data stringlengths 14 24.3k |
|---|
Rave#7710: uh I'll check when this run is finished
Rave#7710: probably about 10 mins to go
whiteshark#1560: wait 1.4 is 1.35 measured, i bet thats the same as me and you cant get over 1.35 no matter what you set
Rave#7710: As I say I couldn't figure out how to set more than 1.4v, which is why I'll see if I can kill LL... |
whiteshark#1560: meh
Rave#7710: Hmm, just had a look again, either CHL8225G or CHL82256
Rave#7710: can't tell if it's a 6 or G
whiteshark#1560: mine says G
Rave#7710: ah it's G
Rave#7710: Ah I get it, 5225 is 5 phase
Rave#7710: 5228 is 8 phase
whiteshark#1560: "Dynamic voltage control by 2-bit parallel interface with ... |
whiteshark#1560: the vidsel is for registers you have to set with i2c
Rave#7710: yeah idk how to i2c at all
Rave#7710: Was doing i2c dumps of the card but some of the values were changing literally beteen each dump, without changing anything
whiteshark#1560: i know even less since i dont know how to do i2c dumps
yosari... |
Rave#7710: CHiL is owned by infineon I believe
yosarianilives#1841: And my vrm is only a 4+1(2?)
Rave#7710: atleast they are now, not sure at the time
whiteshark#1560: well the specsheet is hosted on their site
Rave#7710: yeah, IR and CHiL controller are pretty similar, I believe
yosarianilives#1841: Yeah, mine was a c... |
yosarianilives#1841: No idea what I'm actually getting
yosarianilives#1841: But when I hex edited trixx to 1.5v
yosarianilives#1841: It still seemed limited by the card
yosarianilives#1841: And iirc voltage limits on Tahiti are at the hw level or something
yosarianilives#1841: Although I guess I got good enough results... |
Rave#7710: but worth a try
Rave#7710: alright, I think I should have 1450mv set now, time to flash it
Rave#7710: well, the card boots, that's a good sign
pkkshadow#5844: no magic smoke?
Rave#7710: 1.35v
whiteshark#1560: does it clock up?
Rave#7710: Yeah was using gpu-z render test so it's at max p-state
whiteshark#1560... |
Frito#0907: stop mining and start overclocking? 😉
hvilepute#5539: xD
Frito#0907: sorry all i got
Frito#0907: i dont multi gpu
Frito#0907: but i imagine you need to use a program that can select each one
Frito#0907: and set individually
twitchytoes#6978: Each gpu has to be selected separately and tuned separately afaik... |
hvilepute#5539: I did find a solution, but I'd like to know if it is safe. I adjusted the voltage curve and all the settings I want on one card, apply it and make sure it sticks. Then changing that cfg file to read only and replace that cfg with all the others and rename. All cards are now running at same freq/voltage,... |
pkkshadow#5844: on my amd card, i set a clock on trixx, but it doesn't show til the card has load on it
pkkshadow#5844: 300mhz is the idle clock
pkkshadow#5844: 1250 is the full load clock
hvilepute#5539: https://cdn.discordapp.com/attachments/305981966292090881/391578684445818880/curve.png
hvilepute#5539: guess it ca... |
Rave#7710: @buildzoid did you ever test hardmodded vhbm after the SoC clocks limitations got lifted?
Deleted User#0000: Just allow you to push hbm clocks higher?
buildzoid#6254: it doesn't do anything
buildzoid#6254: need to do more testing when I get back
buildzoid#6254: my last test with lifted SOC clocks showed a wa... |
buildzoid#6254: on the 7970
buildzoid#6254: and I think the card might have had i2c writes just disabled out right
buildzoid#6254: because I never did manage to change the Vcore
buildzoid#6254: or really do anything
Deleted User#0000: How’d you raise SOC? Power play tables?
Rave#7710: It used to be capped at 1100
Rave#... |
buildzoid#6254: when a lot of them change
twitchytoes#6978: Yeah
buildzoid#6254: is really hard
twitchytoes#6978: I get it
buildzoid#6254: when you also don't have an encoding table
buildzoid#6254: cuz at idle you get a whole bunch of values
buildzoid#6254: one of which probably means 0.875V
buildzoid#6254: and at load... |
buildzoid#6254: also the voltage controller has offset registers
buildzoid#6254: so if the GPU maker feels like it they set +100mv offset
buildzoid#6254: and run 1.1V VID
twitchytoes#6978: Yeah
twitchytoes#6978: My thought was having an odd voltage, as in one that isn't similar to any other to set it apart and try to s... |
buildzoid#6254: and the voltage controllers also emply various extensions
buildzoid#6254: so the CHL8228G has a gamer mode to go past the usual end of the VID table which is either 1.55 or 1.625V depending on what standard the table is in
twitchytoes#6978: Way over my head anyway
whiteshark#1560: people with vega on th... |
Keithxm#6077: Yea, just wondering if my settings were wrong
Rave#7710: with temps also being a factor too
Keithxm#6077: It was set to max 92C
Keithxm#6077: but doubt it went higher than 73C
Rave#7710: your settings look find to me, if you go higher on the core clock offset, does it crash and/or artifact?
