data stringlengths 14 24.3k |
|---|
Fael#2479: yea no artifacts or freezing
phoenix#2490: nice
phoenix#2490: thats good
Fael#2479: So what do I do with this curve exactly?
phoenix#2490: find the voltage you stabilise at and increase the clocks on that point
Cancerogeno#1786: Yeah do a couple of bench runs and then look on the voltage graph where the volt... |
Fael#2479: Appreciate al the help btw
phoenix#2490: nah
phoenix#2490: i was trying to get the #1 place for time spy in australia with my specs
phoenix#2490: only got 4th
phoenix#2490: i have the best cpu score tho
Fael#2479: Ok, so say the voltage sits at 1.03
Fael#2479: How do I adjust the graph
phoenix#2490: you find... |
Cancerogeno#1786: I'd suggest you to lock that point when you're done
Cancerogeno#1786: Press L to lock
phoenix#2490: oh my god
phoenix#2490: i was having issues when overclocking with it jumping up and down
phoenix#2490: but YOU CAN LOCK
Cancerogeno#1786: Yeah man it helps a lot during bench runs
phoenix#2490: omg
pho... |
phoenix#2490: incase your temps are better or worse
Cancerogeno#1786: No just drag the stable point and press apply
Cancerogeno#1786: The curve will auto adjust
phoenix#2490: ah
Cancerogeno#1786: Just make sure there are no other points on the same horizontal line before the stable voltage point
Fael#2479: So the part ... |
Cancerogeno#1786: Yeah it quite high 😄
richiec77#9494: Lol.
Fael#2479: Wait is that good
richiec77#9494: If your card can run that....it's a Top bin
Cancerogeno#1786: Yeah considering you're on air it's high
richiec77#9494: 2110 is a better starting point
Fael#2479: Lol yeah didn’t run
richiec77#9494: And at 1.050v
Fa... |
Cancerogeno#1786: Also those cards are pretty castrated by the bios power limit
richiec77#9494: Air...55-65C, it's 3 Boost bins down from typical max boost bin at 35-39C
Fael#2479: Cool it running
richiec77#9494: 2130 might be possible. Just depends on how good the chip is, the Voltage needed and Temps. Temps being kin... |
Fael#2479: Ight sick
Fael#2479: I think I’m just about down with this gpu lol
phoenix#2490: https://i.imgur.com/KCvhfQR.png for a 1060 6gb on air
Fael#2479: I’ll finish my ram another night
richiec77#9494: Would want a full play time session to see how stable
Fael#2479: Right
phoenix#2490: i just use a time spy run
pho... |
richiec77#9494: As the card heats up, it goes down 1-3 steps on the V/F curve
Cancerogeno#1786: Yeah no way you can sustain 1.093 on standard 1060 bioses
richiec77#9494: You should smooth out the steps down to 1.013v
phoenix#2490: i don't understand
richiec77#9494: Aka 1.063v/2113
phoenix#2490: can you draw it on ms p... |
richiec77#9494: It'll start hunting downwards as it gets warmer
phoenix#2490: yeah so ima test on 1 monitor and then on my 2nd ill have afterburner open
richiec77#9494: It chooses based on the Voltage
richiec77#9494: The voltage on the graph determines your frequency
phoenix#2490: and i want to watch the voltage
Fael#2... |
Cancerogeno#1786: Yeah
Cancerogeno#1786: But it think it might be around 1.030 for you too
phoenix#2490: i'll see
richiec77#9494: The lowest voltage you can run produces the least amount of heat and allows for the most within power limits
phoenix#2490: weird
phoenix#2490: after 2 gpu tests it was 60C and 1.093v
Cancero... |
phoenix#2490: i'll redo it with my oc applied
Cancerogeno#1786: You need to look for the flat spot not the spikes
phoenix#2490: https://cdn.discordapp.com/attachments/305981966292090881/650642000453959680/unknown.png
Cancerogeno#1786: Yeah it's good
Cancerogeno#1786: But I really doubt the voltage will be stable
phoen... |
phoenix#2490: good?
