Daily Papers

The Verwey transition in magnetite is a benchmark electronically driven phase transition that is highly sensitive to lattice imperfections and external perturbations. Doping, deviations from oxygen stoichiometry, and irradiation-induced point defects are known to lower the Verwey transition temperature, T_{rm V}. By contrast, the role of remanent strain fields and extended defect structures generated by uniaxial stress has remained largely unexplored. Here we combine dark-field x-ray microscopy (DFXM) and ac magnetic susceptibility to determine how strain-induced defects affect the Verwey transition in stoichiometric single-crystalline magnetite after uniaxial compression and unloading. The DFXM measurements were performed on two samples compressed along the same [011] direction: loading to 200~MPa generated stable line-like defects and remanent strain fields, whereas loading beyond the fracture threshold produced denser defect networks and mechanical fracture. To test the effect of a different loading geometry, we also measured the ac susceptibility of a sample fractured by compression along [001]. Real-space DFXM imaging, lattice-orientation mapping, and residual strain mapping show substantial remanent structural disorder after compression. Nevertheless, neither the transition temperature T_{rm V} nor the sharpness of the transition changes measurably in any of the compressed or fractured samples. This behavior contrasts with the strong suppression of T_{rm V} by point-like disorder. Our results show that extended line-like defects and remanent strain fields produced by plastic deformation do not measurably perturb the macroscopic electronic ordering responsible for the Verwey transition, thereby distinguishing the effects of point defects from those of extended slip-related defects in magnetite.

Recent flow cessation experiments on soft materials have shown a counter-intuitive non-monotonic relaxation of the shear stress: following the switch-off of a steady imposed shear flow, the stress initially decays before later increasing again. By simulating the soft glassy rheology model in a form extended to allow steady state shear banding, we show that the presence of shear bands prior to flow cessation can give rise to this phenomenon. We give a mechanistic understanding of the basic physics involved, in terms of (i) the decay of the shear bands after flow cessation, and (ii) the evolution of frustrated local stresses, governed by different time scales for plastic relaxation in each band. In particular, an elastic recoil in the unsheared band gives rise to negative local frustrated stresses, the slow release of which can cause an increase in macroscopic stress. Given that shear banding and frustrated local stresses arise widely across disordered soft solids, we argue that non-monotonic stress relaxation after flow cessation may occur in many different materials.

This paper proposes a formal framework for reverse stress testing geopolitical risk in corporate credit portfolios. A joint macro-financial scenario vector, augmented with an explicit geopolitical risk factor, is mapped into stressed probabilities of default and losses given default. These stresses are then propagated to portfolio tail losses through a latent factor structure and translated into a stressed CET1 ratio, jointly accounting for capital depletion and risk-weighted asset dynamics. Reverse stress testing is formulated as a constrained maximum likelihood problem over the scenario space. This yields a geopolitical point reverse stress test, or design point, defined as the most probable scenario that breaches a prescribed capital adequacy constraint under a reference distribution. The framework further characterises neighbourhoods and near optimal sets of reverse stress scenarios, allowing for sensitivity analysis and governance oriented interpretation. The approach is compatible with internal rating based models and supports implementation at the exposure or sector level.

In this work, we investigate the transient rheological behavior of two soft glassy materials: a clay dispersion and a silica gel, emphasizing their unconventional shear stress build-up behavior under conditions of constant imposed strain. For both materials, the elastic modulus and static yield stress undergo time-dependent evolution or aging. In addition, following an intense period of pre-shearing (i.e. shear-melting or destructuration), the material relaxation time is observed to show a stronger than linear dependence on the sample age, suggestive of hyper-aging dynamics. We show that these features are consistent with non-monotonic steady-state shear stress/shear rate flow curves characterized by a local stress minimum. When a steady shear flow is suddenly ceased, and the total imposed sample strain is held constant, both materials show an initial relaxation of the shear stress followed by a period of shear stress buildup, resulting in a local minimum in the evolution of shear stress with time. For the clay dispersion, the intensity of these effects increases with higher pre-shear rates, whereas for the silica gel, the effects are largely independent of the pre-shear rate. We also propose a simple time-dependent linear Maxwell model, which qualitatively predicts the experimentally observed trends in which the shear stress build-up is directly related to a monotonic increase in the elastic modulus, giving keen insight into this peculiar phenomenon.

Magnetic Resonance Imaging with tagging (tMRI) has long been utilized for quantifying tissue motion and strain during deformation. However, a phenomenon known as tag fading, a gradual decrease in tag visibility over time, often complicates post-processing. The first contribution of this study is to model tag fading by considering the interplay between T_1 relaxation and the repeated application of radio frequency (RF) pulses during serial imaging sequences. This is a factor that has been overlooked in prior research on tMRI post-processing. Further, we have observed an emerging trend of utilizing raw tagged MRI within a deep learning-based (DL) registration framework for motion estimation. In this work, we evaluate and analyze the impact of commonly used image similarity objectives in training DL registrations on raw tMRI. This is then compared with the Harmonic Phase-based approach, a traditional approach which is claimed to be robust to tag fading. Our findings, derived from both simulated images and an actual phantom scan, reveal the limitations of various similarity losses in raw tMRI and emphasize caution in registration tasks where image intensity changes over time.

This study explores cardiovascular stents fabricated using laser powder bed fusion (LPBF); an emerging method to offer patient-specific customisable parts. Here, the shape memory alloy NiTi, in a near equiatomic composition, was investigated to deconvolve the material response from macroscopic component effects. Specifically, stress-geometry interactions were revealed, in-situ, for a minaturised cardiovascular stent subjected to an externally applied cylindrical stress whilst acquiring synchrotron X-ray imaging and diffraction data. The approach enabled the collection of spatially resolved micromechanical deformation data; the formation of stress-induced martensite and R-phase was evident, occurring in locations near junctions between stent ligaments where stress concentrations exist. In the as-fabricated condition, hardness maps were obtained through nanoindentation, demonstrating that the localised deformation and deformation patterning is further controlled by porosity and microstructural heterogeneity. Electron backscatter diffraction (EBSD) supported these observations, showing a finer grain structure near stent junctions with higher associated lattice curvature. These features, combined with stress concentrations when loaded will initiate localised phase transformations. If the stent was subjected to repeated loading, representing in-vivo conditions, these regions would be susceptible to cyclic damage through transformation memory loss, leading to premature component failure. This study highlights the challenges that must be addressed for the post-processing treatment of LABF-processed stents for healthcare-related applications.