Daily Papers

We consider dynamic stair climbing with the HRP-4 humanoid robot as part of an Airbus manufacturing use-case demonstrator. We share experimental knowledge gathered so as to achieve this task, which HRP-4 had never been challenged to before. In particular, we extend walkingstabilization based on linear inverted pendulum tracking by quadratic programming-based wrench distribution and a whole-body admittance controller that applies both end-effector and CoM strategies. While existing stabilizers tend to use either one or the other, our experience suggests that the combination of these two approaches improves tracking performance. We demonstrate this solution in an on-site experiment where HRP-4 climbs an industrial staircase with 18.5 cm high steps, and release our walking controller as open source software.

It is well-known that inverse dynamics models can improve tracking performance in robot control. These models need to precisely capture the robot dynamics, which consist of well-understood components, e.g., rigid body dynamics, and effects that remain challenging to capture, e.g., stick-slip friction and mechanical flexibilities. Such effects exhibit hysteresis and partial observability, rendering them, particularly challenging to model. Hence, hybrid models, which combine a physical prior with data-driven approaches are especially well-suited in this setting. We present a novel hybrid model formulation that enables us to identify fully physically consistent inertial parameters of a rigid body dynamics model which is paired with a recurrent neural network architecture, allowing us to capture unmodeled partially observable effects using the network memory. We compare our approach against state-of-the-art inverse dynamics models on a 7 degree of freedom manipulator. Using data sets obtained through an optimal experiment design approach, we study the accuracy of offline torque prediction and generalization capabilities of joint learning methods. In control experiments on the real system, we evaluate the model as a feed-forward term for impedance control and show the feedback gains can be drastically reduced to achieve a given tracking accuracy.

This letter presents an analytical linear parameter-varying (LPV) representation of quadrotor dynamics utilizing Koopman theory, facilitating computationally efficient linear model predictive control (LMPC) for real-time trajectory tracking. By leveraging carefully designed Koopman observables, the proposed approach enables a compact lifted-space evolution that mitigates the curse of dimensionality while preserving the nonlinear characteristics of the system. Although model predictive control (MPC) is a powerful strategy for quadrotor control, it faces a trade-off between the high computational cost of nonlinear MPC (NMPC) and the reduced accuracy of LMPC. To address this gap, we introduce KQ-LMPC (Koopman Quasilinear LPV MPC), which leverages the Koopman-lifted LPV formulation to enforce constraints, ensure lower computational burden and real-time feasibility, and deliver tracking performance comparable to NMPC. Experimental validation confirms the effectiveness of the framework in reasonably agile flight. To the best of our knowledge, this is the first experimentally validated LMPC for quadrotors that employs analytically derived Koopman observables without requiring training data.

Even for known nonlinear dynamical systems, feedback controller synthesis is a difficult problem that often requires leveraging the particular structure of the dynamics to induce a stable closed-loop system. For general nonlinear models, including those fit to data, there may not be enough known structure to reliably synthesize a stabilizing feedback controller. In this paper, we discuss a state-dependent nonlinear tracking controller formulation based on a state-dependent Riccati equation for general nonlinear control-affine systems. This formulation depends on a nonlinear factorization of the system of vector fields defining the control-affine dynamics, which always exists under mild smoothness assumptions. We propose a method for learning this factorization from a finite set of data. On a variety of simulated nonlinear dynamical systems, we empirically demonstrate the efficacy of learned versions of this controller in stable trajectory tracking. Alongside our learning method, we evaluate recent ideas in jointly learning a controller and stabilizability certificate for known dynamical systems; we show experimentally that such methods can be frail in comparison.

We address the challenge of developing a generalizable neural tracking controller for dexterous manipulation from human references. This controller aims to manage a dexterous robot hand to manipulate diverse objects for various purposes defined by kinematic human-object interactions. Developing such a controller is complicated by the intricate contact dynamics of dexterous manipulation and the need for adaptivity, generalizability, and robustness. Current reinforcement learning and trajectory optimization methods often fall short due to their dependence on task-specific rewards or precise system models. We introduce an approach that curates large-scale successful robot tracking demonstrations, comprising pairs of human references and robot actions, to train a neural controller. Utilizing a data flywheel, we iteratively enhance the controller's performance, as well as the number and quality of successful tracking demonstrations. We exploit available tracking demonstrations and carefully integrate reinforcement learning and imitation learning to boost the controller's performance in dynamic environments. At the same time, to obtain high-quality tracking demonstrations, we individually optimize per-trajectory tracking by leveraging the learned tracking controller in a homotopy optimization method. The homotopy optimization, mimicking chain-of-thought, aids in solving challenging trajectory tracking problems to increase demonstration diversity. We showcase our success by training a generalizable neural controller and evaluating it in both simulation and real world. Our method achieves over a 10% improvement in success rates compared to leading baselines. The project website with animated results is available at https://meowuu7.github.io/DexTrack/.

A common pipeline in learning-based control is to iteratively estimate a model of system dynamics, and apply a trajectory optimization algorithm - e.g.~iLQR - on the learned model to minimize a target cost. This paper conducts a rigorous analysis of a simplified variant of this strategy for general nonlinear systems. We analyze an algorithm which iterates between estimating local linear models of nonlinear system dynamics and performing iLQR-like policy updates. We demonstrate that this algorithm attains sample complexity polynomial in relevant problem parameters, and, by synthesizing locally stabilizing gains, overcomes exponential dependence in problem horizon. Experimental results validate the performance of our algorithm, and compare to natural deep-learning baselines.

Recently, learning-based controllers have been shown to push mobile robotic systems to their limits and provide the robustness needed for many real-world applications. However, only classical optimization-based control frameworks offer the inherent flexibility to be dynamically adjusted during execution by, for example, setting target speeds or actuator limits. We present a framework to overcome this shortcoming of neural controllers by conditioning them on an auxiliary input. This advance is enabled by including a feature-wise linear modulation layer (FiLM). We use model-free reinforcement-learning to train quadrotor control policies for the task of navigating through a sequence of waypoints in minimum time. By conditioning the policy on the maximum available thrust or the viewing direction relative to the next waypoint, a user can regulate the aggressiveness of the quadrotor's flight during deployment. We demonstrate in simulation and in real-world experiments that a single control policy can achieve close to time-optimal flight performance across the entire performance envelope of the robot, reaching up to 60 km/h and 4.5g in acceleration. The ability to guide a learned controller during task execution has implications beyond agile quadrotor flight, as conditioning the control policy on human intent helps safely bringing learning based systems out of the well-defined laboratory environment into the wild.

Achieving a desired impedance during physical interaction remains a central problem in compliant control. In many practical implementations, admittance control combined with linear position controllers is employed, but this structure typically results in only approximate impedance behavior. This paper establishes a rigorous equivalence between the impedance realization problem and the generalized output regulation theory, and shows that, under the admittance architecture and assuming the inner position controller is restricted to linear combinations of commonly used signals, a unique control law exists that achieves exact compliant control. The resulting controller introduces additional terms with respect to a conventional PD formulation, while preserving a simple structure. Numerical simulations are used to illustrate the effectiveness of the proposed approach under nominal conditions and in the presence of model uncertainties, and to compare its performance against a standard PD controller. The results demonstrate improved interaction performance and robustness, supporting the theoretical analysis.

The integration of Supernumerary Limbs (SLs) on humanoid robots poses a significant stability challenge due to the dynamic perturbations they introduce. This thesis addresses this issue by designing a novel hierarchical control architecture to improve humanoid locomotion stability with SLs. The core of this framework is a decoupled strategy that combines learning-based locomotion with model-based balancing. The low-level component consists of a walking gait for a Unitree H1 humanoid through imitation learning and curriculum learning. The high-level component actively utilizes the SLs for dynamic balancing. The effectiveness of the system is evaluated in a physics-based simulation under three conditions: baseline gait for an unladen humanoid (baseline walking), walking with a static SL payload (static payload), and walking with the active dynamic balancing controller (dynamic balancing). Our evaluation shows that the dynamic balancing controller improves stability. Compared to the static payload condition, the balancing strategy yields a gait pattern closer to the baseline and decreases the Dynamic Time Warping (DTW) distance of the CoM trajectory by 47\%. The balancing controller also improves the re-stabilization within gait cycles and achieves a more coordinated anti-phase pattern of Ground Reaction Forces (GRF). The results demonstrate that a decoupled, hierarchical design can effectively mitigate the internal dynamic disturbances arising from the mass and movement of the SLs, enabling stable locomotion for humanoids equipped with functional limbs. Code and videos are available here: https://github.com/heyzbw/HuSLs.

This paper addresses the task of modeling Deformable Linear Objects (DLOs), such as ropes and cables, during dynamic motion over long time horizons. This task presents significant challenges due to the complex dynamics of DLOs. To address these challenges, this paper proposes differentiable Discrete Elastic Rods For deformable linear Objects with Real-time Modeling (DEFORM), a novel framework that combines a differentiable physics-based model with a learning framework to model DLOs accurately and in real-time. The performance of DEFORM is evaluated in an experimental setup involving two industrial robots and a variety of sensors. A comprehensive series of experiments demonstrate the efficacy of DEFORM in terms of accuracy, computational speed, and generalizability when compared to state-of-the-art alternatives. To further demonstrate the utility of DEFORM, this paper integrates it into a perception pipeline and illustrates its superior performance when compared to the state-of-the-art methods while tracking a DLO even in the presence of occlusions. Finally, this paper illustrates the superior performance of DEFORM when compared to state-of-the-art methods when it is applied to perform autonomous planning and control of DLOs. Project page: https://roahmlab.github.io/DEFORM/.

Human demonstrations provide strong priors for robot manipulation, yet it is non-trivial to transfer them to execute on real robots due to the kinematic gap. In dexterous manipulation, it remains challenging to track long-horizon, contact-rich sequences even in simulators: a reference-tracking policy must keep objects on their target trajectories while preserving demonstrated joint motion and contact timing. Existing approaches often rely on hand-crafted reward tuning that require per-sequence tuning and break under limited interaction budgets. We introduce ConTrack, a reinforcement learning (RL) framework that scales with tracking data. ConTrack treats object tracking as a constraint and allocates remaining control authority to motion fidelity, which allows it to adapt task--style trade-offs online using a dual-variable update. In addition, ConTrack also stabilizes long-horizon learning with an adaptive mid-trajectory reset library that reuses policy-reachable simulator states. Our qualitative and quantitative results in simulation tracking and real robot demonstrate that ConTrack improves success and object pose accuracy significantly over prior arts while preserving joint and contact fidelity. Website: https://www.lyt0112.com/projects/ConTrack.

Motion trajectories offer reliable references for physics-based motion learning but suffer from sparsity, particularly in regions that lack sufficient data coverage. To address this challenge, we introduce a self-supervised, structured representation and generation method that extracts spatial-temporal relationships in periodic or quasi-periodic motions. The motion dynamics in a continuously parameterized latent space enable our method to enhance the interpolation and generalization capabilities of motion learning algorithms. The motion learning controller, informed by the motion parameterization, operates online tracking of a wide range of motions, including targets unseen during training. With a fallback mechanism, the controller dynamically adapts its tracking strategy and automatically resorts to safe action execution when a potentially risky target is proposed. By leveraging the identified spatial-temporal structure, our work opens new possibilities for future advancements in general motion representation and learning algorithms.

