hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 18.2.1 Definition | A temporary reception gap is a limited period of time in which the RF reception is interrupted. During this gap the MS shall maintain the frequency and timing of its transmission within specifications. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 18.2.2 Conformance requirement | 1) During a temporary total loss of signal, of up to 64 SACCH block periods, the MS shall update its timebase with a clock which is accurate to within 0,2 ppm, or to within 0,2 ppm of the signals previously received from the BTS. The MS shall use the same frequency source for both RF frequency generation and clocking t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 18.2.3 Test purpose | 1) To verify that, during a temporary total loss of signal of up to 63 SACCH block periods on the main multislot channel, the MS carrier frequency is accurate to within 0,2 ppm of the signals previously received from the BTS.
2) To verify that, the MS transmissions to the BTS, measured at the MS antenna, is 3 timeslots... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 18.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 18.2.4.1 Initial conditions | The SS signals RADIO_LINK_TIMEOUT = 64 and "DTX OFF" on the BCCH.
The MS is brought into MM state "idle, updated".
After 10 s, the SS continues to set up a call according to the generic call set up procedure for multislot HSCSD.
The SS commands the MS to operate in a highest possible asymmetric configuration, with a ma... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 18.2.4.2 Procedure | a) The SS, in a TDMA frame immediately following the transmission of a complete SACCH block, removes the downlink signal for 63 SACCH blocks of the main channel.
NOTE: This gives the maximum temporary reception gap.
b) The SS measures the frequency and timing of the MS transmissions immediately before, and at least 5 t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 18.2.5 Test requirement | 1) The MS carrier frequency shall be accurate to within 0,2 ppm compared to signals received from the SS.
2) The receive/transmit delay timing shall be 3 timeslots ± 1 bit.
3) During the second reception gap the MS shall maintain transmission for a period up to but not exceeding 3 SACCH blocks.
4) During the first, max... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19 Channel release after unrecoverable errors | NOTE: It is not possible to explicitly verify the correct functioning of all aspects of the radio link failure algorithm in the MS. Therefore 3 tests are used to implicitly verify correct implementation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.1 Channel release after unrecoverable errors - 1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.1.1 Definition | Channel release after unrecoverable errors is a procedure to abort the call if the radio link has been severely corrupted for some time, according to a link failure criterion. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.1.2 Conformance requirement | 1) If the MS is unable to decode a SACCH message, the radio link counter S is decreased by 1. In the case of a successful reception of a SACCH message S is increased by 2. In any case S shall not exceed the value of RADIO_LINK_TIMEOUT. If S reaches 0 a radio link failure shall be declared.
3GPP TS 05.08, subclause 5.2.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.1.3 Test purpose | 1) To verify correct handling of the radio link counter S.
2) To verify that the MS that is transmitting continues to transmit as normal on the uplink until S reaches 0.
3) To verify that the algorithm starts after the assignment of a dedicated channel, with S initialized to RADIO_LINK_TIMEOUT.
4) To verify that the MS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.1.4.1 Initial conditions | The SS sends a default value for the parameter RADIO_LINK_TIMEOUT on the BCCH. CALL RE-ESTABLISHMENT is not allowed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.1.4.2 Procedure | a) A MS terminated call is set up according to the generic call set up procedure. The SS sends a randomly choosen value N for the parameter RADIO_LINK_TIMEOUT on SACCH (System Information Type 6). This must be different than that sent on the BCCH.
b) The SS sends 32 error free SACCH messages, followed by N SACCH messag... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.1.5 Test requirement | After receiving the N SACCH messages with unrecoverable errors, the MS shall abort the RR-connection, i.e. there is no more MS activity on the SACCH channel. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.2 Channel release after unrecoverable errors - 2 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.2.1 Definition | Channel release after unrecoverable errors is a procedure to abort the call if the radio link has been severely corrupted for some time, according to a link failure criterion. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.2.2 Conformance requirement | 1) If the MS is unable to decode a SACCH message, the radio link counter S is decreased by 1. In the case of a successful reception of a SACCH message S is increased by 2. In any case S shall not exceed the value of RADIO_LINK_TIMEOUT. If S reaches 0 a radio link failure shall be declared.
3GPP TS 05.08, subclause 5.2.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.2.3 Test purpose | 1) To verify correct handling of the radio link counter S.
2) To verify that the MS that is transmitting continues to transmit as normal on the uplink until S reaches 0.
