hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.3.2.1 Definition | Conducted spurious emissions are any emissions from the antenna connector, when the MS is in idle mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.3.2.2 Conformance requirement | 1. The conducted spurious power emitted by the MS, when in idle mode, shall be no more than the levels in table 12.14.
1.1 Under normal voltage conditions; 3GPP TS 05.05, subclauses 4.3 and 4.3.3.
1.2 Under extreme voltage conditions; 3GPP TS 05.05, subclauses 4.3 and 4.3.3, and clause D.2.
Table 12.14
Frequency range
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.3.2.3 Test purpose | 1. To verify that conducted spurious emissions, in the frequency band 100 kHz to 12,75 GHz from the MS when in idle mode do not exceed the conformance requirements.
1.1 Under normal voltage conditions.
1.2 Under extreme voltage conditions.
NOTE: The band 9 kHz to 100 kHz is not tested, because of test implementation pr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.3.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.3.2.4.1 Initial conditions | The BCCH message content from the serving cell shall ensure that Periodic Location Updating is not used and that page mode is continuously set to Paging Reorganization and BS_AG_BLKS_RES is set to 0 so that the MS receiver will operate continually.
The CCCH_CONF shall be set to 000. 1 basic physical channel used for CC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.3.2.4.2 Procedure | a) Measurements are made in the frequency range 100 kHz to 12,75 GHz. Spurious emissions are measured as the power level of any discrete signal, higher than the requirement in table 12.14 minus 6 dB, delivered into a 50 load.
The measurement bandwidth based on a 5 pole synchronously tuned filter is set according to t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.3.2.5 Test requirement | The power of any spurious emission shall not exceed the levels given in table 12.16.
Table 12.16
Frequency range
Power level in dBm
Note
100 kHz to
880 MHz
-57
Common Requirement
876 MHz to
915 MHz
-59
For R-GSM
873 MHz to
915 MHz
-59
For ER-GSM
915 MHz to
1 000 MHz
-57
Common Requirement
1 GHz to
1 710 MHz
-47
Common ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4 Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band | This subclause applies only to MS supporting the R-GSM or ER -GSM frequency band.
This test is performed either on an outdoor test site, fulfilling the requirements of [GC4 of annex 1], or in an anechoic shielded chamber, fulfilling the requirements of ([GC5 of annex 1)]. Performing the measurement in the anechoic shie... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.1 MS allocated a channel | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.1.1 Definition | Radiated spurious emissions, when the MS has been allocated a channel, are any emissions radiated by the cabinet and structure of the mobile station, including all interconnecting cables.
This is also known as "cabinet radiation".
The test applies to all types of MS with the exception of the test at extreme voltages fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.1.2 Conformance requirement | 1. The radiated spurious power emitted by the MS, when allocated a channel, shall be no more than the levels in table 1217 under normal voltage conditions; 3GPP TS 05.05, subclauses 4.3 and 4.3.3.
2. The radiated spurious power emitted by the MS, when allocated a channel, shall be no more than the levels in table 12.17... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.1.3 Test purpose | 1. To verify that radiated spurious emissions from the MS when allocated a channel do not exceed the conformance requirements under normal voltage conditions.
2. To verify that radiated spurious emissions from the MS when allocated a channel do not exceed the conformance requirements under extreme voltage conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.1.4.1 Initial conditions | A call is set up by the SS according to the generic call set up procedure on a channel in the Mid ARFCN range.
NOTE: The power supply shall be connected to the MS such that the physical configuration does not change in a way that could have an effect on the measurement. In particular, the battery pack of the MS should ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.1.4.2 Procedure | a) Initially the test antenna is closely coupled to the MS and any spurious emission radiated by the MS is detected by the test antenna and receiver in the range 30 MHz to 4 GHz.
NOTE 0: This is a qualitative step to identify the frequency and presence of spurious emissions which are to be measured in subsequent steps.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.1.5 Test requirement | The power of any spurious emission shall not exceed the levels given in table 12.17. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.2 MS in idle mode | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.2.1 Definition | Radiated spurious emissions, when the MS is in idle mode, are any emissions radiated by the cabinet and structure of the mobile station, including all interconnecting cables.
