hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44 Test case requirements for GPRS mobility management | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.1 Default conditions and default messages | Note that only the layer 3 messages are described in the document. The mapping of the layer 3 messages to lower layers and the use of logical channels is not described in the present document.
The default conditions and default message contents not specified in this clause must be set as in "GPRS default conditions".
B... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2 Elementary procedures of GPRS mobility management | The tests are based on 3GPP TS 04.08 / 3GPP TS 24.008. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1 GPRS attach procedure | This procedure is used to indicate for the network that the IMSI is available for traffic by establishment of a GMM context. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1 Normal GPRS attach | The normal GPRS attach procedure is a GMM procedure used by GPRS MSs of MS operation mode B or C to IMSI attach for GPRS services only. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.1 GPRS attach / accepted | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.1.1 Conformance requirement | 1) If the network accepts the GPRS attach procedure (signalled by an IMSI) and allocates a P-TMSI, the MS shall acknowledge the P-TMSI and continue communication with the P-TMSI.
2) If the network accepts the GPRS attach procedure (signalled by P-TMSI) and reallocates a new P-TMSI, the MS shall acknowledge the new P-TM... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.1.2 Test purpose | To test the behaviour of the MS if the network accepts the GPRS attach procedure.
The following cases are identified:
1) P-TMSI / P-TMSI signature is allocated;
2) P-TMSI / P-TMSI signature is reallocated;
3) Old P-TMSI / P-TMSI signature is not changed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.1.3 Method of test | Initial conditions
System Simulator:
One cell operating in network operation mode II.
Mobile Station:
The MS has a valid IMSI. MS is Idle Updated.
Specific PICS statements:
- MS operation mode B (TSPC_operation_mode_B).
- MS operation mode C (TSPC_operation_mode_C).
- Switch off on button (TSPC_Feat_OnOff).
- Automati... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.2 GPRS attach / rejected / IMSI invalid / illegal MS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.2.1 Conformance requirements | 1) If the network rejects a GPRS attach procedure from the Mobile Station with the cause 'Illegal MS', the Mobile Station shall consider SIM invalid for GPRS services until power is switched off or SIM is removed.
2) If the network rejects a GPRS attach procedure from the Mobile Station with the cause 'Illegal MS' the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.2.2 Test purpose | To test the behaviour of the MS if the network rejects the GPRS attach procedure of the MS with the cause 'illegal MS'. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.2.3 Method of test | Initial conditions
System Simulator:
Three cells (not simultaneously activated), cell A with MCC1/MNC1/LAC1/RAC1, cell B in MCC1/MNC1/LAC2/RAC1, cell C in MCC2/MNC1/LAC1/RAC1.
All three cells are operating in network operation mode II.
Mobile Station:
The MS has a valid P-TMSI-1 and RAI-1. MS is Idle Updated on cell A.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.3 GPRS attach / rejected / IMSI invalid / GPRS services not allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.3.1 Conformance requirement | 1) If the network rejects a GPRS attach procedure from the Mobile Station with the cause 'GPRS services not allowed', the Mobile Station shall consider SIM invalid for GPRS services until power is switched off or SIM is removed.
2) If the network rejects a GPRS attach procedure from the Mobile Station with the cause 'G... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.3.2 Test purpose | To test the behaviour of the MS if the network rejects the GPRS attach procedure of the MS with the cause 'GPRS services not allowed' (no valid GPRS-subscription for the IMSI). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.3.3 Method of test | Initial conditions
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 (HPLMN) and cell B in MCC2/MNC1/LAC1/RAC1.
Both cells are operating in network operation mode II.
Mobile Station:
The MS has a valid P-TMSI-1 and RAI-1. MS is Idle Updated on cell A.
