input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付①",
"Words": [],
"WorkItems": [
"1. ①のｱﾙﾐﾌﾚｰﾑにNUT SUPPORT を取付",
"2. 1.完成品に⑥をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": ... | [
{
"WorkName": "正流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "528.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付②",
"Words": [],
"WorkItems": [
"1. ①にCABLE を引き回す"
],
"WorkPoints": [
"ｶﾊﾞｰ取付等に干渉しないよう配線を引き回す"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [],
"Jigus... | [
{
"WorkName": "正流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付②",
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "噛み込み無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れ電空ﾚｷﾞｭﾚｰﾀ取付①",
"Words": [
"150㎜",
"150㎜"
],
"WorkItems": [
"1. ①のｱﾙﾐﾌﾚｰﾑにBLOCK を取付",
"2. 1.完成品に⑥をBOLT WASHER で取付"
],
"WorkPoints": [
"前から1列目"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "正流れ電空ﾚｷﾞｭﾚｰﾀ取付①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "150.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れ電空ﾚｷﾞｭﾚｰﾀ取付②",
"Words": [
"1､正面から見て左方向に配線を送る2､ﾌﾚｰﾑ伝いに後方に配線を送る3､ﾌﾚｰﾑ伝いに下へ配線を送る",
"⑪ φ8黒\t3500mm\t2本\u000b\t2500mm\t2本",
"2軸仕様の場合は下記ｷｯﾄより"
],
"WorkItems": [
"2. ①の電空ﾚｷﾞｭﾚｰﾀにCABLE を接続",
"4. 2.完成品の配線､配管をﾌﾚｰﾑに引き回す",
"3. ... | [
{
"WorkName": "正流れ電空ﾚｷﾞｭﾚｰﾀ取付②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れｲｵﾅｲｻﾞｰ取付①",
"Words": [],
"WorkItems": [
"1. ①のｱﾙﾐﾌﾚｰﾑにNUT SUPPORT を取付",
"2. 1.完成品に⑥⑦をBOLT WASHER で取付"
],
"WorkPoints": [
"上からの図",
"正面からの図"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTyp... | [
{
"WorkName": "正流れｲｵﾅｲｻﾞｰ取付①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れｲｵﾅｲｻﾞｰ取付②",
"Words": [
"㉘ φ6 黄\t1500mm\t1本"
],
"WorkItems": [
"2. ①のｲｵﾅｲｻﾞｰ本体とｱﾝﾌﾟを⑥で接続",
"3. 2.完成品のｱﾝﾌﾟに⑦を接続",
"4. 3.完成品のｲｵﾅｲｻﾞｰに1.でカットした配管㉘を接続",
"5. 配線､配管を引き回す",
"1. ㉘を指定の長さにカットする"
],
"WorkPoints": [
"... | [
{
"WorkName": "正流れｲｵﾅｲｻﾞｰ取付②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れHEPAﾕﾆｯﾄ配線引き回し",
"Words": [],
"WorkItems": [
"1. ①にCABLE CABLE CABLE を引き回し、CABLE を㉖で仮固定"
],
"WorkPoints": [
"ｶﾊﾞｰ取付等に干渉しないよう配線を引き回す",
"配線はﾌﾚｰﾑから先端を200mm出す事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],... | [
{
"WorkName": "正流れHEPAﾕﾆｯﾄ配線引き回し",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れ天井ｶﾊﾞｰ取付準備",
"Words": [],
"WorkItems": [
"1. ①のｱﾙﾐﾌﾚｰﾑにSUPPORT ･NUT ･NUT を挿入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工... | [
{
"WorkName": "正流れ天井ｶﾊﾞｰ取付準備",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れHEPAﾌｨﾙﾀｰ取付",
"Words": [],
"WorkItems": [
"1. ①に⑥をBOLT WASHER WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [],
"Jigus": []
} | [
{
"WorkName": "正流れHEPAﾌｨﾙﾀｰ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "正流れ天井ｶﾊﾞｰ取付",
"Words": [],
"WorkItems": [
"1. ①にCOVER ⑦⑧をSCREW WASHER で取付"
],
"WorkPoints": [
"上からの図",
"ﾌﾚｰﾑからのHEPAﾌｨﾙﾀｰ用ｹｰﾌﾞﾙをｸﾞﾛﾒｯﾄからｶﾊﾞｰ上面へ出しておく事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionItems": [],
"Insp... | [
{
"WorkName": "正流れ天井ｶﾊﾞｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "ﾌｪﾗｲﾄｺｱ準備",
"Words": [
"R230\tHEPA(P1)電源/信号線\u000bR231\tHEPA(P1)電源/信号線\u000bR234\tHEPA(P1)電源/信号/ｱｰｽ線\u000bR235\tHEPA(P1)電源/信号/ｱｰｽ線\u000bR236\tHEPA(P1)電源/信号/ｱｰｽ線\u000bR237\tHEPA(P1)電源/信号/ｱｰｽ線",
"R230"
],
"WorkItems": [
"■2. NOISE-FILTE... | [
{
"WorkName": "ﾌｪﾗｲﾄｺｱ準備",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-184",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "HEPAﾌｧﾝ配線接続",
"Words": [
"上から見た図",
"正面側",
"後面側",
"GYG10347",
"上:E1aG10347下:E1bG10347",
"OGG10347",
"RDG10347",
"上:BKG10347下:BKbG10347",
"端子ﾈｼﾞ締めﾄﾙｸ M3-0.6N･m",
"ｱｰｽﾈｼﾞ締めﾄﾙｸ M4-1.4N･m"
],
"WorkItems... | [
{
