hash stringlengths 32 32 | doc_id stringlengths 7 13 | section stringlengths 3 121 | content stringlengths 0 2.2M |
|---|---|---|---|
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 4.3.2 Blocking and spurious response - control channels | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 4.3.2.1 Definition and applicability | Blocking is a measure of the ability of the receiver to receive a modulated wanted input signal in the presence of an unwanted broadband input signal, on frequencies other than those of the spurious responses or the adjacent channels, without exceeding a given degradation. The requirements and this test apply to profes... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 4.3.2.2 Conformance requirement | 1) The blocking characteristics of the receiver are specified in ETSI TS 102 933-1 [3], clause 7.1.2. The reference sensitivity performance as specified in table 1 of ETSI TS 100 910 [2] shall be met when the following signals are simultaneously input to the receiver: - a useful signal at frequency f0, as specified in ... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 4.3.2.3 Test purpose | To verify that the broadband blocking performance is met without any exception of out of band spurious responses. NOTE: Not all of the possible out-of-band frequencies for broadband interferers are tested as this results in excessive test time and inapplicable test setup. However, an aggregation of broadband signals sp... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 4.3.2.4 Method of test | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 4.3.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure, except the BCCH frequency list shall be empty, on a TCH as specified in ETSI TS 102 933-1 [3], clause 7.1.2, table 11, ARFCN 970. The power control level is set to maximum power (PCL2) but may be relaxed to PCL10 to limit constraint on test setup. The SS ... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 4.3.2.4.2 Procedure | a) The SS produces a static wanted signal and a broadband interfering signal at the same time. There is no correlation in the modulation between the signals. The amplitude of the wanted signal is set to -101 dBm/200 kHz. b) The SS sends a Layer 3 message which does not require a Layer 3 response from the professional M... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5 Receiver characteristics for 2 Watt mobiles | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.0 General | In this clause receiver measurements are described for professional small mobile stations equipped with an integrated antenna, so called handheld stations. In order to test those mobile stations refer to the general conditions in ETSI EN 300 607-1 [i.2]. Wherever in this clause, for FACCH tests, the SS is required to s... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.1 Reference sensitivity | The reference sensitivity is the signal level at the professional small MS receiver input at which a certain BER and FER shall be achieved. The requirements and this test apply to professional small MS supporting speech. For tests using ARFCN ranges the table 8 shall be used. Table 8: ARFCN Ranges Term Band Low ARFCN r... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2 Blocking with CW interfering Signals | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.1 Blocking and spurious response - speech channels | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.1.1 Definition and applicability | Blocking is a measure of the ability of the receiver to receive a modulated wanted input signal in the presence of an unwanted input signal, on frequencies other than those of the spurious responses or the adjacent channels, without exceeding a given degradation. The requirements and this test apply to professional sma... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.1.2 Conformance requirement | 1) The blocking characteristics of the receiver are specified separately for in-band and out-of-band performance and shall be as identified in ETSI TS 102 933-1 [3], clause 8.1. The reference sensitivity performance as specified in table 1 of ETSI TS 100 910 [2] shall be met when the following signals are simultaneousl... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.1.3 Test purpose | 1) To verify that the in band blocking performance is met without exceeding the total number of allowed in band spurious responses. An allowance is made for the statistical significance of the test. 2) To verify that at selected out-of-band frequencies, the out-of-band blocking performance is met without exceeding the ... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.1.4 Method of test | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure, except the BCCH frequency list shall be empty, on a TCH with an arbitrary ARFCN in the range supported by the professional small MS. The power control level is set to maximum power. The SS transmits Standard Test Signal C1 on the traffic channel (TCH freq... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.1.4.2 Procedure | a) The SS produces a static wanted signal and a static interfering signal at the same time. The amplitude of the wanted signal is set to -100 dBm. b) The unwanted signal is a C.W. signal (Standard test signal IO) of frequency FB. It is applied in turn on the subset of frequencies calculated in step c) in the overall ra... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.1.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate values given in table 10. This shall apply under normal test voltage and ambient temperature, and with the interfering signal at any frequency in the range specified. Table 10: Limits for blocking Channel Type of measurement Test limit erro... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.2 Blocking and spurious response - control channels | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.2.1 Definition and applicability | Blocking is a measure of the ability of the receiver to receive a modulated wanted input signal in the presence of an unwanted input signal, on frequencies other than those of the spurious responses or the adjacent channels, without exceeding a given degradation. The requirements and this test apply to professional sma... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.2.2 Conformance requirement | 1) The blocking characteristics of the receiver are specified separately for in-band and out-of-band performance and shall be as identified in ETSI TS 102 933-1 [3], clause 8.1. The reference sensitivity performance as specified in table 1 of ETSI TS 100 910 [2] shall be met when the following signals are simultaneousl... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.2.3 Test purpose | 2) To verify that the in band blocking performance is met without exceeding the total number of allowed in band spurious responses. An allowance is made for the statistical significance of the test. 3) To verify that at selected out-of-band frequencies, the out-of-band blocking performance is met without exceeding the ... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.2.4 Method of test | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure, except the BCCH frequency list shall be empty, on a TCH with an arbitrary ARFCN in the range supported by the professional small MS. The power control level is set to maximum power. The SS transmits Standard Test Signal C1 on the traffic channel (TCH freq... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.2.4.2 Procedure | a) The SS sends a Layer 3 message which does not require a Layer 3 response from the professional small MS. Due to interfering signals, the professional small MS may not be able to acknowledge the Layer 2 frame. Frame erasures are indicated by repeated L2 frames. b) The SS is set to produce a TUhigh wanted signal and a... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.2.2.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate given in table 12. This shall apply under normal test voltage and ambient temperature, and with the interfering signal at any frequency in the range specified. ETSI ETSI TS 102 933-2 V2.1.1 (2015-06) 24 Table 12: Limits for blocking Channel... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3 Blocking with Broadband interfering Signals | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.1 Blocking and spurious response - speech channels | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.1.1 Definition and applicability | Blocking is a measure of the ability of the receiver to receive a modulated wanted input signal in the presence of an unwanted broadband input signal, on frequencies other than those of the spurious responses or the adjacent channels, without exceeding a given degradation. The requirements and this test apply to profes... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.1.2 Conformance requirement | 1) The blocking characteristics of the receiver are specified in ETSI TS 102 933-1 [3], clause 8.1.2. The reference sensitivity performance as specified in table 1 of ETSI TS 100 910 [2] shall be met when the following signals are simultaneously input to the receiver: - a useful signal at frequency f0, as specified in ... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.1.3 Test purpose | To verify that the broadband blocking performance is met without any exception of out of band spurious responses. NOTE: Not all of the possible out-of-band frequencies for broadband interferers are tested as this results in excessive test time and inapplicable test setup. However, an aggregation of broadband signals sp... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.1.4 Method of test | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure, except the BCCH frequency list shall be empty, on a TCH as specified in ETSI TS 102 933-1 [3], clause 8.1.2, table 14, ARFCN 970. The power control level is set to maximum power (PCL5) but may be relaxed to PCL10 to limit constraint on test setup. The SS ... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.1.4.2 Procedure | a) The SS produces a static wanted signal and a broadband interfering signal at the same time. There is no correlation in the modulation between the signals. The amplitude of the wanted signal is set to -101 dBm/200 kHz. b) The unwanted signal is an aggregation of two 5 MHz BW LTE signals (E-TM1.1) set respectively on ... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.1.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate values given in table 13. This shall apply under normal test voltage and ambient temperature, and with the interfering signal at the frequency specified. Table 13: Limits for blocking Channel Type of measurement Test limit error rate % Mini... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.2 Blocking and spurious response - control channels | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.2.1 Definition and applicability | Blocking is a measure of the ability of the receiver to receive a modulated wanted input signal in the presence of an unwanted broadband input signal, on frequencies other than those of the spurious responses or the adjacent channels, without exceeding a given degradation. The requirements and this test apply to profes... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.2.2 Conformance requirement | 1) The blocking characteristics of the receiver are specified in ETSI TS 102 933-1 [3], clause 8.12. The reference sensitivity performance as specified in table 1 of ETSI TS 100 910 [2] shall be met when the following signals are simultaneously input to the receiver: - a useful signal at frequency f0, as specified in E... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.2.3 Test purpose | To verify that the broadband blocking performance is met without any exception of out of band spurious responses. NOTE: Not all of the possible out-of-band frequencies for broadband interferers are tested as this results in excessive test time and inapplicable test setup. However, an aggregation of broadband signals sp... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.2.4 Method of test | |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure, except the BCCH frequency list shall be empty, on a TCH as specified in ETSI TS 102 933-1 [3], clause 8.1.2, table 14, ARFCN 970. The power control level is set to maximum power (PCL5) but may be relaxed to PCL10 to limit constraint on test setup. The SS ... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.2.4.2 Procedure | a) The SS produces a static wanted signal and a broadband interfering signal at the same time. There is no correlation in the modulation between the signals. The amplitude of the wanted signal is set to -101 dBm/200 kHz. b) The SS sends a Layer 3 message which does not require a Layer 3 response from the professional s... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 5.3.2.5 Test requirements | The error rate measured in this test shall not exceed the test limit error rate given in table 14. This shall apply under normal test voltage and ambient temperature, and with the interfering signal at the frequency specified. ETSI ETSI TS 102 933-2 V2.1.1 (2015-06) 27 Table 14: Limits for blocking Channel Type of meas... |
252768747589ce69c1e0e2dfd7e6abfc | 102 933-2 | 6 Other requirements | Test cases which are not explicitly described in the present document shall be taken from ETSI TS 100 607-1 [1]. ETSI ETSI TS 102 933-2 V2.1.1 (2015-06) 28 Annex A (informative): Bibliography • ETSI EN 300 919: "Digital cellular telecommunications system (Phase 2+) (GSM); Types of Mobile Stations (MS) (GSM 02.06)". • C... |
ca1026752394eea3af7b1a01e2c45dce | 102 917-1 | 1 Scope | The present document provides the Protocol Implementation Conformance Statement (PICS) proforma for the test specifications for the channel congestion control algorithms operating in the 5,9 GHz range as specified in TS 102 687 [1] and TS 102 724 [2] and in compliance with the relevant requirements and in accordance wi... |
ca1026752394eea3af7b1a01e2c45dce | 102 917-1 | 2 References | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which ar... |
ca1026752394eea3af7b1a01e2c45dce | 102 917-1 | 2.1 Normative references | The following referenced documents are necessary for the application of the present document. [1] ETSI TS 102 687: "Intelligent Transport Systems (ITS); Decentralized Congestion Control Mechanisms for Intelligent Transport Systems operating in the 5 GHz range; Access layer part". [2] ETSI TS 102 724: "Intelligent Trans... |
ca1026752394eea3af7b1a01e2c45dce | 102 917-1 | 2.2 Informative references | The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. Not applicable. ETSI ETSI TS 102 917-1 V1.1.1 (2013-01) 6 |
