Daily Papers

Deep reinforcement learning (RL) has driven rapid progress in physically-based motion generation, yet synthesizing robust motion policies in dense fluid environments (e.g. swimming) remains unsolved. Unlike land motion, where environmental impact is sparse and can be coarsely modeled (e.g. gravity, normal reaction), swimming requires continuous, full-body coordination under pressure and flow forces across the entire body surface; fully-coupled rigid-fluid simulation is far too slow for the millions of interactions RL requires. We propose SWIM, an RL framework for physically-based human swimming learned from a single reference motion. Its core is a compact, low-dimensional environment representation: a dual-branch graph-convolutional VQ-VAE that tokenizes per-link body-water forces and torques, informative enough for control yet robust to the rapidly changing force exchanges that would otherwise destabilize training. We pair this with a GPU-based Lagrangian solver with rigid-fluid coupling that yields 10-15x faster training. Across hundreds of training runs and several hundred zero-shot conditions, SWIM generalizes to unseen goals and trajectories, fluids with varying density, external flows and perturbations, altered body morphologies, and all four competitive swimming styles. Against imitation-learning baselines (MimicKit-DeepMimic, MimicKit-AMP, ADD) and alternative force models (a PINN world model, MuJoCo's inertial fluid model, and an underwater-robotics simulator), SWIM achieves better stability, goal satisfaction, and physical realism: a 63.9% success rate on held-out generalization versus 36.8% for the strongest baseline.

We investigate solutions to a coupled system of partial differential equations that describe a multilayered filtration system. Namely, we study the interaction of a viscous incompressible flow with bulk poroelasticity, via a poroelastic interface. The configuration consists of two 3D toroidal subdomains connected via a plate interface, which permits elastic deformation and perfusive fluid dynamics. The governing dynamics comprise Stokes equations in the bulk fluid region, Biot's equations in the bulk poroelastic region, and the recent poroplate of Mikelić at the interface. Coupling occurs on the top and lower surfaces of the plate, and involves conservation of mass, stress balance, and a certain slip condition for the fluid free-flow. We seek strong (and mild) solutions in the Hilbert space framework via the Lumer-Phillips theorem. The resolvent analysis employs a nonstandard mixed variational formulation which captures the complex, multi-physics coupling at the interface. We explicitly characterize the infinitesimal generator associated to the linear Cauchy problem and establish the generation of a C_0-semigroup on a suitably chosen finite-energy space. With the semigroup in hand, we may treat elastic nonlinearities for plate displacements through perturbation theory. These result parallel those for Biot-Stokes filtration systems, and complement the recently established weak solution theory for multilayer filtrations. The agency of the semigroup straightforwardly admits structural (plate) nonlinearity into the dynamics. Future stability and regularity analyses for multilayer filtrations are also made possible by these results, as well as a comparison of spectral and regularity properties between filtration configurations, and the elucidation of the mitigating poroplate dynamics as possibly regularizing and stabilizing.

The proposed method aims to approximate a solution of a fluid-fluid interaction problem in case of low viscosities. The nonlinear interface condition on the joint boundary allows for this problem to be viewed as a simplified version of the atmosphere-ocean coupling. Thus, the proposed method should be viewed as potentially applicable to air-sea coupled flows in turbulent regime. The method consists of two key ingredients. The geometric averaging approach is used for efficient and stable decoupling of the problem, which would allow for the usage of preexisting codes for the air and sea domain separately, as "black boxes". This is combined with the variational multiscale stabilization technique for treating flows at high Reynolds numbers. We prove the stability and accuracy of the method and provide several numerical tests to assess both the quantitative and qualitative features of the computed solution.

Humans manipulate various kinds of fluids in their everyday life: creating latte art, scooping floating objects from water, rolling an ice cream cone, etc. Using robots to augment or replace human labors in these daily settings remain as a challenging task due to the multifaceted complexities of fluids. Previous research in robotic fluid manipulation mostly consider fluids governed by an ideal, Newtonian model in simple task settings (e.g., pouring). However, the vast majority of real-world fluid systems manifest their complexities in terms of the fluid's complex material behaviors and multi-component interactions, both of which were well beyond the scope of the current literature. To evaluate robot learning algorithms on understanding and interacting with such complex fluid systems, a comprehensive virtual platform with versatile simulation capabilities and well-established tasks is needed. In this work, we introduce FluidLab, a simulation environment with a diverse set of manipulation tasks involving complex fluid dynamics. These tasks address interactions between solid and fluid as well as among multiple fluids. At the heart of our platform is a fully differentiable physics simulator, FluidEngine, providing GPU-accelerated simulations and gradient calculations for various material types and their couplings. We identify several challenges for fluid manipulation learning by evaluating a set of reinforcement learning and trajectory optimization methods on our platform. To address these challenges, we propose several domain-specific optimization schemes coupled with differentiable physics, which are empirically shown to be effective in tackling optimization problems featured by fluid system's non-convex and non-smooth properties. Furthermore, we demonstrate reasonable sim-to-real transfer by deploying optimized trajectories in real-world settings.

We investigate the coupling effects of the two-phase interface, viscosity ratio, and density ratio of the dispersed phase to the continuous phase on the flow statistics in two-phase Taylor-Couette turbulence at a system Reynolds number of 6000 and a system Weber number of 10 using interface-resolved three-dimensional direct numerical simulations with the volume-of-fluid method. Our study focuses on four different scenarios: neutral droplets, low-viscosity droplets, light droplets, and low-viscosity light droplets. We find that neutral droplets and low-viscosity droplets primarily contribute to drag enhancement through the two-phase interface, while light droplets reduce the system's drag by explicitly reducing Reynolds stress due to the density dependence of Reynolds stress. Additionally, low-viscosity light droplets contribute to greater drag reduction by further reducing momentum transport near the inner cylinder and implicitly reducing Reynolds stress. While interfacial tension enhances turbulent kinetic energy (TKE) transport, drag enhancement is not strongly correlated with TKE transport for both neutral droplets and low-viscosity droplets. Light droplets primarily reduce the production term by diminishing Reynolds stress, whereas the density contrast between the phases boosts TKE transport near the inner wall. Therefore, the reduction in the dissipation rate is predominantly attributed to decreased turbulence production, causing drag reduction. For low-viscosity light droplets, the production term diminishes further, primarily due to their greater reduction in Reynolds stress, while reduced viscosity weakens the density difference's contribution to TKE transport near the inner cylinder, resulting in a more pronounced reduction in the dissipation rate and consequently stronger drag reduction. Our findings provide new insights into the turbulence modulation in two-phase flow.

Achieving scalable coordination in large robotic swarms is often constrained by reliance on inter-agent communication, which introduces latency, bandwidth limitations, and vulnerability to failure. To address this gap, a decentralized approach for outer-loop control of large multi-agent systems based on the paradigm of how a fluid moves through a volume is proposed and evaluated. A relationship between fundamental fluidic element properties and individual robotic agent states is developed such that the corresponding swarm "flows" through a space, akin to a fluid when forced via a pressure boundary condition. By ascribing fluid-like properties to subsets of agents, the swarm evolves collectively while maintaining desirable structure and coherence without explicit communication of agent states within or outside of the swarm. The approach is evaluated using simulations involving O(10^3) quadcopter agents and compared against Computational Fluid Dynamics (CFD) solutions for a converging-diverging domain. Quantitative agreement between swarm-derived and CFD fields is assessed using Root-Mean-Square Error (RMSE), yielding normalized errors of 0.15-0.9 for velocity, 0.61-0.98 for density, 0-0.937 for pressure. These results demonstrate the feasibility of treating large robotic swarms as continuum systems that retain the macroscopic structure derived from first principles, providing a basis for scalable and decentralized control.

We propose a neural physics system for real-time, interactive fluid simulations. Traditional physics-based methods, while accurate, are computationally intensive and suffer from latency issues. Recent machine-learning methods reduce computational costs while preserving fidelity; yet most still fail to satisfy the latency constraints for real-time use and lack support for interactive applications. To bridge this gap, we introduce a novel hybrid method that integrates numerical simulation, neural physics, and generative control. Our neural physics jointly pursues low-latency simulation and high physical fidelity by employing a fallback safeguard to classical numerical solvers. Furthermore, we develop a diffusion-based controller that is trained using a reverse modeling strategy to generate external dynamic force fields for fluid manipulation. Our system demonstrates robust performance across diverse 2D/3D scenarios, material types, and obstacle interactions, achieving real-time simulations at high frame rates (11~29% latency) while enabling fluid control guided by user-friendly freehand sketches. We present a significant step towards practical, controllable, and physically plausible fluid simulations for real-time interactive applications. We promise to release both models and data upon acceptance.

We derive a thermodynamically-consistent model of fluid flow through a poroelastic medium. Starting from elastic and fluid free-energy densities, an energy-dissipation rate, and a kinematic constraint, the force-balance equations are derived using variational principles, with the pressure--density constitutive relation emerging as a direct consequence of the variational structure; the same kinematic constraint also supplies the total-flux transport structure. In the ideal-gas limit, the model linearization recovers the classical linear Biot equations. For power-law fluid energies, it yields isentropic pressure--density relations. A key advantage of the variational formulation is that extensions to richer physics, such as thermal effects, chemical reactions, or multi-component fluids, can be incorporated systematically by augmenting the energy and dissipation functionals without redesigning the force-balance or transport closure. We support the model with an energy-compatible two-field discretization and study consolidation under a surface load with three lateral-boundary treatments and three fluid-compressibility exponents.

Text- and image-conditioned video generation models have achieved strong visual fidelity and temporal coherence, but they often fail to generate motion governed by kinematic and geometric constraints. In these settings, object parts must remain rigid, maintain contact or coupling with neighboring components, and transfer motion consistently across connected parts. These requirements are especially explicit in articulated mechanical assemblies, where motion is constrained by rigid-link geometry, contact/coupling relations, and transmission through kinematic chains. A generated video may therefore appear plausible while violating the intended mechanism, such as rotating a part that should translate, deforming a rigid component, breaking coupling between parts, or failing to move downstream components. To evaluate this gap, We introduce MechVerse, a benchmark for mechanically consistent image-to-video generation. MechVerse contains 21,156 synthetic clips from 1,357 mechanical assemblies across 141 categories, organized into three tiers of increasing kinematic complexity: independent articulation, pairwise coupling, and densely coupled multi-part mechanisms. Each clip is paired with a structured prompt describing part identities, stationary supports, moving components, motion primitives, direction, speed/extent, and inter-part dependencies. We evaluate proprietary, open-source, and fine-tuned image-to-video models using standard video metrics, instruction-following scores, and human judgments of motion correctness and kinematic coupling. Results show that current models can preserve appearance and smoothness while failing to generate mechanically admissible motion, with errors increasing as coupling complexity grows. MechVerse provides a benchmark for measuring and improving mechanism-aware video generation from image and language inputs.

Flow matching has emerged as a compelling generative modeling approach that is widely used across domains. To generate data via a flow matching model, an ordinary differential equation (ODE) is numerically solved via forward integration of the modeled velocity field. To better capture the multi-modality that is inherent in typical velocity fields, hierarchical flow matching was recently introduced. It uses a hierarchy of ODEs that are numerically integrated when generating data. This hierarchy of ODEs captures the multi-modal velocity distribution just like vanilla flow matching is capable of modeling a multi-modal data distribution. While this hierarchy enables to model multi-modal velocity distributions, the complexity of the modeled distribution remains identical across levels of the hierarchy. In this paper, we study how to gradually adjust the complexity of the distributions across different levels of the hierarchy via mini-batch couplings. We show the benefits of mini-batch couplings in hierarchical rectified flow matching via compelling results on synthetic and imaging data. Code is available at https://riccizz.github.io/HRF_coupling.

In this paper, we investigate the stability threshold of the two-dimensional Boussinesq system around the Couette flow in an infinite channel Rtimes[-1,1] under Navier-slip boundary condition. To address nonlinear echo chains induced by temperature-vorticity coupling, we construct a two-level frequency-dependent temporal decomposition, with the two levels matched to the infinite and finite superposition principles for the equation, respectively. By fully exploiting the enhanced dissipation effect at each decomposition level, we prove that if the initial perturbation (ω^{in}, θ^{in}) around the Couette flow satisfies |ω^{in}|_{H^4_{x,y}cap L^1_xH^4_y}leq cν^{1{3}}, and |θ^{in}|_{H^5_{x,y}cap L^1_xH^5_y}leq cν^{2{3}+}, the Boussinesq system admits a globally asymptotically stable solution. It should be emphasized that the method in this paper provides an effective approach for the hydrodynamic equations with coupling effects.

Recently, many mesh-based graph neural network (GNN) models have been proposed for modeling complex high-dimensional physical systems. Remarkable achievements have been made in significantly reducing the solving time compared to traditional numerical solvers. These methods are typically designed to i) reduce the computational cost in solving physical dynamics and/or ii) propose techniques to enhance the solution accuracy in fluid and rigid body dynamics. However, it remains under-explored whether they are effective in addressing the challenges of flexible body dynamics, where instantaneous collisions occur within a very short timeframe. In this paper, we present Hierarchical Contact Mesh Transformer (HCMT), which uses hierarchical mesh structures and can learn long-range dependencies (occurred by collisions) among spatially distant positions of a body -- two close positions in a higher-level mesh correspond to two distant positions in a lower-level mesh. HCMT enables long-range interactions, and the hierarchical mesh structure quickly propagates collision effects to faraway positions. To this end, it consists of a contact mesh Transformer and a hierarchical mesh Transformer (CMT and HMT, respectively). Lastly, we propose a flexible body dynamics dataset, consisting of trajectories that reflect experimental settings frequently used in the display industry for product designs. We also compare the performance of several baselines using well-known benchmark datasets. Our results show that HCMT provides significant performance improvements over existing methods. Our code is available at https://github.com/yuyudeep/hcmt.

We consider the scattering of acoustic perturbations in a presence of a flow. We suppose that the space can be split into a zone where the flow is uniform and a zone where the flow is potential. In the first zone, we apply a Prandtl-Glauert transformation to recover the Helmholtz equation. The well-known setting of boundary element method for the Helmholtz equation is available. In the second zone, the flow quantities are space dependent, we have to consider a local resolution, namely the finite element method. Herein, we carry out the coupling of these two methods and present various applications and validation test cases. The source term is given through the decomposition of an incident acoustic field on a section of the computational domain's boundary.

We study the problem of the transformation of a given reactant species into an immiscible product species, as they flow through a chemically active porous medium. We derive the equation governing the evolution of the volume fraction of the species -- in a one-dimensional macroscopic description --, identify the relevant dimensionless numbers, and provide simple models for capillary pressure and relative permeabilities, which are quantities of crucial importance when tackling multiphase flows in porous media. We set the domain of validity of our models and discuss the importance of viscous coupling terms in the extended Darcy's law. We investigate numerically the steady regime and demonstrate that the spatial transformation rate of the species along the reactor is non-monotonous, as testified by the existence of an inflection point in the volume fraction profiles. We obtain the scaling of the location of this inflection point with the dimensionless lengths of the problem. Eventually, we provide key elements for optimization of the reactor.

