Daily Papers

We study joint downlink-uplink beamforming design for wireless federated learning (FL) with a multi-antenna base station. Considering analog transmission over noisy channels and uplink over-the-air aggregation, we derive the global model update expression over communication rounds. We then obtain an upper bound on the expected global loss function, capturing the downlink and uplink beamforming and receiver noise effect. We propose a low-complexity joint beamforming algorithm to minimize this upper bound, which employs alternating optimization to breakdown the problem into three subproblems, each solved via closed-form gradient updates. Simulation under practical wireless system setup shows that our proposed joint beamforming design solution substantially outperforms the conventional separate-link design approach and nearly attains the performance of ideal FL with error-free communication links.

This paper investigates the performance of network non-orthogonal multiple access (N-NOMA) in a downlink coordinated multi-point (CoMP) system. In the considered N-NOMA scheme, multiple base stations (BSs) cooperatively serve a CoMP user, meanwhile, each BS serves additional NOMA users by occupying the same resource block allocated to the CoMP user. The locations of the BSs and users are modeled by stochastic geometric models and the interference from the whole network is considered. Through rigorous derivations, the outage probabilities achieved by the CoMP and NOMA users are obtained, respectively. Numerical results are provided to verify the accuracy of the analytical results and also demonstrate the superior performance of N-NOMA compared to orthogonal multiple access (OMA) based CoMP scheme.

The potential of using of millimeter wave (mmWave) frequency for future wireless cellular communication systems has motivated the study of large-scale antenna arrays for achieving highly directional beamforming. However, the conventional fully digital beamforming methods which require one radio frequency (RF) chain per antenna element is not viable for large-scale antenna arrays due to the high cost and high power consumption of RF chain components in high frequencies. To address the challenge of this hardware limitation, this paper considers a hybrid beamforming architecture in which the overall beamformer consists of a low-dimensional digital beamformer followed by an RF beamformer implemented using analog phase shifters. Our aim is to show that such an architecture can approach the performance of a fully digital scheme with much fewer number of RF chains. Specifically, this paper establishes that if the number of RF chains is twice the total number of data streams, the hybrid beamforming structure can realize any fully digital beamformer exactly, regardless of the number of antenna elements. For cases with fewer number of RF chains, this paper further considers the hybrid beamforming design problem for both the transmission scenario of a point-to-point multipleinput multiple-output (MIMO) system and a downlink multiuser multiple-input single-output (MU-MISO) system. For each scenario, we propose a heuristic hybrid beamforming design that achieves a performance close to the performance of the fully digital beamforming baseline. Finally, the proposed algorithms are modified for the more practical setting in which only finite resolution phase shifters are available. Numerical simulations show that the proposed schemes are effective even when phase shifters with very low resolution are used.

Massive multiple-input multiple-output (MIMO) communication systems have a huge potential both in terms of data rate and energy efficiency, although channel estimation becomes challenging for a large number of antennas. Using a physical model allows to ease the problem by injecting a priori information based on the physics of propagation. However, such a model rests on simplifying assumptions and requires to know precisely the configuration of the system, which is unrealistic in practice.In this paper we present mpNet, an unfolded neural network specifically designed for massive MIMO channel estimation. It is trained online in an unsupervised way. Moreover, mpNet is computationally efficient and automatically adapts its depth to the signal-to-noise ratio (SNR). The method we propose adds flexibility to physical channel models by allowing a base station (BS) to automatically correct its channel estimation algorithm based on incoming data, without the need for a separate offline training phase.It is applied to realistic millimeter wave channels and shows great performance, achieving a channel estimation error almost as low as one would get with a perfectly calibrated system. It also allows incident detection and automatic correction, making the BS resilient and able to automatically adapt to changes in its environment.