3) To verify that the algorithm starts after the assignment of a dedicated channel, with S initialized to RADIO_LINK_TIMEOUT. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.2.4.1 Initial conditions | The SS sends a default value for the parameter RADIO_LINK_TIMEOUT on the BCCH. CALL RE-ESTABLISHMENT is not allowed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.2.4.2 Procedure | a) A MS terminated call is set up according to the generic call set up procedure. The SS sends a randomly choosen value N for the parameter RADIO_LINK_TIMEOUT on SACCH (System Information Type 6). This must be different than that sent on the BCCH.
b) The SS sends 2 SACCH messages with unrecoverable errors followed by o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.2.5 Test requirement | The MS shall not abort the RR-connection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.3 Channel release after unrecoverable errors - 3 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.3.1 Definition | Channel release after unrecoverable errors is a procedure to abort the call if the radio link has been severely corrupted for some time, according to a link failure criterion. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.3.2 Conformance requirements | 1) If the MS is unable to decode a SACCH message, the radio link counter S is decreased by 1. In the case of a successful reception of a SACCH message S is increased by 2. In any case S shall not exceed the value of RADIO_LINK_TIMEOUT. If S reaches 0 a radio link failure shall be declared.
3GPP TS 05.08, subclause 5.2.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.3.3 Test purpose | 1) To verify correct handling of the radio link counter S.
2) To verify that the MS that is transmitting continues to transmit as normal on the uplink until S reaches 0.
3) To verify that the algorithm starts after the assignment of a dedicated channel, with S initialized to RADIO_LINK_TIMEOUT.
4) To verify that the MS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.3.4.1 Initial conditions | The SS sends a default value for the parameter RADIO_LINK_TIMEOUT on the BCCH. CALL RE_ESTABLISHMENT is not allowed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.3.4.2 Procedure | a) A MS terminated call is set up according to the generic call set up procedure. The SS sends a randomly choosen value N for the parameter RADIO_LINK_TIMEOUT on SACCH (System Information Type 6) . This must be different than that sent on the BCCH.
b) The SS sends 32 error free SACCH messages, followed by 3 SACCH messa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 19.3.5 Test requirement | After receiving the 3 (N - 2) erroneous SACCH messages the MS shall abort the RR-connection, i.e. there is no more activity on the SACCH channel. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20 Cell selection and reselection | In the following paragraphs some explanatory text is given concerning the nature of the tests in this clause and the general behaviour of the SS is described.
Since the conformance requirements of most of the tests in this clause cannot be tested explicitly, testing is done implicitly by testing the MS behaviour from i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.1 Cell selection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.1.1 Definition | Cell selection is a process in which a MS, whenever a new PLMN is selected, attempts to find a suitable cell of that PLMN to camp on. Two methods of searching for a suitable cell are possible, normal cell selection and stored list cell selection. The process ensures that the MS is camped on a cell from which it can rel... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.1.2 Conformance requirement | 1. The MS shall be able to select the correct (fourth strongest) cell and be able to respond to paging on that cell within 30 s of switch on, when the three strongest cells are not suitable. This assumes a valid SIM, with PIN disabled and ideal radio conditions; 3GPP TS 05.08, subclause 6.1.
2. There are various requir... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.1.3 Test purpose | 1. To verify that the MS meets conformance requirement 1.
2. To verify that:
2.1 The MS does not select a cell of a PLMN which is not the selected PLMN.
2.2 The MS does not select a cell which is "barred".
2.3 The MS does not select a cell with C1 < 0.
3. To verify that the MS selects suitable cells in descending order... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.1.4.1 Initial conditions | Parameters changed from the default values in table 20.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
48 / -65
38 / -75
43 / -70
33 / -80
28 / -85
OFF
CBA
1
0
0
0
0
RXLEV_ACCESS_MIN
(dBm)
-90
-67
-90
-88
-98
MNC
See Table 20.1c
MCC
002
C1
25
-8
20
8
13
C2
25
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.1.4.2 Procedure | a) The SS activates the carriers and monitors carriers 2, 4 and 5 for RA requests from the MS.
b) The MS is switched on.
c) The MS is switched off.
d) The SS monitors carriers 1 and 3 for RA requests from the MS.
e) The MS is switched on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.1.5 Test requirements | 1) After step b), the first response from the MS shall be on carrier 4 within 33 s. There shall be no response from the MS on carrier 2.
