data stringlengths 14 24.3k |
|---|
∫ntegral#0450: oh i think i recall that
∫ntegral#0450: https://cdn.wccftech.com/wp-content/uploads/2016/07/AMD-Radeon-RX-480-4GB-Surprise-8GB.jpg
Betrayed#3582: Oh the RX480 🤦
∫ntegral#0450: there was also a meme with the 970 3.5gb
Betrayed#3582: Yeah but the 970 wasn't a software lock
Resune#9806: my 970 and I have a... |
It crashed at 1874....
q3w3e3#2821: Damn... Can't ge tover 1800 again.
q3w3e3#2821: My gpu just read 1090W
q3w3e3#2821: Lmao
q3w3e3#2821: https://cdn.discordapp.com/attachments/305981966292090881/549831314031771651/IMG_20190226_005308.jpg
q3w3e3#2821: 221w with +0 on the power limit.
q3w3e3#2821: 256 is the most it'll... |
Fitz#8200: double what afterburner says
Naeno#0001: Is that just a thing with afterburner and would I double what it shows on other cards too like a 2070
Naeno#0001: Or is it something to do with a 1060
Fitz#8200: its DDR
Fitz#8200: runs in dual channel, so you get an effective double the bandwidth
Naeno#0001: okay tha... |
ansuex#4434: I received my Gigabyte RTX2070 Windforce yesterday
ansuex#4434: is it safe to overclock it?
ansuex#4434: And better to use MSI Afterburner or Gigabyte their own software tool?
ansuex#4434: AORUS ENGINE
buildzoid#6254: use afterburner or EVGA precision
ansuex#4434: does that EVGA precision work with other b... |
Caches#8539: also you always want your power limit at the maximum % you can
Caches#8539: is the easiest way to get performance
Caches#8539: my 2070 goes to 2050mhz max if you want a benchmark, I think that is kind of on the lower end of 2070s
Caches#8539: you do need a 400a chip to get over 1900 though
Caches#8539: in ... |
pkkshadow#5844: because on air you should not go above 1.25v and temps should stay below 60c ish
pkkshadow#5844: above 60c i've noticed my card downclocks.
(that was before i modified the bios mind you, i haven't tested it a whole lot since. and that was the stock bios)
Deleted User#0000: well my gpu wasnt able to be u... |
Battlefield_Ace#9175: ok. u do have a dual bios card. would you want to look into bios modding?
punkrr#0009: sure
punkrr#0009: lol
punkrr#0009: i did hear that modding the timings helps a lot
punkrr#0009: or something like that
Battlefield_Ace#9175: i can support that
Battlefield_Ace#9175: got me to #1 in my hardware c... |
punkrr#0009: https://cdn.discordapp.com/attachments/305981966292090881/550355651294134294/Ellesmere.rom
Battlefield_Ace#9175: here. i did the memory timings, adjusted the power limit, added 50mv onto the memory. dont try 2250 immediately tho. chances are u wont be able to run it. however, i saw better results at 2100 ... |
punkrr#0009: so i just flash with with atiwinflash, any other steps? @Battlefield_Ace
Battlefield_Ace#9175: that should be it
punkrr#0009: my screen is gray
Battlefield_Ace#9175: after flashing?
punkrr#0009: yeah
Battlefield_Ace#9175: restart?
punkrr#0009: kk
punkrr#0009: how do i know if the new bios flashed properly?... |
Battlefield_Ace#9175: well u could save the bios again thru gpu-z and have me look at it. i could tell u if it took
Battlefield_Ace#9175: unfortunately i cant rly verify any other way. u can in theory change the version string of the bios, but htis version of atiwinflash freaks out if u do that
punkrr#0009: https://cd... |
Battlefield_Ace#9175: whats that for?
pkkshadow#5844: when you have a custom bios on polaris, you have to use the patcher
pkkshadow#5844: if you don't, the gpu may not show up when you reboot into windows
Battlefield_Ace#9175: no u dont. i didnt have to
pkkshadow#5844: it depends on the display driver version
pkkshadow... |
pkkshadow#5844: patch takes like a minute
pkkshadow#5844: so why not
NuclearDebris#1984: ^
whiteshark#1560: that does not suprise me
punkrr#0009: do i need to run patcher as an admin
pkkshadow#5844: probably.