This is also known as "cabinet radiation".
The test applies to all types of MS with the exception of the test at extreme voltages for an MS where... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.2.2 Conformance requirement | 1. The radiated spurious power emitted by the MS, when in idle mode, shall be no more than the levels in table 12.19. under normal voltage conditions; 3GPP TS 05.05, subclauses 4.3 and 4.3.3.
2. The radiated spurious power emitted by the MS, when in idle mode, shall be no more than the levels in table 12.19. under extr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.2.3 Test purpose | 1. To verify that radiated spurious emissions from the MS when in idle mode do not exceed the requirements under normal voltage conditions.
2. To verify that radiated spurious emissions from the MS when in idle mode do not exceed the requirements under extreme voltage conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.2.4.1 Initial conditions | NOTE 1: The power supply shall be connected to the MS such that the physical configuration does not change in a way that could have an effect on the measurement. In particular, the battery pack of the MS should not normally be removed. In cases where no practical connection can be made to the power supply, the MS's int... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.2.4.2 Procedure | a) Initially the test antenna is closely coupled to the MS and any spurious emission radiated by the MS is detected by the test antenna and receiver in the range 30 MHz to 4 GHz.
NOTE 1: This is a qualitative step to identify the frequency and presence of spurious emissions which are to be measured in subsequent steps.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 12.4.2.5 Test requirement | The power of any spurious emission shall not exceed the levels given in table 12.19. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13 Transmitter | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1 Frequency error and phase error | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.1 Definition | The frequency error is the difference in frequency, after adjustment for the effect of the modulation and phase error, between the RF transmission from the MS and either:
- the RF transmission from the BS; or
- the nominal frequency for the ARFCN used.
The phase error is the difference in phase, after adjustment for th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.2 Conformance requirement | 1. The MS carrier frequency shall be accurate to within 0,1 ppm, or accurate to within 0,1 ppm compared to signals received from the BS. For GSM 400 MS a value of 0,2 ppm shall be used in both cases.
1.1 Under normal conditions; 3GPP TS 05.10, subclause 6.1.
1.2 Under vibration conditions; 3GPP TS 05.10, subclause 6.1;... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.3 Test purpose | 1. To verify that the MS carrier frequency error does not exceed 0,1 ppm (0,2 ppm for GSM 400):
1.1 Under normal conditions.
1.2 When the MS is being vibrated.
1.3 Under extreme conditions.
NOTE: The transmit frequency accuracy of the SS is expected to be sufficient to ensure that the difference between 0,1 ppm (0,2 pp... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.4 Method of test | NOTE: In order to measure the accuracy of the frequency and phase error a sampled measurement of the transmitted phase trajectory is obtained. This is compared with the theoretically expected phase trajectory. The regression line of the difference between the expected trajectory and the measured trajectory is an indica... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.4.1 Initial conditions | A call is set up according to the Generic call setup procedure.
The SS commands the MS to hopping mode (table 6.1).
NOTE 1: It is not necessary to test in hopping mode but is done here as a simple means of making the MS change channel, it would be sufficient to test in non hopping mode and to make sure bursts are taken... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.4.2 Procedure | a) For one transmitted burst, the SS captures the signal as a series of phase samples over the period of the burst. These samples are evenly distributed over the duration of the burst with a minimum sampling rate of 2/T, where T is the modulation symbol period. The received phase trajectory is then represented by this ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.5 Test requirements | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.5.1 Frequency error | For all measured bursts, the frequency error, derived in step c.6), shall be less than 0,1 ppm, except for GSM 400 MS where a value of 0,2 ppm shall be used. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.1.5.2 Phase error | For all measured bursts, the RMS phase error, derived in step c.8), shall not exceed 5 degrees.
For all measured bursts, each individual phase error, derived in step c.7), shall not exceed 20 degrees.