The spectral smoothness properties of the low-frequency array of the Square Kilometer Array (SKA), namely SKA-Low, are an important issue for its scientific objectives to be attainable. A large array of 256 log-periodic dipole antennas, installed on top of a 42~m circular ground plane, will work as an SKA-Low station in the frequency range 50-350 MHz. In this article, the ground plane induced effects are examined in terms of antenna beam spectral characteristics, while different antenna placements are considered. Results are produced both at isolated antenna and at array level in the band 50-100 MHz, by employing an approximate method for the speeding-up of array simulations. We attempt to distinguish the ground plane effect from that of mutual coupling among antennas, which appears to be more severe at specific frequencies, using 2 figures of merit. The Discrete Fourier Transform (DFT) components of gain pattern ratios identify the fundamental spatial components of the ripple, while the Envelope Correlation Coefficient quantifies the penalty to considering an infinite ground plane.

The upper 6 GHz (U6G) band with XL-MIMO is a key enabler for sixth-generation wireless systems, yet intelligent radiomap prediction for such systems remains challenging. Existing datasets support only small-scale arrays (up to 8x8) with predominantly isotropic antennas, far from the 1024-element directional arrays envisioned for 6G. Moreover, current methods encode array configurations as scalar parameters, forcing neural networks to extrapolate array-specific radiation patterns, which fails when predicting radiomaps for configurations absent from training data. To jointly address data scarcity and generalization limitations, this paper advances XL-MIMO radiomap prediction from three aspects. To overcome data limitations, we construct the first XL-MIMO radiomap dataset containing 78400 radiomaps across 800 urban scenes, five frequency bands (1.8-6.7 GHz), and nine array configurations up to 32x32 uniform planar arrays with directional elements. To enable systematic evaluation, we establish a comprehensive benchmark framework covering practical scenarios from coverage estimation without field measurements to generalization across unseen configurations and environments. To enable generalization to arbitrary beam configurations without retraining, we propose the beam map, a physics-informed spatial feature that analytically computes array-specific coverage patterns. By decoupling deterministic array radiation from data learned multipath propagation, beam maps shift generalization from neural network extrapolation to physics-based computation. Integrating beam maps into existing architectures reduces mean absolute error by up to 60.0% when generalizing to unseen configurations and up to 50.5% when transferring to unseen environments. The complete dataset and code are publicly available at https://lxj321.github.io/MulticonfigRadiomapDataset/.

An important concept in the fifth generation of mobile networks is multitenancy, which allows diverse operators sharing the same wireless infrastructure. To support this feature in conjunction with the challenging performance requirements of future networks, more automated and faster planning of the required radio capacity is needed. Likewise, installing small cells is an effective resource to provide greater performance and capacity to both indoor and outdoor places. This paper proposes a new framework for automated cell planning in multitenant small cell networks. In particular, taking advantage of the available network data, a set of detailed planning specifications over time and space domains are generated in order to meet the contracted capacity by each tenant. Then, the network infrastructure and configuration are updated according to an algorithm that considers different actions such as adding/removing channels and adding or relocating small cells. The simulation results show the effectiveness of various methods to derive the planning specifications depending on the correlation between the tenant's and network's traffic demands.

Deep learning is widely used in wireless communications but struggles with fixed neural network sizes, which limit their adaptability in environments where the number of users and antennas varies. To overcome this, this paper introduced a generalization strategy for precoding and power allocation in scalable wireless networks. Initially, we employ an innovative approach to abstract the wireless network into a homogeneous graph. This primarily focuses on bypassing the heterogeneous features between transmitter (TX) and user entities to construct a virtual homogeneous graph serving optimization objectives, thereby enabling all nodes in the virtual graph to share the same neural network. This "TX entity" is known as a base station (BS) in cellular networks and an access point (AP) in cell-free networks. Subsequently, we design a universal graph neural network, termed the information carrying graph neural network (ICGNN), to capture and integrate information from this graph, maintaining permutation invariance. Lastly, using ICGNN as the core algorithm, we tailor the neural network's input and output for specific problem requirements and validate its performance in two scenarios: 1) in cellular networks, we develop a matrix-inverse-free multi-user multi-input multi-output (MU-MIMO) precoding scheme using the conjugate gradient (CG) method, adaptable to varying user and antenna numbers; 2) in a cell-free network, facing dynamic variations in the number of users served by APs, the number of APs serving each user, and the number of antennas per AP, we propose a universal power allocation scheme. Simulations demonstrate that the proposed approach not only significantly reduces computational complexity but also achieves, and potentially exceeds, the spectral efficiency (SE) of conventional algorithms.