NuclearDebris#1984: Yeah I didnt know how different they were PCB wise, but I have the gaming x bios now for th... |
punkrr#0009: ok i literally cant use my start menu anymore
pkkshadow#5844: ctl+shit+esc brings up task manager, close explorer.exe
file> new task> explorer.exe
pkkshadow#5844: try that
punkrr#0009: i can get into my file explorer by double clicking a folder on my desktop and stuff
punkrr#0009: but its literally just my... |
though that probs won't help
Battlefield_Ace#9175: not sure if it will fix it, but its worth a try
punkrr#0009: where is wattman?
punkrr#0009: ive never used it
punkrr#0009: i tried restarting explorer.exe
adi769#6854: @NuclearDebris did you swap your 1080ti somehow for a gaming x? and have you oc'd it yet?
Battlefield... |
NuclearDebris#1984: Grr
adi769#6854: huh, what does it do?
NuclearDebris#1984: Make your GPU always at boost clocks
NuclearDebris#1984: It's useful for certain benches
punkrr#0009: https://cdn.discordapp.com/attachments/305981966292090881/550372944845602836/Ellesmere3.rom
punkrr#0009: @Battlefield_Ace
punkrr#0009: im ... |
punkrr#0009: gonna try flashing the backup
Battlefield_Ace#9175: try reinstalling the drivers first
punkrr#0009: alright
punkrr#0009: should i DDU and all that
Battlefield_Ace#9175: nah, itll probs be ok. just do a clean install
Battlefield_Ace#9175: afaik 19.2.3 is a beta driver. that might be the issue
punkrr#0009: m... |
punkrr#0009: sure one sec
punkrr#0009: have to re do monitor overclock reee
Battlefield_Ace#9175: what did u get ur monitor to?
punkrr#0009: 75hz but its not a real OC
punkrr#0009: the monitor supports up to 75hz but for some reason you can only pick up to 60hz in windows
Battlefield_Ace#9175: @NuclearDebris is there n... |
NuclearDebris#1984: all it does is make your 3D clock always active
4a61636b#5675: That would probably be why my card gets angry with K
NuclearDebris#1984: or boost clock I guess
NuclearDebris#1984: yeah you would need to add the +100mv on pascal, plus that increases your boost anyway
punkrr#0009: isnt k boost the equi... |
NuclearDebris#1984: it could also give better fps in games, havent tested that part yet
4a61636b#5675: Clock are there any benches that are primarily GPU based?
NuclearDebris#1984: Yes
Battlefield_Ace#9175: yes
Battlefield_Ace#9175: all the unigines, all the 3dmarks
NuclearDebris#1984: FSU, gpupi, FSE kinda, any bench ... |
punkrr#0009: same afterburner settings, 1450 core and 2100 memory
punkrr#0009: gonna try 2250 memory now
Battlefield_Ace#9175: yeah thats what i mean
Battlefield_Ace#9175: u wont be able to run 2250 mem any more
punkrr#0009: oh ok
punkrr#0009: should i leave it at 2100?
Battlefield_Ace#9175: u could try increments of, ... |
Battlefield_Ace#9175: 😄
Battlefield_Ace#9175: but at this point it doesnt rly matter how much better u can make it, its already better 😛
punkrr#0009: 1450-1460 is about as high as i can push at 1.175v, i could probably try like 1.8-19 but it's probably not even worth the effort lol
Battlefield_Ace#9175: u mean 1.18/1... |
adi769#6854: that'd be like 9600mhz?
4a61636b#5675: 94 but yeah
4a61636b#5675: Wild shit
4a61636b#5675: My real clock or whatever you call it is 8828
4a61636b#5675: Almost 9
4a61636b#5675: What can your micron do?
adi769#6854: it seems to do +500 stable now (previously it wasn't a fan of it in some games and did 450 bu... |
hold on I might check in a sec
Battlefield_Ace#9175: @adi769 it's "next gen". oh wait.....
Battlefield_Ace#9175: @4a61636b i got +860 on my 1050ti
4a61636b#5675: Micron?
Battlefield_Ace#9175: then my psu blew up...
Battlefield_Ace#9175: no idea
Battlefield_Ace#9175: never checked
4a61636b#5675: It was probably samsung
... |
@Battlefield_Ace oh did i mention the cooler on this thing sounds like a jet engine past like 75% fan speed
Battlefield_Ace#9175: lol. what case is that?
punkrr#0009: x qpack3
punkrr#0009: i like it but its kinda on the offbrand cheapo side, was like $60
punkrr#0009: only not super expensive matx case i could find with... |
adi769#6854: Furmark is more just to torture your card heat wise and it may or may not be accurate (since it may downclock)
ansuex#4434: Im running heaven and it does fine
4a61636b#5675: I run 3dm11
adi769#6854: if heaven is putting it to 100% and not getting CPU bottlenecked then that's fine
4a61636b#5675: Holy shit I... |
Caches#8539: For 2070 average is 2050-80 core?