13.1a Frequency error in VAMOS configuration
13.1a.1 Definition
The frequency error is the difference in frequency, aft... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.2 Frequency error under multipath and interference conditions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.2.1 Definition | The frequency error under multipath and interference conditions is a measure of the ability of the MS to maintain frequency synchronization with the received signal under conditions of Doppler shift, multipath reception and interference. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.2.2 Conformance requirement | 1. The MS carrier frequency error for each burst shall be accurate to within 0,1 ppm (0,2 ppm for GSM 400), or 0,1 ppm (0,2 ppm for GSM 400) compared to signals received from the BS for signal levels down to 3 dB below the reference sensitivity level.
1.1 Under normal conditions; 3GPP TS 05.10, subclauses 6 and 6.1.
1.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.2.3 Test purpose | 1. To verify that the MS carrier frequency error at reference sensitivity, under conditions of multipath and Doppler shift does not exceed 0,1 ppm (0,2 ppm for GSM 400) + the frequency error due to the Doppler shift of the received signal and the assessment error in the MS.
1.1 Under normal conditions.
1.2 Under extrem... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.2.4 Method of test | This test uses the same measurement process as test 13.1 for the MS operating under various RF conditions.
NOTE: The BA list sent on the BCCH and the SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCH but if they are provided no... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.2.4.1 Initial conditions | The MS is brought into the idle updated state on a serving cell with BCCH in the mid ARFCN range. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.2.4.2 Procedure | a) The level of the serving cell BCCH is set to 10 dB above the reference sensitivity level( ) and the fading function set to RA. The SS waits 30 s for the MS to stabilize to these conditions. The SS is set up to capture the first burst transmitted by the MS during call establishment. A call is initiated by the SS on ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.2.5 Test requirements | The frequency error, with reference to the SS carrier frequency as measured in repeats of step e), for each measured burst shall be less than the values shown in tables 13-1a and 13-1b.
Table 13-1a: Requirements for frequency error under multipath,
Doppler shift and interference conditions
T-GSM 810, GSM 850 and GSM 90... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3 Transmitter output power and burst timing | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.1 Definition | The transmitter output power is the average value of the power delivered to an artificial antenna or radiated by the MS and its integral antenna, over the time that the useful information bits of one burst are transmitted.
The transmit burst timing is the envelope of the RF power transmitted with respect to time. The t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.2 Conformance requirement | 1. The MS maximum output power shall be as defined in 3GPP TS 05.05, subclause 4.1.1, table for GMSK modulation, according to its power class, with a tolerance of ±2 dB under normal conditions; 3GPP TS 05.05, subclause 4.1.1, table for GMSK modulation.
2. The MS maximum output power shall be as defined in 3GPP TS 05.05... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.3 Test purpose | 1. To verify that the maximum output power of the MS, under normal conditions, is within conformance requirement 1.
2. To verify that the maximum output power of the MS, under extreme conditions, is within conformance requirement 2.
3. To verify that all nominal output power levels, relevant to the class of MS, are imp... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.4 Methods of test | Two methods of test are described, separately for:
1) equipment fitted with a permanent antenna connector or fitted with a temporary test connector as a test fixture, and for
2) equipment fitted with an integral antenna, and which cannot be connected to an external antenna.
NOTE: The behaviour of the MS in the system i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.4.1 Method of test for equipment with a permanent or temporary antenna connector | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.4.1.1 Initial conditions | A call is set up by the SS according to the generic call set up procedure on a channel with ARFCN in the Mid ARFCN range, power control level set to Max power. MS TXPWR_MAX_CCH is set to the maximum value supported by the Power Class of the Mobile under test. For DCS 1 800 mobile stations the POWER_OFFSET parameter is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.4.1.2 Procedure | a) Measurement of normal burst transmitter output power.
- The SS takes power measurement samples evenly distributed over the duration of one burst with a sampling rate of at least 2/T, where T is the bit duration. The samples are identified in time with respect to the modulation on the burst. The SS identifies the cen... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.4.2 Method of test for equipment with an integral antenna | NOTE: If the MS is equipped with a permanent connector, such that the antenna can be disconnected and the SS be connected directly, then the method of subclause 13.3.4.1 will be applied.
