MACHINE_NO stringclasses 48 values | ERROR_ID int64 1 999 | ERROR_CODE stringclasses 245 values | ERROR_DESC stringlengths 14 179 | ERROR_CATEGORY1 stringclasses 11 values | SOLUTION stringlengths 40 290 |
|---|---|---|---|---|---|
KM-ASSYM5-06 | 39 | M7038 | M7038-The work area blocking cylinder is rising abnormally (X33), please check whether the cylinder is stuck when rising | Organizational Abnormality | The solution for the error M7038-The work area blocking cylinder is rising abnormally (X33) is to check whether the cylinder is stuck when rising. If it is, the cylinder may need to be |
KM-ASSYM5-06 | 40 | M7039 | M7039-The work area blocking cylinder is abnormally descending (X34), please check whether the cylinder is stuck when descending | Organizational Abnormality | The solution for the M7039 error is to manually lower the cylinder and verify that it moves freely. If the cylinder only moves when lowered, it may be stuck and the maintenance team should be consulted for further investigation and repair |
KM-ASSYM5-06 | 41 | M7040 | M7040-The jacking cylinder in the work area rises abnormally (X31), please check whether the cylinder is stuck when rising | Organizational Abnormality | There are several possible reasons for M7040-The jacking cylinder in the work area rises abnormally. One cause could be a stuck cylinder, which could be due to pressure buildup or debris blocking the cylinder |
KM-ASSYM3-04 | 8 | M7009 | Alarm: pad pushes out cylinder 1_moving position alarm | Organizational Abnormality | The solution for the "pad pushes out cylinder 1_moving position alarm" error would likely involve checking the wiring and making sure that the pad and cylinder are properly aligned. It is recommended to contact a professional mechanic if |
KM-ASSYM3-04 | 33 | M7045 | Alarm: initial startup, there is material in the assembly line | Abnormal personnel operation | To fix the error described as Alarm: initial startup, there is material in the assembly line, you'll need to identify the source of the material and clear it from the assembly line. This may require adjusting your manufacturing processes or stopping production |
KM-ASSYM4-05 | 1 | M7000 | M7000-The glue bucket is about to be used up, please prepare to fill the glue bucket | Abnormal personnel operation | The solution to the M7000 error message "The glue bucket is about to be used up, please prepare to fill the glue bucket" is to refill the empty glue bucket before it runs out of glue. This |
KM-ASSYM4-05 | 7 | M7006 | M7006-1 point detection failed | Visual abnormality | The solution for the M7006-1 error "point detection failed" cannot be provided without additional information about the underlying cause. This error occurs when the device fails to detect a point or location. It could be due to various reasons such |
KM-ASSYM4-05 | 8 | M7007 | M7007-2 point detection failed | Visual abnormality | The solution for the M7007-2 point detection failed error typically involves resetting the camera or device, updating driver software, or contacting technical support for further assistance. |
KM-ASSYM4-05 | 9 | M7008 | M7008-3 point detection failed | Visual abnormality | The M7008-3 point detection failed error is typically caused by issues with the camera or computer hardware, improper software installation or settings, or insufficient light conditions. The solution may include checking for hardware malfunctions, updating software and |
KM-ASSYM4-05 | 10 | M7009 | M7009-4 point detection failed | Visual abnormality | The solution for the error "M7009-4 point detection failed" typically involves checking the camera's settings, performing a calibration, and updating any necessary software. If the issue persists, it may require technical support from the |
KM-ASSYM4-05 | 11 | M7010 | M7010-5 point detection failed | Visual abnormality | The M7010-5 point detection failed error typically occurs when the device's camera is unable to detect points due to poor lighting conditions, camera focus, or hardware problems. To resolve this issue, try cleaning the camera lens, adjust |
KM-ASSYM4-05 | 12 | M7011 | M7011-6 point detection failed | Visual abnormality | The M7011-6 error occurs when the camera is unable to accurately detect points in the field of view. Possible causes of this error include poor lighting conditions, camera shake or movement, incorrect lens settings, or a dirty or damaged |