Caches#8539: I can't go over 2050 that's for sure
Betrayed#3582: uh is this a pre binned chip?
ansuex#4434: hmm
ansuex#4434: It fluctuates between 1995 and 2085
ansuex#4434: is that a bad sign?
ansuex#4434: nothing pre binned, im new to this :p
adi769#6854: I've not person... |
DaddySpaghetti#1199: Yea that’s sometimes a driver crash
ansuex#4434: and if heaven crashes in general?
DaddySpaghetti#1199: It’s unstable for sure
ansuex#4434: oke oke 😃
4a61636b#5675: My 1070 does 2136 stable
ansuex#4434: thats higher then my rtx2070 jack!
4a61636b#5675: :D
adi769#6854: ~~I won't steal your fame~~
|... |
4a61636b#5675: Was your 2151 on water?
adi769#6854: yeah
4a61636b#5675: You never tried it on air?
adi769#6854: I thought I had 2200 in my pockets but it got angery
adi769#6854: on air I could only do 2050
4a61636b#5675: Oh shiiiiiet
4a61636b#5675: What card?
adi769#6854: 1070 amp extreme
adi769#6854: stock it did 2037... |
4a61636b#5675: I love it, fans are quiet to the point where I can game on 60% and not really notice it
adi769#6854: I don't do quiet xD
4a61636b#5675: 😂
4a61636b#5675: Was it you that said your 1070 was micron?
adi769#6854: yea
4a61636b#5675: Give me your mem its better
4a61636b#5675: Mine gets angry after 410
adi769#... |
ansuex#4434: should I then test it in games like assassins creed?
adi769#6854: I hope it lasts or 2+ years because I want to stop myself from throwing money at graphics... I barely utilise it as is lol
ansuex#4434: higher core made my heaven hang/crash
adi769#6854: have you oc'd your mem?
ansuex#4434: yeah
adi769#6854:... |
ansuex#4434: but for me to make sure its stable
ansuex#4434: the only way is to compare?
adi769#6854: well once you're reaching the point of artifacting/crashing cause of memory you're probably already losing performance
ansuex#4434: Ah yeah it makes sense then
ansuex#4434: thanks for your help, I'm going to continue t... |
[ʞR] Otroud#7943: bf5
[ʞR] Otroud#7943: and survival games
Battlefield_Ace#9175: ud have to test. id depends how well bfv scales in sli. id just get the 2070 instead of 2x1070 imho
[ʞR] Otroud#7943: ah k
[ʞR] Otroud#7943: well i can get 1070 atm for 200 each
Battlefield_Ace#9175: @adi769 i mean....1575 on polaris on ai... |
adi769#6854: you're actually lucky with GPUs from the looks of it
Battlefield_Ace#9175: well....with gpu silicon lottery maybe....with general pc hardware maybe not.....the fact remains that a psu failure took out my entire system
Battlefield_Ace#9175: i should actually test if that card rly is dead. it probably is, bu... |
adi769#6854: https://cdn.discordapp.com/attachments/305981966292090881/550474789777833984/unknown.png
Alcyone#2233: 103 pfft. (not real) https://cdn.discordapp.com/attachments/305981966292090881/550486884359340033/we_did_it.png
adi769#6854: haha
adi769#6854: that 103c was without throttling
DaGunzi#1241: does it get r... |
∫ntegral#0450: https://cdn.discordapp.com/attachments/305981966292090881/550551998945034250/312.png
Kif_Kroker1729#0350: @q3w3e3 27701
q3w3e3#2821: Yeaahhhhhh
q3w3e3#2821: my firestrike runs (long ago before it threw the liquid bios on the card) were at subzero ambients and i still broke 60 degrees....
q3w3e3#2821: g... |
andrewcandoall#0853: Hey
andrewcandoall#0853: What happens when you run a game while you set an msi profile
andrewcandoall#0853: Apply it I mean
q3w3e3#2821: Should be fine, might stutter momentarily(?)
worst comes to worst you have to reset graphics drivers (shift + ctrl + win + b)
andrewcandoall#0853: So that's norm... |
andrewcandoall#0853: So if I have it in bios it's better right
andrewcandoall#0853: https://cdn.discordapp.com/attachments/305981966292090881/550581822887559168/20190227_114320.jpg
andrewcandoall#0853: Just got these
q3w3e3#2821: Noice!
andrewcandoall#0853: Im using a prebuilt mobo rn
andrewcandoall#0853: And I got th... |
andrewcandoall#0853: I think it might just be afterburner
q3w3e3#2821: I dunno what my mem is... hmmm...
q3w3e3#2821: I have never had my VRM temps get to anythign worying, only thing would be heat soak to die but thatd be tiny in comparison to the heat put out by the die...
