input stringclasses 1
value | instruction stringlengths 237 1.8k | output stringlengths 234 336 | category stringclasses 1
value | index stringlengths 1 5 |
|---|---|---|---|---|
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾎﾞｰﾙﾈｼﾞ部組立[/WorkName]
[WorkItem]1. BALL-SCREW の重要部品の確認を行う
3. 2.完成品にJOINT JOINT を取付
2. BALL-SCREW のねじ部の防錆油をふき取り､取付け面に砥石をかける
4. 3.完成品にTUBE を挿入
5. に4.完成品をBOLT で仮固定
6. 5.完成品にBEARING を挿入しC-RING で固定[/WorkItem]
[WorkPoint]JOINT の位置に注意
L用･R用区別... | [QualityItem]型式確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]型式が一致する事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]安全工程[/ProcessName] | information_extraction | 13594 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾎﾞｰﾙﾈｼﾞ部組立[/WorkName]
[WorkItem]1. BALL-SCREW の重要部品の確認を行う
3. 2.完成品にJOINT JOINT を取付
2. BALL-SCREW のねじ部の防錆油をふき取り､取付け面に砥石をかける
4. 3.完成品にTUBE を挿入
5. に4.完成品をBOLT で仮固定
6. 5.完成品にBEARING を挿入しC-RING で固定[/WorkItem]
[WorkPoint]JOINT の位置に注意
L用･R用区別... | [QualityItem]製造番号記録[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]製造番号転記[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13595 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]D-PIN圧入[/WorkName]
[WorkItem]1. にPIN を圧入する[/WorkItem]
[WorkPoint]出代:5mm
出代:5mm
出代:5mm
出代:5mm[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]出代:1mm
出代:1mm[/Words]
| [QualityItem]PIN出代[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]出代:5㎜±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13596 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]3㎜[/Size]
[ToolOther]1.2N･m[/ToolOther]
[WorkName]Y軸ﾎﾞｰﾙﾈｼﾞ部組立[/WorkName]
[WorkItem]1. BALL-SCREW の重要部品の確認を行う
3. 2.完成品にJOINT JOINT を取付
2. BALL-SCREW のねじ部の防錆油をふき取り､取付け面に砥石をかける
4. 3.完成品にTUBE を挿入
5. に4.完成品をBOLT で仮固定
6. 5.完成品にBEARING を挿入しC-RING で固定[/WorkItem]
[WorkPoint]L用･R用区別の... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]1.2N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13597 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]Yﾃｰﾌﾞﾙ取付ﾌﾟﾚｰﾄ部組立①[/WorkName]
[WorkItem]1. PLATE にPIN を取付
2. 1.完成品にTUBE-HOLDER JOINT をSCREW BOLT WASHER WASHER で取付
3. 2.完成品にTUBE TUBE TUBE TUBE CABLE-SUPPORT を取付[/WorkItem]
[WorkPoint]R用
L用
側面図
裏面図
R用
L用
裏面図[/WorkPoint]
[Tolk][/T... | [QualityItem]PIN出代[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]出代:5.0㎜±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13598 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Yﾃｰﾌﾞﾙ取付ﾌﾟﾚｰﾄ部組立①[/WorkName]
[WorkItem]1. PLATE にPIN を取付
2. 1.完成品にTUBE-HOLDER JOINT をSCREW BOLT WASHER WASHER で取付
3. 2.完成品にTUBE TUBE TUBE TUBE CABLE-SUPPORT を取付[/WorkItem]
[WorkPoint]R用
L用
側面図
裏面図
R用
L用
裏面図[/WorkPoint]
[Tolk][/Tolk]
[... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13599 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Yﾃｰﾌﾞﾙ取付ﾌﾟﾚｰﾄ部組立②[/WorkName]
[WorkItem]1. にDOG をBOLT WASHER で取付
2. 1.完成品にDOG SENSOR をBOLT WASHER BOLT WASHER ㉒で取付[/WorkItem]
[WorkPoint]R用
L用
側面図
R用
L用[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/Inspecti... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13600 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]Zθﾃｰﾌﾞﾙ取付ﾌﾟﾚｰﾄ部組立[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]PIN出代[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]出代:5.0㎜±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13601 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Zθﾃｰﾌﾞﾙ取付ﾌﾟﾚｰﾄ部組立[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13602 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]塗布確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所に塗布されている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13603 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]PIN出代[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]出代:5.0㎜±0.5㎜,2.5㎜±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13604 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-050[/Words]
| [QualityItem]型式確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]型式が一致する事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-050[/RecordMethod]
[Other]-[/Other]