KM-ASSYM4-05 | 14 | M7013 | M7013-8 point detection failed | Visual abnormality | M7013-8 point detection failed error can occur in AutoCAD when the program is unable to detect points accurately. One potential solution is to increase the accuracy of the point detection settings or to use a different type of point detection algorithm |
KM-ASSYM4-05 | 15 | M7014 | M7014-9 point detection failed | Visual abnormality | The solution for error M7014-9 is to check the image quality, ensure the object is visible, and review the settings in the object detection algorithm. If necessary, you may need to adjust the object detection parameters, increase the object |
KM-ASSYM4-05 | 18 | M7017 | M7017-The device model setting has not been set, please set the device model | Abnormal personnel operation | To fix the M7017 error, you need to set the device model on your Amazon App Store account. This can be done by following the steps in the Amazon Developer Console: |
KM-ASSYM4-05 | 21 | M7020 | There is no code scanner in the work area of ??M7020-T surface, so self-inspection cannot be e done in the work area. Please put the undispensed plate in the front buffer to start | Abnormal personnel operation | The solution for this error is to move the undispensed plate from the work area to the front buffer so that it can be properly scanned for self-inspection. This will allow the code scanner to function properly and prevent further errors from |
KM-ASSYM4-05 | 35 | M7034 | M7034-The feeding operation of the conveyor belt in the work area has timed out, please check whether the machine is jammed | Organizational Abnormality | The M7034 error message indicates that the conveyor belt feeding operation has timed out. To resolve this issue, first, check if the machine is jammed. Clear any blockages or jams from the conveyor belt. If |
KM-ASSYM4-05 | 36 | M7035 | M7035-The discharging operation of the conveyor belt in the work area has timed out, please check whether the machine is jammed | Organizational Abnormality | The solution for error M7035 is to manually check the conveyor belt for any jams or obstructions. If the belt is jammed, clear the obstruction and restart the machine. |
KM-ASSYM4-05 | 37 | M7036 | M7036-The feeding operation of the rear Buffer conveyor belt has timed out. Please check whether there is any jamming between the machine work area and the rear Buffer | Organizational Abnormality | The solution for the M7036 error is to check if there is any jamming between the machine work area and the rear Buffer, and to clear any blockages that are detected if possible. If the blockage cannot be cleared, then |
KM-ASSYM4-05 | 39 | M7038 | M7038-The left blocking cylinder in the work area rises abnormally (X40), please check whether the cylinder is stuck when rising | Organizational Abnormality | The solution for the M7038-The left blocking cylinder in the work area rises abnormally (X40) error is to check if the cylinder is stuck when rising. If the cylinder is stuck, you |
KM-ASSYM5-06 | 42 | M7041 | M7041-The lifting cylinder in the work area is abnormally descending (X32), please check whether the cylinder is stuck when descending | Organizational Abnormality | The solution for the M7041-The lifting cylinder in the work area is abnormally descending (X32) error is to check if the cylinder is stuck when descending. If it is stuck, the cyl |
KM-ASSYM5-06 | 43 | M7042 | M7042-The conveyor belt width adjustment cylinder extends abnormally (X27), please check whether the cylinder is stuck when it rises | Organizational Abnormality | The solution for the M7042 error described as "The conveyor belt width adjustment cylinder extends abnormally (X27)" is to check whether the cylinder is stuck when it rises. If the cylinder is |
KM-ASSYM5-06 | 44 | M7043 | M7043-Conveyor belt width adjustment cylinder retracts abnormally (X30), please check whether the cylinder is stuck when descending | Organizational Abnormality | The solution for M7043 errors related to the conveyor belt width adjustment cylinder retracting abnormally (X30) involves checking whether the cylinder is stuck during descent. This issue can cause damage to the convey |
KM-ASSYM5-06 | 54 | M7053 | M7053-The current glue amount is too much, please reduce it | Electronic control abnormality | Reduce the current glue amount by using less adhesive, replacing damaged parts, or adjusting the bonding process to ensure proper adhesion. In some cases, the use of a different type of adhesive or solvent may |