PhantomGaming27249#6489: i have read mixed t... |
q3w3e3#2821: ooooh...
PhantomGaming27249#6489: i would say 1.4 though for daily
PhantomGaming27249#6489: cause there is some randomness with it
PhantomGaming27249#6489: but generally speaking 1.5 is ok for b die
PhantomGaming27249#6489: but less voltage for daily use is better
PhantomGaming27249#6489: g skill actually ... |
I'll see what I can do with the timings.
PhantomGaming27249#6489: i would try 14 14 14 3200 32 1t
PhantomGaming27249#6489: at 1.4 volts
Deleted User#0000: got a vega 56 coming saturday, anything i should watch out for, and any tips for OCing and Undervolting?
Deleted User#0000: ping me if so, if you wouldnt mind 😄
∫nt... |
ansuex#4434: ?
ansuex#4434: using EVGA Precision
Resune#9806: probably not if you don't know exactly what you're doing
ansuex#4434: yea no I do not :p
ansuex#4434: also tested at default core clock in a heaven benchmark
ansuex#4434: and again with a 100+ on the core
ansuex#4434: and avg and minimum fps went higher
ansu... |
Resune#9806: sure, it's work hours right now for US, should be quite a few people around to help maybe in a few hours
ansuex#4434: Im patient ^^
Resune#9806: well that's good, need to be for overclocking 😄
PhantomGaming27249#6489: anyone here with a red dragon 56 try to get the g12 working on it?
Raudi Raccoon#6691: I... |
pkkshadow#5844: nope.
usually core voltage is for the core only.
pkkshadow#5844: on my rx 470, i only have control over the gpu core voltage through software.
pkkshadow#5844: i can't change the mem voltage
DZCreeper#6471: dumb question, does a locked intel CPU also lock out the iGPU overclocking? I have experimented wi... |
adi769#6854: I have a feeling like they should be about on par with the 980ti having more oc headroom
Raudi Raccoon#6691: Only I would imagine being an issue is my mem speeds maybe? 3066 vs 3000 for ram?
adi769#6854: I don't have a clue tbh, but 3000 vs 3066 is insignificant and even if the timings were much better, I ... |
wrath#4261: So I've noticed that my GPU never uses 100% power, which makes me wonder if that means if it used more it would be able to OC higher? I have voltage maxed on MSI (980TI Classy) and power limit at 141% but it never uses more than like, 85%
wrath#4261: But if I try to push it's clock speeds higher it's unstab... |
wrath#4261: I just ran furmark and it still is only pulling 85% power
Betrayed#3582: increase the core voltage if you want more power draw
wrath#4261: Core is at max my dude
Betrayed#3582: It also may be 85% of the 140% power limit
wrath#4261: No, I tested that
wrath#4261: Because I checked the actual wattage values in... |
Betrayed#3582: Are you hitting any limits?
Betrayed#3582: ie voltage?
wrath#4261: Vrel and VOp
wrath#4261: Which is voltage related but I don't understand why
wrath#4261: Because even on stock I hit those
wrath#4261: I'm switching to my LN2 BIOS really quick to see if it's an issue with my stock BIOS for some reason
wr... |
wrath#4261: even in furmark, a 300w card is only pulling about 270w
wrath#4261: max I should say
wrath#4261: in both of those it was only pulling 250 max
Betrayed#3582: vRel = Reliability. Indicating perf is limited by reliability voltage.
VOp = Operating. Indicating perf is limited by max operating voltage.
There we... |
If its not getting enough voltage it won't be able to step up to the next boost
wrath#4261: I mean I can push it to 1.3v and the power goes to 95% but it doesn't really do anything
wrath#4261: the perfcaps are still there (obv)
wrath#4261: so I just don't understand why last week I only had VRel at these same settings... |
wrath#4261: Yes and it refuses to do that
wrath#4261: but it used to
wrath#4261: but now it just is like no fuck you I'm not drawing more power
Betrayed#3582: uh did you remove the heatsink?