The tests in this subclause are performed on an unmodified test sample. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.4.2.1 Initial conditions | The MS is placed in the anechoic shielded chamber (annex 1, GC5) or on the outdoor test site, on an isolated support, in the position for normal use, at a distance of at least 3 metres from a test antenna, connected to the SS.
NOTE: The test method described has been written for measurement in an anechoic shielded cham... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.4.2.2 Procedure | a) With the initial conditions set according to subclause 13.3.4.2.1 the test procedure in subclause 13.3.4.1.2 is followed up to and including step i), except that in step a), when measurements are done at maximum power for ARFCN in the Low, Mid and High range, the measurement is made eight times with the MS rotated b... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.3.5 Test requirements | a) The transmitter output power, under every combination of normal and extreme test conditions, for normal bursts and access bursts, at each frequency and for each nominal output power level applicable to the MS power class, shall be at the relevant level shown in table 13-2, table 13-3 or table 13-4 within the toleran... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.4 Output RF spectrum | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.4.1 Definition | The output RF spectrum is the relationship between the frequency offset from the carrier and the power, measured in a specified bandwidth and time, produced by the MS due to the effects of modulation and power ramping. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.4.2 Conformance requirement | 1. The level of the output RF spectrum due to modulation shall be no more than that given in 3GPP TS 05.05, subclause 4.2.1, table a1) for GSM 400, GSM 700, T_GSM 810, GSM 850 and GSM 900, table B.1) for DCS 1 800 or table C.1) for PCS 1 900, with the following lowest measurement limits:
- -36 dBm below 600 kHz offset ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.4.3 Test purpose | 1. To verify that the output RF spectrum due to modulation does not exceed conformance requirement 1.
1.1 Under normal conditions.
1.2 Under extreme conditions.
2. To verify that the output RF spectrum due to switching transients does not exceed conformance requirement 2 when a reasonable margin is allowed for the effe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.4.4.1 Initial conditions | A call is set up according to the generic call set up procedure.
The SS commands the MS to hopping mode. The hopping pattern includes only three channels, namely one with an ARFCN in the Low ARFCN range, a second one with an ARFCN in the Mid ARFCN range and the third one with an ARFCN in the High ARFCN range.
NOTE 1: A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.4.4.2 Procedure | NOTE: When averaging is in use during frequency hopping mode, the averaging only includes bursts transmitted when the hopping carrier corresponds to the nominal carrier of the measurement.
a) In steps b) to h) the FT is equal to the hop pattern ARFCN in the Mid ARFCN range.
b) The other settings of the spectrum analyse... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.4.5 Test requirements | For absolute measurements, performed on a temporary antenna connector, in the frequency band 450,4 MHz to 457,6 MHz, 478,8 MHz to 486 MHz, 777 MHz to 792 MHz, 824 MHz to 849 MHz, 880 MHz to 915 MHz, 1 710 MHz to 1 785 MHz, or 1 850 MHz to 1 910 MHz, the temporary antenna connector coupling factor, determined according ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.5 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6 Frequency error and phase error in HSCSD multislot configurations | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.1 Definition | The frequency error is the difference in frequency, after adjustment for the effect of the modulation and phase error, between the RF transmission from the MS and either:
- the RF transmission from the BS; or
- the nominal frequency for the ARFCN used.
The phase error is the difference in phase, after adjustment for th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.2 Conformance requirement | 1. The MS carrier frequency shall be accurate to within 0,1 ppm, or accurate to within 0,1 ppm compared to signals received from the BS:
1.1 Under normal conditions; 3GPP TS 05.10, subclause 6.1.
1.2 Under vibration conditions; 3GPP TS 05.10, subclause 6.1; 3GPP TS 05.05, annex D D.2.3.
1.3 Under extreme conditions; 3G... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.3 Test purpose | 1. To verify that in a multislot configuration the MS carrier frequency error does not exceed 0,1 ppm:
1.1 Under normal conditions.
1.2 When the MS is being vibrated.
1.3 Under extreme conditions.
NOTE: The transmit frequency accuracy of the SS is expected to be sufficient to ensure that the difference between 0,1 ppm ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 2 To verify that the RMS phase error on the useful part of the bursts transmitted by the MS in a multislot configuration does not exceed conformance requirement 2: | 2.1 Under normal conditions.