We first prove a rigidity result for uniformly rotating vortex patch solutions to Euler equations in bounded simply-connected planar domains. Namely, if a bounded simply-connected domain with real-analytic boundary contains a nontrivial vortex patch that remains strictly inside the domain while undergoing a uniform rigid rotation, then the ambient domain must be a disc centered at the rotation center. The proof combines the rotating-frame formulation with harmonic unique continuation and the generalized Schwarz's reflection principle across analytic boundary arcs. These tools imply that, unless the outer domain is rotationally invariant, the velocity must vanish in an open region surrounding the patch, contradicting the nonzero circulation generated by the patch. In the same spirit, we show that only circular domains possess a circular point vortex orbit. As a second result, we construct quasi-periodic vortex patch solutions to the Euler equations in domains that are small perturbations of the unit disc D. The amplitudes of the solutions are linked to the size of the domain deformation, allowing the classical Rankine vortices bcdotD, bin(0,1), to be regarded as equilibrium states. Our analysis is perturbative with respect to the construction developed in the undeformed case, and the resulting quasi-periodic solutions exist for most values of the inner radius b. This provides the first construction of quasi-periodic vortex patch solutions to the Euler equations in non-radial domains. Moreover, combined with the rigidity result established above, this shows that, in the periodic case, these solutions cannot arise from a purely rigid rotation.

We study the dynamics of an inextensible, closed interface subject to bending forces and immersed in a two-dimensional and incompressible Stokes fluid. We formulate the problem as a boundary integral equation in terms of the tangent angle and demonstrate the well-posedness in suitable time-weighted spaces of the resulting nonlinear and nonlocal system. The solution is furthermore shown to be smooth for positive times. Numerical computations are performed to initiate the study of the long-time behavior of the interface.

Fluid-structure interaction is common in engineering and natural systems, where floating-body motion is governed by added mass, drag, and background flows. Modeling these dissipative dynamics is difficult: black-box neural models regress state derivatives with limited interpretability and unstable long-horizon predictions. We propose Floating-Body Hydrodynamic Neural Networks (FHNN), a physics-structured framework that predicts interpretable hydrodynamic parameters such as directional added masses, drag coefficients, and a streamfunction-based flow, and couples them with analytic equations of motion. This design constrains the hypothesis space, enhances interpretability, and stabilizes integration. On synthetic vortex datasets, FHNN achieves up to an order-of-magnitude lower error than Neural ODEs, recovers physically consistent flow fields. Compared with Hamiltonian and Lagrangian neural networks, FHNN more effectively handles dissipative dynamics while preserving interpretability, which bridges the gap between black-box learning and transparent system identification.

We consider the relationship between Eulerian modal decompositions and Lagrangian coherent structures (LCSs). The model sensitivity framework developed by Kaszás and Haller (2020) is used to express data-driven modal representations of fluid flow in a Lagrangian space. The method, based on the computation of the finite-time Lyapunov exponent, computes the amplitude perturbations experienced by fluid particles due to specific modal components of the flow. Demonstrations of the method are presented for both periodic and turbulent flows, including experimental data from the wake past an oscillating foil, numerical data of the classical cylinder wake flow, and a direct numerical simulation (DNS) of a turbulent channel flow. This method provides a way to understand how Eulerian mode structures interact dynamically with features of the Lagrangian coherent structure across scales, offering additional physical insight into modal decompositions.

Recently, data-driven simulators based on graph neural networks have gained attention in modeling physical systems on unstructured meshes. However, they struggle with long-range dependencies in fluid flows, particularly in refined mesh regions. This challenge, known as the 'over-squashing' problem, hinders information propagation. While existing graph rewiring methods address this issue to some extent, they only consider graph topology, overlooking the underlying physical phenomena. We propose Physics-Informed Ollivier-Ricci Flow (PIORF), a novel rewiring method that combines physical correlations with graph topology. PIORF uses Ollivier-Ricci curvature (ORC) to identify bottleneck regions and connects these areas with nodes in high-velocity gradient nodes, enabling long-range interactions and mitigating over-squashing. Our approach is computationally efficient in rewiring edges and can scale to larger simulations. Experimental results on 3 fluid dynamics benchmark datasets show that PIORF consistently outperforms baseline models and existing rewiring methods, achieving up to 26.2 improvement.

A finite difference scheme is used to develop a numerical method to solve the flow of an unbounded viscoelastic fluid with zero to moderate inertia around a prolate spheroidal particle. The equations are written in prolate spheroidal coordinates, and the shape of the particle is exactly resolved as one of the coordinate surfaces representing the inner boundary of the computational domain. As the prolate spheroidal grid is naturally clustered near the particle surface, good resolution is obtained in the regions where the gradients of relevant flow variables are most significant. This coordinate system also allows large domain sizes with a reasonable number of mesh points to simulate unbounded fluid around a particle. Changing the aspect ratio of the inner computational boundary enables simulations of different particle shapes ranging from a sphere to a slender fiber. Numerical studies of the latter particle shape allow testing of slender body theories. The mass and momentum equations are solved with a Schur complement approach allowing us to solve the zero inertia case necessary to isolate the viscoelastic effects. The singularities associated with the coordinate system are overcome using L'Hopital's rule. A straightforward imposition of conditions representing a time-varying combination of linear flows on the outer boundary allows us to study various flows with the same computational domain geometry. {For the special but important case of zero fluid and particle inertia we obtain a novel formulation that satisfies the force- and torque-free constraint in an iteration-free manner.} The numerical method is demonstrated for various flows of Newtonian and viscoelastic fluids around spheres and spheroids (including those with large aspect ratio). Good agreement is demonstrated with existing theoretical and numerical results.

This study investigates the hydrodynamics of droplet formation in a T-shaped cylindrical microfluidic device using micro-PIV experiments and CFD simulations. Devices of 150 micro-m internal diameter were fabricated from PDMS via a cost-effective embedded templating method. Flow visualization was conducted using immiscible silicone oil and deionized water, forming water-in-oil droplets. A mathematical model coupling the Navier-Stokes and conservative level-set equations was solved using the finite element method. Detailed flow fields (velocity, pressure, and phase distribution) were obtained over a wide range of flow-rate ratios (0.1-10) and capillary numbers (0.001-0.1) to characterize droplet formation mechanisms. Phase evolution revealed distinct breakup stages (lag, filling, necking, and pinch-off) and multiple regimes (squeezing, dripping, sausage flow, and parallel flow with tip streaming). A regime map delineating droplet and non-droplet regions was developed. Droplet size, curvature, and internal flow profiles exhibited strong dependence on Ca and Qr. Scaling analysis showed linear dependence of droplet size on Qr in the squeezing regime, with curvature nearly independent of Qr. In contrast, both size and curvature followed power-law dependence on Ca and Qr in the dripping regime. Velocity fields inside droplets were laminar and parabolic in the core. Fully developed plug-like profiles appeared in squeezing, whereas front and rear regions remained developing in dripping. Correlations for droplet length, curvature, and film thickness, including a novel thin-film model incorporating visco-inertial and capillary effects, enable predictive design within the studied range. These findings advance fundamental understanding of confined droplet dynamics and provide quantitative guidelines for optimizing droplet-based microfluidic systems.

Generative models such as denoising diffusion models are quickly advancing their ability to approximate highly complex data distributions. They are also increasingly leveraged in scientific machine learning, where samples from the implied data distribution are expected to adhere to specific governing equations. We present a framework that unifies generative modeling and partial differential equation fulfillment by introducing a first-principle-based loss term that enforces generated samples to fulfill the underlying physical constraints. Our approach reduces the residual error by up to two orders of magnitude compared to previous work in a fluid flow case study and outperforms task-specific frameworks in relevant metrics for structural topology optimization. We also present numerical evidence that our extended training objective acts as a natural regularization mechanism against overfitting. Our framework is simple to implement and versatile in its applicability for imposing equality and inequality constraints as well as auxiliary optimization objectives.

In this paper, we rigorously derive the fundamental PDEs of fluid mechanics, such as the compressible Euler and incompressible Navier-Stokes-Fourier equations, starting from the hard sphere particle systems undergoing elastic collisions. This resolves Hilbert's sixth problem, as it pertains to the program of deriving the fluid equations from Newton's laws by way of Boltzmann's kinetic theory. The proof relies on the derivation of Boltzmann's equation on 2D and 3D tori, which is an extension of our previous work (arXiv:2408.07818).

We demonstrate several techniques to encourage practical uses of neural networks for fluid flow estimation. In the present paper, three perspectives which are remaining challenges for applications of machine learning to fluid dynamics are considered: 1. interpretability of machine-learned results, 2. bulking out of training data, and 3. generalizability of neural networks. For the interpretability, we first demonstrate two methods to observe the internal procedure of neural networks, i.e., visualization of hidden layers and application of gradient-weighted class activation mapping (Grad-CAM), applied to canonical fluid flow estimation problems -- (1) drag coefficient estimation of a cylinder wake and (2) velocity estimation from particle images. It is exemplified that both approaches can successfully tell us evidences of the great capability of machine learning-based estimations. We then utilize some techniques to bulk out training data for super-resolution analysis and temporal prediction for cylinder wake and NOAA sea surface temperature data to demonstrate that sufficient training of neural networks with limited amount of training data can be achieved for fluid flow problems. The generalizability of machine learning model is also discussed by accounting for the perspectives of inter/extrapolation of training data, considering super-resolution of wakes behind two parallel cylinders. We find that various flow patterns generated by complex interaction between two cylinders can be reconstructed well, even for the test configurations regarding the distance factor. The present paper can be a significant step toward practical uses of neural networks for both laminar and turbulent flow problems.

We consider the convected Helmholtz equation modeling linear acoustic propagation at a fixed frequency in a subsonic flow around a scattering object. The flow is supposed to be uniform in the exterior domain far from the object, and potential in the interior domain close to the object. Our key idea is the reformulation of the original problem using the Prandtl--Glauert transformation on the whole flow domain, yielding (i) the classical Helmholtz equation in the exterior domain and (ii) an anisotropic diffusive PDE with skew-symmetric first-order perturbation in the interior domain such that its transmission condition at the coupling boundary naturally fits the Neumann condition from the classical Helmholtz equation. Then, efficient off-the-shelf tools can be used to perform the BEM-FEM coupling, leading to two novel variational formulations for the convected Helmholtz equation. The first formulation involves one surface unknown and can be affected by resonant frequencies, while the second formulation avoids resonant frequencies and involves two surface unknowns. Numerical simulations are presented to compare the two formulations.

Rectified flow and reflow procedures have significantly advanced fast generation by progressively straightening ordinary differential equation (ODE) flows. They operate under the assumption that image and noise pairs, known as couplings, can be approximated by straight trajectories with constant velocity. However, we observe that modeling with constant velocity and using reflow procedures have limitations in accurately learning straight trajectories between pairs, resulting in suboptimal performance in few-step generation. To address these limitations, we introduce Constant Acceleration Flow (CAF), a novel framework based on a simple constant acceleration equation. CAF introduces acceleration as an additional learnable variable, allowing for more expressive and accurate estimation of the ODE flow. Moreover, we propose two techniques to further improve estimation accuracy: initial velocity conditioning for the acceleration model and a reflow process for the initial velocity. Our comprehensive studies on toy datasets, CIFAR-10, and ImageNet 64x64 demonstrate that CAF outperforms state-of-the-art baselines for one-step generation. We also show that CAF dramatically improves few-step coupling preservation and inversion over Rectified flow. Code is available at https://github.com/mlvlab/CAF{https://github.com/mlvlab/CAF}.

In this work, we introduce an efficient generation procedure to produce synthetic multi-modal datasets of fluid simulations. The procedure can reproduce the dynamics of fluid flows and allows for exploring and learning various properties of their complex behavior, from distinct perspectives and modalities. We employ our framework to generate a set of thoughtfully designed training datasets, which attempt to span specific fluid simulation scenarios in a meaningful way. The properties of our contributions are demonstrated by evaluating recently published algorithms for the neural fluid simulation and fluid inverse rendering tasks using our benchmark datasets. Our contribution aims to fulfill the community's need for standardized training data, fostering more reproducibile and robust research.

Predicting flows that occur both through and around porous bodies is challenging due to coupled physics across fluid and porous regions and the need to generalize across diverse geometries and boundary conditions. We address this problem using two Physics Informed learning approaches: Physics Informed PointNets (PIPN) and Physics Informed Geometry Aware Neural Operator (P-IGANO). We enforce the incompressible Navier Stokes equations in the free-flow region and a Darcy Forchheimer extension in the porous region within a unified loss and condition the networks on geometry and material parameters. Datasets are generated with OpenFOAM on 2D ducts containing porous obstacles and on 3D windbreak scenarios with tree canopies and buildings. We first verify the pipeline via the method of manufactured solutions, then assess generalization to unseen shapes, and for PI-GANO, to variable boundary conditions and parameter settings. The results show consistently low velocity and pressure errors in both seen and unseen cases, with accurate reproduction of the wake structures. Performance degrades primarily near sharp interfaces and in regions with large gradients. Overall, the study provides a first systematic evaluation of PIPN/PI-GANO for simultaneous through-and-around porous flows and shows their potential to accelerate design studies without retraining per geometry.

Hypothesis: Bacterial contamination of surfaces poses a major threat to public health. Designing effective antibacterial or self-cleaning surfaces requires understanding how bacteria-laden droplets interact with solid substrates and how readily they can be removed. We hypothesize that bacterial motility critically influences the early-stage surface interaction (i.e., surface adhesion) of bacteria-laden droplets, which cannot be captured by conventional contact angle goniometry. Experiments: Sessile droplets containing live and dead Escherichia coli (E. coli) were studied to probe their wetting and interfacial behavior. Contact angle goniometry was used to probe dynamic wetting, while a cantilever-deflection-based method was used to quantify adhesion. Internal flow dynamics were visualized using micro-particle image velocimetry (PIV) and analyzed statistically. Complementary sliding experiments on moderately wettable substrates were performed to assess contact line mobility under tilt. Findings: Despite lower surface tension, droplets containing live bacteria exhibited lower surface adhesion forces than their dead counterparts, with adhesion further decreasing at higher bacterial concentrations. Micro-PIV revealed that flagellated live E. coli actively resist evaporation-driven capillary flow via upstream migration, while at higher concentrations, collective dynamics emerge, producing spatially coherent bacterial motion despite temporal variability. These coordinated flows disrupt passive transport and promote depinning of the contact line, thereby reducing adhesion. Sliding experiments confirmed enhanced contact line mobility and frequent stick-slip motion in live droplets, even with lower receding contact angles and higher hysteresis. These findings provide mechanistic insight into droplet retention, informing the design of self-cleaning/antifouling surfaces.

Modeling the mechanics of fluid in complex scenes is vital to applications in design, graphics, and robotics. Learning-based methods provide fast and differentiable fluid simulators, however most prior work is unable to accurately model how fluids interact with genuinely novel surfaces not seen during training. We introduce SURFSUP, a framework that represents objects implicitly using signed distance functions (SDFs), rather than an explicit representation of meshes or particles. This continuous representation of geometry enables more accurate simulation of fluid-object interactions over long time periods while simultaneously making computation more efficient. Moreover, SURFSUP trained on simple shape primitives generalizes considerably out-of-distribution, even to complex real-world scenes and objects. Finally, we show we can invert our model to design simple objects to manipulate fluid flow.

Capillary-driven transport offers a simple, self-sustained alternative to externally pumped microfluidic systems, yet achieving precise control of such flows remains challenging. We experimentally and theoretically investigate capillary flow in rectangular microchannels when a liquid meniscus encounters a geometric step with varying channel width and height. Depending on the contact angle and step dimensions, the meniscus either pins or advances, defining distinct flow and no-flow regimes. Introducing a lateral offset between channel sidewalls provides an additional geometric control that enables reversible switching from a pinned to a flowing state, even for liquids with relatively high contact angles. We rationalize these transitions using numerical simulations and an energy-based scaling model that captures the balance between surface tension and Laplace pressure at the step. Finally, we demonstrate synchronization of capillary fronts in parallel microchannels by combining stepped and offset geometries. These results establish a simple, geometry-mediated mechanism for passive control and synchronization of capillary flows, expanding the design space for microfluidic systems.