Keithxm#6077: ... |
Keithxm#6077: both are stable
Keithxm#6077: Oh. fan Speed i using default
Keithxm#6077: at which temp should it go 100%?
Keithxm#6077: 60C?
Rave#7710: Test it out
Keithxm#6077: any recommended settings for a start?
Rave#7710: Tbh if you can beare the fans being at 100% then by all means go for it, otherwise set a more ... |
Rave#7710: oh that's nvidia being nvidia
Armin#3486: No, Pascal is rarely voltage limited with ambient cooling
Keithxm#6077: Ok.. I guess to be safe.. I set to 100% first to get a stable OC.. then slowly bring Voltage down.. to see where it turns unstable.. hopefully it won't go 0% again.
Rave#7710: iirc, the maxing ou... |
Keithxm#6077: And here I am.. hoping it will not go over 60C at 100%.. lol
Armin#3486: Well air cooling can't compete with water on a GPU
Timo#2874: my 1080 is around 55C at max load
Timo#2874: thats just with MX4 and an 120mm AiO
Timo#2874: my 1080 still clocks like shit but not *as* shit as before
Timo#2874: temp mat... |
hvilepute#5539: if my 1070 is hardlocked, then undervolting doesnt actually work?
hvilepute#5539: temps definitely went down tho
hvilepute#5539: nvm, theese are maxwell
hvilepute#5539: hm, no im not sure actually 😛
hvilepute#5539: damn
Armin#3486: I meant that they are capped at 1.093V
Armin#3486: You can get lower
hv... |
Armin#3486: Yeah but I'm pretty sure you can clock higher
hvilepute#5539: it will reduce the lifetime tho? Its for miing so they are running 24/7
hvilepute#5539: mining*
hvilepute#5539: obviously the temps will affect the lifetime more, but I thought oc could do it too?
Armin#3486: If anything it will increase the life... |
hvilepute#5539: I started roughly a month ago myself, and I built a small rig 3 days ago
hvilepute#5539: paying quite well actually
hvilepute#5539: @Armin thank you for your time! 😃
Armin#3486: No problem man. Unfortunately electricity is too expensive here to really be worth it
hvilepute#5539: https://linustechtips.c... |
Armin#3486: Pascal loves low temperatures
Armin#3486: Roughly every 10 degrees more I require an additional voltage step to get it stable
Armin#3486: Up to a certain point where it's just unstable and GPUBoost clocks down
Drew[bedsidegamma]#9440: Okay I thought 130 was stable just crashed after about a hour of gaming
D... |
Drew[bedsidegamma]#9440: I pushed it 500 +
Drew[bedsidegamma]#9440: Right now 1314
Drew[bedsidegamma]#9440: But it's only a 250 boost rn
Just another courier#6988: would you say it's worth it to go from a gtx 1060 6gb to a rx 580 8gb for the freesync?
Just another courier#6988: and possibily better overclocker
Rave#771... |
Marcus Antonius#1439: No, you won't be near your temp limit but you're probably power limited but 65°C is very hot for maxwell on liquid
Marcus Antonius#1439: My GTX 980 picked up almost 100MHz (around 150MHz iirc) from a 30°C drop,
HabibiFresh#8465: ya I idle 35
HabibiFresh#8465: thing is the raditor that comes with t... |
Justifiedparanoia#4764: couldnt remember if sub zero got pinged with experienced
Justifiedparanoia#4764: heres the limit tables as well
Justifiedparanoia#4764: https://cdn.discordapp.com/attachments/305981966292090881/393593003023007744/unknown.png
Justifiedparanoia#4764: should i just try and copy all the settings ac... |
yosarianilives#1841: wait
yosarianilives#1841: just the flashing?
