [
"1. ①のｶﾞｲﾄﾞﾌﾞﾗｹｯﾄ高さを調整する"
],
"WorkPoints": [
"ｱｼﾞｬｽﾄﾎﾞﾙﾄにて調整後ﾅｯﾄをﾛｯｸする事",
"166.2+0... | [
{
"WorkName": "ｶﾞｲﾄﾞ部高さ調整",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻｰ取付",
"Words": [
"受光",
"投光",
"受光",
"投光"
],
"WorkItems": [
"2. ①へSENSOR をSCREW WASHER WASHER で取付ける",
"■1. 型式確認､ﾛｯﾄ番号記入"
],
"WorkPoints": [
"配線引き回しは下から①と㉖の間を通す事"
]... | [
{
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻｰ取付",
"QualityItem": "型式･ﾛｯﾄ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C34",
"Others": "-",
"ProcessNames": [
"安... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "配線引き回し④",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"右側面",
"前下面",
"受光",
"受光",
"投光"
],
"WorkItems": [
"1. ①へ配線を引き回す"
],
"WorkPoints": [],
"Tolks": [],
... | [
{
"WorkName": "配線引き回し④",
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "配線引き回し⑤",
"Words": [
"投光",
"B1303R",
"B1304R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"左側面"
],
"WorkItems": [
"1. ①へCABLE を引き回す"
],
"WorkPoints": [
"挿入されている事"
... | [
{
"WorkName": "配線引き回し⑤",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C34",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "配線引き回し⑥",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"150mm",
"投光",
"受光",
"下面"
],
"WorkItems": [
"1. ①へ配線を引き回す"
],
"WorkPoints": [
"稼働部に干渉無い事"
],
"To... | [
{
"WorkName": "配線引き回し⑥",
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "WEPJ-G002-C34",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整",
"Words": [
"ｶﾞｲﾄﾞ押し当て",
"ｶﾞｲﾄﾞ押し当て"
],
"WorkItems": [
"1. ①のﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅を調整する"
],
"WorkPoints": [
"ガイドと㉙に隙間無い事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],... | [
{
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【左右】ﾊﾟﾚｯﾄｶﾞｲﾄﾞ隙間確認",
"Words": [],
"WorkItems": [
"1. ①のﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度を確認する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"隙間がある場合は再調整:SD-A040901-068参照"
],
"Tolks": [],
"InspectionItems": [
"検査表①:ﾊﾟﾚｯ... | [
{
"WorkName": "【左右】ﾊﾟﾚｯﾄｶﾞｲﾄﾞ隙間確認",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5242",
"ToolName": "ｶﾞｲﾄﾞ幅調整ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C34",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "【中央】ﾊﾟﾚｯﾄｶﾞｲﾄﾞ取付",
"Words": [],
"WorkItems": [
"1. ①へ②をWASHER BOLT で取付ける"
],
"WorkPoints": [
"通り:0.1㎜/止まり:0.15㎜",
"規格値に入らない場合は再調整:SD-A040901-068参照"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"Inspecti... | [
{
"WorkName": "【中央】ﾊﾟﾚｯﾄｶﾞｲﾄﾞ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(引き出部) NPM-G Serirs (001-076）",
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻ光軸調整",
"Words": [
"投光",
"受光",
"光軸",
"ｽﾄｯﾊﾟｰ",
"ﾌﾞﾛｯｸ",
"光軸",
"ﾚﾊﾞｰの穴を通過する事"
],
"WorkItems": [
"1. ①へ㉖をセットする",
"2. ｾﾝｻの光軸を調整する",
"3. 引き出部を組立台から取り外す"
],
... | [
{
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻ光軸調整",
"QualityItem": "光軸確認",
"ToolManageNo": "-",
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞﾌﾞﾗｹｯﾄ組立",