"WorkName": "HEPAﾌｧﾝ配線接続",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-123",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（正流れP1）(001-034)",
"WorkName": "HEPAﾌｧﾝ配線ﾌｪﾗｲﾄｺｱ取付",
"Words": [
"R230R231",
"R234R235R236R237",
"正面側",
"背面側",
"HEPAﾕﾆｯﾄの電源､信号線に1ﾀｰﾝ(R230~R231)",
"HEPAﾕﾆｯﾄの電源､ｱｰｽ､信号線に1ﾀｰﾝ(R234~R237)"
],
"WorkItems": [
"■1. ①のHEPAﾌｧﾝ配線に②ﾌｪﾗｲﾄｺｱを1ﾀｰﾝで取付"
],
"... | [
{
"WorkName": "HEPAﾌｧﾝ配線ﾌｪﾗｲﾄｺｱ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-184",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾌﾚｰﾑ組立①",
"Words": [],
"WorkItems": [
"1. ①②を③⑯で連結"
],
"WorkPoints": [
"後面",
"上面",
"右面",
"取付は仮固定※4面体にするまで､ﾎﾞﾙﾄの本締めはしない"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"To... | [
{
"WorkName": "逆流れﾌﾚｰﾑ組立①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾌﾚｰﾑ組立②",
"Words": [],
"WorkItems": [
"1. ①②を③⑯で連結"
],
"WorkPoints": [
"取付は仮固定※4面体にするまで､ﾎﾞﾙﾄの本締めはしない",
"後面",
"左面"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsMode... | [
{
"WorkName": "逆流れﾌﾚｰﾑ組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾌﾚｰﾑ組立③",
"Words": [
"585㎜"
],
"WorkItems": [
"1. ①に②③を④⑯で連結"
],
"WorkPoints": [
"上面矢視図",
"取付は仮固定※4面体にするまで､ﾎﾞﾙﾄの本締めはしない"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"Too... | [
{
"WorkName": "逆流れﾌﾚｰﾑ組立③",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:585.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾌﾚｰﾑ組立④",
"Words": [
"765㎜",
"320㎜"
],
"WorkItems": [
"1. ①に②③を④⑯で連結"
],
"WorkPoints": [
"正面",
"取付は仮固定※4面体にするまで､ﾎﾞﾙﾄの本締めはしない"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [... | [
{
"WorkName": "逆流れﾌﾚｰﾑ組立④",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:765.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾌﾚｰﾑ組立⑤",
"Words": [],
"WorkItems": [
"1. 4面体を本締めする",
"2. ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける(8ヶ所)"
],
"WorkPoints": [
"各面の段差が無いように調整し締結する",
"ﾌﾚｰﾑ連結の全てのﾎﾞﾙﾄを本締めする",
"ｾｯﾄｽｸﾘｭｰ締め付け",
"上面",
"後面",
"ｾｯﾄｽｸﾘｭｰ締め付け"
... | [
{
"WorkName": "逆流れﾌﾚｰﾑ組立⑤",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾌﾚｰﾑ組立、ｵﾌﾟｼｮﾝ(HEPAﾌｨﾙﾀｰﾌﾚｰﾑ)",
"Words": [],
"WorkItems": [
"2. 1.完成品に⑥をWASHER BOLT で取付ける",
"1. ①にNUT SUPPORT を取付ける"
],
"WorkPoints": [
"各面の段差が無いように調整し締結する",
"ﾌﾚｰﾑ連結の全てのﾎﾞﾙﾄを本締めする",
"上面",
"この作業は､HEPAﾌｨﾙﾀｰを取付時に実施"
... | [
{
"WorkName": "逆流れﾌﾚｰﾑ組立、ｵﾌﾟｼｮﾝ(HEPAﾌｨﾙﾀｰﾌﾚｰﾑ)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessN... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ扉開閉上部取付①",
"Words": [],
"WorkItems": [
"1. ①に⑥を⑦⑳で取付"
],
"WorkPoints": [
"拡大図",
"正面を内側から見た図"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"Jigu... | [
{
"WorkName": "逆流れ扉開閉上部取付①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ扉開閉上部取付②",
"Words": [
"1.完成品",
"⑪ \t250mm\t1本\t350mm\t1本",
"1.完成品",
"350mm",
"250mm"
],
"WorkItems": [
"2. ①に1.完成品と⑥を接続する",
"1. TUBE を指定の長さでｶｯﾄする"
],
"WorkPoints": [
"内面からの図",
"正面",
"2軸仕様の場合... | [
{
"WorkName": "逆流れ扉開閉上部取付②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ扉開閉上部取付③",
"Words": [
"⑥\t3000mm\t1本"
],
"WorkItems": [
"2. ①に1.完成品を接続する",
"1. TUBE を指定の長さでｶｯﾄする"
],
"WorkPoints": [
"SD-A047677-008のN031 JOINTに接続",
"2軸仕様の場合は下記ｷｯﾄから",
"正面側",
"後面側",
"ｶﾊﾞｰ等に干渉しないよう配線･配... | [
{
"WorkName": "逆流れ扉開閉上部取付③",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ非常停止ｽｲｯﾁ取付①",
"Words": [
"A",
"A矢視図"
],
"WorkItems": [
"1. ①に⑥を⑳㉑で取付"
],
"WorkPoints": [
"端面合わせ",
"正面"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels"... | [
{
"WorkName": "逆流れ非常停止ｽｲｯﾁ取付①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ非常停止ｽｲｯﾁ取付②",
"Words": [
"P1COV5R",
"S204R"
],
"WorkItems": [
"1. ①にCABLE を接続する"
],
"WorkPoints": [
"ｶﾊﾞｰ等に干渉しないよう配線を引き回す"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"T... | [
{
"WorkName": "逆流れ非常停止ｽｲｯﾁ取付②",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ扉開閉下部取付",