Justifiedparanoia#4764: having issues with the flashing, so wante dto check my settings
yosarianilives#1841: If you're sure you've got a working bios use atiwinflash through cmd so you can force install the bios
yosarianilives#1841: Cause otherwise it wo... |
Justifiedparanoia#4764: will do
Justifiedparanoia#4764: or might just try and move all settings over to a known working bios
Rave#7710: you have to force flash it
Rave#7710: if your card isn't an asus card
unused#4429: I eventually got the bios to extract and threw the new one on
unused#4429: All seems good so far
unus... |
hvilepute#5539: So basically just hang it from there
hvilepute#5539: guess I could place it flat as well, would be easier if I have the space
Mickulty#1560: oh, yeah straight down hanging from it should be a-ok
hvilepute#5539: thank you 😃
the b#4909: I wonder if it would be ok with that new sapphire vega
the b#4909: t... |
Mickulty#1560: off the top of my head
Mickulty#1560: x265 should tell you fwiw
lardy#1580: yeah I got it
Frito#0907: new version of gpupi doesn't need it
Frito#0907: 3.0
Frito#0907: Timer: Invariant TSC (4.20 MHz) is what it reports for me
Frito#0907: he's made some nice changes to it hardware reporting is much improv... |
Niobium#6334: 1030 pretesting on air https://cdn.discordapp.com/attachments/305981966292090881/394706909547986945/20171224_232317.jpg
yosarianilives#1841: How dem sliders looking?
Niobium#6334: Not using sliders 😉
Niobium#6334: I'm going to be fucked as soon as the card is on LN2 though
yosarianilives#1841: Bios mod w... |
Niobium#6334: Unless I ask MSI nicely 🤔
Niobium#6334: I honestly think that getting high clocks working is going to be the hardest part of the comp.
Niobium#6334: No issues on air though : http://hwbot.org/submission/3743589
Drew[bedsidegamma]#9440: What is safe temp for 1080 FE edition?
Drew[bedsidegamma]#9440: I hat... |
Chloe von Einzbern#0001: i have a problem
Chloe von Einzbern#0001: i wanted to get this damn gpu stable
Chloe von Einzbern#0001: but i try ocing but i get laggings, and crashing in heaven
Chloe von Einzbern#0001: and i only raised power limit to 150% and core clock to 90mhz
Chloe von Einzbern#0001: i was hoping i find... |
Chloe von Einzbern#0001: https://pcpartpicker.com/list/4cJCsJ
Chloe von Einzbern#0001: well this is my pc
Chloe von Einzbern#0001: so i hope that is enough info
Chloe von Einzbern#0001: and uhm this is what it do with gigabyte oc tool , https://www.amazon.de/clouddrive/share/UmRsXjlDBIExOQJpUYT1tf0Ikcptvv5qMn6KV6GUISy... |
Rave#7710: @Chloe von Einzbern looks fine to me
Chloe von Einzbern#0001: you dont see the stutterings ?!
Rave#7710: I think that might just be heaven in itself, is it like that while actually gaming?
Chloe von Einzbern#0001: it lags yes thats why thought of overclock to make it stable
Callum#1368: wut
Callum#1368: lol
... |
L456Tango64D#4361: @yosarianilives I don't know, I messed with LOD, but I'm not smart on the other rivatuner settings
yosarianilives#1841: Me neither, lol
yosarianilives#1841: And cpu maxed right?
L456Tango64D#4361: Yeah 5.2, no HT
yosarianilives#1841: Hmm
yosarianilives#1841: I had mine at like 5.8
yosarianilives#184... |
yosarianilives#1841: Then I fucked up the delid and killed the gpu
hvilepute#5539: Hi! Using the msi afterburner voltage curve to undervolt and oc my card, it seems to always run slightly below the desired mhz, even if I manage to run at considerably higher frequencies at the same voltage, it always goes ~10 mhz below?... |
Callum#1368: i've got a 1070ti evga sc
Callum#1368: @Conmega
Conmega#3813: mighttt have to change the skin on afterburner?
Conmega#3813: http://www.tomshardware.com/reviews/nvidia-geforce-gtx-1070-ti-8gb,5311-18.html
Conmega#3813: you can't change the voltage
Conmega#3813: only the power limit
bean#8086: So I managed t... |
Armin#3486: Wait...5000?
Armin#3486: That's stock for a 1080?
bean#8086: Idk, that’s what precision said. Could be wrong, going by memory
Conmega#3813: try pressing apply?
Armin#3486: Fire up GPU-Z or MSI AB
bean#8086: AB and gpuz were in agreement
Conmega#3813: that your running stock?
