Daily Papers

As the conventional scaling of logic devices comes to an end, functional wafer backside and 3D transistor stacking are consensus for next-generation logic technology, offering considerable design space extension for powers, signals or even devices on the wafer backside. The Flip FET (FFET), a novel transistor architecture combining 3D transistor stacking and fully functional wafer backside, was recently proposed. With symmetric dual-sided standard cell design, the FFET can deliver around 12.5% cell area scaling and faster but more energy-efficient libraries beyond other stacked transistor technologies such as CFET. Besides, thanks to the novel cell design with dual-sided pins, the FFET supports dual-sided signal routing, delivering better routability and larger backside design space. In this work, we demonstrated a comprehensive FFET evaluation framework considering physical implementation and block-level power-performance-area (PPA) assessment for the first time, in which key functions are dual-sided routing and dual-sided RC extraction. A 32-bit RISC-V core was used for the evaluation here. Compared to the CFET with single-sided signals, the FFET with single-sided signals achieved 23.3% post-P&R core area reduction, 25.0% higher frequency and 11.9% lower power at the same utilization, and 16.0 % higher frequency at the same core area. Meanwhile, the FFET supports dual-sided signals, which can further benefit more from flexible allocation of cell input pins on both sides. By optimizing the input pin density and BEOL routing layer number on each side, 10.6% frequency gain was realized without power degradation compared to the one with single-sided signal routing. Moreover, the routability and power efficiency of FFET barely degrades even with the routing layer number reduced from 12 to 5 on each side, validating the great space for cost-friendly design enabled by FFET.

Open-source EDA shows promising potential in unleashing EDA innovation and lowering the cost of chip design. This paper presents an open-source EDA project, iEDA, aiming for building a basic infrastructure for EDA technology evolution and closing the industrial-academic gap in the EDA area. iEDA now covers the whole flow of physical design (including Floorplan, Placement, CTS, Routing, Timing Optimization etc.), and part of the analysis tools (Static Timing Analysis and Power Analysis). To demonstrate the effectiveness of iEDA, we implement and tape out three chips of different scales (from 700k to 1.5M gates) on different process nodes (110nm and 28nm) with iEDA. iEDA is publicly available from the project home page http://ieda.oscc.cc.

Recent years have witnessed the outstanding success of deep learning in various fields such as vision and natural language processing. This success is largely indebted to the massive size of deep learning models that is expected to increase unceasingly. This growth of the deep learning models is accompanied by issues related to their considerable energy consumption, both during the training and inference phases, as well as their scalability. Although a number of work based on unconventional physical systems have been proposed which addresses the issue of energy efficiency in the inference phase, efficient training of deep learning models has remained unaddressed. So far, training of digital deep learning models mainly relies on backpropagation, which is not suitable for physical implementation as it requires perfect knowledge of the computation performed in the so-called forward pass of the neural network. Here, we tackle this issue by proposing a simple deep neural network architecture augmented by a biologically plausible learning algorithm, referred to as "model-free forward-forward training". The proposed architecture enables training deep physical neural networks consisting of layers of physical nonlinear systems, without requiring detailed knowledge of the nonlinear physical layers' properties. We show that our method outperforms state-of-the-art hardware-aware training methods by improving training speed, decreasing digital computations, and reducing power consumption in physical systems. We demonstrate the adaptability of the proposed method, even in systems exposed to dynamic or unpredictable external perturbations. To showcase the universality of our approach, we train diverse wave-based physical neural networks that vary in the underlying wave phenomenon and the type of non-linearity they use, to perform vowel and image classification tasks experimentally.

Post-route power recovery changes cell choices under tightly coupled timing, electrical and physical constraints, and the value of each change depends on what it costs to repair its side effects. We propose an AI-driven framework in which a learned model drives both phases of the optimization: it ranks the powerrecovery edits to try and the repair actions that follow, while deterministic electronic design automation (EDA) analyses govern every acceptance. The framework records baseline constraint margins, identifies the damage a recovery transaction introduces in each analysis view, holds pre-existing violations at their baseline rather than working them inside the power step, and caps repair spending at a fraction of the measured saving. An ensemble of gradient-boosted models predicts power change, normalized damage reduction and constraint-regression risk from action and timing-context features available before each trial; calibrated, conservative estimates feed separate acquisition scores for recovery and repair, with a deterministic fallback when the model is uncertain. Recovery and repair remain speculative until physical implementation and fresh analysis establish baseline preservation and positive net saving. We specify the contract, the learned policy, the transactional flow and a pre-registered public evaluation protocol on open designs. Evidence from a companion study on public designs supports the contract; the learned policy is proposed, and no trained-model results or proprietary design measurements are reported.

This article provides an introduction to surface code quantum computing. We first estimate the size and speed of a surface code quantum computer. We then introduce the concept of the stabilizer, using two qubits, and extend this concept to stabilizers acting on a two-dimensional array of physical qubits, on which we implement the surface code. We next describe how logical qubits are formed in the surface code array and give numerical estimates of their fault-tolerance. We outline how logical qubits are physically moved on the array, how qubit braid transformations are constructed, and how a braid between two logical qubits is equivalent to a controlled-NOT. We then describe the single-qubit Hadamard, S and T operators, completing the set of required gates for a universal quantum computer. We conclude by briefly discussing physical implementations of the surface code. We include a number of appendices in which we provide supplementary information to the main text.

Computational sensing strategies often suffer from calibration errors in the physical implementation of their ideal sensing models. Such uncertainties are typically addressed by using multiple, accurately chosen training signals to recover the missing information on the sensing model, an approach that can be resource-consuming and cumbersome. Conversely, blind calibration does not employ any training signal, but corresponds to a bilinear inverse problem whose algorithmic solution is an open issue. We here address blind calibration as a non-convex problem for linear random sensing models, in which we aim to recover an unknown signal from its projections on sub-Gaussian random vectors, each subject to an unknown positive multiplicative factor (or gain). To solve this optimisation problem we resort to projected gradient descent starting from a suitable, carefully chosen initialisation point. An analysis of this algorithm allows us to show that it converges to the exact solution provided a sample complexity requirement is met, i.e., relating convergence to the amount of information collected during the sensing process. Interestingly, we show that this requirement grows linearly (up to log factors) in the number of unknowns of the problem. This sample complexity is found both in absence of prior information, as well as when subspace priors are available for both the signal and gains, allowing a further reduction of the number of observations required for our recovery guarantees to hold. Moreover, in the presence of noise we show how our descent algorithm yields a solution whose accuracy degrades gracefully with the amount of noise affecting the measurements. Finally, we present some numerical experiments in an imaging context, where our algorithm allows for a simple solution to blind calibration of the gains in a sensor array.

Fringe projection profilometry (FPP) has been established as a high-accuracy 3D reconstruction method capable of achieving sub-pixel accuracy. However, this technique faces significant constraints due to complex calibration requirements, bulky system footprint, and sensitivity to environmental conditions. To address these limitations, we present VIRTUS-FPP, the first comprehensive physics-based virtual sensor modeling framework for FPP built in NVIDIA Isaac Sim. By leveraging the physics-based rendering and programmable sensing capabilities of simulation, our framework enables end-to-end modeling from calibration to reconstruction with full mathematical fidelity to the underlying principles of structured light. We conduct comprehensive virtual calibration and validate our system's reconstruction accuracy through quantitative comparison against ground truth geometry. Additionally, we demonstrate the ability to model the virtual system as a digital twin by replicating a physical FPP system in simulation and validating correspondence between virtual and real-world measurements. Experimental results demonstrate that VIRTUS-FPP accurately models optical phenomena critical to FPP and achieves results comparable to real-world systems while offering unprecedented flexibility for system configuration, sensor prototyping, and environmental control. This framework significantly accelerates the development of real-world FPP systems by enabling rapid virtual prototyping before physical implementation.

Scaling laws for Large Language Models (LLMs) establish that model quality improves with computational scale, yet edge deployment imposes strict constraints on compute, memory, and power. Since General Matrix Multiplication (GEMM) accounts for up to 90% of inference time, efficient GEMM acceleration is critical for edge AI. The Adaptive Intelligent Engines available in the AMD Versal adaptive SoCs are well suited for this task, but existing state-of-the-art (SOTA) frameworks maximize performance through spatial scaling, distributing workloads across hundreds of cores -- an approach that fails on resource-limited edge SoCs due to physical implementation failures, bandwidth saturation, and excessive resource consumption. We propose Tempus, a Resource-Invariant Temporal GEMM framework for the AMD Versal AI Edge SoC. Rather than expanding hardware resources with matrix size, Tempus employs a fixed compute block of 16 AIE-ML cores, achieving scalability through iterative graph execution and algorithmic data tiling and replication in the Programmable Logic. High-speed cascade streaming ensures low-latency partial sum reduction at Initiation Interval (II) of 1, while a deadlock-free DATAFLOW protocol maximizes transfer-compute overlap and PLIO reuse. Evaluated on GEMM workloads, Tempus achieves 607 GOPS at 10.677 W total on-chip power. By characterizing system-level efficiency through the Platform-Aware Utility (PAU) metric, we prove that Tempus achieves a 211.2x higher prominence factor than the leading spatial SOTA (ARIES). Furthermore, the framework maintains a 0.00% utilization of URAM/DSP, yielding 22.0x core frugality, 7.1x power frugality, and a 6.3x reduction in I/O demand, establishing a sustainable, scalable foundation for edge LLM inference.

Agent-based modeling has been around for decades, and applied widely across the social and natural sciences. The scope of this research method is now poised to grow dramatically as it absorbs the new affordances provided by Large Language Models (LLM)s. Generative Agent-Based Models (GABM) are not just classic Agent-Based Models (ABM)s where the agents talk to one another. Rather, GABMs are constructed using an LLM to apply common sense to situations, act "reasonably", recall common semantic knowledge, produce API calls to control digital technologies like apps, and communicate both within the simulation and to researchers viewing it from the outside. Here we present Concordia, a library to facilitate constructing and working with GABMs. Concordia makes it easy to construct language-mediated simulations of physically- or digitally-grounded environments. Concordia agents produce their behavior using a flexible component system which mediates between two fundamental operations: LLM calls and associative memory retrieval. A special agent called the Game Master (GM), which was inspired by tabletop role-playing games, is responsible for simulating the environment where the agents interact. Agents take actions by describing what they want to do in natural language. The GM then translates their actions into appropriate implementations. In a simulated physical world, the GM checks the physical plausibility of agent actions and describes their effects. In digital environments simulating technologies such as apps and services, the GM may handle API calls to integrate with external tools such as general AI assistants (e.g., Bard, ChatGPT), and digital apps (e.g., Calendar, Email, Search, etc.). Concordia was designed to support a wide array of applications both in scientific research and for evaluating performance of real digital services by simulating users and/or generating synthetic data.

We present DiffTaichi, a new differentiable programming language tailored for building high-performance differentiable physical simulators. Based on an imperative programming language, DiffTaichi generates gradients of simulation steps using source code transformations that preserve arithmetic intensity and parallelism. A light-weight tape is used to record the whole simulation program structure and replay the gradient kernels in a reversed order, for end-to-end backpropagation. We demonstrate the performance and productivity of our language in gradient-based learning and optimization tasks on 10 different physical simulators. For example, a differentiable elastic object simulator written in our language is 4.2x shorter than the hand-engineered CUDA version yet runs as fast, and is 188x faster than the TensorFlow implementation. Using our differentiable programs, neural network controllers are typically optimized within only tens of iterations.

Unmanned aerial vehicles (UAVs) are cyber-physical systems whose attack surface spans networked avionics and on-board sensor fusion: a compromised GPS or battery module can mimic a benign mission segment and evade naive anomaly detectors. We present a leakage-free evaluation of quantum machine learning for UAV anomaly detection on the multi-sensor TLM:UAV benchmark. Three contributions support the study. (i) A group-aware temporal protocol (B2) partitions the dataset into ten contiguous TimeUS blocks and evaluates over ten seeds, eliminating the inflation produced by random stratified splits that mix neighbouring samples. (ii) A three-mode feature audit (full/loose/strict) quantifies how much accuracy stems from instantaneous physical signals versus contextual proxies (cumulative energy, battery state, GPS trajectory). (iii) A hybrid XGBoost + Data Reuploading (DRU) classifier is benchmarked against five paired non-linear controls (raw, PCA, polynomial-2, random-RBF, and an untrained DRU map) under identical budgets. The standalone DRU does not consistently match the strongest classical baseline across seeds; however, the trained-DRU hybrid is the only model whose mean F1 macro shifts upward from full to strict (+0.05), a directional signal that the per-seed standard deviations prevent from being interpreted as a statistically established difference. The trained-DRU hybrid also records the lowest mean false-alarm rate under proxy-free evaluation, subject to the inter-seed variance reported. We frame this as an incremental, reproducible quantum-enhanced hybrid benefit, and provide an open Qiskit 2.x implementation as a benchmark for cybersecurity analytics in NISQ-era aerospace systems.

Large Language Models (LLMs) have demonstrated remarkable capabilities across various domains, including software development, education, and technical assistance. Among these, software development is one of the key areas where LLMs are increasingly adopted. However, when hardware constraints are considered-for instance, in physical computing, where software must interact with and control physical hardware -their effectiveness has not been fully explored. To address this gap, we introduce PCEval (Physical Computing Evaluation), the first benchmark in physical computing that enables a fully automatic evaluation of the capabilities of LLM in both the logical and physical aspects of the projects, without requiring human assessment. Our evaluation framework assesses LLMs in generating circuits and producing compatible code across varying levels of project complexity. Through comprehensive testing of 13 leading models, PCEval provides the first reproducible and automatically validated empirical assessment of LLMs' ability to reason about fundamental hardware implementation constraints within a simulation environment. Our findings reveal that while LLMs perform well in code generation and logical circuit design, they struggle significantly with physical breadboard layout creation, particularly in managing proper pin connections and avoiding circuit errors. PCEval advances our understanding of AI assistance in hardware-dependent computing environments and establishes a foundation for developing more effective tools to support physical computing education.

Transportation Cyber-Physical Systems (T-CPS) enhance safety and mobility by integrating cyber and physical transportation systems. A key component of T-CPS is the Digital Twin (DT), a virtual representation that enables simulation, analysis, and optimization through real-time data exchange and communication. Although existing studies have explored DTs for vehicles, communications, pedestrians, and traffic, real-world validations and implementations of DTs that encompass infrastructure, vehicles, signals, communications, and more remain limited due to several challenges. These include accessing real-world connected infrastructure, integrating heterogeneous, multi-sourced data, ensuring real-time data processing, and synchronizing the digital and physical systems. To address these challenges, this study develops a traffic DT based on a real-world connected vehicle corridor. Leveraging the Cellular Vehicle-to-Everything (C-V2X) infrastructure in the corridor, along with communication, computing, and simulation technologies, the proposed DT accurately replicates physical vehicle behaviors, signal timing, communications, and traffic patterns within the virtual environment. Building upon the previous data pipeline, the digital system ensures robust synchronization with the physical environment. Moreover, the DT's scalable and redundant architecture enhances data integrity, making it capable of supporting future large-scale C-V2X deployments. Furthermore, its ability to provide feedback to the physical system is demonstrated through applications such as signal timing adjustments, vehicle advisory messages, and incident notifications. The proposed DT is a vital tool in T-CPS, enabling real-time traffic monitoring, prediction, and optimization to enhance the reliability and safety of transportation systems.