KM-ASSYM5-06 | 55 | M7054 | M7054-The current dispensing amount is too small, please increase | Electronic control abnormality | The error M7054 usually occurs when the dispensing amount is less than the minimum amount required. To solve this error, you need to increase the dispensing amount by adjusting the settings on your printer or using a different ink cartr |
KM-ASSYM5-06 | 65 | M7064 | M7064-X-axis servo NO readly(X14)&ERROR, please check whether the X-axis servo driver is abnormal | Electronic control abnormality | The solution to the M7064-X-axis servo NO readly(X14)&ERROR error is to check the abnormality of the X-axis servo driver. You can do this by examining the logs |
KM-ASSYM5-06 | 66 | M7065 | M7065-The right limit of the X-axis is abnormal, close to the origin end (X7), please check whether the slide table touches the limit | Electronic control abnormality | The solution for the M7065 error is to check if the slide table is touching the limit at the origin end (X7) and increase the left limit value if necessary to prevent the issue. |
KM-ASSYM5-06 | 67 | M7066 | M7066-X axis left limit is abnormal, far away from the origin end (X6), please check whether the slide table touches the limit | Electronic control abnormality | The M7066 error denotes that the left limit of the X axis is abnormal and far away from the origin end (X6). Checking whether the slide table touches the limit is recommended to solve this issue. |
KM-ASSYM5-06 | 68 | M7067 | M7067-X axis return to origin time has timed out, please check whether the slide table is abnormal or stuck | Electronic control abnormality | The error M7067 typically occurs when the X-axis slide table times out during its return to origin movement. This could be due to a malfunctioning actuator, a stuck slide table, or a problem with the home position |
KM-ASSYM5-06 | 69 | M7068 | M7068-Y-axis servo NO readly(X15)&ERROR, please check whether the X-axis servo driver is abnormal | Electronic control abnormality | The error M7068-Y-axis servo NO readly(X15)&ERROR usually indicates that there is a failure in the communication between the X-axis servo driver and the printer. To solve the problem, it |
KM-ASSYM5-06 | 70 | M7069 | M7069-Y axis front limit is abnormal, close to the origin end (X11), please check whether the slide table touches the limit | Electronic control abnormality | The solution for M7069-Y axis front limit is abnormal, close to the origin end (X11) is to check whether the slide table touches the limit. The problem could be caused by the slide table moving too far |
KM-ASSYM5-06 | 71 | M7070 | M7070-Y axis rear limit is abnormal, far away from the origin end (X10), please check whether the slide table touches the limit | Electronic control abnormality | The solution to the M7070-Y axis rear limit abnormal issue is to check if the slide table is touching the limit or if it has moved too far from the origin end (X10). If the slide table is touching |
KM-ASSYM5-06 | 72 | M7071 | M7071-Y axis return to origin time has timed out, please check whether the slide table is abnormal or stuck | Electronic control abnormality | The M7071-Y axis return to origin time has timed out error indicates that the Y-axis slide table is not responding to commands. This can be due to a stuck or abnormal condition. To troubleshoot this issue |
KM-ASSYM5-06 | 73 | M7072 | M7072-Z-axis servo NO readly(X16)&ERROR, please check whether the Z-axis servo driver is abnormal | Electronic control abnormality | The error M7072-Z-axis servo NO ready(X16)&ERROR suggests that there might be an issue with the Z-axis servo driver. The solution for this issue is to check the Z-axis serv |
KM-ASSYM5-06 | 74 | M7073 | M7073-The limit on the Z axis is abnormal, close to the origin end (X13), please check whether the slide table touches the limit | Electronic control abnormality | The solution to M7073 error that states the limit on the Z axis is abnormal, close to the origin end (X13) is to check whether the slide table touches the limit. This can be accomplished by physically inspecting |
KM-ASSYM5-06 | 75 | M7074 | M7074-Z axis lower limit abnormality, far away from the origin end (X12), please check whether the slide table touches the limit | Electronic control abnormality | The solution to the M7074-Z axis lower limit abnormality error is to perform a thorough inspection of the slide table. Verify if the slide table is touching the lower limit and make any necessary adjustments or repairs to resolve the |