[ProcessName]安全工程[/ProcessName] | information_extraction | 13605 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-051[/Words]
| [QualityItem]製造番号記録[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]製造番号転記[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-051[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13606 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾏｳﾝﾄ取付[/WorkName]
[WorkItem]1. にCABLE-SUPPORT を取付ける[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13607 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13608 | |
[ToolName]XY組立ﾍﾞｰｽ[/ToolName]
[Size][/Size]
[ToolOther]FM-3506[/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]FM-3506[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13609 | |
[ToolName]ﾌﾞﾛｯｸｹﾞｰｼﾞ[/ToolName]
[Size]5㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13610 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]真直度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13611 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]4㎜[/Size]
[ToolOther]5.9N･m[/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]5.9N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13612 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13613 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]4㎜[/Size]
[ToolOther]5.9N･m[/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]5.9N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13614 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立③[/WorkName]
[WorkItem]1. に をBOLT BOLT で仮固定
2. 1.完成品に を挿入しBLOCK BOLT で仮固定
3. 2.完成品にCOLLAR を挿入しNUT で締付[/WorkItem]
[WorkPoint]付属ｾｯﾄﾋﾞｽ(PICE含)
ﾅｯﾄ段付き部
NUT ﾅｯﾄの段付側をCOLLAR ｶﾗｰ側に向けて取付ける事
本締め工程:SD-A044837-019
本締め工程:SD-A044837-019
R用
... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13615 | |
[ToolName]ﾄﾙｸｽﾊﾟﾅ[/ToolName]
[Size]22㎜[/Size]
[ToolOther]8.7N･m[/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立③[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]付属ｾｯﾄﾋﾞｽ(PICE含)
ﾅｯﾄ段付き部
NUT ﾅｯﾄの段付側をCOLLAR ｶﾗｰ側に向けて取付ける事[/WorkPoint]
[Tolk]8.7N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]1.完成品
W... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]8.7N･m±10%[/StdVal]
[Method]ﾄﾙｸｽﾊﾟﾅ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13616 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立④[/WorkName]
[WorkItem]1. X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄの平行出し
2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の精度出し後ｽﾄｯﾊﾟｰﾌﾞﾛｯｸを本締め[/WorkItem]
[WorkPoint]X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ
平行度:0.01㎜以下
調整後本締め
X軸ﾎﾞｰﾙﾈｼﾞ
基準LM
平行度:0.01㎜以下
水平度:0.02㎜以下(参考値)
基準LM
水平方向(上面)
平行方向(側面)
L... | [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13617 | |
[ToolName]ｼｯｸﾈｽｹﾞｰｼﾞ[/ToolName]
[Size]0.01㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]LM取付[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]LINEAR-WAY の基準側を のD-PIN側にする事
D-PINの場所以外は仮固定の事
基準･従動側共に0.02mm以内
LM取付ﾎﾞﾙﾄは穴1個飛ばして取付最後の2本だけ連続で取付[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/Inspect... | [QualityItem]隙間確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]ｼｯｸﾈｽｹﾞｰｼﾞ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13618 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立④[/WorkName]
[WorkItem]1. X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄの平行出し
2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の精度出し後ｽﾄｯﾊﾟｰﾌﾞﾛｯｸを本締め[/WorkItem]
[WorkPoint]X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ
平行度:0.01㎜以下
調整後本締め
X軸ﾎﾞｰﾙﾈｼﾞ
基準LM
平行度:0.01㎜以下
水平度:0.02㎜以下(参考値)
基準LM
水平方向(上面)
平行方向(側面)
L... | [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13619 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立④[/WorkName]
[WorkItem]1. X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄの平行出し
2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の精度出し後ｽﾄｯﾊﾟｰﾌﾞﾛｯｸを本締め[/WorkItem]
[WorkPoint]X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ
平行度:0.01㎜以下
調整後本締め
X軸ﾎﾞｰﾙﾈｼﾞ
基準LM
平行度:0.01㎜以下
水平度:0.02㎜以下(参考値)
基準LM
水平方向(上面)
平行方向(側面)
