hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.9.4.2 Procedure | a) The fading function is set to TUhigh.
b) the SS sets the amplitude of the wanted signal to reference sensitivity level ( ).
c) The SS compares the data of the signal that it sends to the MS with the signal which is looped back from the receiver after demodulation and decoding, and checks the frame erasure indication... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.9.5 Test requirements | The error rates measured for different channels and under the different propagation conditions, under any combination of normal and extreme test voltages and ambient temperatures, shall not exceed the test limit error rate values given in table 14-5b.
Table 14-5b: Limits for GSM 900 sensitivity
Channels
Propagation con... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.10 Reference sensitivity - TCH/AFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.10.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved.
For E-GSM 900 MS this test is only performed in the P-GSM band. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.10.2 Conformance requirement | 1. At reference sensitivity level, the TCH/AFS FER shall meet the reference sensitivity performance of table 1 in 3GPP TS 05.05 subclause 6.2.
2. At reference sensitivity level, the TCH/AFS class Ib RBER shall meet the reference sensitivity, performance of table 1 in 3GPP TS 05.05 subclause 6.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.10.3 Test purpose | NOTE: This test is not performed under STATIC propagation conditions because the performance requirements are too small to be accurately measured.
1. To verify that the MS does not exceed conformance requirement 1 under TUhigh propagation conditions with an allowance for the statistical significance of the test.
2. To ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.10.4 Method of test | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
NOTE 2: The ARFCN of any BCCH sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.10.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the Mid ARFCN range for GSM 400, GSM 700, T-GSM 810, GSM 850, DCS 1800 and PCS 1 900 and ARFCN 70 for GSM 900, power control level set to maximum power.
NOTE: For GSM 900 ARFCN 70 is tested since this is the 73rd harmonic of t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.10.4.2 Procedure | a) The fading function is set to TUhigh.
b) the SS sets the amplitude of the wanted signal to reference sensitivity level ( ).
c) The SS compares the data of the signal that it sends to the MS with the signal which is looped back from the receiver after demodulation and decoding, and checks the frame erasure indication... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.10.5 Test requirements | Testing the reference sensitivity performance is performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with BER/BLER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of the limit lines refe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.18 Reference sensitivity - TCH/AHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.18.1 Definition | The reference sensitivity level is the signal level at the MS receiver input at which a certain BER and FER for speech frames must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.18.2 Conformance requirement | 1. At reference sensitivity level, the TCH/AHS FER shall meet the reference sensitivity performance of table 1 in 3GPP TS 05.05 subclause 6.2.
2 At reference sensitivity level, the TCH/AHS class Ib RBER (BFI=0) shall meet the reference sensitivity performance of table 1 in 3GPP TS 05.05 subclause 6.2.
3 At reference se... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.18.3 Test purpose | 1. To verify that the MS does not exceed conformance requirement 1 under TUhigh propagation conditions with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under TUhigh propagation conditions with an allowance for the statistical significance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.18.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.18.4.1 Initial conditions | The BA list sent on the BCCH and SACCH indicates at least six surrounding cells, with at least one near to each band edge. It is not necessary to generate any of these BCCHs, but if provided, the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
The ARFCN of any BCCH shall not be co-chan... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.18.4.2 Procedure | a) The SS commands the MS to create traffic channel loop back signalling erased frames.
NOTE: Frames detected with BFI=1 are signalled as erased on the uplink.
b) The fading function is set to TUHigh.
c) The SS sets the amplitude of the wanted signal to reference sensitivity level ( ).
d) The SS compares the data of th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.18.5 Test requirements | Testing the reference sensitivity performance is performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with BER/BLER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.19 Reference sensitivity - TCH/AFS-INB | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.19.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain FER for in band signalling codewords or frames must be achieved.
For E-GSM 900 MS this test is only performed in the P-GSM band. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.19.2 Conformance requirement | 1. At reference sensitivity level, the TCH/AFS-INB FER shall meet the reference sensitivity performance of table 1 in 3GPP TS 45.005 subclause 6.2.
The delays associated with Loop I remain constant for all of the following circumstances:
- For a given MS implementation.
- For the duration of the MS being powered on.
3G... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.19.3 Test purpose | NOTE: This test is not performed under STATIC propagation conditions because the performance requirements are too small to be accurately measured.