In VLSI physical design, many algorithms require the solution of difficult combinatorial optimization problems such as max/min-cut, max-flow problems etc. Due to the vast number of elements typically found in this problem domain, these problems are computationally intractable leading to the use of approximate solutions. In this work, we explore the Ising spin glass model as a solution methodology for hard combinatorial optimization problems using the general purpose GPU (GPGPU). The Ising model is a mathematical model of ferromagnetism in statistical mechanics. Ising computing finds a minimum energy state for the Ising model which essentially corresponds to the expected optimal solution of the original problem. Many combinatorial optimization problems can be mapped into the Ising model. In our work, we focus on the max-cut problem as it is relevant to many VLSI physical design problems. Our method is inspired by the observation that Ising annealing process is very amenable to fine-grain massive parallel GPU computing. We will illustrate how the natural randomness of GPU thread scheduling can be exploited during the annealing process to create random update patterns and allow better GPU resource utilization. Furthermore, the proposed GPU-based Ising computing can handle any general Ising graph with arbitrary connections, which was shown to be difficult for existing FPGA and other hardware based implementation methods. Numerical results show that the proposed GPU Ising max-cut solver can deliver more than 2000X speedup over the CPU version of the algorithm on some large examples, which shows huge performance improvement for addressing many hard optimization algorithms for practical VLSI physical design.

Unsupervised physical parameter estimation from video lacks a common benchmark: existing methods evaluate on non-overlapping synthetic data, the sole real-world dataset is restricted to single-body systems, and no established protocol addresses governing-equation identification. This work introduces IRIS, a high-fidelity benchmark comprising 240 real-world videos captured at 4K resolution and 60fps, spanning both single- and multi-body dynamics with independently measured ground-truth parameters and uncertainty estimates. Each dynamical system is recorded under controlled laboratory conditions and paired with its governing equations, enabling principled evaluation. A standardized evaluation protocol is defined encompassing parameter accuracy, identifiability, extrapolation, robustness, and governing-equation selection. Multiple baselines are evaluated, including a multi-step physics loss formulation and four complementary equation-identification strategies (VLM temporal reasoning, describe-then-classify prompting, CNN-based classification, and path-based labelling), establishing reference performance across all IRIS scenarios and exposing systematic failure modes that motivate future research. The dataset, annotations, evaluation toolkit, and all baseline implementations are publicly released.

The rapid advancement of Large Language Models (LLMs) has marked a significant breakthrough in Artificial Intelligence (AI), ushering in a new era of Human-centered Artificial Intelligence (HAI). HAI aims to better serve human welfare and needs, thereby placing higher demands on the intelligence level of robots, particularly in aspects such as natural language interaction, complex task planning, and execution. Intelligent agents powered by LLMs have opened up new pathways for realizing HAI. However, existing LLM-based embodied agents often lack the ability to plan and execute complex natural language control tasks online. This paper explores the implementation of intelligent robotic manipulating agents based on Vision-Language Models (VLMs) in the physical world. We propose a novel embodied agent framework for robots, which comprises a human-robot voice interaction module, a vision-language agent module and an action execution module. The vision-language agent itself includes a vision-based task planner, a natural language instruction converter, and a task performance feedback evaluator. Experimental results demonstrate that our agent achieves a 28\% higher average task success rate in both simulated and real environments compared to approaches relying solely on LLM+CLIP, significantly improving the execution success rate of high-level natural language instruction tasks.

Modular quantum processors require a compiler to reason about two resources at the same time: local device connectivity and communication across QPUs. A mapping that is acceptable on a single coupling graph may be unsuitable for a modular machine if it creates excessive cross-QPU traffic, concentrates that traffic on a small number of interconnect links, or assigns many boundary qubits to a QPU with few communication ports. This paper presents QuPort, a Python and Qiskit-based compilation framework that studies this setting through an explicit three-level model: a weighted logical interaction graph, a directed physical coupling map, and an undirected QPU-level interconnect graph. The main partitioning method, TPCCAP, optimizes the implemented objective formed by weighted cut distance, communication-port overflow, and routed link-load congestion. The framework also includes heavy-edge clustering, balanced greedy partitioning, simulated-annealing refinement, communication-port-aware layout, extraction of remote two-qubit operations, local-only routing of per-QPU circuits, and topology-aware schedule estimation. The model is a compiler-level abstraction. It does not claim a calibrated hardware runtime or an implementation of a physical remote-gate protocol.

We present a new approach for evaluating Feynman integrals numerically. We apply the recently-proposed framework of physics-informed deep learning to train neural networks to approximate the solution to the differential equations satisfied by the Feynman integrals. This approach relies neither on a canonical form of the differential equations, which is often a bottleneck for the analytical techniques, nor on the availability of a large dataset, and after training yields essentially instantaneous evaluation times. We provide a proof-of-concept implementation within the PyTorch framework, and apply it to a number of one- and two-loop examples, achieving a mean magnitude of relative difference of around 1% at two loops in the physical phase space with network training times on the order of an hour on a laptop GPU.

Here we present a machine learning framework and model implementation that can learn to simulate a wide variety of challenging physical domains, involving fluids, rigid solids, and deformable materials interacting with one another. Our framework---which we term "Graph Network-based Simulators" (GNS)---represents the state of a physical system with particles, expressed as nodes in a graph, and computes dynamics via learned message-passing. Our results show that our model can generalize from single-timestep predictions with thousands of particles during training, to different initial conditions, thousands of timesteps, and at least an order of magnitude more particles at test time. Our model was robust to hyperparameter choices across various evaluation metrics: the main determinants of long-term performance were the number of message-passing steps, and mitigating the accumulation of error by corrupting the training data with noise. Our GNS framework advances the state-of-the-art in learned physical simulation, and holds promise for solving a wide range of complex forward and inverse problems.

A Sense/Compute/Control (SCC) application is one that interacts with the physical environment. Such applications are pervasive in domains such as building automation, assisted living, and autonomic computing. Developing an SCC application is complex because: (1) the implementation must address both the interaction with the environment and the application logic; (2) any evolution in the environment must be reflected in the implementation of the application; (3) correctness is essential, as effects on the physical environment can have irreversible consequences. The SCC architectural pattern and the DiaSpec domain-specific design language propose a framework to guide the design of such applications. From a design description in DiaSpec, the DiaSpec compiler is capable of generating a programming framework that guides the developer in implementing the design and that provides runtime support. In this paper, we report on an experiment using DiaSpec (both the design language and compiler) to develop a standard robotics application. We discuss the benefits and problems of using DiaSpec in a robotics setting and present some changes that would make DiaSpec a better framework in this setting.

With the rapid progress of diffusion models and large-scale video generation, generative world models are increasingly expected to replace traditional simulators, including physics engines, game engines, and reinforcement-learning environments. Yet the remaining distance from generation to simulation lacks a systematic assessment. We present a capability-based study using an external yardstick: eight capabilities of a traditional simulator, namely asset construction, physics engine, interaction, controllability, stability, state feedback, diversity, and evaluation metrics. We trace three main technical routes--latent dynamics, video generation, and joint-embedding prediction--and map exactly 200 representative works published from 2018 to June 2026 onto these capabilities. Our analysis shows that world models have achieved functional substitution in interaction and controllability for specific scenarios, but remain short of traditional simulators in formal guarantees of physical laws, structured state feedback, and reproducible long-horizon evolution. State feedback is the most neglected cross-route shortcoming: only 6 of 163 implementation papers expose a runtime interface for querying entity states or physical parameters. We identify six research directions: formalized physics, a unified action interface, first-class state feedback, long-horizon stability, downstream-utility evaluation, and cross-route hybridization. Project page: https://github.com/AtongWang/world-model-simulators

Cooperative driving, enabled by communication between automated vehicle systems, promises significant benefits to fuel efficiency, road capacity, and safety over single-vehicle driver assistance systems such as adaptive cruise control (ACC). However, the responsible development and implementation of these algorithms poses substantial challenges due to the need for extensive real-world testing. We address this issue and introduce OpenConvoy, an open and extensible framework designed for the implementation and assessment of cooperative driving policies on physical connected and autonomous vehicles (CAVs). We demonstrate the capabilities of OpenConvoy through a series of experiments on a convoy of multi-scale vehicles controlled by Platooning to show the stability of our system across vehicle configurations and its ability to effectively measure convoy cohesion across driving scenarios including varying degrees of communication loss.

Artificial neural networks have become a staple computing technique in many fields. Yet, they present fundamental differences with classical computing hardware in the way they process information. Photonic implementations of neural network architectures potentially offer fundamental advantages over their electronic counterparts in terms of speed, processing parallelism, scalability and energy efficiency. Scalable and high performance photonic neural networks (PNNs) have been demonstrated, yet they remain scarce. In this work, we study the performance of such a scalable, fully parallel and autonomous PNN based on a large area vertical-cavity surface-emitting laser (LA-VCSEL). We show how the performance varies with different physical parameters, namely, injection wavelength, injection power, and bias current. Furthermore, we link these physical parameters to the general computational measures of consistency and dimensionality. We present a general method of gauging dimensionality in high dimensional nonlinear systems subject to noise, which could be applied to many systems in the context of neuromorphic computing. Our work will inform future implementations of spatially multiplexed VCSEL PNNs.

Quantum theory departs from classical physics in its treatment of correlations, most prominently through the phenomena of contextuality and nonlocality. Once regarded primarily as foundational curiosities, these effects are now understood as key operational resources for quantum computation, communication, and simulation. Although traditionally investigated in distinct settings, recent theoretical and experimental advances have revealed deep conceptual, mathematical, and operational connections between them. This review presents a unified perspective on these developments based on sheaf-theoretic and graph-theoretic frameworks, which provide theory-independent characterizations of statistical correlations. These approaches clarify the structural relationship between contextuality and nonlocality, facilitate the formulation of experimentally testable inequalities, and guide implementations in realistic physical platforms, with particular emphasis on photonic systems. By bridging abstract theoretical structures and concrete experimental realizations, this review sheds light on the nonclassical foundations of quantum correlations and their emerging role in quantum technologies.

When will robots have their ChatGPT moment? Such a breakthrough requires a general-purpose robot that can handle unfamiliar tasks in unfamiliar environments, remain controllable over long interactions, and learn from experience. Today's embodied systems largely follow an end-to-end observation-to-action path. Despite rapid progress, they remain far from this goal: their generalization depends heavily on the coverage of robot training data, while long task execution remains difficult to control and inspect. To realize this goal, we introduce the Embodied Task Agent (ETA), a new paradigm for extending digital agents into the physical world, and release OpenETA as its open-source implementation. ETA centers the robot around a Planner that chooses one Tool call at a time, an Interface that controls execution, and a World that returns the result and a fresh observation. This loop allows the agent to verify outcomes, adapt its plan, and turn successful and failed interactions into reusable experience. OpenETA provides replaceable Planners, composable Tools and Skills, auditable memory, replayable trajectories, and common interfaces for simulation and real robots. For Codex, OpenETA can operate as a lightweight plugin that exposes only observe, mark_point, and move_to.

Large Language Models (LLMs) have demonstrated strong performance across general NLP tasks, but their utility in automating numerical experiments of complex physical system -- a critical and labor-intensive component -- remains underexplored. As the major workhorse of computational science over the past decades, Computational Fluid Dynamics (CFD) offers a uniquely challenging testbed for evaluating the scientific capabilities of LLMs. We introduce CFDLLMBench, a benchmark suite comprising three complementary components -- CFDQuery, CFDCodeBench, and FoamBench -- designed to holistically evaluate LLM performance across three key competencies: graduate-level CFD knowledge, numerical and physical reasoning of CFD, and context-dependent implementation of CFD workflows. Grounded in real-world CFD practices, our benchmark combines a detailed task taxonomy with a rigorous evaluation framework to deliver reproducible results and quantify LLM performance across code executability, solution accuracy, and numerical convergence behavior. CFDLLMBench establishes a solid foundation for the development and evaluation of LLM-driven automation of numerical experiments for complex physical systems. Code and data are available at https://github.com/NREL-Theseus/cfdllmbench/.

World models are central to building agents that can reason, plan, and generalize beyond their training data. However, research on world models is currently fragmented, with disparate codebases, data pipelines, and evaluation protocols hindering reproducibility and fair comparison. Current practice is further limited by three key bottlenecks: fragile one-off codebases, slow video data loading, and the lack of standardized generalization benchmarks. We present stable-worldmodel (swm), an open-source platform for standardized and reproducible world modeling research and evaluation. It delivers (1) a high-performance Lance-based data layer with native support and conversion tools for MP4, HDF5, and LeRobot datasets, (2) clean, well-tested implementations of modern world model baselines and planning solvers, and (3) a broad suite of environments and tasks extended with controllable visual, geometric, and physical factors of variation for systematic in-silico evaluation of dynamics understanding, control performance, representation quality, and out-of-distribution generalization. By unifying the full pipeline under a single, scalable framework, swm dramatically reduces research overhead and accelerates trustworthy progress toward reliable world models.

Synthesizing physics-grounded 3D assets is a critical bottleneck for interactive virtual worlds and embodied AI. Existing methods predominantly focus on static geometry, overlooking the functional properties essential for interaction. We propose that interactive asset generation must be rooted in functional logic and hierarchical physics. To bridge this gap, we introduce PhysForge, a decoupled two-stage framework supported by PhysDB, a large-scale dataset of 150,000 assets with four-tier physical annotations. First, a VLM acts as a "physical architect" to plan a "Hierarchical Physical Blueprint" defining material, functional, and kinematic constraints. Second, a physics-grounded diffusion model realizes this blueprint by synthesizing high-fidelity geometry alongside precise kinematic parameters via a novel KineVoxel Injection (KVI) mechanism. Experiments demonstrate that PhysForge produces functionally plausible, simulation-ready assets, providing a robust data engine for interactive 3D content and embodied agents.

Image editing has achieved remarkable progress recently. Modern editing models could already follow complex instructions to manipulate the original content. However, beyond completing the editing instructions, the accompanying physical effects are the key to the generation realism. For example, removing an object should also remove its shadow, reflections, and interactions with nearby objects. Unfortunately, existing models and benchmarks mainly focus on instruction completion but overlook these physical effects. So, at this moment, how far are we from physically realistic image editing? To answer this, we introduce PICABench, which systematically evaluates physical realism across eight sub-dimension (spanning optics, mechanics, and state transitions) for most of the common editing operations (add, remove, attribute change, etc). We further propose the PICAEval, a reliable evaluation protocol that uses VLM-as-a-judge with per-case, region-level human annotations and questions. Beyond benchmarking, we also explore effective solutions by learning physics from videos and construct a training dataset PICA-100K. After evaluating most of the mainstream models, we observe that physical realism remains a challenging problem with large rooms to explore. We hope that our benchmark and proposed solutions can serve as a foundation for future work moving from naive content editing toward physically consistent realism.