Armin#3486: And displayed what?
... |
Conmega#3813: you'd see like 1500 then
Conmega#3813: sorry 1251
Conmega#3813: https://cdn.discordapp.com/attachments/305981966292090881/396301163034574848/unknown.png
Conmega#3813: basically
Conmega#3813: precisionX gives you 5000
Conmega#3813: stock
Conmega#3813: which is half of that "effective" speed
Conmega#3813: ... |
Fallen#0811: too lazy to download it
Armin#3486: What he's saying is that Kombustor is Furmark with an MSI logo
Rave#7710: that is furmark
Armin#3486: Which is shit
Armin#3486: 😃
Jace#4785: anybody managed to stick an Evga 280 CLC onto a 1080 ti?
Jace#4785: Asus turbo in this case
Chloe von Einzbern#0001: i cant even ... |
Armin#3486: 2.1 GHz is pretty high, not all cards will reach tha and if yours already boosts to 2000 by default then you're not gonna get much more out of it
Chloe von Einzbern#0001: i see
Chloe von Einzbern#0001: so auto oc is beter than manualy ?
Chloe von Einzbern#0001: bcuz if i manualy oc i see the mhs going up an... |
Conmega#3813: no load
Conmega#3813: its AT what its set to
Conmega#3813: https://cdn.discordapp.com/attachments/305981966292090881/396677420243222528/unknown.png
Conmega#3813: so thats... weird
nasaug#1506: Why is MSI Afterburner recommended over other GPU overclocking software?
Rave#7710: cos it's generally pretty go... |
Niobium#6334: But using vendor-specific software will also be necessary for accessing things like RGB control on many cards
Jokot#9771: trixx is my amd go to and afterburner/nvidia inspector for nvidia
Rave#7710: yeah ab tends to be somewhat restrictive on amd cards
nasaug#1506: Ah, thanks for the explanation. Another ... |
Deleted User#0000: i dont see any artifacting whatsoever and the temps are in check while im playing
Cameron#9811: Unstable on core most likely
Cameron#9811: could try raising power limits or voltage but easiest solution is to just downclock
Deleted User#0000: my power limit and voltage are already maxed
Deleted User#0... |
whiteshark#1560: values go from -3 to 3
whiteshark#1560: am i doing it wrong?
pkkshadow#5844: you can change it to whatever
whiteshark#1560: oh
whiteshark#1560: thanks
whiteshark#1560: looks the same, scores the same
pkkshadow#5844: that's the problem i had
pkkshadow#5844: opengl was different tho
whiteshark#1560: any ... |
whiteshark#1560: 11
Niobium#6334: 3DM11?
Niobium#6334: Replay_Mode_All should work too
whiteshark#1560: yes 3d11
whiteshark#1560: does it matter which or are all that work the same?
Niobium#6334: Should be a fairly significant impact on the score
Niobium#6334: Is SGSSAA helping the score at all? Because on modern NV s... |
whiteshark#1560: should i test it on the 1030 ?
pkkshadow#5844: sure
Deleted User#0000: youre on a 970?
Deleted User#0000: what do you have for core clock and memory clock?
whiteshark#1560: not anymore
whiteshark#1560: 1430 core
Deleted User#0000: nice
whiteshark#1560: card can do more but the vrm cant
Deleted User#00... |
Deleted User#0000: during heaven it goes to 73c
Deleted User#0000: normal gaming about 69
Deleted User#0000: 1334mhz gpu clock, 1473 boost
whiteshark#1560: i assume its limited by power limit?
Deleted User#0000: more like core voltage
Deleted User#0000: dont think theres a way to increase it without flashing a new bios... |
whiteshark#1560: yes its what gpu-z reads
Deleted User#0000: how do you know how much it pulls?
Deleted User#0000: im an amateur at this lol
whiteshark#1560: you have gpu-z?
Deleted User#0000: yeah
whiteshark#1560: looks at the TDP sensor
whiteshark#1560: you be in %
whiteshark#1560: and than if youknow what the tdp of... |
whiteshark#1560: yes#
Deleted User#0000: i see
Deleted User#0000: im pulling a maximum of 388w at peak load already
Deleted User#0000: with a 500w psu
Deleted User#0000: good idea to flash and try for more or no?
whiteshark#1560: thats your call really
Deleted User#0000: hmm
Deleted User#0000: since this is a second ha... |
Deleted User#0000: 325?
whiteshark#1560: mount a custom cooler
Deleted User#0000: you said 275
whiteshark#1560: and set + 150 offset
whiteshark#1560: 325 is the limit
whiteshark#1560: 275 is what its drawing
whiteshark#1560: it cant actually do 325
Deleted User#0000: oh i see
whiteshark#1560: i just choose a value that... |
Deleted User#0000: i dont think its a problem with nvidia cards until like 80c - 90c or so
Deleted User#0000: and i dont think i could reach that playing the average title
whiteshark#1560: do you have more room on the fan speed?