Specific PICS statements:
- ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.4 GPRS attach / rejected / PLMN not allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.4.1 Conformance requirement | 1) If the network rejects a GPRS attach procedure from the Mobile Station with the cause 'PLMN not allowed' the Mobile Station shall:
1.1 not perform GPRS attach when switched on in the same routing area or location area;
1.2 not perform GPRS attach when in the same PLMN and when that PLMN is not selected manually;
1.3... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.4.2 Test purpose | To test the behaviour of the MS if the network rejects the GPRS attach procedure of the MS with the cause 'PLMN not allowed'. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.4.3 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.4.3.1 Test procedure 1 | Initial conditions
System Simulator:
Four cells (not simultaneously activated), cell A in MCC1/MNC2/LAC1/RAC1, cell B in MCC1/MNC2/LAC1/RAC1, cell C in MCC1/MNC2/LAC2/RAC1 and cell D in MCC2/MNC1/LAC1/RAC1.
- All four cells are operating in network operation mode II. The PLMN of the four cells should NOT be that of the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.4.3.2 Test procedure 2 | Initial conditions
System Simulator:
One cell operating in network operation mode II: MCC2/MNC1/LAC1/RAC1. The PLMN of the cell should NOT be that of the Mobile Station Home PLMN.
Mobile Station:
The MS has a valid P-TMSI-1 and RAI-2. MS is Idle Updated on cell A.
Specific PICS statements:
- MS operation mode C (TSPC_o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.5 GPRS attach / rejected / roaming not allowed in this location area | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.5.1 Conformance requirement | 1) If the network rejects a GPRS attach procedure from the Mobile Station with the cause 'roaming not allowed in this location area' the Mobile Station shall:
1.1 not perform GPRS attach when in the same location area;
1.2 delete the stored RAI, GPRS-CKSN, P-TMSI and P-TMSI signature;
1.3 store the LA in the 'forbidden... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.5.2 Test purpose | Test purpose 1
To test that on receipt of a rejection using the 'roaming not allowed in this location area' cause code, the MS ceases trying to attach on that location area. Successful GPRS attach procedure is possible in other location areas.
Test purpose 2
To test that if the MS is switched off or the SIM is removed ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.5.3 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.5.3.1 Test procedure 1 | Initial conditions
System Simulator:
Three cells (not simultaneously activated), cell A in MCC2/MNC1/LAC1/RAC1 (Not HPLMN), cell B in MCC2/MNC1/LAC2/RAC1 (Not HPLMN) and cell C in MCC2/MNC1/LAC1/RAC2 (Not HPLMN).
All three cells are operating in network operation mode II.
Mobile Station:
The MS has a valid P-TMSI-1 and... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.5.3.2 Test procedure 2 | Initial conditions
System Simulator:
One cell in MCC2/MNC1/LAC1/RAC1 (Not HPLMN) operating in network operation mode II.
Mobile Station:
The MS has a valid P-TMSI-1 and RAI-2. MS is Idle Updated.
Specific PICS statements:
- MS operation mode C (TSPC_operation_mode_C).
- MS operation mode B (TSPC_operation_mode_B) (only... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.5.3.3 Test procedure 3 | Initial conditions
System Simulator:
Six cells (not simultaneously activated), cell A in MCC2/MNC1/LAC1/RAC1 (Not HPLMN), cell B in MCC2/MNC1/LAC2/RAC1 (Not HPLMN), cell C in MCC2/MNC1/LAC3/RAC1 (Not HPLMN), cell D in MCC2/MNC1/LAC4/RAC1 (Not HPLMN), cell E in MCC2/MNC1/LAC5/RAC1 (Not HPLMN), cell F in MCC2/MNC1/LAC6/R... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.5.3.4 Test procedure 4 | Initial conditions
System Simulator:
Two cells, cell A in MCC2/MNC1/LAC1/RAC1 (not HPLMN) and cell B in MCC1/MNC1/LAC1/RAC1 (HPLMN).
Both cells are operating in network operation mode II.
Mobile Station:
The MS has a valid P-TMSI-1 and RAI-2. MS is Idle Updated on cell A.
Specific PICS statements:
- MS operation mode C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.6 GPRS attach / abnormal cases / access barred due to access class control | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.6.1 Conformance requirement | 1) The MS shall not perform GPRS attach procedure, but stays in the current serving cell and applies normal cell reselection process.