L... | [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.02㎜以下(参考値)[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13620 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立⑤[/WorkName]
[WorkItem]1. ﾎﾞｰﾙﾈｼﾞ部ｽﾗｽﾄ方向ｶﾞﾀ確認
2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の芯振れの確認[/WorkItem]
[WorkPoint]X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ
ｽﾗｽﾄｶﾞﾀ:0.01㎜以下
芯振れ:0.02㎜以下
ﾈｼﾞ端部を30Nの力で押す
X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/Inspe... | [QualityItem]ｽﾗｽﾄ確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13621 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立⑤[/WorkName]
[WorkItem]1. ﾎﾞｰﾙﾈｼﾞ部ｽﾗｽﾄ方向ｶﾞﾀ確認
2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の芯振れの確認[/WorkItem]
[WorkPoint]X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ
ｽﾗｽﾄｶﾞﾀ:0.01㎜以下
芯振れ:0.02㎜以下
ﾈｼﾞ端部を30Nの力で押す
X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/Inspe... | [QualityItem]芯ﾌﾞﾚ確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.02㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13622 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立⑥[/WorkName]
[WorkItem]◆1. にSCREW を取付しSPACER を取付
◆2. 1.完成品にSCREW を取付しSPACER を取付
3. 2.完成品にBLOCK BLOCK BLOCK BLOCK をBOLT で取付
4. 3.完成品にSENSOR をBOLT WASHER WASHER で取付[/WorkItem]
[WorkPoint]側面図
側面図
側面図
㉖ロックタイト塗布
㉖ロックタイト塗布[/WorkPoint... | [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所に塗布ｺﾞﾑ粒:2[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ﾛｯｸﾀｲﾄ243[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 13623 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立⑦[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]動作確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]正常な事(引っ掛かり等無き事)[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13624 | |
[ToolName]ﾃﾝｼｮﾝｹﾞｰｼﾞ[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立⑦[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]摺動確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]40cN･m以下ﾊﾞﾗﾂｷ15cN･m以下[/StdVal]
[Method]ﾄﾙｸｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13625 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸ﾌﾚｰﾑ部組立⑧[/WorkName]
[WorkItem]1. の配管干渉をチェックし㉖で結束
2. 1.完成品の配管を ･ に接続[/WorkItem]
[WorkPoint]LMﾚｰﾙやﾎﾞｰﾙねじ等と接触し無い事を確認
L･R共に確認する事[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]検査表 :◆X軸組立 配管... | [QualityItem]干渉確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]LMﾚｰﾙやﾎﾞｰﾙねじ等と接触し無い事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13626 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem]1. BASE-FRAME(Y) の表面にPIN LINEAR-WAY を圧入
2. ④の重要部品の確認
3. ④に塗布されている防錆油を拭取る[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]この作業では... | [QualityItem]PIN出代[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]出代:2.5㎜±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13627 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem]1. BASE-FRAME(Y) の表面にPIN LINEAR-WAY を圧入
2. ④の重要部品の確認
3. ④に塗布されている防錆油を拭取る
4. 1.完成品に3.完成品をBOLT で仮固定する[/WorkItem]
[WorkPoint]型式確認及び､ｼﾘｱﾙ№記録
出代:5㎜
出代:2.5㎜
LMｶﾞｲﾄﾞ基準面(加工面)を内側に取付ける
本締め工程:SD-A044837-025
LMｶﾞｲﾄﾞ基... | [QualityItem]型式確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]型式が一致する事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]安全工程[/ProcessName] | information_extraction | 13628 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/100[/Size]
[ToolOther][/ToolOther]
[WorkName]LM取付[/WorkName]
[WorkItem]1. にLINEAR-WAY をBOLT で取付ける
2. 1完成品の精度出し[/WorkItem]
[WorkPoint]LINEAR-WAY の基準面と のD-PINに隙間無き事
基準側ﾘﾆｱはｽﾄﾚｰﾄｴｯｼﾞ､従動側は基準側にて精度出しを行う事[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionI... | [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]20μm以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13629 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem]1. BASE-FRAME(Y) の表面にPIN LINEAR-WAY を圧入
2. ④の重要部品の確認
3. ④に塗布されている防錆油を拭取る
4. 1.完成品に3.完成品をBOLT で仮固定する[/WorkItem]
[WorkPoint]型式確認及び､ｼﾘｱﾙ№記録
出代:5㎜
出代:2.5㎜
LMｶﾞｲﾄﾞ基準面(加工面)を内側に取付ける
本締め工程:SD-A044837-025