2) After step e), there shall be no response from the MS on either carrier 1 or carrier 3 within 33 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.2 Cell selection with varying signal strength values | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.2.1 Definition | For definition see conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.2.2 Conformance requirement | 1. The MS shall:
The MS shall search all RF channels within its bands of operation, take readings of received RF signal level on each RF channel, and calculate the RLA_C for each. The averaging is based on at least five measurement samples per RF carrier spread over 3 to 5 s, the measurement samples from the different ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.2.3 Test purpose | 1. To verify that:
1.1 The MS meets conformance requirement 1.1.
1.2 The MS meets conformance requirement 1.2.
1.3 The MS meets conformance requirement 1.3.
2. To verify that the MS meets conformance requirement 2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.2.4.1 Initial conditions | Parameters changed from the default values in table 20.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
23 / -90
58 / -55
OFF
OFF
OFF
OFF
RXLEV_ACCESS_MIN
(dBV emf() / dBm)
13 / -100
13 / -100
C1
10
53
For an E-GSM MS carrier 1 ARFCN is chosen in the E-GSM ban... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.2.4.2 Procedure | a) The SS transmits on carriers 1 and 2. After a period of b Tav carrier 2 reduces its transmit level to ‑85 dBm (28 dBV emf( )). After a further period of a Tav, carrier 2 increases its transmit level again to ‑55 dBm (58 dBV emf( )). Switching of carrier 2 continues with these levels and duty cycle until the en... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.2.5 Test requirements | In step c), the first response from the MS shall be on carrier 2 within 33 s.
NOTE 1: With the selected duty cycle it can be guaranteed that a "good" MS passes the test even at the worst case situations. The minimum averaged value of carrier 2 is in any case higher or equal to -75 dBm which is still 6 dB above carrier ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.3 Basic cell reselection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.3.1 Definition | While camped on a cell of the selected PLMN the MS may need to select a different cell in order to fulfil the normal service state. This ensures that the MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.3.2 Conformance requirement | 1. While camped on a cell of the selected PLMN ("camped normally"), the MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
1.1 (iii) The cell camped on (current serving cell) has become barred.
1.2 (iv) There is a better cell (in terms of the path ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.3.3 Test purpose | 1. To verify that:
1.1 The MS meets conformance requirement 1.1.
1.2 The MS meets conformance requirement 1.2.
2. To verify that:
2.1 The MS does not reselect a cell which is barred.
2.2 The MS does not reselect a cell which has a C1 < 0.
3. To verify that the MS calculates the C2 parameter correctly when the CELL_RESE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.3.4.1 Initial conditions | Parameters changed from the default values in table 20.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
43 / -70
33 / -80
43 / -70
35 / -78
38 / -75
RXLEV_ACCESS_MIN (dBm)
-85
-90
-90
-85
-67
CRH
10 dB
LAC
different from other carriers
CBA
1
CBQ
0
C1
15
10
20
7... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.3.4.2 Procedure | a) The SS activates carriers 1, 2, 4 and 5. The MS is not paged on carrier 1. The SS monitors carriers 2, 4 and 5 for RA requests from the MS.
b) The MS is switched on.
c) The SS stops paging on all carriers except carrier 2. The level of carrier 2 is increased to 43 dBVemf (C2 becomes 20 dB), and the SS monitors carr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.3.5 Test requirements | 1) After step b), there shall be no response from the MS on carriers 2, 4, or 5 within 50 s.
2) In step c), the MS shall respond on carrier 2 within 20 s of increasing the level of carrier 2.
NOTE 1: 5 s to perform running average, 10 s to detect C2 differences, 2,4 s to read BCCH of carrier 2, 1 s to perform RA. Total... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.4 Cell reselection using TEMPORARY_OFFSET, CELL_RESELECT_OFFSET, POWER_OFFSET and PENALTY_TIME parameters | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.4.1 Definition | void |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.4.2 Conformance requirement | 1. The MS shall be able to calculate correctly the path loss criterion parameter C2 used for cell reselection; 3GPP TS 05.08, subclause 6.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.4.3 Test purpose | 1. To verify that the MS calculates the C2 parameter correctly when the CELL_RESELECT_OFFSET, TEMPORARY_OFFSET and PENALTY_TIME parameters are used.