Cancerogeno#1786: The last pne
Cancerogeno#1786: Check the box and disable it
phoenix#2490: ahh
phoenix#2490: got it
Cancerogeno#1786: The card will not downclock anymore due to temp
phoenix#2490: how is this tool not known wtf
Cancerogeno#1786: Afaik it's an old Nvidia internal tool
phoenix#2490: i... |
phoenix#2490: ill try again
phoenix#2490: 1043v
phoenix#2490: really low
Cancerogeno#1786: Tbh that's the voltage I would expect from that card
Cancerogeno#1786: But yeah it's weird
phoenix#2490: why is it so low wtf
phoenix#2490: even after turning the program off
Cancerogeno#1786: Because that's the right voltage
pho... |
phoenix#2490: i just removed the registry edits thru the program
phoenix#2490: ima try again
phoenix#2490: if not, driver reinstall
phoenix#2490: yeah, i just loaded an old profile and i was getting a solid 1081 and 2113mhz
Aqwrd#7164: How can I overclock memory on r9 fury? I think it’s locked
zhrooms#0659: 2080 Ti, th... |
zhrooms#0659: one less SMD
Resune#9806: depends on the importance of the capacitor, but a lot of capacitors are for like what betrayed said, redundancy and for better efficiency etc
Resune#9806: it's common to be able to lose a cap on a cpu and for nothing to be different
Betrayed#3582: People knock off SMD caps off of... |
Betrayed#3582: It would have to be soldered back on
Betrayed#3582: As long as the pads are intacted you could do if it you have the tools
zhrooms#0659: solved
zhrooms#0659: some dude on OCN in 2018, had the EXACT same SMD fall off <https://www.overclock.net/forum/69-nvidia/1714386-damaged-2080-ti-pcb.html>
zhrooms#0659... |
Cancerogeno#1786: Hey guys, I'm having a kinda odd issue with a system on 2 psus, when shutting it off the motherboard actually keeps powered on for some reason
Cancerogeno#1786: like post code shows 00 and fans plugged in still spin, it shuts down only if I manually switch off the second psu that powers the gpu
Cancer... |
Resune#9806: artifacting/crashing
Fael#2479: Thanks.
Tyllo#2609: so I flashed my msi 2080ti trio with the 406w bios that's been out for a while.. gpu-z correctly reads the new version and afterburner lets me set the power limit to the correct value (135% instead of 110% with default bios) but for some reason the card i... |
Fitz#8200: driver tweaks
phoenix#2490: my gpu does 2126mhz on the core (#1 spot is 2088) and the memory around 4519
phoenix#2490: how exactly would i do that?
Fitz#8200: adjust LOD
phoenix#2490: oh yeah\
Fitz#8200: although idk if nvidia 3dmark can catch nvidia stuff
phoenix#2490: https://steamcommunity.com/app/223850/... |
phoenix#2490: oh do they not work properly in safe mode
Fitz#8200: safe mode is supposed to disable drivers and everything not sys/os related
phoenix#2490: ohh
phoenix#2490: okay
phoenix#2490: i'm going to ddu and get the latest drivers
Fael#2479: what is ddu?
Fitz#8200: display driver uninstaller
Fitz#8200: lets you c... |
PablO#1842: Cause I’m not sure when I achieved the right oc
PablO#1842: And idk what good stress tests to run etc
keeph8n#0369: Port Royale
Resune#9806: 3DMark is the best for paid stress/benchmark tests and superposition is about the best for free
PablO#1842: Thx
PablO#1842: And about the actual oc. Is there anything ... |
PablO#1842: Ok I’ll install it
PablO#1842: Also i seem to be having temp issues on my card even though I have good pc airflow
PablO#1842: While running kombuster it hit its max temps at 88
PablO#1842: :|
PablO#1842: This is at 100 load
keeph8n#0369: Doesn’t seem out of line
Fael#2479: Seems fine it’s stress testing
Pab... |
PablO#1842: I should have gotten a 5700 xt. I don’t really need a 2080s. Fans at 60. I tested 100 and it still hit 88
PablO#1842: AMD cards overclock better?
Resune#9806: a 2080 super overclocked will smoke a 5700XT overclocked
PablO#1842: Well I know but they are at different price ranges
PablO#1842: I’m still having ... |
Resune#9806: some AIB's overclock the memory a bit
PablO#1842: And like 120 on core or something
PablO#1842: Aibs 🧐?