wrath#4261: I've got an AIO on it
Betrayed#3582: You might have failed to get it back on correctly and have a hotspot
wrath#4261:... |
DaddySpaghetti#1199: And you’re at 1080p
DaddySpaghetti#1199: I never go past like 110% until i run a 4K benchmark
wrath#4261: Even at 4k benchmarks it only uses like 90% max
DaddySpaghetti#1199: Cpu bound
DaddySpaghetti#1199: Was cpu sitting at 100%
wrath#4261: No
wrath#4261: Usually around 70-80%
DaddySpaghetti#1199:... |
DaddySpaghetti#1199: Which bios?
wrath#4261: Even while undervolted I'm hitting it
wrath#4261: Stock
Raudi Raccoon#6691: At stock I would see Pwr before I saw vrel
wrath#4261: I have literally never seen power as my perfcap
wrath#4261: @DaddySpaghetti the classified Ln2 and stock bios
wrath#4261: I've tried both, and g... |
DaddySpaghetti#1199: I also don’t look
DaddySpaghetti#1199: It literally can’t use more power because your frequency and voltage are maxed out
wrath#4261: But that's why I'm confused
DaddySpaghetti#1199: Is it affecting your games?
wrath#4261: Because last week I wasn't ever hitting any of these with like 1.23v
wrath#4... |
wrath#4261: So that could be part of it
Betrayed#3582: unstable core
wrath#4261: ?
Betrayed#3582: or unstable memory
Betrayed#3582: both can cause performance drops
wrath#4261: Bruh they were stable and now are not
wrath#4261: Nothing changed
DaddySpaghetti#1199: Degraded?
wrath#4261: I doubt it, I never ran higher tha... |
DaddySpaghetti#1199: too much furmark?
wrath#4261: I've run it thrice since the issue occurred, never before it occurred
wrath#4261: apparently auto correct doesn't think thrice is a word
TurtleMasterFlex#5021: @Raudi Raccoon can I ask why you believe that driver is best? Had done research about specific drivers but ne... |
wrath#4261: @TurtleMasterFlex you messed with my bios, didn't you adjust the voltage tables?
Raudi Raccoon#6691: Maybe, I never got the code 43 with my Gigabyte G1 970
TurtleMasterFlex#5021: Slightly yes
TurtleMasterFlex#5021: Raised the limit in case you could do it, but didn't set a specific locked voltage
Raudi Rac... |
TurtleMasterFlex#5021: I thought you got that 1535 with the power limits removed one
wrath#4261: Yeah I am on stock now
wrath#4261: But this shit just hates me
wrath#4261: I had stable 1545 and 7.9 at those same voltages (but no memory overvolt)
TurtleMasterFlex#5021: I've got 2 more noctua fans im tempted to throw on ... |
wrath#4261: And I have no perfcaps now
wrath#4261: But it's only reporting like 145w of usage
TurtleMasterFlex#5021: These ones did wonders, dropped from mid 60s to 50 and below
DaddySpaghetti#1199: holy shit i ran 1550mhs core
TurtleMasterFlex#5021: And IDK why its doing that I've looked so many times
DaddySpaghetti#1... |
DaddySpaghetti#1199: it was Mr. Dark
DaddySpaghetti#1199: i had him do one with a custom baked in custom fan curve
TurtleMasterFlex#5021: That's pretty easy, just a little math and a few settings
TurtleMasterFlex#5021: I've learned how to mod bios's from doing it with my card extensively
DaddySpaghetti#1199: https://c... |
wrath#4261: Because I went back to an older one and now the only perfcap I have is Vrel
wrath#4261: Still only using like 80% TDP
Raudi Raccoon#6691: It's possible that it was a problem
DaddySpaghetti#1199: probably was, haha
DaddySpaghetti#1199: still
DaddySpaghetti#1199: not gonna use much more power
wrath#4261: Just... |
Raudi Raccoon#6691: Yeah I think so
DaddySpaghetti#1199: should've saved it for benching, oh well
wrath#4261: From my understanding 1500+ was good
wrath#4261: 1475 was like average
wrath#4261: Also I'm running 4k superposition ATM and hitting max of like 102% power usage now
wrath#4261: Though I am thermal throttling t... |
DaddySpaghetti#1199: gotcha
wrath#4261: It was one of the few that worked with this bracket
wrath#4261: And that I could afford
wrath#4261: And since my stock cooler (the ACX2.0) was hitting 86 C under load with max fan speed even after a repaste, I decided fuck it
TurtleMasterFlex#5021: Anything over 1550mhz on the co... |
TurtleMasterFlex#5021: I've got the bios hardwired to 1531, it does not move a single mhz
DaddySpaghetti#1199: mid 40s under water was typical
TurtleMasterFlex#5021: But I'll attempt
