hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.10.1.2 Conformance requirement | 1. The block error rate (BLER) performance of data blocks containing PAN for PDTCH/MCS mentioned in the table 14.18.10.1-1 shall not exceed 10 % of input levels according to the table 14.18.10.1-1.
Table 14.18.10.1-1: Input signal level (for MS) at reference performance for GMSK, and 8-PSK with PAN included;
BTTI and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.10.1.3 Test purpose | 1. To verify that the MS does not exceed conformance requirement 1 for PDTCHs using different coding schemes and under static propagation conditions with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under static propagation conditions wit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.10.1.4 Method of test | Initial conditions
NOTE 1: The BA list sent on the BCCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf to35 dBVemf. Surrounding cell signal levels a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.10.1.5 Test requirements | The block error rate performance (BLER) as calculated by the SS for different MCSs under any combination of normal and extreme test voltages and ambient temperatures, shall not exceed the conformance requirement.
The PAN error rate as calculated by the SS under any combination of normal and extreme test voltages and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19 DARP Phase II Speech bearer tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1 TCH/FS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1.1 DTS-1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1.1.1 Definition | DARP Phase II, also referred as Mobile Station Receiver Diversity is a feature where the MS uses two receive antennas in order to improve performance under non-interfering and interfering scenarios.
The DARP Phase II reference test scenarios define a set of interfering signals and corresponding performance limits. The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1.1.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N. The reference performance shall be:
- For speech channels (TCH/FS, TCH/AFSx, TCH/AHSx) FER: 1 %
2. The values in table 2q are g... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1.1.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/FS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/FS under propagation condition TUhigh with an allowance f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/FS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits Standard Test Signal C1 on the traffic channel (wanted signal).
The SS commands the MS to create the traffic... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1.1.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. The interfering signal level is set to -70 dBm.
The fading c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.1.1.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Wrong decisi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2 TCH/AFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.1 DTS-1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.1.1 Definition | DARP Phase II, also referred as Mobile Station Receiver Diversity is a feature where the MS uses two receive antennas in order to improve performance under non-interfering and interfering scenarios.
The DARP Phase II reference test scenarios define a set of interfering signals and corresponding performance limits. The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.1.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N. The reference performance shall be:
- For speech channels (TCH/FS, TCH/AFSx, TCH/AHSx) FER: 1 %
2. The values in table 2q are g... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.1.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 12,2 kbit/s.
The SS transmits Standard Test Signal C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.1.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. The interfering signal level is set to -70 dBm.
The fading c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.1.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.2 DTS-2/5 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.2.1 Definition | DARP Phase II, also referred as Mobile Station Receiver Diversity is a feature where the MS uses two receive antennas in order to improve performance under non-interfering and interfering scenarios.
The DARP Phase II reference test scenarios define a set of interfering signals and corresponding performance limits. The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.2.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N. The reference performance shall be:
- For speech channels (TCH/FS, TCH/AFSx, TCH/AHSx) FER: 1 %
2. The values in table 2q are g... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.2.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 7,4 kbit/s.
The SS transmits Standard Test Signal C1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.2.4.2 Procedure | a) In addition to the wanted signal, the SS produces a further four interfering signals to produce scenario DTS-2.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, and signal level of -70 dBm.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.2.2.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3 TCH/AHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.1 DTS-1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.1.1 Definition | DARP Phase II, also referred as Mobile Station Receiver Diversity is a feature where the MS uses two receive antennas in order to improve performance under non-interfering and interfering scenarios.
The DARP Phase II reference test scenarios define a set of interfering signals and corresponding performance limits. The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.1.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N. The reference performance shall be:
- For speech channels (TCH/FS, TCH/AFSx, TCH/AHSx) FER: 1 %
2. The values in table 2q are g... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.1.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AHS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AHS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 7,4 kbit/s.