Predictive Physical AI systems output state rollouts, action chunks, and latent plans, yet a low root-mean-square error (RMSE) does not imply that a particular proposal is physically executable. We formulate physical admissibility as a prediction-control interface: before execution, a decoded proposal is treated as candidate dynamics and evaluated using kinematic, dynamic, and direct-to-composed horizon conditions. Passing is not a certificate of task success; rejection identifies violation of the specified physical envelope and gives a component-level reason. On Hugging Face LeRobot PushT, controlled falsification shows that one-step prediction-RMSE and standardized dynamics residuals reach area under the receiver operating characteristic curve (AUC) 0.982 and 0.972, kinematic-only conditions reach AUC 0.592, and the full gate reaches AUC 0.957 with condition-level attribution. In replay-based intervention experiments, residual-based filters and the full physical-admissibility gate prevent 87-$89% of invalid proposals while preserving mean progress near 0.998.

Recent advances in physical 3D generation have enabled visually faithful assets with simulatable mechanical behavior. However, existing methods provide limited control over material behavior beyond appearance-based inference and struggle to estimate physical properties from complex interactions between objects and semantic parts. Therefore, we present PhysForge, a Video Diffusion Model (VDM)-based framework for addressing these challenges, comprising two complementary modules for material-controllable physical fitting and componentlevel interaction modeling. The first, PhysFit, leverages material-conditioned VDM dynamics as references for physical-property fitting, introducing windowed fitting to focus on material-revealing interactions and Hallucinated Forcing to disentangle nonphysical motion hallucinated by the VDM from material responses. The second, PhysComp decomposes complex interactions into individual objects and semantic components, enabling their physical parameters to be optimized independently and flexibly composed for joint simulation. Experiments on PhysAssets and Google Scanned Objects demonstrate that, compared with existing methods, PhysForge provides stronger control over material-dependent physical responses while supporting component-level physical modeling for complex interactions. It achieves the best CLIP and physical controllability scores on both common and uncommon materials, with qualitative comparisons, component-level ablations, and a user study further supporting these improvements. Our project page is available at https://masterwanna.github.io/PhysForge.html .

World models for embodied AI must be physically viable: constructed to answer intervention queries by representing the physical structure governing action outcomes, rather than merely predicting future observations. Existing observation-predictive world models can produce visually plausible but physically wrong rollouts. This failure is structural; distinct physical systems can look identical yet diverge under intervention. We expose this problem with controlled benchmarks that fix the visible scene while varying latent physics. We show that such models may recommend infeasible actions, mispredict interaction outcomes, or certify unsafe behavior. We argue that embodied AI requires world models that identify the simplest physical abstraction sufficient to answer an intervention query. Such a model comprises modular components, including environment representation, latent state and parameter estimation, action specification, interventional dynamics, and query-level response. An autonomous orchestrator should identify the relevant abstraction and compose compatible learned and structured components per query. When closed-form physics is unavailable, uncertain, or costly, the transition model may be analytic, simulated, learned, or hybrid, but it must preserve the structure that determines interventional outcomes. This decomposition makes the model interpretable, its components verifiable, and its outputs auditable against the query. It also provides a design principle for new world models and a feasibility test for existing ones: the right abstraction is not the most detailed model of the world, but the simplest model that preserves the distinctions relevant to the query. We demonstrate this approach on queries that existing systems fail to answer correctly, and outline how an orchestrator can dynamically assemble and adapt physically viable models for planning, control, and verification.

Recent rapid advancements in text-to-video (T2V) generation, such as SoRA and Kling, have shown great potential for building world simulators. However, current T2V models struggle to grasp abstract physical principles and generate videos that adhere to physical laws. This challenge arises primarily from a lack of clear guidance on physical information due to a significant gap between abstract physical principles and generation models. To this end, we introduce the World Simulator Assistant (WISA), an effective framework for decomposing and incorporating physical principles into T2V models. Specifically, WISA decomposes physical principles into textual physical descriptions, qualitative physical categories, and quantitative physical properties. To effectively embed these physical attributes into the generation process, WISA incorporates several key designs, including Mixture-of-Physical-Experts Attention (MoPA) and a Physical Classifier, enhancing the model's physics awareness. Furthermore, most existing datasets feature videos where physical phenomena are either weakly represented or entangled with multiple co-occurring processes, limiting their suitability as dedicated resources for learning explicit physical principles. We propose a novel video dataset, WISA-32K, collected based on qualitative physical categories. It consists of 32,000 videos, representing 17 physical laws across three domains of physics: dynamics, thermodynamics, and optics. Experimental results demonstrate that WISA can effectively enhance the compatibility of T2V models with real-world physical laws, achieving a considerable improvement on the VideoPhy benchmark. The visual exhibitions of WISA and WISA-32K are available in the https://360cvgroup.github.io/WISA/.

Part-aware 3D asset generation enables applications such as editing, articulation, simulation, and fabrication, yet existing methods can generate visually complete individual parts without ensuring that they form a valid physical assembly. Consequently, generated neighboring parts may interpenetrate, lack valid connections, or collapse under gravity. We propose a physics-guided framework for improving single-image part-aware 3D generation with physically compatible geometry and stable connections. Our method resolves inter-part penetration, recovers a contact graph between neighboring parts, and introduces parameterized connectors at their contact surfaces. Using feedback from physical simulation, we refine connector placement, orientation, and dimensions to improve assembly stability while preserving the generated geometry. We further introduce a physics-based evaluation protocol that complements conventional geometric metrics by directly testing assembly validity and stability under gravity. Experiments comparing against multiple part-aware 3D generators show substantial improvements in physical realizability and stability while maintaining geometric quality. We additionally validate the resulting parts through 3D printing and real-world assembly.

Recent diffusion-based video generation models can synthesize visually plausible videos, yet they often struggle to satisfy physical constraints. A key reason is that most existing approaches remain single-stage: they entangle high-level physical understanding with low-level visual synthesis, making it hard to generate content that require explicit physical reasoning. To address this limitation, we propose a training-free three-stage pipeline,PhyRPR:Phy\uline{Reason}--Phy\uline{Plan}--Phy\uline{Refine}, which decouples physical understanding from visual synthesis. Specifically, PhyReason uses a large multimodal model for physical state reasoning and an image generator for keyframe synthesis; PhyPlan deterministically synthesizes a controllable coarse motion scaffold; and PhyRefine injects this scaffold into diffusion sampling via a latent fusion strategy to refine appearance while preserving the planned dynamics. This staged design enables explicit physical control during generation. Extensive experiments under physics constraints show that our method consistently improves physical plausibility and motion controllability.

LLM-based LEGO assembly generation requires both semantic grounding and physical feasibility. We identify a data-induced failure mode, PhysHack, in which the assemblies satisfy physical-validity constraints while producing structures that are geometrically misaligned, semantically inconsistent, or poorly calibrated. To address this challenge, we propose a model-based data selection approach that uses only a small fraction of the training data while improving physically grounded LEGO assembly generation. Building on the selected trajectories, we introduce PVPO, a sample-efficient reinforcement learning method that couples physical feasibility with voxel-space geometric rewards. Our results show that physical validity alone is an insufficient proxy for reliable physical reasoning: models can learn to generate valid structures without preserving semantic or geometric fidelity. Experiments across model backbones and test-time scaling settings demonstrate that PVPO improves structural and semantic alignment, physical validity, structural stability, and calibration, while reducing reliance on extensive post-hoc rejection sampling. In particular, results on calibration show that PVPO mitigates PhysHack by making test-time selection more predictive of semantic and structural quality.

We investigate how to enhance the physical fidelity of video generation models by leveraging synthetic videos derived from computer graphics pipelines. These rendered videos respect real-world physics, such as maintaining 3D consistency, and serve as a valuable resource that can potentially improve video generation models. To harness this potential, we propose a solution that curates and integrates synthetic data while introducing a method to transfer its physical realism to the model, significantly reducing unwanted artifacts. Through experiments on three representative tasks emphasizing physical consistency, we demonstrate its efficacy in enhancing physical fidelity. While our model still lacks a deep understanding of physics, our work offers one of the first empirical demonstrations that synthetic video enhances physical fidelity in video synthesis. Website: https://kevinz8866.github.io/simulation/

Physics reasoning requires constructing a consistent model of the underlying physical system rather than relying solely on symbolic or formula-based manipulation. Although large language models have shown strong ability in solving math and coding problems, they still struggle with physics problems, as these problems entangle the physical modeling process with mathematical calculations. Humans approach physics by first building a representation of the system before performing calculations. Inspired by this, we introduce a unified framework that distills intermediate representations that explicitly encode the physical modeling process and adopt a two-stage post-training strategy, where supervised fine-tuning establishes structured modeling, and reinforcement learning with rubric-based feedback improves the quality of the modeling process. Experiments on multiple multimodal physics benchmarks show that our approach leads to consistent improvements in reasoning performance across different models and datasets. On PhysReason, PhyX and SeePhys benchmarks, physical modeling output performs GRPO by an average ~3%, showing that explicit physical modeling is an efficient strategy of improving physics reasoning for small LLMs.

We present a computational framework that transforms single images into 3D physical objects. The visual geometry of a physical object in an image is determined by three orthogonal attributes: mechanical properties, external forces, and rest-shape geometry. Existing single-view 3D reconstruction methods often overlook this underlying composition, presuming rigidity or neglecting external forces. Consequently, the reconstructed objects fail to withstand real-world physical forces, resulting in instability or undesirable deformation -- diverging from their intended designs as depicted in the image. Our optimization framework addresses this by embedding physical compatibility into the reconstruction process. We explicitly decompose the three physical attributes and link them through static equilibrium, which serves as a hard constraint, ensuring that the optimized physical shapes exhibit desired physical behaviors. Evaluations on a dataset collected from Objaverse demonstrate that our framework consistently enhances the physical realism of 3D models over existing methods. The utility of our framework extends to practical applications in dynamic simulations and 3D printing, where adherence to physical compatibility is paramount.

Recent advances of data-driven machine learning have revolutionized fields like computer vision, reinforcement learning, and many scientific and engineering domains. In many real-world and scientific problems, systems that generate data are governed by physical laws. Recent work shows that it provides potential benefits for machine learning models by incorporating the physical prior and collected data, which makes the intersection of machine learning and physics become a prevailing paradigm. By integrating the data and mathematical physics models seamlessly, it can guide the machine learning model towards solutions that are physically plausible, improving accuracy and efficiency even in uncertain and high-dimensional contexts. In this survey, we present this learning paradigm called Physics-Informed Machine Learning (PIML) which is to build a model that leverages empirical data and available physical prior knowledge to improve performance on a set of tasks that involve a physical mechanism. We systematically review the recent development of physics-informed machine learning from three perspectives of machine learning tasks, representation of physical prior, and methods for incorporating physical prior. We also propose several important open research problems based on the current trends in the field. We argue that encoding different forms of physical prior into model architectures, optimizers, inference algorithms, and significant domain-specific applications like inverse engineering design and robotic control is far from being fully explored in the field of physics-informed machine learning. We believe that the interdisciplinary research of physics-informed machine learning will significantly propel research progress, foster the creation of more effective machine learning models, and also offer invaluable assistance in addressing long-standing problems in related disciplines.

Machine learning approaches to spatiotemporal physical systems have primarily focused on next-frame prediction, with the goal of learning an accurate emulator for the system's evolution in time. However, these emulators are computationally expensive to train and are subject to performance pitfalls, such as compounding errors during autoregressive rollout. In this work, we take a different perspective and look at scientific tasks further downstream of predicting the next frame, such as estimation of a system's governing physical parameters. Accuracy on these tasks offers a uniquely quantifiable glimpse into the physical relevance of the representations of these models. We evaluate the effectiveness of general-purpose self-supervised methods in learning physics-grounded representations that are useful for downstream scientific tasks. Surprisingly, we find that not all methods designed for physical modeling outperform generic self-supervised learning methods on these tasks, and methods that learn in the latent space (e.g., joint embedding predictive architectures, or JEPAs) outperform those optimizing pixel-level prediction objectives. Code is available at https://github.com/helenqu/physical-representation-learning.

Evaluations of LLM planning agents largely ask whether a task succeeds or a declared plan is followed. In strategic cyber-physical systems, a stronger question is whether the planning architecture remains appropriate after autonomous participants respond and physics constrains the outcome. We introduce a controlled, physics-grounded benchmark built around planning-induced control trajectories: the ordered planning operations and directives through which an execution architecture acts on other agents and the physical process. It implements predefined, sequential, hierarchical, and search executors in a smart-grid demand-response system with 40 heterogeneous prosumers and an independently simulated radial feeder. The LLM is bounded to typed policy declaration and short operator messages, while schedule construction, prosumer dynamics, and power flow remain explicit code. The protocol uses paired forced-mode counterfactuals, common random response draws, and event-level deadline feasibility. Three properties follow. Architecture materially changes outcomes: forced search is the oracle in all five baseline seeds. Execution fidelity needs more than mode agreement: objective substitution holds agreement at 1.0 while increasing voltage shortfall by 2.68x. A 144-scenario, 576-episode bank has feasible oracles from three of the four architectures. A prespecified stress-held-out ridge has mean regret 90.7 (95% interval [73.8, 108.6]) and no detectable value over fixed sequential; applying known deadline feasibility before quality prediction cuts regret to 29.0 and improves over fixed sequential by 61.1. An all-feasible ablation does not beat fixed search, localising the remaining challenge to within-feasible quality selection. A five-model extension separates stress-conditioned, state-blind, and invariant declarers; latency tails show that live feasibility should be treated probabilistically.

Recent advancements in video generation have witnessed significant progress, especially with the rapid advancement of diffusion models. Despite this, their deficiencies in physical cognition have gradually received widespread attention - generated content often violates the fundamental laws of physics, falling into the dilemma of ''visual realism but physical absurdity". Researchers began to increasingly recognize the importance of physical fidelity in video generation and attempted to integrate heuristic physical cognition such as motion representations and physical knowledge into generative systems to simulate real-world dynamic scenarios. Considering the lack of a systematic overview in this field, this survey aims to provide a comprehensive summary of architecture designs and their applications to fill this gap. Specifically, we discuss and organize the evolutionary process of physical cognition in video generation from a cognitive science perspective, while proposing a three-tier taxonomy: 1) basic schema perception for generation, 2) passive cognition of physical knowledge for generation, and 3) active cognition for world simulation, encompassing state-of-the-art methods, classical paradigms, and benchmarks. Subsequently, we emphasize the inherent key challenges in this domain and delineate potential pathways for future research, contributing to advancing the frontiers of discussion in both academia and industry. Through structured review and interdisciplinary analysis, this survey aims to provide directional guidance for developing interpretable, controllable, and physically consistent video generation paradigms, thereby propelling generative models from the stage of ''visual mimicry'' towards a new phase of ''human-like physical comprehension''.