KM-ASSYM5-06 | 76 | M7075 | M7075-Z axis return to origin time has timed out, please check whether the slide table is abnormal or stuck | Electronic control abnormality | To resolve the M7075 error where the Z axis return to origin has timed out, make sure to check the slide table abnormality or sticking condition. If it is normal, the problem may be with the encoder or the |
KM-ASSYM5-06 | 81 | M7080 | M7080-Upper camera identification dispensing area detection failed | Visual abnormality | The M7080 error is related to the identification of the upper camera for dispensing area detection in Toshiba Smart MRI systems. This issue may arise due to camera misalignment, obstructions, or other technical problems. |
KM-ASSYM5-06 | 82 | M7081 | M7081-PLC timed out waiting for the host computer to transmit the MARK point identification signal | Visual abnormality | The M7081-PLC timed out waiting for the host computer to transmit the MARK point identification signal error usually occurs when the PLC is unable to receive or interpret the signal from the host computer within the specified time limit. |
KM-ASSYM5-06 | 83 | M7082 | M7082-MARK point recognition failed | Visual abnormality | The solution for the M7082-MARK point recognition failed error is to reset the device's memory and perform the point recognition process again. If the issue persists, it may be necessary to consult the device's manual or contact |
KM-ASSYM5-06 | 84 | M7083 | M7083-PLC timed out waiting for the host computer to transmit the dispensing point position | Electronic control abnormality | The solution for the M7083-PLC timed out waiting for the host computer to transmit the dispensing point position error is to check the network communication between the SOPC unit and host computer, and ensure that the data transfer |
KM-ASSYM5-06 | 85 | M7084 | M7084-Scan code gun scan code NG | Electronic control abnormality | The solution to the error M7084-Scan code gun scan code NG is to check the device's internal memory for corrupt files or a missing file system partition. If the issue persists, it may be necessary to perform a |
KM-ASSYM5-06 | 86 | M7085 | M7085-TE replies card station Fail | Kazam exception | The M7085-TE replies card station fail error typically occurs when the replies card station fails to connect to the network or there is a problem with the network connection. The solution for this error may involve checking the network connection, |
KM-ASSYM5-06 | 87 | M7086 | M7086-PLC timed out while waiting for the area identification completion signal from the host computer | Visual abnormality | The solution for the M7086-PLC timed out while waiting for the area identification completion signal from the host computer is to check the settings and configuration of the communication protocol between the PLC and the host computer. Make sure that |
KM-ASSYM5-06 | 88 | M7087 | M7087-PLC timed out waiting for the host computer to send the scan code result | Machine communication abnormality | The solution for M7087-PLC error where the timed-out waiting for the host computer to send the scan code result involves verifying the host computer's network connection and IP address, updating the PLC's network |
KM-ASSYM5-06 | 89 | M7088 | M7088-PLC timed out waiting for the signal from the host computer to complete the electronic scale clearing | Visual abnormality | The problem M7088-PLC timed out waiting for the signal from the host computer to complete the electronic scale clearing could be caused by a lack of a consistent connection between the PLC and the host computer. The solution may involve |
KM-ASSYM5-06 | 90 | M7089 | M7089-PLC timed out waiting for the host computer to transmit the weighing result | Machine communication abnormality | To resolve the M7089-PLC timeout error, connect the instrument network connection to the device network connection of the host computer and ensure that the weighing result is being transmitted to a valid device. This should resolve the issue and |
KM-ASSYM5-06 | 91 | M7090 | M7090-The dispensing area detected by the upper camera is not within the range | Visual abnormality | M7090 errors usually occur when the printing head, the camera, or the paper tray is not in proper alignment. Before resolving the error, ensure that the paper tray is properly loaded, the camera is positioned correctly, and the printing |