2.2 When the MS is being vibrated.
2.3 Under extreme conditions.
3 To verify that the maximum phase error on the useful part of the bursts transmitted by the MS in a multislot configuration does not exceed conformance requirement 3.
3.1 Under normal conditions.
3.2 When the MS is being vibr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.4 Method of test | NOTE: In order to measure the accuracy of the frequency and phase error a sampled measurement of the transmitted phase trajectory is obtained. This is compared with the theoretically expected phase trajectory. The regression line of the difference between the expected trajectory and the measured trajectory is an indica... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.4.1 Initial conditions | A call is set up according to the generic call setup procedure for multislot HSCSD.
The SS commands the MS to hopping mode (table 13.6.1).
NOTE 1: It is not necessary to test in hopping mode but is done here as a simple means of making the MS change channel, it would be sufficient to test in non hopping mode and to mak... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.4.2 Procedure | a) For one transmitted burst on the last multislot subchannel, the SS captures the signal as a series of phase samples over the period of the burst. These samples are evenly distributed over the duration of the burst with a minimum sampling rate of 2/T, where T is the modulation symbol period. The received phase trajec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.5 Test requirements | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.5.1 Frequency error | For all measured bursts, the frequency error, derived in step c.6), shall be less than 10E-7. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.6.5.2 Phase error | For all measured bursts, the RMS phase error, derived in step c.8), shall not exceed 5 degrees.
For all measured bursts, each individual phase error, derived in step c.7), shall not exceed 20 degrees. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7 Transmitter output power and burst timing in HSCSD configurations | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.1 Definition | The transmitter output power is the average value of the power delivered to an artificial antenna or radiated by the MS and its integral antenna, over the time that the useful information bits of one burst are transmitted.
The transmit burst timing is the envelope of the RF power transmitted with respect to time. The t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.2 Conformance requirement | 1. The MS maximum output power shall be as defined in 3GPP TS 05.05, subclause 4.1.1, first table, according to its power class, with a tolerance of ±2 dB under normal conditions; 3GPP TS 05.05, subclause 4.1.1, first table. From R99 onwards, the MS maximum output power in an uplink multislot configuration shall be as ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 11 The MS shall use a TA value of 0 for the Random Access burst sent: | 11.1 Under normal conditions; 3GPP TS 05.10, subclause 6.6.
11.2 Under extreme conditions; 3GPP TS 05.10, subclause 6.6, 3GPP TS 05.05 annex D in subclauses D.2.1 and D.2.2.
3GPP TS 45.05 subclause 2:
For T-GSM 810 the requirements for GSM 900 shall apply, apart for those parameters for which a separate requirement exi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.3 Test purpose | 1. To verify that the maximum output power of the MS in HSCSD multislot configuration, under normal conditions, is within conformance requirement 1.
2. To verify that the maximum output power of the MS in HSCSD multislot configuration, under extreme conditions, is within conformance requirement 2.
3. To verify that all... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.4 Methods of test | Two methods of test are described, separately for:
1) equipment fitted with a permanent antenna connector or fitted with a temporary test connector as a test fixture, and for
2) equipment fitted with an integral antenna, and which cannot be connected to an external antenna.
NOTE: The behaviour of the MS in the system i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.4.1 Method of test for equipment with a permanent or temporary antenna connector | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.4.1.1 Initial conditions | A call is set up by the SS according to the generic call set up procedure for HSCSD multislot configuration on a channel with ARFCN in the Mid ARFCN range, power control level set to Max power and MS to operate in its highest number of uplink slots. MS TXPWR_MAX_CCH is set to the maximum value supported by the Power Cl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.4.1.2 Procedure | a) Measurement of normal burst transmitter output power.
The SS takes power measurement samples evenly distributed over the duration of one burst with a sampling rate of at least 2/T, where T is the bit duration. The samples are identified in time with respect to the modulation on the burst. The SS identifies the centr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.4.2 Method of test for equipment with an integral antenna | NOTE: If the MS is equipped with a permanent connector, such that the antenna can be disconnected and the SS be connected directly, then the method of subclause 13.7.4.1 will be applied.