Instruction-based image editing has achieved remarkable success in semantic alignment, yet state-of-the-art models frequently fail to render physically plausible results when editing involves complex causal dynamics, such as refraction or material deformation. We attribute this limitation to the dominant paradigm that treats editing as a discrete mapping between image pairs, which provides only boundary conditions and leaves transition dynamics underspecified. To address this, we reformulate physics-aware editing as predictive physical state transitions and introduce PhysicTran38K, a large-scale video-based dataset comprising 38K transition trajectories across five physical domains, constructed via a two-stage filtering and constraint-aware annotation pipeline. Building on this supervision, we propose PhysicEdit, an end-to-end framework equipped with a textual-visual dual-thinking mechanism. It combines a frozen Qwen2.5-VL for physically grounded reasoning with learnable transition queries that provide timestep-adaptive visual guidance to a diffusion backbone. Experiments show that PhysicEdit improves over Qwen-Image-Edit by 5.9% in physical realism and 10.1% in knowledge-grounded editing, setting a new state-of-the-art for open-source methods, while remaining competitive with leading proprietary models.

Understanding the physical structure is essential for real-world applications such as embodied agents, interactive design, and long-horizon manipulation. Yet, prevailing Vision-Language Model (VLM) evaluations still center on structure-agnostic, single-turn setups (e.g., VQA), which fail to assess agents' ability to reason about how geometry, contact, and support relations jointly constrain what actions are possible in a dynamic environment. To address this gap, we introduce the Causal Hierarchy of Actions and Interactions (CHAIN) benchmark, an interactive 3D, physics-driven testbed designed to evaluate whether models can understand, plan, and execute structured action sequences grounded in physical constraints. CHAIN shifts evaluation from passive perception to active problem solving, spanning tasks such as interlocking mechanical puzzles and 3D stacking and packing. We conduct a comprehensive study of state-of-the-art VLMs and diffusion-based models under unified interactive settings. Our results show that top-performing models still struggle to internalize physical structure and causal constraints, often failing to produce reliable long-horizon plans and cannot robustly translate perceived structure into effective actions. The project is available at https://social-ai-studio.github.io/CHAIN/.

Deformable object manipulation poses challenges beyond task completion: successful execution must also maintain safe physical interaction, holding the object stably without slip or drop while avoiding excessive deformation. However, existing manipulation benchmarks are predominantly success-oriented and rarely evaluate whether a policy remains physically safe throughout execution. We present SoftVTBench, a safety-aware visuo-tactile benchmark for physically constrained deformable object manipulation. Built in Isaac Sim with finite-element-simulated deformable objects, SoftVTBench provides multi-view RGB observations, RGB tactile sensing with marker motion, proprioception, and language instructions, and defines four matched task suites over object type (deformable vs. rigid) and variation axis (object vs. spatial). It separately reports Goal Success and Safety Success; the latter additionally requires no drop and peak deformation below a calibrated object-specific threshold, measured from policy-hidden privileged Finite Element Method (FEM) states. We implement pi0.5-based baselines under this protocol. Experiments show that success-only evaluation substantially overstates policy performance, as a large fraction of goal-completing rollouts still violate physical safety. Furthermore, incorporating tactile sensing improves Safety Success (e.g., from 21.4% to 35.6% on object-centric deformable tasks) and reduces object deformation during execution, while maintaining comparable Goal Success. SoftVTBench provides a reproducible benchmark for studying visuo-tactile deformable manipulation under physical interaction constraints.

Video editing has advanced substantially in recent years, with methods increasingly accounting for the visual consequences of edits, such as changes to shadows and occlusions. However, the physical consequences of edits, including changes to subsequent motion and interactions, remain less explored. We formulate this problem as physical counterfactual video editing (PCVE), which aims to generate a counterfactual video depicting the resulting motion and interactions given a source video, a physical edit, and its execution frame. PCVE is challenging because it requires understanding scene physics and inferring the downstream motion and interactions induced by a physical intervention, while paired factual and counterfactual data and dedicated evaluation metrics are lacking. We introduce VideoPhysEdit, a new training-free pipeline for PCVE in rigid-body scenes. It makes physical reasoning explicit through a novel physical scene reconstruction method that recovers a scene reproducing the observed motion and interactions under simulation, enabling the pipeline to apply physical edits as interventions and use the resulting trajectories to guide counterfactual video generation. We further construct PCVE-RigidBench, a synthetic benchmark with paired source and counterfactual target videos and physical ground truth, and introduce the Physical Edit Score. VideoPhysEdit achieves substantially higher physical edit accuracy than open-source methods and commercial models while maintaining competitive visual fidelity. Its Physical Edit Score is 0.376, the only positive score among the compared methods. Qualitative comparisons on real videos further show that VideoPhysEdit applies to real-world scenes and better depicts the downstream motion and interactions induced by the edits than the compared methods. Code: https://github.com/Hammour-steak/VideoPhysEdit

Vision-language-action (VLA) and world-action (WAM) models map observations and instructions directly to robot actions. This directness ties a policy to training: minor layout or viewpoint changes cause failure, and instructions generalize poorly. The root cause lies in representation: task requirements, conditions, progress, and failure recovery are implicitly encoded in action sequences, making them difficult to inspect or revise. Digital coding agents offer a precedent: LLMs call tools, verify results, and revise from feedback as executable code. The same working pattern of explicit state, manageable execution, and revisable procedures underlies generalization and long-horizon execution in the physical world, letting physical experience return as reusable programs, memory, or evidence. We propose Physical Coding, representing task state and execution as code. Code as World records objects, relations, constraints, and progress; Code as Policy organizes planning, verification, recovery, and execution. We build HexaAnything, which calls perception, planning, and control tools, including VLA/WAM policies, and makes in-the-loop decisions from external feedback. Verified traces become data and memory, enabling evolution from tools and Harness to model weights, architectures, and ultimately hardware and task design. On RoboCasa365, HexaAnything improves Composite-Unseen and overall success over XR-1 VLA, and its Harness-trained HexaModel beats the base on every split, indicating code traces internalize physical execution. On PhyBench and a dual-arm AgileX robot, the agent autonomously completes physics experiments and most tabletop tasks, often faster than published results. We observe data, model, and tool self-evolution; future work targets weight internalization, autonomous redesign of architectures, languages, representations, and tasks, and deployment in manufacturing and science.

Placement is crucial in the physical design, as it greatly affects power, performance, and area metrics. Recent advancements in analytical methods, such as DREAMPlace, have demonstrated impressive performance in global placement. However, DREAMPlace has some limitations, e.g., may not guarantee legalizable placements under the same settings, leading to fragile and unpredictable results. This paper highlights the main issue as being stuck in local optima, and proposes a hybrid optimization framework to efficiently escape the local optima, by perturbing the placement result iteratively. The proposed framework achieves significant improvements compared to state-of-the-art methods on two popular benchmarks.

Physical AI systems increasingly map multimodal observations, language instructions, and learned world representations into physically consequential actions. Robotics foundation models, vision-language-action models, and world-model-based autonomous systems can condition decisions that move vehicles, robots, drones, and industrial machines. This transition exposes a safety problem that is not fully captured by conventional AI content moderation or by classical robot safety alone: a black-box model may issue a physically consequential action while appearing confident, plausible, and semantically aligned. The resulting failure can be silent, arising from sensor drift, occlusion, state-estimation error, distribution shift, hallucinated affordances, or invalid physical assumptions before downstream hardware controllers detect a violation. Across embodied foundation models, world models, robotics simulation, embodied safety benchmarks, safe control, runtime assurance, uncertainty estimation, verification, and guardrail evaluation, model capability and safety mechanisms have advanced along largely separate technical tracks. A recurring gap synthesized here is that no single stream surveyed in this review supplies a complete runtime authorization boundary between black-box Physical AI models and physical execution. The resulting analysis develops a bounded problem formulation, a definition of silent physical-action failure, a taxonomy of runtime guardrail functions, and evaluation requirements for comparing guardrails as Physical AI assurance mechanisms.

Vision-language-action models, world models, and agentic planners each advance physical intelligence, yet their composition lacks a common execution abstraction, shared state, semantic verification, and persistent experience across heterogeneous embodiments. We present PhyAgentOS, a runtime foundation delivering scheduling, verification, memory, benchmarking, and safety as system-level services. Its Session-Centered Runtime treats a session, not an action, as the minimum unit of scheduling, compatibility preflight, supervised execution, evidence collection, and acceptance. To decouple cognition from physical execution, the cognition-physics boundary is a file system: the State-as-a-File protocol materializes cross-layer state as Markdown with YAML, yielding inspectable, versionable records without code dependencies between Agent and Runtime layers. These views form a unified cognitive state space aligning intent, capabilities, environment, execution, and experience. The SessionVerifier distinguishes execution termination from semantic task completion via evidence-grounded verdicts of success, failure, or replan. Verified outcomes are consolidated through epistemic memory into reusable knowledge and corrective lessons, closing a trial-and-error loop without retraining. Benchmarking reuses the deployment session and verification path, so results trace to real execution. Layered safety constrains both policy-driven and agent-driven execution: preflight, action bridges, SafetyGuard, heartbeat monitoring, and target-local constraints. Validation is progressive: games test cognitive planning, simulation adds dynamics and control, real robots add hardware noise, with the cognitive layer held constant. PhyAgentOS is benchmarked on Optimus-67, StarDojo, and DST-Dojo, validated on 19+ simulated and physical embodiments, and gains on LIBERO, Calvin, and RoboCasa365 across multiple VLA models.

3D modeling is moving from virtual to physical. Existing 3D generation primarily emphasizes geometries and textures while neglecting physical-grounded modeling. Consequently, despite the rapid development of 3D generative models, the synthesized 3D assets often overlook rich and important physical properties, hampering their real-world application in physical domains like simulation and embodied AI. As an initial attempt to address this challenge, we propose PhysX, an end-to-end paradigm for physical-grounded 3D asset generation. 1) To bridge the critical gap in physics-annotated 3D datasets, we present PhysXNet - the first physics-grounded 3D dataset systematically annotated across five foundational dimensions: absolute scale, material, affordance, kinematics, and function description. In particular, we devise a scalable human-in-the-loop annotation pipeline based on vision-language models, which enables efficient creation of physics-first assets from raw 3D assets.2) Furthermore, we propose PhysXGen, a feed-forward framework for physics-grounded image-to-3D asset generation, injecting physical knowledge into the pre-trained 3D structural space. Specifically, PhysXGen employs a dual-branch architecture to explicitly model the latent correlations between 3D structures and physical properties, thereby producing 3D assets with plausible physical predictions while preserving the native geometry quality. Extensive experiments validate the superior performance and promising generalization capability of our framework. All the code, data, and models will be released to facilitate future research in generative physical AI.

The image-to-image translation abilities of generative learning models have recently made significant progress in the estimation of complex (steered) mappings between image distributions. While appearance based tasks like image in-painting or style transfer have been studied at length, we propose to investigate the potential of generative models in the context of physical simulations. Providing a dataset of 300k image-pairs and baseline evaluations for three different physical simulation tasks, we propose a benchmark to investigate the following research questions: i) are generative models able to learn complex physical relations from input-output image pairs? ii) what speedups can be achieved by replacing differential equation based simulations? While baseline evaluations of different current models show the potential for high speedups (ii), these results also show strong limitations toward the physical correctness (i). This underlines the need for new methods to enforce physical correctness. Data, baseline models and evaluation code http://www.physics-gen.org.

Physical fidelity has received increasing attention in world models and video generation, yet how video representations encode physical information remains less understood. We introduce the World Embedding Benchmark, comprising 8,000 controlled simulation cases from 80 families spanning fluid mechanics, solid mechanics, dynamics, and optics & electromagnetism. Each case pairs a rendered video with simulation-derived physical annotations, supporting three complementary tasks: text-video retrieval, physical-property regression, and multiple-choice video-description pair classification. We use these tasks to distinguish cross-modal physical alignment from the recoverability of quantitative physical information. Evaluated pre-trained omnimodal embedding models show weak retrieval and near-chance within-family pair classification, while lightweight probes recover useful physical information from frozen video embeddings. Continual contrastive training with physics-specific video-text pairs improves retrieval and pair classification but degrades physical-property regression, revealing a trade-off between alignment and quantitative information recoverability. Finally, we use the embeddings to retrieve reference videos for retrieval-augmented generation with MiniMax-H3. Retrieved references improve the physical fidelity of generated videos, with stronger retrieval models yielding larger gains in our experiments. Together, these findings highlight the need to evaluate physical alignment and property recoverability jointly, and demonstrate the utility of physical representations for improving video generation.

Physical principles are fundamental to realistic visual simulation, but remain a significant oversight in transformer-based video generation. This gap highlights a critical limitation in rendering rigid body motion, a core tenet of classical mechanics. While computer graphics and physics-based simulators can easily model such collisions using Newton formulas, modern pretrain-finetune paradigms discard the concept of object rigidity during pixel-level global denoising. Even perfectly correct mathematical constraints are treated as suboptimal solutions (i.e., conditions) during model optimization in post-training, fundamentally limiting the physical realism of generated videos. Motivated by these considerations, we introduce, for the first time, a physics-aware reinforcement learning paradigm for video generation models that enforces physical collision rules directly in high-dimensional spaces, ensuring the physics knowledge is strictly applied rather than treated as conditions. Subsequently, we extend this paradigm to a unified framework, termed Mimicry-Discovery Cycle (MDcycle), which allows substantial fine-tuning while fully preserving the model's ability to leverage physics-grounded feedback. To validate our approach, we construct new benchmark PhysRVGBench and perform extensive qualitative and quantitative experiments to thoroughly assess its effectiveness.

We present PhysGen, a novel image-to-video generation method that converts a single image and an input condition (e.g., force and torque applied to an object in the image) to produce a realistic, physically plausible, and temporally consistent video. Our key insight is to integrate model-based physical simulation with a data-driven video generation process, enabling plausible image-space dynamics. At the heart of our system are three core components: (i) an image understanding module that effectively captures the geometry, materials, and physical parameters of the image; (ii) an image-space dynamics simulation model that utilizes rigid-body physics and inferred parameters to simulate realistic behaviors; and (iii) an image-based rendering and refinement module that leverages generative video diffusion to produce realistic video footage featuring the simulated motion. The resulting videos are realistic in both physics and appearance and are even precisely controllable, showcasing superior results over existing data-driven image-to-video generation works through quantitative comparison and comprehensive user study. PhysGen's resulting videos can be used for various downstream applications, such as turning an image into a realistic animation or allowing users to interact with the image and create various dynamics. Project page: https://stevenlsw.github.io/physgen/

AI video generation is undergoing a revolution, with quality and realism advancing rapidly. These advances have led to a passionate scientific debate: Do video models learn ``world models'' that discover laws of physics -- or, alternatively, are they merely sophisticated pixel predictors that achieve visual realism without understanding the physical principles of reality? We address this question by developing Physics-IQ, a comprehensive benchmark dataset that can only be solved by acquiring a deep understanding of various physical principles, like fluid dynamics, optics, solid mechanics, magnetism and thermodynamics. We find that across a range of current models (Sora, Runway, Pika, Lumiere, Stable Video Diffusion, and VideoPoet), physical understanding is severely limited, and unrelated to visual realism. At the same time, some test cases can already be successfully solved. This indicates that acquiring certain physical principles from observation alone may be possible, but significant challenges remain. While we expect rapid advances ahead, our work demonstrates that visual realism does not imply physical understanding. Our project page is at https://physics-iq.github.io; code at https://github.com/google-deepmind/physics-IQ-benchmark.