TurtleMasterFlex#5021: I'm on air
wrath#4261: Bc something tells me I'm temp limited atm
wrath#4261: Bc adding voltage doesn't make this ... |
wrath#4261: I mean yes
wrath#4261: but that's still temp related
wrath#4261: i.e
wrath#4261: temp limited
wrath#4261: if my temps were lower it would hold the clock
TurtleMasterFlex#5021: Maybe you should try disabling boost like I did
TurtleMasterFlex#5021: It won't drop even as 65c
wrath#4261: we tried that remember?... |
TurtleMasterFlex#5021: I can set something like 1506 and let you raise It from there
TurtleMasterFlex#5021: I'd rather not give you a bios that could insta crash
wrath#4261: Just leave it then and I can adjust it then probably
wrath#4261: @DaddySpaghetti if I put it in a freezer does it count lmao
wrath#4261: Well the ... |
TurtleMasterFlex#5021: 🤔 I'll make sure I didn't touch anything else
TurtleMasterFlex#5021: https://cdn.discordapp.com/attachments/305981966292090881/550899978768220170/ln2mod2.rom
TurtleMasterFlex#5021: try that one out
TurtleMasterFlex#5021: the first one i had just raised the 3d turbo clock to 1506, this time i ma... |
sLing#8554: or sync them
TurtleMasterFlex#5021: Voltage may be different for the same speeds
wrath#4261: I maxed out the voltage slider in AB since it went back to it's stupid basic one
wrath#4261: And it's sitting at 58C without dropping so that's good so far
wrath#4261: And it crashed...
wrath#4261: It isn't working ... |
TurtleMasterFlex#5021: Yeap temps increase with speed especially on gpus
TurtleMasterFlex#5021: Not a whole lot, but they do
adi769#6854: if you have airflow or a heatsink touching thm it's not a worry
adi769#6854: if you don't, from. my experience they can get really warm
adi769#6854: like, on the back of pcb with no ... |
TurtleMasterFlex#5021: From stock to that +1000?
TurtleMasterFlex#5021: Games are the true test
adi769#6854: ^^also make sure you're not hitting ecc
adi769#6854: cause then you loose performance but ont artifact
TurtleMasterFlex#5021: Try superposition or 3dmark time spy
adi769#6854: furmark isn't really accurate in th... |
adi769#6854: no it's not
adi769#6854: I drop 30w from stock and have same performance if I push the memory
adi769#6854: also I typed that up before you even sent that msg about your undervolt so yeah, you can probably tell its worth it if others do it
TwentySix#2665: hello guys, quick question:
TwentySix#2665: i got th... |
Raudi Raccoon#6691: Alright so I'm kinda noticing something with benching Pascal. It's scoring lower than Maxwell but faster in games.?
NovaBandit#2679: Hey everyone. I have an EVGA 2080 ti Black. I've got it stable at ~2000 mhz / 8000 mhz memory. Out of curiosity, I wanted to see what OC Scanner could do, but in EVGA ... |
[ʞR] Otroud#7943: is it possible to OC a gtx 1070 SC from EVGA when i get a custom loop?
Battlefield_Ace#9175: @pkkshadow damn. i was doing it thru bios mods
Callista#3917: you can probably get most of the extra performance you can get out of the card with the air cooler
Callista#3917: it's an acx card right?
Battlefie... |
Battlefield_Ace#9175: well i did get 1575 on my 580 with those settings. i wonder what i could get with actual 1.35v
DZCreeper#6471: you are hitting 1575MHz on air cooling? Morpheus II?
Battlefield_Ace#9175: nah. stock
Battlefield_Ace#9175: sapphire nitro+ cooler
DZCreeper#6471: somebody mislabelled an RX 590 me thinks... |
∫ntegral#0450: i just bumped it up 1 level
∫ntegral#0450: i think i still get an average of 15-20mV of droop
Battlefield_Ace#9175: ill see if that helps.
Battlefield_Ace#9175: im trying to beat my own score https://www.3dmark.com/3dm/33961281.
∫ntegral#0450: 1168mV set in overdriventool https://cdn.discordapp.com/attac... |
metulhed#2973: @Resune seems pretty normal for a 970
metulhed#2973: dug up what my old 290x did, right around there https://cdn.discordapp.com/attachments/305981966292090881/551324393742139422/valley_290x_1200.png
Resune#9806: I'm 1442mhz on the core clock and 1800 on the memory
metulhed#2973: that was 1200mhz core on... |
Resune#9806: fans aren't even at 100% at that temp
metulhed#2973: your card is factory OCd presumably, that's quite good
metulhed#2973: which 970?
