hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.23.2.5 Test requirement | 1) In step c, check that MS is not retransmitting the SACCH messages on uplink.
2) After step d, Check that the MS repeats the last message.
3) In step e, check that MS is not retransmitting the SACCH messages on uplink.
Specific Message Contents
None. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.23.3 Repeated SACCH / Uplink Repeated SACCH with SAPI 3 frames | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.23.3.1 Conformance requirements | At the MS side, if an uplink SACCH block contains a SAPI 0 frame and is not already a repetition, and if the last correctly received SACCH Repetition Order was set to "Repeated SACCH required", then the MS shall repeat this SACCH block at the next SACCH block period. If a SAPI 3 frame was also scheduled to be sent at t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.23.3.2 Test purpose | To verify that the MS delays sending of a SAPI 3 frame by one SACCH period if a repeated SAPI 0 SACCH frame is to be repeated according to the SACCH Repetition Parameter in the downlink SACCH block. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.23.3.3 Method of test | Initial Conditions
System simulator:
1 cell, default parameters.
Mobile Station:
The MS shall be in "Idle, updated" state.
Specific PICS Statements
-
PIXIT Statements
- Description of the basic procedures to display a mobile originated short message.
- Maximum length (characters) of a mobile originated short message.
F... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.0 Default contents of messages | Default contents SYSTEM INFORMATION messages and default settings
For cell A and B
For GSM use 26.6.14. For DCS use 26.6.15, for PCS 1 900 use 26.6.18, for GSM 450 use 26.6.16, for GSM 480 use 26.6.17, for GSM 750 use 26.6.19, for GSM 850 use 26.6.20, for GSM 710 use 26.6.21 and for T-GSM 810 use 26.6.22.
Cell C
The c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.1 TMSI reallocation | The intention of the TMSI Reallocation procedure is to assign a new temporary identity for the MS. If the message is not understood by the MS, the network could not establish a link to the MS. As this is a common MM procedure, it can be initiated at any time. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.1.1 Conformance requirement | 1) A Mobile Station shall acknowledge a new TMSI when explicitly allocated during a location updating procedure or an incoming call.
2) The TMSI shall be updated on the SIM when the Mobile Station is correctly deactivated in accordance with the manufacturer's instructions.
3) A Mobile Station shall answer paging with t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.1.2 Test purpose | To verify that the MS is able to receive and acknowledge a new TMSI by means of an explicit TMSI reallocation procedure.
To verify that the MS has stored the TMSI in a non-volatile memory.
The implicit reallocation procedure is tested in subclause 26.7.4.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.1.3 Method of test | Initial conditions
System Simulator:
Two cells A and B, belonging to different location areas a and b, default parameters.
Mobile Station:
The MS has valid TMSI (= TMSI1), CKSN, Kc. It is "idle updated" on cell B.
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2 Authentication | The purpose of this procedure is to verify the user identity. A correct response is essential to guarantee the establishment of the connection. If not, the connection will drop.
For GSM Authentication Challenge (i.e. Authentication with a SIM as defined in Annex A4 or GSM AKA using a USIM as defined TS 33.102) the SS s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.1 Authentication accepted | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.1.1 Conformance requirement | 1) A Mobile Station shall correctly respond to an Authentication Request message by sending an Authentication Response message with the SRES information field set to the same value as the one produced by the authentication algorithm in the network.
2) A Mobile Station shall indicate in a Paging Response message the cip... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.1.2 Test purpose | 1) To check that a Mobile Station correctly responds to an Authentication Request message by sending an Authentication Response message with the SRES information field set to the same value as the one produced by the authentication algorithm in the network.
2) To check that a Mobile Station indicates in a Paging Respon... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.1.3 Method of test | Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS has valid TMSI, CKSN (CKSN1), Kc. It is "idle updated" on the cell.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has valid TMSI, CKSN and Kc. It is "idle updated" on the cell.
Test Procedure
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.2 Authentication rejected | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.2.1 Conformance requirement | 1) After reception of an Authentication Reject message the Mobile Station shall:
1.1 not perform normal location updating.
1.2 not perform periodic location updating.
1.3 not respond to paging with TMSI.
1.4 reject any request from CM entity for MM connection except for emergency call.
1.5 not perform IMSI detach if de... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.2.2 Test purpose | 1) To check that ,after reception of an Authentication Reject message, the Mobile Station:
1.1 does not perform normal location updating.
1.2 does not perform periodic location updating.
1.3 does not respond to paging with TMSI.
1.4 rejects any request from CM entity for MM connection except for emergency call.
1.5 doe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.2.3 Method of test | Initial conditions
System Simulator:
Two cells: A and B, belonging to different location areas a and b.