PablO#1842: Offset
PablO#1842: I don’t understand these big words
Resune#9806: AIB stands for add in board, so like MSI, EVGA, Asus, gigabyte etc
Resune#9806: nvidia's founder cards would be a case of n... |
Resune#9806: but maxwell didn't require a signed vbios so you could really customize how your card behaved and modify power limits
PablO#1842: How do you check if a gpu uses Turing or pascal etc
Resune#9806: pascal is when that was taken away, it required vbios signatures, which you can't sign your own bios edits
Resun... |
PablO#1842: I have FPS capping problems
PablO#1842: My gpu looks to a certain usage
Resune#9806: that can be an issue with the game engine/bottlenecking
PablO#1842: Like this one guy has a 1080 ti and he got 100 FPS on overwatch and turns out his gpu was 10% usage
Fael#2479: Haven't had issues with nvidia drivers
PablO... |
PablO#1842: No thermal issues either. I have a d15 for my 3700x
Fael#2479: That's just not true
PablO#1842: What is?
PablO#1842: Overwatxh mainly uses gpu resources...
Resune#9806: overwatch can run just fine on a 4c4t and jedec ram, it's mostly gpu that'll get you above 144fps
PablO#1842: See fael
PablO#1842: Idk what... |
Resune#9806: 4c4t means 4 cores 4 threads, jedec is a specification for ram, it's what your ram runs at when not overclocked (xmp is overclocking)
PablO#1842: I actually understand some of this
PablO#1842: I just don’t get the abbreviations you use sometimes
Resune#9806: anyway lets get this back to GPU OC questions, w... |
PablO#1842: Ok
Resune#9806: make sure to read over the #read-the-rules, useful information in there
PablO#1842: ?
Resune#9806: it'll help you not break the rules in here and know how to use the server
PablO#1842: Wha
PablO#1842: Ok
reaz#0283: Can any1 help overclocking my rx 5700 xt?
Fitz#8200: step 1: Download morepow... |
reaz#0283: ye i got it
reaz#0283: https://cdn.discordapp.com/attachments/305981966292090881/651848653044187170/unknown.png
reaz#0283: do u mean this max power limit
reaz#0283: i cant put it to 100
Fitz#8200: 99% power and see how much the core/mem goes
Fitz#8200: if you max a slider, increase it in powertool
reaz#0283... |
Fitz#8200: https://cdn.discordapp.com/attachments/305981966292090881/651849566899142696/unknown.png
reaz#0283: https://cdn.discordapp.com/attachments/305981966292090881/651849858956787772/unknown.png
reaz#0283: i only have this
reaz#0283: https://cdn.discordapp.com/attachments/305981966292090881/651850481479712778/u... |
Resune#9806: i guess it depends on what you're looking for, temp soaking or stability, because 3DMark with both my 970 and 1070 is a lot harder to be stable in than superposition
Shai#1169: I’ll try out 3DMark then
phoenix#2490: 3dmark is my go-to, it stresses more
phoenix#2490: yeah
Dragos"Tbrick"#8463: https://cdn.d... |
keeph8n#0369: Yes they are
keeph8n#0369: My three way had the air card in slot one, as it had the best memory OC capability https://cdn.discordapp.com/attachments/305981966292090881/652353067857215506/image0.jpg
MRschmeckles#6319: fuck ive been looking for a white shroud gpu for a while, kinda tempted to order a galax
... |
Deleted User#0000: I use superposition actually
Zeny1 😎#1950: weird situation my RTX 2070 is ignoring fan curves. Software wise it says it's following the fan curve but monitoring it with GPUZ you can see the fan RPM's ram up but the fan speed % is the same as what I have set up. Any tips?
Zeny1 😎#1950: using MSI aft... |
Zeny1 😎#1950: I fixed it.