The potential of applying diffusion models (DMs) for multiple antenna communications is discussed. A unified framework of applying DM for multiple antenna tasks is first proposed. Then, the tasks are innovatively divided into two categories, i.e., decision-making tasks and generation tasks, depending on whether an optimization of system parameters is involved. For each category, it is conceived 1) how the framework can be used for each task and 2) why the DM is superior to traditional artificial intelligence (TAI) and conventional optimization tasks. It is highlighted that the DMs are well-suited for scenarios with strong interference and noise, excelling in modeling complex data distribution and exploring better actions. A case study of learning beamforming with a DM is then provided, to demonstrate the superiority of the DMs with simulation results. Finally, the applications of DM for emerging multiple antenna technologies and promising research directions are discussed.

An isotropic antenna radiates and receives electromagnetic wave uniformly in magnitude in 3D space. A multi-frequency quasi-isotropic antenna can serve as a practically feasible solution to emulate an ideal multi-frequency isotropic radiator. It is also an essential technology for mobile smart devices for massive IoT in the upcoming 6G. However, ever since the quasi-isotropic antenna was proposed and achieved more than half a century ago, at most two discrete narrow frequency bands can be achieved, because of the significantly increased structural complexity from multi-frequency isotropic radiation. This limitation impedes numerous related electromagnetic experiments and the advances in wireless communication. Here, for the first time, a design method for multi-band (>2) quasi-isotropic antennas is proposed. An exemplified quasi-isotropic antenna with the desired four frequency bands is also presented for demonstration. The measured results validate excellent performance on both electromagnetics and wireless communications for this antenna.

Mobile users (or UEs, to use 3GPP terminology) served by small cells in dense urban settings may abruptly experience a significant deterioration in their channel to their serving base stations (BSs) in several scenarios, such as after turning a corner around a tall building, or a sudden knot of traffic blocking the direct path between the UE and its serving BS. In this work, we propose a scheme to temporarily increase the data rate to/from this UE with additional bandwidth from the nearest Coordinated Multi-Point (CoMP) cluster of BSs, while the slower process of handover of the UE to a new serving BS is ongoing. We emphasize that this additional bandwidth is additional to the data rates the UE is getting over its primary connection to the current serving BS and, after the handover, to the new serving BS. The key novelty of the present work is the proposal of a decentralized market-based resource allocation method to perform resource allocation to support Coordinated Beamforming (CB) CoMP. It is scalable to large numbers of UEs and BSs, and it is fast because resource allocations are made bilaterally, between BSs and UEs. Once the resource allocation to the UE has been made, the coordinated of transmissions occurs as per the usual CB methods. Thus the proposed method has the benefit of giving the UE access to its desired amount of resources fast, without waiting for handover to complete, or reporting channel state information before it knows the resources it will be allocated for receiving transmissions from the serving BS.

Integrated sensing and communication (ISAC) has been recognized as one of the key technologies capable of simultaneously improving communication and sensing services in future wireless networks. Moreover, the introduction of recently developed movable antennas (MAs) has the potential to further increase the performance gains of ISAC systems. Achieving these gains can pose a significant challenge for MA-enabled ISAC systems operating in the near-field due to the corresponding spherical wave propagation. Motivated by this, in this paper we maximize the weighted sum rate (WSR) for communication users while maintaining a minimal sensing requirement in an MA-enabled near-field ISAC system. To achieve this goal, we propose an algorithm that optimizes the sensing receive combiner, the communication precoding matrices, the sensing transmit beamformer and the positions of the users' MAs in an alternating manner. Simulation results show that using MAs in near-field ISAC systems provides a substantial performance advantage compared to near-field ISAC systems with only fixed antennas. Additionally, we demonstrate that the highest WSR is obtained when larger weights are allocated to the users placed closer to the BS, and that the sensing performance is significantly more affected by the minimum sensing signal-to-interference-plus-noise ratio (SINR) threshold compared to the communication performance.