"Words": [
"⑪ \t150mm\t1本\t350mm\t1本",
"1.完成品",
"1.完成品",
"350mm",
"150mm"
],
"WorkItems": [
"2. ①に⑥⑦を⑳㉑㉒で取付する",
"3. 2.完成品に1.完成品と⑧を接続する",
"1. TUBE を指定の長さでｶｯﾄする"
],
"WorkPoints": [
"正面",
... | [
{
"WorkName": "逆流れ扉開閉下部取付",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ扉開閉下部取付②",
"Words": [
"⑥\t2000mm\t1本"
],
"WorkItems": [
"1. TUBE を指定の長さでｶｯﾄする",
"2. ①に1.完成品を接続する"
],
"WorkPoints": [
"SD-A047677-012のN031 JOINTに接続",
"2軸仕様の場合は下記ｷｯﾄから",
"正面側",
"後面側",
"ｶﾊﾞｰ等に干渉しないよう配線･配... | [
{
"WorkName": "逆流れ扉開閉下部取付②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾀｰﾐﾅﾙ、D1500取付",
"Words": [],
"WorkItems": [
"1. ①に②を⑯⑰⑱で取付",
"2. 1.完成品にCABLE のD1500を⑲⑳㉑で取付"
],
"WorkPoints": [
"正面"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels"... | [
{
"WorkName": "逆流れﾀｰﾐﾅﾙ、D1500取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾀｰﾐﾅﾙ取付②",
"Words": [],
"WorkItems": [
"1. ①のﾀｰﾐﾅﾙ配線を引き回す"
],
"WorkPoints": [
"ｶﾊﾞｰ等に干渉しないよう配線を引き回す",
"正面側",
"後面側"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsMod... | [
{
"WorkName": "逆流れﾀｰﾐﾅﾙ取付②",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ扉ｽﾄｯﾊﾟｰ取付",
"Words": [],
"WorkItems": [
"1. ①に⑥⑦を⑳で取付"
],
"WorkPoints": [
"正面"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ.26",
... | [
{
"WorkName": "逆流れ扉ｽﾄｯﾊﾟｰ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れｼｰﾙ取付",
"Words": [
"･168㎜･･･1本\u000b･520㎜･･･2本\u000b･605㎜･･･1本"
],
"WorkItems": [
"1. ⑥を指定の長さに切断する",
"2. 1､完成品を①に取付"
],
"WorkPoints": [
"正面",
"内面",
"正面"
],
"Tolks": [],
"InspectionItems": [],
"Inspe... | [
{
"WorkName": "逆流れｼｰﾙ取付",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾋﾝｼﾞ取付",
"Words": [
"50㎜",
"205㎜",
"148㎜",
"35㎜"
],
"WorkItems": [
"1. ①に⑥⑦を⑧で取付"
],
"WorkPoints": [
"ﾋﾝｼﾞのﾋﾟﾝ無しを取付ける"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],... | [
{
"WorkName": "逆流れﾋﾝｼﾞ取付",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ後面ｾﾝｻｰ取付",
"Words": [],
"WorkItems": [
"1. ①に⑥⑦を⑧⑳で取付"
],
"WorkPoints": [
"後面",
"矢視図"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使... | [
{
"WorkName": "逆流れ後面ｾﾝｻｰ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付①",
"Words": [
"A"
],
"WorkItems": [
"1. ①のｱﾙﾐﾌﾚｰﾑの指定の位置に⑦⑧を取付",
"2. 1.完成品に⑥を⑳㉑で取付"
],
"WorkPoints": [
"⑦⑧はﾌﾚｰﾑの内面に取付の事\u000b距離はﾈｼﾞ穴ｾﾝﾀｰの寸法",
"正面",
"A矢視図",
"正面"
],
"Tolks": [],
"Inspect... | [
{
"WorkName": "逆流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付②",
"Words": [
"E0131P",
"P1TB7R"
],
"WorkItems": [
"1. ①に⑥を引き回す"
],
"WorkPoints": [
"ｶﾊﾞｰ取付等に干渉しないよう配線を引き回す"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"Too... | [
{
"WorkName": "逆流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付②",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ電空ﾚｷﾞｭﾚｰﾀ取付①",
"Words": [
"A"
],
"WorkItems": [
"1. ①に⑥を⑳㉑で取付"
],
"WorkPoints": [
"A矢視図"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguN... | [
{
"WorkName": "逆流れ電空ﾚｷﾞｭﾚｰﾀ取付①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ電空ﾚｷﾞｭﾚｰﾀ取付②",
"Words": [
"1､正面から見て左方向に配線･配管を送る2､ﾌﾚｰﾑ伝いに後方に配線･配管を送る3､ﾌﾚｰﾑ伝いに下へ配線･配管を送る",
"B4104R",
"P1REG1R",
"B4105R",
"⑪ \t4000mm\t2本\t5000mm\t2本",
"1.完成品",
"5000mm",
"1.完成品",
"4000mm",
"L側\u000bIN:P0... | [
{
"WorkName": "逆流れ電空ﾚｷﾞｭﾚｰﾀ取付②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ上下流仮置ｲｵﾅｲｻﾞｰ取付(ｵﾌﾟｼｮﾝ)①",
"Words": [
"9-1",
"9-2",
"9-3",
"8-1",
"8-2",
"8-3",
"8-4"
],
"WorkItems": [
"1. ①に⑦を⑨で指定の位置に取付",
"2. 1.完成品に⑥を⑧で指定の位置に取付"
],
"WorkPoints": [
"上からの図",
"左側内面",
... | [
{
"WorkName": "逆流れ上下流仮置ｲｵﾅｲｻﾞｰ取付(ｵﾌﾟｼｮﾝ)①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ上下流仮置ｲｵﾅｲｻﾞｰ取付(ｵﾌﾟｼｮﾝ)②",
"Words": [
"⑪ \t2000mm\t1本",
"ｱﾝﾌﾟ側:BLACKE2006P\u000bﾊﾞｰ側:E2006P",
"ｱﾝﾌﾟ側:GLAYE2006P",