While generative models have become effective at producing human-like motions from text, transferring these motions to humanoid robots for physical execution remains challenging. Existing pipelines are often limited by retargeting, where kinematic quality is undermined by physical infeasibility, contact-transition errors, and the high cost of real-world dynamical data. We present a unified latent-driven framework that bridges natural language and whole-body humanoid locomotion through a retarget-free, physics-optimized pipeline. Rather than treating generation and control as separate stages, our key insight is to couple them bidirectionally under physical constraints.We introduce a Physical Plausibility Optimization (PP-Opt) module as the coupling interface. In the forward direction, PP-Opt refines a teacher-student distillation policy with a plausibility-centric reward to suppress artifacts such as floating, skating, and penetration. In the backward direction, it converts reward-optimized simulation rollouts into high-quality explicit motion data, which is used to fine-tune the motion generator toward a more physically plausible latent distribution. This bidirectional design forms a self-improving cycle: the generator learns a physically grounded latent space, while the controller learns to execute latent-conditioned behaviors with dynamical integrity.Extensive experiments on the Unitree G1 humanoid show that our bidirectional optimization improves tracking accuracy and success rates. Across IsaacLab and MuJoCo, the implicit latent-driven pipeline consistently outperforms conventional explicit retargeting baselines in both precision and stability. By coupling diffusion-based motion generation with physical plausibility optimization, our framework provides a practical path toward deployable text-guided humanoid intelligence.

Aside from the capability of additive manufacturing (AM) methods in fabricating components with complex geometries, two crucial potentials of this manufacturing process that are worth mentioning are its flexibility in being combined with other production methods as well as use of a variety of materials in a single production platform to make multi-material and composite products. Implementation of multiple materials in integrated structures has been shown to improve the functionality, weight reduction and, by merging the assembly and production into one stage, modify the manufacturing processes. Different approaches towards modification of AM processes aimed to reach multi-material or composite parts are being reviewed in this paper.

Developing physically aware video generation models remains a significant challenge due to the difficulty in capturing diverse physical phenomena, such as thermal dynamics, mechanics, and optics. In this work, we introduce PhysRAG, a novel pipeline that enhances physical awareness in video generation through Retrieval-Augmented Generation (RAG). To address the issue of limited high-quality data, we design a two-stage data filtering pipeline based on the WISA-80K dataset, resulting in a curated set of 7K high-quality videos for training. Furthermore, we construct a physical video database and develop a mechanism to inject physical knowledge into a video diffusion model using learnable queries. Our method achieves state-of-the-art performance in both visual quality and physical rule compliance, surpassing existing models in benchmarks such as PhyGenBench and VBench. We conduct extensive ablation studies to validate the effectiveness of our key components, including the data filtering pipeline, RAG mechanism, and method for physical information extraction. To facilitate future research, our code, data, and models are prepared for release at https://github.com/sediment1024/PhysRAG.

Structural modeling is a fundamental component of computational engineering science, in which even minor physical inconsistencies or specification violations may invalidate downstream simulations. The potential of large language models (LLMs) for automatic generation of modeling code has been demonstrated. However, non-executable or physically inconsistent outputs remain prevalent under stringent engineering constraints. A framework for physics-consistent automatic building modeling is therefore proposed, integrating domain knowledge construction, constraint-oriented model alignment, and verification-driven evaluation. CivilInstruct is introduced as a domain-specific dataset that formalizes structural engineering knowledge and constraint reasoning to enable simulation-ready model generation. A two-stage fine-tuning strategy is further employed to enforce constraint satisfaction and application programming interface compliance, substantially reducing hallucinated and non-conforming outputs. MBEval is presented as a verification-driven benchmark that evaluates executability and structural dynamics consistency through closed-loop validation. Experimental results show consistent improvements over baselines across rigorous verification metrics. Our code is available at https://github.com/Jovanqing/AutoBM.

The scalability of humanoid robots will depend not only on models and hardware, but also on whether physical experience can accumulate across robots, tasks, organizations, and time. Drawing on the authors' work in developing ISO/WD 26264-1, Humanoid robot datasets -- Part 1: General requirements, within ISO/TC 299/WG 16, this article argues that data standards are becoming foundational infrastructure for Physical AI. We develop three insights. First, humanoid robot data is embodied interaction data, not a collection of isolated digital samples; a useful dataset must preserve the relationship among robot body, action, task, scene, execution trace, and outcome. Second, its value depends on physical coherence: multimodal streams are reusable only when timing, coordinate frames, calibration, kinematics, units, and synchronization assumptions remain inspectable. Third, the main bottleneck is not only data scarcity, but non-cumulative data caused by high collection costs, data silos, and inconsistent evaluation. We argue that humanoid robot data standards address these bottlenecks by making embodied experience interpretable, shareable, traceable, and reusable. A general standard should provide horizontal infrastructure for lifecycle management, metadata, provenance, quality, versioning, and traceability, while capability-specific parts should define domain grammar for manipulation, locomotion, human-robot interaction, cognition, and future humanoid capabilities. As AI moves from screens into bodies, data standards must evolve from organizing digital information to structuring physical interaction.

Large Language Models (LLMs) can generate Computer-Aided Design (CAD), yet lack physical comprehension required for reliable engineering design. Instead of attempting to implicitly learn physical laws from data, we propose a Hybrid Agentic-Physical Architecture that embeds validated knowledge-based engineering tools directly into the decision making loop of autonomous AI agents. In this framework, engineering design is formulated as a closed-loop, sequential decision making process guided by explicit physical verification. Based on a load case, dedicated agents iteratively plan, generate, evaluate, and revise engineering designs using knowledge-based tools as a feedback signal. We introduce a benchmark dataset and metrics for assessing functional validity in generative CAD. Our system generates more complex and physically verified designs, with a 4.2 increase in structural complexity and improving compile rate by 3.5% compared to similar agentic methods. The codebase, prompts and dataset will be made publicly available to support reproducibility and future research.

Video generation models have made impressive strides in synthesizing visually compelling content, yet their outputs remain confined to the virtual domain. A natural question follows: how well do these models reflect the physical world when their generated videos leave the screen and enter reality? We propose robotic manipulation as a concrete, measurable window onto this question: if a model has truly internalized physical laws, the motion it depicts should translate into executable robot behavior. We introduce Dream.exe, an evaluation framework that operationalizes this criterion through a video-to-execution pipeline. Given a scene image and a task description, Dream.exe synthesizes a manipulation video, converts the generated motion into robot trajectories, and executes them in a physics simulator, yielding a grounding signal that purely visual metrics cannot offer. Using this pipeline, we evaluate 8 models spanning frontier closed-source generators, open-source generators, and robot-specific models. Our benchmark covers 101 manually curated manipulation tasks at three levels of physical complexity, measured across visual quality, trajectory fidelity, and execution success. Encouragingly, several models achieve measurable execution success, suggesting that generative priors learned from internet-scale data already encode meaningful physical knowledge. Yet visual quality proves a poor predictor of executability, exposing a dimension of model capability that standard visual evaluations do not capture. Dream.exe will be open-sourced at https://github.com/showlab/Dream.exe.

Physical intelligence holds immense promise for advancing embodied intelligence, enabling robots to acquire complex behaviors from demonstrations. However, achieving generalization and transfer across diverse robotic platforms and environments requires careful design of model architectures, training strategies, and data diversity. Meanwhile existing systems often struggle with scalability, adaptability to heterogeneous hardware, and objective evaluation in real-world settings. We present a generalized end-to-end robotic learning framework designed to bridge this gap. Our framework introduces a unified architecture that supports cross-platform adaptability, enabling seamless deployment across industrial-grade robots, collaborative arms, and novel embodiments without task-specific modifications. By integrating multi-task learning with streamlined network designs, it achieves more robust performance than conventional approaches, while maintaining compatibility with varying sensor configurations and action spaces. We validate our framework through extensive experiments on seven manipulation tasks. Notably, Diffusion-based models trained in our framework demonstrated superior performance and generalizability compared to the LeRobot framework, achieving performance improvements across diverse robotic platforms and environmental conditions.

Reviewing the progress in artificial intelligence over the past decade, various significant advances (e.g. object detection, image generation, large language models) have enabled AI systems to produce more semantically meaningful outputs and achieve widespread adoption in internet scenarios. Nevertheless, AI systems still struggle when it comes to understanding and interacting with the physical world. This reveals an important issue: relying solely on semantic-level concepts learned from internet data (e.g. texts, images) to understand the physical world is far from sufficient -- machine intelligence currently lacks an effective way to learn about the physical world. This research introduces the idea of analytic concept -- representing the concepts related to the physical world through programs of mathematical procedures, providing machine intelligence a portal to perceive, reason about, and interact with the physical world. Except for detailing the design philosophy and providing guidelines for the application of analytic concepts, this research also introduce about the infrastructure that has been built around analytic concepts. I aim for my research to contribute to addressing these questions: What is a proper abstraction of general concepts in the physical world for machine intelligence? How to systematically integrate structured priors with neural networks to constrain AI systems to comply with physical laws?

Physical AI requires models to ground visual and linguistic understanding in real-world environments while accounting for environmental constraints and execution feedback. We introduce MachEmbodied-VLM (ME-VLM), a unified vision-language model with two variants, 4B and 35B-A3B, that brings together embodied cognition and multimodal agent capabilities. Our work emphasizes physical perception and spatiotemporal reasoning, together with planning, interaction, and outcome assessment in both digital and physical environments. We construct training data spanning embodied and multimodal agent tasks, including execution observations and feedback to support outcome assessment and decision refinement. The training pipeline comprises embodied capability injection, separate reinforcement learning of embodied and multimodal-agent experts, and multi-teacher on-policy distillation that consolidates their complementary capabilities into a single model. Experiments show competitive performance on both embodied and agent benchmarks, as well as on autonomous-driving and embodied-navigation tasks. For edge deployment, visual token compression, W4A8 quantization, and hardware-software co-optimization enable on-device inference of the 4B variant on the M100, reducing prefill latency from 400 ms to 188 ms. Project Page: https://machembodied.com/ME-Brain/ME-VLM.html Code Repository: https://github.com/MachEmbodied/ME-VLM

We introduce PhysicalAgent, an agentic framework for robotic manipulation that integrates iterative reasoning, diffusion-based video generation, and closed-loop execution. Given a textual instruction, our method generates short video demonstrations of candidate trajectories, executes them on the robot, and iteratively re-plans in response to failures. This approach enables robust recovery from execution errors. We evaluate PhysicalAgent across multiple perceptual modalities (egocentric, third-person, and simulated) and robotic embodiments (bimanual UR3, Unitree G1 humanoid, simulated GR1), comparing against state-of-the-art task-specific baselines. Experiments demonstrate that our method consistently outperforms prior approaches, achieving up to 83% success on human-familiar tasks. Physical trials reveal that first-attempt success is limited (20-30%), yet iterative correction increases overall success to 80% across platforms. These results highlight the potential of video-based generative reasoning for general-purpose robotic manipulation and underscore the importance of iterative execution for recovering from initial failures. Our framework paves the way for scalable, adaptable, and robust robot control.

Reacting to sudden physical hazards (catching a slipping plate, dodging a falling knife) is both a meaningful test of embodied intelligence and a hard requirement for deploying multimodal large language models (MLLMs) as the decision coreof household robots. Existing evaluations, however, probe intuitive physics passively through question answering over videos, or target deliberate, long-horizon tasks such as navigation and rearrangement; none measure whether a model can turn physical understanding into immediate, safety-critical action. We introduce ReactHuman, the first physics-grounded benchmark for human-like reactive decision-making, in which the evaluated MLLM acts as the brain of a simulated humanoid facing sudden household hazards; it spans 17 event families and over 1,000 bit-for-bit reproducible scenes with exact, annotation-free ground truth derived from 240 Hz rigid-body simulation, including adversarial objects whose appearance contradicts their physics (a foam anvil, a steel apple). We further design a five-metric suite that scores each reaction along three axes: reasonable, safe, and physically grounded. We physically execute every committed plan so that decisions have observable consequences. With this harness we evaluate seven representative MLLMs. Results show that reactive safety is far from solved: models mishandle roughly one hazard in three, act from fixed dispositions rather than the observed scene, trust appearance over motion, and miss interception points at meter scale even when the chosen action is correct; none of these failures shrink with model scale. ReactHuman thus offers both a fine-grained diagnosis and a scalable training signal toward physically grounded, safety-aware embodied agents. The benchmark can be found here: https://huggingface.co/datasets/Alan123/reacthuman-benchmark-scaled

Physical understanding remains brittle in omni-modal models because key physical attributes are visually ambiguous and sparsely represented in web-scale data. We present OmniFysics, a compact omni-modal model that unifies understanding across images, audio, video, and text, with integrated speech and image generation. To inject explicit physical knowledge, we build a physical data engine with two components. FysicsAny produces physics-grounded instruction--image supervision by mapping salient objects to verified physical attributes through hierarchical retrieval over a curated prototype database, followed by physics-law--constrained verification and caption rewriting. FysicsOmniCap distills web videos via audio--visual consistency filtering to generate high-fidelity video--instruction pairs emphasizing cross-modal physical cues. We train OmniFysics with staged multimodal alignment and instruction tuning, adopt latent-space flow matching for text-to-image generation, and use an intent router to activate generation only when needed. Experiments show competitive performance on standard multimodal benchmarks and improved results on physics-oriented evaluations.

Text-to-image generation has reached photorealistic quality, yet state-of-the-art systems remain unreliable at producing scientific diagrams, whose value depends not on appearance but on physical faithfulness: correct force directions, valid coordinate systems, consistent thermodynamic states, and equations matching the depicted scenario. Trained on web imagery with physically shallow captions, generic models produce diagrams that look plausible but are physically wrong, harmful in education and scientific communication. We present Princigram, a physics-faithful scientific-diagram generator, and its data pipeline. Our central advance is Structured Physical Chain-of-Thought (SP-CoT): a per-subdiscipline schema that decomposes a physics diagram into an explicit multi-step reasoning chain across six subdisciplines, from scene identification through force or process analysis to governing laws and synthesis. Unlike free-form chain-of-thought, SP-CoT follows a fixed schema with strict fidelity rules that separate visually grounded facts from physically inferred reasoning and type all mathematics symbolically; it serves both as dense training supervision and, at inference, as a structured "thinking" prompt. With it we curate and structurally annotate 4.3 million physics images, of which 115,037 carry expert-level annotation, and adapt a unified multimodal backbone. We further introduce VeriphyT2IBench, whose questions are derived from each held-out diagram's own structured annotation: each diagram becomes an item-specific bank of binary questions about its objects, forces, and states, so a judge model's score decomposes into named physical facts rather than one holistic number. On the physics subset of GenExam and on VeriphyT2IBench, Princigram shows that explicit physics-structured supervision improves the physical faithfulness of generated scientific diagrams.