This paper presents Elevator-LIO, a LiDAR-inertial odometry framework designed to achieve continuous robot localization during elevator travel, thereby supporting cross-floor robotic tasks. To address the state-estimation problem in non-inertial frames, Elevator-LIO establishes a decoupled state-estimation model that separately models the robot motion relative to the elevator and the elevator motion itself, and embeds it into a mode-dependent iterated error-state Kalman filter framework. This framework degenerates to conventional LIO estimation in ordinary indoor environments, while enabling the propagation and constrained update of elevator-related states in elevator non-inertial environments, thereby achieving continuous and stable localization. An elevator mode manager detects elevator entry and exit events using LiDAR ranging statistics and estimated states, and introduces event-triggered zero-velocity and zero-acceleration updates when the elevator stops to suppress accumulated vertical drift. In addition, this paper adopts an adaptive voxel downsampling strategy to maintain a stable number of effective points under significant environmental scale changes. We conduct extensive experiments on 20 real-world sequences containing 79 elevator rides, including practical challenges such as large-scale spaces, long vertical travel, dynamic pedestrian interference, and mirror reflections. The results show that Elevator-LIO maintains continuous localization accuracy in all sequences, with terminal height error below 1 cm in 17 sequences. In contrast, existing representative localization systems perform poorly on these elevator sequences. Tests on the Hilti 2022/2023 datasets further show that the proposed method remains competitive in standard indoor scenarios. The project page is available at https://xiaofan4122.github.io/Elevator_LIO_Page/.

Harmonic model predictive control (HMPC) is a recent model predictive control (MPC) formulation for tracking piece-wise constant references that includes a parameterized artificial harmonic reference as a decision variable, resulting in an increased performance and domain of attraction with respect to other MPC formulations. This article presents an extension of the HMPC formulation to track periodic harmonic/sinusoidal references and discusses its use for tracking arbitrary trajectories. The proposed formulation inherits the benefits of its predecessor, namely its good performance and large domain of attraction when using small prediction horizons, and that the complexity of its optimization problem does not depend on the period of the reference. We show closed-loop results discussing its performance and comparing it to other MPC formulations.

Deep reinforcement learning (DRL) is a promising approach to solve complex control tasks by learning policies through interactions with the environment. However, the training of DRL policies requires large amounts of training experiences, making it impractical to learn the policy directly on physical systems. Sim-to-real approaches leverage simulations to pretrain DRL policies and then deploy them in the real world. Unfortunately, the direct real-world deployment of pretrained policies usually suffers from performance deterioration due to the different dynamics, known as the reality gap. Recent sim-to-real methods, such as domain randomization and domain adaptation, focus on improving the robustness of the pretrained agents. Nevertheless, the simulation-trained policies often need to be tuned with real-world data to reach optimal performance, which is challenging due to the high cost of real-world samples. This work proposes a distributed cloud-edge architecture to train DRL agents in the real world in real-time. In the architecture, the inference and training are assigned to the edge and cloud, separating the real-time control loop from the computationally expensive training loop. To overcome the reality gap, our architecture exploits sim-to-real transfer strategies to continue the training of simulation-pretrained agents on a physical system. We demonstrate its applicability on a physical inverted-pendulum control system, analyzing critical parameters. The real-world experiments show that our architecture can adapt the pretrained DRL agents to unseen dynamics consistently and efficiently.

Spacecraft rendezvous on elliptical orbits must hold a safety corridor under navigation noise, unmodelled perturbations, and thrust errors driven by propellant mass uncertainty. This paper develops a tube-based model predictive controller for the Yamanaka-Ankersen linear time-varying dynamics, carrying constraint-tightening tube methods from circular to elliptical orbits. A horizon-dependent, element-wise error bound propagates the actual closed-loop matrices along the prediction window, so early prediction steps keep nearly the full corridor that a constant-width tube would surrender. A multiplicative-to-additive conversion folds mass and thrust uncertainty into the same tightening recursion, and a Perron-Frobenius spectral-radius condition supplies a computable certificate that the tightening converges, with an explicit input-to-state stability gain. In a paired Monte Carlo campaign on a Mars sample-return orbit, the tube controller cuts mean corridor violations by more than an order of magnitude against a nominal predictive baseline at comparable fuel cost. A nonlinear truth-model test with oblateness perturbations well beyond the assumed disturbance budget leaves the corridor unviolated, and when the design envelope is exceeded the tightened problem becomes infeasible and the controller reverts to a saturated linear fallback, making the loss of guarantee explicit rather than silent. The construction requires only element-wise arithmetic and an open-source quadratic-programming solver.

Hybrid systems are prevalent in robotics. However, ensuring the stability of hybrid systems is challenging due to sophisticated continuous and discrete dynamics. A system with all its system modes stable can still be unstable. Hence special treatments are required at mode switchings to stabilize the system. In this work, we propose a hierarchical, neural network (NN)-based method to control general hybrid systems. For each system mode, we first learn an NN Lyapunov function and an NN controller to ensure the states within the region of attraction (RoA) can be stabilized. Then an RoA NN estimator is learned across different modes. Upon mode switching, we propose a differentiable planner to ensure the states after switching can land in next mode's RoA, hence stabilizing the hybrid system. We provide novel theoretical stability guarantees and conduct experiments in car tracking control, pogobot navigation, and bipedal walker locomotion. Our method only requires 0.25X of the training time as needed by other learning-based methods. With low running time (10-50X faster than model predictive control (MPC)), our controller achieves a higher stability/success rate over other baselines such as MPC, reinforcement learning (RL), common Lyapunov methods (CLF), linear quadratic regulator (LQR), quadratic programming (QP) and Hamilton-Jacobian-based methods (HJB). The project page is on https://mit-realm.github.io/hybrid-clf.

Multi-agent systems (MASs) can autonomously learn to solve previously unknown tasks by means of each agent's individual intelligence as well as by collaborating and exploiting collective intelligence. This article considers a group of autonomous agents learning to track the same given reference trajectory in a possibly small number of trials. We propose a novel collective learning control method that combines iterative learning control (ILC) with a collective update strategy. We derive conditions for desirable convergence properties of such systems. We show that the proposed method allows the collective to combine the advantages of the agents' individual learning strategies and thereby overcomes trade-offs and limitations of single-agent ILC. This benefit is achieved by designing a heterogeneous collective, i.e., a different learning law is assigned to each agent. All theoretical results are confirmed in simulations and experiments with two-wheeled-inverted-pendulum robots (TWIPRs) that jointly learn to perform the desired maneuver.

An invariant extended Kalman filter (IEKF) is developed for state estimation of serial rigid manipulators with an arbitrary number of links, formulated entirely within the Lie group SE(3). The group-affine property of the kinematic equations makes the linearised error dynamics autonomous, so the Riccati equation governs the true error covariance rather than a local approximation. A physically separated noise model treats gyroscope and accelerometer channels independently: the accelerometer provides translational twist via gravity-compensated integration, yielding a measurement covariance that scales with the sample interval in exact analogy with process noise discretisation; a state-dependent Coriolis noise term captures gyroscope noise propagating through the nonlinear dynamics, vanishing at rest and growing with twist magnitude. The filter is structured as a modular chain of per-link IEKFs in which the predicted covariance of each link depends on its predecessor only through the Adjoint-transformed posterior, giving linear computational cost in link count. Exponential ultimate boundedness in mean square is established via a Lie algebra Lyapunov function, with per-link bounds chained through the Adjoint operator norm to yield a stability certificate that is modular and scalable to arbitrary chain length. Numerical results validate the design.

Inference-time LLM alignment methods, particularly activation steering, offer an alternative to fine-tuning by directly modifying activations during generation. Existing methods, however, often rely on non-anticipative interventions that ignore how perturbations propagate through transformer layers and lack online error feedback, resulting in suboptimal, open-loop control. To address this, we show empirically that, despite the nonlinear structure of transformer blocks, layer-wise dynamics across multiple LLM architectures and scales are well-approximated by locally-linear models. Exploiting this property, we model LLM inference as a linear time-varying dynamical system and adapt the classical linear quadratic regulator to compute feedback controllers using layer-wise Jacobians, steering activations toward desired semantic setpoints in closed-loop with minimal computational overhead and no offline training. We also derive theoretical bounds on setpoint tracking error, enabling formal guarantees on steering performance. Using a novel adaptive semantic feature setpoint signal, our method yields robust, fine-grained behavior control across models, scales, and tasks, including state-of-the-art modulation of toxicity, truthfulness, refusal, and arbitrary concepts, surpassing baseline steering methods. Our code is available at: https://github.com/trustworthyrobotics/lqr-activation-steering

Swarm aerial robots are required to maintain close proximity to successfully traverse narrow areas in cluttered environments. However, this movement is affected by the downwash effect generated from other quadrotors in the swarm. This aerodynamic effect is highly nonlinear and hard to describe through mathematical modeling. Additionally, the existence of the downwash disturbance can be predicted based on the states of neighboring quadrotors. If this prediction is considered, the control loop can proactively handle the disturbance, resulting in improved performance. To address these challenges, we propose an approach that integrates a Neural network Downwash Predictor with Nonlinear Model Predictive Control (NDP-NMPC). The neural network is trained with spectral normalization to ensure robustness and safety in uncollected cases. The predicted disturbances are then incorporated into the optimization scheme in NMPC, which enforces constraints to ensure that states and inputs remain within safe limits. We also design a quadrotor system, identify its parameters, and implement the proposed method on board. Finally, we conduct a prediction experiment to validate the safety and effectiveness of the network. In addition, a real-time trajectory tracking experiment is performed with the entire system, demonstrating a 75.37% reduction in tracking error in height under the downwash effect.

Ensuring safety is of paramount importance in physical human-robot interaction applications. This requires both adherence to safety constraints defined on the system state, as well as guaranteeing compliant behavior of the robot. If the underlying dynamical system is known exactly, the former can be addressed with the help of control barrier functions. The incorporation of elastic actuators in the robot's mechanical design can address the latter requirement. However, this elasticity can increase the complexity of the resulting system, leading to unmodeled dynamics, such that control barrier functions cannot directly ensure safety. In this paper, we mitigate this issue by learning the unknown dynamics using Gaussian process regression. By employing the model in a feedback linearizing control law, the safety conditions resulting from control barrier functions can be robustified to take into account model errors, while remaining feasible. In order to enforce them on-line, we formulate the derived safety conditions in the form of a second-order cone program. We demonstrate our proposed approach with simulations on a two-degree-of-freedom planar robot with elastic joints.

We present Kinodynamic RRT*, an incremental sampling-based approach for asymptotically optimal motion planning for robots with linear differential constraints. Our approach extends RRT*, which was introduced for holonomic robots (Karaman et al. 2011), by using a fixed-final-state-free-final-time controller that exactly and optimally connects any pair of states, where the cost function is expressed as a trade-off between the duration of a trajectory and the expended control effort. Our approach generalizes earlier work on extending RRT* to kinodynamic systems, as it guarantees asymptotic optimality for any system with controllable linear dynamics, in state spaces of any dimension. Our approach can be applied to non-linear dynamics as well by using their first-order Taylor approximations. In addition, we show that for the rich subclass of systems with a nilpotent dynamics matrix, closed-form solutions for optimal trajectories can be derived, which keeps the computational overhead of our algorithm compared to traditional RRT* at a minimum. We demonstrate the potential of our approach by computing asymptotically optimal trajectories in three challenging motion planning scenarios: (i) a planar robot with a 4-D state space and double integrator dynamics, (ii) an aerial vehicle with a 10-D state space and linearized quadrotor dynamics, and (iii) a car-like robot with a 5-D state space and non-linear dynamics.

Long-horizon whole-body humanoid teleoperation remains challenging due to accumulated global pose drift, particularly on full-sized humanoids. Although recent learning-based tracking methods enable agile and coordinated motions, they typically operate in the robot's local frame and neglect global pose feedback, leading to drift and instability during extended execution. In this work, we present CLOT, a real-time whole-body humanoid teleoperation system that achieves closed-loop global motion tracking via high-frequency localization feedback. CLOT synchronizes operator and robot poses in a closed loop, enabling drift-free human-to-humanoid mimicry over long timehorizons. However, directly imposing global tracking rewards in reinforcement learning, often results in aggressive and brittle corrections. To address this, we propose a data-driven randomization strategy that decouples observation trajectories from reward evaluation, enabling smooth and stable global corrections. We further regularize the policy with an adversarial motion prior to suppress unnatural behaviors. To support CLOT, we collect 20 hours of carefully curated human motion data for training the humanoid teleoperation policy. We design a transformer-based policy and train it for over 1300 GPU hours. The policy is deployed on a full-sized humanoid with 31 DoF (excluding hands). Both simulation and real-world experiments verify high-dynamic motion, high-precision tracking, and strong robustness in sim-to-real humanoid teleoperation. Motion data, demos and code can be found in our website.