"1E2006R"
],
"WorkItems": [
"2. ①のｲｵﾅｲｻﾞｰ本体とｱﾝﾌﾟを⑥で接続",
"3. 2.完成品のｱﾝﾌﾟに⑦を接続",
"4. 3.完成品のｲｵﾅｲｻﾞｰに1.... | [
{
"WorkName": "逆流れ上下流仮置ｲｵﾅｲｻﾞｰ取付(ｵﾌﾟｼｮﾝ)②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れHEPAﾕﾆｯﾄ配線引き回し",
"Words": [
"BKbG10347-E1aG10347",
"ADPW-01/ADPW-12",
"1G10340-8R",
"5X012",
"BKG10347/RDG10347",
"OGG10347/GYG10347",
"E1bG10347"
],
"WorkItems": [
"1. ①に⑥・⑦・⑨を引き回し、⑧を㉖で仮固定"
],
"WorkP... | [
{
"WorkName": "逆流れHEPAﾕﾆｯﾄ配線引き回し",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ天井ｶﾊﾞｰ取付準備",
"Words": [],
"WorkItems": [
"1. ①のｱﾙﾐﾌﾚｰﾑに⑥⑦⑧を挿入"
],
"WorkPoints": [
"HEPAﾌｨﾙﾀｰ取付仕様時"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"Jig... | [
{
"WorkName": "逆流れ天井ｶﾊﾞｰ取付準備",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れHEPAﾌｨﾙﾀｰ取付",
"Words": [],
"WorkItems": [
"1. ①に⑥をBOLT WASHER WASHER で組付け"
],
"WorkPoints": [
"この作業は､HEPAﾌｨﾙﾀｰを取付時に実施"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": ... | [
{
"WorkName": "逆流れHEPAﾌｨﾙﾀｰ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "逆流れ天井ｶﾊﾞｰ取付",
"Words": [],
"WorkItems": [
"1. ①にCOVER ⑦⑧をSCREW WASHER で取付"
],
"WorkPoints": [
"上からの図",
"ﾌﾚｰﾑからのHEPAﾌｨﾙﾀｰ用ｹｰﾌﾞﾙをｸﾞﾛﾒｯﾄからｶﾊﾞｰ上面へ出しておく事",
"HEPAﾌｨﾙﾀｰ取付仕様時"
],
"Tolks": [],
"InspectionItems": [],
"Inspec... | [
{
"WorkName": "逆流れ天井ｶﾊﾞｰ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "ﾌｪﾗｲﾄｺｱ準備",
"Words": [
"R230\tHEPA(P1)電源/信号線\u000bR231\tHEPA(P1)電源/信号線\u000bR234\tHEPA(P1)電源/信号/ｱｰｽ線\u000bR235\tHEPA(P1)電源/信号/ｱｰｽ線\u000bR236\tHEPA(P1)電源/信号/ｱｰｽ線\u000bR237\tHEPA(P1)電源/信号/ｱｰｽ線",
"R230"
],
"WorkItems": [
"■2. ⑥に⑪を貼付けする",... | [
{
"WorkName": "ﾌｪﾗｲﾄｺｱ準備",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-184",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "HEPAﾌｧﾝ配線接続",
"Words": [
"上から見た図",
"正面側",
"後面側",
"GYG10347",
"上:E1aG10347下:E1bG10347",
"OGG10347",
"RDG10347",
"上:BKG10347下:BKbG10347",
"端子ﾈｼﾞ締めﾄﾙｸ M3-0.6N･m",
"ｱｰｽﾈｼﾞ締めﾄﾙｸ M4-1.4N･m"
],
"WorkItems... | [
{
"WorkName": "HEPAﾌｧﾝ配線接続",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-123",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "本体部_FRAME（逆流れP1）(001-033)",
"WorkName": "HEPAﾌｧﾝ配線ﾌｪﾗｲﾄｺｱ取付",
"Words": [
"R230R231",
"R234R235R236R237",
"正面側",
"背面側",
"HEPAﾕﾆｯﾄの電源､信号線に1ﾀｰﾝ(R230~R231)",
"HEPAﾕﾆｯﾄの電源､ｱｰｽ､信号線に1ﾀｰﾝ(R234~R237)"
],
"WorkItems": [
"■1. ①のHEPAﾌｧﾝ配線に②ﾌｪﾗｲﾄｺｱを1ﾀｰﾝで取付"
],
"... | [
{
"WorkName": "HEPAﾌｧﾝ配線ﾌｪﾗｲﾄｺｱ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-184",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "非常停止SW組立",
"Words": [],
"WorkItems": [
"1. BRACKET にLABEL を貼付",
"■2. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付"
],
"WorkPoints": [
"LABEL をBRACKET の中心穴に均等貼付",
"ﾎﾞﾀﾝ側を1.完成品に挿入し､付属のﾅｯﾄで締結",
"型式確認･ｼﾘｱﾙNo記録"
... | [
{
"WorkName": "非常停止SW組立",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立①",
"Words": [
"3mm",
"1B10110-5R"
],
"WorkItems": [
"1. CYLINDER にSWITCH を取付",
"2. 1完成品にLABEL TERMINAL PROCESS を取付"
],
"WorkPoints": [
"ｾﾝｻｰの角をｼﾘﾝﾀﾞｰ側面から3mmに合わせて取付",
"被覆端面とLABEL TERMINAL PROCESS の端面... | [
{
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立②",
"Words": [
"1.完成品",
"×2",
"×2",
"2.完成品",
"2.完成品"
],
"WorkItems": [
"1. ①にJOINT を取付",
"2. 1完成品にJOINT を取付",
"4. 3.完成品にSUPPORT NUT BOLT WASHER を㉘に入れマスキングテープで止め同梱",
"3. BRACKET に2.完成品をBOLT W... | [
{
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "扉ｷｬｯﾁ部組立",
"Words": [
"×2",
"×2"
],
"WorkItems": [
"1. BRACKET にCATCH をBOLT WASHER で取付",
"2. 1.完成品にSUPPORT NUT BOLT WASHER を㉗に入れマスキングテープで止め同梱"
],
"WorkPoints": [
"本体ｶﾊﾞｰﾌﾚｰﾑに固定の為"
],
"Tolks": [],
"InspectionI... | [
{
"WorkName": "扉ｷｬｯﾁ部組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "扉ｽﾄｯﾊﾟｰ部組立",
"Words": [
"この作業では勝手違いを各1個製作"
],
"WorkItems": [