Zeny1 😎#1950: I posted on a different discord
Zeny1 😎#1950: so my fuckin 2070 was defective
thats why it was super loud
I went on forums cuz it was unbearable
I decided to void warranty and open it up
there were specks of what seems medal on some of thermal pads and on the paste
I removed a... |
3DMark.com
I scored 7 973 in Time Spy
Intel Core i7-8700K Processor, NVIDIA GeForce RTX 2070 x 1, 16384 MB, 64-bit Windows 10}
7973 > 9251
big jump im happy even with voided warranty
MSI is a shit company don't buy their shit
Tyllo#2609: I don't think you need to worry about the warranty as long they can't say you bro... |
Tyllo#2609: even if the label isn't specifically illegal
Zeny1 😎#1950: You wouldn't believe the stuff we have here
Tyllo#2609: they won't hold you to that, 90% sure
Tyllo#2609: you could totally send them an email as well, include both your results, and ask if they think you did a mistake lol
Zeny1 😎#1950: well its o... |
Zeny1 😎#1950: but this was a failure on their part
Zeny1 😎#1950: very shameful to have specks of what seemed metals in their pads and paste
Tyllo#2609: got my own issues with a power limit I can't bypass even with the stupid high power limit bioses
Tyllo#2609: seems to just be hardware locked
Zeny1 😎#1950: oh yeah
Z... |
Zeny1 😎#1950: It's board partner not doing good boards
Zeny1 😎#1950: if you want to go crazy I heard the 2080 ti kingpin is best
Zeny1 😎#1950: It's a monster
Tyllo#2609: yeah, gonna wait for ampere and see what the prices are like
Tyllo#2609: might try to sell my card
Zeny1 😎#1950: oh for sure someone would buy atm... |
keeph8n#0369: @Alcyone
Alcyone#2233: its offset and has considerable droop. i'll run a quick test and see what the max is
keeph8n#0369: I assume AB only letting you do +100mV
Alcyone#2233: yes and trixx is not working for some reason, tried a few different versions
keeph8n#0369: I haven’t gotten past 1235 on ref boards... |
Alcyone#2233: gaming mine can do like 1650 vram, I can run 1800 in TS with no artifacting or freezes
Alcyone#2233: core doesnt seem to be so great though
keeph8n#0369: My VaporX card does 1200/1500 but takes +150
Alcyone#2233: mine is a VaporX as well but the reg 290 non X
keeph8n#0369: Mine are all regular 290s
Alcyon... |
Alcyone#2233: touch of modern is the name of the skin
Ssateneth#7162: https://www.ebay.com/itm/114004558871
Ssateneth#7162: nvidia HBM video card engineering sample
Ssateneth#7162: wut is this
Ssateneth#7162: photos suck, low res
MRschmeckles#6319: is there a known list of temps when 1080s start to down clock? when st... |
phoenix#2490: i downloaded that as well, it made it worse
Cancerogeno#1786: On Pascal and earlier it should stop thermal downclocking
Cancerogeno#1786: Of course you'll still face the power limit
Cancerogeno#1786: On turing cards it breaks the driver and makes them bsod so do not try the third box in the program, the f... |
Cody Seay#8706: Getting rid of the stock paste on my 5700xt 24hrs after it shows up :ok_hand: :grin:
Aqwrd#7164: Why would unigine tell me my mem clock is 650 but afterburner says it’s 500. Fresh install of windows, also it’s an r9 fury which is mem locked. My score shot up 250 points
Aqwrd#7164: @Cody Seay#8706 very ... |
Deleted User#0000: But I almost got 10k in Timespy with the card on air lol
Cody Seay#8706: Didnt try washers
Deleted User#0000: If you do make sure they’re thin. Like the washers that come with a Corsair liquid cooler. I had some floating around from my H150 that I used
Cody Seay#8706: Good to know I should have some ... |
Speedfap#2162: yeah
phoenix#2490: what do you play?
Speedfap#2162: so i run a 1070FTw
Speedfap#2162: wow
Speedfap#2162: would this be a huge upgrade in terms of fps output
phoenix#2490: keep the 1070 if you don't play like really intensive gaqmes
Speedfap#2162: https://www.pbtech.co.nz/product/VGAGBV22070A/Gigabyte-GeF... |
Speedfap#2162: i have x2 display port cables - 1 to each of my monitors
Speedfap#2162: does it matter which one i use? is one like primary and one secondary or it doesnt matter?
phoenix#2490: i think there will probably be like displayport 1.2a, 1.2, whatever, but it really wouldn't m,atter
Speedfap#2162: mmm
Speedfap#... |
Fitz#8200: Ref amd navi cards report 65k rpm if you dont have the fan connected
MRschmeckles#6319: @siegmour that's the only pic. It's a friends 1070 or 1070 ti red dragon card. I have absolutely no idea how it squishes out the side and doesnt cover the chip. All I can think of is the cooler was tightened too much and ... |
Aqwrd#7164: Do I just put a jumbo pea sized squirt of thermal paste? https://cdn.discordapp.com/attachments/305981966292090881/653688062169317396/image0.jpg
Resune#9806: you'll want to remove the old paste, and spread on new paste
Resune#9806: pea method isn't a safe bet on gpu's, they don't have the same kind of mount... |
phoenix#2490: wtf is that
Deleted User#0000: are there any good undervolting guides for a 1080ti
siegmour#8482: @Deleted User Overvolting on GPUs is generally the same (although they all might have some quirks) -> reduce voltage until it starts crashing. You can also lower clocks in order to achieve even lower voltages... |
Deleted User#0000: my gpu ran really hot at 89c so I knew it was time to repaste
Deleted User#0000: after that it dropped about 3-4c
Deleted User#0000: so yeah, 85-87c
Deleted User#0000: I don't know about those lanes
Deleted User#0000: what do you mean by single vs two seperate cables
Deleted User#0000: it's 6+8pin
De... |
siegmour#8482: That's pretty standard about the side panel.. in fact 1C is quite low of a difference
Deleted User#0000: i have a carbide clear 600c inverse case
Deleted User#0000: it's fairly big case
siegmour#8482: And I have a Define R6 which is a full-sized tower case with 5 intake + 2 exhaust fans, but I still drop... |
xlen#6206: anything below 100C
xlen#6206: Tjmax is 110C iirc
xlen#6206: VRAM obv much cooler
Spy#6108: Should I mess with the fans if at stock it only hits 89C hotspot?