Deleted User#0000: i dont think it even hits the maximum fan speed in heaven
Deleted User#0... |
whiteshark#1560: yes
Deleted User#0000: where do you get to set that?
Deleted User#0000: when you install the bios?
whiteshark#1560: you extract the bios with gpu-z or nvflash
whiteshark#1560: than you edit it with maxwell bios editor
whiteshark#1560: thats where you set it
whiteshark#1560: and then you flash it on the... |
whiteshark#1560: that way its only higher if you move the slider
whiteshark#1560: if you keep it at 120% it will be the same as it was
Deleted User#0000: the 6+2 (8 pin) provides 150w right?
Deleted User#0000: how much does the pcie slot provide?
Deleted User#0000: 150w + 75w = 225w maximum
whiteshark#1560: by spec slo... |
Callum#1368: i understand, its using more than 100% of its original tdp
Callum#1368: correct?
Armin#3486: Yes
Callum#1368: okay, no worries thanks for help
Armin#3486: Mine's technically using 130%ish 🤷
Callum#1368: what does pascal die at btw
Armin#3486: What do you mean?
Mickulty#1560: pascal is very, very difficult... |
Callum#1368: mines at 67-8
Mickulty#1560: yeah no worries at all at that temp
Callum#1368: one quick q
Callum#1368: set the priority to thermal target or power target
Callum#1368: ?
Callum#1368: since its never gonna hit the power target it makes more sense
Callum#1368: since then it won't throttle
Armin#3486: Referenc... |
Callum#1368: i went for +500 and its fine
Armin#3486: Then go further
Callum#1368: oof
Armin#3486: Until you see performance degradation or artifacts 🤷
Callum#1368: someone said something about
Callum#1368: the 1070 ti being memory limited
Callum#1368: set the priority to thermal target or power target since its never... |
Callum#1368: :(
Fallen#0811: Pretty hard indeed
Callum#1368: @Fallen yeah well
Callum#1368: no image was displayed.
Callum#1368: for about 8 boots
Callum#1368: https://cdn.discordapp.com/attachments/305981966292090881/397008296487157760/unknown.png
Callum#1368: how does this look
Callum#1368: I though you were meant t... |
Callum#1368: nope?
Valkrys#8394: Gpu overclocking through software is super safe short of using trixxx on certain amd cards. Or modding shit.
Callum#1368: why did yu ask if i had samsung memory
Valkrys#8394: Without Samsung memory, you're gonna have a hard time getting an extra 500mhz out of your memory
Valkrys#8394: Y... |
Valkrys#8394: But gddr is 4:1 effective:actual clock.
Callum#1368: temps are a bit toasty
Callum#1368: so?
Callum#1368: my actual clock is 4x4551
Valkrys#8394: No.
Valkrys#8394: Actual clock is 1/2 of 4551
Valkrys#8394: Effective clock is 2x4551.
Callum#1368: thought it was double
Callum#1368: whats difference between ... |
Valkrys#8394: So you can get effectively get 4 cycles per 1 hz.
Callum#1368: so it works at 9.5k mhz
Valkrys#8394: It would be 9100.5
Valkrys#8394: Er 9102
Valkrys#8394: You shouldn't be memory limited with that.
Callum#1368: good.
Valkrys#8394: It's just something that's good to be aware of.
Callum#1368: i went with +... |
Callum#1368: and about 150mhz vs 175mhz offset
Callum#1368: both had same real life clock speed
Valkrys#8394: Yeah, because the card is either thermal or power throttling.
Callum#1368: its the 50mhz thermal throttle
Callum#1368: you know in pascal
Valkrys#8394: It's not enough to worry about tbh.
Callum#1368: my cardd ... |
Valkrys#8394: It helps mostly with minimums, that's what the memory helps the most.
Valkrys#8394: Helps smooth things out.
Mickulty#1560: iirc you have an instruction clock and a data clock
Mickulty#1560: with normal ddr they're equal
Mickulty#1560: and data rate is 2x both
Mickulty#1560: with gddr5 data clock is 2x in... |
Fallen#0811: ...