The use of mmWave frequencies is one of the key strategies to achieve the fascinating 1000x increase in the capacity of future 5G wireless systems. While for traditional sub-6 GHz cellular frequencies several well-developed statistical channel models are available for system simulation, similar tools are not available for mmWave frequencies, thus preventing a fair comparison of independently developed transmission and reception schemes. In this paper we provide a simple albeit accurate statistical procedure for the generation of a clustered MIMO channel model operating at mmWaves, for both the cases of slowly and rapidly time-varying channels. Matlab scripts for channel generation are also provided, along with an example of their use.

Passive space-borne radiometers operating in the 1400-1427 MHz protected frequency band face radio frequency interference (RFI) from terrestrial sources. With the growth of wireless devices and the appearance of new technologies, the possibility of sharing this spectrum with other technologies would introduce more RFI to these radiometers. This band could be an ideal mid-band frequency for 5G and Beyond, as it offers high capacity and good coverage. Current RFI detection and mitigation techniques at SMAP (Soil Moisture Active Passive) depend on correctly detecting and discarding or filtering the contaminated data leading to the loss of valuable information, especially in severe RFI cases. In this paper, we propose an autoencoder-based RFI mitigation method to remove the dominant RFI caused by potential coexistent terrestrial users (i.e., 5G base station) from the received contaminated signal at the passive receiver side, potentially preserving valuable information and preventing the contaminated data from being discarded.

The joint transmit and pinching beamforming design for spectral efficiency (SE) and energy efficiency (EE) tradeoff in pinching-antenna systems (PASS) is proposed. Both PASS-enabled single- and multi-user communications are considered. In the single-user scenario, it is proved that the optimal pinching antenna (PA) positions are independent of the transmit beamforming. Based on this insight, a two-stage joint beamforming design is proposed. Specifically, in the first stage, an iterative closed-form refinement (ICR) scheme is proposed to align the phases of the received signals, based on which a PA placement framework is proposed. In the second stage, the closed-form solution for the optimal transmit beamformer is derived given the optimal PA positions. In the multi-user scenario, an alternating optimization (AO)-based joint beamforming design is proposed to balance the SE-EE performance while taking the quality-of-service (QoS) requirements into account. It is proved that the proposed AO-based algorithm is guaranteed to converge when no constraints are violated in PA placement subproblem. Numerical results demonstrate that: 1) the proposed algorithms significantly improve joint SE-EE performance with fast convergence speed; 2) the SE-EE tradeoff regime gap between PASS and conventional multi-antenna system widens as the number of PAs and service coverage increase.

The introduction of fifth-generation (5G) radio technology has revolutionized communications, bringing unprecedented automation, capacity, connectivity, and ultra-fast, reliable communications. However, this technological leap comes with a substantial increase in energy consumption, presenting a significant challenge. To improve the energy efficiency of 5G networks, it is imperative to develop sophisticated models that accurately reflect the influence of base station (BS) attributes and operational conditions on energy usage.Importantly, addressing the complexity and interdependencies of these diverse features is particularly challenging, both in terms of data processing and model architecture design. This paper proposes a novel 5G base stations energy consumption modelling method by learning from a real-world dataset used in the ITU 5G Base Station Energy Consumption Modelling Challenge in which our model ranked second. Unlike existing methods that omit the Base Station Identifier (BSID) information and thus fail to capture the unique energy fingerprint in different base stations, we incorporate the BSID into the input features and encoding it with an embedding layer for precise representation. Additionally, we introduce a novel masked training method alongside an attention mechanism to further boost the model's generalization capabilities and accuracy. After evaluation, our method demonstrates significant improvements over existing models, reducing Mean Absolute Percentage Error (MAPE) from 12.75% to 4.98%, leading to a performance gain of more than 60%.