We propose PROSE-FD, a zero-shot multimodal PDE foundational model for simultaneous prediction of heterogeneous two-dimensional physical systems related to distinct fluid dynamics settings. These systems include shallow water equations and the Navier-Stokes equations with incompressible and compressible flow, regular and complex geometries, and different buoyancy settings. This work presents a new transformer-based multi-operator learning approach that fuses symbolic information to perform operator-based data prediction, i.e. non-autoregressive. By incorporating multiple modalities in the inputs, the PDE foundation model builds in a pathway for including mathematical descriptions of the physical behavior. We pre-train our foundation model on 6 parametric families of equations collected from 13 datasets, including over 60K trajectories. Our model outperforms popular operator learning, computer vision, and multi-physics models, in benchmark forward prediction tasks. We test our architecture choices with ablation studies.

While the generation of 3D content from single-view images has been extensively studied, the creation of physically consistent 3D dynamic scenes from videos remains in its early stages. We propose a novel framework leveraging generative 3D Gaussian Splatting (3DGS) models to extract and re-simulate 3D dynamic fluid objects from single-view videos using simulation methods. The fluid geometry represented by 3DGS is initially generated and optimized from single-view images, then denoised, densified, and aligned across frames. We estimate the fluid surface velocity using optical flow, propose a mainstream extraction algorithm to refine it. The 3D volumetric velocity field is then derived from the velocity of the fluid's enclosed surface. The velocity field is therewith converted into a divergence-free, grid-based representation, enabling the optimization of simulation parameters through its differentiability across frames. This process outputs simulation-ready fluid assets with physical dynamics closely matching those observed in the source video. Our approach is applicable to various liquid fluids, including inviscid and viscous types, and allows users to edit the output geometry or extend movement durations seamlessly. This automatic method for creating 3D dynamic fluid assets from single-view videos, easily obtainable from the internet, shows great potential for generating large-scale 3D fluid assets at a low cost.

Flow matching generates data by integrating a learned velocity field, where the number of integration steps (NFE) directly determines inference cost. We analyze which properties of the velocity field govern integration error by decomposing the velocity Jacobian into its symmetric part S (strain rate) and antisymmetric part Omega (vorticity). We prove that strain and vorticity play different roles: strain controls exponential error amplification through the logarithmic norm, while vorticity contributes only linearly to the local truncation error. We further show that the optimal transport velocity field is irrotational and has zero material derivative, implying second-order Euler accuracy; for exact displacement interpolation, the associated Lagrangian particle dynamics are integrated exactly by Euler. Motivated by this analysis, we study weighted Jacobian regularization with strain weight alpha and vorticity weight beta. Experiments on 2D synthetic data confirm the main theoretical predictions, showing up to 2.7x lower integration error at NFE=5. Preliminary CIFAR-10 experiments show consistent trends, with a lightweight fine-tuning procedure improving FID by 14 percent at NFE=10 while preserving high-NFE quality.

The aim of the present work is to investigate the influence of the realistic model parameters on the equipartition of energy in a vibrofluidized system. To achieve this, a three-dimensional vertically vibrated granular system consisting of spherical particles is simulated using the discrete element method (DEM) using the open-source software LAMMPS. Interparticle and wall-particle interactions are determined using the linear-spring dashpot model. Simulations are performed for nearly perfectly smooth to nearly perfectly rough particles. Two different values for the ratio of the tangential to normal spring stiffness coefficient kappa (2/7 and 3/4) are chosen. Non-equipartition of energy between the translational and rotational modes is observed for all realistic values in the parametric range.

Biological tissues exhibit complex behaviors with their dynamics often resembling inert soft matter such as liquids, polymers, colloids, and liquid crystals. These analogies enable physics-based approaches for investigations of emergent behaviors in biological processes. A well-studied case is the spreading of cellular aggregates on solid surfaces, where they display dynamics similar to viscous droplets. In vivo, however, cells and tissues are in a confined environment with varying geometries and mechanical properties to which they need to adapt. In this work, we compressed cellular aggregates between two solid surfaces and studied their dynamics using microscopy, and computer simulations. The confined cellular aggregates transitioned from compressed spheres into dynamic living capillary bridges exhibiting bridge thinning and a convex-to-concave meniscus curvature transition. We found that the stability of the bridge is determined by the interplay between cell growth and cell spreading on the confining surfaces. This interaction leads to bridge rupture at a critical length scale determined by the distance between the plates. The force distributions, formation and stability regimes of the living capillary bridges were characterized with full 3D computer simulations that included cell division, migration and growth dynamics, directly showing how mechanical principles govern the behavior of the living bridges; cellular aggregates display jamming and stiffening analogously to granular matter, and cell division along the long axis enhances thinning. Based on our results, we propose a new class of active soft matter behavior, where cellular aggregates exhibit liquid-like adaptation to confinement, but with self-organized rupturing driven by biological activity.

We develop a deep reinforcement learning method for training a jellyfish-like swimmer to effectively track a moving target in a two-dimensional flow. This swimmer is a flexible object equipped with a muscle model based on torsional springs. We employ a deep Q-network (DQN) that takes the swimmer's geometry and dynamic parameters as inputs, and outputs actions which are the forces applied to the swimmer. In particular, we introduce an action regulation to mitigate the interference from complex fluid-structure interactions. The goal of these actions is to navigate the swimmer to a target point in the shortest possible time. In the DQN training, the data on the swimmer's motions are obtained from simulations conducted using the immersed boundary method. During tracking a moving target, there is an inherent delay between the application of forces and the corresponding response of the swimmer's body due to hydrodynamic interactions between the shedding vortices and the swimmer's own locomotion. Our tests demonstrate that the swimmer, with the DQN agent and action regulation, is able to dynamically adjust its course based on its instantaneous state. This work extends the application scope of machine learning in controlling flexible objects within fluid environments.

Normalizing flows are a promising tool for modeling probability distributions in physical systems. While state-of-the-art flows accurately approximate distributions and energies, applications in physics additionally require smooth energies to compute forces and higher-order derivatives. Furthermore, such densities are often defined on non-trivial topologies. A recent example are Boltzmann Generators for generating 3D-structures of peptides and small proteins. These generative models leverage the space of internal coordinates (dihedrals, angles, and bonds), which is a product of hypertori and compact intervals. In this work, we introduce a class of smooth mixture transformations working on both compact intervals and hypertori. Mixture transformations employ root-finding methods to invert them in practice, which has so far prevented bi-directional flow training. To this end, we show that parameter gradients and forces of such inverses can be computed from forward evaluations via the inverse function theorem. We demonstrate two advantages of such smooth flows: they allow training by force matching to simulation data and can be used as potentials in molecular dynamics simulations.

Traditional experimental and numerical approaches for fluid dynamics problems often suffer from high computational cost, mesh sensitivity, and limited capability in capturing complex physical behaviors. Moreover, conventional physics-informed neural networks (PINNs) frequently struggle in chaotic and highly unsteady flow regimes. In this work, we propose PhysicsFormer, a fast and efficient transformer-based physics-informed framework that incorporates multi-head encoder-decoder cross-attention. Unlike multilayer perceptron-based PINNs, PhysicsFormer operates on sequential representations constructed from spatio-temporal data, enabling effective learning of long-range temporal dependencies and improved propagation of initial condition information. A data-embedding strategy is employed to convert spatio-temporal points into pseudo-sequences, while a dynamics-weighted loss function replaces the standard PINNs formulation. Owing to its parallel learning structure, PhysicsFormer demonstrates superior computational efficiency compared to existing transformer-based approaches. The framework is validated on Burgers' equation and flow reconstruction governed by the Navier-Stokes equations, achieving mean squared errors on the order of 10^{-6}. In addition, an inverse problem involving parameter identification in the two-dimensional incompressible Navier-Stokes equations is investigated. For clean data, PhysicsFormer achieves zero identification error for both λ_1 and λ_2; under 1% Gaussian noise, the errors are 0.07% for λ_1 and 0% for λ_2. These results demonstrate that PhysicsFormer provides a reliable and computationally efficient surrogate modeling framework for time-dependent fluid flow problems.

In recent years, Physics-Informed Neural Networks (PINNs) have emerged as a powerful and robust framework for solving nonlinear differential equations across a wide range of scientific and engineering disciplines, including biology, geophysics, astrophysics and fluid dynamics. In the PINN framework, the governing partial differential equations, along with initial and boundary conditions, are encoded directly into the loss function, enabling the network to learn solutions that are consistent with the underlying physics. In this work, we employ the PINN framework to solve the dimensionless Navier-Stokes equations for three two-dimensional incompressible, steady, laminar flow problems without using any labeled data. The boundary and initial conditions are enforced in a hard manner, ensuring they are satisfied exactly rather than penalized during training. We validate the PINN predicted velocity profiles, drag coefficients and pressure profiles against the conventional computational fluid dynamics (CFD) simulations for moderate to high values of Reynolds number (Re). It is observed that the PINN predictions show good agreement with the CFD results at lower Re. We also extend our analysis to a transient condition and find that our method is equally capable of simulating complex time-dependent flow dynamics. To quantitatively assess the accuracy, we compute the L_2 normalized error, which lies in the range O(10^{-4}) - O(10^{-1}) for our chosen case studies.

Physics-informed surrogate models can accelerate computational fluid dynamics simulations. However, many existing methods reproduce global flow patterns more reliably than localized multiscale structures. This study presents a physics-informed Fourier-wavelet transformer for next-step velocity-field reconstruction in real-world flow benchmarks. The proposed formulation combines hybrid Fourier-wavelet spectral encoding with physics-biased self-attention based on partial differential equation residual diagnostics. It also uses self-supervised pretraining through Masked Physics Prediction and Equation Consistency Prediction. The experiments are conducted on two real benchmark cases: cylinder-wake flow and fluid-structure interaction. All approaches are evaluated under a shared local protocol and compared with spectral, transformer-based, operator-learning, and physics-informed neural-network baselines. On the cylinder-wake benchmark, the proposed model achieves the best aggregate accuracy, with an all-channel normalized mean-squared error of 0.05875 and an all-channel Pearson correlation coefficient of 0.97019. On the fluid-structure-interaction benchmark, it gives the lowest all-channel normalized mean-squared error of 2.70 times 10^{-4}, compared with 4.02 times 10^{-4} for the strongest baseline. Component-wise field comparisons and scale-separated diagnostics further show stronger recovery of localized wake structures, including near-body, wake-core, and far-wake features. The results demonstrate improved real-world flow reconstruction while maintaining a practical accuracy-cost tradeoff.

In this paper, we propose a { P_{1}^{c}}RT0-P0 discretization of the Stokes equations on general simplicial meshes in two/three dimensions (2D/3D), which yields an exactly divergence-free and pressure-independent velocity approximation with optimal order. Our method has the following features. Firstly, the global number of the degrees of freedom of our method is the same as the low order Bernardi and Raugel (B-R) finite element method (Bernardi and Raugel, 1985), while the number of {the non-zero entries} of the former is about half of the latter in the velocity-velocity region of the coefficient matrix. Secondly, the { P_{1}^{c}} component of the velocity, the RT0 component of the velocity and the pressure seem to solve a popular { P_{1}^{c}}-{RT0}-P0 discretization of a poroelastic-type system formally. Finally, our method can be easily transformed into a pressure-robust and stabilized { P_{1}^{c}}-P0 discretization for the Stokes problem via the static condensation of the RT0 component, which has a much smaller number of global degrees of freedom. Numerical experiments illustrating the robustness of our method are also provided.

Generative machine learning methods, such as diffusion models and flow matching, have shown great potential in modeling complex system behaviors and building efficient surrogate models. However, these methods typically learn the underlying physics implicitly from data. We propose Physics-Based Flow Matching (PBFM), a novel generative framework that explicitly embeds physical constraints, both PDE residuals and algebraic relations, into the flow matching objective. We also introduce temporal unrolling at training time that improves the accuracy of the final, noise-free sample prediction. Our method jointly minimizes the flow matching loss and the physics-based residual loss without requiring hyperparameter tuning of their relative weights. Additionally, we analyze the role of the minimum noise level, sigma_{min}, in the context of physical constraints and evaluate a stochastic sampling strategy that helps to reduce physical residuals. Through extensive benchmarks on three representative PDE problems, we show that our approach yields up to an 8times more accurate physical residuals compared to FM, while clearly outperforming existing algorithms in terms of distributional accuracy. PBFM thus provides a principled and efficient framework for surrogate modeling, uncertainty quantification, and accelerated simulation in physics and engineering applications.

Safe yet stable grasping requires a robotic hand to apply sufficient force on the object to immobilize it while keeping it from getting damaged. Soft robotic hands have been proposed for safe grasping due to their passive compliance, but even such a hand can crush objects if the applied force is too high. Thus for safe grasping, regulating the grasping force is of uttermost importance even with soft hands. In this work, we present a force controlled soft hand and use it to achieve safe grasping. To this end, resistive force and bend sensors are integrated in a soft hand, and a data-driven calibration method is proposed to estimate contact interaction forces. Given the force readings, the pneumatic pressures are regulated using a proportional-integral controller to achieve desired force. The controller is experimentally evaluated and benchmarked by grasping easily deformable objects such as plastic and paper cups without neither dropping nor deforming them. Together, the results demonstrate that our force controlled soft hand can grasp deformable objects in a safe yet stable manner.

We present a self-supervised framework for learning implicit 3D physical dynamics directly from video-derived supervisory signals. While current generative video models achieve high visual fidelity, they lack a 3D geometric foundation, often resulting in physical inconsistencies and a failure to maintain object permanence. We address this by shifting the predictive bottleneck from 2D image space to a `lifted' 3D Volumetric Latent Space. Our method unprojects semantic features from a Video Joint-Embedding Predictive Architecture (V-JEPA) into a voxelized grid, grounded by monocular depth priors. This lifting enables a Volumetric Feature Advection to learn an action-conditioned transition operator that treats physics as a spatio-temporal state advection problem, i.e., learn implicit 3D physics. Unlike state-of-the-art hybrid models that rely on explicit classical simulators for training and/or inference, our architecture tracks material states implicitly within high-dimensional V-JEPA features. This allows for the emergent simulation of heterogeneous phenomena (e.g., rigid body motion in fluid flow) within a single, unified pipeline. Supervised solely via end-to-end video-derived signal plus action conditions, without access to physics engine internal states, labels, or surrogate models, our model demonstrates good long-term structural stability and physical plausibility on multiple benchmarks (CLEVERER, PhysInOne, PhysGaia). We believe that this work opens a scalable pathway toward general-purpose dynamic world models that internalize the 3D invariants of the physical world solely through passive observation of monocular videos.

Learning-based simulation of multi-object rigid-body dynamics remains difficult because contact is discontinuous and errors compound over long horizons. Most existing methods remain tied to mesh connectivity and vertex-level message passing, which limits their applicability to mesh-free inputs such as point clouds and leads to high computational cost. Efficiently modeling high-fidelity rigid-body dynamics from mesh-free representations, therefore, remains challenging. We introduce RigidFormer, an object-centric Transformer-based model that learns mesh-free rigid-body dynamics with controllable integration step sizes. RigidFormer reasons at the object level and advances each object through compact anchors; Anchor-Vertex Pooling enriches these anchors with local vertex features, retaining contact-relevant geometry without dense vertex-level interaction. We propose Anchor-based RoPE to inject anchor geometry into attention while respecting the unordered nature of objects and anchors: object-token processing is permutation-equivariant, and the mean-pooled anchor descriptor is invariant to anchor reindexing while preserving shape extent. RigidFormer further enforces rigidity by projecting updates onto the rigid-body manifold using differentiable Kabsch alignment. On standard benchmarks, RigidFormer outperforms or matches mesh-based baselines using point inputs, runs faster, generalizes to unseen point resolutions and across datasets, and scales to 200+ objects; we also show a preliminary extension to command-conditioned articulated bodies by treating body parts as interacting object-level components.