Traditional foundation models are pre-trained on broad datasets to reduce the training resources (e.g., time, energy, labeled samples) needed for fine-tuning a wide range of downstream tasks. However, traditional foundation models struggle with out-of-distribution prediction and can produce outputs that are unrealistic and physically infeasible. We propose the notation of physics-guided foundation models (PGFM), that is, foundation models integrated with broad or general domain (e.g., scientific) physical knowledge applicable to a wide range of downstream tasks.

Our interest is in the design of software systems involving a human-expert interacting -- using natural language -- with a large language model (LLM) on data analysis tasks. For complex problems, it is possible that LLMs can harness human expertise and creativity to find solutions that were otherwise elusive. On one level, this interaction takes place through multiple turns of prompts from the human and responses from the LLM. Here we investigate a more structured approach based on an abstract protocol described in [3] for interaction between agents. The protocol is motivated by a notion of "two-way intelligibility" and is modelled by a pair of communicating finite-state machines. We provide an implementation of the protocol, and provide empirical evidence of using the implementation to mediate interactions between an LLM and a human-agent in two areas of scientific interest (radiology and drug design). We conduct controlled experiments with a human proxy (a database), and uncontrolled experiments with human subjects. The results provide evidence in support of the protocol's capability of capturing one- and two-way intelligibility in human-LLM interaction; and for the utility of two-way intelligibility in the design of human-machine systems. Our code is available at https://github.com/karannb/interact.

Digital twins, as precise digital representations of physical systems, have evolved from passive simulation tools into intelligent and autonomous entities through the integration of artificial intelligence technologies. This paper presents a unified four-stage framework that systematically characterizes AI integration across the digital twin lifecycle, spanning modeling, mirroring, intervention, and autonomous management. By synthesizing existing technologies and practices, we distill a unified four-stage framework that systematically characterizes how AI methodologies are embedded across the digital twin lifecycle: (1) modeling the physical twin through physics-based and physics-informed AI approaches, (2) mirroring the physical system into a digital twin with real-time synchronization, (3) intervening in the physical twin through predictive modeling, anomaly detection, and optimization strategies, and (4) achieving autonomous management through large language models, foundation models, and intelligent agents. We analyze the synergy between physics-based modeling and data-driven learning, highlighting the shift from traditional numerical solvers to physics-informed and foundation models for physical systems. Furthermore, we examine how generative AI technologies, including large language models and generative world models, transform digital twins into proactive and self-improving cognitive systems capable of reasoning, communication, and creative scenario generation. Through a cross-domain review spanning eleven application domains, including healthcare, aerospace, smart manufacturing, robotics, and smart cities, we identify common challenges related to scalability, explainability, and trustworthiness, and outline directions for responsible AI-driven digital twin systems.

Human motion capture from monocular videos has made significant progress in recent years. However, modern approaches often produce temporal artifacts, e.g. in form of jittery motion and struggle to achieve smooth and physically plausible motions. Explicitly integrating physics, in form of internal forces and exterior torques, helps alleviating these artifacts. Current state-of-the-art approaches make use of an automatic PD controller to predict torques and reaction forces in order to re-simulate the input kinematics, i.e. the joint angles of a predefined skeleton. However, due to imperfect physical models, these methods often require simplifying assumptions and extensive preprocessing of the input kinematics to achieve good performance. To this end, we propose a novel method to selectively incorporate the physics models with the kinematics observations in an online setting, inspired by a neural Kalman-filtering approach. We develop a control loop as a meta-PD controller to predict internal joint torques and external reaction forces, followed by a physics-based motion simulation. A recurrent neural network is introduced to realize a Kalman filter that attentively balances the kinematics input and simulated motion, resulting in an optimal-state dynamics prediction. We show that this filtering step is crucial to provide an online supervision that helps balancing the shortcoming of the respective input motions, thus being important for not only capturing accurate global motion trajectories but also producing physically plausible human poses. The proposed approach excels in the physics-based human pose estimation task and demonstrates the physical plausibility of the predictive dynamics, compared to state of the art. The code is available on https://github.com/cuongle1206/OSDCap

Video generation models nowadays are capable of generating visually realistic videos, but often fail to adhere to physical laws, limiting their ability to generate physically plausible videos and serve as ''world models''. To address this issue, we propose PhysMaster, which captures physical knowledge as a representation for guiding video generation models to enhance their physics-awareness. Specifically, PhysMaster is based on the image-to-video task where the model is expected to predict physically plausible dynamics from the input image. Since the input image provides physical priors like relative positions and potential interactions of objects in the scenario, we devise PhysEncoder to encode physical information from it as an extra condition to inject physical knowledge into the video generation process. The lack of proper supervision on the model's physical performance beyond mere appearance motivates PhysEncoder to apply reinforcement learning with human feedback to physical representation learning, which leverages feedback from generation models to optimize physical representations with Direct Preference Optimization (DPO) in an end-to-end manner. PhysMaster provides a feasible solution for improving physics-awareness of PhysEncoder and thus of video generation, proving its ability on a simple proxy task and generalizability to wide-ranging physical scenarios. This implies that our PhysMaster, which unifies solutions for various physical processes via representation learning in the reinforcement learning paradigm, can act as a generic and plug-in solution for physics-aware video generation and broader applications.

The robot learning community has made great strides in recent years, proposing new architectures and showcasing impressive new capabilities; however, the dominant metric used in the literature, especially for physical experiments, is "success rate", i.e. the percentage of runs that were successful. Furthermore, it is common for papers to report this number with little to no information regarding the number of runs, the initial conditions, and the success criteria, little to no narrative description of the behaviors and failures observed, and little to no statistical analysis of the findings. In this paper we argue that to move the field forward, researchers should provide a nuanced evaluation of their methods, especially when evaluating and comparing learned policies on physical robots. To do so, we propose best practices for future evaluations: explicitly reporting the experimental conditions, evaluating several metrics designed to complement success rate, conducting statistical analysis, and adding a qualitative description of failures modes. We illustrate these through an evaluation on physical robots of several learned policies for manipulation tasks.

Recent advances in real-time interactive text-driven motion generation have enabled humanoids to perform diverse behaviors. However, kinematics-only generators often exhibit physical hallucinations, producing motion trajectories that are physically infeasible to track with a downstream motion tracking controller or unsafe for real-world deployment. These failures often arise from the lack of explicit physics-aware objectives for real-robot execution and become more severe under out-of-distribution (OOD) user inputs. Hence, we propose SafeFlow, a text-driven humanoid whole-body control framework that combines physics-guided motion generation with a 3-Stage Safety Gate driven by explicit risk indicators. SafeFlow adopts a two-level architecture. At the high level, we generate motion trajectories using Physics-Guided Rectified Flow Matching in a VAE latent space to improve real-robot executability, and further accelerate sampling via Reflow to reduce the number of function evaluations (NFE) for real-time control. The 3-Stage Safety Gate enables selective execution by detecting semantic OOD prompts using a Mahalanobis score in text-embedding space, filtering unstable generations via a directional sensitivity discrepancy metric, and enforcing final hard kinematic constraints such as joint and velocity limits before passing the generated trajectory to a low-level motion tracking controller. Extensive experiments on the Unitree G1 demonstrate that SafeFlow outperforms prior diffusion-based methods in success rate, physical compliance, and inference speed, while maintaining diverse expressiveness.

Modern video diffusion models excel at appearance synthesis but still struggle with physical consistency: objects drift, collisions lack realistic rebound, and material responses seldom match their underlying properties. We present PhyCo, a framework that introduces continuous, interpretable, and physically grounded control into video generation. Our approach integrates three key components: (i) a large-scale dataset of over 100K photorealistic simulation videos where friction, restitution, deformation, and force are systematically varied across diverse scenarios; (ii) physics-supervised fine-tuning of a pretrained diffusion model using a ControlNet conditioned on pixel-aligned physical property maps; and (iii) VLM-guided reward optimization, where a fine-tuned vision-language model evaluates generated videos with targeted physics queries and provides differentiable feedback. This combination enables a generative model to produce physically consistent and controllable outputs through variations in physical attributes-without any simulator or geometry reconstruction at inference. On the Physics-IQ benchmark, PhyCo significantly improves physical realism over strong baselines, and human studies confirm clearer and more faithful control over physical attributes. Our results demonstrate a scalable path toward physically consistent, controllable generative video models that generalize beyond synthetic training environments.

Text-to-video (T2V) models like Sora have made significant strides in visualizing complex prompts, which is increasingly viewed as a promising path towards constructing the universal world simulator. Cognitive psychologists believe that the foundation for achieving this goal is the ability to understand intuitive physics. However, the capacity of these models to accurately represent intuitive physics remains largely unexplored. To bridge this gap, we introduce PhyGenBench, a comprehensive Physics Generation Benchmark designed to evaluate physical commonsense correctness in T2V generation. PhyGenBench comprises 160 carefully crafted prompts across 27 distinct physical laws, spanning four fundamental domains, which could comprehensively assesses models' understanding of physical commonsense. Alongside PhyGenBench, we propose a novel evaluation framework called PhyGenEval. This framework employs a hierarchical evaluation structure utilizing appropriate advanced vision-language models and large language models to assess physical commonsense. Through PhyGenBench and PhyGenEval, we can conduct large-scale automated assessments of T2V models' understanding of physical commonsense, which align closely with human feedback. Our evaluation results and in-depth analysis demonstrate that current models struggle to generate videos that comply with physical commonsense. Moreover, simply scaling up models or employing prompt engineering techniques is insufficient to fully address the challenges presented by PhyGenBench (e.g., dynamic scenarios). We hope this study will inspire the community to prioritize the learning of physical commonsense in these models beyond entertainment applications. We will release the data and codes at https://github.com/OpenGVLab/PhyGenBench

Understanding physical phenomena is a key competence that enables humans and animals to act and interact under uncertain perception in previously unseen environments containing novel object and their configurations. Developmental psychology has shown that such skills are acquired by infants from observations at a very early stage. In this paper, we contrast a more traditional approach of taking a model-based route with explicit 3D representations and physical simulation by an end-to-end approach that directly predicts stability and related quantities from appearance. We ask the question if and to what extent and quality such a skill can directly be acquired in a data-driven way bypassing the need for an explicit simulation. We present a learning-based approach based on simulated data that predicts stability of towers comprised of wooden blocks under different conditions and quantities related to the potential fall of the towers. The evaluation is carried out on synthetic data and compared to human judgments on the same stimuli.

Motivated by the fact that information is encoded and processed by physical systems, the P versus NP problem is examined in terms of physical processes. In particular, we consider P as a class of deterministic, and NP as nondeterministic, polynomial-time physical processes. Based on these identifications, we review a self-reference physical process in quantum theory, which belongs to NP but cannot be contained in P.

4D content generation focuses on creating dynamic 3D objects that change over time. Existing methods primarily rely on pre-trained video diffusion models, utilizing sampling processes or reference videos. However, these approaches face significant challenges. Firstly, the generated 4D content often fails to adhere to real-world physics since video diffusion models do not incorporate physical priors. Secondly, the extensive sampling process and the large number of parameters in diffusion models result in exceedingly time-consuming generation processes. To address these issues, we introduce Phy124, a novel, fast, and physics-driven method for controllable 4D content generation from a single image. Phy124 integrates physical simulation directly into the 4D generation process, ensuring that the resulting 4D content adheres to natural physical laws. Phy124 also eliminates the use of diffusion models during the 4D dynamics generation phase, significantly speeding up the process. Phy124 allows for the control of 4D dynamics, including movement speed and direction, by manipulating external forces. Extensive experiments demonstrate that Phy124 generates high-fidelity 4D content with significantly reduced inference times, achieving stateof-the-art performance. The code and generated 4D content are available at the provided link: https://anonymous.4open.science/r/BBF2/.

Denoising diffusion models hold great promise for generating diverse and realistic human motions. However, existing motion diffusion models largely disregard the laws of physics in the diffusion process and often generate physically-implausible motions with pronounced artifacts such as floating, foot sliding, and ground penetration. This seriously impacts the quality of generated motions and limits their real-world application. To address this issue, we present a novel physics-guided motion diffusion model (PhysDiff), which incorporates physical constraints into the diffusion process. Specifically, we propose a physics-based motion projection module that uses motion imitation in a physics simulator to project the denoised motion of a diffusion step to a physically-plausible motion. The projected motion is further used in the next diffusion step to guide the denoising diffusion process. Intuitively, the use of physics in our model iteratively pulls the motion toward a physically-plausible space, which cannot be achieved by simple post-processing. Experiments on large-scale human motion datasets show that our approach achieves state-of-the-art motion quality and improves physical plausibility drastically (>78% for all datasets).

Deep learning models are increasingly employed for perception, prediction, and control in complex systems. Embedding physical knowledge into these models is crucial for achieving realistic and consistent outputs, a challenge often addressed by physics-informed machine learning. However, integrating physical knowledge with representation learning becomes difficult when dealing with high-dimensional observation data, such as images, particularly under conditions of incomplete or imprecise state information. To address this, we propose Physically Interpretable World Models, a novel architecture that aligns learned latent representations with real-world physical quantities. Our method combines a variational autoencoder with a dynamical model that incorporates unknown system parameters, enabling the discovery of physically meaningful representations. By employing weak supervision with interval-based constraints, our approach eliminates the reliance on ground-truth physical annotations. Experimental results demonstrate that our method improves the quality of learned representations while achieving accurate predictions of future states, advancing the field of representation learning in dynamic systems.

Massive multiple-input multiple-output (MIMO) communication systems have a huge potential both in terms of data rate and energy efficiency, although channel estimation becomes challenging for a large number of antennas. Using a physical model allows to ease the problem by injecting a priori information based on the physics of propagation. However, such a model rests on simplifying assumptions and requires to know precisely the configuration of the system, which is unrealistic in practice.In this paper we present mpNet, an unfolded neural network specifically designed for massive MIMO channel estimation. It is trained online in an unsupervised way. Moreover, mpNet is computationally efficient and automatically adapts its depth to the signal-to-noise ratio (SNR). The method we propose adds flexibility to physical channel models by allowing a base station (BS) to automatically correct its channel estimation algorithm based on incoming data, without the need for a separate offline training phase.It is applied to realistic millimeter wave channels and shows great performance, achieving a channel estimation error almost as low as one would get with a perfectly calibrated system. It also allows incident detection and automatic correction, making the BS resilient and able to automatically adapt to changes in its environment.

While recent video generation models have achieved significant visual fidelity, they often suffer from the lack of explicit physical controllability and plausibility. To address this, some recent studies attempted to guide the video generation with physics-based rendering. However, these methods face inherent challenges in accurately modeling complex physical properties and effectively control ling the resulting physical behavior over extended temporal sequences. In this work, we introduce PhysChoreo, a novel framework that can generate videos with diverse controllability and physical realism from a single image. Our method consists of two stages: first, it estimates the static initial physical properties of all objects in the image through part-aware physical property reconstruction. Then, through temporally instructed and physically editable simulation, it synthesizes high-quality videos with rich dynamic behaviors and physical realism. Experimental results show that PhysChoreo can generate videos with rich behaviors and physical realism, outperforming state-of-the-art methods on multiple evaluation metrics.