Fallen#0811: Just do it,
Frito#0907: no
Callum#1368: i did it pussy
Frito#0907: https://cdn.discordapp.com/attachments/305981966292090881/397045423363063822/vfapply.jpg
Callum#1368: looks kinda freeeeeeeeeky
Frito#0907: it should look like that
Callum#1368: https://cdn.discordapp.com/attachments/3059... |
Callum#1368: ¯\_(ツ)_/¯
Fallen#0811: I can get stable 2126 at 1075 mv, and then 1093 mv I get 2142 stable
Callum#1368: noob
Fallen#0811: Hmm?
Fallen#0811: Sure I am, novice.
Callum#1368: should I have onscreen display on? Frito
Callum#1368: its only at 2050
Callum#1368: wtf
Callum#1368: but it says 2075
Fallen#0811: Tha... |
Frito#0907: unlock voltage control/monitoring
Fallen#0811: And restart.
Fallen#0811: Msi after burner
Callum#1368: should i click force constant voltage?
Callum#1368: okay, so with that, the clock went down and the temps went up
Callum#1368: nice
Frito#0907: no dont select that
Frito#0907: just unlock voltage control >... |
Callum#1368: on 1075mv
Fallen#0811: Or he’s running the benchmark
Frito#0907: yeah could be
Callum#1368: naw it isn't that
Callum#1368: i fucked up it was my fault
Callum#1368: all fixed but now it says the
Frito#0907: but yeah you gotta find your cards happy place with voltage and temps for max freq
Callum#1368: now ... |
Callum#1368: assuming you had bios mod and all that shit
Frito#0907: yes
Callum#1368: power delivered
Callum#1368: so its pretty much golden arch?
Fallen#0811: I need to blow out my cooler for my 1060, that shit is fuckin disgusting
Frito#0907: my card will run whatever i set it to 24/7
Frito#0907: and never change vol... |
Callum#1368: now its +200 to get to 2050
Frito#0907: offset doesn't matter
Callum#1368: it that because the curve accounts for gpu boost being pissy
Frito#0907: no
Callum#1368: oh, clocks dropped
Callum#1368: 2062.
Frito#0907: it just doesn't matter its meaningless
Callum#1368: i think thats because its quite hot
Frito... |
Frito#0907: your in the custom curve window
Callum#1368: HOLY SHIT
Callum#1368: screen just went purple and shit
Callum#1368: but now its back 😉
Fallen#0811: Ur unstable
Callum#1368: somethings wrong
Fallen#0811: Lower the clocks
Callum#1368: naw
Callum#1368: the clocks just jumped to 2.1
Callum#1368: even though i've... |
Callum#1368: oh shit i know
Callum#1368: how to raise the voltage now
Callum#1368: yeah well it was freezing and siezing up and shit
Callum#1368: @Fallen Heaven is nice and all, but how long do I have to watch it for
Fallen#0811: The entire time,
Callum#1368: no theres something 100% wrong
Fallen#0811: Or wait until it... |
Callum#1368: its jumping
Callum#1368: i think gpuboost is being gay
Callum#1368: basically, its like freezing going down to 1607 then its going up to 2050
Callum#1368: https://cdn.discordapp.com/attachments/305981966292090881/397049195548377108/unknown.png
Fallen#0811: Or your memory finally decided to fuck itself.
Ca... |
Callum#1368: dw
Fallen#0811: He already focus on mem
Callum#1368: 550 is fine
Callum#1368: i tried +1000 mem
Fallen#0811: It’s just his core seems to have ran it unstable apparently.
Fallen#0811: So lower it by 25mhz, and continue with the core.
Callum#1368: this curve has fucked up the oc
Callum#1368: it used to run f... |
Fallen#0811: Ask frito some of this, I need to go make breakfast.
Callum#1368: he's gone
Callum#1368: :riotping:
Callum#1368: enjoy breakfast
Fallen#0811: @Armin your my replacement.
Fallen#0811: Thanks
Armin#3486: No time 😛
Callum#1368: 😦
Armin#3486: Need to make food and shit
Callum#1368: welp
Callum#1368: any quic... |
Callum#1368: and how do you guys set custom fan curves
Fallen#0811: It’s time to figure things out without a stupid hand that seems retarded at times to guide you.