Achieving a desired impedance during physical interaction remains a central problem in compliant control. In many practical implementations, admittance control combined with linear position controllers is employed, but this structure typically results in only approximate impedance behavior. This paper establishes a rigorous equivalence between the impedance realization problem and the generalized output regulation theory, and shows that, under the admittance architecture and assuming the inner position controller is restricted to linear combinations of commonly used signals, a unique control law exists that achieves exact compliant control. The resulting controller introduces additional terms with respect to a conventional PD formulation, while preserving a simple structure. Numerical simulations are used to illustrate the effectiveness of the proposed approach under nominal conditions and in the presence of model uncertainties, and to compare its performance against a standard PD controller. The results demonstrate improved interaction performance and robustness, supporting the theoretical analysis.

We introduce PhysGaia, a novel physics-aware benchmark for Dynamic Novel View Synthesis (DyNVS) that encompasses both structured objects and unstructured physical phenomena. While existing datasets primarily focus on photorealistic appearance, PhysGaia is specifically designed to support physics-consistent dynamic reconstruction. Our benchmark features complex scenarios with rich multi-body interactions, where objects realistically collide and exchange forces. Furthermore, it incorporates a diverse range of materials, including liquid, gas, textile, and rheological substance, moving beyond the rigid-body assumptions prevalent in prior work. To ensure physical fidelity, all scenes in PhysGaia are generated using material-specific physics solvers that strictly adhere to fundamental physical laws. We provide comprehensive ground-truth information, including 3D particle trajectories and physical parameters (e.g., viscosity), enabling the quantitative evaluation of physical modeling. To facilitate research adoption, we also provide integration pipelines for recent 4D Gaussian Splatting models along with our dataset and their results. By addressing the critical shortage of physics-aware benchmarks, PhysGaia can significantly advance research in dynamic view synthesis, physics-based scene understanding, and the integration of deep learning with physical simulation, ultimately enabling more faithful reconstruction and interpretation of complex dynamic scenes.

It is well known that the reversibility of Stokes flow makes it difficult for small microorganisms to swim. Inertial effects break this reversibility, allowing new mechanisms of propulsion and feeding. Therefore it is important to understand the effects of unsteady and fluid inertia on the dynamics of microorganisms in flow. In this work, we show how to translate known inertial effects for non-motile organisms to motile ones, from passive to active particles. The method relies on a principle used earlier by Legendre and Magnaudet (1997) to deduce inertial corrections to the lift force on a bubble from the inertial drag on a solid sphere, using the fact that small inertial effects are determined by the far field of the disturbance flow. The method allows for example to compute the inertial effect of unsteady fluid accelerations on motile organisms, and the inertial forces such organisms experience in steady shear flow. We explain why the method fails to describe the effect of convective fluid inertia.

We study the Cauchy problem for the one-dimensional isothermal compressible Navier--Stokes system with the van der Waals equation of state, and analyze the well-posedness and asymptotic stability of steady-state phase-transition solutions at subcritical temperatures. Working in Lagrangian coordinates, we use variational techniques to construct piecewise smooth steady-state solutions corresponding to two-phase equilibrium states under finite-mass perturbations. Introducing artificial-viscosity regularization, we first establish existence of the global minimizer of the regularized variational problem, unique within each fixed symmetry class; passing to the vanishing artificial-viscosity limit then yields a physically admissible steady-state solution with two phase interfaces. For initial perturbations that are small with respect to energy, piecewise-gradient, total-variation, and integral norms but may exhibit large pointwise jumps across phase boundaries, we derive uniform a priori bounds for weak solutions near the two-phase equilibrium profile. We further prove that these global weak solutions converge to the steady-state two-phase equilibrium in L^infty(R) as ttoinfty, thereby characterizing their large-time asymptotic behavior. Physically, finite mass perturbations break the uniqueness of the uniform steady state and generate infinitely many piecewise constant two-phase equilibria satisfying the Maxwell equal-area rule. Artificial viscosity acts as a selection principle that singles out the physically relevant two-interface steady-state configuration, and this two-phase equilibrium is asymptotically stable under small integral perturbations that allow large-amplitude discontinuities at phase interfaces.

Focusing on simulated dilute polymer solutions, this letter investigates the interactions between flow structures and organized polymer stress sheets for the steady arrowhead coherent structure in a two-dimensional periodic channel flow. Formulating the problem in a frame of reference moving with the arrowhead velocity, streamlines, which are also pathlines in this frame, enables the identification of two distinct topological regions linked to two stagnation points. The streamlines help connecting the spatial distribution of polymer stress within the sheets and the dynamics of polymers transported by the flow. Using stresslines, lines parallel to the eigenvectors of polymer stress, a novel formulation of the viscoelastic stress term in the momentum transport equation proposes a more intuitive interpretation of the relation between the curvature of the stresslines, and the variation of stress along these lines, with the local flow topology. An approximation of this formulation is shown to explain the pressure jump observed in the arrowhead structure as a function of the local curvature of the polymer stress sheet.

In this paper, we address the problem of tactile sim-to-real policy transfer for contact-rich tasks. Existing methods primarily focus on vision-based sensors and emphasize image rendering quality while providing overly simplistic models of force and shear. Consequently, these models exhibit a large sim-to-real gap for many dexterous tasks. Here, we present HydroShear, a non-holonomic hydroelastic tactile simulator that advances the state-of-the-art by modeling: a) stick-slip transitions, b) path-dependent force and shear build up, and c) full SE(3) object-sensor interactions. HydroShear extends hydroelastic contact models using Signed Distance Functions (SDFs) to track the displacements of the on-surface points of an indenter during physical interaction with the sensor membrane. Our approach generates physics-based, computationally efficient force fields from arbitrary watertight geometries while remaining agnostic to the underlying physics engine. In experiments with GelSight Minis, HydroShear more faithfully reproduces real tactile shear compared to existing methods. This fidelity enables zero-shot sim-to-real transfer of reinforcement learning policies across four tasks: peg insertion, bin packing, book shelving for insertion, and drawer pulling for fine gripper control under slip. Our method achieves a 93% average success rate, outperforming policies trained on tactile images (34%) and alternative shear simulation methods (58%-61%).

Solving partial differential equations (PDEs) with machine learning has recently attracted great attention, as PDEs are fundamental tools for modeling real-world systems that range from fundamental physical science to advanced engineering disciplines. Most real-world physical systems across various disciplines are actually involved in multiple coupled physical fields rather than a single field. However, previous machine learning studies mainly focused on solving single-field problems, but overlooked the importance and characteristics of multiphysics problems in real world. Multiphysics PDEs typically entail multiple strongly coupled variables, thereby introducing additional complexity and challenges, such as inter-field coupling. Both benchmarking and solving multiphysics problems with machine learning remain largely unexamined. To identify and address the emerging challenges in multiphysics problems, we mainly made three contributions in this work. First, we collect the first general multiphysics dataset, the Multiphysics Bench, that focuses on multiphysics PDE solving with machine learning. Multiphysics Bench is also the most comprehensive PDE dataset to date, featuring the broadest range of coupling types, the greatest diversity of PDE formulations, and the largest dataset scale. Second, we conduct the first systematic investigation on multiple representative learning-based PDE solvers, such as PINNs, FNO, DeepONet, and DiffusionPDE solvers, on multiphysics problems. Unfortunately, naively applying these existing solvers usually show very poor performance for solving multiphysics. Third, through extensive experiments and discussions, we report multiple insights and a bag of useful tricks for solving multiphysics with machine learning, motivating future directions in the study and simulation of complex, coupled physical systems.

We present rectified flow, a surprisingly simple approach to learning (neural) ordinary differential equation (ODE) models to transport between two empirically observed distributions \pi_0 and \pi_1, hence providing a unified solution to generative modeling and domain transfer, among various other tasks involving distribution transport. The idea of rectified flow is to learn the ODE to follow the straight paths connecting the points drawn from \pi_0 and \pi_1 as much as possible. This is achieved by solving a straightforward nonlinear least squares optimization problem, which can be easily scaled to large models without introducing extra parameters beyond standard supervised learning. The straight paths are special and preferred because they are the shortest paths between two points, and can be simulated exactly without time discretization and hence yield computationally efficient models. We show that the procedure of learning a rectified flow from data, called rectification, turns an arbitrary coupling of \pi_0 and \pi_1 to a new deterministic coupling with provably non-increasing convex transport costs. In addition, recursively applying rectification allows us to obtain a sequence of flows with increasingly straight paths, which can be simulated accurately with coarse time discretization in the inference phase. In empirical studies, we show that rectified flow performs superbly on image generation, image-to-image translation, and domain adaptation. In particular, on image generation and translation, our method yields nearly straight flows that give high quality results even with a single Euler discretization step.

We propose Geometric Clifford Algebra Networks (GCANs) for modeling dynamical systems. GCANs are based on symmetry group transformations using geometric (Clifford) algebras. We first review the quintessence of modern (plane-based) geometric algebra, which builds on isometries encoded as elements of the Pin(p,q,r) group. We then propose the concept of group action layers, which linearly combine object transformations using pre-specified group actions. Together with a new activation and normalization scheme, these layers serve as adjustable geometric templates that can be refined via gradient descent. Theoretical advantages are strongly reflected in the modeling of three-dimensional rigid body transformations as well as large-scale fluid dynamics simulations, showing significantly improved performance over traditional methods.

We present a flow-based approach to the optimal transport (OT) problem between two continuous distributions pi_0,pi_1 on R^d, of minimizing a transport cost E[c(X_1-X_0)] in the set of couplings (X_0,X_1) whose marginal distributions on X_0,X_1 equals pi_0,pi_1, respectively, where c is a cost function. Our method iteratively constructs a sequence of neural ordinary differentiable equations (ODE), each learned by solving a simple unconstrained regression problem, which monotonically reduce the transport cost while automatically preserving the marginal constraints. This yields a monotonic interior approach that traverses inside the set of valid couplings to decrease the transport cost, which distinguishes itself from most existing approaches that enforce the coupling constraints from the outside. The main idea of the method draws from rectified flow, a recent approach that simultaneously decreases the whole family of transport costs induced by convex functions c (and is hence multi-objective in nature), but is not tailored to minimize a specific transport cost. Our method is a single-object variant of rectified flow that guarantees to solve the OT problem for a fixed, user-specified convex cost function c.

Simulating fluid flow around arbitrary shapes is key to solving various engineering problems. However, simulating flow physics across complex geometries remains numerically challenging and computationally resource-intensive, particularly when using conventional PDE solvers. Machine learning methods offer attractive opportunities to create fast and adaptable PDE solvers. However, benchmark datasets to measure the performance of such methods are scarce, especially for flow physics across complex geometries. We introduce FlowBench, a dataset for neural simulators with over 10K samples, which is currently larger than any publicly available flow physics dataset. FlowBench contains flow simulation data across complex geometries (parametric vs. non-parametric), spanning a range of flow conditions (Reynolds number and Grashoff number), capturing a diverse array of flow phenomena (steady vs. transient; forced vs. free convection), and for both 2D and 3D. FlowBench contains over 10K data samples, with each sample the outcome of a fully resolved, direct numerical simulation using a well-validated simulator framework designed for modeling transport phenomena in complex geometries. For each sample, we include velocity, pressure, and temperature field data at 3 different resolutions and several summary statistics features of engineering relevance (such as coefficients of lift and drag, and Nusselt numbers). %Additionally, we include masks and signed distance fields for each shape. We envision that FlowBench will enable evaluating the interplay between complex geometry, coupled flow phenomena, and data sufficiency on the performance of current, and future, neural PDE solvers. We enumerate several evaluation metrics to help rank order the performance of neural PDE solvers. We benchmark the performance of several baseline methods including FNO, CNO, WNO, and DeepONet.

In this paper, we revisit the joint low-Mach and low-Frode number limit for the compressible Navier-Stokes equations with degenerate, density-dependent viscosity. Employing the relative entropy framework based on the concept of κ-entropy, we rigorously justify the convergence of weak solutions toward the generalized anelastic system in a three-dimensional periodic domain for well-prepared initial data. For general ill-prepared initial data, we establish a similar convergence result in the whole space, relying essentially on dispersive estimates for acoustic waves. Compared with the work of Fanelli and Zatorska [Commun. Math. Phys., 400 (2023), pp. 1463-1506], our analysis is conducted for the standard isentropic pressure law, thereby eliminating the need for the cold pressure term that played a crucial role in the previous approach. To the best of our knowledge, this is the first rigorous singular limit result for the compressible Navier-Stokes equations with degenerate viscosity that requires no additional regularization of the system.

We introduce a new family of physics-inspired generative models termed PFGM++ that unifies diffusion models and Poisson Flow Generative Models (PFGM). These models realize generative trajectories for N dimensional data by embedding paths in N{+}D dimensional space while still controlling the progression with a simple scalar norm of the D additional variables. The new models reduce to PFGM when D{=}1 and to diffusion models when D{to}infty. The flexibility of choosing D allows us to trade off robustness against rigidity as increasing D results in more concentrated coupling between the data and the additional variable norms. We dispense with the biased large batch field targets used in PFGM and instead provide an unbiased perturbation-based objective similar to diffusion models. To explore different choices of D, we provide a direct alignment method for transferring well-tuned hyperparameters from diffusion models (D{to} infty) to any finite D values. Our experiments show that models with finite D can be superior to previous state-of-the-art diffusion models on CIFAR-10/FFHQ 64{times}64 datasets, with FID scores of 1.91/2.43 when D{=}2048/128. In class-conditional setting, D{=}2048 yields current state-of-the-art FID of 1.74 on CIFAR-10. In addition, we demonstrate that models with smaller D exhibit improved robustness against modeling errors. Code is available at https://github.com/Newbeeer/pfgmpp

We utilize generalized moving least squares (GMLS) to develop meshfree techniques for discretizing hydrodynamic flow problems on manifolds. We use exterior calculus to formulate incompressible hydrodynamic equations in the Stokesian regime and handle the divergence-free constraints via a generalized vector potential. This provides less coordinate-centric descriptions and enables the development of efficient numerical methods and splitting schemes for the fourth-order governing equations in terms of a system of second-order elliptic operators. Using a Hodge decomposition, we develop methods for manifolds having spherical topology. We show the methods exhibit high-order convergence rates for solving hydrodynamic flows on curved surfaces. The methods also provide general high-order approximations for the metric, curvature, and other geometric quantities of the manifold and associated exterior calculus operators. The approaches also can be utilized to develop high-order solvers for other scalar-valued and vector-valued problems on manifolds.

Neural surrogates offer a promising route to accelerating computationally expensive simulations governed by partial differential equations across science and industry. Their practical deployment, however, is limited by unreliable predictions under out-of-distribution (OOD) conditions. We develop a solver-coupled surrogate-Newton framework that uses surrogate predictions as high-quality initial guesses for Newton-Krylov iterations, thereby combining rapid global flow-field prediction with high-accuracy numerical convergence at the terminal stage. On an OOD benchmark comprising geometries sampled from actual transonic airfoil optimization trajectories, the framework lowers the median residual L_2 ratio by over seven orders of magnitude while substantially reducing field and aerodynamic errors. In practical supercritical airfoil optimization, it improves online prediction reliability while achieving a 15.5-fold generation-level speedup over CFD. We further test the framework's extension to three dimensions using a flying-wing dataset. Together, these studies demonstrate the potential of surrogate-Newton coupling to deliver accurate, efficient and scalable steady CFD across industrial workflows.