1. To verify that the MS does not exceed conformance requirement 1 under TUhigh propagation conditions with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.19.4 Method of test | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
NOTE 2: The ARFCN of any BCCH sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.19.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the Mid ARFCN range for GSM 400, GSM 700, T-GSM 810, GSM 850, DCS 1800 and PCS 1 900 and ARFCN 70 for GSM 900, power control level set to maximum power.
NOTE: For GSM 900 ARFCN 70 is tested since this is the 73rd harmonic of t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.19.4.2 Procedure | a) The fading function is set to TUhigh.
b) The SS sets the amplitude of the wanted signal to reference sensitivity level ( ).
c) The SS shall change the Codec Mode Indication and Codec Mode Command to the neighbour mode every 22 speech frames (440 ms) by following a scanning pattern (1->2->3->4->4->3->2->1). CMI shoul... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.19.5 Test requirements | The frame error rates measured for different channels shall not exceed the test limit error rate values given in table 14.2.19-1 or 14.2.19-2.
Table 14.2.19-1: Limits for GSM 400, GSM 700, T-GSM 810, GSM 850 and GSM 900 sensitivity
Channels
Propagation conditions Tuhigh
Test limit
error rate %
Minimum No.
of samples
TC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.20 Reference sensitivity - TCH/AHS-INB | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.20.1 Definition | The reference sensitivity level is the signal level at the MS receiver input at which a certain FER for in band signalling codewords or frames must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.20.2 Conformance requirement | 1. At reference sensitivity level, the TCH/AHS-INB FER shall meet the reference sensitivity performance of table 1 in 3GPP TS 45.005 subclause 6.2.
The delays associated with Loop I remain constant for all of the following circumstances:
- For a given MS implementation.
- For the duration of the MS being powered on.
3G... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.20.3 Test purpose | 1. To verify that the MS does not exceed conformance requirement 1 under TUhigh propagation conditions with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.20.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.20.4.1 Initial conditions | The BA list sent on the BCCH and SACCH indicates at least six surrounding cells, with at least one near to each band edge. It is not necessary to generate any of these BCCHs, but if provided, the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
The ARFCN of any BCCH shall not be co-chan... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.20.4.2 Procedure | a) The SS commands the MS to loop back in band signalling codewords by closing a Loop I.
b) The fading function is set to TUhigh.
c) The SS sets the amplitude of the wanted signal to reference sensitivity level ( ).
d) The SS shall change the Codec Mode Indication and Codec Mode Command at to the neighbour mode every 2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.20.5 Test requirements | The error rates measured for different channels and under the different propagation conditions, shall not exceed the test limit error rate values given in table 14.2.20-1 or 14.2.20-2.
Table 14.2.20-1: Limits for GSM 400, GSM 700, T-GSM 810, GSM 850 and GSM 900 sensitivity
Channels
Propagation conditions TUhigh
Test li... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.21 Reference sensitivity – O-TCH/AHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.21.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.21.2 Conformance requirement | For 8-PSK modulated speech channels for AMR, associated control channels and inband signalling, the minimum input signal level for which the reference performance shall be met is specified in table 1g
For all classes of MS supporting 8-PSK speech channels, an additional +2 dB adjustment applies for 8-PSK modulated spee... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.21.3 Test purpose | To verify that the MS does not exceed conformance requirement for FER and class 1b RBER under HT100 propagation conditions with an allowance for the statistical significance of the test, for channel combinations O-TCH/AHS10.2 and O-TCH/AHS 5.15 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.21.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.21.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a O-TCH/AFS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 10,2 kbit/s.
The SS transmits Standard Test Signal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.21.4.2 Procedure | a) The fading function is set to HT100.
b) The SS sets the level of the wanted signal to that indicated by Clev in table 14.2.21-2 or 14.2.21-3.
c) The SS compares the data of the signal that it sends to the MS with the signal which is looped back from the receiver after demodulation and decoding, and checks the frame ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.21.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.22 Reference sensitivity – O-TCH/WFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.22.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.22.2 Conformance requirement | For 8-PSK modulated speech channels for AMR, associated control channels and inband signalling, the minimum input signal level for which the reference performance shall be met is specified in table 1g
For all classes of MS supporting 8-PSK speech channels, an additional +2 dB adjustment applies for 8-PSK modulated spee... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.22.3 Test purpose | To verify that the MS does not exceed conformance requirement for FER and class 1b RBER under HT100 propagation conditions with an allowance for the statistical significance of the test, for channel combinations O-TCH/WFS15.85 and O-TCH/WFS 6.60 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.22.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.22.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a O-TCH/WFS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 15,85 kbit/s.