Resune#9806: it's a Zotac AMP! Extreme core edition
metulhed#2973: oh nice
metulhed#2973: I just got the 1080ti amp extreme
Resune#9806: yeah around 65% fan speed at 59C
Res... |
Resune#9806: that's why I wanted to see if i couldn't push my card just a tiny bit further
Resune#9806: I'm sure i could get up to maybe 1540mhz
Resune#9806: seems like a good bin on my 970
Food#9417: very good. my poor old 970 could hardly hit 1300. deficiencies of the 1 pin lifestyle
Resune#9806: you're saying i have... |
Resune#9806: Base: 1228 MHz
Boost: 1380 MHz
Resune#9806: for mine
Resune#9806: mine boosts to 1442.3mhz on core and 1800mhz on memory
Resune#9806: 1.206v
Food#9417: yeah overvolting helped me a fair bit but you can only push so much over a 1x8 pin. i assume yours has 2x pins?
Resune#9806: yeah it's a 8 + 4
Resune#9806:... |
Food#9417: yeah its 2x 6pin
Resune#9806: i just thought it was pretty nuts my card goes this far on its own
Resune#9806: obviously custom bios from zotac
Resune#9806: but I've never ever had stability issues
Food#9417: this is what is referred to as
Food#9417: the silicon lottery
Resune#9806: Yeah, but I don't really k... |
∫ntegral#0450: probs 1.25v
∫ntegral#0450: whatever you can set in msi ab is safe
Resune#9806: +87mv
Resune#9806: it's a Zotac card
Resune#9806: right now I'm 1443mhz and 7.2ghz on memory
Resune#9806: with no offsets
Resune#9806: 1.206v
Resune#9806: how should I start tweaking it? core first or memory first
∫ntegral#045... |
Resune#9806: wonky in terms of core clock gain and stability on the clock speed
Resune#9806: With +30 it’s 1455 to 1472
Resune#9806: From 1442 at 0
Resune#9806: Ah that’s because it’s an offset on to the dynamic clock right?
Resune#9806: 1506mhz so far
∫ntegral#0450: i think nvidia core frequencies are multiples of 6.5... |
Resune#9806: Lmao my gpu fans at 85% sounds like a jet
Resune#9806: 52c load temp lmao
Resune#9806: 1527mhz stable so far
Resune#9806: I wonder how far this thing's gonna let me push it on stock before it crashes/artifacts
Deleted User#0000: which is best to use unigin valley or msi kombuster?
pkkshadow#5844: valley/he... |
∫ntegral#0450: but i don't think the 970 is bandwidth limited
∫ntegral#0450: amd gpus are tho
Resune#9806: I'm at 7.2ghz stock is 7ghz
Resune#9806: 1527mhz on core right now, gonna test more in a bit
Resune#9806: 7.2 is stock on this gpu though
Deleted User#0000: im stumped, kombuster cant even get to the boost clock
∫... |
AngryBeardedGaming#9949: i stay at 1500MhZ on my msi 970 golden edition with 1.27v
Resune#9806: I’m 1557mhz at 1.206v
AngryBeardedGaming#9949: whats your ram at?
∫ntegral#0450: what are you testing with?
Resune#9806: Whoa just had a huge stutter
Resune#9806: I’m testing on valley
AngryBeardedGaming#9949: 1500 is the no... |
Resune#9806: 110 I think i saw one
Resune#9806: after 15 mins
AngryBeardedGaming#9949: i have this one https://us.msi.com/Graphics-card/GTX-970-GAMING-4G-Golden-Edition.html
Resune#9806: this is with 0 on voltage
Resune#9806: I was at 1557mhz 1.206v 54C
Resune#9806: 7200mhz on the memory
AngryBeardedGaming#9949: you co... |
AngryBeardedGaming#9949: yeah
Resune#9806: isn't liquid nitrogen just nitrogen2?
AngryBeardedGaming#9949: idk i just huff it
Resune#9806: lmao
AngryBeardedGaming#9949: what cpu do you have?
Resune#9806: i5 6600k
Resune#9806: 4.4ghz
AngryBeardedGaming#9949: nice nice ive got a ryzen 3 1300x at 4.02
AngryBeardedGaming#... |
AngryBeardedGaming#9949: max
AngryBeardedGaming#9949: anything higher you get degradation
Resune#9806: 1.3v max safe volt? so if I'm at the edge with 1552mhz at 1.206v
Resune#9806: I might be able to get some pretty good numbers
AngryBeardedGaming#9949: if it crashes the drivers it will go into a ultra low poer mode
An... |
Resune#9806: well, maybe now that I've got an offset it won't idle that low
Deleted User#0000: what the usual bump for rx 470's?