2) The Mobile Station shall perform the GPRS attach procedure when:
2.1 Access is granted.
2.2 Cell is changed.
Reference(s):
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.7.3.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.6.2 Test purpose | Test purpose 1
To test the behaviour of the MS in case of access class control (access is granted).
Test purpose 2
To test the behaviour of the MS in case of access class control (cell is changed). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.6.3 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.6.3.1 Test procedure 1 | Initial conditions
An access class x (0-15) is arbitrarily chosen. The SIM is programmed with this access class x. Communication with mobile stations using access class x is initially indicated to be barred.
System Simulator:
One cell operating in network operation mode II.
Access class x barred.
Mobile Station:
The MS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.6.3.2 Test procedure 2 | Initial conditions
An access class x (0-15) is arbitrarily chosen. The SIM is programmed with this access class x. Communication with mobile stations using access class x is indicated to be barred on cell A.
System Simulator:
Two cells, cell A in MCC1/MNC1/LAC1/RAC1 has access class x barred, cell B in MCC1/MNC1/LAC1/R... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.7 GPRS attach / abnormal cases / change of cell into new routing area | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.7.1 Conformance requirement | When a change of cell into a new routing area is performed before ATTACH ACCEPT message is received by the MS, the MS shall abort the GPRS attach procedure and re-initiate it immediately.
Reference(s):
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.7.3.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.7.2 Test purpose | To test the behaviour of the MS in case of procedure collision. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.7.3 Method of test | Initial conditions
System Simulator:
Two cells, cell A in MCC1/MNC1/LAC1/RAC1 and cell B in MCC1/MNC1/LAC1/RAC2.
Both cells are operating in network operation mode II.
Mobile Station:
The MS has a valid P-TMSI-1 and RAI-1. MS is Idle Updated on cell A.
Specific PICS statements:
- MS operation mode C (TSPC_operation_mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.8 GPRS attach / abnormal cases / power off | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.8.1 Conformance requirement | When power is switched off before ATTACH ACCEPT message is received by the MS, the MS shall abort the GPRS attach procedure and perform a GPRS detach procedure.
Reference(s):
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.7.3.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.8.2 Test purpose | To test the behaviour of the MS in case of procedure collision. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.8.3 Method of test | Initial conditions
System Simulator:
One cell operating in network operation mode II.
Mobile Station:
The MS has a valid P-TMSI-1 and RAI-1. MS is Idle Updated.
Specific PICS statements:
- MS operation mode C (TSPC_operation_mode_C).
- MS operation mode B (TSPC_operation_mode_B).
- Switch off on button (TSPC_Feat_OnOf... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.9 GPRS attach / abnormal cases / GPRS detach procedure collision | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.9.1 Conformance requirement | 1) When a DETACH REQUEST message is received by the MS (Detach type 're-attach not required') while waiting for an ATTACH ACCEPT message, the MS shall terminate the GPRS attach procedure and continue with the GPRS detach procedure.
2) When a DETACH REQUEST message is received by the MS (Detach type 're-attach required'... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.9.2 Test purpose | To test the behaviour of the MS in case of procedure collision. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.9.3 Method of test | Initial conditions
System Simulator:
One cell operating in network operation mode II.
Mobile Station:
The MS has a valid P-TMSI-1 and RAI-1. MS is Idle Updated.
Specific PICS statements:
- MS operation mode C (TSPC_operation_mode_C).
- MS operation mode B (TSPC_operation_mode_B) (only if mode C not supported).
- Switch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.10 GPRS attach / rejected / GPRS services not allowed in this PLMN | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.10.1 Conformance requirement | If the network rejects a GPRS attach procedure from the Mobile Station with the cause ' GPRS services not allowed in this PLMN’:
1. The MS shall delete any RAI, P-TMSI, P-TMSI signature, and GPRS ciphering key sequence number stored, shall set the GPRS update status to GU3 ROAMING NOT ALLOWED (and shall store it accord... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.10.2 Test purpose | To test the behaviour of the MS if the network rejects the GPRS attach procedure of the MS with the cause 'GPRS services not allowed in this PLMN'. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.10.3 Method of test | Initial conditions
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC2/LAC1/RAC1, cell B in MCC2/MNC1/LAC1/RAC1.