xlen#6206: as you wish, the cooler it runs, the higher it boosts
xlen#6206: the faster the fans spin the louder it will be
Spy#6108: HMM
Spy#6108: Is i... |
xlen#6206: It's fine
xlen#6206: those 65Mhz won't give you more FPS
Spy#6108: True
Spy#6108: My main concern wasnt throttling with the temp, just curious what I should aim for as far as longevity
Fitz#8200: The 2025 is the set freq, depending on how far you are from the power limit, you'll boost closer to it
Spy#6108: ... |
Fitz#8200: What are you actually getting freq wise?
Spy#6108: when gaming its sitting at 1965 max
Spy#6108: havent seen it go above
Spy#6108: monitioring with hwinfo
Fitz#8200: It doesn't sit at 1965
Spy#6108: Maybe I misunderstand then
Spy#6108: What do you mean
Spy#6108: @Fitz I appologize for not being super experie... |
Fitz#8200: It boosts what it needs to boost too
Spy#6108: Would you advise bringing the volts down a tad?
Fitz#8200: What are temps?
Fitz#8200: And power draw?
Spy#6108: Hotspot sits around 90C with games that fully utilize the card
Spy#6108: Power draw is around 230
Fitz#8200: You're fine then
Spy#6108: So it’s better... |
Spy#6108: Well I know artificial pushes it a bit further
Fitz#8200: not necessarily, just need an intensive game
siegmour#8482: Yeah, like Overwatch or Doom 👀 Power draw very similar/identical to Kombustor depending on settings
Resune#9806: I feel that may depend greatly on setup
Resune#9806: nothing comes close to fu... |
Then the VRM gets hot and efficiency goes down
Fitz#8200: for nvidia's boost logarithm ^
Betrayed#3582: Over FurMark good thermal stress test
Betrayed#3582: Nothing more
Fitz#8200: thermal stress and seeing what a power limit is set at
onyx#2017: is it ok to have my gpu fans on 100%?
onyx#2017: https://cdn.discordapp... |
onyx#2017: 😂
onyx#2017: ok
onyx#2017: i have a i3 4400k, 12GB DDR3 and RX580 8GB OC
onyx#2017: i should really buy a cpu
onyx#2017: but i have a very outdated mnotherboard socket so i might have to go with a ii7 4th gen
paladzin#1314: i3 4400k? :thinkies:
Fitz#8200: getting a 4th gen i7 will cost as much as a new low ... |
Resune#9806: it'll cost more, but zen 2 is worth it over a 2600
paladzin#1314: be a perfect choise
Resune#9806: but if budget won't allow, a 2600 will be the better choice
Fitz#8200: I waa going off newwgg prices, and a 2600 was $120
Fitz#8200: We need some dual socket am4 at that price
Deleted User#0000: Anyone know g... |
Resune#9806: superposition for a free benchmark
Resune#9806: paid would be 3DMark
Deleted User#0000: You can OC your ram in BIOS right?
Resune#9806: by ram you mean dram and not vram right?
Deleted User#0000: What the diff between dram and vram?
Resune#9806: dram is for your system, vram is for your gpu
Betrayed#3582: ... |
Shai#1169: so I updated my radeon settings and this new interface sucks
Shai#1169: wattman is gone and so my unlocked limits are back to default
Shai#1169: and morepowertool doesn't work anymore
Shai#1169: anyway to revert back to the previous version?
Alcyone#2233: use DDU then reinstall the earlier driver
Shai#1169: ... |
QuePaso#5074: So far , I'm +225Mhz on core and +650 on Memory
QuePaso#5074: Is that any good ?