Recent advances in video generation have shown remarkable potential for constructing world simulators. However, current models still struggle to produce physically consistent results, particularly when handling large-scale or complex dynamics. This limitation arises primarily because existing approaches respond isotropically to physical prompts and neglect the fine-grained alignment between generated content and localized physical cues. To address these challenges, we propose ProPhy, a Progressive Physical Alignment Framework that enables explicit physics-aware conditioning and anisotropic generation. ProPhy employs a two-stage Mixture-of-Physics-Experts (MoPE) mechanism for discriminative physical prior extraction, where Semantic Experts infer semantic-level physical principles from textual descriptions, and Refinement Experts capture token-level physical dynamics. This mechanism allows the model to learn fine-grained, physics-aware video representations that better reflect underlying physical laws. Furthermore, we introduce a physical alignment strategy that transfers the physical reasoning capabilities of vision-language models (VLMs) into the Refinement Experts, facilitating a more accurate representation of dynamic physical phenomena. Extensive experiments on physics-aware video generation benchmarks demonstrate that ProPhy produces more realistic, dynamic, and physically coherent results than existing state-of-the-art methods.

Human motion generation plays a vital role in applications such as digital humans and humanoid robot control. However, most existing approaches disregard physics constraints, leading to the frequent production of physically implausible motions with pronounced artifacts such as floating and foot sliding. In this paper, we propose Morph, a Motion-free physics optimization framework, comprising a Motion Generator and a Motion Physics Refinement module, for enhancing physical plausibility without relying on costly real-world motion data. Specifically, the Motion Generator is responsible for providing large-scale synthetic motion data, while the Motion Physics Refinement Module utilizes these synthetic data to train a motion imitator within a physics simulator, enforcing physical constraints to project the noisy motions into a physically-plausible space. These physically refined motions, in turn, are used to fine-tune the Motion Generator, further enhancing its capability. Experiments on both text-to-motion and music-to-dance generation tasks demonstrate that our framework achieves state-of-the-art motion generation quality while improving physical plausibility drastically.

Physical AI aims to develop models that can perceive and predict real-world dynamics; yet, the extent to which current multi-modal large language models and video generative models support these abilities is insufficiently understood. We introduce Physical AI Bench (PAI-Bench), a unified and comprehensive benchmark that evaluates perception and prediction capabilities across video generation, conditional video generation, and video understanding, comprising 2,808 real-world cases with task-aligned metrics designed to capture physical plausibility and domain-specific reasoning. Our study provides a systematic assessment of recent models and shows that video generative models, despite strong visual fidelity, often struggle to maintain physically coherent dynamics, while multi-modal large language models exhibit limited performance in forecasting and causal interpretation. These observations suggest that current systems are still at an early stage in handling the perceptual and predictive demands of Physical AI. In summary, PAI-Bench establishes a realistic foundation for evaluating Physical AI and highlights key gaps that future systems must address.

Complementary metal-oxide semiconductor (CMOS) technology has radically reshaped the world by taking humanity to the digital age. Cramming more transistors into the same physical space has enabled an exponential increase in computational performance, a strategy that has been recently hampered by the increasing complexity and cost of miniaturization. To continue achieving significant gains in computing performance, new computing paradigms, such as quantum computing, must be developed. However, finding the optimal physical system to process quantum information, and scale it up to the large number of qubits necessary to build a general-purpose quantum computer, remains a significant challenge. Recent breakthroughs in nanodevice engineering have shown that qubits can now be manufactured in a similar fashion to silicon field-effect transistors, opening an opportunity to leverage the know-how of the CMOS industry to address the scaling challenge. In this article, we focus on the analysis of the scaling prospects of quantum computing systems based on CMOS technology.

Video generation models have achieved remarkable progress in creating high-quality, photorealistic content. However, their ability to accurately simulate physical phenomena remains a critical and unresolved challenge. This paper presents PhyWorldBench, a comprehensive benchmark designed to evaluate video generation models based on their adherence to the laws of physics. The benchmark covers multiple levels of physical phenomena, ranging from fundamental principles like object motion and energy conservation to more complex scenarios involving rigid body interactions and human or animal motion. Additionally, we introduce a novel ""Anti-Physics"" category, where prompts intentionally violate real-world physics, enabling the assessment of whether models can follow such instructions while maintaining logical consistency. Besides large-scale human evaluation, we also design a simple yet effective method that could utilize current MLLM to evaluate the physics realism in a zero-shot fashion. We evaluate 12 state-of-the-art text-to-video generation models, including five open-source and five proprietary models, with a detailed comparison and analysis. we identify pivotal challenges models face in adhering to real-world physics. Through systematic testing of their outputs across 1,050 curated prompts-spanning fundamental, composite, and anti-physics scenarios-we identify pivotal challenges these models face in adhering to real-world physics. We then rigorously examine their performance on diverse physical phenomena with varying prompt types, deriving targeted recommendations for crafting prompts that enhance fidelity to physical principles.

Imposing known physical constraints, such as conservation laws, during neural network training introduces an inductive bias that can improve accuracy, reliability, convergence, and data efficiency for modeling physical dynamics. While such constraints can be softly imposed via loss function penalties, recent advancements in differentiable physics and optimization improve performance by incorporating PDE-constrained optimization as individual layers in neural networks. This enables a stricter adherence to physical constraints. However, imposing hard constraints significantly increases computational and memory costs, especially for complex dynamical systems. This is because it requires solving an optimization problem over a large number of points in a mesh, representing spatial and temporal discretizations, which greatly increases the complexity of the constraint. To address this challenge, we develop a scalable approach to enforce hard physical constraints using Mixture-of-Experts (MoE), which can be used with any neural network architecture. Our approach imposes the constraint over smaller decomposed domains, each of which is solved by an "expert" through differentiable optimization. During training, each expert independently performs a localized backpropagation step by leveraging the implicit function theorem; the independence of each expert allows for parallelization across multiple GPUs. Compared to standard differentiable optimization, our scalable approach achieves greater accuracy in the neural PDE solver setting for predicting the dynamics of challenging non-linear systems. We also improve training stability and require significantly less computation time during both training and inference stages.

Diffusion policies have achieved remarkable success in robotic manipulation, yet they often fail to satisfy strict physical constraints required for safe deployment. Existing approaches impose safety either prematurely during training or reactively via external guardrails at test time, limiting policy expressivity and overall scalability. We propose Physical safety Alignment for Constrained Trajectories (PACT), a self-evolving post-training framework that projects pretrained diffusion policies onto constraint-feasible regions without accessing demonstration data or task rewards. PACT distills constraint gradients into the diffusion model through a reverse-KL objective with dense supervision across timesteps. It incorporates a curriculum that progressively tightens constraints while maintaining theoretically bounded policy shift and monotone improvement, mitigating the safety-performance trade-off from catastrophic forgetting. On simulated and real-world embodied manipulation benchmarks, PACT significantly reduces safety violations by 31.0% on average while improving task success by 30.7%.

Computing is conventionally implemented by hardware engineered for information processing. Here we investigate infrastructure-native computing: the use of a physical system built for another primary function as a fixed computational operator. In time-domain simulations of an IEEE 14-bus electrical network, Kirchhoff's current law and Ohm's law relate voltage-reference perturbations applied at distributed controllable nodes interfaced by power electronics converters to current responses through a topology-dependent transformation. A trained digital encoder and decoder exploit this transformation for image classification, reaching 91.5% accuracy on MNIST and 82.25% on Fashion-MNIST. The modeled operator is represented by 933 surrogate parameters, compared with 12,340 task-trained parameters for an accuracy-matched fully connected core transformation. Current superposition further supports concurrent spatial sharing of the operator and sequential temporal reuse, with per-stream accuracies above 85% and 93%, respectively, in surrogate-model evaluations. Evaluations on CIFAR-10 and repeated 10-class tasks sampled from a Butterflies-and-Moths dataset show that the incremental utility of the physical operator depends on the representation supplied by upstream digital feature extraction. These results provide a simulation-based proof of concept for infrastructure-native computing with electrical networks and identify topology, accessible control channels, and input representation as determinants of its computational utility.

For robots to robustly understand and interact with the physical world, it is highly beneficial to have a comprehensive representation - modelling geometry, physics, and visual observations - that informs perception, planning, and control algorithms. We propose a novel dual Gaussian-Particle representation that models the physical world while (i) enabling predictive simulation of future states and (ii) allowing online correction from visual observations in a dynamic world. Our representation comprises particles that capture the geometrical aspect of objects in the world and can be used alongside a particle-based physics system to anticipate physically plausible future states. Attached to these particles are 3D Gaussians that render images from any viewpoint through a splatting process thus capturing the visual state. By comparing the predicted and observed images, our approach generates visual forces that correct the particle positions while respecting known physical constraints. By integrating predictive physical modelling with continuous visually-derived corrections, our unified representation reasons about the present and future while synchronizing with reality. Our system runs in realtime at 30Hz using only 3 cameras. We validate our approach on 2D and 3D tracking tasks as well as photometric reconstruction quality. Videos are found at https://embodied-gaussians.github.io/.

Generative sequence models are often trained to plan motion in physical domains, from robotics to mechanical simulations. When constructing a dataset to train such a model, engineers may curate demonstrations to specify how trajectories should be distributed over a physical quantity like travel distance or mechanical energy. For example, a roboticist building a maze navigation agent might choose demonstrations whose travel distances cover a fixed range uniformly, hoping to constrain the agent's expected power usage. We find that standard deep learning can violate this intent: each generated trajectory can seem plausible on its own, but the aggregate distribution over the physical quantity is wrong. We call this failure physical misgeneralization, and develop an account of its mechanism. Using controlled synthetic tasks, we show that physical misgeneralization arises when local errors typical of the model class propagate through the physical measurement to shift the recovered distribution. We estimate these errors with a data deviation kernel, and we use it to predict which physical quantities gain or lose mass in both our synthetic and more applied maze navigation and double-pendulum motion tasks. Finally, our mechanistic interpretation helps identify which mitigation strategies are structurally promising, and we use it to propose a kernel-informed intervention.

Recent advances in generative video modeling, driven by large-scale datasets and powerful architectures, have yielded remarkable visual realism. However, emerging evidence suggests that simply scaling data and model size does not endow these systems with an understanding of the underlying physical laws that govern real-world dynamics. Existing approaches often fail to capture or enforce such physical consistency, resulting in unrealistic motion and dynamics. In his work, we investigate whether integrating the inference of latent physical properties directly into the video generation process can equip models with the ability to produce physically plausible videos. To this end, we propose Phantom, a Physics-Infused Video Generation model that jointly models the visual content and latent physical dynamics. Conditioned on observed video frames and inferred physical states, Phantom jointly predicts latent physical dynamics and generates future video frames. Phantom leverages a physics-aware video representation that serves as an abstract yet informaive embedding of the underlying physics, facilitating the joint prediction of physical dynamics alongside video content without requiring an explicit specification of a complex set of physical dynamics and properties. By integrating the inference of physical-aware video representation directly into the video generation process, Phantom produces video sequences that are both visually realistic and physically consistent. Quantitative and qualitative results on both standard video generation and physics-aware benchmarks demonstrate that Phantom not only outperforms existing methods in terms of adherence to physical dynamics but also delivers competitive perceptual fidelity.

Recent advances in generative foundational models, often termed "world models," have propelled interest in applying them to critical tasks like robotic planning and autonomous system training. For reliable deployment, these models must exhibit high physical fidelity, accurately simulating real-world dynamics. Existing physics-based video benchmarks, however, suffer from entanglement, where a single test simultaneously evaluates multiple physical laws and concepts, fundamentally limiting their diagnostic capability. We introduce WorldBench, a novel video-based benchmark specifically designed for concept-specific, disentangled evaluation, allowing us to rigorously isolate and assess understanding of a single physical concept or law at a time. To make WorldBench comprehensive, we design benchmarks at two different levels: 1) an evaluation of intuitive physical understanding with concepts such as object permanence or scale/perspective, and 2) an evaluation of low-level physical constants and material properties such as friction coefficients or fluid viscosity. When SOTA video-based world models are evaluated on WorldBench, we find specific patterns of failure in particular physics concepts, with all tested models lacking the physical consistency required to generate reliable real-world interactions. Through its concept-specific evaluation, WorldBench offers a more nuanced and scalable framework for rigorously evaluating the physical reasoning capabilities of video generation and world models, paving the way for more robust and generalizable world-model-driven learning.

Interlocking brick assemblies provide a standardized yet challenging testbed for contact-rich and long-horizon robotic manipulation, but existing rigid-body simulators do not faithfully capture snap-fit mechanics. We present BrickSim, the first real-time physics-based simulator for interlocking brick assemblies. BrickSim introduces a compact force-based mechanics model for snap-fit connections and solves the resulting internal force distribution using a structured convex quadratic program. Combined with a hybrid architecture that delegates rigid-body dynamics to the underlying physics engine while handling snap-fit mechanics separately, BrickSim enables real-time, high-fidelity simulation of assembly, disassembly, and structural collapse. On 150 real-world assemblies, BrickSim achieves 100% accuracy in static stability prediction with an average solve time of 5 ms. In dynamic drop tests, it also faithfully reproduces real-world structural collapse, precisely mirroring both the occurrence of breakage and the specific breakage locations. Built on Isaac Sim, BrickSim further supports seamless integration with a wide variety of robots and existing pipelines. We demonstrate robotic construction of brick assemblies using BrickSim, highlighting its potential as a foundation for research in dexterous, long-horizon robotic manipulation. BrickSim is open-source, and the code is available at https://github.com/intelligent-control-lab/BrickSim.

Joint audio-video generation models are rapidly approaching professional production quality, raising a central question: do they understand audio-visual physics, or merely generate plausible sounds and frames that violate real-world consistency? We introduce AV-Phys Bench, a benchmark for evaluating physical commonsense in joint audio-video generation. AV-Phys Bench tests models across three scene categories: Steady State, Event Transition, and Environment Transition. It covers physics-grounded subcategories drawn from real-world scenes, plus Anti-AV-Physics prompts that deliberately request physically inconsistent audio-video behavior. Each generation is evaluated along five dimensions: visual semantic adherence, audio semantic adherence, visual physical commonsense, audio physical commonsense, and cross-modal physical commonsense. Across three proprietary and four open-source models, we find that Seedance 2.0 performs best overall, but all models remain far from robust physical understanding. Performance drops sharply on event-driven and environment-driven transitions, and even strong proprietary systems collapse on Anti-AV-Physics prompts. We further introduce AV-Phys Agent, a ReAct-style evaluator that combines a multimodal language model with deterministic acoustic measurement tools, producing rankings that closely align with human ratings. Our results identify cross-modal physical consistency and transition-driven scene dynamics as key open challenges for joint audio-video generation.