Fallen#0811: Just hit that cog next to the fan speed
Fallen#0811: It’s small
Fallen#0811: Right next to it
Callum#1368: but then it just drags slider
Callum... |
Callum#1368: is being retarded
Frito#0907: your running at 70c
Frito#0907: lmao
Callum#1368: whats wong with 70c
Callum#1368: its hot
Callum#1368: i know but
Fallen#0811: Bruh, my mini card runs at 85+
Frito#0907: boost 3.0 doesn't like to play nice at 70c +
Frito#0907: crank that fan to the max
Frito#0907: or run the ... |
Frito#0907: boost 3.0 takes two things into account
Callum#1368: and went purple screen
Callum#1368: purples my fav colour
Frito#0907: temperature
Frito#0907: and power limit
Frito#0907: as temps go up it wants to reduce voltage strap
Frito#0907: to stop the temp rise
Callum#1368: so bnasiclly
Callum#1368: gpu boost su... |
Callum#1368: it doesn't matter. okay
Frito#0907: what matters is where your card is staying clock wise *real clocks*
Callum#1368: its pinned around 2037
Callum#1368: i lowered the curve by 5mhz
Frito#0907: yeah
Frito#0907: i mean without better cooling thats probably all your card can do
Callum#1368: its a nice 10% imp... |
Frito#0907: 2100 all day long +/- 14 mhz
Frito#0907: thats also with liquid metal on the die too though at that point
Frito#0907: then flashed no power limit bios to my card + gives me 1.2v max instead of 1092 mv
Callum#1368: which means
Callum#1368: you run 2152
Frito#0907: because i would power limit past 1075 normal... |
Fallen#0811: Wait frito
Fallen#0811: How did you flash the bios onto a pascal card?
Frito#0907: its a leaked bios from asus
Callum#1368: xd asus
Callum#1368: noobs
Frito#0907: only 1080 and 1080 ti's have leaked bios's with no power limits
Frito#0907: because asus made them for strix cards at an extreme oc event
Frito#... |
pkkshadow#5844: i had to do a bios mod to get above 25% on my rx 470.
Frito#0907: you can callum
Frito#0907: but if your card starts hot
Callum#1368: yeah ive got it 40% fan at idle
Frito#0907: its going to end up hotter under load
Callum#1368: and then that keeps it under 50 😉
Frito#0907: like mine it idles at ambien... |
Callum#1368: then starts climbing every so slowly
Callum#1368: up to 70 odd
Frito#0907: yeah because the heatsink/fan cannot remove the heat fast enough so its slowly rises
Fallen#0811: After today I’m cleaning my gpu up
Callum#1368: surely guys over here must have free cooling loops going spare 😉 Xd
Fallen#0811: Beca... |
Callum#1368: how do you unpause heaven lol
Frito#0907: heaven doesn'
Frito#0907: tpause
Frito#0907: lol
Callum#1368: well it paused
Frito#0907: prolly crashed
Callum#1368: still animated
Frito#0907: idk close it and reopen
Callum#1368: BOOST IS AT 2062 why the fuck is it doing that
Callum#1368: fck boost
Callum#1368: d... |
Callum#1368: little jump there
Callum#1368: @Frito if it jumped once in heaven and is fine outside of stress tests, e.g games then its a solid stable oc?
Callum#1368: ive managedd to keep temps low enough to keep temps in the very low 70's
Frito#0907: you have to just try it and find out
Frito#0907: loads on gpu can ch... |
Callum#1368: because thats my original plan
Callum#1368: and whats the power limit default? 0% or 100%
Frito#0907: yeah everything is safe to do
Frito#0907: without modding a card nothing can hurt it
Frito#0907: 100 is default
Callum#1368: @Frito One other thing is the fact that I can't make fan profiles attatched to a... |
buildzoid#6254: on pascal
Frito#0907: yeah should do fuck all on cards with normal bios's
buildzoid#6254: the voltage will just bounce between 1V and 1.09V depending on what boost feel like
Frito#0907: if you have a strix xoc bios flashed it will open up allowing you to adjust V/F curve to 1.2v
Frito#0907: and actually... |
Frito#0907: yeah that way but even then
Frito#0907: have to dupe the driver like we're doing on the 1030's
Frito#0907: we set a completely flat v/f curve and it flips out
Frito#0907: lol
Niobium#6334: I've spent the entire day working on getting the 1030 to cooperate. It's exhausting.
Mickulty#1560: :petersen:
Frito#0... |
Frito#0907: haha
Frito#0907: mega obvious though
Niobium#6334: Yeah, just need to look at the subtests
Niobium#6334: e.g. this one's valid https://cdn.discordapp.com/attachments/305981966292090881/397163592476262402/87488.PNG
Niobium#6334: Not completely happy with how it's doing on air, but I'm going to give one of th... |
E30Tom#3276: I struggle to believe the OS has that much of an effect on score results
buildzoid#6254: have you check any monitoring utility about your GPU?
