hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.29.4.2 Procedure | a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) The SS sets SCPIR_DL to +4 dB.
c) Depending of the indicated VAMOS type and the relevant antenna correlation and antenna gain imbal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.29.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.30 Reference sensitivity TCH/AFS in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.30.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.30.2 Conformance requirement | The reference performance in VAMOS Mode, shall be
- For full rate speech channels (TCH/FS, TCH/AFSx, TCH/EFS, TCH/WFSx ) FER: 1 %
3GPP TS 45.005 subclause 6.2.1a
For speech channels in VAMOS Mode, and their associated control channels, the minimum input signal level for which the reference performance shall be met i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.30.3 Test purpose | 1. To verify that the MS does not exceed conformance requirements under propagation condition TUhigh with no frequency hopping with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.30.4 Method of test | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
NOTE 2: The ARFCN of any BCCH sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.30.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 12.20 kbit/s.
The SS transmits a Standard Test Signal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.30.4.2 Procedure | a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) The SS sets SCPIR_DL to +4 dB.
c) Depending of the indicated VAMOS type and the relevant antenna correlation and antenna gain imbal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.30.5 Test requirements | Testing the reference sensitivity performance is performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with BER/BLER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of the limit lines refe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.31 Reference sensitivity TCH/AHS in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.31.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.31.2 Conformance requirement | The reference performance in VAMOS Mode, shall be
- For half rate speech channels (TCH/HS, TCH/AHSx) FER: 1 %
3GPP TS 45.005 subclause 6.2.1a
For speech channels in VAMOS Mode, and their associated control channels, the minimum input signal level for which the reference performance shall be met is specified in tabl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.31.3 Test purpose | 1. To verify that the MS does not exceed conformance requirements under propagation condition TUhigh with no frequency hopping with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.31.4 Method of test | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
NOTE 2: The ARFCN of any BCCH sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.31.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 7.4 kbit/s.
The SS transmits a Standard Test Signal C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.31.5 Test requirements | Testing the reference sensitivity performance is performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with BER/BLER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of the limit lines refe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.32 Reference sensitivity TCH/WFS in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.32.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved.
For E-GSM 900 MS this test is only performed in the P-GSM band. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.32.2 Conformance requirement | 1. At reference sensitivity level, the TCH/WFS FER shall meet the reference performance stated in 3GPP TS 45.005 subclause 6.2.1.a
The reference performance shall be:
For speech channels (TCH/WFSy) FER £ 1%
2. For MS supporting VAMOS I, at reference sensitivity level, the TCH/WFS class Ib RBER shall meet the reference ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.32.3 Test purpose | 1. To verify that the MS does not exceed conformance requirements under propagation condition TUhigh with no frequency hopping with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.32.4 Method of test | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ).
NOTE 2: The ARFCN of any BCCH sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.32.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/WFS with an ARFCN in the Mid ARFCN range for GSM700, T-GSM 810, GSM 850, DCS 1800 and PCS 1 900 and ARFCN 70 for GSM 900, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
NOTE: For GSM 900 ARFCN 70 is tested since th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.32.4.2 Procedure | a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) The SS sets SCPIR_DL to +4 dB.
c) Depending of the indicated VAMOS type and the relevant antenna correlation and antenna gain imbal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.32.5 Test requirements | Testing the reference sensitivity performance is performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with BER/BLER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of the limit lines refe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.33 Reference sensitivity FACCH/F performance in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.33.1 Definition | The reference sensitivity for control channels is the signal level at the MS receiver input at which a certain FER must be achieved.
14.2.33.2 Conformance requirement.
1. For MS supporting VAMOS I, at reference sensitivity level, the FACCH/F FER shall meet the reference sensitivity, performance of table 1s in 3GPP TS 4... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.33.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.33.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the Low ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using training... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.33.4.2 Procedure | a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) The SS sets SCPIR to +4 dB.
c) Depending of the indicated VAMOS type and the relevant antenna correlation and antenna gain imbalanc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.33.5 Test Requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.34 Reference sensitivity – FACCH/H Performance in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.34.1 Definition | The reference sensitivity for control channels is the signal level at the MS receiver input at which a certain FER must be achieved.
14.2.34.2 Conformance requirement.
The reference performance in VAMOS Mode shall be:
- For full rate speech channels (TCH/FS, TCH/AFSx, TCH/EFS, TCH/WFSx ) FER: 1 %
- For half rate sp... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.34.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.34.4.1 Initial conditions | A call is set up according to the generic call set up procedure on TCH/HS or any TCH/AHS, whichever supported by the MS, with an ARFCN in the Mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.34.4.2 Procedure | a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) The SS sets SCPIR to +4 dB.
c) Depending of the indicated VAMOS type and the relevant antenna correlation and antenna gain imbalanc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.34.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.35 Reference sensitivity SACCH performance in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.35.1 Definition | The reference sensitivity for control channels is the signal level at the MS receiver input at which a certain FER must be achieved.