Resune#9806: offset doesn't mean much i need to know the effective
Resune#9806: what does it say in hwinfo or afterburner
QuePaso#5074: I've hit 2100mhz (at some point) and 2,328Mhz on memory
QuePaso#5074: Readings from Hwinf... |
Resune#9806: I can give you my benchmarks to compare to if you'd like but it's not apples to apples
QuePaso#5074: best one yet https://cdn.discordapp.com/attachments/305981966292090881/654830246020907011/ultimate_oc.PNG
Resune#9806: I've never done a FSE test
Resune#9806: timespy extreme is the heaviest 3DMark test for... |
Resune#9806: but it never gets that hot
Resune#9806: https://cdn.discordapp.com/attachments/305981966292090881/654835553539457028/unknown.png
Science#2264: Can somebody help me for a little bit? I'm trying to safely OC my 1060
And I don't want to mess it up
Is MSI afterburner worth while?
I know almost NOTHING about O... |
Science#2264: Should I up the memory?
Resune#9806: do core clock first then memory
Resune#9806: go in steps of 50mhz in a benchmark like superposition or a 3DMark one
Resune#9806: then once it starts crashing go down 25mhz until stable
Resune#9806: then do the same for memory
Resune#9806: but if you're running into thi... |
MRschmeckles#6319: Any idea what is going on here? Looks like corrosion? Card works https://cdn.discordapp.com/attachments/305981966292090881/654851610454786064/20191212_190145.jpg
Extreme_Blaxkor#7367: does pascal really scale in performance past 2100mhz
Extreme_Blaxkor#7367: i have tried to run a 1080 at 2350 with th... |
Deleted User#0000: now I'm seeing 7720 wowzer
Extreme_Blaxkor#7367: i need to see if my gpu is having negative performance scaling with frequency
Extreme_Blaxkor#7367: i remember benchmarks being much higher with 2250mhz over 2350mhz
Extreme_Blaxkor#7367: not sure why adding 100mhz causes a massive drop in performance
... |
The Peasantry Hut#1337: Managed 1550MHz with a .050v bump.
xlen#6206: Anybody already tried to OC the 5500XT?
Ssateneth#7162: @MRschmeckles i see green crud. looks like water got on it.
Ssateneth#7162: SN starts with a 15 so it's out of warranty
Ssateneth#7162: usually if a video card is really dirty, i'll disassemble ... |
Ssateneth#7162: i mean i've seen some pretty gross... "solutions" for failed GPU fans so people zip tie whatever they can find to the GPU
MRschmeckles#6319: @Ssateneth no I need a half height gpu. Its literally too tall
Ssateneth#7162: yeah thats what i said. low profile
Ssateneth#7162: thats the same thing right?
Ssat... |
Ssateneth#7162: though TBF the mounting screws only screw in so far
The Peasantry Hut#1337: I've got a hardware store near me that I used to work at, so I'm super familiar with sizes and types and such. I'll get it figured out. It'll be one hell of a fun project, though
The Peasantry Hut#1337: After I send this 4790k o... |
Resune#9806: yes there is error correction, and you may still be stable, but you may be losing performance due to the performance cost of the ECC
Resune#9806: use a benchmark to see if increasing memory clock is increasing performance or causing regression
Spube#7475: Ok I've officially gone mad with power. Let's see h... |
phoenix#2490: what's so black magic about ram?
Sayeru#0001: im getting around an 80 mhz oc on my core clock but when i use the msi afterburner auto oc the average ranges from 15 to 19 am i doing something wrong? i was under the impression the auto oc isnt too far behind a manual oc
Sayeru#0001: 2080s
phoenix#2490: @The... |
phoenix#2490: there are 5000 kits available, all you need is money, a good cpu, and a good motherboard
The Peasantry Hut#1337: Yeah, but there's still a ton of stuff you account for compared to CPUs and especially GPU overclocking. And it's not a solid gain on my end, so I don't bother with it
phoenix#2490: cpu overclo... |
The Peasantry Hut#1337: And the gains are negligible for everyday use
phoenix#2490: but he doesn't understand why
phoenix#2490: yeah fair enough
The Peasantry Hut#1337: I get why you want to, but if it doesn't help by Cinebench score in a meaningful way, I'm not going to bother.
phoenix#2490: yeah
phoenix#2490: i like ... |
phoenix#2490: nice
phoenix#2490: i wish i had a gpu sitting around
phoenix#2490: this is getting out of topic, ima type in #general
The Peasantry Hut#1337: I might just sit tight at 5.0GHz and start with the GPU and see what happens. Never really tried to push it balls to the wall
The Peasantry Hut#1337: Yeah, let's go... |
Spube#7475: U WHAT
Deleted User#0000: but that can't be right
Deleted User#0000: has to be bullshit
Deleted User#0000: no fucking way
Spube#7475: That or you're just too fucking powerful
Deleted User#0000: :bhinking:
The Peasantry Hut#1337: :trouffGlee:
Spube#7475: You are now jesus.