"Words": [
"空間容積の30%~40%"
],
"WorkItems": [
"2. BRACKET の切削面全てを油砥石でﾊﾞﾘ､打ｺﾝ確認をおこなう",
"3. 1完成品を製品品番面合わせにして2完成品に挿入する",
"4. 3完成品にPLATE をBOLT WASHER で取付ける",
"◆1. BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝにｸﾞﾘｰｽを塗... | [
{
"WorkName": "ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞﾌﾞﾗｹｯﾄ組立",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の30~40%",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞﾌﾞﾗｹｯﾄにﾒｶｽﾄ取付",
"Words": [],
"WorkItems": [
"1. ①にSTOPPER COLLAR SPACER をBOLT で取付ける(2ヵ所)"
],
"WorkPoints": [
"STOPPER COLLAR SPACER の順番に注意し取付ける",
"組立順番に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
... | [
{
"WorkName": "ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞﾌﾞﾗｹｯﾄにﾒｶｽﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proce... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "上部ﾌﾟﾚｰﾄにﾒｶｽﾄ取付",
"Words": [],
"WorkItems": [
"1. PLATE の切削面全てを油砥石でﾊﾞﾘ､打ｺﾝ確認をおこなう",
"2. PLATE にSTOPPER SPACER をBOLT で取付ける(2ヵ所)"
],
"WorkPoints": [
"完成品",
"組立順番､向きに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
... | [
{
"WorkName": "上部ﾌﾟﾚｰﾄにﾒｶｽﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "基準側ﾌﾚｰﾑにﾋﾟﾝ圧入",
"Words": [],
"WorkItems": [
"1. FRAME の切削面全てを油砥石でﾊﾞﾘ､打ｺﾝ確認をおこなう",
"2. 1完成品にPIN PIN を圧入する"
],
"WorkPoints": [
"出代:3㎜",
"出代:5㎜",
"PIN PIN の出代に注意する事"
],
"Tolks": [],
"InspectionItems"... | [
{
"WorkName": "基準側ﾌﾚｰﾑにﾋﾟﾝ圧入",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "基準側ﾌﾚｰﾑと従動側ﾌﾚｰﾑ仮付け",
"Words": [],
"WorkItems": [
"1. FRAME の切削面全てを油砥石でﾊﾞﾘ､打ｺﾝ確認をおこなう",
"2. 1完成品に①②③をBOLT で仮付けする"
],
"WorkPoints": [
"･向きに注意する事･定盤上で作業する事",
"ﾀｯﾌﾟが上",
"完成品",
"M4ﾀｯﾌﾟが上"
],
"Tolks":... | [
{
"WorkName": "基準側ﾌﾚｰﾑと従動側ﾌﾚｰﾑ仮付け",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "定盤",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "ﾌﾚｰﾑ直角度確認",
"Words": [],
"WorkItems": [
"1. ①を直角ﾏｽﾀｰと定盤に当付け下記写真部に隙間が無いよう仮固定する"
],
"WorkPoints": [
"定盤",
"定盤",
"定盤",
"定盤",
"定盤",
"直角ﾏｽﾀｰ",
"直角ﾏｽﾀｰ",
"隙間:0.01㎜以下",
"隙間:0.01㎜以下",
... | [
{
"WorkName": "ﾌﾚｰﾑ直角度確認",
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "ﾌﾚｰﾑ平面度確認、直角度再確認",
"Words": [],
"WorkItems": [
"1. ①に再度㉗に取付て定盤に当付けながら、各固定ボルトを増し締めする"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞ0.01㎜が通ら無い事",
"隙間:0.01㎜以下",
"隙間:0.01㎜以下",
"面合わせ",
"①と治具の隙間:0.01㎜以下",
"ﾘﾌﾄﾌﾚｰﾑ組立ｼ... | [
{
"WorkName": "ﾌﾚｰﾑ平面度確認、直角度再確認",
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEMA-G002-001",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "LMｶﾞｲﾄﾞ取付前準備",
"Words": [],
"WorkItems": [
"1. LINEAR-WAY のLMｶﾞｲﾄﾞの型式確認とｼﾘｱﾙNo.記録を行う",
"2. 1完成品の開梱時の油分拭き取り、㉖でバリ、打コン等無いことを確認する"
],
"WorkPoints": [
"隙間:0.01㎜以下",
"･検査表の型式HSR15R2UUC1E+1060L-Ⅱと入荷時の型式が一致することを確認する事･ｼ... | [
{
"WorkName": "LMｶﾞｲﾄﾞ取付前準備",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEMA-G002-001",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "LMｶﾞｲﾄﾞ仮付け",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT で仮付けする"
],
"WorkPoints": [