All two cells are operating in network operation mode II.. The PLMN of the two cells should NOT be that of the Mobile Station Home PLMN.
Mobile Station:
The MS has a valid TMSI-1,... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.11 GPRS attach / access barred due to EAB | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.11.1 Conformance requirement | For a mobile originated access attempt, a mobile station configured for EAB shall perform a preliminary access barring check (see sub-clause 3.3.1.4). If the preliminary access barring check indicates network access is barred then access to the network is not allowed. Otherwise, the mobile station shall proceed accordi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.11.2 Test purpose | To verify that Extended Access class Barring can be activated in the MS.
To verify that the MS does not perform location updating, GPRS attach or routing area updating if the network broadcast EAB and EAB is enabled in the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.11.3 Method of test | Initial conditions
System Simulator:
Two cells, cell A in MCC1/MNC1/LAC1/RAC1, cell B in MCC1/MNC1/LAC1/RAC2.
Both cells are operating in network operation mode II.
The SYSTEM INFORMATION TYPE 3 message indicates that the SYSTEM INFORMATION TYPE 21 is sent on the BCCH by setting the SYSTEM INFORMATION 21 Indicator in t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.12 GPRS attach / eDRX | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.12.1 Conformance requirement | 1) If the MS supports eDRX and requests the use of eDRX, the MS shall include the extended DRX parameters IE in the ATTACH REQUEST message.
2) The MS shall use extended idle mode DRX cycle only if the network has provided the extended DRX parameters IE during the last attach procedure.
Reference(s):
3GPP TS 24.008 subc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.12.2 Test purpose | To verify that a MS that supports eDRX and requests the use of eDRX will include the extended DRX parameters IE in the ATTACH REQUEST message.
To verify that a MS that supports eDRX and requests the use of eDRX will use extended idle mode DRX cycle only if the network has provided the extended DRX parameters IE during ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.1.12.3 Method of test | Initial conditions
System Simulator:
- One cell operating in network operation mode II.
- The cell supports eDRX.
Mobile Station:
- The MS has a valid IMSI. MS is Idle Updated.
- The MS is configured to use eDRX.
- The MS is configured to use a specific value of extended DRX cycle.
Specific PICS statements:
- MS operat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2 Combined GPRS attach | The combined GPRS attach procedure is a GMM procedure used by GPRS MSs of MS operation mode A or B to IMSI attach for GPRS or non-GPRS services. In order to use the combined GPRS attach procedure, the network must be in network operation mode I. All Combined GPRS test case are only applicable when the MS operates in Cl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.1 Combined GPRS attach / GPRS and non-GPRS attach accepted | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.1.1 Conformance requirement | 1) If the network accepts the combined GPRS attach procedure (signalled by an IMSI) and allocates a P-TMSI, the MS shall acknowledge the P-TMSI and continue communication with the P-TMSI.
2) If the network accepts the combined GPRS attach procedure (signalled by P-TMSI) and reallocates a new P-TMSI, the MS shall acknow... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.1.2 Test purpose | To test the behaviour of the MS if the network accepts the GPRS attach procedure.
The following cases are identified:
1) P-TMSI / P-TMSI signature is allocated;
2) P-TMSI / P-TMSI signature is reallocated;
3) Old P-TMSI / P-TMSI signature is not changed;
4) Mobile terminating CS call is allowed with IMSI;
5) Mobile ter... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.1.3 Method of test | Initial conditions
System Simulator:
One cell operating in network operation mode I.
Mobile Station:
The MS has a valid IMSI. MS is Idle Updated.
Specific PICS statements:
- MS operation mode B (TSPC_operation_mode_B)
- MS operation mode A (TSPC_operation_mode_A).
- Switch off on button (TSPC_Feat_OnOff).