Physical systems commonly exhibit spatially varying complexity, presenting a significant challenge for neural PDE solvers. While Graph Neural Networks can handle the irregular meshes required for complex geometries and boundary conditions, they still apply uniform computational effort across all nodes regardless of the underlying physics complexity. This leads to inefficient resource allocation where computationally simple regions receive the same treatment as complex phenomena. We address this challenge by introducing Adaptive Mesh Quantization: spatially adaptive quantization across mesh node, edge, and cluster features, dynamically adjusting the bit-width used by a quantized model. We propose an adaptive bit-width allocation strategy driven by a lightweight auxiliary model that identifies high-loss regions in the input mesh. This enables dynamic resource distribution in the main model, where regions of higher difficulty are allocated increased bit-width, optimizing computational resource utilization. We demonstrate our framework's effectiveness by integrating it with two state-of-the-art models, MP-PDE and GraphViT, to evaluate performance across multiple tasks: 2D Darcy flow, large-scale unsteady fluid dynamics in 2D, steady-state Navier-Stokes simulations in 3D, and a 2D hyper-elasticity problem. Our framework demonstrates consistent Pareto improvements over uniformly quantized baselines, yielding up to 50% improvements in performance at the same cost.

We present anyakrakusuma, an open-source Python library that solves the discrete static Schrödinger bridge problem, the entropically regularized counterpart of optimal transport, through a log-domain Sinkhorn--Knopp iteration and reconstructs the entropic interpolation between two empirical point clouds. The solver is paired with a diagnostic pipeline that characterizes the optimal coupling and the intermediate distributions through information-theoretic and geometric measures. We exercise the library on four idealized planar cases spanning a circle-to-circle dilation, a spiral-to-mixture fragmentation, a rigid reorientation of two moons, and a Lissajous-to-trefoil deformation. The log-domain formulation is necessary rather than merely convenient at the parameters studied, where the cost-to-regularization ratio reaches four hundred and the Gibbs kernel underflows double precision across most of its range; the iteration nonetheless attains a marginal residual of 10^{-9} and unit marginal fidelity in every case. Residual histories decay geometrically over approximately eight decades at per-iteration contraction factors between 0.966 and 0.976, which are local rates near the fixed point that lie many orders of magnitude below the worst-case Hilbert-metric bound. The covariance analysis recovers an imposed ninety-degree reorientation to within 0.07^circ, roughly forty times smaller than its uncertainty, across a masked interval of near-isotropy on which the principal axis is unobservable. The diagnostics are reported with explicit attention to the regimes in which each is well defined, including the differential entropy, which is meaningful only on the open interpolation interval. The presented cases are constructed rather than measured; quantitative application to empirical point clouds requires further study.

In aerodynamics, accurately modeling subsonic compressible flow over airfoils is critical for aircraft design. However, solving the governing nonlinear perturbation velocity potential equation presents computational challenges. Traditional approaches often rely on linearized equations or finite, truncated domains, which introduce non-negligible errors and limit applicability in real-world scenarios. In this study, we propose a novel framework utilizing Physics-Informed Neural Networks (PINNs) to solve the full nonlinear compressible potential equation in an unbounded (infinite) domain. We address the unbounded-domain and convergence challenges inherent in standard PINNs by incorporating a coordinate transformation and embedding physical asymptotic constraints directly into the network architecture. Furthermore, we employ a Multi-Stage PINN (MS-PINN) approach to iteratively minimize residuals, achieving solution accuracy approaching machine precision. We validate this framework by simulating flow over circular and elliptical geometries, comparing our results against traditional finite-domain and linearized solutions. Our findings quantify the noticeable discrepancies introduced by domain truncation and linearization, particularly at higher Mach numbers, and demonstrate that this new framework is a robust, high-fidelity tool for computational fluid dynamics.

Flow Matching (FM) constructs linear conditional probability paths, but the learned marginal velocity field inevitably exhibits strong curvature due to trajectory superposition. This curvature severely inflates numerical truncation errors, bottlenecking few-step sampling. To overcome this, we introduce Isokinetic Flow Matching (Iso-FM), a lightweight, Jacobian-free dynamical regularizer that directly penalizes pathwise acceleration. By using a self-guided finite-difference approximation of the material derivative Dv/Dt, Iso-FM enforces local velocity consistency without requiring auxiliary encoders or expensive second-order autodifferentiation. Operating as a pure plug-and-play addition to single-stage FM training, Iso-FM dramatically improves few-step generation. On CIFAR-10 (DiT-S/2), Iso-FM slashes conditional non-OT FID at 2 steps from 78.82 to 27.13 - a 2.9x relative efficiency gain - and reaches a best-observed FID at 4 steps of 10.23. These results firmly establish acceleration regularization as a principled, compute-efficient mechanism for fast generative sampling.

In the literature, flows produced by synthetic jets (SJ) have been studied extensively through experiments and numeric simulations. The essential physics of such a complex system has been simplified successfully to Lumped-element models in a wide range of conditions. LE models effectively predict the pressure in the cavity and the velocity in the neck of SJ. But, this does not comprise the complete dynamics of SJ. As soon as the flow starts separating from the neck of the SJ device, vortices and jets form at some distance downstream. These structures are the result of loosening the flow boundaries. Despite such a dramatic change, predictions of LE models remain unverified by measurements of the fully developed jet. We compared predictions of momentum transfer using an LE model with measurements of size and velocity of a fully developed jet/vortex detached from an SJ. Our SJ device operated with air as an active fluid. Comparing measurements and predictions, we found a constant difference for the higher sound pressures. However, the predictions and the measurements follow similar trends. Additionally, we found that the decay rate of the flow regime given by the relationship between the Reynolds and the Strouhal numbers differs significantly when the flow is studied within the neck and downstream the cavity.

Using absorbance measurements through a Couette cell containing an emulsion of buoyant droplets, volume fraction profiles are measured at various shear rates. These viscous resuspension experiments allow a direct determination of the normal stress in the vorticity direction in connection with the suspension balance model that has been developed for suspensions of solid particles. The results unambigously show that the normal viscosity responsible for the shear-induced migration of the droplets is independant on the capillary number, implying that particle deformation does not play a great role. It is similar to that of rigid particles at volume fractions below 40\% but much smaller at higher ones.

We show that Hertzian particle contacts are the underlying cause of the as-yet-unexplained noninteger power laws in weakly nonlinear rheology. In the medium amplitude oscillatory shear (MAOS) region, the cubic scaling of the leading order nonlinear shear stress (σ_3 sim γ_0^{m_3}, m_3=3) is the standard expectation. Expanding on the work by Natalia et al. [J. Rheol. 64 625-635 (2020)], we report an extensive data set of noncubical, noninteger power law scalings m_3 for particle suspensions in two immiscible fluids with a capillary attractive interaction, known as capillary suspensions. Here, we show that distinct power law exponents are found for the storage and loss moduli and these noninteger scalings occur at every secondary fluid concentration for two different contact angles. These compelling results indicate that the noninteger scalings are related to the underlying microstructure of capillary suspensions. We show that the magnitude of the third harmonic elastic stress scaling m_3,elastic originates from Hertzian-like contacts in combination with the attractive capillary force. The related third harmonic viscous stress scaling m_3,viscous is, found to be associated with adhesive-controlled friction. These observations, conducted for a wide range of compositions, can help explain previous reports of noninteger scaling for materials involving particle contacts and offers a new opportunity using the variable power law exponent of MAOS rheology to reveal the physics of particle bonds and friction in the rheological response under low deformation instead of at very high shear rates.

We demonstrate the feasibility of integrating physics-based animations of solids and fluids with 3D Gaussian Splatting (3DGS) to create novel effects in virtual scenes reconstructed using 3DGS. Leveraging the coherence of the Gaussian splatting and position-based dynamics (PBD) in the underlying representation, we manage rendering, view synthesis, and the dynamics of solids and fluids in a cohesive manner. Similar to Gaussian shader, we enhance each Gaussian kernel with an added normal, aligning the kernel's orientation with the surface normal to refine the PBD simulation. This approach effectively eliminates spiky noises that arise from rotational deformation in solids. It also allows us to integrate physically based rendering to augment the dynamic surface reflections on fluids. Consequently, our framework is capable of realistically reproducing surface highlights on dynamic fluids and facilitating interactions between scene objects and fluids from new views. For more information, please visit our project page at https://amysteriouscat.github.io/GaussianSplashing/.

Implicit Neural Spatial Representation (INSR) has emerged as an effective representation of spatially-dependent vector fields. This work explores solving time-dependent PDEs with INSR. Classical PDE solvers introduce both temporal and spatial discretizations. Common spatial discretizations include meshes and meshless point clouds, where each degree-of-freedom corresponds to a location in space. While these explicit spatial correspondences are intuitive to model and understand, these representations are not necessarily optimal for accuracy, memory usage, or adaptivity. Keeping the classical temporal discretization unchanged (e.g., explicit/implicit Euler), we explore INSR as an alternative spatial discretization, where spatial information is implicitly stored in the neural network weights. The network weights then evolve over time via time integration. Our approach does not require any training data generated by existing solvers because our approach is the solver itself. We validate our approach on various PDEs with examples involving large elastic deformations, turbulent fluids, and multi-scale phenomena. While slower to compute than traditional representations, our approach exhibits higher accuracy and lower memory consumption. Whereas classical solvers can dynamically adapt their spatial representation only by resorting to complex remeshing algorithms, our INSR approach is intrinsically adaptive. By tapping into the rich literature of classic time integrators, e.g., operator-splitting schemes, our method enables challenging simulations in contact mechanics and turbulent flows where previous neural-physics approaches struggle. Videos and codes are available on the project page: http://www.cs.columbia.edu/cg/INSR-PDE/

We present the Variational Incompressible Optimal Transport (VIOT) operator, a generative neural operator for amortized incompressible density transport. Given a new source-target density pair, VIOT predicts a divergence-free velocity field and generates the full transport trajectory by feed-forward inference, replacing the hour-scale per-pair optimization used by adjoint fluid solvers and differentiable simulation baselines. The system consists of three components: a stream-function or vector-potential representation that enforces incompressibility by construction, a regularized incompressible transport objective that balances endpoint accuracy and flow smoothness, and a Fourier Neural Operator backbone that amortizes the solve across new pairs and grid resolutions. Together, these components make incompressible transport a reusable neural operator that facilitates various transport processes. Further, the generative capability extends beyond the training distribution, with VIOT producing incompressible transports for user-drawn source-target pairs in a real-time interactive system. We demonstrate VIOT on 2D and 3D density-transport benchmarks. Both 2D and 3D rollouts complete in seconds per pair, while per-instance baselines in our 2D comparisons optimize each new pair from scratch and require on the order of an hour, a roughly 10^4times online speedup.

The ability to resolve complex physical phenomena with high fidelity and at low computational cost is central to addressing key challenges in modern engineering. A prime example lies in hypersonic flows, where the precise prediction of the full flowfield topology, in particular with respect to shock wave location and intensity, is critical. Yet supersonic and hypersonic flows continue to be a stumbling block for traditional reduced-order models and neural emulators that struggle to capture steep gradients in flow states with physical consistency in applications of industrial relevance. To that end, we introduce a fully GPU based workflow that integrates accelerated data generation with the training of neural emulators augmented by uncertainty quantification and physics-aware refinement. Our workflow is enabled by a differentiable high-fidelity solver (JAX-Fluids) which we employ for rapid dataset creation and residual-based improvement of the neural emulator to enhance physical consistency. Building on this framework, we first present a suite of model architectures and analyze their scaling behavior to expose their strengths and shortcomings. We then show that residual-based refinement enables training on cases where only mesh and input parameters are available, substantially reducing residuals and improving physical consistency. Together, differentiable simulation and residual-based refinement yield physics emulators that remain reliable beyond their training distribution, a key requirement for deploying surrogates in real-world engineering design loops.

We propose a hybrid neural network (NN) and PDE approach for learning generalizable PDE dynamics from motion observations. Many NN approaches learn an end-to-end model that implicitly models both the governing PDE and constitutive models (or material models). Without explicit PDE knowledge, these approaches cannot guarantee physical correctness and have limited generalizability. We argue that the governing PDEs are often well-known and should be explicitly enforced rather than learned. Instead, constitutive models are particularly suitable for learning due to their data-fitting nature. To this end, we introduce a new framework termed "Neural Constitutive Laws" (NCLaw), which utilizes a network architecture that strictly guarantees standard constitutive priors, including rotation equivariance and undeformed state equilibrium. We embed this network inside a differentiable simulation and train the model by minimizing a loss function based on the difference between the simulation and the motion observation. We validate NCLaw on various large-deformation dynamical systems, ranging from solids to fluids. After training on a single motion trajectory, our method generalizes to new geometries, initial/boundary conditions, temporal ranges, and even multi-physics systems. On these extremely out-of-distribution generalization tasks, NCLaw is orders-of-magnitude more accurate than previous NN approaches. Real-world experiments demonstrate our method's ability to learn constitutive laws from videos.

Scientific applications increasingly demand real-time surrogate models that can capture the behavior of strongly coupled multiphysics systems driven by multiple input functions, such as in thermo-mechanical and electro-thermal processes. While neural operator frameworks, such as Deep Operator Networks (DeepONets), have shown considerable success in single-physics settings, their extension to multiphysics problems remains poorly understood. In particular, the challenge of learning nonlinear interactions between tightly coupled physical fields has received little systematic attention. This study addresses a foundational question: should the architectural design of a neural operator reflect the strength of physical coupling it aims to model? To answer this, we present the first comprehensive, architecture-aware evaluation of DeepONet variants across three regimes: single-physics, weakly coupled, and strongly coupled multiphysics systems. We consider a reaction-diffusion equation with dual spatial inputs, a nonlinear thermo-electrical problem with bidirectional coupling through temperature-dependent conductivity, and a viscoplastic thermo-mechanical model of steel solidification governed by transient phase-driven interactions. Two operator-learning frameworks, the classical DeepONet and its sequential GRU-based extension, S-DeepONet, are benchmarked using both single-branch and multi-branch (MIONet-style) architectures. Our results demonstrate that architectural alignment with physical coupling is crucial: single-branch networks significantly outperform multi-branch counterparts in strongly coupled settings, whereas multi-branch encodings offer advantages for decoupled or single-physics problems. Once trained, these surrogates achieve full-field predictions up to 1.8e4 times faster than high-fidelity finite-element solvers, without compromising solution accuracy.

Recent advances in neural surrogate modeling offer the potential for transformative innovations in applications such as automotive aerodynamics. Yet, industrial-scale problems often involve volumetric meshes with cell counts reaching the 100 millions, presenting major scalability challenges. Complex geometries further complicate modeling through intricate surface-volume interactions, while quantities such as vorticity are highly nonlinear and must satisfy strict divergence-free constraints. To address these requirements, we introduce AB-UPT as a novel modeling scheme for building neural surrogates for CFD simulations. AB-UPT is designed to: (i) decouple geometry encoding and prediction tasks via multi-branch operators; (ii) enable scalability to high-resolution outputs via neural simulation in a low-dimensional latent space, coupled with anchored neural field decoders to predict high-fidelity outputs; (iii) enforce physics consistency by a novel divergence-free formulation. We show that AB-UPT yields state-of-the-art predictive accuracy of surface and volume fields on automotive CFD simulations ranging from 33 thousand up to 150 million mesh cells. Furthermore, our anchored neural field architecture enables the enforcement of hard physical constraints on the physics predictions without degradation in performance, exemplified by modeling divergence-free vorticity fields. Notably, the proposed models can be trained on a single GPU in less than a day and predict industry-standard surface and volume fields within seconds. Additionally, we show that the flexible design of our method enables neural simulation from a CAD geometry alone, omitting the need for costly CFD meshing procedures.