The SS transmits Standard Test Signa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.22.4.2 Procedure | a) The fading function is set to HT100.
b) The SS sets the level of the wanted signal to that indicated by Clev in table 14.2.22-2 or 14.2.22-3. The level is corrected by the appropriate value in the table above.
c) The SS compares the data of the signal that it sends to the MS with the signal which is looped back from... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.22.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.23 Reference sensitivity – O-TCH/WHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.23.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.23.2 Conformance requirement | For 8-PSK modulated speech channels for AMR, associated control channels and inband signalling, the minimum input signal level for which the reference performance shall be met is specified in table 1g
For all classes of MS supporting 8-PSK speech channels, an additional +2 dB adjustment applies for 8-PSK modulated spee... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.23.3 Test purpose | To verify that the MS does not exceed conformance requirement for FER and class 1b RBER under HT100 propagation conditions with an allowance for the statistical significance of the test, for channel combinations O-TCH/WHS12.65 and O-TCH/WHS 8.85. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.23.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.23.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a O-TCH/WHS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 12,65 kbit/s.
The SS transmits Standard Test Signa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.23.4.2 Procedure | a) The fading function is set to HT100.
b) The SS sets the level of the wanted signal to that indicated by Clev in table 14.2.23-2 or 14.2.23-3. The level is corrected by the appropriate value in the table above.
c) The SS compares the data of the signal that it sends to the MS with the signal which is looped back from... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.23.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.24 Reference sensitivity - TCH/WFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.24.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved.
For E-GSM 900 MS this test is only performed in the P-GSM band. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.24.2 Conformance requirement | At reference sensitivity level, the TCH/WFS class Ib RBER shall meet the reference sensitivity, performance of table 1f in 3GPP TS 45.005 subclause 6.2.
At reference sensitivity level ,the TCH/WFS FER shall meet the reference performance stated in 3GPP TS 45.005 subclause 6.2.
The reference performance shall be:
For sp... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.24.3 Test purpose | 1. To verify that the MS does not exceed conformance requirement at the maximum implemented codec rate under propagation condition TUhigh (for GSM700, T-GSM 810, GSM 850, GSM 900, DCS 1800 and PCS 1900) with no frequency hopping, RAhigh with no frequency hoping (for GSM700, T-GSM 810, GSM 850 and GSM 900), HThigh with ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.24.4 Method of test | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
NOTE 2: The ARFCN of any BCCH sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.24.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/WFS with an ARFCN in the Mid ARFCN range for GSM700, T-GSM 810, GSM 850, DCS 1800 and PCS 1 900 and ARFCN 70 for GSM 900, power control level set to maximum power.
NOTE: For GSM 900 ARFCN 70 is tested since this is the 73rd harmonic of the 13 MHz ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.24.4.2 Procedure | a) The fading function is set to TUhigh.
b) the SS sets the amplitude of the wanted signal to reference sensitivity level from table 2f in TS 45.005 based on the current active codec set, fading function of the SS and band. The level shall be corrected by the value in the table above describing the reference performanc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.24.5 Test requirements | Testing the reference sensitivity performance is performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with BER/BLER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of the limit lines refe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.25 Reference sensitivity – Repeated FACCH/F | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.25.1 Definition | The reference sensitivity for control channels is the signal level at the MS receiver input at which a certain FER must be achieved.
14.2.25.2 Conformance requirement.
For Repeated Downlink FACCH and Repeated SACCH (see 3GPP TS 44.006), the minimum input signal level for which the reference performance shall be met is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.25.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.25.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the Low ARFCN range, power control level set to maximum power.
The SS shall use Repeated FACCH for command and response frames for the duration of the test.
Each pair of FACCHs are counted as a single sample.
The SS transmits St... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.25.4.2 Procedure | a) The fading function is set to TUhigh.
b) The SS sets the amplitude of the wanted signal to –104dBm + Corr, (where Corr is the correction factor from the table above)
c) The SS sends a Layer 3 message which does not require a Layer 3 response from the MS. Due to the low signal level the MS may not be able to acknowle... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.25.5 Test Requirements | The error rates measured shall not exceed the test limit error rate values given in table 14.2.25-2.
For more information on statistical testing of FER performance, especially the definitions of limit lines refer to Annex A7.
Table 14.2.25-1: Minimum test times due to TU high fading conditions
Full Rate 50 km/h
Frequen... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.26 Reference sensitivity – Repeated SACCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.26.1 Definition | The reference sensitivity for control channels is the signal level at the MS receiver input at which a certain FER must be achieved.