ca1026752394eea3af7b1a01e2c45dce | 102 917-1 | 3 Definitions and abbreviations | |
ca1026752394eea3af7b1a01e2c45dce | 102 917-1 | 3.1 Definitions | For the purposes of the present document, the terms and definitions given in TS 102 687 [1], TS 102 724 [2] and the following apply: PICS proforma: document, in the form of a questionnaire, designed by the protocol specifier or conformance test suite specifier, which, when completed for an OSI implementation or system,... |
ca1026752394eea3af7b1a01e2c45dce | 102 917-1 | 3.2 Abbreviations | For the purposes of the present document, the abbreviations given in TS 102 687 [1], TS 102 724 [2] and the following apply: CCH Control CHannel ICS Implementation Conformance Statement IUT Implementation Under Test PDU Protocol Data Unit PICS Protocol Implementation Conformance Statement |
ca1026752394eea3af7b1a01e2c45dce | 102 917-1 | 4 Conformance | A PICS proforma which conforms to this PICS proforma specification shall be technically equivalent to annex A, and shall preserve the numbering and ordering of the items in annex A. A PICS which conforms to this PICS proforma specification shall: a) describe an implementation which claims to conform to TS 102 687 [1] a... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 1 Scope | The present document defines the Radio Frequency requirements specific for the professional Mobile Station. The measurement methods are specified in ETSI TS 102 933-2 [5] and ETSI TS 100 607-1 [2]. Requirements are defined for two categories of parameters: • Those that are required to provide compatibility between the ... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 2 References | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 2.1 Normative references | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which ar... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 2.2 Informative references | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. NOTE: While any hyperlinks in... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 3 Abbreviations | For the purposes of the present document, the abbreviations given in ETSI TR 101 748 [i.1] and the following apply: EDOR ETCS Data Only Radio ETCS European Train Control System OPH Operational Purpose Handheld OPS Operational Purpose Handheld for Shunting |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 4 Frequency bands and channel arrangement | a) Railways GSM 900 Band, R-GSM (includes Standard and Extended GSM 900 Band): - for Railways GSM 900 band, the system is required to operate in the following frequency band: 876 MHz to 915 MHz: mobile transmit, base receive; 921 MHz to 960 MHz: base transmit, mobile receive. b) Extended Railways GSM 900 Band, ER-G... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 5 Transmitter characteristics for 8 Watt mobiles | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 5.0 General provisions | Throughout this clause, unless otherwise stated, requirements are given in terms of power levels at the antenna connector of the equipment. For equipment with integral antenna only, a reference antenna with 0 dBi gain shall be assumed. For GMSK modulation, the term output power refers to the measure of the power when a... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 5.1 Output power | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 5.1.1 Mobile Station | The MS maximum output power and lowest power control level shall be, according to its class (as specified in ETSI EN 300 919 [1]), as defined in tables 1 and 2 . For GMSK modulation: Table 1 Power class ER-GSM/R-GSM Tolerance (dB) Nominal Maximum output for conditions Power Normal Extreme 2 8 W (39 dBm) ±2 ±2,5 For 8-P... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 6 Transmitter characteristics for 2 Watt mobiles | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 6.0 General provisions | Throughout this clause, unless otherwise stated, requirements are given in terms of power levels at the antenna connector of the equipment. For equipment with integral antenna only, a reference antenna with 0 dBi gain shall be assumed. For GMSK modulation, the term output power refers to the measure of the power when a... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 6.1 Output power | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 6.1.1 Mobile Station | The MS maximum output power and lowest power control level shall be, according to its class (as specified in ETSI EN 300 919 [1]), as defined in tables 5 and 6. For GMSK modulation: Table 5 Power class ER-GSM/R-GSM Tolerance (dB) Nominal Maximum output for conditions Power Normal Extreme 4 2 W (33 dBm) ±2 ±2,5 For 8-PS... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 7 Receiver characteristics for 8 Watt mobiles | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 7.0 General provisions | In this clause, the requirements are given in terms of power levels at the antenna connector of the receiver assuming a 0 dBi gain antenna. The following requirements are only applicable for ARFCN located within the R-GSM/ER-GSM band, i.e.: 955 to 973 for R-GSM MS and 940 to 973 for ER-GSM MS. NOTE: Non static wanted s... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 7.1 Blocking characteristics | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 7.1.0 Blocking characteristics of the receiver | The blocking characteristics of the receiver are specified separately for in-band and out-of-band performance as identified in tables 9 and 10. Table 9 Frequency band Frequency range (MHz) ER-GSM/R-GSM professional MS in-band 915 to 925,6 out-of-band (a) 0,1 to < 915 out-of-band (b) 925,6 to < 927 out-of-band (c) 927 t... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 7.1.1 Blocking with CW interfering signals | The reference sensitivity performance as specified in ETSI TS 100 910 [4], tables 1, 1a, 1b, 1c, 1d and 1e shall be met when the following signals are simultaneously input to the receiver: • for all cases a useful signal, modulated with the relevant supported modulation (GMSK or 8-PSK), at frequency f0, at a level of -... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 7.1.2 Blocking with broadband interfering signals | The receiver performance as specified in ETSI TS 100 910 [4], tables 1, 1a, 1b, 1c, 1d and 1e shall be maintained in presence of the following interferers at the receiver antenna port. Table 11 Wanted GSMR Signal Level on ARFCN 970 (dBm) Interferer(s) Characteristics Comment Mobile Input Level (dBm/200 kHz) ARFCN Freq.... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 8 Receiver characteristics for 2 Watt mobiles | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 8.0 General provisions | In this clause, the requirements are given in terms of power levels at the antenna connector of the receiver assuming a 0 dBi gain antenna. The following requirements are only applicable for ARFCN located within the R-GSM/ER-GSM band, i.e.: 955 to 973 for R-GSM MS and 940 to 973 for ER-GSM MS. NOTE: Non static wanted s... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 8.1 Blocking characteristics | |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 8.1.0 Blocking characteristics of the receiver | The blocking characteristics of the receiver are specified separately for in-band and out-of-band performance as identified in tables 12 and 13. Table 12 Frequency band Frequency range (MHz) ER-GSM/R-GSM professional MS in-band 915 to 925,6 out-of-band (a) 0,1 to < 915 out-of-band (b) 925,6 to < 927 out-of-band (c) 927... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 8.1.1 Blocking with CW interfering signals | The reference sensitivity performance as specified in ETSI TS 100 910 [4], tables 1, 1a, 1b, 1c, 1d and 1e shall be met when the following signals are simultaneously input to the receiver: • for all cases a useful signal, modulated with the relevant supported modulation (GMSK or 8-PSK), at frequency f0, at a level of -... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 8.1.2 Blocking with broadband interfering signals | The receiver performance as specified in ETSI TS 100 910 [4], tables 1, 1a, 1b, 1c, 1d and 1e shall be maintained in presence of the following interferers at the receiver antenna port. Table 14 Wanted GSMR Signal Level on ARFCN 970 (dBm) Interferer(s) Characteristics Comment Mobile Input Level (dBm/200 kHz) ARFCN Freq.... |
34a2a4c5cf1c80685c7644a182c4327b | 102 933-1 | 9 Other requirements | RF characteristics which are not explicitly addressed in the present document shall be taken from ETSI TS 100 910 [4]. In addition, unless otherwise stated, the extended environmental requirements defined in the present document (see annex A) shall apply to specified equipment. Multi band MSs shall meet all requirement... |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 1 Scope | The present document describes the technical characteristics and methods of testing the improved receiver performance for professional mobile stations (professional MS), base stations (BS) and repeaters for the Pan European digital cellular communications system and Personal Communication Systems (PCS) operating in the... |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 2 References | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which ar... |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 2.1 Normative references | The following referenced documents are necessary for the application of the present document. [1] ETSI TS 100 607-1: "Digital cellular telecommunications system (Phase 2+); Mobile Station (MS) conformance specification; Part 1: Conformance specification (3GPP 11.10-1 Release 1999)". [2] ETSI TS 100 