A common belief in model-free reinforcement learning is that methods based on random search in the parameter space of policies exhibit significantly worse sample complexity than those that explore the space of actions. We dispel such beliefs by introducing a random search method for training static, linear policies for continuous control problems, matching state-of-the-art sample efficiency on the benchmark MuJoCo locomotion tasks. Our method also finds a nearly optimal controller for a challenging instance of the Linear Quadratic Regulator, a classical problem in control theory, when the dynamics are not known. Computationally, our random search algorithm is at least 15 times more efficient than the fastest competing model-free methods on these benchmarks. We take advantage of this computational efficiency to evaluate the performance of our method over hundreds of random seeds and many different hyperparameter configurations for each benchmark task. Our simulations highlight a high variability in performance in these benchmark tasks, suggesting that commonly used estimations of sample efficiency do not adequately evaluate the performance of RL algorithms.

This research enhances linear regression models by integrating a Kalman filter and analysing curve areas to minimize loss. The goal is to develop an optimal linear regression equation using stochastic gradient descent (SGD) for weight updating. Our approach involves a stepwise process, starting with user-defined parameters. The linear regression model is trained using SGD, tracking weights and loss separately and zipping them finally. A Kalman filter is then trained based on weight and loss arrays to predict the next consolidated weights. Predictions result from multiplying input averages with weights, evaluated for loss to form a weight-versus-loss curve. The curve's equation is derived using the two-point formula, and area under the curve is calculated via integration. The linear regression equation with minimum area becomes the optimal curve for prediction. Benefits include avoiding constant weight updates via gradient descent and working with partial datasets, unlike methods needing the entire set. However, computational complexity should be considered. The Kalman filter's accuracy might diminish beyond a certain prediction range.

Contact-rich manipulation tasks with stiff frictional elements like connector insertion are difficult to model with rigid-body simulators. In this work, we propose a new approach for modeling these environments by learning a quasi-static contact force model instead of a full simulator. Using a feature vector that contains information about the configuration and control, we find a linear mapping adequately captures the relationship between this feature vector and the sensed contact forces. A novel Linear Model Learning (LML) algorithm is used to solve for the globally optimal mapping in real time without any matrix inversions, resulting in an algorithm that runs in nearly constant time on a GPU as the model size increases. We validate the proposed approach for connector insertion both in simulation and hardware experiments, where the learned model is combined with an optimization-based controller to achieve smooth insertions in the presence of misalignments and uncertainty. Our website featuring videos, code, and more materials is available at https://model-based-plugging.github.io/.

Tracking by detection has been the prevailing paradigm in the field of Multi-object Tracking (MOT). These methods typically rely on the Kalman Filter to estimate the future locations of objects, assuming linear object motion. However, they fall short when tracking objects exhibiting nonlinear and diverse motion in scenarios like dancing and sports. In addition, there has been limited focus on utilizing learning-based motion predictors in MOT. To address these challenges, we resort to exploring data-driven motion prediction methods. Inspired by the great expectation of state space models (SSMs), such as Mamba, in long-term sequence modeling with near-linear complexity, we introduce a Mamba-based motion model named Mamba moTion Predictor (MTP). MTP is designed to model the complex motion patterns of objects like dancers and athletes. Specifically, MTP takes the spatial-temporal location dynamics of objects as input, captures the motion pattern using a bi-Mamba encoding layer, and predicts the next motion. In real-world scenarios, objects may be missed due to occlusion or motion blur, leading to premature termination of their trajectories. To tackle this challenge, we further expand the application of MTP. We employ it in an autoregressive way to compensate for missing observations by utilizing its own predictions as inputs, thereby contributing to more consistent trajectories. Our proposed tracker, MambaTrack, demonstrates advanced performance on benchmarks such as Dancetrack and SportsMOT, which are characterized by complex motion and severe occlusion.

Unknown dynamic load carrying is one important practical application for quadruped robots. Such a problem is non-trivial, posing three major challenges in quadruped locomotion control. First, how to model or represent the dynamics of the load in a generic manner. Second, how to make the robot capture the dynamics without any external sensing. Third, how to enable the robot to interact with load handling the mutual effect and stabilizing the load. In this work, we propose a general load modeling approach called load characteristics modeling to capture the dynamics of the load. We integrate this proposed modeling technique and leverage recent advances in Reinforcement Learning (RL) based locomotion control to enable the robot to infer the dynamics of load movement and interact with the load indirectly to stabilize it and realize the sim-to-real deployment to verify its effectiveness in real scenarios. We conduct extensive comparative simulation experiments to validate the effectiveness and superiority of our proposed method. Results show that our method outperforms other methods in sudden load resistance, load stabilizing and locomotion with heavy load on rough terrain. https://leixinjonaschang.github.io/leggedloadadapt.github.io/{Project Page}.

We propose iterative inversion -- an algorithm for learning an inverse function without input-output pairs, but only with samples from the desired output distribution and access to the forward function. The key challenge is a distribution shift between the desired outputs and the outputs of an initial random guess, and we prove that iterative inversion can steer the learning correctly, under rather strict conditions on the function. We apply iterative inversion to learn control. Our input is a set of demonstrations of desired behavior, given as video embeddings of trajectories (without actions), and our method iteratively learns to imitate trajectories generated by the current policy, perturbed by random exploration noise. Our approach does not require rewards, and only employs supervised learning, which can be easily scaled to use state-of-the-art trajectory embedding techniques and policy representations. Indeed, with a VQ-VAE embedding, and a transformer-based policy, we demonstrate non-trivial continuous control on several tasks. Further, we report an improved performance on imitating diverse behaviors compared to reward based methods.

This paper studies attack detection for discrete-time linear systems with stochastic process noise that produce both a vulnerable (i.e., attackable) linear measurement and a secured (i.e., unattackable) quadratic measurement. The motivating application of this model is a dynamic-game setting where the quadratic measurement is interpreted as a system-level utility or reward, and control inputs into the linear system are interpreted as control policies that, once applied, are known to all game participants and which steer the system towards a game-theoretic equilibrium (e.g., Nash equilibrium). To detect attacks on the linear channel, we develop a novel quadratic-utility-aware observer that leverages the secured quadratic output and enforces measurement consistency via a projection step. We establish three properties for this observer: feasibility of the true state, prox-regularity of the quadratic-constraint set, and a monotone error-reduction guarantee in the noise-free case. To detect adversarial manipulation, we compare linear and quadratic observer trajectories using a wild bootstrap maximum mean discrepancy (MMD) test that provides valid inference under temporal dependence. We validate our framework using numerical experiments of a pursuit-evasion game, where the quadratic observer preserves estimation accuracy under linear-sensor attacks, while the statistical test detects distributional divergence between the observers' trajectories.

Reinforcement learning provides a framework for learning control policies that can reproduce diverse motions for simulated characters. However, such policies often exploit unnatural high-frequency signals that are unachievable by humans or physical robots, making them poor representations of real-world behaviors. Existing work addresses this issue by adding a reward term that penalizes a large change in actions over time. This term often requires substantial tuning efforts. We propose to use the action Jacobian penalty, which penalizes changes in action with respect to the changes in simulated state directly through auto differentiation. This effectively eliminates unrealistic high-frequency control signals without task specific tuning. While effective, the action Jacobian penalty introduces significant computational overhead when used with traditional fully connected neural network architectures. To mitigate this, we introduce a new architecture called a Linear Policy Net (LPN) that significantly reduces the computational burden for calculating the action Jacobian penalty during training. In addition, a LPN requires no parameter tuning, exhibits faster learning convergence compared to baseline methods, and can be more efficiently queried during inference time compared to a fully connected neural network. We demonstrate that a Linear Policy Net, combined with the action Jacobian penalty, is able to learn policies that generate smooth signals while solving a number of motion imitation tasks with different characteristics, including dynamic motions such as a backflip and various challenging parkour skills. Finally, we apply this approach to create policies for dynamic motions on a physical quadrupedal robot equipped with an arm.

In distributed model predictive control for multi-drone collision avoidance, a fixed prediction horizon forces a compromise: a short horizon is inexpensive but reacts late to approaching neighbors, whereas a long one anticipates conflicts at a per-step cost that grows superlinearly with its length. We propose a conflict-predictive variable horizon that each drone sets locally, leaving the distributed model predictive control itself unchanged. From a short history of observed positions, a drone extrapolates the flight lines of its neighbors, tests each against its own using confidence funnels that narrow with prediction range, and obtains each time to conflict in closed form. The horizon is then the smallest admissible value whose planning window covers the farthest predicted conflict. It collapses to its minimum in clear airspace and grows only when a conflict lies ahead. Provided this minimum meets a single computable feasibility bound, we prove that recursive feasibility and asymptotic stability are preserved for every horizon the policy can select. These guarantees hold for a linear model, and a cascaded inner loop reduces each quadrotor's translational dynamics to a perturbed double integrator, so they carry over to the linearized quadrotor model and, as practical stability, to the full nonlinear one. In simulation on dense antipodal-swap benchmarks, the variable horizon reduces both per-step solver cost and total computation well below those of a long fixed horizon, and it maintains separation in every run, which a short fixed horizon of comparable per-step cost does not.

We provide an algorithm for adaptive legged locomotion via online learning and model predictive control. The algorithm is composed of two interacting modules: model predictive control (MPC) and online learning of residual dynamics. The residual dynamics can represent modeling errors and external disturbances. We are motivated by the future of autonomy where quadrupeds will autonomously perform complex tasks despite real-world unknown uncertainty, such as unknown payload and uneven terrains. The algorithm uses random Fourier features to approximate the residual dynamics in reproducing kernel Hilbert spaces. Then, it employs MPC based on the current learned model of the residual dynamics. The model is updated online in a self-supervised manner using least squares based on the data collected while controlling the quadruped. The algorithm enjoys sublinear dynamic regret, defined as the suboptimality against an optimal clairvoyant controller that knows how the residual dynamics. We validate our algorithm in Gazebo and MuJoCo simulations, where the quadruped aims to track reference trajectories. The Gazebo simulations include constant unknown external forces up to 12g, where g is the gravity vector, in flat terrain, slope terrain with 20degree inclination, and rough terrain with 0.25m height variation. The MuJoCo simulations include time-varying unknown disturbances with payload up to 8~kg and time-varying ground friction coefficients in flat terrain.

In legged locomotion, divergent components of motion (DCMs) have emerged as characteristic states for balance control. They isolate the unstable mode of the dynamics but, in existing formulations, apply only to reduced models such as the linear inverted pendulum. In this study, we show how DCMs can be more generally formulated as Koopman eigenfunctions. Whereas Koopman analysis typically targets eigenvalues near zero, which capture conserved or slowly varying quantities, our investigation leads us to deliberately search for unstable eigenpairs with large eigenvalues. The resulting Koopman DCMs are data-driven observables trained using only real-robot data. On a real biped, DCMs learned from one hour of robot data improve tracking of reference walking patterns. We further show how learned DCMs provide state-based viability constraints when combined with model predictive control.