"①のﾋﾟﾝ",
"基準面が内内になる事",
"Ser№刻印位置",
"Ser№刻印位置",
"基準面",
"･取付け面のﾊﾞﾘ､打ｺﾝ確認をする事･②の仮付け方向に注意する"
],
"Tolks": [],
... | [
{
"WorkName": "LMｶﾞｲﾄﾞ仮付け",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "LMｶﾞｲﾄﾞ基準側ﾘﾆｱ組立",
"Words": [],
"WorkItems": [
"2. TUBE を右記寸法にｶｯﾄする",
"3. 2完成品をJOINT に取付ける",
"4. 3完成品を1完成品(ﾘﾆｱ)に取付ける",
"1. ①ＬＭガイドのリニアを㉖治具を使用しレールから取り外す"
],
"WorkPoints": [
"90㎜:1本 105㎜:1本",
"90㎜:左ﾘﾆｱ",
... | [
{
"WorkName": "LMｶﾞｲﾄﾞ基準側ﾘﾆｱ組立",
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6001",
"ToolName": "ﾘﾆｱｶﾞｲﾄﾞ取り外し治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "LMｶﾞｲﾄﾞ基準側真直度調整",
"Words": [],
"WorkItems": [
"1. ①LMｶﾞｲﾄﾞの基準側ﾚｰﾙの真直度の調整を行う",
"2. ②LMｶﾞｲﾄﾞのﾘﾆｱを①の基準がﾚｰﾙに挿入する"
],
"WorkPoints": [
"真直度:0.02㎜以下",
"LMｶﾞｲﾄﾞとﾋﾟﾝの隙間:0.01㎜以下の事(ﾋﾟﾝ基準)",
"左端まで測定する",
"ﾋﾟﾝ基準",
... | [
{
"WorkName": "LMｶﾞｲﾄﾞ基準側真直度調整",
"QualityItem": "真直度確認",
"ToolManageNo": "-",
"ToolName": "ｽﾄﾚｰﾄｴｯｼﾞ",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "真直度:0.02㎜以下",
"Method": "ｽﾄﾚｰﾄｴｯｼﾞ",
"RecordMethod": "WEMA-G002-001",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "LMｶﾞｲﾄﾞ従動側ﾘﾆｱ組立",
"Words": [],
"WorkItems": [
"3. 2完成品をJOINT に取付ける",
"4. 3完成品を1完成品(ﾘﾆｱ)に取付ける",
"2. TUBE を右記寸法にｶｯﾄする",
"1. ①ＬＭガイドのリニアを㉖治具を使用しレールから取り外す"
],
"WorkPoints": [
"90㎜:1本 105㎜:1本",
"90㎜:左ﾘﾆｱ",
... | [
{
"WorkName": "LMｶﾞｲﾄﾞ従動側ﾘﾆｱ組立",
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6001",
"ToolName": "ﾘﾆｱｶﾞｲﾄﾞ取り外し治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "LMｶﾞｲﾄﾞ従動側平行度調整",
"Words": [],
"WorkItems": [
"2. ②LMｶﾞｲﾄﾞのﾘﾆｱを①の従動側ﾚｰﾙに挿入する",
"1. ①LMｶﾞｲﾄﾞの従動側ﾚｰﾙの平行度の調整を行う"
],
"WorkPoints": [
"平行度:0.02㎜以下",
"ここ基準で平行調整する事",
"LMｶﾞｲﾄﾞ基準側と従動側のﾋﾟｯﾁ165㎜を基準で平行調整する事",
"測... | [
{
"WorkName": "LMｶﾞｲﾄﾞ従動側平行度調整",
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolName": "ｽﾄﾚｰﾄｴｯｼﾞ",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "平行度:0.02㎜以下",
"Method": "ｽﾄﾚｰﾄｴｯｼﾞ",
"RecordMethod": "WEMA-G002-001",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "ﾌﾚｰﾑにｾﾝｻｰとFT4取付け",
"Words": [],
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付ける(7ｶ所)",
"2. 1完成品にSENSOR をBOLT WASHER WASHER で取付ける(2ヵ所)"
],
"WorkPoints": [
"CABLE-SUPPORT 取付場所と向きに注意する事",
"7ｶ所全て上下の向きでCABLE-SUPPORT 取付ける",... | [
{
"WorkName": "ﾌﾚｰﾑにｾﾝｻｰとFT4取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "ﾎﾞｰﾙﾈｼﾞﾌﾗﾝｼﾞ部組立",
"Words": [],
"WorkItems": [
"1. BRACKET にJOINT GREASE-NIPPLE を取付ける(2×6ｶ所)",
"2. 1完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"JOINT GREASE-NIPPLE の取付位置に注意する事",
"スパナは使用不可なので、㉘を使用し取付ける",
"J... | [
{
"WorkName": "ﾎﾞｰﾙﾈｼﾞﾌﾗﾝｼﾞ部組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ：ﾊﾞ-ﾃｨｶﾙﾄﾚｲｽﾄｯｶ-:X20／ﾘﾌﾄ部(001-039)",
"WorkName": "引き出部搭載ﾌﾞﾛｯｸ組立(ﾋﾟﾝ圧入)",
"Words": [],
"WorkItems": [
"1. BLOCK にPIN を圧入する(2ｹ製作)",
"2. BLOCK にPIN を圧入する(4ｶ所)",
"3. PLATE にPIN を圧入する(表面2ｹ､裏面2ｹ)"
],
"WorkPoints": [
"PIN の出代に注意する事",
"･PIN の出代に注意する事･BLOCK の表裏に注意... | [
{
"WorkName": "引き出部搭載ﾌﾞﾛｯｸ組立(ﾋﾟﾝ圧入)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.