IMSI attach/detach is allowed in both cells.
The T3212 time-out value is 1/10 hour in both cells.
Mobile Station:
The MS has valid TMSI, CKSN (CKSN2) and Kc. It is "idle updated" on cell B.
Specific PICS statements:
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.3 Authentication accepted with USIM | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.3.1 Conformance requirement | The mobile station shall be ready to respond upon an AUTHENTICATION REQUEST message at any time whilst a RR connection exists. With exception of the cases described in subclause 4.3.2.5.1, it shall process the challenge information and send back an AUTHENTICATION RESPONSE message to the network.
This IE (AUTN) shall be... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.3.2 Test purpose | To check that a Mobile Station with an USIM inserted:
1) correctly responds to an Authentication Request message including an UMTS authentication challenge by sending an Authentication Response message with the RES information field set to the same value as the one produced by the UMTS authentication algorithm in the n... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.3.3 Method of test | Initial conditions
System Simulator:
1 cell, Rel-99 MSC .
Mobile Station:
Test USIM is plugged into the MS.
The MS has valid TMSI. It is "idle updated" on the cell.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has valid TMSI, CKSN and Kc. It is "idle updated" on the cell.
Test P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.4 Authentication not accepted by MS with USIM (MAC Failure) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.4.1 Conformance requirement | In a UMTS authentication challenge, the authentication procedure is extended to allow the MS to check the authenticity of the core network. Thus allowing, for instance, detection of false base station.
Following a UMTS authentication challenge, the MS may reject the core network, on the grounds of an incorrect AUTN par... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.4.2 Test purpose | To check that a Mobile Station with an USIM inserted:
1) correctly responds to an AUTHENTICATION REQUEST message, with a MAC code failure in the AUTN parameter, by sending an AUTHENTICATION FAILURE message with the reject cause 'MAC failure'.
2) identifies itself upon reception of an IDENTITY REQUEST message, by sendi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.4.3 Method of test | Initial conditions
System Simulator:
1 cell, Rel-99 MSC .
Mobile Station:
Test USIM is plugged into the MS.
The MS has valid TMSI. It is "idle updated" on the cell.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has valid TMSI, CKSN and Kc. It is "idle updated" on the cell.
Test P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.5 Authentication not accepted by MS with USIM (Synch Failure) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.5.1 Conformance requirement | In a UMTS authentication challenge, the authentication procedure is extended to allow the MS to check the authenticity of the core network. Thus allowing, for instance, detection of false base station.
Following a UMTS authentication challenge, the MS may reject the core network, on the grounds of an incorrect AUTN par... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.5.2 Test purpose | To check that a Mobile Station with an USIM inserted:
1) correctly responds to an AUTHENTICATION REQUEST message, with an SQN failure in the AUTN parameter, by sending an AUTHENTICATION FAILURE message with the reject cause 'Synch failure'.
2) sends the AUTHENTICATION RESPONSE message to the network if a second AUTHENT... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.2.5.3 Method of test | Initial conditions
System Simulator:
1 cell, Rel-99 MSC .
Mobile Station:
Test USIM is plugged into the MS.
The MS has valid TMSI. It is "idle updated" on the cell.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has valid TMSI, CKSN and Kc. It is "idle updated" on the cell.
Test P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3 Identification | The purpose of this procedure is to check that the MS gives its identity as requested by the network. If this procedure does not work, it will not be possible for the network to rely on the identity claimed by the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.1 General Identification | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.1.1 Conformance requirement | 1) When requested by the network the Mobile Station shall send its IMSI.
2) When requested by the network the Mobile Station shall send the TMSI which it was previously allocated.
3) When requested by the network the Mobile Station shall send its IMEI as stored in the Mobile Equipment.
4) When requested by the network ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.1.2 Test purpose | 1) To verify that the MS sends identity information as requested by the system in the following cases: IMSI and TMSI are requested in non-ciphered mode, IMEI is requested in ciphered mode.
2) To verify that the MS sends its IMEI, when requested to do so, in non-ciphered mode.
3) To verify that the MS sends its IMEISV, ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.1.3 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.1.3.1 Identification / test 1 | Initial conditions
System Simulator:
1 cell, default values.
Mobile Station:
The MS has a valid TMSI. It is "idle updated" on the cell.
Specific PICS statements:
-
PIXIT statements:
- IMEI of the MS
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated" on the cell.
Test Procedure
The SS requests ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.1.3.2 Identification / test 2 | Initial conditions
System Simulator:
1 cell, default values.
Mobile Station:
The MS has a valid TMSI. It is in "idle updated".