"1. PLATE にRUBBER-LEG をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsM... | [
{
"WorkName": "扉ｽﾄｯﾊﾟｰ部組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "扉ﾏｸﾞﾈｯﾄSW部組立",
"Words": [
"S308",
"2.完成品",
"PCOVUSA001"
],
"WorkItems": [
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 2.完成品にLABEL TERMINAL PROCESS LABEL TERMINAL PROCESS を取付",
"2. BRACKET にSWITCH をBOLT WASHER WASHER NUT-PL... | [
{
"WorkName": "扉ﾏｸﾞﾈｯﾄSW部組立",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "扉ｽﾄｯﾊﾟｰ取付①",
"Words": [
"正面側",
"後面側",
"底面側",
"左面側",
"A",
"B",
"A矢視図",
"B矢視図"
],
"WorkItems": [
"1. ⑥に①②をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑと平行",
"端面合わせ",
"端面合わせ"
],
"Tolk... | [
{
"WorkName": "扉ｽﾄｯﾊﾟｰ取付①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "ｾｰﾌﾃｨｰｶﾊﾞｰｽｲｯﾁ取付",
"Words": [
"正面側",
"後面側",
"底面側",
"左面側",
"締付ﾄﾙｸ 1.0N･m"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑと平行",
"端面合わせ"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "ｾｰﾌﾃｨｰｶﾊﾞｰｽｲｯﾁ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "非常停止ｽｲｯﾁ取付",
"Words": [
"正面側",
"後面側",
"底面側",
"左面側",
"A",
"A矢視図"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"端面合わせ"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": ... | [
{
"WorkName": "非常停止ｽｲｯﾁ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "ﾋﾝｼﾞ取付",
"Words": [
"正面側",
"後面側",
"底面側",
"左面側",
"A",
"A矢視図",
"B",
"B矢視図"
],
"WorkItems": [
"1. ①にHINGE をSCREW で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑに対して平行"
],
"Tolks": [],
"InspectionItems": [... | [
{
"WorkName": "ﾋﾝｼﾞ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "扉ｽﾄｯﾊﾟｰ取付②",
"Words": [
"正面側",
"後面側",
"底面側",
"左面側",
"A",
"A矢視図",
"B",
"B矢視図"
],
"WorkItems": [
"1. ①にSPACER RUBBER-LEG をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"... | [
{
"WorkName": "扉ｽﾄｯﾊﾟｰ取付②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "ｷｬｯﾌﾟ取付",
"Words": [
"正面側",
"後面側",
"底面側",
"左面側"
],
"WorkItems": [
"1. ①にCAP を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPart... | [
{
"WorkName": "ｷｬｯﾌﾟ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "底板取付",
"Words": [
"底面側",
"左面側",
"正面側",
"後面側"
],
"WorkItems": [
"1. ①にCOVER COVER COVER をWASHER SCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionItems": [],
"InspectionNos": [],... | [
{
"WorkName": "底板取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全... | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "ｽﾀﾝﾄﾞ取付①",
"Words": [
"底面側",
"左面側",
"正面側",
"後面側",
"×3",
"×3",
"101㎜",
"101㎜",
"101㎜",
"101㎜"
],
"WorkItems": [
"1. ①にSUPPORT NUT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionIt... | [
{
"WorkName": "ｽﾀﾝﾄﾞ取付①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "ｽﾀﾝﾄﾞ取付②",
"Words": [
"底面側",
"左面側",
"正面側",
"後面側",
"×3",
"×3"
],
"WorkItems": [
"1. ①に⑥⑦をWASHER BOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 11.5N･m"
],
"InspectionItems": [],
"Inspection... | [
{
"WorkName": "ｽﾀﾝﾄﾞ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:中間カバー(W-13)(001-016)",
"WorkName": "払出",
"Words": [
"1. ①~⑨⑯⑰をﾄﾞｯｷﾝｸﾞ工程へ払い出し"
],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsModels": [],
"Jigus": []
} | [
{
"WorkName": "払出",
"QualityItem": "払出確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "非常停止SW組立",
"Words": [],
"WorkItems": [
"1. BRACKET にLABEL を貼付",
"■2. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付"
],
"WorkPoints": [
"LABEL をBRACKET の中心穴に均等貼付",
"ﾎﾞﾀﾝ側を1.完成品に挿入し､付属のﾅｯﾄで締結",
"型式確認･ｼﾘｱﾙNo記録... | [
{
"WorkName": "非常停止SW組立",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立①",
"Words": [
"3mm",
"1B10110-5R"
],
"WorkItems": [
"1. CYLINDER にSWITCH を取付",
"2. 1完成品にLABEL TERMINAL PROCESS を取付"
],