The SS transmits Standard Test Signal C1 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.1.4.2 Procedure | a) In addition to the wanted signal, the SS produces one further interfering signal to produce scenario DTS-1.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, and signal level of -70 dBm.
The fading characteristic of the wanted signal is TUHigh. Antenna correlation is 0 and antenn... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.1.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.2 DTS-2 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.2.1 Definition | DARP Phase II, also referred as Mobile Station Receiver Diversity is a feature where the MS uses two receive antennas in order to improve performance under non-interfering and interfering scenarios.
The DARP Phase II reference test scenarios define a set of interfering signals and corresponding performance limits. The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.2.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N. The reference performance shall be:
- For speech channels (TCH/FS, TCH/AFSx, TCH/AHSx) FER: 1 %
2. The values in table 2q are g... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.2.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AHS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AHS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 7,4 kbit/s.
The SS transmits Standard Test Signal C1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.2.4.2 Procedure | a) In addition to the wanted signal, the SS produces a further four interfering signals to produce scenario DTS-2.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, and signal level of -70 dBm.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.19.3.2.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20 VAMOS speech bearer tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.1 TCH HS – VDTS-1,VDTS-2/3 and VDTS-4 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.1.1 Definition | The VAMOS reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the VAMOS receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.1.2 Conformance requirement | - For AQPSK modulated speech channels ( TCH/HS, TCH/AFSx, TCH/AHSx, TCH/EFS, TCH/WFSx – in downlink), and their associated control channels, the applicable requirements are in tables 2aa for VAMOS I MS, 2ab for VAMOS II MS and 2ag for VAMOS III MS.
3GPP TS 45.005, subclause 6.3.2.1
- For AQPSK modulated speech channels... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.1.3 Test purpose | To verify that the MS does not exceed the conformance requirements for TCH/H under propagation condition TUhigh with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/H with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using tr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.1.4.3 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.2 TCH EFS – VDTS-1, VDTS-2/3 and VDTS-4 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.2.1 Definition | The reference sensitivity is the signal level at the MS receiver input at which a certain BER and FER must be achieved. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.2.2 Conformance requirement | - For AQPSK modulated speech channels ( TCH/HS, TCH/AFSx, TCH/AHSx, TCH/EFS, TCH/WFSx – in downlink), and their associated control channels, the applicable requirements are in tables 2aa for VAMOS I MS, 2ab for VAMOS II MS and 2ag for VAMOS III MS.
3GPP TS 45.005, subclause 6.3.2.1
- For AQPSK modulated speech channel... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.2.3 Test purpose | To verify that the MS does not exceed the conformance requirements for TCH/EFS under propagation condition TUhigh with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/H with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using tr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.2.4.2 Procedure | a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) In addition to the wanted signal, the SS produces a further interferer signal to produce scenario VDTS-1 according to TS 45.005 Q.1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.2.4.3 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.3.1 Definition | The VAMOS reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the VAMOS receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.3.2 Conformance requirement | - For AQPSK modulated speech channels ( TCH/HS, TCH/AFSx, TCH/AHSx, TCH/EFS, TCH/WFSx – in downlink), and their associated control channels, the applicable requirements are in tables 2aa for VAMOS I MS, 2ab for VAMOS II MS and 2ag for VAMOS III MS.
3GPP TS 45.005, subclause 6.3.2.1
- For AQPSK modulated speech channels... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.3.3 Test purpose | To verify that the MS does not exceed the conformance requirements for TCH/AFS under propagation condition TUhigh, no hopping with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.3.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 12.20 kbit/s.
The SS transmits a Standard Test Si... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.3.4.2 Procedure | a) The fading function is set to TUhigh, no Hopping for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) In addition to the wanted signal, the SS produces a further interferer signal to produce scenario VDTS-1 according to T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.3.4.3 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.4 TCH AHS – VDTS-1,VDTS-2/3 and VDTS-4 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.4.1 Definition | The VAMOS reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the VAMOS receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.4.2 Conformance requirement | - For AQPSK modulated speech channels ( TCH/HS, TCH/AFSx, TCH/AHSx, TCH/EFS, TCH/WFSx – in downlink), and their associated control channels, the applicable requirements are in tables 2aa for VAMOS I MS, 2ab for VAMOS II MS and 2ag for VAMOS III MS.