This study investigates the application of deep residual networks for predicting the dynamics of interacting three-dimensional rigid bodies. We present a framework combining a 3D physics simulator implemented in C++ with a deep learning model constructed using PyTorch. The simulator generates training data encompassing linear and angular motion, elastic collisions, fluid friction, gravitational effects, and damping. Our deep residual network, consisting of an input layer, multiple residual blocks, and an output layer, is designed to handle the complexities of 3D dynamics. We evaluate the network's performance using a datasetof 10,000 simulated scenarios, each involving 3-5 interacting rigid bodies. The model achieves a mean squared error of 0.015 for position predictions and 0.022 for orientation predictions, representing a 25% improvement over baseline methods. Our results demonstrate the network's ability to capture intricate physical interactions, with particular success in predicting elastic collisions and rotational dynamics. This work significantly contributes to physics-informed machine learning by showcasing the immense potential of deep residual networks in modeling complex 3D physical systems. We discuss our approach's limitations and propose future directions for improving generalization to more diverse object shapes and materials.

Polymer membranes are typically assumed to be inert and nonresponsive to the flux and density of the permeating particles in transport processes. Here, we study theoretically the consequences of membrane responsiveness and feedback on the steady-state force--flux relations and membrane permeability using a nonlinear-feedback solution-diffusion model of transport through a slab-like membrane. Therein, the solute concentration inside the membrane depends on the bulk concentration, c_0, the driving force, f, and the polymer volume fraction, phi. In our model, solute accumulation in the membrane causes a sigmoidal volume phase transition of the polymer, changing its permeability, which, in return, affects the membrane's solute uptake. This feedback leads to nonlinear force--flux relations, j(f), which we quantify in terms of the system's differential permeability, P_sys^{Delta}mathrm{dj}/{df}. We find that the membrane feedback can increase or decrease the solute flux by orders of magnitude, triggered by a small change in the driving force, and largely tunable by attractive versus repulsive solute--membrane interactions. Moreover, controlling the input, c_0 and f, can lead to steady-state bistability of phi and hysteresis in the force--flux relations. This work advocates that the fine-tuning of the membrane's chemo-responsiveness will enhance the nonlinear transport control features, providing great potential for future (self-)regulating membrane devices.

Modern techniques for physical simulations rely on numerical schemes and mesh-refinement methods to address trade-offs between precision and complexity, but these handcrafted solutions are tedious and require high computational power. Data-driven methods based on large-scale machine learning promise high adaptivity by integrating long-range dependencies more directly and efficiently. In this work, we focus on fluid dynamics and address the shortcomings of a large part of the literature, which are based on fixed support for computations and predictions in the form of regular or irregular grids. We propose a novel setup to perform predictions in a continuous spatial and temporal domain while being trained on sparse observations. We formulate the task as a double observation problem and propose a solution with two interlinked dynamical systems defined on, respectively, the sparse positions and the continuous domain, which allows to forecast and interpolate a solution from the initial condition. Our practical implementation involves recurrent GNNs and a spatio-temporal attention observer capable of interpolating the solution at arbitrary locations. Our model not only generalizes to new initial conditions (as standard auto-regressive models do) but also performs evaluation at arbitrary space and time locations. We evaluate on three standard datasets in fluid dynamics and compare to strong baselines, which are outperformed both in classical settings and in the extended new task requiring continuous predictions.

The dynamics of cells, organisms, and fluids are often modeled as probability distributions evolving over time. Reconstructing and extrapolating this evolution from unpaired snapshots requires assumptions about the underlying process. Wasserstein gradient flows are a common choice, but they cannot describe conservative or periodic dynamics. Lagrangian mechanics in Wasserstein space covers both, but existing methods for learning it are simulation-based: they run a numerical solver at every training step, which makes training expensive. We propose Double-Stitch, a simulation-free method that learns these mechanics by penalizing the residual of the equation of motion along a learned population path. We derive this equation from a Clebsch variational principle that does not require gradient velocities, and show that the residual vanishes exactly when the equation holds. We test Double-Stitch on synthetic, single-cell and ocean vortex datasets and find that it matches or outperforms gradient-flow methods and simulation-based WLM on most tasks, while training 4-14 times faster than WLM. We provide a JAX implementation of Double-Stitch at https://github.com/BasisResearch/stitching.

Physical principles are fundamental to realistic visual simulation, but remain a significant oversight in transformer-based video generation. This gap highlights a critical limitation in rendering rigid body motion, a core tenet of classical mechanics. While computer graphics and physics-based simulators can easily model such collisions using Newton formulas, modern pretrain-finetune paradigms discard the concept of object rigidity during pixel-level global denoising. Even perfectly correct mathematical constraints are treated as suboptimal solutions (i.e., conditions) during model optimization in post-training, fundamentally limiting the physical realism of generated videos. Motivated by these considerations, we introduce, for the first time, a physics-aware reinforcement learning paradigm for video generation models that enforces physical collision rules directly in high-dimensional spaces, ensuring the physics knowledge is strictly applied rather than treated as conditions. Subsequently, we extend this paradigm to a unified framework, termed Mimicry-Discovery Cycle (MDcycle), which allows substantial fine-tuning while fully preserving the model's ability to leverage physics-grounded feedback. To validate our approach, we construct new benchmark PhysRVGBench and perform extensive qualitative and quantitative experiments to thoroughly assess its effectiveness.

We verify a recent prediction (Eq. 3.50 in G. L. Eyink, Phys. Rev. X 11, 031054 (2021)) for the drag on an object moving through a fluid. In this prediction the velocity field is decomposed into a nonvortical (potential) and vortical contribution, and so is the associated drag force. In the Josephson-Anderson relation the vortical contribution of the drag force follows from the flux of vorticity traversing the streamlines of the corresponding potential flow. The potential component is directly determined by the plate acceleration and its added mass. The Josephson-Anderson relation is derived from the quantum description of superfluids, but remarkably applies to the classical fluid in our experiment. In our experiment a flat plate is accelerated through water using a robotic arm. This geometry is simple enough to allow analytic potential flow streamlines. The monitored plate position shows an oscillatory component of the acceleration, which adds an additional test of the Josephson-Anderson relation. The instantaneous velocity field is measured using particle image velocimetry. It enables us to evaluate Eq. 3.50 from [1] and compare its prediction to the measured drag force. We find excellent agreement, and, most remarkably find that the added mass contribution to the drag force still stands out after the flow has turned vortical. We finally comment on the requirements on the experimental techniques for evaluating the Josephson-Anderson relation.

We study the two-dimensional periodic resistive compressible magnetohydrodynamic equations with constant shear viscosity and magnetic diffusivity, bulk viscosity ρ^β, and pressure ρ^γ. For every β>1 and γ>1, we construct global finite-energy renormalized weak solutions from strictly positive bounded W^{1,q} densities, q>2, and arbitrary H^1 velocity and magnetic data. The construction combines approximation-independent finite density moments, generalized effective-flux identities, and a joint logarithmic renormalization of the density and its entropy defect. An augmented relative energy containing the β-power density potential yields weak--strong uniqueness against positive H^2 strong solutions for the same full pressure range. We also establish global strong existence for a large-background family when γ>max{5-2β,β+1}. Writing m=intρ_0, the density perturbation is bounded in the scaled norm m^{(γ-3)/2}|ρ_0-m|_{H^2}, while the fixed H^2 velocity and magnetic norms need not be small. For sufficiently large m, frequency-dependent acoustic dissipation, staged vorticity weights, and a separate initial-layer flux estimate close a simultaneous bootstrap. The admissible pressure exponents have infimum 7/3, with the endpoint excluded. For β>2 the relevant damping rate is the minimum of the viscous and pressure-relaxation rates; keeping both rates extends the argument without an upper restriction on β. The strong theorem has no upper restriction on γ under this scaled density hypothesis; for fixed additive density perturbations it applies in the stated lower range up to γ=3.

We establish the existence of compactly supported solutions of the inviscid incompressible 2D Boussinesq equation with C^{1,frac{4{3}}-1-varepsilon}cap L^{2} force that develop a singularity in finite time. Importantly, the force preserves this regularity at the blow-up time. Moreover, the forces in the vorticity and density equations have compact support. The mechanism behind the blow-up is an accumulated hysteresis effect on the vorticity caused by an infinite chain of "degenerate" pendula and flickering density.

Heterogeneous high--performance computing architectures expose numerical algorithms to perturbations arising from the non--associativity of floating--point arithmetic. In Large--Eddy Simulation (LES), similar numerical effects may become relevant when they affect the filter--width entering the subgrid scale (SGS) model. This work investigates this mechanism for the least--squares (LSQ) based filter--width formulation, focusing on how floating--point effects are generated, transmitted, and coupled with the resolved flow. We show that, for fixed resolved kinematics, the LSQ filter--width is logarithmically non-expansive but not strictly contractive with respect to perturbations of the mesh metrics. Consequently, small disturbances may be transmitted with little attenuation through strongly directional filter-width responses. To mitigate this sensitivity, we introduce a scalar max--min compression of the directional mesh scales together with a bounded modulation based on the resolved velocity gradient. The resulting formulation reroutes floating--point perturbations through the filter-width operator, improving robustness while preserving the flow--dependent character of the original LSQ construction. The framework is assessed on heterogeneous CPU and GPU architectures for flow past a circular cylinder at Re=3900 and the Taylor--Green vortex at Re=1600. In the former, nearly one--to--one transmission of relative metric disturbances can become relevant when the transmitted perturbations interact with shear-layer transition. By contrast, on orthogonal Taylor--Green vortex grids, the accumulation pathway is structurally absent and no comparable macroscopic response develops. These results suggest floating--point sensitivity matters for LES filter--width formulations in heterogeneous computing environments.

We propose Riemannian Flow Matching (RFM), a simple yet powerful framework for training continuous normalizing flows on manifolds. Existing methods for generative modeling on manifolds either require expensive simulation, are inherently unable to scale to high dimensions, or use approximations for limiting quantities that result in biased training objectives. Riemannian Flow Matching bypasses these limitations and offers several advantages over previous approaches: it is simulation-free on simple geometries, does not require divergence computation, and computes its target vector field in closed-form. The key ingredient behind RFM is the construction of a relatively simple premetric for defining target vector fields, which encompasses the existing Euclidean case. To extend to general geometries, we rely on the use of spectral decompositions to efficiently compute premetrics on the fly. Our method achieves state-of-the-art performance on many real-world non-Euclidean datasets, and we demonstrate tractable training on general geometries, including triangular meshes with highly non-trivial curvature and boundaries.

This paper investigates the stability of steady transonic shocks with constant states in rectangular nozzles under small three dimensional perturbations of the external force and the exit pressure. Mathematically, the problem can be formulated as a nonlinear free boundary problem for a hyperbolic-elliptic coupled PDE system. One of the key difficulties lies in the arbitrary location of the background shock, which may lead to multiple shock solutions for the same external force and exit pressure under perturbations, revealing the instability of the background shock. We reformulate the steady Euler equations in terms of deformation and vorticity to effectively decompose the hyperbolic and elliptic modes. Linearizing the reformulated system and the Rankine-Hugoniot conditions at background transonic shocks, we find that the class of nonzero horizontal external forces helps to uniquely determine the shock location, where the conservation of mass plays a critical role. A delicate iteration is developed to establish the existence and structural stability of transonic shock solutions. Our analysis shows that the stability mechanisms of steady transonic shocks in flat and divergent nozzles are quite different in many aspects.

Structural vibrations are a source of unwanted noise in engineering systems like cars, trains or airplanes. Minimizing these vibrations is crucial for improving passenger comfort. This work presents a novel design optimization approach based on guided flow matching for reducing vibrations by placing beadings (indentations) in plate-like structures. Our method integrates a generative flow matching model and a surrogate model trained to predict structural vibrations. During the generation process, the flow matching model pushes towards manufacturability while the surrogate model pushes to low-vibration solutions. The flow matching model and its training data implicitly define the design space, enabling a broader exploration of potential solutions as no optimization of manually-defined design parameters is required. We apply our method to a range of differentiable optimization objectives, including direct optimization of specific eigenfrequencies through careful construction of the objective function. Results demonstrate that our method generates diverse and manufacturable plate designs with reduced structural vibrations compared to designs from random search, a criterion-based design heuristic and genetic optimization. The code and data are available from https://github.com/ecker-lab/Optimizing_Vibrating_Plates.

A droplet impacting a deep fluid bath is as common as rain over the ocean. If the impact is sufficiently gentle, the mediating air layer remains intact, and the droplet may rebound completely from the interface. In this work, we experimentally investigate the role of translational bath motion on the bouncing to coalescence transition. Over a range of parameters, we find that the relative bath motion systematically decreases the normal Weber number required to transition from bouncing to merging. Direct numerical simulations demonstrate that the depression created during impact combined with the translational motion of the bath enhances the air layer drainage on the upstream side of the droplet, ultimately favoring coalescence. A simple geometric argument is presented that rationalizes the collapse of the experimental threshold data, extending what is known for the case of axisymmetric normal impacts to the more general 3D scenario of interest herein.

Data-driven modeling of fluid dynamics has advanced rapidly with neural PDE solvers, yet a fair and strong benchmark remains fragmented due to the absence of unified PDE datasets and standardized evaluation protocols. Although architectural innovations are abundant, fair assessment is further impeded by the lack of clear disentanglement between spatial, temporal and loss modules. In this paper, we introduce FD-Bench, the first fair, modular, comprehensive and reproducible benchmark for data-driven fluid simulation. FD-Bench systematically evaluates 85 baseline models across 10 representative flow scenarios under a unified experimental setup. It provides four key contributions: (1) a modular design enabling fair comparisons across spatial, temporal, and loss function modules; (2) the first systematic framework for direct comparison with traditional numerical solvers; (3) fine-grained generalization analysis across resolutions, initial conditions, and temporal windows; and (4) a user-friendly, extensible codebase to support future research. Through rigorous empirical studies, FD-Bench establishes the most comprehensive leaderboard to date, resolving long-standing issues in reproducibility and comparability, and laying a foundation for robust evaluation of future data-driven fluid models. The code is open-sourced at https://anonymous.4open.science/r/FD-Bench-15BC.

Most artificial life simulators either operate on abstract substrates disconnected from physical reality, or simulate physically grounded worlds that do not scale to the population sizes required for open-ended evolution. We present Microcosmos, a simulation engine in which artificial lifeforms are modeled as elastic filament chains inhabiting a two-dimensional viscous fluid world, designed from the ground up for modern GPU hardware and end-to-end differentiable simulation. We validate the engine through four experiments. Hand-designed locomotion strategies confirm that the fluid coupling respects known physical constraints. Gradient-based optimization of filament folding demonstrates both the full differentiability of the simulator and the expressivity of the filament encodings. Neuroevolution and quality-diversity search produce a wide range of swimming and chemotaxis behaviors automatically. Linear scaling with particle count confirms the engine supports large-scale simulation. Microcosmos is released as an open platform with the long-term goal of supporting large-scale open-ended evolutionary simulations, designed to be physically plausible and computationally scalable.