Specific PICS statements:
-
PIXIT statements:
- IMEI of the MS
- IMEISV of the MS
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test Procedure
The SS requests id... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.2 Handling of IMSI shorter than the maximum length | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.2.1 Conformance requirement | The MS shall be capable of handling an IMSI that is not of the maximum length.
Reference(s)
3GPP TS 04.08 / 3GPP TS 24.008 subclause 10.5.1.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.2.2 Test purpose | To check that the MS behaves correctly when activated with an IMSI of length less than the maximum length.
In this condition, the MS shall:
- perform location updating;
- answer to paging with IMSI;
- give the correct IMSI when asked by an IDENTITY REQUEST;
- attempt CM connection establishment when requested to;
- att... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.3.2.3 Method of test | Initial conditions
System Simulator:
1 cell, default values.
IMSI attach/detach bit set to "1".
Mobile Station:
The MS has no valid TMSI.
It is "idle updated".
The IMSI has the value 001011234.
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of MS
The MS has no valid... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4 Location updating | This procedure is used to register the MS in the network. If it is not performed correctly, no call can be established. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.1 Location updating / accepted | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.1.1 Conformance requirement | 1.
1.1 If the network accepts a location updating from the Mobile Station and reallocates a TMSI in the Location Updating Accept message the Mobile Station shall acknowledge the reception of the new TMSI.
1.2 The Mobile Station shall answer to paging with this TMSI and include it in a Paging Response message.
2 If the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.1.2 Test purpose | 1) To test the behaviour of the MS if the network accepts the location updating of the MS.
For the network response three different cases are identified:
1.1) TMSI is allocated;
1.2) Location updating accept contains neither TMSI nor IMSI;
1.3) Location updating accept contains IMSI.
2) To verify that the MS , that sup... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.1.3 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.1.3.1 Location Updating/accepted/test1 | Initial conditions:
System Simulator:
Two cells, A and B, belonging to different location areas with location area identification a and b of the same PLMN.
IMSI attach/detach is allowed in both cells.
The T3212 time-out value is 1/10 hour in both cells.
Mobile Station:
The MS has a valid TMSI (=TMSI1) and CKSN (=CKSN1)... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.1.3.2 Location Updating/accepted/test2 | Initial conditions:
System Simulator:
Two cells, A and B, belonging to different location areas with location area identification a and b of the same PLMN.
System information2ter is broadcasted on the two cells (Cell A with L2pseudolength=18, Cell B with L2pseudolength=0) .
IMSI attach/detach is allowed in both cells.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2 Location updating / rejected | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.1 Location updating / rejected / IMSI invalid | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.1.1 Conformance requirement | 1) If the network rejects a location updating from the Mobile Station with the cause "IMSI unknown in HLR", "Illegal MS" or "Illegal ME" the Mobile Station shall:
1.1 not perform normal location updating;
1.2 not perform periodic location updating;
1.3 not respond to paging with IMSI;
1.4 not respond to paging with TMS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.1.2 Test purpose | To test the behaviour of the MS if the network rejects the location updating of the MS with the cause "IMSI unknown in HLR", "illegal MS" or "Illegal ME". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.1.3 Method of test | Initial conditions
System Simulator:
Two cells: A and B, belonging to different location areas of the same PLMN.
IMSI attach/detach is allowed in both cells.
The T3212 time-out value is 1/10 hour in both cells.
Mobile Station:
The MS has valid TMSI, CKSN and Kc. It is "idle updated" on cell A.
Specific PICS statements:... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.2 Location updating / rejected / PLMN not allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.2.1 Conformance requirement | 1) If the network reject a location updating from the Mobile Station with the cause "PLMN not allowed" the Mobile Station shall:
1.1 not perform periodic updating;
1.2 not perform IMSI detach when switched off;
1.3 not perform IMSI attach when switched on in the same location area;
1.4 not perform normal location updat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.2.2 Test purpose | To test the behaviour of the MS if the network rejects the location updating of the MS with the cause "PLMN not allowed". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.2.3 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.2.3.1 Location updating / rejected / PLMN not allowed / test 1 | Initial conditions
System Simulator:
One cell: C, belonging to PLMN1.
Two cells: A and B, belonging to different location areas a and b and belonging to PLMN2. PLMN2 is different from HPLMN and from PLMN1.
IMSI attach/detach is allowed in cells A and B but not in cell C.
The T3212 time-out value is 1/10 hour in cells A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.2.3.2 Location updating / rejected / PLMN not allowed / test 2 | Initial conditions
System Simulator:
One cell C, belonging to PLMN1.