"WorkPoints": [
"ｾﾝｻｰの角をｼﾘﾝﾀﾞｰ側面から3mmに合わせて取付",
"被覆端面とLABEL TERMINAL PROCESS ... | [
{
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立②",
"Words": [
"×2",
"×2",
"2.完成品",
"2.完成品",
"1.完成品"
],
"WorkItems": [
"1. ①にJOINT を取付",
"2. 1完成品にJOINT を取付",
"4. 3.完成品にSUPPORT NUT BOLT WASHER を㉘に入れマスキングテープで止め同梱",
"3. BRACKET に2.完成品をBOL... | [
{
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "扉ｷｬｯﾁ部組立",
"Words": [
"×2",
"×2"
],
"WorkItems": [
"1. BRACKET にCATCH をBOLT WASHER で取付",
"2. 1.完成品にSUPPORT NUT BOLT WASHER を㉗に入れマスキングテープで止め同梱"
],
"WorkPoints": [
"本体ｶﾊﾞｰﾌﾚｰﾑに固定の為"
],
"Tolks": [],
"Inspecti... | [
{
"WorkName": "扉ｷｬｯﾁ部組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "扉ｽﾄｯﾊﾟｰ部組立",
"Words": [
"この作業では勝手違いを各1個製作"
],
"WorkItems": [
"1. PLATE にRUBBER-LEG をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPar... | [
{
"WorkName": "扉ｽﾄｯﾊﾟｰ部組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "扉ﾏｸﾞﾈｯﾄSW部組立",
"Words": [
"S308",
"2.完成品",
"PCOVUSA001"
],
"WorkItems": [
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 2.完成品にLABEL TERMINAL PROCESS LABEL TERMINAL PROCESS を取付",
"2. BRACKET にSWITCH をBOLT WASHER WASHER NUT... | [
{
"WorkName": "扉ﾏｸﾞﾈｯﾄSW部組立",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "扉ｽﾄｯﾊﾟｰ取付①",
"Words": [
"正面側",
"後面側",
"底面側",
"右面側",
"A",
"B",
"A矢視図",
"B矢視図"
],
"WorkItems": [
"1. ⑥に①②をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑと平行",
"端面合わせ",
"端面合わせ"
],
"T... | [
{
"WorkName": "扉ｽﾄｯﾊﾟｰ取付①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "ｾｰﾌﾃｨｰｶﾊﾞｰｽｲｯﾁ取付",
"Words": [
"正面側",
"後面側",
"底面側",
"右面側",
"締付ﾄﾙｸ 1.0N･m"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑと平行",
"端面合わせ"
],
"Tolks": [],
"InspectionItems": [... | [
{
"WorkName": "ｾｰﾌﾃｨｰｶﾊﾞｰｽｲｯﾁ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "非常停止ｽｲｯﾁ取付",
"Words": [
"正面側",
"後面側",
"底面側",
"右面側",
"A",
"A矢視図"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"端面合わせ"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos... | [
{
"WorkName": "非常停止ｽｲｯﾁ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "ﾋﾝｼﾞ取付",
"Words": [
"正面側",
"後面側",
"底面側",
"右面側",
"A",
"A矢視図",
"B",
"B矢視図"
],
"WorkItems": [
"1. ①にHINGE をSCREW で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑに対して平行"
],
"Tolks": [],
"InspectionItems"... | [
{
"WorkName": "ﾋﾝｼﾞ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "扉ｽﾄｯﾊﾟｰ取付②",
"Words": [
"正面側",
"後面側",
"底面側",
"右面側",
"A",
"A矢視図",
"B",
"B矢視図"
],
"WorkItems": [
"1. ①にSPACER RUBBER-LEG をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "扉ｽﾄｯﾊﾟｰ取付②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "ｷｬｯﾌﾟ取付",
"Words": [
"正面側",
"後面側",
"底面側",
"右面側"
],
"WorkItems": [
"1. ①にCAP を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolP... | [
{
"WorkName": "ｷｬｯﾌﾟ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "底板取付",
"Words": [
"底面側",
"右面側",
"正面側",
"後面側"
],
"WorkItems": [
"1. ①にCOVER COVER COVER をWASHER SCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionItems": [],
"InspectionNos": ... | [
{
"WorkName": "底板取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全... | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "ｽﾀﾝﾄﾞ取付①",
"Words": [
"底面側",
"右面側",
"正面側",
"後面側",
"×3",
"×3",
"101㎜",
"101㎜",
"101㎜",
"101㎜"
],
"WorkItems": [
"1. ①にSUPPORT NUT を取付"
],
"WorkPoints": [],
"Tolks": [],
"Inspectio... | [
{
"WorkName": "ｽﾀﾝﾄﾞ取付①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "ｽﾀﾝﾄﾞ取付②",
"Words": [
"底面側",
"右面側",
"正面側",
"後面側",
"×3",
"×3"
],
"WorkItems": [
"1. ①に⑥⑦をWASHER BOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 11.5N･m"
],
"InspectionItems": [],
"Inspect... | [
{
"WorkName": "ｽﾀﾝﾄﾞ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:中間カバー(W-13)(001-016)",