LMｶﾞｲﾄﾞ基... | [QualityItem]製造番号記録[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]製造番号転記[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13630 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立①[/WorkName]
[WorkItem]1. BASE-FRAME(Y) の表面にPIN LINEAR-WAY を圧入
2. ④の重要部品の確認
3. ④に塗布されている防錆油を拭取る
4. 1.完成品に3.完成品をBOLT で仮固定する[/WorkItem]
[WorkPoint]型式確認及び､ｼﾘｱﾙ№記録
出代:5㎜
出代:2.5㎜
LMｶﾞｲﾄﾞ基準面(加工面)を内側に取付ける
本締め工程:SD-A044837-025
LMｶﾞｲﾄﾞ基... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13631 | |
[ToolName]ﾌﾞﾛｯｸｹﾞｰｼﾞ[/ToolName]
[Size]5㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]従動側[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]1.完成品[/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13632 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]従動側
従動側[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]1.完成品
1.完成品
WWYJ-5300-049[/Words]
| [QualityItem]真直度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13633 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]従動側
従動側[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]1.完成品
1.完成品
WWYJ-5300-049[/Words]
| [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13634 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]3㎜[/Size]
[ToolOther]N･m[/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]従動側[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]1.完成品[/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]3.5N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13635 | |
[ToolName]ﾉｷﾞｽ[/ToolName]
[Size]300㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]従動側[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]1.完成品[/Words]
| [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]寸法:190㎜±1㎜以内[/StdVal]
[Method]ﾉｷﾞｽ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13636 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立③[/WorkName]
[WorkItem]1. に をBOLT BOLT で仮固定
2. 1.完成品に を挿入しBLOCK BOLT で仮固定
3. 2.完成品にWASHER を挿入しNUT で締付[/WorkItem]
[WorkPoint]本締め工程:SD-A044837-027
本締め工程:SD-A044837-027
付属ｾｯﾄﾋﾞｽ(PICE含)
ﾅｯﾄ段付き部
NUT ﾅｯﾄの段付側をWASHER ｶﾗｰ側に向けて取付ける事[/Wo... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13637 | |
[ToolName]ﾄﾙｸｽﾊﾟﾅ[/ToolName]
[Size]19㎜[/Size]
[ToolOther]6.9N･m[/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立③[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]付属ｾｯﾄﾋﾞｽ(PICE含)
ﾅｯﾄ段付き部
NUT ﾅｯﾄの段付側をWASHER ｶﾗｰ側に向けて取付ける事[/WorkPoint]
[Tolk]6.9N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]6.9N･m±10%[/StdVal]
[Method]ﾄﾙｸｽﾊﾟﾅ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13638 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立④[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下(ﾓｰﾀｰﾌﾞﾗｹｯﾄ)[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13639 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾍﾞｱ配線(内側)取付け[/WorkName]
[WorkItem]2. 1完成品を に入れ両端に を取付け㉖で固定する
1. のケーブルサポートに㉖を通す（4箇所）
3. ㉖の不要部分をカットする[/WorkItem]
[WorkPoint]㉖の頭が、ケーブルサポートの下面になる様挿入する
ｹｰﾌﾞﾙｻﾎﾟｰﾄを上面にして入れる
ｹｰﾌﾞﾙｻﾎﾟｰﾄ
ｶｯﾄする[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/Inspection... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13640 | |
[ToolName]ｽﾄﾚｰﾄｴｯｼﾞ[/ToolName]
[Size]1000㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]LM取付[/WorkName]
[WorkItem]1. にLINEAR-WAY をBOLT で取付ける
2. 1完成品の精度出し[/WorkItem]
[WorkPoint]LINEAR-WAY の基準面と のD-PINに隙間無き事
基準側ﾘﾆｱはｽﾄﾚｰﾄｴｯｼﾞ､従動側は基準側にて精度出しを行う事[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem]... | [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]20μm以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13641 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立④[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下(ﾎﾞｰﾙﾈｼﾞ)[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13642 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]2/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立④[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.02㎜以下(参考値)[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13643 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立⑤[/WorkName]
[WorkItem]1. ﾎﾞｰﾙﾈｼﾞ部ｽﾗｽﾄ方向ｶﾞﾀ確認
2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の芯振れの確認[/WorkItem]