Two cells A and B, belonging to different location areas a and b and belonging to PLMN2. PLMN2 is different from HPLMN.
IMSI attach/detach is allowed in cells A and B but not in cell C.
The T3212 time-out value is 1/10 hour in cells A and B.
Mobile St... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.3 Location updating / rejected / location area not allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.3.1 Conformance requirement | 1) If the network rejects a location updating from the Mobile Station with the cause "Location Area not allowed" the Mobile Station shall:
1.1 not perform periodic updating;
1.2 not respond to paging with TMSI;
1.3 reject any request from CM entity for MM connection other than for emergency call;
1.4 not perform IMSI d... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.3.2 Test purpose | To test the behaviour of the MS if the network rejects the location updating of the MS with the cause "Location Area not allowed".
To test that the MS deletes the list of forbidden LAs after switch off (power off). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.3.3 Method of test | Initial conditions
System Simulator:
Two cells: A and B, belonging to different location areas a and b.
IMSI attach/detach is allowed in both cells.
The T3212 time-out value is 1/10 hour in both cells.
Mobile Station:
The MS has a valid TMSI. It is "idle updated" on cell A.
Specific PICS statements:
- On/Off switch (TS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.4 Location updating / rejected / roaming not allowed in this location area | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.4.1 Conformance requirement | 1) If the network rejects a location updating from the Mobile Station with the cause "Roaming not allowed in this area" the Mobile Station shall:
1.1 not perform periodic updating;
1.2 not respond to paging with TMSI;
1.3 reject any request from CM entity for MM connection other than for emergency call;
1.4 not perform... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.4.2 Test purposes | Test purpose 1
To test that on receipt of a rejection using the Roaming cause code, the MS ceases trying to update on that cell, that this situation continues for at least one periodic location interval period, and that the corresponding list is re-set by switching off the MS or removing its power source.
Test purpose... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.2.4.3 Method of test | Initial conditions
The initial conditions shall be met before each of the different procedures.
System Simulator:
For procedures 1, 2, 3 and 5: Two cells A and B, belonging to different location areas of the same PLMN with LAI a and b. The MCC of that PLMN is the same as that of the HPLMN. The MNC of that PLMN is diffe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3 Location updating / abnormal cases | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.1 Location updating / abnormal cases / random access fails | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.1.1 Conformance requirement | If during the RR connection establishment phase of a normal location updating procedure, channel requests are not answered by the network, the Mobile Station shall:
1. send (Max-Retrans+1) Channel Request messages;
2. not try to establish a connection during a period of T3213;
3. then perform a normal location updating... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.1.2 Test purpose | To verify that when during the RR connection establishment phase of a location updating procedure, channel requests are not answered by the network, after expiry of T3213 (= 4s in Phase 2) and when the cell reselection procedure is finished the complete procedure is repeated if still necessary. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.1.3 Method of test | Initial conditions
System Simulator:
Two cells: A and B of the same PLMN, belonging to different location areas with LAI a and b.
The RF power level of cell B is higher than the one of cell A.
IMSI attach/detach is not allowed in both cells.
The T3212 time-out value is set to infinite in both cells.
Mobile Station:
The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.2 Location updating / abnormal cases / attempt counter less or equal to 4, LAI different | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.2.1 Conformance requirement | 1) When a failure such as cases d), f) and g) of subclause 4.4.4.9 of 3GPP TS 04.08 / 3GPP TS 24.008 has occurred during a normal location updating procedure, if the attempt counter is smaller than 4 and after expiry of T3211, the Mobile Station shall resend its Location Updating Request message with the Mobile Identit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.2.2 Test purpose | To verify that the MS performs normal location updating procedures when its attempt counter is smaller than 4.
To check that the MS does not perform the IMSI detach procedure when "idle not updated".
To verify that when "idle not updated" the MS can perform an emergency call.
To verify that when "idle not updated" the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.2.3 Method of test | Initial conditions
System Simulator:
Two cells: A and B of the same PLMN, belonging to different location areas with LAI a and b.
ATT flag shall be set to IMSI attach/detach allowed.
Mobile Station:
The MS is "idle updated" on cell A. A valid CKSN value is stored in the SIM and is noted "initial CKSN". A TMSI is alloca... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.3 Location updating / abnormal cases / attempt counter equal to 4 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.3.1 Conformance requirement | 1) When four failures such as cases d) to g) of subclause 4.4.4.9 of 3GPP TS 04.08 / 3GPP TS 24.008 have occurred during a normal location updating procedure the Mobile Station shall:
1.1 perform location updating after T3212 expiry by sending a Location Updating Request message with the Mobile Identity IE set to its I... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.3.2 Test purpose | To verify that the MS performs normal location updating procedures after T3212 expiry, when its attempt counter has reached value 4 and that the MS reset its attempt counter after a timer T3212 expiry.