2. To verify DCS 1 800 MS correctly calculate the C2 parameter when the POWER_OFFSET parameter is present. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.4.4.1 Initial conditions | Parameters changed from the default values in table 20.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
53 / -60
43 / -70
48 / -65
48 / -65
RXLEV_ACCESS_MIN (dBm)
-80
-100
-85
-85
PT
11111
40 s
60 s
CRO
16 dB
20 dB
20 dB
TO
20 dB
20 dB
K = 1
C1
20
30
20
20
C2
2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.4.4.2 Procedure | For testing of all types of MS, the test procedure is performed for execution counter K = 1.For testing of DCS 1 800 Class 3 MS, the test procedure is performed for execution counter K = 1 and 2:
On execution counter K = 1, the POWER_OFFSET Parameter is not present.
On execution counter K = 2, the POWER_OFFSET paramete... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.4.4.3 Requirements | For execution counter K = 1 and K = 2.
1) After step b), there shall be no response from the MS on carrier 2 within 50 s.
2) After step c), the MS shall respond on carrier 2 within 20 s of increasing the level of carrier 2.
3) After step e), there shall be no response from the MS on carrier 3 within 38 s of activating ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.5 Cell reselection using parameters transmitted in the System Information type 2bis, type 2ter, type 7 and type 8 messages | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.5.1 Definition | System information (SI) type 7 and 8 are transmitted on the BCCH Ext when the system information type 4 message does not contain all information needed for cell selection.
The system information type 2 bis message is used when the system information type 2 message does not contain all neighbour cell ARFCNs.
The system ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.5.2 Conformance requirement | 1. The MS shall be able to calculate correctly the path loss criterion parameter C2 used for cell reselection. 3GPP TS 05.08, subclause 6.4.
2 Whilst in idle mode, an MS shall continue to monitor all BCCH carriers as indicated by the BCCH allocation. 3GPP TS 05.08, subclause 6.6.1.
3 Mobile stations shall treat all ARF... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.5.3 Test purpose | 1. To verify that the MS correctly calculates the C2 criterion when the parameters affecting cell reselection are transmitted in the system information type 7 and 8 messages.
2. To verify that E-GSM, DCS 1 800 and PCS 1 900 MS decode parameters transmitted in the system information type 2 bis message.
3. To verify that... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.5.4.1 Initial conditions | a) Parameters changed from the default values in table 20.1.
Parameter
Carrier 1
Carrier 2
Carrier 3 (note)
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
53 / -60
32 / -81
40 / -73
OFF
OFF
OFF
RXLEV_ACCESS_MIN (dBV emf() / dBm)
23 / -90
23 / -90
30 / -83
BS_AG_BLKS_RES
1
1
1
PT
0
0
CRO
16 dB
10 dB
T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.5.4.2 Test Procedure | a) The SS activates the channels. The MS is not paged on carrier 1.
b) The MS is switched on.
c) After 50 s, the SS increases the level of carrier 2 to 42 dBVemf( ).
d) For an E-GSM MS only, when the SS receives a response on carrier 2, the SS stops paging on that carrier and after 30 s, the SS increases the level of ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.5.5 Test Requirements | 1) After step b), there shall be no response from the MS on carrier 2. For an E-GSM MS there shall also be no response on carrier 3.
2) After increasing the level of carrier 2 in step c), the MS shall respond on carrier 2 within 20 s.
3) After increasing the level of carrier 3 in step d), an E-GSM mobile shall respond ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.6 Cell reselection timings | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.6.1 Definition | void |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.6.2 Conformance requirement | 1. At least every 5 s the MS shall calculate the value of C1 and C2 for the serving cell and recalculate C1 and C2 values for non serving cells (if necessary). The MS shall then check whether:
1.1 ii) The calculated value of C2 for a non‑serving suitable cell exceeds the value of C2 for the serving cell for a period of... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.6.3 Test purpose | 1. To verify that:
1.1 The MS does not perform a cell reselection when the C2 value for a non serving cell does not exceed the C2 value of the serving cell for a period of at least 5 s.
1.2 When the MS performs an immediate cell reselection due to an unsuccessful random access attempt, the cell that the MS was camped o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.6.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.6.4.1 Initial conditions | Parameters changed from the default values in table 20.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier
RF Signal Level
(dBV emf() / dBm)
56 / -57
46 / -67
OFF
OFF
OFF
OFF
RXLEV_ACCESS_MIN (dBV emf() / dBm)
29 / -84
33 / -80
Max. Retrans
00
00
C1
27
13
C2
27
13
Below is an alternative table of p... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.6.4.2 Procedure | a) The SS activates the channels. The MS is not paged on any of the carriers.
b) The MS is switched on.
c) After 50 s, the SS starts paging continuously on carriers 1 and 2 for 20 s. The SS monitors carriers 1 and 2 for RA requests from the MS.
d) The SS stops paging on carriers 1 and 2 and waits for 20 s. (The MS shou... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.6.5 Test requirements | 1) In step c), the MS shall transmit 2 RA requests on carrier 1 followed by 2 RA requests on carrier 2. Subsequent RA requests on either carrier shall not occur within 4,5 s of the second RA request on that carrier.