14.2.35.2 Conformance requirement.
3GPP TS 45.005 subclause 6.2.1a
The reference performance in VAMOS Mode shall be:
For signalling channels (FACCH/F, FACCH/H, SACCH) FER: 5 %
For spe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.35.3 Test purpose | To verify that the MS does not exceed the conformance requirement under TUhigh propagation condition with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.35.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.35.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the Low ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using training... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.35.4.2 Procedure | Note: The test procedure is derived from 51.010-10 annex 10 and adapted to single SACCH reception.
a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) The SS sets SCPIR_DL to +4 dB.
c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.35.5 Test Requirements | Testing should be performed using statistical methods that could lead to an early pass/fail decision with test time significantly reduced for MS with FER not on the limit.
For information on statistical testing refer to Annex 7 (A7.1.3.2).
Before limit checking is valid the minimum test time due to fading needs to be c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.36 Reference sensitivity – Repeated SACCH in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.36.1 Definition | The reference sensitivity for control channels is the signal level at the MS receiver input at which a certain FER must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.36.2 Conformance requirement | - The reference performance for the Repeated Associated control channel performance in VAMOS mode shall be according to subclause 6.2.4.
3GPP TS 45.005 subclause 6.2.1a
- For Repeated Downlink FACCH and Repeated SACCH (see 3GPP TS 44.006), the minimum input signal level for which the reference performance shall be met ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.36.4 Method of test | For details on Repeated SACCH Layer 1 test method, please refer to Annex 10. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.36.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using tr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.36.4.2 Procedure | a) The fading profile is set to TU50/NoFH for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) Depending on the indicated VAMOS type and the relevant antenna correlation and antenna gain imbalance values, the SS sets the lev... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.36.5 Test Requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER not on the limit.
For information on statistical testing refer to Annex 7 (A7.1.3.2)
Before limit checking is valid the minimum test time due to fading needs to be consider... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.37 Reference sensitivity – Repeated FACCH/F in VAMOS configuration | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.37.1 Definition | The reference sensitivity for control channels is the signal level at the MS receiver input at which a certain FER must be achieved.
14.2.37.2 Conformance requirement.
- The reference performance for the Repeated Associated control channel performance in VAMOS mode shall be according to subclause 6.2.4.
3GPP TS 45.005 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.37.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.37.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the Mid ARFCN range, power control level set to maximum power.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using trainings sequence 5 form TSC set 2. The other... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.37.4.2 Procedure | a) The fading function is set to TU50 /NoFH for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) Depending on the indicated VAMOS type and the relevant antenna correlation and antenna gain imbalance values, the SS sets the l... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.2.37.5 Test Requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER not on the limit.
For information on statistical testing refer to Annex 7 (A7.1.3.2)
Before limit checking is valid the minimum test time due to fading needs to be consider... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.3 Usable receiver input level range | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.3.1 Definition | The usable receiver input level range is the range of the radio frequency input level of a specified modulated signal over which bit error ratio or frame erasure ratios stay between specified limits. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.3.2 Conformance requirement | 1. The receiver input level range requirements of 3GPP TS 05.05 subclause 6.1 for TCH/FS class II RBER under static and EQ propagation conditions shall be met:
1.1 Under normal conditions.
1.2 Under extreme conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.3.3 Test purpose | 1. To verify that the MS does not exceed the conformance requirement with an allowance for the statistical significance of the test:
1.1 Under normal conditions.
1.2 Under extreme conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.3.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/FS with an ARFCN in the Mid ARFCN range, power control level set to maximum.
The SS transmits Standard Test Signal C1 on the TCH/FS.
The SS commands the MS to create traffic channel loop back signalling erased frames (subclause 36.2.1.1.2). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.3.4.2 Procedure | a) The SS compares the data that it sends to the MS with the signal which is looped back from the receiver after demodulation and decoding.
The SS tests the bit error ratio for the non-protected bits of TCH/FS class II, by examining sequences of at least the minimum number of samples of consecutive bits of class II. Th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.3.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate values given in table 14-14. This shall apply for any combination of normal and extreme test voltages and ambient temperature, for the different propagation conditions and for any level of input signal to the receiver.