Beam codebooks are a new feature of massive multiple-input multiple-output (M-MIMO) in 5G new radio (NR). Codebooks comprised of beamforming vectors are used to transmit reference signals and obtain limited channel state information (CSI) from receivers via the codeword index. This enables large arrays that cannot otherwise obtain sufficient CSI. The performance, however, is limited by the codebook design. In this paper, we show that machine learning can be used to train site-specific codebooks for initial access. We design a neural network based on an autoencoder architecture that uses a beamspace observation in combination with RF environment characteristics to improve the synchronization signal (SS) burst codebook. We test our algorithm using a flexible dataset of channels generated from QuaDRiGa. The results show that our model outperforms the industry standard (DFT beams) and approaches the optimal performance (perfect CSI and singular value decomposition (SVD)-based beamforming), using only a few bits of feedback.

This letter investigates a short-packet downlink transmission system using non-orthogonal multiple access (NOMA) enhanced via movable antenna (MA). We focuses on maximizing the effective throughput for a core user while ensuring reliable communication for an edge user by optimizing the MAs' coordinates and the power and rate allocations from the access point (AP). The optimization challenge is approached by decomposing it into two subproblems, utilizing successive convex approximation (SCA) to handle the highly non-concave nature of channel gains. Numerical results confirm that the proposed solution offers substantial improvements in effective throughput compared to NOMA short-packet communication with fixed position antennas (FPAs).

Super-directive antenna arrays have faced challenges in achieving high realized gains ever since their introduction in the academic literature. The primary challenges are high impedance mismatches and resistive losses, which become increasingly more dominant as the number of elements increases. Consequently, a critical limitation arises in determining the maximum number of elements that should be utilized to achieve super-directivity, particularly within dense array configurations. This paper addresses precisely this issue through an optimization study to design a super-directive antenna array with a maximum number of elements. An iterative approach is employed to increase the array of elements while sustaining a satisfactory realized gain using the differential evolution (DE) algorithm. Thus, it is observed that super-directivity can be obtained in an array with a maximum of five elements. Our results indicate that the obtained unit array has a 67.20% higher realized gain than a uniform linear array with conventional excitation. For these reasons, these results make the proposed architecture a strong candidate for applications that require densely packed arrays, particularly in the context of massive multiple-input multiple-output (MIMO).

The quickly increasing data traffic and the user demand for a full coverage of mobile services anywhere and anytime are leading mobile networking into a future of small cell networks. However, due to the high-density and randomness of small cell networks, there are several technical challenges. In this paper, we investigate two critical issues: best signal quality and mobility management. Under the assumptions that base stations are uniformly distributed in a ring shaped region and that shadowings are lognormal, independent and identically distributed, we prove that when the number of sites in the ring tends to infinity, then (i) the maximum signal strength received at the center of the ring tends in distribution to a Gumbel distribution when properly renormalized, and (ii) it is asymptotically independent of the interference. Using these properties, we derive the distribution of the best signal quality. Furthermore, an optimized random cell scanning scheme is proposed, based on the evaluation of the optimal number of sites to be scanned for maximizing the user data throughput.

This paper investigates a Stacked Intelligent Metasurfaces (SIM)-assisted Integrated Sensing and Communications (ISAC) system. An extended target model is considered, where the BS aims to estimate the complete target response matrix relative to the SIM. Under the constraints of minimum Signal-to-Interference-plus-Noise Ratio (SINR) for the communication users (CUs) and maximum transmit power, we jointly optimize the transmit beamforming at the base station (BS) and the end-to-end transmission matrix of the SIM, to minimize the Cramér-Rao Bound (CRB) for target estimation. Effective algorithms such as the alternating optimization (AO) and semidefinite relaxation (SDR) are employed to solve the non-convex SINR-constrained CRB minimization problem. Finally, we design and build an experimental platform for SIM, and evaluate the performance of the proposed algorithms for communication and sensing tasks.