KM-ASSYM5-06 | 92 | M7091 | M7091-Scan code OK and receive TE Read signal timeout | Kazam exception | There could be various reasons why you are encountering the M7091-Scan code OK error along with TE Read signal timeout when scanning a code. Some possible solutions include updating your firmware, ensuring that your scanner is sufficiently powered |
KM-ASSYM5-06 | 93 | M7092 | M7092-TE LINK out of range | Kazam exception | The solution for M7092-TE LINK out of range error depends on the context and the device in question. It can be resolved by adjusting the network settings, updating the firmware, or performing a hardware reset. In some |
KM-ASSYM5-06 | 94 | M7093 | M7093-TE LINK timeout | Kazam exception | The M7093-TE link timeout error typically occurs when there is a problem with the connection between two devices. To resolve this issue, you will need to check the cable connections and ensure that they are secure. If the problem persists |
KM-ASSYM5-06 | 95 | M7094 | M7094-The scan code of this site is OK, TE replies that the previous section has not passed the site or SFC failed to transmit data | Kazam exception | The solution to the error M7094 can be found by checking if the previous section of your scan has passed. If not, go to the previous section and repeat the scan. Alternatively, try to reset the SFC (Surface and |
KM-ASSYM5-06 | 96 | M7095 | M7095-The host computer did not read the READ signal sent by TE, LINK fail | Kazam exception | If you encounter the M7095 error message ("The host computer did not read the READ signal sent by TE, LINK fail"), it often indicates a problem with the network adapter or the cable connection. First, make sure that the cable |
KM-ASSYM5-06 | 97 | M7096 | M7096-Weighing machine communication abnormality | Electronic control abnormality | The M7096 error on a weighing machine indicates communication abnormality. The solution may involve resetting the machine, checking for any software updates, or contacting the manufacturer for further assistance. This issue typically occurs when the machine cannot |
KM-ASSYM5-06 | 99 | M7098 | M7098-The current position of the PCB board exceeds the safe distance, please check whether the PCB board is placed properly | Other exceptions | The error M7098 indicates that the PCB board is not placed properly. This issue can be resolved by rechecking the PCB board's position and ensuring that it is within the safe distance allowed for PCB placement. If |
KM-ASSYM5-06 | 101 | M7100 | M7100-When starting the machine, please clean the scale pan first and click the Cleared button before starting the machine. | Abnormal personnel operation | The solution to the M7100 error when starting the machine is to clean the scale pan and click the Cleared button before starting the machine. This will ensure that the scale is accurate and ready for use. |
KM-ASSYM5-06 | 102 | M7101 | M7101-Please clean the scale pan and press the "Scale Pan Easy Clean Button" | Abnormal personnel operation | The solution for the error M7101 is to clean the scale pan using a cleaning tool provided by the scale manufacturer, and then to press the "Scale Pan Easy Clean Button" to reset the scale. If the problem persists, the |
KM-ASSYM5-06 | 103 | M7102 | M7102-Weighing machine reset failed | Electronic control abnormality | M7102-Weighing machine reset failed error typically occurs when the machine cannot initialize due to an incorrect password or issue with its software. To resolve this, consult the owner manual for instructions on resetting the machine and updating its firm |
KM-ASSYM5-06 | 113 | M7112 | M7112-Visual software model number is inconsistent with PLC model number | Visual abnormality | The solution to the M7112 error is to check that the visual software model number matches the PLC model number. If both numbers are correct, then the error may be caused by a mismatch between the cable connections, power supply, |
KM-ASSYM5-06 | 114 | M7113 | M7113-Current discharging point index is out of range | Visual abnormality | The solution to the M7113 error involves updating the current discharging point settings on the device in question to within the specified range. This can typically be done through the device's user manual or settings interface. If the issue pers |
KM-ASSYM5-06 | 116 | M7115 | M7115-The discharge point exceeds the index range | Visual abnormality | The error "M7115-The discharge point exceeds the index range" indicates a problem in the discharge of stored procedures. To resolve this issue, you can check the discharge point value and modify it within the index range |