- Automatic G... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.2 Combined GPRS attach / GPRS only attach accepted | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.2.1 Conformance requirement | 1) If the network accepts the combined GPRS attach procedure, but GMM cause code 'IMSI unknown in HLR' is sent to the MS the Mobile Station shall delete the stored TMSI, LAI and CKSN. The Mobile Station shall consider SIM invalid for non-GPRS services until power is switched off or SIM is removed.
2) If the network acc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.2.2 Test Purpose | Test purpose 1
To test the behaviour of the MS if the network accepts the GPRS attach procedure with indication GPRS only, GMM cause 'IMSI unknown in HLR'.
Test purpose 2
To test the behaviour of the MS if the network accepts the GPRS attach procedure with indication GPRS only, GMM cause 'MSC temporarily not reachable'... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.2.3 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.2.3.1 Test Procedure 1 | Initial conditions
System Simulator:
One cell operating in network operation mode I.
Mobile Station:
The MS has a valid IMSI. MS is Idle Updated.
Specific PICS statements:
- MS operation mode B (TSPC_operation_mode_B)
- MS operation mode A (TSPC_operation_mode_A).
- Switch off on button (TSPC_Feat_OnOff).
- Automatic ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.2.3.2 Test Procedure 2 | Initial conditions
System Simulator:
One cell operating in network operation mode I. T3212 is set to 6 minutes.
Mobile Station:
The MS has a valid TMSI, P-TMSI and RAI. MS is Idle Updated.
Specific PICS statements:
- MS operation mode B (TSPC_operation_mode_B)
- MS operation mode A (TSPC_operation_mode_A).
- Automatic ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.3 Combined GPRS attach / GPRS attach while IMSI attach | 44.2.1.2.3.1 Void |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.3.2 Conformance requirement | If the GPRS MS is already attached for non-GPRS services by the MM specific attach procedure, but wants to perform an attach for GPRS services, the combined GPRS attach procedure is performed.
Reference(s):
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.7.3.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.3.3 Test Purpose | To test the behaviour of the MS if GPRS attach performed while IMSI attached. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.3.4 Method of test | Initial conditions
System Simulator:
One cell operating in network operation mode I. ATT flag is set.
Mobile Station:
The MS has a valid TMSI-1, P-TMSI-1 and RAI-1.
Specific PICS statements:
- MS operation mode B (TSPC_operation_mode_B)
- MS operation mode A (TSPC_operation_mode_A).
- Switch off on button (TSPC_Feat_O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.4 Combined GPRS attach / rejected / IMSI invalid / illegal ME | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.4.1 Conformance requirement | 1) If the network rejects a combined GPRS attach procedure from the Mobile Station with the cause 'Illegal ME', the Mobile Station shall consider SIM invalid for GPRS and non-GPRS services until power is switched off or SIM is removed.
2) If the network rejects a combined GPRS attach procedure from the Mobile Station w... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.4.2 Test purpose | To test the behaviour of the MS if the network rejects the combined GPRS attach procedure of the MS with the cause 'Illegal ME'. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.4.3 Method of test | Initial conditions
System Simulator:
Three cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1, cell B in MCC1/MNC1/LAC1/RAC2, cell C in MCC2/MNC1/LAC1/RAC1.
All three cells are operating in network operation mode I.
Mobile Station:
The MS has a valid TMSI-1, P-TMSI-1 and RAI-1. MS is Idle Updated on ce... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.5 Combined GPRS attach / rejected / GPRS services and non-GPRS services not allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.5.1 Conformance requirement | 1) If the network rejects a combined GPRS attach procedure from the Mobile Station with the cause 'GPRS services and non-GPRS services not allowed', the Mobile Station shall consider SIM invalid for GPRS and non-GPRS services until power is switched off or SIM is removed.
2) If the network rejects a combined GPRS attac... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.5.2 Test purpose | To test the behaviour of the MS if the network rejects the combined GPRS attach procedure of the MS with the cause 'GPRS services and non-GPRS services not allowed'. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.5.3 Method of test | Initial conditions
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 and cell B in MCC2/MNC1/LAC1/RAC1.