Resune#9806: right now it's 988mhz on clock, 1800 on memory (3600)
AngryBeardedGaming#9949: https://cdn.discordapp.com/attachments/305981966292090881/551374636114509837/unknown.png
AngryBear... |
Resune#9806: I'm at 1.31v on my 6600k
AngryBeardedGaming#9949: my 1300x is on a dynamic volatge with an extreme load line calibration lock and gets up to 1.45 v sometime
Resune#9806: i've technically got more headroom, but when i small ffts w avx it hits 87C, i can't really confirm higher OC's with my cooling rn
AngryB... |
buildzoid#6254: anyone know the dimensions of a GTX 460 die?
Callista#3917: don't have my GF114 die to measure unfortunately
guardian_six#5058: I have a GTX 465 i could measure, pretty sure I already delidded it
guardian_six#5058: nvm, dies are different
Battlefield_Ace#9175: @buildzoid doesnt gpu-z say what the die si... |
Fitz#8200: is there a point to delidding a gpu?
Mickulty#1560: lower temperatures if you can mount a good cooler and mount it well
guardian_six#5058: I can speak from experience, yes, especially on an OCed Fermi oven
Mickulty#1560: Personally I'm quite against it because it's difficult and risky
Mickulty#1560: But it d... |
Deleted User#0000: msi air boost, i plan to water cool it next month so there's that
DaGunzi#1241: and it broke :AlzaFace:
DaGunzi#1241: ayy mine was an msi air boost too
DaGunzi#1241: maybe let it chill for 2-3 weeks on the stock cooler id say now
Deleted User#0000: yeah, it does fine
Deleted User#0000: fallout doesnt... |
DaGunzi#1241: its better to tune the performance states seperately so you can set kind of a voltage slope too
DaGunzi#1241: newer afterburner version has these 3 lines next to the core clock row which lets you access all the states
Deleted User#0000: right, i see
Deleted User#0000: thank you
Deleted User#0000: i shall ... |
DaGunzi#1241: well its a bit complicated with vega
Deleted User#0000: hawaii it was just slap it and off you go
DaGunzi#1241: which is why i recommended checking what clock speed you are actually getting with hwinfo
DaGunzi#1241: yeah vega has more complex boost thingies
Deleted User#0000: right, i'll boot up hwinfo64,... |
Deleted User#0000: i have a soc clock
Deleted User#0000: its at 600 right now
DaGunzi#1241: really liked that thing, hurt a bit turning down all the settings again today 😄
DaGunzi#1241: yeah thats the one
Deleted User#0000: which power am i going off of? chip? core?
DaGunzi#1241: core bounced around wildly iirc, chip ... |
Deleted User#0000: i do have heaven and valley
Deleted User#0000: will those do?
DaGunzi#1241: yeah sure
DaGunzi#1241: if you fly around in valley and look at the trees from far above it should be a nice and high current draw scenario
DaGunzi#1241: also used that one
DaGunzi#1241: then turn around to the sky for low cu... |
Deleted User#0000: and oh nice
DaGunzi#1241: also good to pause at any scene to test some different loads (space hotkey)
DaGunzi#1241: never tried heaven tbh, only valley and superpos
Deleted User#0000: is 1080ti on 2101 good?
Deleted User#0000: 1.15v
Deleted User#0000: 5800 mem tho
hitek#9195: that's a good core clock... |
Resune#9806: if anyone could help I'd be grateful
Callista#3917: anyone here have experience running MXM GPUs in desktops?
Callista#3917: I'd really like to have a try at OCing my 670m
DaddySpaghetti#1199: @Deleted User which bios?
Mickulty#1560: afaik the adapters for MXM are really fucking expensive
Deleted User#0000... |
Deleted User#0000: nah man
DaddySpaghetti#1199: what's the max voltage on the 970?
Callista#3917: it's a GF114 chip
Deleted User#0000: fully stable
Deleted User#0000: wait
Deleted User#0000: yes
Callista#3917: the problem I had OCing it in my laptop was just power/vdroop limited
Deleted User#0000: when i push mem more ... |
Deleted User#0000: a lot
Deleted User#0000: at least for my chip
Deleted User#0000: 1.093 highest i got was like 2030 or 2040
DaddySpaghetti#1199: oh sweet
DaddySpaghetti#1199: i'm tempted to try the XOC
DaddySpaghetti#1199: what was your gpu score in time spy?
Callista#3917: https://cdn.discordapp.com/attachments/305... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.