3GPP TS 45.005, subclause 6.3.2.1
- For AQPSK modulated speech channels... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.4.3 Test purpose | To verify that the MS does not exceed the conformance requirements for TCH/AHS under propagation condition TUhigh with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.4.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 4.75 kbit/s.
The SS transmits a Standard Test Sig... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.4.4.2 Procedure | a) The fading function is set to TUhigh for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) In addition to the wanted signal, the SS produces a further interferer signal to produce scenario VDTS-1 according to TS 45.005 Q.1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.4.4.3 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.5 TCH WFS – VDTS-1, VDTS-2/3 and VDTS-4 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.5.1 Definition | The VAMOS reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the VAMOS receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.5.2 Conformance requirement | - For AQPSK modulated speech channels ( TCH/HS, TCH/AFSx, TCH/AHSx, TCH/EFS, TCH/WFSx – in downlink), and their associated control channels, the applicable requirements are in tables 2aa for VAMOS I MS, 2ab for VAMOS II MS and 2ag for VAMOS III MS.
3GPP TS 45.005, subclause 6.3.2.1
• For AQPSK modulated speech channel... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.5.3 Test purpose | To verify that the MS does not exceed the conformance requirements for TCH/WFS under propagation condition TUhigh noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.5.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/WFS with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 6.60 kbit/s
The SS transmits a Standard Test Sig... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.5.4.2 Procedure | a) The fading function is set to TUhigh noFH for MS indicating VAMOS I or VAMOS II support and TUhigh/(Corr.=0, AGI=0 dB as per 3GPP TS 45.005 Annex Q.7) for MS indicating VAMOS III support.
b) The SS sets SCPIR_DL to +4 dB.
c) In addition to the wanted signal, the SS produces a further interferer signal to produce sce... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.5.4.3 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.6 FACCH/F – VDTS-1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.6.1 Definition | The VAMOS reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the VAMOS receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.6.2 Conformance requirement | - For AQPSK modulated speech channels ( TCH/HS, TCH/AFSx, TCH/AHSx, TCH/EFS, TCH/WFSx – in downlink), and their associated control channels, the applicable requirements are in tables 2aa for VAMOS I MS, 2ab for VAMOS II MS and 2ag for VAMOS III MS.
3GPP TS 45.005, subclause 6.3.2.1
- For AQPSK modulated speech channels... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.6.3 Test purpose | To verify that the MS does not exceed the conformance requirements for FACCH/F under propagation condition TUhigh with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.6.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.6.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using tr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.6.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal). The modulation of I1 shall be AQPSK and the SCPIR_DL shall be set to 0 dB (scenario VDTS-1). Signal I1 is continuous and has no fixed relationship with the bit transitions of ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.6.4.3 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Before limit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.7.1 Definition | The VAMOS reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the VAMOS receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.7.2 Conformance requirement | - For AQPSK modulated speech channels ( TCH/HS, TCH/AFSx, TCH/AHSx, TCH/EFS, TCH/WFSx – in downlink), and their associated control channels, the applicable requirements are in tables 2aa for VAMOS I MS, 2ab for VAMOS II MS and 2ag for VAMOS III MS.
3GPP TS 45.005, subclause 6.3.2.1
- For AQPSK modulated speech channels... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.7.3 Test purpose | To verify that the MS does not exceed the conformance requirements for FACCH/H under propagation condition TUhigh with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.7.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.20.7.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/H with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits a Standard Test Signal C1 (AQPSK) (wanted signal) on the active VAMOS subchannel (subchannel 2) using tr... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.