The tests in this subclause are performed on an unmodified test sample. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.4.2.1 Initial conditions | The MS is placed in the anechoic shielded chamber (annex 1, GC5) or on the outdoor test site, on an isolated support, in the position for normal use, at a distance of at least 3 metres from a test antenna, connected to the SS.
NOTE: The test method described has been written for measurement in an anechoic shielded cham... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.4.2.2 Procedure | a) With the initial conditions set according to subclause 13.7.4.2.1 the test procedure in subclause 13.7.4.1.2 is followed up to and including step j), except that in step a), when measurements are done at maximum power for ARFCN in the Low, Mid and High range, the measurement is made eight times with the MS rotated b... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.7.5 Test requirements | a) The transmitter output power on each subchannel, under every combination of normal and extreme test conditions, for normal bursts and access bursts, at each frequency and for each power control level applicable to the MS power class, shall be at the relevant level shown in table 13.7-1, table 13.7-2 or table 13.7-3 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.8 Output RF spectrum in HSCSD multislot configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.8.1 Definition | The output RF spectrum is the relationship between the frequency offset from the carrier and the power, measured in a specified bandwidth and time, produced by the MS due to the effects of modulation and power ramping. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.8.2 Conformance requirement | 1. The level of the output RF spectrum due to modulation shall be no more than that given in 3GPP TS 05.05, 4.2.1, table a) for GSM 400, GSM 700, GSM 850 and GSM 900, table b) for DCS 1 800 or table c) for PCS 1 900, with the following lowest measurement limits:
- -36 dBm below 600 kHz offset from the carrier;
- -51 dB... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.8.3 Test purpose | 1. To verify that the output RF spectrum due to modulation does not exceed conformance requirement 1 in the multislot configurations.
1.1 Under normal conditions.
1.2 Under extreme conditions.
2. To verify that the output RF spectrum due to switching transients does not exceed conformance requirement 2 in the multislot... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.8.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.8.4.1 Initial conditions | A call is set up according to the generic call set up procedure for multislot HSCSD.
The SS commands the MS to hopping mode. The hopping pattern includes only three channels, namely one with an ARFCN in the Low ARFCN range, a second one with an ARFCN in the Mid ARFCN range and the third one with an ARFCN in the High AR... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.8.4.2 Procedure | NOTE: When averaging is in use during frequency hopping mode, the averaging only includes bursts transmitted when the hopping carrier corresponds to the nominal carrier of the measurement.
a) In steps b) to h) the FT is equal to the hop pattern ARFCN in the Mid ARFCN range.
b) The other settings of the spectrum analyse... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.8.5 Test requirements | For absolute measurements, performed on a temporary antenna connector, in the frequency band 450,4 MHz to 457,6 MHz, 478,8 MHz to 486 MHz, 777 MHz to 792 MHz, 824 MHz to 849 MHz, 880 MHz to 915 MHz, 1 710 MHz to 1 785 MHz or 1 850 MHz to 1 910 MHz, the temporary antenna connector coupling factor, determined according t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.9 Output RF spectrum for MS supporting the R-GSM or ER-GSM frequency band | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.9.1 Definition | The output RF spectrum is the relationship between the frequency offset from the carrier and the power, measured in a specified bandwidth and time, produced by the MS due to the effects of modulation and power ramping. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.9.2 Conformance requirement | 1. The level of the output RF spectrum due to modulation shall be no more than that given in 3GPP TS 05.05, subclause 4.2.1, table a) for R-GSM 900 and ER-GSM 900 with the following lowest measurement limits:
- -36 dBm below 600 kHz offset from the carrier;
- -51 dBm for R-GSM 900 and ER-GSM 900 from 600 kHz out to les... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 13.9.3 Test purpose | 1. To verify that the output RF spectrum due to modulation does not exceed conformance requirement 1.
1.1 Under normal conditions.
1.2 Under extreme conditions.
2. To verify that the output RF spectrum due to switching transients does not exceed conformance requirement 2 when a reasonable margin is allowed for the effe... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.