This article presents an in-depth review of the topic of path following for autonomous robotic vehicles, with a specific focus on vehicle motion in two dimensional space (2D). From a control system standpoint, path following can be formulated as the problem of stabilizing a path following error system that describes the dynamics of position and possibly orientation errors of a vehicle with respect to a path, with the errors defined in an appropriate reference frame. In spite of the large variety of path following methods described in the literature we show that, in principle, most of them can be categorized in two groups: stabilization of the path following error system expressed either in the vehicle's body frame or in a frame attached to a "reference point" moving along the path, such as a Frenet-Serret (F-S) frame or a Parallel Transport (P-T) frame. With this observation, we provide a unified formulation that is simple but general enough to cover many methods available in the literature. We then discuss the advantages and disadvantages of each method, comparing them from the design and implementation standpoint. We further show experimental results of the path following methods obtained from field trials testing with under-actuated and fully-actuated autonomous marine vehicles. In addition, we introduce open-source Matlab and Gazebo/ROS simulation toolboxes that are helpful in testing path following methods prior to their integration in the combined guidance, navigation, and control systems of autonomous vehicles.

Accurate grasp force control is one of the key skills for ensuring successful and damage-free robotic grasping of objects. Although existing methods have conducted in-depth research on slip detection and grasping force planning, they often overlook the issue of adaptive tracking of the actual force to the target force when handling objects with different material properties. The optimal parameters of a force tracking controller are significantly influenced by the object's stiffness, and many adaptive force tracking algorithms rely on stiffness estimation. However, real-world objects often exhibit viscous, plastic, or other more complex nonlinear time-varying behaviors, and existing studies provide insufficient support for these materials in terms of stiffness definition and estimation. To address this, this paper introduces the concept of generalized stiffness, extending the definition of stiffness to nonlinear time-varying grasp system models, and proposes an online generalized stiffness estimator based on Long Short-Term Memory (LSTM) networks. Based on generalized stiffness, this paper proposes an adaptive parameter adjustment strategy using a PI controller as an example, enabling dynamic force tracking for objects with varying characteristics. Experimental results demonstrate that the proposed method achieves high precision and short probing time, while showing better adaptability to non-ideal objects compared to existing methods. The method effectively solves the problem of grasp force tracking in unknown, nonlinear, and time-varying grasp systems, demonstrating the generalization capability of our neural network and enhancing the robotic grasping ability in unstructured environments.

Learning whole-body control for locomotion and arm motions in a single policy has challenges, as the two tasks have conflicting goals. For instance, efficient locomotion typically favors a horizontal base orientation, while end-effector tracking may benefit from base tilting to extend reachability. Additionally, current Reinforcement Learning (RL) approaches using a pose-based task specification lack the ability to directly control the end-effector velocity, making smoothly executing trajectories very challenging. To address these limitations, we propose an RL-based framework that allows for dynamic, velocity-aware whole-body end-effector control. Our method introduces a multi-critic actor architecture that decouples the reward signals for locomotion and manipulation, simplifying reward tuning and allowing the policy to resolve task conflicts more effectively. Furthermore, we design a twist-based end-effector task formulation that can track both discrete poses and motion trajectories. We validate our approach through a set of simulation and hardware experiments using a quadruped robot equipped with a robotic arm. The resulting controller can simultaneously walk and move its end-effector and shows emergent whole-body behaviors, where the base assists the arm in extending the workspace, despite a lack of explicit formulations.

Sampling-based kinodynamic planners, such as Rapidly-exploring Random Trees (RRTs), pose two fundamental challenges: computing a reliable (pseudo-)metric for the distance between two randomly sampled nodes, and computing a steering input to connect the nodes. The core of these challenges is a Two Point Boundary Value Problem, which is known to be NP-hard. Recently, the distance metric has been approximated using supervised learning, reducing computation time drastically. The previous work on such learning RRTs use direct optimal control to generate the data for supervised learning. This paper proposes to use indirect optimal control instead, because it provides two benefits: it reduces the computational effort to generate the data, and it provides a low dimensional parametrization of the action space. The latter allows us to learn both the distance metric and the steering input to connect two nodes. This eliminates the need for a local planner in learning RRTs. Experimental results on a pendulum swing up show 10-fold speed-up in both the offline data generation and the online planning time, leading to at least a 10-fold speed-up in the overall planning time.

We present a Learning from Demonstration method for teaching robots to perform search strategies imitated from humans in scenarios where alignment tasks fail due to position uncertainty. The method utilizes human demonstrations to learn both a state invariant dynamics model and an exploration distribution that captures the search area covered by the demonstrator. We present two alternative algorithms for computing a search trajectory from the exploration distribution, one based on sampling and another based on deterministic ergodic control. We augment the search trajectory with forces learnt through the dynamics model to enable searching both in force and position domains. An impedance controller with superposed forces is used for reproducing the learnt strategy. We experimentally evaluate the method on a KUKA LWR4+ performing a 2D peg-in-hole and a 3D electricity socket task. Results show that the proposed method can, with only few human demonstrations, learn to complete the search task.

World Action Models (WAMs) enable semantically- and physically-informed control but are brittle under distribution shift. In this work, we use mechanistic interpretability to study how robustness-relevant perturbations are represented in WAM activation space. Comparing activations across successful and unsuccessful rollouts, we find some WAM architectures exhibit low-dimensional linear separability for robustness-critical features, while others do not. This motivates the use of contrastive activation directions for training-free WAM steering. We also show that local linearity in WAM activation dynamics enables efficient feedback steering via model-based optimal control, yielding World-Action Linear Quadratic Regulator (WA-LQR), a minimally-invasive reduced-order LQR controller. Via mechanistic evaluations, we predict strong steerability in the Cosmos-Policy and DiT4DiT models but weak steerability in LingBot-VA, consistent with steering intervention results. On Cosmos-Policy and DiT4DiT, WA-LQR generalizes contrastive directions to new tasks and improves robustness to camera, gripper, and visual-noise perturbations over unsteered and prompt steering baselines.

Since batch algorithms suffer from lack of proficiency in confronting model mismatches and disturbances, this contribution proposes an adaptive scheme based on continuous Lyapunov function for online robot dynamic identification. This paper suggests stable updating rules to drive neural networks inspiring from model reference adaptive paradigm. Network structure consists of three parallel self-driving neural networks which aim to estimate robot dynamic terms individually. Lyapunov candidate is selected to construct energy surface for a convex optimization framework. Learning rules are driven directly from Lyapunov functions to make the derivative negative. Finally, experimental results on 3-DOF Phantom Omni Haptic device demonstrate efficiency of the proposed method.

Large-scale humanoid motion-tracking controllers are commonly improved by reallocating training effort: difficult motions are sampled more often, isolated into smaller subsets, or assigned to specialized experts. We show that this view is incomplete. In strong whole-body-control baselines, a residual set of feasible training clips remains unsolved even under targeted training, especially for high-dynamic transitions and balance-critical motions. These failures arise not only from insufficient exposure, but from a mismatch between the motion demands and the effective capability induced by the default training recipe. We propose Athena-WBC, a compact teacher-student pipeline with capability-aligned policy experts for long-tail humanoid whole-body control. Dynamic experts use a tracking-focused, constraint-aware objective that removes conservative effort and temporal-control penalties while preserving physical feasibility constraints; balance experts use a gravity curriculum to improve early-training survivability. The resulting privileged teachers are motion-routed for DAgger distillation and then compressed into a single controller with deployable observations followed by RL fine-tuning. Experiments on a full-size humanoid show improved recovery of training-set long-tail motions and better held-out tracking than a strong SONIC-recipe baseline, using only a small number of experts.

In many real-world sequential decision-making problems, an action does not immediately reflect on the feedback and spreads its effects over a long time frame. For instance, in online advertising, investing in a platform produces an instantaneous increase of awareness, but the actual reward, i.e., a conversion, might occur far in the future. Furthermore, whether a conversion takes place depends on: how fast the awareness grows, its vanishing effects, and the synergy or interference with other advertising platforms. Previous work has investigated the Multi-Armed Bandit framework with the possibility of delayed and aggregated feedback, without a particular structure on how an action propagates in the future, disregarding possible dynamical effects. In this paper, we introduce a novel setting, the Dynamical Linear Bandits (DLB), an extension of the linear bandits characterized by a hidden state. When an action is performed, the learner observes a noisy reward whose mean is a linear function of the hidden state and of the action. Then, the hidden state evolves according to linear dynamics, affected by the performed action too. We start by introducing the setting, discussing the notion of optimal policy, and deriving an expected regret lower bound. Then, we provide an optimistic regret minimization algorithm, Dynamical Linear Upper Confidence Bound (DynLin-UCB), that suffers an expected regret of order mathcal{O} Big( d sqrt{T}{(1-rho)^{3/2}} Big), where rho is a measure of the stability of the system, and d is the dimension of the action vector. Finally, we conduct a numerical validation on a synthetic environment and on real-world data to show the effectiveness of DynLin-UCB in comparison with several baselines.

The massive overactuation in the human musculoskeletal system makes it challenging to train musculoskeletal models to generate human-like motion via reinforcement learning, primarily because exploration in the resulting high-dimensional and redundant action space is extremely inefficient. To address this problem, we propose the λ-hold controller, inspired by the equilibrium-point (EP) hypothesis, which has been widely supported by extensive evidence from human motor control studies. The policy's control variable is the per-muscle EP threshold length λ, from which a stretch-reflex recruitment law computes the muscle excitations automatically. Holding each λ over an interval of the gait phase also sharply reduces the frequency at which the policy must be queried. Consequently, the controller, to our knowledge for the first time, enables a muscle-actuated skeletal model to learn human-like sprinting using only a minimal reward within an hour of training. The efficient exploration through the proposed λ-hold controller is not merely an engineering trick but an approach grounded in physiology, bringing together the EP hypothesis, intermittent control, and optimal feedback control. Beyond encapsulating human-like behavior in predictive simulation, this achievement contributes to developing a learnable model of the human motor controller.

This paper proposes a novel data-driven approach for inertial navigation, which learns to estimate trajectories of natural human motions just from an inertial measurement unit (IMU) in every smartphone. The key observation is that human motions are repetitive and consist of a few major modes (e.g., standing, walking, or turning). Our algorithm regresses a velocity vector from the history of linear accelerations and angular velocities, then corrects low-frequency bias in the linear accelerations, which are integrated twice to estimate positions. We have acquired training data with ground-truth motions across multiple human subjects and multiple phone placements (e.g., in a bag or a hand). The qualitatively and quantitatively evaluations have demonstrated that our algorithm has surprisingly shown comparable results to full Visual Inertial navigation. To our knowledge, this paper is the first to integrate sophisticated machine learning techniques with inertial navigation, potentially opening up a new line of research in the domain of data-driven inertial navigation. We will publicly share our code and data to facilitate further research.

Robust navigation in cluttered environments remains a fundamental challenge for quadrotors, particularly when strong wind disturbances arise, which perturb vehicle dynamics, limit control authority, and substantially increase collision risk. Existing learning-based navigation policies typically rely on obstacle perception and proprioceptive observations, requiring the policy to infer time-varying disturbance effects implicitly and thereby limiting robustness under partial observability. This paper proposes WAND (Wind-Aware Navigation with Disturbance Estimation), a reinforcement learning framework for navigation under time-varying wind disturbances in dense obstacle fields. Specifically, WAND estimates wind-induced disturbance acceleration from historical proprioceptive states using a Temporal Convolutional Network (TCN). This estimation is integrated into the policy via a zero-initialized residual module, WindAdapter, while simultaneously providing feedforward compensation for low-level control. The dual use of the estimate couples disturbance-conditioned navigation with feedforward disturbance rejection. Across 12 wind-disturbed simulation settings, WAND improved the observed success rate by 8.3 percentage points on average relative to feedforward compensation alone. Controlled opposite-crosswind experiments further showed wind-direction-dependent trajectory adaptation. In indoor fan-induced flight tests, WAND succeeded in 18 of 20 trials, demonstrating the feasibility of real-time onboard navigation.

We argue that high-quality motion data can steer tracking policies toward better optimization trajectories early in training. In this work, we introduce LIMMT (Less Is More for Motion Tracking). To our knowledge, this is the first data-centric study for physics-based humanoid motion tracking. We go beyond simply removing low-quality and erroneous clips, but define motion data quality through three dimensions: physics feasibility, diversity, and complexity. We show that even training with under 3% of AMASS yields better tracking performance than training with the full dataset. We further conduct data cleaning on the estimated web-sourced mocap data. Extensive experiments and analyses validate the effectiveness of our framework.