To verify that the MS still follows the MM IDLE ATTEMPTING TO UPDATE state requirements or optionally follows the MM ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.3.3 Method of test | Initial conditions
System Simulator:
Two cells: A and B, belonging to different location areas a and b.
IMSI attach/detach is allowed in both cells.
T3212 is set to 6 minutes.
Mobile Station:
The MS is "Idle updated" on cell B with a valid CKSN and a TMSI.
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
- S... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.4 Location updating / abnormal cases / attempt counter less or equal to 4, stored LAI equal to broadcast LAI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.4.1 Conformance requirement | 1) When a failure such as cases d), f) and g) of subclause 4.4.4.9 of 3GPP TS 04.08 / 3GPP TS 24.008 has occurred during a periodic location updating procedure (the broadcast LAI is equal to the stored LAI):
1.1 the Mobile Station shall be able to establish an MM connection i.e. send a Channel Request and then a CM Ser... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.4.2 Test purpose | To verify that in the case when the attempt counter is smaller than 4 and the broadcast LAI is equal to the stored LAI, the MS is in the MM IDLE state and NORMAL SERVICE substate. To verify that timer T3211 is stopped after a MM connection establishment.
To verify that the MS uses the T3211 timer. and that it enters th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.4.3 Method of test | Initial conditions
System Simulator:
One cell: B, belonging to location area b.
IMSI attach/detach is allowed.
T3212 is set to 6 minutes.
Mobile Station:
The MS is "Idle updated" on cell B with a valid CKSN and a TMSI.
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
- SIM removable without power down (TSPC_... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.5 Location updating / abnormal cases / Network reject with Extended Wait Timer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.5.1 Conformance requirement | An MS configured for NAS signalling low priority indicates this by including the Device properties IE in the appropriate NAS message and setting the low priority indicator to "MS is configured to NAS signalling low priority" except for the following cases in which the MS shall set the low priority indicator to "MS is n... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.5.2 Test purpose | 1) To verify that the LAP indicator can be set in the MS.
2) To verify that the Delay Tolerant indicator is sent by the MS.
3) To verify that the MS uses the back-off timer if the network reject a request with the implicit reject procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.3.5.3 Method of test | Initial conditions
System Simulator:
Two cells: A and B of the same PLMN, belonging to different location areas with LAI a and b.
Mobile Station:
The MS has a valid TMSI. It is "Idle updated" on cell A.
The MS is configured for “low access priority” and Extended Access Barring”.
Specific PICS statements:
-
PIXIT statem... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.4 Location updating / release / expiry of T3240 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.4.1 Conformance requirement | The mobile station receiving a LOCATION UPDATING REJECT message shall start T3240: it shall abort the RR connection at the expiry of timer T3240.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 4.4.4.8 and 11.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.4.2 Test purpose | To verify that the MS aborts the RR-connection at the expiry of timer T3240. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.4.3 Method of test | Initial conditions
System Simulator:
Two cells: A and B, belonging to different location areas a and b.
Mobile Station:
The MS has a valid TMSI. It is "idle updated" on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS is "idle updated" on cell B.
Test Procedure
A normal loca... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.5 Location updating / periodic | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.5.1 Location updating / periodic spread | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.5.1.1 Conformance requirement | 1) The Mobile Stations shall perform spreading of the time before performing a periodic location updating when the location updating timer value is reduced.
2) The Mobile Station shall reset timer T3212 when the Mobile Station is deactivated, and shall start with a value between zero and the broadcasted value when reac... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.5.1.2 Test purpose | 1) To check that when the location updating timer is reduced, the timer running in the MS is started with a value depending on the current timer value and the new broadcasted T3212 value.
2) To verify that when the MS is reactivated in the same cell (as the one in which it was deactivated), IMSI attach being forbidden,... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.5.1.3 Method of test | Initial conditions
System Simulator:
One cell, T3212 is set to 30 minutes.
IMSI attach is allowed in the cell.
Mobile Station:
The MS is deactivated. The stored MCC, MNC and LAC correspond to the broadcasted values. The stored update status is "updated".
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final st... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.5.2 Location updating / periodic normal / test 1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.7.4.5.2.1 Conformance requirement | 1 The Mobile Station shall stop and reset the timer T3212 of the periodic location updating procedure when the first MM message is received or ciphering mode setting is completed in the case of MM connection establishment.
2 The Mobile Station shall stop and reset the timer T3212 of the periodic location updating proce... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.