As the demand for immersive 3D content grows, the need for intuitive and efficient interaction methods becomes paramount. Current techniques for physically manipulating 3D content within Virtual Reality (VR) often face significant limitations, including reliance on engineering-intensive processes and simplified geometric representations, such as tetrahedral cages, which can compromise visual fidelity and physical accuracy. In this paper, we introduce GS-Verse (Gaussian Splatting for Virtual Environment Rendering and Scene Editing), a novel method designed to overcome these challenges by directly integrating an object's mesh with a Gaussian Splatting (GS) representation. Our approach enables more precise surface approximation, leading to highly realistic deformations and interactions. By leveraging existing 3D mesh assets, GS-Verse facilitates seamless content reuse and simplifies the development workflow. Moreover, our system is designed to be physics-engine-agnostic, granting developers robust deployment flexibility. This versatile architecture delivers a highly realistic, adaptable, and intuitive approach to interactive 3D manipulation. We rigorously validate our method against the current state-of-the-art technique that couples VR with GS in a comparative user study involving 18 participants. Specifically, we demonstrate that our approach is statistically significantly better for physics-aware stretching manipulation and is also more consistent in other physics-based manipulations like twisting and shaking. Further evaluation across various interactions and scenes confirms that our method consistently delivers high and reliable performance, showing its potential as a plausible alternative to existing methods.

Generative Artificial Intelligence (AI) has rapidly advanced the field of computer vision by enabling machines to create and interpret visual data with unprecedented sophistication. This transformation builds upon a foundation of generative models to produce realistic images, videos, and 3D/4D content. Conventional generative models primarily focus on visual fidelity while often neglecting the physical plausibility of the generated content. This gap limits their effectiveness in applications that require adherence to real-world physical laws, such as robotics, autonomous systems, and scientific simulations. As generative models evolve to increasingly integrate physical realism and dynamic simulation, their potential to function as "world simulators" expands. Therefore, the field of physics-aware generation in computer vision is rapidly growing, calling for a comprehensive survey to provide a structured analysis of current efforts. To serve this purpose, the survey presents a systematic review, categorizing methods based on how they incorporate physical knowledge, either through explicit simulation or implicit learning. It also analyzes key paradigms, discusses evaluation protocols, and identifies future research directions. By offering a comprehensive overview, this survey aims to help future developments in physically grounded generation for computer vision. The reviewed papers are summarized at https://tinyurl.com/Physics-Aware-Generation.

In order for AI to be safely deployed in real-world scenarios such as hospitals, schools, and the workplace, it must be able to robustly reason about the physical world. Fundamental to this reasoning is physical common sense: understanding the physical properties and affordances of available objects, how they can be manipulated, and how they interact with other objects. Physical commonsense reasoning is fundamentally a multi-sensory task, since physical properties are manifested through multiple modalities - two of them being vision and acoustics. Our paper takes a step towards real-world physical commonsense reasoning by contributing PACS: the first audiovisual benchmark annotated for physical commonsense attributes. PACS contains 13,400 question-answer pairs, involving 1,377 unique physical commonsense questions and 1,526 videos. Our dataset provides new opportunities to advance the research field of physical reasoning by bringing audio as a core component of this multimodal problem. Using PACS, we evaluate multiple state-of-the-art models on our new challenging task. While some models show promising results (70% accuracy), they all fall short of human performance (95% accuracy). We conclude the paper by demonstrating the importance of multimodal reasoning and providing possible avenues for future research.

As LLMs advance their reasoning capabilities about the physical world, the absence of rigorous benchmarks for evaluating their ability to generate scientifically valid physical models has become a critical gap. Computational mechanics, which develops and applies mathematical models and numerical methods to predict the behavior of physical systems under forces, deformation, and constraints, provides an ideal foundation for structured scientific reasoning evaluation. Problems follow clear mathematical structure, enforce strict physical and numerical constraints, and support objective verification. The discipline requires constructing explicit models of physical systems and reasoning about geometry, spatial relationships, and material behavior, connecting directly to emerging AI goals in physical reasoning and world modeling. We introduce FEM-Bench, a computational mechanics benchmark designed to evaluate the ability of LLMs to generate correct finite element method (FEM) and related code. FEM-Bench 2025 contains a suite of introductory but nontrivial tasks aligned with material from a first graduate course on computational mechanics. These tasks capture essential numerical and physical modeling challenges while representing only a small fraction of the complexity present in the discipline. Despite their simplicity, state-of-the-art LLMs do not reliably solve all of them. In a five attempt run, the best performing model at function writing, Gemini 3 Pro, completed 30/33 tasks at least once and 26/33 tasks all five times. The best performing model at unit test writing, GPT-5, had an Average Joint Success Rate of 73.8%. Other popular models showed broad performance variation. FEM-Bench establishes a structured foundation for evaluating AI-generated scientific code, and future iterations will incorporate increasingly sophisticated tasks to track progress as models evolve.

A physically motivated equation that determines the number of electrons of a molecule is proposed based on chemical common sense. It shows that all molecules are entangled in the number of electrons and results in the fundamental assumption of molecular energy convexity that underpins molecular quantum mechanics. The proposed physical principle includes the molecular size consistency principle as a special case. Application of wavefunction theory to the principle shows that an individual molecule with a noninteger number of electrons is locally physical albeit locally unreal. The energy of a molecule is piecewise linear with respect to its continuous number of electrons. The continuity of the number of electrons allows the definition of an electronic chemical potential of a single molecule. A state function equivalent to the energy of a molecule can be defined using the chemical potential as a variable. The aforementioned physical principle can alternatively be expressed as a simple additivity with the new state function. The latter also shows that the quantum entanglement in the number of electrons can be viewed as all molecules sharing the same chemical potential.

Embodied AI is moving from isolated perception or action modules toward physical agents that understand, plan under goals, act through robot bodies, monitor progress, and improve from experience. Existing systems address this loop only in parts: end-to-end policies generate actions but often lack spatial reasoning, planning, and execution assessment, while robot-agent systems orchestrate tools or specialists but do not learn a shared representation. This fragmentation limits general Physical Agentic AI. We present ACE-Brain-0.5, a unified embodied foundation model that organizes robot intelligence into five coupled functions: spatial perception, decision making, embodied interaction, self-monitoring, and self-improvement. Built on ACE-Brain-0, which established spatial intelligence as a shared scaffold across robot platforms, ACE-Brain-0.5 extends an understanding-centric model into a closed-loop foundation model. A single 8B backbone instantiates the first four functions: grounding objects and affordances, reasoning over 3D and egocentric spatial relations, decomposing instructions into subgoals, generating navigation and manipulation actions, and estimating progress for verification and recovery. To unify these capabilities without cross-task interference, we introduce SSR+, which extends Scaffold-Specialize-Reconcile with a Reactivate stage after task-vector merging. The fifth function, self-improvement, is realized by a companion framework that updates external execution state, including task schemas, spatial memory, and failure-recovery cases, from rollouts. Across fifteen benchmarks, ACE-Brain-0.5 improves over ACE-Brain-0 on 14 of 18 spatial perception and grounding benchmarks, achieves competitive navigation and manipulation performance, and provides strong progress estimation in ID and OOD settings. Together, these results mark an early step toward general Physical Agentic AI.

Creating deformable assets for robot manipulation requires jointly specifying their geometry, appearance, and physical properties. This is especially challenging for deformable objects, since text and images provide limited evidence about how they deform and respond to contact, yet these responses directly affect their suitability for interaction. Automated generation therefore needs to resolve coupled physical requirements and use interaction evidence to guide construction and refinement. We present DeformSmith, a framework that enables automated generation of interactive, physically credible deformable assets from text or a single image. Through hierarchical agentic construction and a shared physics-grounded harness, it progressively builds, tests, and refines geometry, physical models, material behavior, and robot interaction until the resulting asset is ready for simulation and manipulation. Robot interaction closes the generation loop through manipulation feedback and replayable interaction data. Results show that DeformSmith generates assets with better visual quality and physical plausibility than state-of-the-art baselines, including PhysGen3D, PhysGM, and PhysX-Omni, while supporting the synthesis of data for robotic manipulation of deformable objects. Project page: https://can-lee.github.io/deformsmith-web/

A digital twin is a virtual replica of a real-world physical phenomena that uses mathematical modeling to characterize and simulate its defining features. By constructing digital twins for disease processes, we can perform in-silico simulations that mimic patients' health conditions and counterfactual outcomes under hypothetical interventions in a virtual setting. This eliminates the need for invasive procedures or uncertain treatment decisions. In this paper, we propose a method to identify digital twin model parameters using only noninvasive patient health data. We approach the digital twin modeling as a composite inverse problem, and observe that its structure resembles pretraining and finetuning in self-supervised learning (SSL). Leveraging this, we introduce a physics-informed SSL algorithm that initially pretrains a neural network on the pretext task of solving the physical model equations. Subsequently, the model is trained to reconstruct low-dimensional health measurements from noninvasive modalities while being constrained by the physical equations learned in pretraining. We apply our method to identify digital twins of cardiac hemodynamics using noninvasive echocardiogram videos, and demonstrate its utility in unsupervised disease detection and in-silico clinical trials.

In an industrial group like Safran, numerical simulations of physical phenomena are integral to most design processes. At Safran's corporate research center, we enhance these processes by developing fast and reliable surrogate models for various physics. We focus here on two technologies developed in recent years. The first is a physical reduced-order modeling method for non-linear structural mechanics and thermal analysis, used for calculating the lifespan of high-pressure turbine blades and performing heat analysis of high-pressure compressors. The second technology involves learning physics simulations with non-parameterized geometrical variability using classical machine learning tools, such as Gaussian process regression. Finally, we present our contributions to the open-source and open-data community.

The design of complex machines stands as both a marker of human intelligence and a foundation of engineering practice. Given recent advances in large language models (LLMs), we ask whether they, too, can learn to create. We approach this question through the lens of compositional machine design: a task in which machines are assembled from standardized components to meet functional demands like locomotion or manipulation in a simulated physical environment. To support this investigation, we introduce BesiegeField, a testbed built on the machine-building game Besiege, which enables part-based construction, physical simulation and reward-driven evaluation. Using BesiegeField, we benchmark state-of-the-art LLMs with agentic workflows and identify key capabilities required for success, including spatial reasoning, strategic assembly, and instruction-following. As current open-source models fall short, we explore reinforcement learning (RL) as a path to improvement: we curate a cold-start dataset, conduct RL finetuning experiments, and highlight open challenges at the intersection of language, machine design, and physical reasoning.

This paper presents two industry-grade datasets captured during an 8-hour continuous operation of the manufacturing assembly line at the Future Factories Lab, University of South Carolina, on 08/13/2024. The datasets adhere to industry standards, covering communication protocols, actuators, control mechanisms, transducers, sensors, and cameras. Data collection utilized both integrated and external sensors throughout the laboratory, including sensors embedded within the actuators and externally installed devices. Additionally, high-performance cameras captured key aspects of the operation. In a prior experiment [1], a 30-hour continuous run was conducted, during which all anomalies were documented. Maintenance procedures were subsequently implemented to reduce potential errors and operational disruptions. The two datasets include: (1) a time-series analog dataset, and (2) a multi-modal time-series dataset containing synchronized system data and images. These datasets aim to support future research in advancing manufacturing processes by providing a platform for testing novel algorithms without the need to recreate physical manufacturing environments. Moreover, the datasets are open-source and designed to facilitate the training of artificial intelligence models, streamlining research by offering comprehensive, ready-to-use resources for various applications and projects.

Evaluating whether a vision-language model (VLM) can act through a physical body is challenging. The outcome of an action couples the VLM's decision with motor control. When a task fails, it is hard to tell whether the VLM made a bad choice or the motor controller simply failed to execute it, e.g., losing balance and falling. In this work, we introduce HumanCLAW, an evaluation framework that decouples action decision-making from low-level execution. At every step, a harnessed, off-the-shelf VLM issues an atomic skill command, and the command is translated into a sub-second chunk of continuous full-body motion with real physical consequences, including gravity and collisions. The body can therefore act freely in the physical world, while execution-side disturbances, balance and motor errors, are factored out. What remains measurable is the model's action intelligence: its moment-to-moment choice of what the body should execute next. Based on this framework, we build HumanCLAW-Bench: 1,218 long-horizon, egocentric find-navigate-interact episodes across 41 indoor scenes. We test nine state-of-the-art VLMs and find that none solves the benchmark; the best model reaches only a 16.8% success rate. Recognizing the target is not the bottleneck. What current VLMs lack is embodied self-awareness: they lose track of their own body, failing to tell where it is, whether it has reached the goal, or whether it has hit an obstacle.

The ability to transform a flat sheet into a complex three-dimensional structure is a fundamental test of physical intelligence. Unlike cloth manipulation, origami is governed by strict geometric axioms and hard kinematic constraints, where a single invalid crease or collision can invalidate the entire folding sequence. As a result, origami demands long-horizon constructive reasoning that jointly satisfies precise physical laws and high-level semantic intent. Existing approaches fall into two disjoint paradigms: optimization-based methods enforce physical validity but require dense, precisely specified inputs, making them unsuitable for sparse natural language descriptions, while generative foundation models excel at semantic and perceptual synthesis yet fail to produce long-horizon, physics-consistent folding processes. Consequently, generating valid origami folding sequences directly from text remains an open challenge. To address this gap, we introduce Learn2Fold, a neuro-symbolic framework that formulates origami folding as conditional program induction over a crease-pattern graph. Our key insight is to decouple semantic proposal from physical verification. A large language model generates candidate folding programs from abstract text prompts, while a learned graph-structured world model serves as a differentiable surrogate simulator that predicts physical feasibility and failure modes before execution. Integrated within a lookahead planning loop, Learn2Fold enables robust generation of physically valid folding sequences for complex and out-of-distribution patterns, demonstrating that effective spatial intelligence arises from the synergy between symbolic reasoning and grounded physical simulation.

Existing video generation models excel at producing photo-realistic videos from text or images, but often lack physical plausibility and 3D controllability. To overcome these limitations, we introduce PhysCtrl, a novel framework for physics-grounded image-to-video generation with physical parameters and force control. At its core is a generative physics network that learns the distribution of physical dynamics across four materials (elastic, sand, plasticine, and rigid) via a diffusion model conditioned on physics parameters and applied forces. We represent physical dynamics as 3D point trajectories and train on a large-scale synthetic dataset of 550K animations generated by physics simulators. We enhance the diffusion model with a novel spatiotemporal attention block that emulates particle interactions and incorporates physics-based constraints during training to enforce physical plausibility. Experiments show that PhysCtrl generates realistic, physics-grounded motion trajectories which, when used to drive image-to-video models, yield high-fidelity, controllable videos that outperform existing methods in both visual quality and physical plausibility. Project Page: https://cwchenwang.github.io/physctrl

Building AI systems that can plan, act, and create in the physical world requires more than pattern recognition. Such systems must understand the causal mechanisms and constraints governing physical processes in order to guide sequential decisions. This capability relies on internal representations, analogous to an internal language model, that relate observations, actions, and resulting environmental changes. However, many existing benchmarks treat visual perception and programmatic reasoning as separate problems, focusing either on visual recognition or on symbolic tasks. The domain of origami provides a natural testbed that integrates these modalities. Constructing shapes through folding operations requires visual perception, reasoning about geometric and physical constraints, and sequential planning, while remaining sufficiently structured for systematic evaluation. We introduce OrigamiBench, an interactive benchmark in which models iteratively propose folds and receive feedback on physical validity and similarity to a target configuration. Experiments with modern vision-language models show that scaling model size alone does not reliably produce causal reasoning about physical transformations. Models fail to generate coherent multi-step folding strategies, suggesting that visual and language representations remain weakly integrated.