Replicating the remarkable athleticism seen in animals has long been a challenge in robotics control. Although Reinforcement Learning (RL) has demonstrated significant progress in dynamic legged locomotion control, the substantial sim-to-real gap often hinders the real-world demonstration of truly dynamic movements. We propose a new framework to mitigate this gap through frequency-domain analysis-based impedance matching between simulated and real robots. Our framework offers a structured guideline for parameter selection and the range for dynamics randomization in simulation, thus facilitating a safe sim-to-real transfer. The learned policy using our framework enabled jumps across distances of 55 cm and heights of 38 cm. The results are, to the best of our knowledge, one of the highest and longest running jumps demonstrated by an RL-based control policy in a real quadruped robot. Note that the achieved jumping height is approximately 85% of that obtained from a state-of-the-art trajectory optimization method, which can be seen as the physical limit for the given robot hardware. In addition, our control policy accomplished stable walking at speeds up to 2 m/s in the forward and backward directions, and 1 m/s in the sideway direction.

We propose a training recipe that treats charged-particle trajectory parameter regression on high-energy physics detector data as a sequence-modeling task. Kalman filters and linearized least-squares fits have been the classical standard approach for this task: they are optimal estimators for sparsely sampled linear-Gaussian data and are commonly used for trajectory parameter regression (fitting). The classical fitting techniques implemented for this domain reach a final precision of one part in 10^5 through detailed modeling of detector geometry, material, detection effects and precise numerical integration of the equations of motion through the detector's inhomogeneous magnetic field. With this study, we demonstrate that using a bidirectional gated linear recurrent encoder, one is able to reproduce the full precision of classical track fitting techniques. Using a custom kernel, we also achieve significantly higher throughput during GPU inference, compared to classical fitting software running on similarly priced multi-core CPU servers representing typically employed hardware. Such a speedup would lead to considerable cost savings for the pattern recognition at the Large Hadron Collider. To our knowledge, this is the first end-to-end learned track fit to reach the full precision and, at the same time, offer the opportunity to reduce the computing costs.

Ropes, cables, and other deformable linear objects appear in tasks from untangling to cable routing and suturing, yet controlling their shape remains a challenge in robot manipulation. We study model-based shape control in a general setting: the object lies unfixated on a support surface and two arms may grasp and move it anywhere along its length. Because each arm chooses a grasp point, direction, and magnitude, the joint action space is combinatorially large, and the dynamics model's per-prediction cost bounds how much of it a planner can search. We present ForwardDLO, a recurrent latent dynamics model for this unfixated bimanual setting that predicts per-segment displacements grounded in the observed rope state at every step. Our model reaches accuracy comparable to more expensive baselines while containing no explicit segment-to-segment operations, which makes batched evaluation of candidate actions cheap. On open-loop prediction of real rope motion it reaches the lowest error of the learned models we evaluate, 13% below the strongest baseline. Within a fixed time budget it scores 8 to 22 times more candidate actions than models of comparable accuracy while matching them in real-world shape matching; and on a simulated routing task at a 30Hz control rate, this throughput converts into 98% task success versus at most 30% for the baselines at their own budgets. We release the model, code, and a dataset of 2.42 million simulated and 14,107 real rope transitions at https://anonymous.4open.science/r/ForwardDLO/

Unmodeled aerodynamic disturbances pose a key challenge for multirotor flight when multiple vehicles are in close proximity to each other. However, certain missions require two multirotors to approach each other within 1-2 body-lengths of each other and hold formation -- we consider one such practical instance: vertically docking two multirotors in the air. In this leader-follower setting, the follower experiences significant downwash interference from the leader in its final docking stages. To compensate for this, we employ a learnt downwash model online within an optimal feedback controller to accurately track a docking maneuver and then hold formation. Through real-world flights with different maneuvers, we demonstrate that this compensation is crucial for reducing the large vertical separation otherwise required by conventional/naive approaches. Our evaluations show a tracking error of less than 0.06m for the follower (a 3-4x reduction) when approaching vertically within two body-lengths of the leader. Finally, we deploy the complete system to effect a successful physical docking between two airborne multirotors in a single smooth planned trajectory.

Achieving general-purpose humanoid control requires a delicate balance between the precise execution of commanded motions and the flexible, anthropomorphic adaptability needed to recover from unpredictable environmental perturbations. Current general controllers predominantly formulate motion control as a rigid reference-tracking problem. While effective in nominal conditions, these trackers often exhibit brittle, non-anthropomorphic failure modes under severe disturbances, lacking the generative adaptability inherent to human motor control. To overcome this limitation, we propose Heracles, a novel state-conditioned diffusion middleware that bridges precise motion tracking and generative synthesis. Rather than relying on rigid tracking paradigms or complex explicit mode-switching, Heracles operates as an intermediary layer between high-level reference motions and low-level physics trackers. By conditioning on the robot's real-time state, the diffusion model implicitly adapts its behavior: it approximates an identity map when the state closely aligns with the reference, preserving zero-shot tracking fidelity. Conversely, when encountering significant state deviations, it seamlessly transitions into a generative synthesizer to produce natural, anthropomorphic recovery trajectories. Our framework demonstrates that integrating generative priors into the control loop not only significantly enhances robustness against extreme perturbations but also elevates humanoid control from a rigid tracking paradigm to an open-ended, generative general-purpose architecture.

We present formulation and open-source tools to achieve in-material model predictive control of sensor/actuator systems using learned forward kinematics and on-device computation. Microcontroller units (MCUs) that compute the prediction and control task while colocated with the sensors and actuators enable in-material untethered behaviors. In this approach, small parameter size neural network models learn forward kinematics offline. Our open-source compiler, nn4mc, generates code to offload these predictions onto MCUs. A Newton-Raphson solver then computes the control input in real time. We first benchmark this nonlinear control approach against a PID controller on a mass-spring-damper simulation. We then study experimental results on two experimental rigs with different sensing, actuation and computational hardware: a tendon-based platform with embedded LightLace sensors and a HASEL-based platform with magnetic sensors. Experimental results indicate effective high-bandwidth tracking of reference paths (greater than or equal to 120 Hz) with a small memory footprint (less than or equal to 6.4% of flash memory). The measured path following error does not exceed 2mm in the tendon-based platform. The simulated path following error does not exceed 1mm in the HASEL-based platform. The mean power consumption of this approach in an ARM Cortex-M4f device is 45.4 mW. This control approach is also compatible with Tensorflow Lite models and equivalent on-device code. In-material intelligence enables a new class of composites that infuse autonomy into structures and systems with refined artificial proprioception.

Robotic systems often exhibit unstable modes, along which small perturbations and disturbances can cause unbounded growth unless corrected through feedback. Controlling such systems from high-dimensional visual observations requires representations that preserve these modes. Joint-embedding predictive architectures (JEPAs) provide a natural framework for learning such representations and their dynamics from visual data. However, we demonstrate that next step prediction combined with anti-collapse regularization does not guarantee that controllable unstable modes are preserved: the training loss can be minimized while these modes are collapsed, making stabilization from the learned representation impossible. To address this, we augment world-model training with an action reconstruction objective (i.e., an inverse dynamics loss) that encourages control-aware representations, namely, visual representations that preserve crucial features for control. We prove that exact action reconstruction makes the encoder injective on the finite-horizon reachable subspace. Thus, the encoder cannot discard any state direction reachable by an action sequence within H steps. Moreover, we show that, as H grows, the dominant eigenspace of the finite-horizon controllability Gramian converges to the controllable unstable subspace. We establish our theoretical results for linear systems and demonstrate empirically that our findings extend to nonlinear visual control tasks (CartPole, Walker2D, and PointMaze), highlighting the benefits of control-aware representation learning.

This paper presents the first decentralized method to enable real-world 6-DoF manipulation of a cable-suspended load using a team of Micro-Aerial Vehicles (MAVs). Our method leverages multi-agent reinforcement learning (MARL) to train an outer-loop control policy for each MAV. Unlike state-of-the-art controllers that utilize a centralized scheme, our policy does not require global states, inter-MAV communications, nor neighboring MAV information. Instead, agents communicate implicitly through load pose observations alone, which enables high scalability and flexibility. It also significantly reduces computing costs during inference time, enabling onboard deployment of the policy. In addition, we introduce a new action space design for the MAVs using linear acceleration and body rates. This choice, combined with a robust low-level controller, enables reliable sim-to-real transfer despite significant uncertainties caused by cable tension during dynamic 3D motion. We validate our method in various real-world experiments, including full-pose control under load model uncertainties, showing setpoint tracking performance comparable to the state-of-the-art centralized method. We also demonstrate cooperation amongst agents with heterogeneous control policies, and robustness to the complete in-flight loss of one MAV. Videos of experiments: https://autonomousrobots.nl/paper_websites/aerial-manipulation-marl

For robots to be useful outside labs and specialized factories we need a way to teach them new useful behaviors quickly. Current approaches lack either the generality to onboard new tasks without task-specific engineering, or else lack the data-efficiency to do so in an amount of time that enables practical use. In this work we explore dense tracking as a representational vehicle to allow faster and more general learning from demonstration. Our approach utilizes Track-Any-Point (TAP) models to isolate the relevant motion in a demonstration, and parameterize a low-level controller to reproduce this motion across changes in the scene configuration. We show this results in robust robot policies that can solve complex object-arrangement tasks such as shape-matching, stacking, and even full path-following tasks such as applying glue and sticking objects together, all from demonstrations that can be collected in minutes.

We address the problem of model-free distributed stabilization of heterogeneous multi-agent systems using reinforcement learning (RL). Two algorithms are developed. The first algorithm solves a centralized linear quadratic regulator (LQR) problem without knowing any initial stabilizing gain in advance. The second algorithm builds upon the results of the first algorithm, and extends it to distributed stabilization of multi-agent systems with predefined interaction graphs. Rigorous proofs are provided to show that the proposed algorithms achieve guaranteed convergence if specific conditions hold. A simulation example is presented to demonstrate the theoretical results.

Operating robots precisely and at high speeds has been a long-standing goal of robotics research. Balancing these competing demands is key to enabling the seamless collaboration of robots and humans and increasing task performance. However, traditional motor-driven systems often fall short in this balancing act. Due to their rigid and often heavy design exacerbated by positioning the motors into the joints, faster motions of such robots transfer high forces at impact. To enable precise and safe dynamic motions, we introduce a four degree-of-freedom~(DoF) tendon-driven robot arm. Tendons allow placing the actuation at the base to reduce the robot's inertia, which we show significantly reduces peak collision forces compared to conventional robots with motors placed near the joints. Pairing our robot with pneumatic muscles allows generating high forces and highly accelerated motions, while benefiting from impact resilience through passive compliance. Since tendons are subject to additional friction and hence prone to wear and tear, we validate the reliability of our robotic arm on various experiments, including long-term dynamic motions. We also demonstrate its ease of control by quantifying the nonlinearities of the system and the performance on a challenging dynamic table tennis task learned from scratch using reinforcement learning. We open-source the entire hardware design, which can be largely 3D printed, the control software, and a proprioceptive dataset of 25 days of diverse robot motions at webdav.tuebingen.mpg.de/pamy2.

A new generalized matrix inverse is derived which is consistent with respect to arbitrary nonsingular diagonal transformations, e.g., it preserves units associated with variables under state space transformations, thus providing a general solution to a longstanding open problem relevant to a wide variety of applications in robotics, tracking, and control systems. The new inverse complements the Drazin inverse (which is consistent with respect to similarity transformations) and the Moore-Penrose inverse (which is consistent with respect to unitary/orthonormal transformations) to complete a trilogy of generalized matrix inverses that exhausts the standard family of analytically-important linear system transformations. Results are generalized to obtain unit-consistent and unit-invariant matrix decompositions and examples of their use are described.