"WorkName": "払出",
"Words": [
"1. ①~⑨⑯⑰をﾄﾞｯｷﾝｸﾞ工程へ払い出し"
],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
],
"ToolPartsModels": [],
"Jigus": []
} | [
{
"WorkName": "払出",
"QualityItem": "払出確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "CPU_BOX組立",
"Words": [],
"WorkItems": [
"■1. BOX の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. BOX にLABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"筐体上面にﾗﾍﾞﾙを貼付 (貼付方向に注意)",
"EXTENDED UNITがある場合のみLABEL を貼付ける"
],
"Tolks": [],
... | [
{
"WorkName": "CPU_BOX組立",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "CPUﾎﾞｰﾄﾞ確認(K306)",
"Words": [
"ｼﾘｱﾙNo"
],
"WorkItems": [
"2. 付属のWindowsﾗｲｾﾝｽｼｰﾙのﾗｲｾﾝｽ番号を検査表に記入する",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [
"検査表①:型式･検査... | [
{
"WorkName": "CPUﾎﾞｰﾄﾞ確認(K306)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "CPUﾎﾞｰﾄﾞ設定、取付(K306)",
"Words": [
"ｶﾊﾞｰ",
"ﾈｼﾞ"
],
"WorkItems": [
"★1. ①に②を取付ける",
"★2. ②CPUﾎﾞｰﾄﾞのｶｰﾄﾞｽﾛｯﾄにREMOVABLE-MEMORY を挿入する",
"3. 2完成品にCONNECTOR-COVER を取付ける"
],
"WorkPoints": [
"K306",
"挿入方向に... | [
{
"WorkName": "CPUﾎﾞｰﾄﾞ設定、取付(K306)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K303、K305)",
"Words": [],
"WorkItems": [
"★2. ⑤にPOWER-SUPPLY を取付ける",
"■★1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNoを検査表に記入する"
],
"WorkPoints": [
"K303",
"K305",
"型式",
"ｼﾘｱﾙNo.",
"取付け時CPUﾎﾞｰﾄﾞに擦らないよう注意... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K303、K305)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K302、K304)",
"Words": [],
"WorkItems": [
"■★1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. ⑤にPOWER-SUPPLY を取付ける"
],
"WorkPoints": [
"K302",
"K304",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄ... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K302、K304)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K307)",
"Words": [
"①付属品",
"分岐ｹｰﾌﾞﾙ",
"設定:0"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"5. 4完成品にCONNECTOR-COVER を取付ける",
"★4. ⑤に3.完成品を取付ける",
"★3.... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K307)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K308)",
"Words": [
"設定:0"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける",
"★2. PCB-COM のｽｲｯﾁ設定確認"
],
"WorkPoints": [
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"K308"
],
"T... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K308)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K309)",
"Words": [
"設定:0"
],
"WorkItems": [
"★2. PCB-COM のｽｲｯﾁ設定確認",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K309",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"T... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K309)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K310-K314)",
"Words": [
"-K310用",
"-K311用",
"-K312用",
"-K313用",
"-K314用"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する(K310-K314)",
"★2. PCB-COM のｽｲｯﾁ､ｼﾞｬﾝﾊﾟｰ設定確認(K310-K314)",
... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K310-K314)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K315)",
"Words": [
"設定:0"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K315",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"T... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K315)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K316)",
"Words": [
"設定:0"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K316",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"T... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K316)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K317)",
"Words": [