WiFi Channel State Information (CSI)-based human activity recognition (HAR) enables contactless, long-range sensing in spatially constrained environments while preserving visual privacy. However, despite the presence of numerous WiFi-enabled devices around us, few expose CSI to users, resulting in a lack of sensing hardware options. Variants of the Espressif ESP32 have emerged as potential low-cost and easy-to-deploy solutions for WiFi CSI-based HAR. In this work, four ESP32-S3-based 2.4GHz directional antenna systems are evaluated for their ability to facilitate long-range through-wall HAR. Two promising systems are proposed, one of which combines the ESP32-S3 with a directional biquad antenna. This combination represents, to the best of our knowledge, the first demonstration of such a system in WiFi-based HAR. The second system relies on the built-in printed inverted-F antenna (PIFA) of the ESP32-S3 and achieves directionality through a plane reflector. In a comprehensive evaluation of line-of-sight (LOS) and non-line-of-sight (NLOS) HAR performance, both systems are deployed in an office environment spanning a distance of 18 meters across five rooms. In this experimental setup, the Wallhack1.8k dataset, comprising 1806 CSI amplitude spectrograms of human activities, is collected and made publicly available. Based on Wallhack1.8k, we train activity recognition models using the EfficientNetV2 architecture to assess system performance in LOS and NLOS scenarios. For the core NLOS activity recognition problem, the biquad antenna and PIFA-based systems achieve accuracies of 92.0pm3.5 and 86.8pm4.7, respectively, demonstrating the feasibility of long-range through-wall HAR with the proposed systems.

As 5G technology becomes increasingly established, the anticipation for 6G is growing, which promises to deliver faster and more reliable wireless connections via cutting-edge radio technologies. However, efficient management method of the large-scale antenna arrays deployed by those radio technologies is crucial. Traditional management methods are mainly reactive, usually based on feedback from users to adapt to the dynamic wireless channel. However, a more promising approach lies in the prediction of spatial channel state information (spatial-CSI), which is an all-inclusive channel characterization and consists of all the feasible line-of-sight (LoS) and non-line-of-sight (NLoS) paths between the transmitter (Tx) and receiver (Rx), with the three-dimension (3D) trajectory, attenuation, phase shift, delay, and polarization of each path. Advances in hardware and neural networks make it possible to predict such spatial-CSI using precise environmental information, and further look into the possibility of holographic communication, which implies complete control over every aspect of the radio waves emitted. Based on the integration of holographic communication and digital twin, we proposed a new framework, digital radio twin, which takes advantages from both the digital world and deterministic control over radio waves, supporting a wide range of high-level applications. As a preliminary attempt towards this visionary direction, in this paper, we explore the use of generative artificial intelligence (AI) to pinpoint the valid paths in a given environment, demonstrating promising results, and highlighting the potential of this approach in driving forward the evolution of 6G wireless communication technologies.

We propose an innovative machine learning-based technique to address the problem of channel acquisition at the base station in frequency division duplex systems. In this context, the base station reconstructs the full channel state information in the downlink frequency range based on limited downlink channel state information feedback from the mobile terminal. The channel state information recovery is based on a convolutional neural network which is trained exclusively on collected channel state samples acquired in the uplink frequency domain. No acquisition of training samples in the downlink frequency range is required at all. Finally, after a detailed presentation and analysis of the proposed technique and its performance, the "transfer learning'' assumption of the convolutional neural network that is central to the proposed approach is validated with an analysis based on the maximum mean discrepancy metric.

Shifting 6G-and-beyond wireless communication systems to higher frequency bands and the utilization of massive multiple-input multiple-output arrays will extend the near-field region, affecting beamforming and user localization schemes. In this paper, we propose a localization-based beam-focusing strategy that leverages the dominant line-of-sight (LoS) propagation arising at mmWave and sub-THz frequencies. To support this approach, we analyze the 2D-MUSIC algorithm for distance estimation by examining its spectrum in simplified, tractable setups with minimal numbers of antennas and users. Lastly, we compare the proposed localization-based beam focusing, with locations estimated via 2D-MUSIC, with zero forcing with pilot-based channel estimation in terms of uplink sum spectral efficiency. Our numerical results show that the proposed method becomes more effective under LoS-dominated propagation, short coherence blocks, and strong noise power arising at high carrier frequencies and with large bandwidths.