Visual object tracking is essential to intelligent robots. Most existing approaches have ignored the online latency that can cause severe performance degradation during real-world processing. Especially for unmanned aerial vehicles (UAVs), where robust tracking is more challenging and onboard computation is limited, the latency issue can be fatal. In this work, we present a simple framework for end-to-end latency-aware tracking, i.e., end-to-end predictive visual tracking (PVT++). Unlike existing solutions that naively append Kalman Filters after trackers, PVT++ can be jointly optimized, so that it takes not only motion information but can also leverage the rich visual knowledge in most pre-trained tracker models for robust prediction. Besides, to bridge the training-evaluation domain gap, we propose a relative motion factor, empowering PVT++ to generalize to the challenging and complex UAV tracking scenes. These careful designs have made the small-capacity lightweight PVT++ a widely effective solution. Additionally, this work presents an extended latency-aware evaluation benchmark for assessing an any-speed tracker in the online setting. Empirical results on a robotic platform from the aerial perspective show that PVT++ can achieve significant performance gain on various trackers and exhibit higher accuracy than prior solutions, largely mitigating the degradation brought by latency.

The goal of reinforcement learning (RL) is to find a policy that maximizes the expected cumulative return. It has been shown that this objective can be represented as an optimization problem of state-action visitation distribution under linear constraints. The dual problem of this formulation, which we refer to as dual RL, is unconstrained and easier to optimize. In this work, we first cast several state-of-the-art offline RL and offline imitation learning (IL) algorithms as instances of dual RL approaches with shared structures. Such unification allows us to identify the root cause of the shortcomings of prior methods. For offline IL, our analysis shows that prior methods are based on a restrictive coverage assumption that greatly limits their performance in practice. To fix this limitation, we propose a new discriminator-free method ReCOIL that learns to imitate from arbitrary off-policy data to obtain near-expert performance. For offline RL, our analysis frames a recent offline RL method XQL in the dual framework, and we further propose a new method f-DVL that provides alternative choices to the Gumbel regression loss that fixes the known training instability issue of XQL. The performance improvements by both of our proposed methods, ReCOIL and f-DVL, in IL and RL are validated on an extensive suite of simulated robot locomotion and manipulation tasks. Project code and details can be found at this https://hari-sikchi.github.io/dual-rl.

Controlling a robot based on physics-consistent dynamic models, such as Deep Lagrangian Networks (DeLaN), can improve the generalizability and interpretability of the resulting behavior. However, in complex environments, the number of objects to potentially interact with is vast, and their physical properties are often uncertain. This complexity makes it infeasible to employ a single global model. Therefore, we need to resort to online system identification of context-aware models that capture only the currently relevant aspects of the environment. While physical principles such as the conservation of energy may not hold across varying contexts, ensuring physical plausibility for any individual context-aware model can still be highly desirable, particularly when using it for receding horizon control methods such as model predictive control (MPC). Hence, in this work, we extend DeLaN to make it context-aware, combine it with a recurrent network for online system identification, and integrate it with an MPC for adaptive, physics-consistent control. We also combine DeLaN with a residual dynamics model to leverage the fact that a nominal model of the robot is typically available. We evaluate our method on a 7-DOF robot arm for trajectory tracking under varying loads. Our method reduces the end-effector tracking error by 39%, compared to a 21% improvement achieved by a baseline that uses an extended Kalman filter.

Feedforward steering control is a key component of hierarchical control architectures for autonomous racing. The goal is to reduce steering corrections from the feedback controllers by predicting the vehicle's inverse lateral dynamics. This paper presents a systematic benchmark of two learning-based and two empirical (analytical) feedforward steering controllers. We introduce a new ehd formulation based on a polynomial surface fit that captures velocity-dependent nonlinear steering behavior with minimal parametrization. We test the feedforward controllers in a high-fidelity simulation framework based on the real-world Abu Dhabi Autonomous Racing League competition, using a high-fidelity double-track vehicle dynamics simulator. Open-loop evaluation shows that the learning-based controllers achieve the lowest prediction errors; however, closed-loop testing reveals that this improved accuracy does not translate into superior path tracking performance or lap times, even after iterative fine-tuning. In contrast, the proposed EHD approach achieves the best overall closed-loop robustness and lap time, highlighting the necessity of evaluating feedforward strategies within the complete trajectory planning and control software stack. Our code is available at https://github.com/TUMRT/steering_ff_control.

Learning versatile whole-body skills by tracking various human motions is a fundamental step toward general-purpose humanoid robots. This task is particularly challenging because a single policy must master a broad repertoire of motion skills while ensuring stability over long-horizon sequences. To this end, we present VMS, a unified whole-body controller that enables humanoid robots to learn diverse and dynamic behaviors within a single policy. Our framework integrates a hybrid tracking objective that balances local motion fidelity with global trajectory consistency, and an Orthogonal Mixture-of-Experts (OMoE) architecture that encourages skill specialization while enhancing generalization across motions. A segment-level tracking reward is further introduced to relax rigid step-wise matching, enhancing robustness when handling global displacements and transient inaccuracies. We validate VMS extensively in both simulation and real-world experiments, demonstrating accurate imitation of dynamic skills, stable performance over minute-long sequences, and strong generalization to unseen motions. These results highlight the potential of VMS as a scalable foundation for versatile humanoid whole-body control. The project page is available at https://kungfubot2-humanoid.github.io.

Loco-manipulation, physical interaction of various objects that is concurrently coordinated with locomotion, remains a major challenge for legged robots due to the need for both precise end-effector control and robustness to unmodeled dynamics. While model-based controllers provide precise planning via online optimization, they are limited by model inaccuracies. In contrast, learning-based methods offer robustness, but they struggle with precise modulation of interaction forces. We introduce RAMBO, a hybrid framework that integrates model-based whole-body control within a feedback policy trained with reinforcement learning. The model-based module generates feedforward torques by solving a quadratic program, while the policy provides feedback corrective terms to enhance robustness. We validate our framework on a quadruped robot across a diverse set of real-world loco-manipulation tasks, such as pushing a shopping cart, balancing a plate, and holding soft objects, in both quadrupedal and bipedal walking. Our experiments demonstrate that RAMBO enables precise manipulation capabilities while achieving robust and dynamic locomotion.

As humans move around, performing their daily tasks, they are able to recall where they have positioned objects in their environment, even if these objects are currently out of their sight. In this paper, we aim to mimic this spatial cognition ability. We thus formulate the task of Out of Sight, Not Out of Mind - 3D tracking active objects using observations captured through an egocentric camera. We introduce a simple but effective approach to address this challenging problem, called Lift, Match, and Keep (LMK). LMK lifts partial 2D observations to 3D world coordinates, matches them over time using visual appearance, 3D location and interactions to form object tracks, and keeps these object tracks even when they go out-of-view of the camera. We benchmark LMK on 100 long videos from EPIC-KITCHENS. Our results demonstrate that spatial cognition is critical for correctly locating objects over short and long time scales. E.g., for one long egocentric video, we estimate the 3D location of 50 active objects. After 120 seconds, 57% of the objects are correctly localised by LMK, compared to just 33% by a recent 3D method for egocentric videos and 17% by a general 2D tracking method.

Connected and automated vehicles demand lateral controllers that are simultaneously accurate, low-effort, and safe under model error and sensor noise. Modular controllers such as model predictive control (MPC) are interpretable and constraint-aware but rely on accurate models and hand-tuned weights. End-to-end learned policies, in particular continuous-action deep reinforcement learning, are adaptable and require no hand-designed control law, but offer no intrinsic safety guarantees and limited interpretability. This paper presents a hybrid architecture that combines an end-to-end Soft Actor-Critic (SAC) policy with a constrained linear MPC into a single steering command, using the MPC's first-step optimum as the model-based anchor and a single monotone blending coefficient that interpolates between the two paradigms. The architecture is evaluated on a linearized lateral bicycle model against a PID baseline, a tuned linear MPC, and a stand-alone SAC policy, across nominal, single-axis robustness, and multi-initial-condition ensemble experiments. The hybrid retains the tracking quality of stand-alone SAC while remaining inside the MPC's actuator envelope and preserving a deterministic, model-based contribution to every steering command. The architecture provides an actuator-envelope guarantee by construction but does not establish recursive feasibility or terminal invariance, and the closed-form blend does not prevent all corner-case divergences at the boundary of the training distribution. A corner-case analysis shows that the blend attenuates but cannot prevent failure under distribution shift, motivating a connectivity-aware extension in which the blending coefficient is scheduled by vehicle-to-everything (V2X) signals to restore model-based authority. Limitations and a path toward a constrained-QP predictive safety filter are discussed.

The enduring challenge in the field of artificial intelligence has been the control of systems to achieve desired behaviours. While for systems governed by straightforward dynamics equations, methods like Linear Quadratic Regulation (LQR) have historically proven highly effective, most real-world tasks, which require a general problem-solver, demand world models with dynamics that cannot be easily described by simple equations. Consequently, these models must be learned from data using neural networks. Most model predictive control (MPC) algorithms designed for visual world models have traditionally explored gradient-free population-based optimisation methods, such as Cross Entropy and Model Predictive Path Integral (MPPI) for planning. However, we present an exploration of a gradient-based alternative that fully leverages the differentiability of the world model. In our study, we conduct a comparative analysis between our method and other MPC-based alternatives, as well as policy-based algorithms. In a sample-efficient setting, our method achieves on par or superior performance compared to the alternative approaches in most tasks. Additionally, we introduce a hybrid model that combines policy networks and gradient-based MPC, which outperforms pure policy based methods thereby holding promise for Gradient-based planning with world models in complex real-world tasks.

Humanoid robots are promising to acquire various skills by imitating human behaviors. However, existing algorithms are only capable of tracking smooth, low-speed human motions, even with delicate reward and curriculum design. This paper presents a physics-based humanoid control framework, aiming to master highly-dynamic human behaviors such as Kungfu and dancing through multi-steps motion processing and adaptive motion tracking. For motion processing, we design a pipeline to extract, filter out, correct, and retarget motions, while ensuring compliance with physical constraints to the maximum extent. For motion imitation, we formulate a bi-level optimization problem to dynamically adjust the tracking accuracy tolerance based on the current tracking error, creating an adaptive curriculum mechanism. We further construct an asymmetric actor-critic framework for policy training. In experiments, we train whole-body control policies to imitate a set of highly-dynamic motions. Our method achieves significantly lower tracking errors than existing approaches and is successfully deployed on the Unitree G1 robot, demonstrating stable and expressive behaviors. The project page is https://kungfu-bot.github.io.

In policy gradient reinforcement learning, access to a differentiable model enables 1st-order gradient estimation that accelerates learning compared to relying solely on derivative-free 0th-order estimators. However, discontinuous dynamics cause bias and undermine the effectiveness of 1st-order estimators. Prior work addressed this bias by constructing a confidence interval around the REINFORCE 0th-order gradient estimator and using these bounds to detect discontinuities. However, the REINFORCE estimator is notoriously noisy, and we find that this method requires task-specific hyperparameter tuning and has low sample efficiency. This paper asks whether such bias is the primary obstacle and what minimal fixes suffice. First, we re-examine standard discontinuous settings from prior work and introduce DDCG, a lightweight test that switches estimators in nonsmooth regions; with a single hyperparameter, DDCG achieves robust performance and remains reliable with small samples. Second, on differentiable robotics control tasks, we present IVW-H, a per-step inverse-variance implementation that stabilizes variance without explicit discontinuity detection and yields strong results. Together, these findings indicate that while estimator switching improves robustness in controlled studies, careful variance control often dominates in practical deployments.