[WorkPoint]Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ
ｽﾗｽﾄｶﾞﾀ:0.001㎜以下
L用･R用共に測定する事
芯振れ:0.01㎜以下
L用･R用共に測定する事
Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ[/WorkPoint]
[Tolk][/Tolk]
[Inspec... | [QualityItem]ｽﾗｽﾄ確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.001㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13644 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立⑤[/WorkName]
[WorkItem]1. ﾎﾞｰﾙﾈｼﾞ部ｽﾗｽﾄ方向ｶﾞﾀ確認
2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の芯振れの確認[/WorkItem]
[WorkPoint]Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ
ｽﾗｽﾄｶﾞﾀ:0.001㎜以下
L用･R用共に測定する事
芯振れ:0.01㎜以下
L用･R用共に測定する事
Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ[/WorkPoint]
[Tolk][/Tolk]
[Inspec... | [QualityItem]芯ﾌﾞﾚ確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.01㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13645 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立⑥[/WorkName]
[WorkItem]1. にFRAME FRAME をBOLT WASHER で取付
2. 1.完成品にBRACKET をBOLT WASHER で取付
3. 2.完成品にSCREW NUT WASHER STOPPER を取付[/WorkItem]
[WorkPoint]ﾓｰﾀｰ側側面図
反対側側面図
L用
R用
ﾓｰﾀｰ側側面図
ﾓｰﾀｰ側側面図
L用のみ取付
ﾓｰﾀｰ側側面図
上面図[/WorkP... | [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]寸法:30.0㎜±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13646 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立⑦[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]動作確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]引っかかり等無い事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13647 | |
[ToolName]ﾃﾝｼｮﾝｹﾞｰｼﾞ[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立⑦[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]摺動確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]25cN･m以下ﾊﾞﾗﾂｷ10cN･m以下[/StdVal]
[Method]ﾄﾙｸｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13648 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立⑧[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13649 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立⑨[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]真直度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.02㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13650 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/1000[/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸ﾌﾚｰﾑ部組立⑨[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.03㎜以下(参考値)[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13651 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]金ﾆｽ塗布･ﾌﾚｰﾑ取付[/WorkName]
[WorkItem]◆1. に金ﾆｽを塗布する
2. 1完成品に をBOLT で取付ける[/WorkItem]
[WorkPoint]加工面に塗布する事
LMｶﾞｲﾄﾞに金ﾆｽが付着しない様にする事
取付位置に注意
ﾌﾚｰﾑを外寄せで取付(4箇所)[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionIt... | [QualityItem]塗布確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所に塗布されている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]金ﾆｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 13652 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]XY軸ﾓｰﾀｰ取付[/WorkName]
[WorkItem]1. にCOUPLING COUPLING を挿入し をBOLT WASHER BOLT WASHER で取付[/WorkItem]
[WorkPoint]COUPLING ･COUPLING のｶｯﾌﾟﾘﾝｸﾞは締め付け無い事
COUPLING COUPLING の取付方向に注意
Ⅹ軸ﾓｰﾀｰ(K006-1 L用)
Y軸ﾓｰﾀｰ(K006-2 L用)
Ⅹ軸ﾓｰﾀｰ(K006-1 R用)
Y軸ﾓｰﾀｰ(K00... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13653 | |
[ToolName]ﾓｰﾀ原点出し治具[/ToolName]
[Size][/Size]
[ToolOther]FM-3446[/ToolOther]
[WorkName]X軸原点調整[/WorkName]
[WorkItem]1. のX軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続
3. X軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け
2. X軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
... | [QualityItem]原点確認[/QualityItem]
[ToolManageNo]FM-3446[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]原点位置である事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13654 | |
[ToolName]原点出しﾋﾟﾝ(φ12-φ8段付きﾋﾟﾝ)[/ToolName]
[Size][/Size]
[ToolOther]FM-3467[/ToolOther]
[WorkName]X軸原点調整[/WorkName]
[WorkItem]1. のX軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続
3. X軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け