An effective way to realize non-orthogonal multiple access (NOMA) assisted grant-free transmission is to first create multiple receive signal-to-noise ratio (SNR) levels and then serve multiple grant-free users by employing these SNR levels as bandwidth resources. These SNR levels need to be pre-configured prior to the grant-free transmission and have great impact on the performance of grant-free networks. The aim of this letter is to illustrate different designs for configuring the SNR levels and investigate their impact on the performance of grant-free transmission, where age-of-information is used as the performance metric. The presented analytical and simulation results demonstrate the performance gain achieved by NOMA over orthogonal multiple access, and also reveal the relative merits of the considered designs for pre-configured SNR levels.

We present MiMo-7B, a large language model born for reasoning tasks, with optimization across both pre-training and post-training stages. During pre-training, we enhance the data preprocessing pipeline and employ a three-stage data mixing strategy to strengthen the base model's reasoning potential. MiMo-7B-Base is pre-trained on 25 trillion tokens, with additional Multi-Token Prediction objective for enhanced performance and accelerated inference speed. During post-training, we curate a dataset of 130K verifiable mathematics and programming problems for reinforcement learning, integrating a test-difficulty-driven code-reward scheme to alleviate sparse-reward issues and employing strategic data resampling to stabilize training. Extensive evaluations show that MiMo-7B-Base possesses exceptional reasoning potential, outperforming even much larger 32B models. The final RL-tuned model, MiMo-7B-RL, achieves superior performance on mathematics, code and general reasoning tasks, surpassing the performance of OpenAI o1-mini. The model checkpoints are available at https://github.com/xiaomimimo/MiMo.

Holographic Metasurface Transceivers (HMTs) are emerging as cost-effective substitutes to large antenna arrays for beamforming in Millimeter and TeraHertz wave communication. However, to achieve desired channel gains through beamforming in HMT, phase-shifts of a large number of elements need to be appropriately set, which is challenging. Also, these optimal phase-shifts depend on the location of the receivers, which could be unknown. In this work, we develop a learning algorithm using a {\it fixed-budget multi-armed bandit framework} to beamform and maximize received signal strength at the receiver for far-field regions. Our algorithm, named \Algo exploits the parametric form of channel gains of the beams, which can be expressed in terms of two {\it phase-shifting parameters}. Even after parameterization, the problem is still challenging as phase-shifting parameters take continuous values. To overcome this, {\it\HB} works with the discrete values of phase-shifting parameters and exploits their unimodal relations with channel gains to learn the optimal values faster. We upper bound the probability of {\it\HB} incorrectly identifying the (discrete) optimal phase-shift parameters in terms of the number of pilots used in learning. We show that this probability decays exponentially with the number of pilot signals. We demonstrate that {\it\HB} outperforms state-of-the-art algorithms through extensive simulations.

Classification between different activities in an indoor environment using wireless signals is an emerging technology for various applications, including intrusion detection, patient care, and smart home. Researchers have shown different methods to classify activities and their potential benefits by utilizing WiFi signals. In this paper, we analyze classification of moving objects by employing machine learning on real data from a massive multi-input-multi-output (MIMO) system in an indoor environment. We conduct measurements for different activities in both line-of-sight and non line-of-sight scenarios with a massive MIMO testbed operating at 3.7 GHz. We propose algorithms to exploit amplitude and phase-based features classification task. For the considered setup, we benchmark the classification performance and show that we can achieve up to 98% accuracy using real massive MIMO data, even with a small number of experiments. Furthermore, we demonstrate the gain in performance results with a massive MIMO system as compared with that of a limited number of antennas such as in WiFi devices.