Robotic grasping and surface exploration benefit from simultaneous measurement of normal and tangential forces and from surface information obtained through contact. Here, we present a compact magnetociliary tactile sensor (MagCilia) that combines a flexible magnetic-cilia structure with a Hall sensor for 3D force sensing. Quasi-static finite element analysis is used to investigate structural deformation and magnetic responses under multidirectional loading. To reconstruct forces from the coupled magnetic channels, we propose causal history fusion regression (CHFR), which combines current magnetic-field measurements with their recent changes. Five-fold cross-validation grouped by calibration record yields root-mean-square errors of 0.40, 0.57, and 0.69 N for Fx, Fy, and Fz, respectively, with corresponding coefficients of determination of 0.93, 0.90, and 0.92. Robotic experiments demonstrate tangential-force-guided gripper adjustment and multi-axis load monitoring under external perturbations. Frequency-domain features of the reconstructed forces distinguish six surface categories with 99.39% accuracy in three-fold cross-validation grouped by acquisition session. An online robotic demonstration additionally identifies all six tested surfaces. These results demonstrate 3D force reconstruction, grasping feedback, and surface recognition using a single compact tactile unit.

Recent LLM-based agents have closed substantial portions of the scientific discovery loop in software-only machine-learning research, in chemistry, and in biology. Extending the same loop to high-fidelity physical simulators is harder, because solver completion does not imply physical validity and many failure modes appear only in field-level imagery rather than in solver logs. We present AI CFD Scientist, an open-source AI scientist for computational fluid dynamics (CFD) that, to our knowledge, is the first to span literature-grounded ideation, validated execution, vision-based physics verification, source-code modification, and figure-grounded writing within a single inspectable workflow. Three coupled pathways cover parameter sweeps within a fixed solver, case-local C++ library compilation for new physical models, and open-ended hypothesis search against a reference comparator, all running on OpenFOAM through Foam-Agent. At the center of the framework is a vision-language physics-verification gate that inspects rendered flow fields before any result is accepted, rerun, or written into a manuscript. On five tasks under a shared GPT-5.5 backbone, AI CFD Scientist autonomously discovers a Spalart-Allmaras runtime correction that reduces lower-wall Cf RMSE against DNS by 7.89% on the periodic hill at Reh=5600; under matched LLM cost, two strong general AI-scientist baselines (ARIS, DeepScientist) execute partial CFD workflows but lack the domain-specific validity gates needed to convert runs into defensible scientific claims; and a controlled planted-failure ablation shows that the vision-language gate detects 14 of 16 silent failures missed by solver-level checks. Code, prompts, and run artifacts are released at https://github.com/csml-rpi/cfd-scientist.

Recent flow cessation experiments on soft materials have shown a counter-intuitive non-monotonic relaxation of the shear stress: following the switch-off of a steady imposed shear flow, the stress initially decays before later increasing again. By simulating the soft glassy rheology model in a form extended to allow steady state shear banding, we show that the presence of shear bands prior to flow cessation can give rise to this phenomenon. We give a mechanistic understanding of the basic physics involved, in terms of (i) the decay of the shear bands after flow cessation, and (ii) the evolution of frustrated local stresses, governed by different time scales for plastic relaxation in each band. In particular, an elastic recoil in the unsheared band gives rise to negative local frustrated stresses, the slow release of which can cause an increase in macroscopic stress. Given that shear banding and frustrated local stresses arise widely across disordered soft solids, we argue that non-monotonic stress relaxation after flow cessation may occur in many different materials.

Physics-Informed machine learning models have recently emerged with some interesting and unique features that can be applied to reservoir engineering. In particular, physics-informed neural networks (PINN) leverage the fact that neural networks are a type of universal function approximators that can embed the knowledge of any physical laws that govern a given data-set in the learning process, and can be described by partial differential equations. The transient diffusivity equation is a fundamental equation in reservoir engineering and the general solution to this equation forms the basis for Pressure Transient Analysis (PTA). The diffusivity equation is derived by combining three physical principles, the continuity equation, Darcy's equation, and the equation of state for a slightly compressible liquid. Obtaining general solutions to this equation is imperative to understand flow regimes in porous media. Analytical solutions of the transient diffusivity equation are usually hard to obtain due to the stiff nature of the equation caused by the steep gradients of the pressure near the well. In this work we apply physics-informed neural networks to the one and two dimensional diffusivity equation and demonstrate that decomposing the space domain into very few subdomains can overcome the stiffness problem of the equation. Additionally, we demonstrate that the inverse capabilities of PINNs can estimate missing physics such as permeability and distance from sealing boundary similar to buildup tests without shutting in the well.

Accurately predicting the future fluid is important to extensive areas, such as meteorology, oceanology and aerodynamics. However, since the fluid is usually observed from an Eulerian perspective, its active and intricate dynamics are seriously obscured and confounded in static grids, bringing horny challenges to the prediction. This paper introduces a new Lagrangian-guided paradigm to tackle the tanglesome fluid dynamics. Instead of solely predicting the future based on Eulerian observations, we propose the Eulerian-Lagrangian Dual Recurrent Network (EuLagNet), which captures multiscale fluid dynamics by tracking movements of adaptively sampled key particles on multiple scales and integrating dynamics information over time. Concretely, a EuLag Block is presented to communicate the learned Eulerian and Lagrangian features at each moment and scale, where the motion of tracked particles is inferred from Eulerian observations and their accumulated dynamics information is incorporated into Eulerian fields to guide future prediction. Tracking key particles not only provides a clear and interpretable clue for fluid dynamics but also makes our model free from modeling complex correlations among massive grids for better efficiency. Experimentally, EuLagNet excels in three challenging fluid prediction tasks, covering both 2D and 3D, simulated and real-world fluids.

In detuned optical cavities, the radiation pressure force acting on the mirrors depends on their displacements. This is equivalent to the rigidity (the optical spring), inserted between the mirrors. This effect can be used for optimization of the mechanical susceptibility of probe mirrors in high-precision force sensors. However, in some cases, the use of detuned cavities or even just any high-finesse cavities could be problematic due to technological constraints. We consider a new type of the optical spring that does not require the cavity (but can use a resonance tuned one to increase the optomechanical coupling). Instead, it uses the double interaction of the probing light with the mechanical object. We propose two possible implementation of this concept, suitable, respectively, for the atomic spin ensembles and for the laser gravitational-wave detectors.

We establish nonlinear stability of three-dimensional Couette flow for the incompressible Navier--Stokes equations on mathbb Ttimesmathbb R^2. Divergence-free perturbations satisfying |u_{rm in}|_{H^2}+|u^perp_{0,rm in}|_{dot B^{-2}_{2,infty}}leq c_*ν generate unique global H^2 solutions that remain close to Couette flow, where u^perp_{0,rm in} denotes the streamwise average of the transverse velocity. This result retains the O(ν) stability threshold despite the absence of a spanwise spectral gap. The nonzero streamwise modes exhibit enhanced dissipation, their wall-normal component satisfies a viscosity-uniform time-integrated inviscid-damping estimate, and the transverse zero mode decays in L^2 at rate (1+νt)^{-1}. The endpoint space dot B^{-2}_{2,infty} controls the transverse low frequencies, accommodates divergence-form nonlinear forcing, and is critical for linear lift-up from the wall-normal zero mode. The proof combines propagation of this endpoint norm, Fourier splitting, and a two-level roll-to-streak representation with an adaptation of the nonzero-mode framework of Wei--Zhang (CPAM, 2021).

We present a computational framework that transforms single images into 3D physical objects. The visual geometry of a physical object in an image is determined by three orthogonal attributes: mechanical properties, external forces, and rest-shape geometry. Existing single-view 3D reconstruction methods often overlook this underlying composition, presuming rigidity or neglecting external forces. Consequently, the reconstructed objects fail to withstand real-world physical forces, resulting in instability or undesirable deformation -- diverging from their intended designs as depicted in the image. Our optimization framework addresses this by embedding physical compatibility into the reconstruction process. We explicitly decompose the three physical attributes and link them through static equilibrium, which serves as a hard constraint, ensuring that the optimized physical shapes exhibit desired physical behaviors. Evaluations on a dataset collected from Objaverse demonstrate that our framework consistently enhances the physical realism of 3D models over existing methods. The utility of our framework extends to practical applications in dynamic simulations and 3D printing, where adherence to physical compatibility is paramount.

Accurate prediction of Lagrangian trajectories in turbulent flow remains challenging due to limited temporal information in transport functions. This paper shows that surrounding coherent motions sharing the same dynamics carry enough information to provide highly probable trajectories even from sparse temporal observations. The proposed coherent predictor builds on Lagrangian coherent structures (LCSs), the advective transport barriers that govern the cohesive motion of neighbouring particles. Coherent trajectories are quantified using a local segmentation with the finite-time Lyapunov exponents (FTLE). The coherent predictor incorporates information from the particle's position history and neighbouring coherent velocity and acceleration into a novel cost function to predict its trajectory. The proposed cost function follows a physics-informed approach where the position history acts as a data fidelity term and the coherent velocity and acceleration act as physics-based regularisation constraints. We assess our proposed approach using both three-dimensional (3D) synthetic and experimental data of the wake behind a smooth cylinder and two-dimensional (2D) homogeneous isotropic turbulent (HIT) flow. The coherent predictor is deemed generic due to its consistent behaviour regardless of flow dimensions, Reynolds number, and flow topology. Our results show that the optimal cost function parameters can be modelled from the measurement uncertainties, giving lower prediction error and uncertainty than current methods. We see direct signatures of flow topology on the prediction error map, including the cylinder leading edge boundary layer, the sideward shear layers, and the vortex formation structures. These topologies are marked by high Lagrangian gradients and 3D directional motions.

Imposing known physical constraints, such as conservation laws, during neural network training introduces an inductive bias that can improve accuracy, reliability, convergence, and data efficiency for modeling physical dynamics. While such constraints can be softly imposed via loss function penalties, recent advancements in differentiable physics and optimization improve performance by incorporating PDE-constrained optimization as individual layers in neural networks. This enables a stricter adherence to physical constraints. However, imposing hard constraints significantly increases computational and memory costs, especially for complex dynamical systems. This is because it requires solving an optimization problem over a large number of points in a mesh, representing spatial and temporal discretizations, which greatly increases the complexity of the constraint. To address this challenge, we develop a scalable approach to enforce hard physical constraints using Mixture-of-Experts (MoE), which can be used with any neural network architecture. Our approach imposes the constraint over smaller decomposed domains, each of which is solved by an "expert" through differentiable optimization. During training, each expert independently performs a localized backpropagation step by leveraging the implicit function theorem; the independence of each expert allows for parallelization across multiple GPUs. Compared to standard differentiable optimization, our scalable approach achieves greater accuracy in the neural PDE solver setting for predicting the dynamics of challenging non-linear systems. We also improve training stability and require significantly less computation time during both training and inference stages.

Humans possess an exceptional ability to imagine 4D scenes, encompassing both motion and 3D geometry, from a single still image. This ability is rooted in our accumulated observations of similar scenes and an intuitive understanding of physics. In this paper, we aim to replicate this capacity in neural networks, specifically focusing on natural fluid imagery. Existing methods for this task typically employ simplistic 2D motion estimators to animate the image, leading to motion predictions that often defy physical principles, resulting in unrealistic animations. Our approach introduces a novel method for generating 4D scenes with physics-consistent animation from a single image. We propose the use of a physics-informed neural network that predicts motion for each surface point, guided by a loss term derived from fundamental physical principles, including the Navier-Stokes equations. To capture appearance, we predict feature-based 3D Gaussians from the input image and its estimated depth, which are then animated using the predicted motions and rendered from any desired camera perspective. Experimental results highlight the effectiveness of our method in producing physically plausible animations, showcasing significant performance improvements over existing methods. Our project page is https://physfluid.github.io/ .

Neural surrogates and operator networks for solving partial differential equation (PDE) problems have attracted significant research interest in recent years. However, most existing approaches are limited in their ability to generalize solutions across varying non-parametric geometric domains. In this work, we address this challenge in the context of Polyethylene Terephthalate (PET) bottle buckling analysis, a representative packaging design problem conventionally solved using computationally expensive finite element analysis (FEA). We introduce a hybrid DeepONet-Transolver framework that simultaneously predicts nodal displacement fields and the time evolution of reaction forces during top load compression. Our methodology is evaluated on two families of bottle geometries parameterized by two and four design variables. Training data is generated using nonlinear FEA simulations in Abaqus for 254 unique designs per family. The proposed framework achieves mean relative L^{2} errors of 2.5-13% for displacement fields and approximately 2.4% for time-dependent reaction forces for the four-parameter bottle family. Point-wise error analyses further show absolute displacement errors on the order of 10^{-4}-10^{-3}, with the largest discrepancies confined to localized geometric regions. Importantly, the model accurately captures key physical phenomena, such as buckling behavior, across diverse bottle geometries. These results highlight the potential of our framework as a scalable and computationally efficient surrogate, particularly for multi-task predictions in computational mechanics and applications requiring rapid design evaluation.

Part-aware 3D asset generation enables applications such as editing, articulation, simulation, and fabrication, yet existing methods can generate visually complete individual parts without ensuring that they form a valid physical assembly. Consequently, generated neighboring parts may interpenetrate, lack valid connections, or collapse under gravity. We propose a physics-guided framework for improving single-image part-aware 3D generation with physically compatible geometry and stable connections. Our method resolves inter-part penetration, recovers a contact graph between neighboring parts, and introduces parameterized connectors at their contact surfaces. Using feedback from physical simulation, we refine connector placement, orientation, and dimensions to improve assembly stability while preserving the generated geometry. We further introduce a physics-based evaluation protocol that complements conventional geometric metrics by directly testing assembly validity and stability under gravity. Experiments comparing against multiple part-aware 3D generators show substantial improvements in physical realizability and stability while maintaining geometric quality. We additionally validate the resulting parts through 3D printing and real-world assembly.

Tobasco et al. [Physics Letters A, 382:382-386, 2018; see https://doi.org/10.1016/j.physleta.2017.12.023] recently suggested that trajectories of ODE systems that optimize the infinite-time average of a certain observable can be localized using sublevel sets of a function that arise when bounding such averages using so-called auxiliary functions. In this paper we demonstrate that this idea is viable and allows for the computation of extremal unstable periodic orbits (UPOs) for polynomial ODE systems. First, we prove that polynomial optimization is guaranteed to produce auxiliary functions that yield near-sharp bounds on time averages, which is required in order to localize the extremal orbit accurately. Second, we show that points inside the relevant sublevel sets can be computed efficiently through direct nonlinear optimization. Such points provide good initial conditions for UPO computations. As a proof of concept, we then combine these methods with a single-shooting Newton-Raphson algorithm to study extremal UPOs for a nine-dimensional model of sinusoidally forced shear flow. We discover three previously unknown families of UPOs, one of which simultaneously minimizes the mean energy dissipation rate and maximizes the mean perturbation energy relative to the laminar state for Reynolds numbers approximately between 81.24 and 125.

Operating robots precisely and at high speeds has been a long-standing goal of robotics research. Balancing these competing demands is key to enabling the seamless collaboration of robots and humans and increasing task performance. However, traditional motor-driven systems often fall short in this balancing act. Due to their rigid and often heavy design exacerbated by positioning the motors into the joints, faster motions of such robots transfer high forces at impact. To enable precise and safe dynamic motions, we introduce a four degree-of-freedom~(DoF) tendon-driven robot arm. Tendons allow placing the actuation at the base to reduce the robot's inertia, which we show significantly reduces peak collision forces compared to conventional robots with motors placed near the joints. Pairing our robot with pneumatic muscles allows generating high forces and highly accelerated motions, while benefiting from impact resilience through passive compliance. Since tendons are subject to additional friction and hence prone to wear and tear, we validate the reliability of our robotic arm on various experiments, including long-term dynamic motions. We also demonstrate its ease of control by quantifying the nonlinearities of the system and the performance on a challenging dynamic table tennis task learned from scratch using reinforcement learning. We open-source the entire hardware design, which can be largely 3D printed, the control software, and a proprioceptive dataset of 25 days of diverse robot motions at webdav.tuebingen.mpg.de/pamy2.