2. X軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/Insp... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]FM-3467[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13655 | |
[ToolName]ﾄﾙｸｽﾊﾟﾅ[/ToolName]
[Size]22㎜[/Size]
[ToolOther]63.7N･m[/ToolOther]
[WorkName]X軸原点調整[/WorkName]
[WorkItem]1. のX軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続
3. X軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け
2. X軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]ﾓｰﾀｰ側63.7N･m±10%[/StdVal]
[Method]ﾄﾙｸｽﾊﾟﾅ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13656 | |
[ToolName]ﾄﾙｸｽﾊﾟﾅ[/ToolName]
[Size]19㎜[/Size]
[ToolOther]39.2N･m[/ToolOther]
[WorkName]X軸原点調整[/WorkName]
[WorkItem]1. のX軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続
3. X軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け
2. X軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]ﾈｼﾞ側39.2N･m±10%[/StdVal]
[Method]ﾄﾙｸｽﾊﾟﾅ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13657 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]X軸原点調整[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]7㎜[/Words]
| [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]寸法:155.0㎜±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13658 | |
[ToolName]ﾓｰﾀ原点出し治具[/ToolName]
[Size][/Size]
[ToolOther]FM-3446[/ToolOther]
[WorkName]Y軸原点調整[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]原点確認[/QualityItem]
[ToolManageNo]FM-3446[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]原点位置である事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13659 | |
[ToolName]原点出しﾋﾟﾝ(φ12-φ8段付きﾋﾟﾝ)[/ToolName]
[Size][/Size]
[ToolOther]FM-3467[/ToolOther]
[WorkName]Y軸原点調整[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]原点確認[/QualityItem]
[ToolManageNo]FM-3467[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]原点位置である事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13660 | |
[ToolName]ﾄﾙｸｽﾊﾟﾅ[/ToolName]
[Size]17㎜[/Size]
[ToolOther]19.6N･m[/ToolOther]
[WorkName]Y軸原点調整[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]19.6N･m±10%[/StdVal]
[Method]ﾄﾙｸｽﾊﾟﾅ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13661 | |
[ToolName]ﾄﾙｸｽﾊﾟﾅ[/ToolName]
[Size]22㎜[/Size]
[ToolOther]34.3N･m[/ToolOther]
[WorkName]Y軸原点調整[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]34.3N･m±10%[/StdVal]
[Method]ﾄﾙｸｽﾊﾟﾅ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13662 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]金ﾆｽ塗布･ﾌﾚｰﾑ取付[/WorkName]
[WorkItem]◆1. に金ﾆｽを塗布する
2. 1完成品に をBOLT で取付ける[/WorkItem]
[WorkPoint]加工面に塗布する事
LMｶﾞｲﾄﾞに金ﾆｽが付着しない様にする事
取付位置に注意[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 13663 | |
[ToolName]ｾﾝｻｰﾁｪｯｶｰ[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸原点調整[/WorkName]
[WorkItem]1. のY軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続
3. Y軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け
2. Y軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる
4. Y軸原点の状態でﾄﾞｸﾞ位置を調整する[/WorkItem]
[WorkPoint]L･R共に実施の事
ﾓｰﾀｰ側から規定ﾄﾙｸで締結の事
ﾓｰﾀｰ原点にする
原点PHｾﾝｻｰ位置を確認する
L･R共に実施の事
L･R共に実施の... | [QualityItem]位置確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示位置であること[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13664 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾘﾆｱｶﾞｲﾄﾞ･ﾎﾞｰﾙﾈｼﾞ部ｸﾞﾘｰｽ給油[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]X軸LM複数回ﾎﾟﾝﾌﾟしLMに届かせ指示箇所に薄く塗布[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ｸﾞﾘｰｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 13665 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾘﾆｱｶﾞｲﾄﾞ･ﾎﾞｰﾙﾈｼﾞ部ｸﾞﾘｰｽ給油[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]Y軸LM1回ﾎﾟﾝﾌﾟしLMに届かせ指示箇所に薄く塗布[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ｸﾞﾘｰｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 13666 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾘﾆｱｶﾞｲﾄﾞ･ﾎﾞｰﾙﾈｼﾞ部ｸﾞﾘｰｽ給油[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]X軸ﾎﾞｰﾙﾈｼﾞ複数回ﾎﾟﾝﾌﾟしﾎﾞｰﾙﾈｼﾞに届かせ指示箇所に薄く塗布[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ｸﾞﾘｰｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 13667 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾘﾆｱｶﾞｲﾄﾞ･ﾎﾞｰﾙﾈｼﾞ部ｸﾞﾘｰｽ給油[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]Y軸ﾎﾞｰﾙﾈｼﾞ複数回ﾎﾟﾝﾌﾟしﾎﾞｰﾙﾈｼﾞに届かせ指示箇所に薄く塗布[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ｸﾞﾘｰｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 13668 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾎﾞｰﾙﾈｼﾞｶﾊﾞｰ部取付①[/WorkName]