2) In step f), there shall be no access on carrier 2 within 34 seconds of increasing the level of carrie... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.7 Priority of cells | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.7.1 Definition | In general, cell prioritization is a means of encouraging MSs to select some suitable cells in preference to others. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.7.2 Conformance requirement | 1. During cell selection a cell with low priority indication will only be selected if a suitable cell of normal priority cannot be found; 3GPP TS 03.22, subclause 3.5.2.1.
2.
Table 1a: Parameters affecting cell priority for cell selection
CELL_BAR_QUALIFY
CELL_BAR_ACCESS
Cell selection priority
Status for cell reselect... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.7.3 Test purpose | 1. To verify that the MS does not select a cell of low priority when a suitable cell of normal priority exists with a lower received signal strength.
2. To verify that the MS takes into account CELL_BAR_ACCESS and CELL BAR _QUALIFY when performing cell selection and reselection.
3. To verify that the MS meets conforman... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.7.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.7.4.1 Initial conditions | Parameters changed from Default values table 20.1
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
33 / -80
43 / -70
33 / -80
23 / -90
OFF
OFF
RXLEV_ACCESS_MIN
(dBV emf() / dBm)
3 / -110
23 / -90
13 / -100
13 / -100
CBA
0
1
1
0
CBQ
1
1
0
0
Access class 15
barred
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.7.4.2 Procedure | a) The SS activates the carriers and monitors for RA requests from the MS on carriers 1, 2, and 4.
b) The MS is switched on.
c) The MS is switched off. The SS deactivates the carriers.
d) The MS is placed in cell test operation mode.
NOTE: Cell test mode is a mode of operation defined in SIM administrative data field.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.7.5 Test requirements | 1) After step b), the first response from the MS shall be on carrier 4 within 33 s, followed by a response on carrier 1 before a response (if any) on carrier 2 within 50 s.
2) After step f), the first response from the MS shall be on carrier 3 within 33 s, followed by a response on carrier 1 before a response (if any) ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.8 Cell reselection when C1 (serving cell) < 0 for 5 s | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.8.1 Definition | void |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.8.2 Conformance requirement | 1. At least every 5 s the MS shall calculate the value of C1 and C2 for the serving cell and recalculate C1 and C2 values for non serving cells (if necessary). The MS shall then check whether:
i) The path loss criterion (C1) for current serving cell falls below zero for a period of 5 s. This indicates that the path los... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.8.3 Test purpose | 1. To verify that the MS meets conformance requirement 1.
2. To verify that the MS meets conformance requirement 2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.8.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.8.4.1 Initial conditions | Parameters changed from Default values table 20.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
63 / -50
33 / -80
OFF
OFF
OFF
OFF
RXLEV_ACCESS_MIN (dBV emf() / dBm)
43 / -70
23 / -90
CRO
30 dB
TO
0
PT
0
C1
20
10
C2
50
10
NOTE: With BS_PA_MFRMS = 5 (default va... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.8.4.2 Procedure | a) The SS activates the carriers. The MS is not paged on carrier 1. The SS monitors carriers 1 and 2 for RA requests from the MS.
b) The MS is switched on.
c) The SS reduces signal level on carrier 1 to -80 dBm / 33 dBV emf() for 4 s. Then, the SS raises the level back to -50 dBm / 63 dBV emf(). (C1 becomes -10 dB an... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.8.5 Test requirements | 1) After step b), there shall be no access on carrier 1 or carrier 2, within 50 s.
2) After step c), there shall be no access on carrier 2 within 30 s.
3) After step d), the MS shall access on carrier 2 within 20 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.9 Running average of the surrounding cell BCCH carrier signal levels | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.9.1 Definition | void |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.9.2 Conformance requirement | 1. Whilst in idle mode an MS shall continue to monitor all BCCH carriers as indicated by the BCCH allocation (BA - See table 1). A running average of received signal level (RLA_C) in the preceding 5 to:
- Max. {5, ((5 N + 6) DIV 7) * BS_PA_MFRMS / 4};
seconds shall be maintained for each carrier in the BCCH allocatio... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.