Unmanned vehicle navigation concerns estimating attitude, position, and linear velocity of the vehicle the six degrees of freedom (6 DoF). It has been known that the true navigation dynamics are highly nonlinear modeled on the Lie Group of SE_{2}(3). In this paper, a nonlinear filter for inertial navigation is proposed. The filter ensures systematic convergence of the error components starting from almost any initial condition. Also, the errors converge asymptotically to the origin. Experimental results validates the robustness of the proposed filter.

Probabilistic completeness is an important property in motion planning. Although it has been established with clear assumptions for geometric planners, the panorama of completeness results for kinodynamic planners is still incomplete, as most existing proofs rely on strong assumptions that are difficult, if not impossible, to verify on practical systems. In this paper, we focus on an important class of kinodynamic planners, namely those that interpolate trajectories in the state space. We provide a proof of probabilistic completeness for these planners under assumptions that can be readily verified from the system's equations of motion and the user-defined interpolation function. Our proof relies crucially on a property of interpolated trajectories, termed second-order continuity (SOC), which we show is tightly related to the ability of a planner to benefit from denser sampling. We analyze the impact of this property in simulations on a low-torque pendulum. Our results show that a simple RRT using a second-order continuous interpolation swiftly finds solution, while it is impossible for the same planner using standard Bezier curves (which are not SOC) to find any solution.

Video generation technologies are developing rapidly and have broad potential applications. Among these technologies, camera control is crucial for generating professional-quality videos that accurately meet user expectations. However, existing camera control methods still suffer from several limitations, including control precision and the neglect of the control for subject motion dynamics. In this work, we propose I2VControl-Camera, a novel camera control method that significantly enhances controllability while providing adjustability over the strength of subject motion. To improve control precision, we employ point trajectory in the camera coordinate system instead of only extrinsic matrix information as our control signal. To accurately control and adjust the strength of subject motion, we explicitly model the higher-order components of the video trajectory expansion, not merely the linear terms, and design an operator that effectively represents the motion strength. We use an adapter architecture that is independent of the base model structure. Experiments on static and dynamic scenes show that our framework outperformances previous methods both quantitatively and qualitatively. The project page is: https://wanquanf.github.io/I2VControlCamera .

Grey-box methods for system identification combine deep learning with physics-informed constraints, capturing complex dependencies while improving out-of-distribution generalization. Yet, despite the growing importance of floating-base systems such as humanoids and quadrupeds, current grey-box models ignore their specific physical constraints. For instance, the inertia matrix is not only positive definite but also exhibits branch-induced sparsity and input independence. Moreover, the 6x6 composite spatial inertia of the floating base inherits properties of single-rigid-body inertia matrices. As we show, this includes the triangle inequality on the eigenvalues of the composite rotational inertia. To address the lack of physical consistency in deep learning models of floating-base systems, we introduce a parameterization of inertia matrices that satisfies all these constraints. Inspired by Deep Lagrangian Networks (DeLaN), we train neural networks to predict physically plausible inertia matrices that minimize inverse dynamics error under Lagrangian mechanics. For evaluation, we collected and released a dataset on multiple quadrupeds and humanoids. In these experiments, our Floating-Base Deep Lagrangian Networks (FeLaN) achieve highly competitive performance on both simulated and real robots, while providing greater physical interpretability.

Recent progress in humanoid robots has unlocked agile locomotion skills, including backflipping, running, and crawling. Yet it remains challenging for a humanoid robot to perform forceful manipulation tasks such as moving objects, wiping, and pushing a cart. We propose adaptive Compliance Humanoid control through hIsight Perturbation (CHIP), a plug-and-play module that enables controllable end-effector stiffness while preserving agile tracking of dynamic reference motions. CHIP is easy to implement and requires neither data augmentation nor additional reward tuning. We show that a generalist motion-tracking controller trained with CHIP can perform a diverse set of forceful manipulation tasks that require different end-effector compliance, such as multi-robot collaboration, wiping, box delivery, and door opening.

The control of high-dimensional systems, such as soft robots, requires models that faithfully capture complex dynamics while remaining computationally tractable. This work presents a framework that integrates Graph Neural Network (GNN)-based dynamics models with structure-exploiting Model Predictive Control to enable real-time control of high-dimensional systems. By representing the system as a graph with localized interactions, the GNN preserves sparsity, while a tailored condensing algorithm eliminates state variables from the control problem, ensuring efficient computation. The complexity of our condensing algorithm scales linearly with the number of system nodes, and leverages Graphics Processing Unit (GPU) parallelization to achieve real-time performance. The proposed approach is validated in simulation and experimentally on a physical soft robotic trunk. Results show that our method scales to systems with up to 1,000 nodes at 100 Hz in closed-loop, and demonstrates real-time reference tracking on hardware with sub-centimeter accuracy, outperforming baselines by 63.6%. Finally, we show the capability of our method to achieve effective full-body obstacle avoidance.

We focus on developing efficient and reliable policy optimization strategies for robot learning with real-world data. In recent years, policy gradient methods have emerged as a promising paradigm for training control policies in simulation. However, these approaches often remain too data inefficient or unreliable to train on real robotic hardware. In this paper we introduce a novel policy gradient-based policy optimization framework which systematically leverages a (possibly highly simplified) first-principles model and enables learning precise control policies with limited amounts of real-world data. Our approach 1) uses the derivatives of the model to produce sample-efficient estimates of the policy gradient and 2) uses the model to design a low-level tracking controller, which is embedded in the policy class. Theoretical analysis provides insight into how the presence of this feedback controller addresses overcomes key limitations of stand-alone policy gradient methods, while hardware experiments with a small car and quadruped demonstrate that our approach can learn precise control strategies reliably and with only minutes of real-world data.

Temporal motion modeling has always been a key component in multiple object tracking (MOT) which can ensure smooth trajectory movement and provide accurate positional information to enhance association precision. However, current motion models struggle to be both efficient and effective across different application scenarios. To this end, we propose TrackSSM inspired by the recently popular state space models (SSM), a unified encoder-decoder motion framework that uses data-dependent state space model to perform temporal motion of trajectories. Specifically, we propose Flow-SSM, a module that utilizes the position and motion information from historical trajectories to guide the temporal state transition of object bounding boxes. Based on Flow-SSM, we design a flow decoder. It is composed of a cascaded motion decoding module employing Flow-SSM, which can use the encoded flow information to complete the temporal position prediction of trajectories. Additionally, we propose a Step-by-Step Linear (S^2L) training strategy. By performing linear interpolation between the positions of the object in the previous frame and the current frame, we construct the pseudo labels of step-by-step linear training, ensuring that the trajectory flow information can better guide the object bounding box in completing temporal transitions. TrackSSM utilizes a simple Mamba-Block to build a motion encoder for historical trajectories, forming a temporal motion model with an encoder-decoder structure in conjunction with the flow decoder. TrackSSM is applicable to various tracking scenarios and achieves excellent tracking performance across multiple benchmarks, further extending the potential of SSM-like temporal motion models in multi-object tracking tasks. Code and models are publicly available at https://github.com/Xavier-Lin/TrackSSM.

Whole-body motion tracking policies turn a humanoid into a robust control interface: the teleoperator---or an upstream model---only supplies a coarse movement intent, while the low-level policy keeps the robot balanced and physically feasible. Existing trackers deliver this interface only on flat ground: trained in empty scenes, they never learn how contact with terrain and objects reshapes their dynamics, and they attempt to teach the policy to balance under any command by continually enlarging the reference-motion corpus, which stops working once feasible behaviors become environment-dependent. We present GigaBrain-WBC-0.5, the first Behavior World Model (BWM) for humanoid whole-body control. Rather than a purely reactive tracker, we train a causal Transformer to jointly predict its next action, next state, and the distribution over its next latent behavior command, so the network that acts also models how the environment shapes what it can do next. An automatic terrain-annotation pipeline recovers full 3D contact geometry from retargeted motion, enabling terrain annotation at the scale of existing motion datasets. The predicted distribution is reused at deployment to detect implausible commands online and retract them onto learned behaviors, so the robot attempts tasks in a "best-effort" manner. The result is a unified policy that takes real-time command, interacts with environment, and stays robust to implausible commands, falls, and disturbances. GigaBrain-WBC-0.5 achieves the highest success rate across all four regimes among three large-scale tracker baselines: 81.3% on terrain interaction (4.3x the strongest baseline), 83.1% under implausible commands, and 99.3% fall recovery (16.8x the strongest baseline). Hardware trials show robust interaction under missing supports and disturbances; the Unitree G1 checkpoint transfers to the Maker L01 robot with simple fine-tuning.

Robust locomotion control depends on accurate state estimations. However, the sensors of most legged robots can only provide partial and noisy observations, making the estimation particularly challenging, especially for external states like terrain frictions and elevation maps. Inspired by the classical Internal Model Control principle, we consider these external states as disturbances and introduce Hybrid Internal Model (HIM) to estimate them according to the response of the robot. The response, which we refer to as the hybrid internal embedding, contains the robot's explicit velocity and implicit stability representation, corresponding to two primary goals for locomotion tasks: explicitly tracking velocity and implicitly maintaining stability. We use contrastive learning to optimize the embedding to be close to the robot's successor state, in which the response is naturally embedded. HIM has several appealing benefits: It only needs the robot's proprioceptions, i.e., those from joint encoders and IMU as observations. It innovatively maintains consistent observations between simulation reference and reality that avoids information loss in mimicking learning. It exploits batch-level information that is more robust to noises and keeps better sample efficiency. It only requires 1 hour of training on an RTX 4090 to enable a quadruped robot to traverse any terrain under any disturbances. A wealth of real-world experiments demonstrates its agility, even in high-difficulty tasks and cases never occurred during the training process, revealing remarkable open-world generalizability.

Kalman filter (KF) based methods for multi-object tracking (MOT) make an assumption that objects move linearly. While this assumption is acceptable for very short periods of occlusion, linear estimates of motion for prolonged time can be highly inaccurate. Moreover, when there is no measurement available to update Kalman filter parameters, the standard convention is to trust the priori state estimations for posteriori update. This leads to the accumulation of errors during a period of occlusion. The error causes significant motion direction variance in practice. In this work, we show that a basic Kalman filter can still obtain state-of-the-art tracking performance if proper care is taken to fix the noise accumulated during occlusion. Instead of relying only on the linear state estimate (i.e., estimation-centric approach), we use object observations (i.e., the measurements by object detector) to compute a virtual trajectory over the occlusion period to fix the error accumulation of filter parameters during the occlusion period. This allows more time steps to correct errors accumulated during occlusion. We name our method Observation-Centric SORT (OC-SORT). It remains Simple, Online, and Real-Time but improves robustness during occlusion and non-linear motion. Given off-the-shelf detections as input, OC-SORT runs at 700+ FPS on a single CPU. It achieves state-of-the-art on multiple datasets, including MOT17, MOT20, KITTI, head tracking, and especially DanceTrack where the object motion is highly non-linear. The code and models are available at https://github.com/noahcao/OC_SORT.

This work presents a novel reinforcement learning (RL) algorithm based on Y-wise Affine Neural Networks (YANNs). YANNs provide an interpretable neural network which can exactly represent known piecewise affine functions of arbitrary input and output dimensions defined on any amount of polytopic subdomains. One representative application of YANNs is to reformulate explicit solutions of multi-parametric linear model predictive control. Built on this, we propose the use of YANNs to initialize RL actor and critic networks, which enables the resulting YANN-RL control algorithm to start with the confidence of linear optimal control. The YANN-actor is initialized by representing the multi-parametric control solutions obtained via offline computation using an approximated linear system model. The YANN-critic represents the explicit form of the state-action value function for the linear system and the reward function as the objective in an optimal control problem (OCP). Additional network layers are injected to extend YANNs for nonlinear expressions, which can be trained online by directly interacting with the true complex nonlinear system. In this way, both the policy and state-value functions exactly represent a linear OCP initially and are able to eventually learn the solution of a general nonlinear OCP. Continuous policy improvement is also implemented to provide heuristic confidence that the linear OCP solution serves as an effective lower bound to the performance of RL policy. The YANN-RL algorithm is demonstrated on a clipped pendulum and a safety-critical chemical-reactive system. Our results show that YANN-RL significantly outperforms the modern RL algorithm using deep deterministic policy gradient, especially when considering safety constraints.