Both cells are operating in network operation mode I.
Mobile Station:
The MS has a valid TMSI, P-TMSI and RAI. MS is Idle Updated on cell A.
Specific PICS statements:
- MS oper... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.6 Combined GPRS attach / rejected / GPRS services not allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.6.1 Conformance requirement | 1) If the network rejects a combined GPRS attach procedure from the Mobile Station with the cause 'GPRS services not allowed', the Mobile Station shall consider SIM invalid for GPRS services until power is switched off or SIM is removed.
2) If the network rejects a combined GPRS attach procedure from the Mobile Station... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.6.2 Test purpose | To test the behaviour of the MS if the network rejects the GPRS attach procedure of the MS with the cause 'GPRS services not allowed'. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.6.3 Method of test | Initial conditions
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 and cell B in MCC2/MNC1/LAC1/RAC1.
Both cells are operating in network operation mode I.
ATT flag set to 1.
Mobile Station:
The MS has a valid TMSI, P-TMSI-1 and RAI-1. MS is Idle Updated on cell A.
Specific PIC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.7 Combined GPRS attach / rejected / location area not allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.7.1 Conformance requirement | 1) If the network rejects a combined GPRS attach procedure from the Mobile Station with the cause 'location area not allowed' the Mobile Station shall:
1.1 not perform combined GPRS attach when in the same location area;
1.2 delete the stored LAI, CKSN, TMSI, RAI, GPRS-CKSN, P-TMSI and P-TMSI signature;
1.3 store the L... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.7.2 Test purpose | To test the behaviour of the MS if the network rejects the combined GPRS attach procedure with the cause 'Location Area not allowed'.
To test that the MS deletes the list of forbidden LAs when power is switched off. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.7.3 Method of test | Initial conditions
System Simulator:
Three cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1, cell B in MCC1/MNC1/LAC1/RAC2, cell C in MCC1/MNC1/LAC2/RAC1.
All cells are operating in network operation mode I.
Mobile Station:
The MS has a valid TMSI, P-TMSI and RAI. MS is Idle Updated on cell A.
Specif... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.8 Combined GPRS attach / abnormal cases / attempt counter check / miscellaneous reject causes | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.8.1 Conformance requirement | 1) When a combined GPRS attach procedure is rejected with the attach attempt counter less than five, the Mobile Station shall repeat the combined GPRS attach procedure after T3311 timeout.
2) When a combined GPRS attach procedure is rejected with the attach attempt counter five, the Mobile Station shall delete the stor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.8.2 Test purpose | To test the behaviour of the MS with respect to the attach attempt counter. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.8.3 Method of test | Initial conditions
System Simulator:
One cell operating in network operation mode I. T3302 is set to 12 minutes.
Mobile Station:
The MS has a valid TMSI, P-TMSI and RAI. MS is Idle Updated.
Specific PICS statements:
- MS operation mode B (TSPC_operation_mode_B)
- MS operation mode A (TSPC_operation_mode_A).
- Automatic... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.9 Combined GPRS attach / abnormal cases / GPRS detach procedure collision | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.9.1 Conformance requirement | 1) When a DETACH REQUEST message is received by the MS (Detach type 're-attach not required') while waiting for an ATTACH ACCEPT message or ATTACH REJECT message, the MS shall terminate the combined GPRS attach procedure and continue with the combined GPRS detach procedure.
2) When a DETACH REQUEST message is received ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.9.2 Test purpose | To test the behaviour of the MS in case of procedure collision. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 44.2.1.2.9.3 Method of test | Initial conditions
System Simulator:
One cell operating in network operation mode I.
Mobile Station:
The MS has a valid TMSI, P-TMSI and RAI. MS is Idle Updated.
Specific PICS statements:
- MS operation mode B (TSPC_operation_mode_B)
- MS operation mode A (TSPC_operation_mode_A).
- Switch off on button (TSPC_Feat_OnOff... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.