The active Brownian particle (ABP) model is one of the most widely used particle-based models in studies of scalar active fluids. A collection of interacting ABPs is known to exhibit intriguing phenomena that are absent in equilibrium counterparts. A prominent example is spontaneous phase separation, known as motility-induced phase separation (MIPS), which occurs even in the absence of explicit attractive interactions. In parallel, the large-scale behavior of scalar active fluids is often modeled using continuum descriptions, namely, scalar field theories. Such scalar active field theories are usually formulated in a top-down manner, and establishing their connections to particle-based models remains challenging, with these connections not yet fully understood. To advance the microscopic derivation of scalar active field theories, we revisit the connection between ABPs interacting via a two-body potential in two dimensions and scalar field theories that include all possible terms up to fourth order in spatial gradients. Our approach is based on a pressure expansion and the renormalization group (RG) method in the context of singular perturbation theory. The RG method provides a systematic way to eliminate fast variables and identify the dynamics on the slow invariant manifold. Within this framework, scalar field theories can be obtained as RG flow equations. We also apply this method to a chiral variant of the ABP model, the chiral ABP (cABP) model, in which a constant torque biases particle rotation to the left or right. We show that the scalar field theory corresponding to the cABP model contains two ``odd'' terms in addition to those present in the scalar field theory for ABPs. The method developed here may also be useful for deriving hydrodynamic descriptions of other types of active matter systems.

The transition of an impulsively excited kink oscillation of a solar coronal loop to an oscillation with a stationary amplitude, i.e., the damping pattern, is determined using the low-dimensional self-oscillation model. In the model, the decayless kink oscillations are sustained by the interaction of the oscillating loop with an external quasi-steady flow. The analytical solution is based on the assumption that the combined effect of the effective dissipation, for example, by resonant absorption, and interaction with an external flow, is weak. The effect is characterised by a dimensionless coupling parameter. The damping pattern is found to depend upon the initial amplitude and the coupling parameter. The approximate expression shows a good agreement with a numerical solution of the self-oscillation equation. The plausibility of the established damping pattern is demonstrated by an observational example. Notably, the damping pattern is not exponential, and the characteristic decay time is different from the time determined by the traditionally used exponential damping fit. Implications of this finding for seismology of the solar coronal plasmas are discussed. In particular, it is suggested that a very rapid, in less than the oscillation period, decay of the oscillation to the stationary level, achieved for larger values of the coupling parameter, can explain the relative rareness of the kink oscillation events.

Many soft-body organisms found in nature flourish underwater. Similarly, soft robots are potentially well-suited for underwater environments partly because the problematic effects of gravity, friction, and harmonic oscillations are less severe underwater. However, it remains a challenge to design, fabricate, waterproof, model, and control underwater soft robotic systems. Furthermore, submersible robots usually do not have configurable components because of the need for sealed electronics and mechanical elements. This work presents the development of a modular and submersible soft robotic arm driven by hydraulic actuators which consists of mostly 3D printable parts which can be assembled or modified in a relatively short amount of time. Its modular design enables multiple shape configurations and easy swapping of soft actuators. As a first step to exploring machine learning control algorithms on this system, we also present preliminary forward and inverse kinematics models developed using deep neural networks.

We present a boundary integral equation (BIE) framework for two-dimensional time-harmonic elastic transmission problems. Using the Helmholtz decomposition, the elastodynamic displacement fields are expressed in terms of scalar pressure and shear potentials, so that only the four classical Helmholtz boundary integral operators are needed. The key step is a rewriting of the Navier traction operator in the local normal--tangential frame of the interface, in which second-order normal derivatives are eliminated in favour of tangential derivatives and curvature terms. This leads to a one-parameter family of indirect combined field integral equations, depending on a coupling constant αne 0, which we prove to be uniquely solvable. The principal part of the resulting operator is, however, defective, and the discretized systems are severely ill-conditioned. Using the pseudodifferential calculus of the Helmholtz BIOs, we construct explicit left and right analytical preconditioners and prove that the preconditioned operator is a compact perturbation of the identity. Numerical experiments based on high-order Nyström discretizations confirm that the preconditioner clusters the spectrum: the number of GMRES iterations becomes independent of the discretization and is reduced by one order of magnitude or more, also in the high-frequency regime and for non-convex scatterers.

Representing 3D surfaces as level sets of continuous functions over R^3 is the common denominator of neural implicit representations, which recently enabled remarkable progress in geometric deep learning and computer vision tasks. In order to represent 3D motion within this framework, it is often assumed (either explicitly or implicitly) that the transformations which a surface may undergo are homeomorphic: this is not necessarily true, for instance, in the case of fluid dynamics. In order to represent more general classes of deformations, we propose to apply this theoretical framework as regularizers for the optimization of simple 4D implicit functions (such as signed distance fields). We show that our representation is capable of capturing both homeomorphic and topology-changing deformations, while also defining correspondences over the continuously-reconstructed surfaces.

Neural simulators promise efficient surrogates for physics simulation, but scaling them is bottlenecked by the prohibitive cost of generating high-fidelity training data. Pre-training on abundant off-the-shelf geometries offers a natural alternative, yet faces a fundamental gap: supervision on static geometry alone ignores dynamics and can lead to negative transfer on physics tasks. We present GeoPT, a unified pre-trained model for general physics simulation based on lifted geometric pre-training. The core idea is to augment geometry with synthetic dynamics, enabling dynamics-aware self-supervision without physics labels. Pre-trained on over one million samples, GeoPT consistently improves industrial-fidelity benchmarks spanning fluid mechanics for cars, aircraft, and ships, and solid mechanics in crash simulation, reducing labeled data requirements by 20-60% and accelerating convergence by 2times. These results show that lifting with synthetic dynamics bridges the geometry-physics gap, unlocking a scalable path for neural simulation and potentially beyond. Code is available at https://github.com/Physics-Scaling/GeoPT.

Numerical simulations in industrial applications often require performing numerous high-precision computations parameterized by specific experimental conditions. For instance, in vehicle body design, aerodynamic simulations are essential for evaluating the aerodynamic characteristics of various proposed body geometries. However, computational resource constraints often become a bottleneck. Therefore, achieving the desired accuracy while minimizing computational cost is crucial. To address this challenge, model reduction methods have been developed to decrease the degrees of freedom by constraining the possible states of a physical system to a lower-dimensional subspace. In particular, reduction techniques that project the system onto a nonlinear subspace using neural networks have been actively studied. Our previous research developed a reduced-order model that integrates neural-network-based model reduction with a time-evolution method, implemented as a distributed parallel training framework to process high-resolution flow field data efficiently. In this study, we extend this reduction approach by incorporating a variational autoencoder to assess its robustness in high-Reynolds-number flows around multiple vehicle bodies with varying geometries. Specifically, we evaluate the reconstruction accuracy of vortex generation across different spatial and temporal scales using a compact latent representation, with a particular focus on the flow behavior near the rear end of the vehicle body.

Entropically driven fluid-solid transitions in monodisperse, purely repulsive hard spheres (MPRHS) are well established in theory, simulation, and experiment for atomic and colloidal systems. For MPRHS, however, coexistence is usually located via bulk free-energy calculations; the underlying microscopic balance between configurational and vibrational entropy is left implicit. Frenkel clarified this mechanism explicitly as an exchange of long-range configurational entropy for short-range vibrational entropy, but in the pristine MPRHS limit the nucleation barrier near coexistence is so high that phase separation is predicted only on astronomical time scales. Consistent with this, even unbiased simulations do not show spontaneous, equilibrium fluid-crystal coexistence; transient mixtures are mostly overtaken by a single phase; observed coexistence is still algorithmically-driven. Nearly hard-sphere colloid experiments do observe fluid-crystal coexistence, but always in the presence of unavoidable triggers such as gravity, walls, and polydispersity. We treat the hard-sphere phase diagram as settled and ask how the entropic exchange mechanism can be revealed in nearly hard-sphere colloidal simulations. We probe the mechanism on finite time scales by introducing minimal perturbations that trigger phase separation: small reductions in hardness that increase locally accessible free volume (and thus gently increase vibrational entropy), and 2-4% distributed crystal seeds. These perturbations produce coexisting fluid and crystal domains with crystal fraction, phase envelope and osmotic pressure that, with systematically increasing particle hardness, approach the hard-sphere limit. These results demonstrate that slight enhancements to vibrational entropy provide a dynamically accessible route to realizing the long-range/short-range entropy exchange required for phase separation.

We prove strong ill-posedness for the two-dimensional incompressible Euler equation in the endpoint velocity space W^{3,1}_σ(mathbb R^2). Given any compactly supported smooth divergence-free background and any δ>0, we construct a single compactly supported divergence-free datum within δ of the background in W^{3,1}. The perturbation can be localized inside any prescribed nonempty open neighborhood of the background support while remaining disjoint from that support. The associated unique global finite-energy solution u satisfies {rm curl} uin C([0,infty);W^{2,1}(mathbb R^2)), but \[ \operatorname*{ess\,sup}_{0<t<T}\|u(t)\|_{W^{3,1}}=\infty \qquadfor every T>0. \] The proof combines localized hyperbolic insertion, the Bonami--Poornima nonmultiplier mechanism, and many-packet dilution. Moment cancellation and positive material separation control the nonlocal Biot--Savart interactions, allowing a nested construction inside one fixed compact region. Without the compact-support requirement on the limiting datum, a complementary far-field argument yields a dense G_δ set of data whose solutions leave W^{3,1} at every positive rational time and on a residual set of times, with unbounded essential supremum on every nonempty open time interval.

Recent advances in generative models highlight the power of geometry-aware modeling in manifold-constrained settings. Yet, for natural images, the field remains confined to Euclidean assumptions, failing to exploit the potential of intrinsic geometric structures within the data. In this work, we investigate the geometry of natural images and observe that semantic information is predominantly encoded in directional components, while norm components can be approximated by the global average. This property holds across both RGB and latent spaces, suggesting that natural images can be effectively modeled on a hypersphere. Building on this finding, we introduce Spherical Optimal Transport Flow Matching (SOT-CFM), which utilizes angular distance, and Spherical Flow Matching (SFM), which constrains dynamics directly on the manifold. Our experiments demonstrate that these geometry-aware methods achieve superior performance against Euclidean baselines. Ultimately, this work provides a novel perspective that bridges the gap between Riemannian manifold-based modeling and natural image generation.

Here we present a machine learning framework and model implementation that can learn to simulate a wide variety of challenging physical domains, involving fluids, rigid solids, and deformable materials interacting with one another. Our framework---which we term "Graph Network-based Simulators" (GNS)---represents the state of a physical system with particles, expressed as nodes in a graph, and computes dynamics via learned message-passing. Our results show that our model can generalize from single-timestep predictions with thousands of particles during training, to different initial conditions, thousands of timesteps, and at least an order of magnitude more particles at test time. Our model was robust to hyperparameter choices across various evaluation metrics: the main determinants of long-term performance were the number of message-passing steps, and mitigating the accumulation of error by corrupting the training data with noise. Our GNS framework advances the state-of-the-art in learned physical simulation, and holds promise for solving a wide range of complex forward and inverse problems.

The relationship between balance laws and the Principle of Virtual Work as well as the structure of contact interactions in continua remain foundational issues in Mechanics. In this work, we revisit these issues within the distributional framework emphasized by Paul Germain. We show that while the Principle of Virtual Work implies balance of forces and moments for nth-gradient continua, balance laws alone do not suffice to characterize equilibrium for n geq 2. We then reexamine Noll's classical theorem asserting that surface contact forces depend solely on the unit normal to the surface and identify the precise role of his additional assumptions, namely the absence of edge and wedge contact interactions and the boundedness of the surface contact density on the space of oriented surfaces. We demonstrate that these hypotheses fail for general higher-gradient continua. Consequently, the presence of curvature-dependent surface contact forces in such materials does not conflict with Noll's theorem and refutes his claim of their nonexistence.

Learning physical simulations has been an essential and central aspect of many recent research efforts in machine learning, particularly for Navier-Stokes-based fluid mechanics. Classic numerical solvers have traditionally been computationally expensive and challenging to use in inverse problems, whereas Neural solvers aim to address both concerns through machine learning. We propose a general formulation for continuous convolutions using separable basis functions as a superset of existing methods and evaluate a large set of basis functions in the context of (a) a compressible 1D SPH simulation, (b) a weakly compressible 2D SPH simulation, and (c) an incompressible 2D SPH Simulation. We demonstrate that even and odd symmetries included in the basis functions are key aspects of stability and accuracy. Our broad evaluation shows that Fourier-based continuous convolutions outperform all other architectures regarding accuracy and generalization. Finally, using these Fourier-based networks, we show that prior inductive biases, such as window functions, are no longer necessary. An implementation of our approach, as well as complete datasets and solver implementations, is available at https://github.com/tum-pbs/SFBC.

This paper constitutes Part III of a series investigating the excitation of non-modal perturbations in hypersonic blunt-nose boundary layers. Based on the numerical shock-fitting harmonic linearised Navier-Stokes (SF-HLNS) approach presented in Part I (Zhao & Dong, J. Fluid Mech. 2025, vol. 1013: A44) and the asymptotic analysis developed in Part II (Dong et al., J. Fluid Mech., under review), the present work focuses specifically on the influence of nose bluntness (Reynolds number R) and wall temperature T_w on receptivity efficiency through seven detailed case studies. Analysed via the three-step asymptotic model, the downstream perturbation amplitude is governed by two distinct factors: the stagnation vorticity perturbation, determined through shock-perturbation interaction and the slow-down convection mechanism, and the parabolic evolution of non-modal perturbations driven by the lift-up mechanism. Increasing R strongly amplifies the stagnation vorticity response, with only mild enhancement of the lift-up effect. In contrast, decreasing T_w strengthens the stagnation vorticity perturbation, but slightly weakens the lift-up effect; the net result is an overall intensification of the downstream perturbation amplitude with decreasing T_w. Furthermore, explicit scaling laws for receptivity efficiency with respect to R and T_w are established. This study completes the theoretical foundation for non-modal receptivity in hypersonic blunt boundary layers, and serves as a key step toward a physics-based transition prediction framework.

Normalizing flows (NF) are a class of powerful generative models that have gained popularity in recent years due to their ability to model complex distributions with high flexibility and expressiveness. In this work, we introduce a new type of normalizing flow that is tailored for modeling positions and orientations of multiple objects in three-dimensional space, such as molecules in a crystal. Our approach is based on two key ideas: first, we define smooth and expressive flows on the group of unit quaternions, which allows us to capture the continuous rotational motion of rigid bodies; second, we use the double cover property of unit quaternions to define a proper density on the rotation group. This ensures that our model can be trained using standard likelihood-based methods or variational inference with respect to a thermodynamic target density. We evaluate the method by training Boltzmann generators for two molecular examples, namely the multi-modal density of a tetrahedral system in an external field and the ice XI phase in the TIP4P water model. Our flows can be combined with flows operating on the internal degrees of freedom of molecules and constitute an important step towards the modeling of distributions of many interacting molecules.