Whole-body loco-manipulation for quadruped robots with arms remains a challenging problem, particularly in achieving multi-task control. To address this, we propose MLM, a reinforcement learning framework driven by both real-world and simulation data. It enables a six-DoF robotic arm-equipped quadruped robot to perform whole-body loco-manipulation for multiple tasks autonomously or under human teleoperation. To address the problem of balancing multiple tasks during the learning of loco-manipulation, we introduce a trajectory library with an adaptive, curriculum-based sampling mechanism. This approach allows the policy to efficiently leverage real-world collected trajectories for learning multi-task loco-manipulation. To address deployment scenarios with only historical observations and to enhance the performance of policy execution across tasks with different spatial ranges, we propose a Trajectory-Velocity Prediction policy network. It predicts unobservable future trajectories and velocities. By leveraging extensive simulation data and curriculum-based rewards, our controller achieves whole-body behaviors in simulation and zero-shot transfer to real-world deployment. Ablation studies in simulation verify the necessity and effectiveness of our approach, while real-world experiments on a Go2 robot with an Airbot robotic arm demonstrate the policy's good performance in multi-task execution.

Ever since the original algorithm by Nesterov (1983), the true nature of the acceleration phenomenon has remained elusive, with various interpretations of why the method is actually faster. The diagnosis of the algorithm through the lens of Ordinary Differential Equations (ODEs) and the corresponding dynamical system formulation to explain the underlying dynamics has a rich history. In the literature, the ODEs that explain algorithms are typically derived by considering the limiting case of the algorithm maps themselves, that is, an ODE formulation follows the development of an algorithm. This obfuscates the underlying higher order principles and thus provides little evidence of the working of the algorithm. Such has been the case with Nesterov algorithm and the various analogies used to describe the acceleration phenomena, viz, momentum associated with the rolling of a Heavy-Ball down a slope, Hessian damping etc. The main focus of our work is to ideate the genesis of the Nesterov algorithm from the viewpoint of dynamical systems leading to demystifying the mathematical rigour behind the algorithm. Instead of reverse engineering ODEs from discrete algorithms, this work explores tools from the recently developed control paradigm titled Passivity and Immersion approach and the Geometric Singular Perturbation theory which are applied to arrive at the formulation of a dynamical system that explains and models the acceleration phenomena. This perspective helps to gain insights into the various terms present and the sequence of steps used in Nesterovs accelerated algorithm for the smooth strongly convex and the convex case. The framework can also be extended to derive the acceleration achieved using the triple momentum method and provides justifications for the non-convergence to the optimal solution in the Heavy-Ball method.

Visual loco-manipulation of arbitrary objects in the wild with humanoid robots requires accurate end-effector (EE) control and a generalizable understanding of the scene via visual inputs (e.g., RGB-D images). Existing approaches are based on real-world imitation learning and exhibit limited generalization due to the difficulty in collecting large-scale training datasets. This paper presents a new paradigm, HERO, for object loco-manipulation with humanoid robots that combines the strong generalization and open-vocabulary understanding of large vision models with strong control performance from simulated training. We achieve this by designing an accurate residual-aware EE tracking policy. This EE tracking policy combines classical robotics with machine learning. It uses a) inverse kinematics to convert residual end-effector targets into reference trajectories, b) a learned neural forward model for accurate forward kinematics, c) goal adjustment, and d) replanning. Together, these innovations help us cut down the end-effector tracking error by 3.2x. We use this accurate end-effector tracker to build a modular system for loco-manipulation, where we use open-vocabulary large vision models for strong visual generalization. Our system is able to operate in diverse real-world environments, from offices to coffee shops, where the robot is able to reliably manipulate various everyday objects (e.g., mugs, apples, toys) on surfaces ranging from 43cm to 92cm in height. Systematic modular and end-to-end tests in simulation and the real world demonstrate the effectiveness of our proposed design. We believe the advances in this paper can open up new ways of training humanoid robots to interact with daily objects.

We consider an improper reinforcement learning setting where a learner is given M base controllers for an unknown Markov decision process, and wishes to combine them optimally to produce a potentially new controller that can outperform each of the base ones. This can be useful in tuning across controllers, learnt possibly in mismatched or simulated environments, to obtain a good controller for a given target environment with relatively few trials. Towards this, we propose two algorithms: (1) a Policy Gradient-based approach; and (2) an algorithm that can switch between a simple Actor-Critic (AC) based scheme and a Natural Actor-Critic (NAC) scheme depending on the available information. Both algorithms operate over a class of improper mixtures of the given controllers. For the first case, we derive convergence rate guarantees assuming access to a gradient oracle. For the AC-based approach we provide convergence rate guarantees to a stationary point in the basic AC case and to a global optimum in the NAC case. Numerical results on (i) the standard control theoretic benchmark of stabilizing an cartpole; and (ii) a constrained queueing task show that our improper policy optimization algorithm can stabilize the system even when the base policies at its disposal are unstable.

Spring-based actuators in legged locomotion provide energy-efficiency and improved performance, but increase the difficulty of controller design. While previous work has focused on extensive modeling and simulation to find optimal controllers for such systems, we propose to learn model-free controllers directly on the real robot. In our approach, gaits are first synthesized by central pattern generators (CPGs), whose parameters are optimized to quickly obtain an open-loop controller that achieves efficient locomotion. Then, to make this controller more robust and further improve the performance, we use reinforcement learning to close the loop, to learn corrective actions on top of the CPGs. We evaluate the proposed approach on the DLR elastic quadruped bert. Our results in learning trotting and pronking gaits show that exploitation of the spring actuator dynamics emerges naturally from optimizing for dynamic motions, yielding high-performing locomotion, particularly the fastest walking gait recorded on bert, despite being model-free. The whole process takes no more than 1.5 hours on the real robot and results in natural-looking gaits.

The ability to track general whole-body motions in the real world is a useful way to build general-purpose humanoid robots. However, achieving this can be challenging due to the temporal and kinematic diversity of the motions, the policy's capability, and the difficulty of coordination of the upper and lower bodies. To address these issues, we propose GMT, a general and scalable motion-tracking framework that trains a single unified policy to enable humanoid robots to track diverse motions in the real world. GMT is built upon two core components: an Adaptive Sampling strategy and a Motion Mixture-of-Experts (MoE) architecture. The Adaptive Sampling automatically balances easy and difficult motions during training. The MoE ensures better specialization of different regions of the motion manifold. We show through extensive experiments in both simulation and the real world the effectiveness of GMT, achieving state-of-the-art performance across a broad spectrum of motions using a unified general policy. Videos and additional information can be found at https://gmt-humanoid.github.io.

Reinforcement Learning (RL) has shown great potential in refining robotic manipulation policies, yet its efficacy remains strongly bottlenecked by the difficulty of designing generalizable reward functions. In this paper, we propose a framework for online policy refinement by adapting foundation VLMs into online reward generators. We develop a robust, scalable reward model based on a state-of-the-art VLM, trained on a large-scale, multi-source dataset encompassing real-world robot trajectories, human-object interactions, and diverse simulated environments. Unlike prior approaches that evaluate entire trajectories post-hoc, our method leverages the VLM to formulate a multifaceted reward signal comprising process, completion, and temporal contrastive rewards based on current visual observations. Initializing with a base policy trained via Imitation Learning (IL), we employ these VLM rewards to guide the model to correct sub-optimal behaviors in a closed-loop manner. We evaluate our framework on challenging long-horizon manipulation benchmarks requiring sequential execution and precise control. Crucially, our reward model operates in a purely zero-shot manner within these test environments. Experimental results demonstrate that our method significantly improves the success rate of the initial IL policy within just 30 RL iterations, demonstrating remarkable sample efficiency. This empirical evidence highlights that VLM-generated signals can provide reliable feedback to resolve execution errors, effectively eliminating the need for manual reward engineering and facilitating efficient online refinement for robot learning.

Autonomous wire harness assembly requires robots to manipulate complex branched cables with high precision and reliability. A key challenge in automating this process is predicting how these flexible and branched structures behave under manipulation. Without accurate predictions, it is difficult for robots to reliably plan or execute assembly operations. While existing research has made progress in modeling single-threaded Deformable Linear Objects (DLOs), extending these approaches to Branched Deformable Linear Objects (BDLOs) presents fundamental challenges. The junction points in BDLOs create complex force interactions and strain propagation patterns that cannot be adequately captured by simply connecting multiple single-DLO models. To address these challenges, this paper presents Differentiable discrete branched Elastic rods for modeling Furcated DLOs in real-Time (DEFT), a novel framework that combines a differentiable physics-based model with a learning framework to: 1) accurately model BDLO dynamics, including dynamic propagation at junction points and grasping in the middle of a BDLO, 2) achieve efficient computation for real-time inference, and 3) enable planning to demonstrate dexterous BDLO manipulation. A comprehensive series of real-world experiments demonstrates DEFT's efficacy in terms of accuracy, computational speed, and generalizability compared to state-of-the-art alternatives. Project page:https://roahmlab.github.io/DEFT/.

We consider funnel control for linear infinite-dimensional systems that are impedance passive, meaning that they satisfy an energy balance in which the stored energy equals the squared norm of the state and the supplied power is the inner product of input and output. For the analysis we employ the system node approach, which offers a unified framework for infinite-dimensional systems with boundary and distributed control and observation. The resulting closed-loop dynamics are governed by a nonlinear evolution equation; we establish its solvability and hence the applicability of funnel control to this class. The applicability is illustrated by an Euler-Bernoulli beam, which is studied in two distinct scenarios: once with boundary control and once with distributed control.

Despite the rise of billion-parameter foundation models trained across thousands of GPUs, similar scaling gains have not been shown for humanoid control. Current neural controllers for humanoids remain modest in size, target a limited set of behaviors, and are trained on a handful of GPUs over several days. We show that scaling up model capacity, data, and compute yields a generalist humanoid controller capable of creating natural and robust whole-body movements. Specifically, we posit motion tracking as a natural and scalable task for humanoid control, leveraging dense supervision from diverse motion-capture data to acquire human motion priors without manual reward engineering. We build a foundation model for motion tracking by scaling along three axes: network size (from 1.2M to 42M parameters), dataset volume (over 100M frames, 700 hours of high-quality motion data), and compute (9k GPU hours). Beyond demonstrating the benefits of scale, we show the practical utility of our model through two mechanisms: (1) a real-time universal kinematic planner that bridges motion tracking to downstream task execution, enabling natural and interactive control, and (2) a unified token space that supports various motion input interfaces, such as VR teleoperation devices, human videos, and vision-language-action (VLA) models, all using the same policy. Scaling motion tracking exhibits favorable properties: performance improves steadily with increased compute and data diversity, and learned representations generalize to unseen motions, establishing motion tracking at scale as a practical foundation for humanoid control.

Model-based reinforcement learning is a powerful tool, but collecting data to fit an accurate model of the system can be costly. Exploring an unknown environment in a sample-efficient manner is hence of great importance. However, the complexity of dynamics and the computational limitations of real systems make this task challenging. In this work, we introduce FLEX, an exploration algorithm for nonlinear dynamics based on optimal experimental design. Our policy maximizes the information of the next step and results in an adaptive exploration algorithm, compatible with generic parametric learning models and requiring minimal resources. We test our method on a number of nonlinear environments covering different settings, including time-varying dynamics. Keeping in mind that exploration is intended to serve an exploitation objective, we also test our algorithm on downstream model-based classical control tasks and compare it to other state-of-the-art model-based and model-free approaches. The performance achieved by FLEX is competitive and its computational cost is low.