The Peasantry Hut#1337: https://ten... |
Spube#7475: Nah I'll just use a jigsaw
Spube#7475: With a hacksaw blade
The Peasantry Hut#1337: Man, I love having this GPU under water. pulling 1573MHz (+270MHz offset) and it barely breaks 40C
The Peasantry Hut#1337: The reference cooler would be screaming at +100MHz lmao
Spube#7475: I gotta say I prefer thicc air co... |
The Peasantry Hut#1337: I had the Corsair SP120L's. I need custom earplugs lol
Deleted User#0000: obama, if you are really after them big juicy clocks you should try going colder
The Peasantry Hut#1337: I have the Etymotic earplugs. Works wonders, but I need custom molded ones since I'm a sound engineer for a venue.
Th... |
Deleted User#0000: what card?
The Peasantry Hut#1337: I have no clue. Never worked with Vega
Spube#7475: My card is a nitro+ but isn't the limited version
The Peasantry Hut#1337: 660, 970, 980, and 5700xt for me
Deleted User#0000: is that the junction?
Spube#7475: I guess???
Spube#7475: How would I know the difference
... |
Spube#7475: Wait no
Spube#7475: It was 35
Spube#7475: I'm going insane
Deleted User#0000: 35v or .35
Spube#7475: Mv
Spube#7475: Sorry
Spube#7475: That said I changed the fan curve for that profile to scream at full blast after that run
Spube#7475: Don't know how it will be now
Spube#7475: Also I'm using thermal grizzly... |
The Peasantry Hut#1337: My Red Devil has zero sag lol
Spube#7475: Hot spot is big chilling in the 80s degree C
Spube#7475: I honestly don't know how much sag my GPU would have without the bar.
The Peasantry Hut#1337: 80C seems alright for junction temp. For Navi, it's fine. Especially for aftermarket coolers.
Spube#747... |
Deleted User#0000: what have you heard
The Peasantry Hut#1337: I wonder what they'll go with for numbers this time
The Peasantry Hut#1337: because a 6900XT sounds hilarious to market
Spube#7475: That it's being revealed around I think computex or ces. One of those kind of in the spring
The Peasantry Hut#1337: Oh, and h... |
The Peasantry Hut#1337: kinda both, Both are very good.
The Peasantry Hut#1337: I just run Valley or Heaven because it loops, then transfer over to 3DM because I'm too cheap to buy it and don't want to sit through demo after demo..
Spube#7475: Damn why haven't I installed heaven or valley yet
The Peasantry Hut#1337: Th... |
Spube#7475: The monitor on the left was free
The Peasantry Hut#1337: For OC, yeah. I don't understand the uses for everyday stuff, though. I'd much prefer landscape
Spube#7475: 60hz, 1080p, 'windows vista compatible'
Spube#7475: I have a main monitor in landscape, but vertical can come in handy for discord, browsing, a... |
Spube#7475: https://cdn.discordapp.com/attachments/305981966292090881/655398521347768361/20191214_081928.jpg
Spube#7475: Huh.
Deleted User#0000: vega lmao
Spube#7475: Intriguisting
Spube#7475: So is this normal?
Spube#7475: Also what's the deal with the timing levels in radeon settings? All I can find online is that t... |
Spube#7475: Finally figured out timing levels
Deleted User#0000: should I max power limit AND core voltage for my 2080
Deleted User#0000: and leave core clock and mem clock alone?
Sprocket#6315: Anyone got a 2080? What is a good overclock for it?
CRINSIE#8168: Im using msi afterburner to oc my 1070ti but when i like pr... |
CRINSIE#8168: well even when i do +10 it switches back
Deleted User#0000: oh
Deleted User#0000: no clue
Deleted User#0000: sorry
Spube#7475: So I got an r9 fury nitro for dirt cheap. Have no idea what I'm in for. Any tips on squeezing extra speed out of these things?
phoenix#2490: if i recall correctly wattman is the b... |
Spube#7475: I gave up like 45 minutes in, ordered some arcticlean, then took a nap
Spube#7475: Shit was like concrete
Spube#7475: Also there's a lot of discoloration on contact point of the air cooler (forget the actual term). Is that an issue?