14.2.26.2 Conformance requirement.
For Repeated Downlink FACCH and Repeated SACCH (see 3GPP TS 44.006), the minimum input signal level for which the reference performance shall be met is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.26.4 Method of test | For details on Repeated SACCH Layer 1 test method, please refer to Annex 10. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.26.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the Low ARFCN range, power control level is set to maximum power.
The SS shall use Repeated SACCH for all SACCH block on the downlink for the duration of the test.
Each pair of SACCH blocks (i.e. one Repeated SACCH block-pair) s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.26.4.2 Procedure | a) The fading function is set to TUhigh/NoFH.
b) The SS sets the amplitude of the wanted signal to –104dBm + Corr, (where Corr is the correction factor from the table above).
c) Following the reception of the last burst of the MS UL SACCH corresponding to the second SACCH block of a repeated SACCH interval, the SS shal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.26.5 Test Requirements | The error rates measured shall not exceed the test limit error rate values given in table 14.2.26-2.
For more information on statistical testing of FER performance, especially the definitions of limit lines refer to Annex A7.
Table 14.2.25-1: Minimum test times due to TU high fading conditions
Full Rate 50 km/h
Frequen... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.27 Reference sensitivity - TCH/FS – DARP Phase II | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.27.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.27.2 Conformance requirement | For Downlink Advanced Receiver Performance – phase II, the minimum input signal level for which the reference performance shall be met is specified in table 1j, according to the propagation condition and type of equipment. The performance requirements for GSM 400 and GSM 700 systems are as for GSM 900 in table 1j, exce... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.27.3 Test purpose | To verify that the MS supporting DARP Ph2 does not exceed conformance requirement for FER, Rber1b and Rber2 under TUhigh/(Corr.=0,AGI=0) and HThigh/(Corr.=0,7,AGI=-6dB) propagation conditions with an allowance for the statistical significance of the test, for channel combination TCH/FS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.27.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.27.4.1 Initial conditions | Connect the SS to the MS antenna connectors according to Annex A1.1.6.
A call is set up according to the generic call set up procedure on a TCH/FS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.The SS transmits Standard Test Signal C1 on the traffic ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.27.4.2 Procedure | a) The fading function is set to TU high/(Corr.=0, AGI=0).
b) the SS sets the amplitude of the wanted signal to reference sensitivity level from table 1j in TS 45.005.
c) The SS compares the data of the signal that it sends to the MS with the signal which is looped back from the receiver after demodulation and decoding... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.27.5 Test requirements | The error rates measured shall not exceed the test limit error rate values given in table 14.2.27-3 through 14.2.27-6.
For more information on statistical testing of FER and BER/BLER performance, especially the definition of limit lines refer to Annex A7.
Table 14.2.27-1: Minimum test times due to TU high fading condit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.28 Reference sensitivity TCH/HS in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.28.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.28.2 Conformance requirement | The reference performance in VAMOS Mode, shall be
- For half rate speech channels (TCH/HS, TCH/AHSx) FER: 1 %
3GPP TS 45.005 subclause 6.2.1a
For speech channels in VAMOS Mode, and their associated control channels, the minimum input signal level for which the reference performance shall be met is specified in tabl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.28.3 Test purpose | 1. To verify that the MS does not exceed conformance requirements under propagation condition TUhigh with no frequency hopping with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.28.4 Method of test | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
NOTE 2: The ARFCN of any BCCH sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.28.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/HS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using trainin... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.28.4.2 Procedure | a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) The SS sets SCPIR_DL to +4 dB.
c) Depending of the indicated VAMOS type and the relevant antenna correlation and antenna gain imbal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.28.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2).
Before limi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.29 Reference sensitivity TCH/EFS in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.29.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.29.2 Conformance requirement | The reference performance in VAMOS Mode, shall be
- For full rate speech channels (TCH/FS, TCH/AFSx, TCH/EFS, TCH/WFSx ) FER: 1 %
3GPP TS 45.005 subclause 6.2.1a
For speech channels in VAMOS Mode, and their associated control channels, the minimum input signal level for which the reference performance shall be met i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.29.3 Test purpose | 1. To verify that the MS does not exceed conformance requirements under propagation condition TUhigh with no frequency hopping with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.29.4 Method of test | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
NOTE 2: The ARFCN of any BCCH sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.29.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/EFS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using traini... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.