"設定:0"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K317",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"T... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K317)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "固定用ﾌﾞﾗｹｯﾄ取付(CPUUNIT)",
"Words": [],
"WorkItems": [
"1. ⑤にBRACKET BRACKET を取付ける"
],
"WorkPoints": [
"面合わせ",
"BOX組付けﾈｼﾞ",
"⑤BOX組付けﾈｼﾞを緩めて､BRACKET BRACKET を挟み込み再度ﾈｼﾞで締付ける"
],
"Tolks": [],
"InspectionItems": ... | [
{
"WorkName": "固定用ﾌﾞﾗｹｯﾄ取付(CPUUNIT)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "EXTENDEDUNIT設定、ﾎﾞｰﾄﾞ取付",
"Words": [
"CPZ-CPZ13D(OP)A01",
"-K335",
"-K334",
"-K340",
"-K341",
"-K342"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. PCB-COM にLABEL を貼付ける",
"★3. ... | [
{
"WorkName": "EXTENDEDUNIT設定、ﾎﾞｰﾄﾞ取付",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-302",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K340)",
"Words": [
"設定:7"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ､ｼﾞｬﾝﾊﾟｰ設定確認",
"★3. ⑤にPCB-COM PANEL ､⑤付属品を取付ける"
],
"WorkPoints": [
"K340",
"ｼﾞｬﾝﾊﾟｰが無いこ... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K340)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-302",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K341)",
"Words": [
"設定:1"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K341",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"T... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K341)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-302",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K342)",
"Words": [
"設定:1"
],
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K342",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"T... | [
{
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K342)",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-302",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "固定用ﾌﾞﾗｹｯﾄ取付(EXTENDEDUNIT)",
"Words": [],
"WorkItems": [
"1. ⑤にBRACKET BRACKET を取付ける"
],
"WorkPoints": [
"面合わせ",
"BOX組付けﾈｼﾞ",
"⑤BOX組付けﾈｼﾞを緩めて､BRACKET BRACKET を挟み込み再度ﾈｼﾞで締付ける"
],
"Tolks": [],
"InspectionIte... | [
{
"WorkName": "固定用ﾌﾞﾗｹｯﾄ取付(EXTENDEDUNIT)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "APX300-DM ： <a02-03> CPU UNIT（001-019）",
"WorkName": "増設ｹｰﾌﾞﾙﾗﾍﾞﾙ結束",
"Words": [
"CN1K333",
"CN1K334",
"CN1K334",
"CN1K333"
],
"WorkItems": [
"1. ①にLABEL を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [
"検査表①:ﾏｰｷﾝｸﾞﾀｲ取付確認"
],
"In... | [
{
"WorkName": "増設ｹｰﾌﾞﾙﾗﾍﾞﾙ結束",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-296",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:銘板:中間カバー(001-007)",
"WorkName": "中間ｶﾊﾞｰ銘板貼付1",
"Words": [
">PC<",
">PC<"
],
"WorkItems": [
"2. COVER にLABEL LABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"正流れ時",
"逆流れ時",
"逆流れ時は下記ｷｯﾄより"
],
"Tolks":... | [
{
"WorkName": "中間ｶﾊﾞｰ銘板貼付1",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:銘板:中間カバー(001-007)",
"WorkName": "中間ｶﾊﾞｰ銘板貼付2",
"Words": [],
"WorkItems": [
"1. COVER にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"正流れ時",
"逆流れ時",
"逆流れ時は下記ｷｯﾄより"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
... | [
{
"WorkName": "中間ｶﾊﾞｰ銘板貼付2",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:銘板:中間カバー(001-007)",
"WorkName": "中間ｶﾊﾞｰ銘板貼付3",
"Words": [
">PC<",
">PC<",
">PC<",
">PC<"
],
"WorkItems": [
"■3. FRAME-KIT にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPo... | [
{
"WorkName": "中間ｶﾊﾞｰ銘板貼付3",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:銘板:中間カバー(001-007)",
"WorkName": "中間ｶﾊﾞｰ銘板貼付4",
"Words": [
">PC<",
">PC<"
],
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"正流れ時",
"逆流れ時",
"逆流れ時は下記ｷｯﾄより"
],
"Tolks": [],
... | [
{
"WorkName": "中間ｶﾊﾞｰ銘板貼付4",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.