Spube#7475: It looks almost like oxidation but I've never seen it this bad ... |
∫ntegral#0450: but that hasn't helped at all with memory oc, at least for me
∫ntegral#0450: do 2150-2200 and tighten the timings
Dimi#3164: Hello everyone I have an asus vega 64 and I don't understand the new amd interface and I would like to underclock to gain peformance
Dimi#3164: sorry about my english i'm french
25... |
🎗xensor👿#7176: @∫ntegral how do you do timing with rx 580?
∫ntegral#0450: https://github.com/Eliovp/AMDMemoryTweakXL
∫ntegral#0450: that doesn't work if you idle at memory clock
∫ntegral#0450: in that case, you'll have to mod your bios
🎗xensor👿#7176: @∫ntegral oh. Is it easy to reset of it goes wrong?
🎗xensor👿#71... |
Spube#7475: Taste the rainbow
Spube#7475: Ok
Betrayed#3582: bare copper tarnishes and heat won't help it
Deleted User#0000: @smcelrea i can change core and memory
Spube#7475: But it doesn't affect heat transfer?
Betrayed#3582: no
Betrayed#3582: not in anything meaningful way
smcelrea#3196: click on the settings cog an... |
Deleted User#0000: @smcelrea hello?
Deleted User#0000: it seems greyed out despite the setting change?
🎗xensor👿#7176: @∫ntegral yes
∫ntegral#0450: yeah, you just restart your pc and settings will be reset
smcelrea#3196: if it's still greyed out you cant undervolt it
smcelrea#3196: but you can still overclock it
MRsch... |
teatime#3449: I have a 2080Ti K|NGP|N edition (hybrid/liquid cooled) at 2180MHz, and while using Unigen/Unigine, I crash at 4k but not 1080p...
keeph8n#0369: Then it’s not stable
teatime#3449: @keeph8n Thanks, but any idea as to why it's having a hard time getting to 2200?
keeph8n#0369: No idea
teatime#3449: alright
te... |
MRschmeckles#6319: I had a stable oc until I adjusted V. Makes me think I should crank voltage up first then try to oc
phoenix#2490: yeah, voltage all the way up and run a 3dm test
phoenix#2490: then find the voltage it stabilises at
keeph8n#0369: Please don’t crank voltage needlessly
pimP#0289: whats 3dm? im currently... |
phoenix#2490: but superposition is 2nd best
phoenix#2490: and good free
pimP#0289: thanks
MRschmeckles#6319: I bought 3dm for like $5 a couple weeks ago
keeph8n#0369: Realistically you want to use a bench with the correct engine for your needs
keeph8n#0369: Direct X 9, 10, 11, etc
pimP#0289: i was looking at 3dm last n... |
Fitz#8200: Adrenaline 20 being buggy would be my guess
Deleted User#0000: figured
Deleted User#0000: lets bench it
Deleted User#0000: yeeehaaaw
Deleted User#0000: GET FUCKING DABBED ON
Deleted User#0000: https://www.3dmark.com/3dm/41984994?
Spube#7475: Out of curiosity what kind of cloth do you guys use to clean off di... |
Spube#7475: You might be using nicer ones lmao. Like I said, these are like 5 bucks for a pack of 50
phoenix#2490: oh lol
phoenix#2490: i just found one laying around and it works well
Spube#7475: https://cdn.discordapp.com/attachments/305981966292090881/656241151761973249/20191216_160738.jpg
Spube#7475: Thinking abou... |
Spube#7475: Problem is it gets too sticky sometimes lmao
Spube#7475: Like it gets hard to remove the plastic protector film stuff sometimes
The Peasantry Hut#1337: Oh for sure. The film is kinda tough to peel off because it peels off the tape itself lol
The Peasantry Hut#1337: Got a bit of a question on some older hard... |
The Peasantry Hut#1337: I lifted the card by the cooler a bit (it's on its side) and Temp3 decreased by a lot
The Peasantry Hut#1337: That's the one that changes drastically when moving the cooler around, so I'm thinking that's an edge temp somewhere
The Peasantry Hut#1337: https://cdn.discordapp.com/attachments/3059... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.