KM-ASSYM5-06 | 117 | M7116 | M7116-Timeout waiting for next action | Machine communication abnormality | The M7116-Timeout waiting for next action error typically occurs when a software process is awaiting user input or a system event but is not receiving it within a specified timeout period. The solution may involve increasing the timeout limit, optimizing |
KM-ASSYM5-06 | 118 | M7117 | M7117-The number of required assemblies is more than the number of positioned cameras | Other exceptions | The M7117 error occurs when the number of required assemblies exceeds the number of positioned cameras in a camera-based manufacturing process. To resolve this issue, you can either increase the number of positioned cameras or optimize the assembly |
KM-ASSYM3-04 | 6 | M7007 | Alarm: pressing position blocked_sensor double lights | Organizational Abnormality | There are several possible causes for this error, including a malfunctioning light sensor or an issue with the camera. However, the most common solution is to clean the affected area thoroughly and try again. If the problem persists, contact the manufacturer or |
KM-ASSYM3-04 | 32 | M7044 | Alarm: During initialization, the assembly line materials were not cleared. | Abnormal personnel operation | To resolve the "Alarm: During initialization, the assembly line materials were not cleared." error, ensure that all materials are properly placed and cleared from the assembly line before beginning operations. This can prevent any potential issues during the initial setup of the production |
KM-ASSYM3-05 | 1 | M70 | M70-The left labeling machine is out of material | Abnormal personnel operation | This error often occurs when the labeling machine runs out of labels or label stock. To solve it, ensure that the label machine has enough labels or label stock, and that the labels are properly loaded into the machine. Check the machine's settings |
KM-ASSYM3-05 | 2 | M71 | M71-The right labeling machine is out of material | Abnormal personnel operation | To solve error M71-The right labeling machine is out of material, first, check to ensure that the correct labeling machine is in use and has sufficient material. If the machine is running low, you can either restock it or |
KM-ASSYM3-05 | 3 | M72 | M72-The operation of the left label discharging machine has timed out, please check the label discharging machine | Electronic control abnormality | "The left label discharging machine has experienced a timeout Error M72. For assistance, please verify the label discharging machine's operation and adjust settings or contact system support for further troubleshooting." |
KM-ASSYM3-05 | 4 | M73 | M73-The operation of the right label dispensing machine has timed out, please check the label discharging machine | Electronic control abnormality | To solve the issue of M73-timed out error in the label dispensing machine, first, the user should check the label discharging machine to ensure that it is functioning correctly. If issues are found, troubleshoot them before |
KM-ASSYM3-05 | 5 | M74 | There is no feedback in the communication between M74-PLC and CCD, please restart the CCD part | Visual abnormality | The solution to this issue could potentially be to restart the CCD part, which could communicate with the M74-PLC and provide feedback. However, it's important to take note that this is just one possible solution and other underlying issues |
KM-ASSYM3-05 | 6 | M75 | M75-Start detecting that there is material in the work area, please select the work area status | Abnormal personnel operation | The solution for the M75-Start error is to select the work area status as "Clear" before starting the machine. If the work area is not clear, the machine will not start and will display this error message. |
KM-ASSYM3-05 | 11 | M80 | M80-EMO&&DOOR is on. Please check the safety door and emergency stop switch (X14) | Abnormal personnel operation | The solution for the error M80-EMO&&DOOR is on. Please check the safety door and emergency stop switch (X14) involves resetting the emergency stop button and ensuring that the safety door is closed before starting the machine |
KM-ASSYM3-05 | 12 | M81 | M81-Equipment model setting is abnormal, please set the model | Abnormal personnel operation | To resolve the error M81-Equipment model setting is abnormal, please set the model, follow these steps:
1. Identify the equipment in question.
2. Determine the correct model number for the equipment. |
KM-ASSYM3-05 | 13 | M82 | M82-Please press the reset button before starting the automatic process | Abnormal personnel operation | The solution to the M82 error described as "Please press the reset button before starting the automatic process" is to press the reset button and then restart the device or application that is producing the error. This will often clear any corrupted files or |
KM-ASSYM3-05 | 14 | M83 | M83-The device has not returned to the origin, please execute the device to return to the origin first | Abnormal personnel operation | The solution to the M83 error is to perform a device initialization or power cycle by turning off the radio and then back on to reset the device's location and return it to its starting point. |
KM-ASSYM3-05 | 15 | M84 | The communication connection between M84-PLC1 and PLC2 is interrupted | Machine communication abnormality | The solution for the error described as "The communication connection between M84-PLC1 and PLC2 is interrupted" may involve checking the communication protocols, ensuring proper termination of the connection, checking the modems and communication cards, |
KM-ASSYM3-05 | 17 | M86 | M86-Front buffer conveyor belt feeding operation timeout | Organizational Abnormality | The solution for the error M86-Front buffer conveyor belt feeding operation timeout is to clean the belt, tighten any loose connections, and ensure proper alignment between components. If the issue persists, check for blockages and repair or replace |
KM-ASSYM3-05 | 18 | M87 | M87-Front buffer conveyor belt discharging operation timeout | Organizational Abnormality | The solution for the M87-Front buffer conveyor belt discharging operation timeout error could involve checking the connection between the conveyor belt and the motor, ensuring the belt speed is appropriate, and verifying that there are no obstructions in |
KM-ASSYM3-05 | 19 | M88 | M88-Work area inlet conveyor belt operation timeout | Organizational Abnormality | The solution for the M88-Work area inlet conveyor belt operation timeout error could involve adjusting the conveyor belt speed, updating or replacing the equipment, or contacting the manufacturer for assistance. Regular maintenance can also help prevent this error |
KM-ASSYM3-05 | 20 | M89 | M89-Work area discharging conveyor belt operation timeout | Organizational Abnormality | The solution to the M89-Work area discharging conveyor belt operation timeout error typically involves cleaning the belt and belt feeder, removing blockages, and adjusting the conveyor speed. If the error persists, you may need |
KM-ASSYM3-05 | 21 | M90 | M90-Rear buffer conveyor belt feeding operation timeout | Organizational Abnormality | Solution to M90-Rear buffer conveyor belt feeding operation timeout error is to increase the dwell time or use a higher-capacity buffer to allow the belt more time to feed the product. If the error persists, ensure that the belt |
KM-ASSYM3-05 | 22 | M91 | M91-Rear buffer conveyor belt discharging operation timeout | Organizational Abnormality | The solution for the M91-Rear buffer conveyor belt discharging operation timeout error may involve several troubleshooting steps. These steps could include checking the conveyor belt’s condition; enabling or disabling the rear buffer convey |
KM-ASSYM3-05 | 23 | M92 | M92-The operation of the left label discharging machine has timed out, please check the label discharging machine | Electronic control abnormality | The solution for the M92 error is recommended to check the label discharging machine for an issue preventing it from functioning properly, or contact technical support for further assistance. |
KM-ASSYM3-05 | 24 | M93 | M93-The operation of the right label dispensing machine has timed out, please check the label discharging machine | Electronic control abnormality | The solution for the M93 error is to check the label discharging machine and ensure that it is functioning properly. The issue could be caused by a paper jam or other problem with the machine, which is delaying the dispensing process and |
KM-ASSYM3-05 | 25 | M94 | M94- Abnormal rise of blocking cylinder in work area (X20) | Organizational Abnormality | The M94 error code indicates a problem with the blocking cylinder in the work area. To fix this, follow these steps: Check that all the blocking cylinders are functioning properly and that no obstacles are blocking the work area. If |
KM-ASSYM3-05 | 26 | M95 | M95- Abnormal descent of blocking cylinder in work area (X21) | Organizational Abnormality | The solution for M95- Abnormal descent of blocking cylinder in work area (X21) error involves checking the hydraulic cylinder, adjusting the screws and bushings, replacing or repairing the worn parts, |
KM-ASSYM3-05 | 27 | M96 | M96- Abnormal rise of jacking cylinder in work area (X22) | Organizational Abnormality | The solution for the M96 error code "Abnormal rise of jacking cylinder in work area (X22)" would typically involve performing a thorough inspection of the equipment to identify any faulty components or loose connections. Once the cause of |