Table 14-14: Limits f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4 Co-channel rejection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.1 Co-channel rejection - TCH/FS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.1.1 Definition | The co-channel rejection is a measure of the capability of the receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of an unwanted modulated signal, both signals being at the nominal frequency of the receiver. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.1.2 Conformance requirement | 1. At reference co-channel interference the TCH/FS FER shall meet the reference interference performance of table 2 in 3GPP TS 05.05 subclause 6.3.
2. At reference co-channel interference the TCH/FS class Ib BER shall meet the reference interference performance of table 2 in 3GPP TS 05.05 subclause 6.3.
3. At reference... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.1.3 Test purpose | 1. To verify that the MS does not exceed conformance requirement 1 under propagation condition TUlow with no frequency hopping with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under propagation condition TUlow with no frequency hopping, w... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/FS with an ARFCN in the mid ARFCN range, power control level set to maximum power.
The SS transmits Standard Test Signal C1 on the traffic channel (wanted signal).
The SS commands the MS to create the traffic channel loop back, signalling erased f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.1.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. Its amplitude is 9 dB below that of the wanted signal.
The fa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.1.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate values given in table 14-15.
Table 14-15: Limits for co-channel rejection
Channel
Type of measurement
Propagation condition
Test limit error rate %
Minimum No. of samples
TCH/FS
FER
TUlow/No FH
24*
25 000
TCH/FS Class Ib
RBER
TUlow/No FH
2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.2 Co-channel rejection - TCH/HS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.2.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.2.2 Conformance requirement | 1. At reference co channel interference, the TCH/HS FER (shall meet the reference interference performance of table 2 in 3GPP TS 05.05 subclause 6.3.
2. At reference co channel interference, the TCH/HS class Ib BER (BFI=0) shall meet the reference interference performance of table 2 in 3GPP TS 05.05 subclause 6.3.
3. A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.2.3 Test purpose | 1. To verify that the MS does not exceed conformance requirement 1, under propagation conditions TUhigh with frequency hopping, with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 1, under propagation conditions TUhigh with frequency hopping, ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/HS with an ARFCN in the mid ARFCN range, power control level set to maximum power.
The SS transmits Standard Test Signal C1 on the traffic channel (wanted signal). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.2.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. Its amplitude is 9 dB below that of the wanted signal.
b) The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.2.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate values given in table 14-16 or table 14-17.
Table 14-16: Limits for GSM 400, GSM 700, T-GSM 810, GSM 850 and GSM 900 co-channel rejection
Channel/Type of measurement
Propagation condition
Test limit error rate %
Minimum No. of samples
TCH/H... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.4 Co-channel rejection - FACCH/F | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.4.1 Definition | The co-channel rejection is a measure of the capability of the receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of an unwanted modulated signal, both signals being at the nominal frequency of the receiver. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.4.2 Conformance requirement | At reference co channel interference the FACCH/F FER shall meet the reference interference performance of table 2 in 3GPP TS 05.05 subclause 6.3). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.4.3 Test purpose | To verify that the MS does not exceed the conformance requirement under propagation condition TUlow with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.4.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the mid ARFCN range. The power control level is set to maximum power.
The SS transmits Standard Test Signal C1 on the traffic channel (wanted signal). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.4.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. Its amplitude is 9 dB below that of the wanted signal.
The fadin... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.4.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate values given in table 14-19.
Table 14-19: Limits for co-channel rejection
Channel
Type of measurement
Propagation condition
Test limit error rate %
Minimum No. of samples
FACCH/F
FER
TUlow/No FH
24
25 000
14.4.4a Co-channel rejection - FACC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.5 Co-channel rejection - FACCH/H | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.5.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.5.2 Conformance requirement | At reference co channel interference the FACCH/H FER shall meet the reference interference performance of table 2 in 3GPP TS 05.05 subclause 6.3). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.5.3 Test purpose | To verify that the MS does not exceed the conformance requirement under propagation condition TUlow with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.5.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH with an ARFCN in the mid ARFCN range. For MS supporting half rate speech this shall be a TCH/HS. For MS not supporting TCH/HS one of the supported TCH/(AHS, H4,8, or H2,4) shall be used. The power control level is set to maximum power.
The SS tran... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.5.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. Its amplitude is 9 dB below that of the wanted signal.
The fadin... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.5.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate values given in table 14-20.
Table 14-20: Limits for co-channel rejection
Channel
Type of measurement
Propagation condition
Test limit error rate %
Minimum No. of samples
FACCH/H
FER
TUlow/No FH
24,000
25 000
14.4.5a Co-channel rejection - ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.4.6 Co-channel rejection - TCH/EFS |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.