910: "Digital cellul... |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 2.2 Informative references | The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] ETSI TR 101 748: "Digital cellular telecommunications system (Phase 2+) (GSM); Abbreviations and acronyms (GSM 01.04 version 8.0.0 Release 1999)". [i.... |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 3 Abbreviations | For the purposes of the present document, the abbreviations given in TR 101 748 [i.1] apply. |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4 General test conditions | The relevant MS, BTS and repeaters transmit bands for the present document are the MS and BTS transmit bands as defined in TS 100 910 [2] and TS 102 932-1 [5]. The manufacturer shall declare: - which of the frequency bands defined in TS 102 933-2 [4] are supported by the BSS and the MS. This frequency range comprises t... |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.1 Base Station System (BSS) | The frequency bands for the Base Station System are given in table 3. Table 3: Frequency bands for ER-GSM Base Station Systems TX: RX: E-GSM900 925 MHz to 960 MHz 880 MHz to 915 MHz R-GSM900 921 MHz to 960 MHz 876 MHz to 915 MHz ER-GSM900 918 MHz to 960 MHz 873 MHz to 915 MHz NOTE 1: It is up to the operator to choose ... |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.1.1 Transmitter | Transmitter characteristics shall be the same as specified in TS 101 087 [3] with the exceptions that the requirements are applicable to the entire ER-GSM band. |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.1.2 Receivers | Receiver characteristics shall be the same as specified in TS 101 087 [3] with the exceptions that the requirements are applicable to the entire ER-GSM band. |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.2 Mobile Station (MS) | The frequency bands for the Mobile Stations are given in table 4. Table 4: Frequency bands for ER-GSM Mobile Station TX: RX: E-GSM900 880 MHz to 915 MHz 925 MHz to 960 MHz R-GSM900 876 MHz to 915 MHz 921 MHz to 960 MHz ER-GSM900 873 MHz to 915 MHz 918 MHz to 960 MHz |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.2.1 Transmitter | Transmitter characteristics shall be the same as specified in TS 100 607-1 [1] with the exceptions that the requirements are applicable to the entire ER-GSM band. ETSI ETSI TS 102 932-2 V1.1.1 (2011-11) 8 |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.2.2 Receivers | Receiver characteristics shall be the same as specified in TS 100 607-1 [1] and TS 102 933-2 [4] with the exceptions that the requirements are applicable to the entire ER-GSM band. |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.3 Repeaters | A repeater, as a bi-directional amplifier, can amplify and transmit a received MS signal in the MS transmit band, simultaneously it can amplify and transmit a received BTS signal in the BTS transmit band. NOTE: In some circumstances, for instance when an operator (or more than one operator who co-ordinate the use of re... |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.3.1 Transmitter | Transmitter characteristics shall be the same as specified in TS 151 026 [6] with the exceptions that the requirements are applicable to the entire ER-GSM band. |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 4.3.2 Receivers | Receiver characteristics shall be the same as specified in TS 151 026 [9] with the exceptions that the requirements are applicable to the entire ER-GSM Band. |
6ffac750f01e021518d746ff8c3b52b1 | 102 932-2 | 5 Other requirements | Equipment supporting the extended band shall also fulfill the requirements for equipment operating in the current R-GSM band to guarantee the compatibility between the equipment. Test cases which are not explicitly described in the present document shall be taken from the corresponding standards. ETSI ETSI TS 102 932-2... |
a541ae1ff4a82f536d9e1205a5551308 | 103 154 | 1 Scope | The present document defines system requirements for operation of mobile broadband service in the 2 300 - 2 400 MHz band under Licensed Shared Access (LSA). This band is allocated to the Mobile Service and identified for IMT globally in the ITU Radio Regulations. The objective of LSA is to enable access to this band fo... |
a541ae1ff4a82f536d9e1205a5551308 | 103 154 | 2 References | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which ar... |
a541ae1ff4a82f536d9e1205a5551308 | 103 154 | 2.1 Normative references | The following referenced documents are necessary for the application of the present document. Not applicable. |
a541ae1ff4a82f536d9e1205a5551308 | 103 154 | 2.2 Informative references | The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] ETSI TR 103 113 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); System Reference document (SRdoc); Mobile broadband service... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.