E30Tom#3276: https://cdn.discordapp.com/attachments/305981966292090881/397472038127665154/unknown.png
E30Tom#3276: thats the usage
Niobium#6334: It's the physics s... |
E30Tom#3276: this alright? https://cdn.discordapp.com/attachments/305981966292090881/397472616413396999/unknown.png
E30Tom#3276: AH HA.
E30Tom#3276: so wait my CPU could be over heating?
E30Tom#3276: because my corsair h55 has been clicking and making weird noises for about a year
E30Tom#3276: or two
Conmega#3813: uhhh... |
E30Tom#3276: like the noise
buildzoid#6254: download a temp monitoring tool like HWinfo and send us a screenshot
E30Tom#3276: gotcha, two secs
E30Tom#3276: https://cdn.discordapp.com/attachments/305981966292090881/397474071433969674/unknown.png
E30Tom#3276: thats with steam, discord and documents open
Armin#3486: Leav... |
Armin#3486: We need something that loads your CPU
E30Tom#3276: arma 2
E30Tom#3276: lol
E30Tom#3276: im going to use intel burn test
Conmega#3813: intel burn test or prime95 yea
E30Tom#3276: https://cdn.discordapp.com/attachments/305981966292090881/397477983092211712/unknown.png
Rave#7710: ok, what's the temps like?
E3... |
E30Tom#3276: https://cdn.discordapp.com/attachments/305981966292090881/397479453904863259/unknown.png
Rave#7710: hmm so that's all fine
Rave#7710: so it's most likely something bios related then
E30Tom#3276: right, bios time
Rave#7710: i'd go ahead and load optimised defaults and see what happens from there
E30Tom#327... |
E30Tom#3276: Right lets see
E30Tom#3276: https://cdn.discordapp.com/attachments/305981966292090881/397481580974702593/unknown.png
E30Tom#3276: so my cores are like
E30Tom#3276: flashing in random orders
E30Tom#3276: yellow and green
E30Tom#3276: VID voltage is going from 0.7220 to 1.06 every second
Rave#7710: yeah tha... |
E30Tom#3276: at full whack
E30Tom#3276: hm. only says i have 813mb of RAM available unless its stressing it idk
E30Tom#3276: https://cdn.discordapp.com/attachments/305981966292090881/397483581586276372/unknown.png
E30Tom#3276: okay, its all normal. Time to do a benchmark.
E30Tom#3276: woo!
E30Tom#3276: https://www.3dm... |
Armin#3486: Nice
Armin#3486: Delta-oldschool
Frito#0907: ahh yis this heatsink works MUCH better than the stock alum garbage
Armin#3486: Lol
Frito#0907: that monster fan did nothing to help the stock heatsink
Frito#0907: still ran just as hot
Armin#3486: Probably the alu limiting
Frito#0907: well not just that
Frito#09... |
Frito#0907: lmao
Armin#3486: Lel
Frito#0907: throw some conductonaut on this bitch and i'll be even cooler hehe
Armin#3486: FUCK
Armin#3486: You just reminded me
Armin#3486: I only used Kryonatu on the E8400
Frito#0907: look at this garbage
Frito#0907: https://cdn.discordapp.com/attachments/305981966292090881/39753722... |
Jace#4785: is the 1080 ti strix pcb worth anything more than the founders pcb?
Mickulty#1560: iirc the 1080ti FE actually has a pretty good PCB
buildzoid#6254: but it's still worse than the Strix PCB
buildzoid#6254: the Strix has XOC support
Frito#0907: Jace isn't going to be sticking it on ln2 he's just looking to get... |
Rave#7710: it's just the 4 spring loaded screws round the core itself that you need to get at the gpu core itself
Cruzix#0494: Which software is used to test if a GPU OC is stable?
Cruzix#0494: Looking to OC my RX 580 4gb, first time OCing tho
Alcyone#2233: @Cruzix I start with Heaven/Valley then just play some games. ... |
Mickulty#1560: stock cooler should be fine
Jace#4785: yea but won't be undervolting in sli lol
Mickulty#1560: any aftermarket air cooler will be big, like 3+ slots
Mickulty#1560: there are plenty of good waterblocks though
Jace#4785: budget of $100 or so
Jace#4785: already planning on an accelero iv, any other options?... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.