KM-ASSYM3-05 | 28 | M97 | M97 - Abnormal descent of jacking cylinder in work area (X23) | Organizational Abnormality | The solution for M97 Abnormal descent of jacking cylinder in work area (X23) is to inspect the jacking cylinder and its components for damage or defects, and ensure proper maintenance and safe operation of the jacking |
KM-ASSYM3-05 | 35 | M104 | M104-X axis servo NO readly & ERROR (X10) | Electronic control abnormality | The solution for the M104-X axis servo NO readly and ERROR (X10) can vary depending on the specific issue, but it often involves checking the connections between the servo and the motherboard, confirming that |
KM-ASSYM3-05 | 36 | M105 | M105-X axis left limit abnormality (X5) | Electronic control abnormality | The M105 error occurs when the X-axis left limit is exceeded during printing, usually resulting from a print bed issue or a loose cable connection. To solve this error, you can adjust the bed leveling, check for loose connections |
KM-ASSYM3-05 | 37 | M106 | M106-X axis right limit abnormality (X4) | Electronic control abnormality | The solution for the error "M106-X axis right limit abnormality (X4)" usually involves adjusting the position of the print bed or the extruder to ensure that the X-axis is not touching the right limit |
KM-ASSYM3-05 | 38 | M107 | M107-X axis return to origin time timeout | Electronic control abnormality | The error M107-X axis return to origin timeout indicates that the machine is experiencing a timing issue while returning to the origin position. This error typically occurs when there is a problem with the encoder or motor that is causing the axis to |
KM-ASSYM4-05 | 40 | M7039 | M7039-The left blocking cylinder in the work area is abnormally descending (X41), please check whether the cylinder is stuck when descending | Organizational Abnormality | The error message M7039-The left blocking cylinder in the work area is abnormally descending (X41), please check whether the cylinder is stuck when descending indicates that there is an issue on a cylinder |
KM-ASSYM4-05 | 41 | M7040 | M7040-The right blocking cylinder in the work area rises abnormally (X42), please check whether the cylinder is stuck when rising | Organizational Abnormality | The solution to the M7040-The right blocking cylinder in the work area rises abnormally (X42) error is to check if the cylinder is stuck when rising. If the cylinder is stuck, it |
KM-ASSYM4-05 | 42 | M7041 | M7041-The right blocking cylinder in the work area is abnormally descending (X43), please check whether the cylinder is stuck when descending | Organizational Abnormality | The M7041 error message indicates that the right blocking cylinder is descending abnormally and could be stuck. The solution is to check the cylinder for possible mechanical or electrical issues, such as worn or damaged seals, fault |
KM-ASSYM4-05 | 43 | M7042 | M7042-The jacking cylinder in the work area rises abnormally (X44), please check whether the cylinder is stuck when rising | Organizational Abnormality | The M7042 error occurs when the jacking cylinder in the work area rises abnormally. To resolve the error, check if the cylinder is stuck when it rises. If it is, try to release the cyl |
KM-ASSYM4-05 | 44 | M7043 | M7043-The lifting cylinder in the work area is abnormally descending (X45), please check whether the cylinder is stuck when descending | Organizational Abnormality | The solution for the M7043 error is to check the lifting cylinder for any abnormalities and ensure that it is functioning properly. This may involve troubleshooting or disassembling and reassembling the cylinder depending on |
KM-ASSYM4-05 | 49 | M7048 | M7048-The cylinder of the left glue cylinder in the slide area is rising abnormally (X50), please check whether the cylinder is stuck when rising | Organizational Abnormality | If the left glue cylinder in the slide area is rising abnormally and showing error code M7048, it's possible that the cylinder is stuck. To resolve this issue, you can try applying a gentle pressure on |
KM-ASSYM4-05 | 51 | M7050 | M7050-The cylinder of the right glue cylinder in the slide area is rising abnormally (X55), please check whether the cylinder is stuck when rising | Organizational Abnormality | The M7050 error indicates that the right glue cylinder in the slide area is rising abnormally. To diagnose the issue, check whether the cylinder is stuck when rising. If it is, then the solution is to |
KM-ASSYM4-05 | 52 | M7051 | M7051-The cylinder of the right glue cylinder in the slide area is abnormally descending (X61), please check whether the cylinder is stuck when descending | Organizational Abnormality | The M7051 error message indicates that the cylinder in the slide area is descending abnormally. This issue could be caused by the cylinder becoming stuck while descending. To resolve this, check the cylinder for any block |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.