[WorkItem]1. に をPLATE PLATE BOLT で取付
2. 1.完成品に をBOLT WASHER で取付[/WorkItem]
[WorkPoint] が自重で撓むため 中央付近を上に持ち上げながらBOLT で締結[/WorkPoint]
[Tolk]側面図
上面図
側面図
上面図[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/I... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13669 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]ﾎﾞｰﾙﾈｼﾞｶﾊﾞｰ部取付②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]隙間確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]隙間:4.0㎜±2.5㎜3.0㎜±1.0㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13670 | |
[ToolName]測定治具[/ToolName]
[Size][/Size]
[ToolOther]FM-6043[/ToolOther]
[WorkName]Zθﾃｰﾌﾞﾙ部取付①[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]FM-6043[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13671 | |
[ToolName]測定治具[/ToolName]
[Size][/Size]
[ToolOther]FM-6043[/ToolOther]
[WorkName]Zθﾃｰﾌﾞﾙ部取付②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]FM-6043[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13672 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/100[/Size]
[ToolOther][/ToolOther]
[WorkName]Zθﾃｰﾌﾞﾙ部取付②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.2㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13673 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ｽﾄｯﾊﾟｰ取付[/WorkName]
[WorkItem]1. に をBOLT WASHER で取付け､ をBOLT WASHER で取付ける[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13674 | |
[ToolName]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/ToolName]
[Size]1/100[/Size]
[ToolOther][/ToolOther]
[WorkName]Zθﾃｰﾌﾞﾙ部取付②[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]平行度確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]1回/半年[/ToolCycle]
[ToolRecord]校正成績書[/ToolRecord]
[StdVal]0.02㎜以下0.05㎜以下[/StdVal]
[Method]てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13675 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem]1. に をBOLT WASHER で取付
2. に をBOLT WASHER BOLT WASHER で取付[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk]側面図[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]×4
×10
×4
×4
×1... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13676 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ｹｰﾌﾞﾙﾍﾞｱ取付[/WorkName]
[WorkItem]1. にCABLE-BEAR SHEET をBOLT WASHER WASHER で取付
2. にCABLE-BEAR SHEET をBOLT WASHER WASHER で取付[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk]側面図
正面図
前面図[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/Inspec... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13677 | |
[ToolName]ｺﾝﾍﾞｯｸｽ[/ToolName]
[Size]3.5m[/Size]
[ToolOther][/ToolOther]
[WorkName]Zθ配線･配管[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示寸法各±1㎜[/StdVal]
[Method]ｺﾝﾍﾞｯｸｽ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13678 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Zθ配線･配管[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]干渉確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]ｹｰﾌﾞﾙﾍﾞｱ前後の配管ｸﾗﾝﾌﾟ部分のねじれ､潰れ等無い事確認の事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13679 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸配線[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-109[/Words]
| [QualityItem]接続確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り接続出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-109[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13680 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Y軸配線[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]
WWYJ-5300-049[/Words]
| [QualityItem]干渉確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]ｹｰﾌﾞﾙﾍﾞｱ前後の配管ｸﾗﾝﾌﾟ部分のねじれ､潰れ等無い事確認の事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13681 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸配線[/WorkName]
[WorkItem]1. にCABLE CABLE を取付
3. 2.完成品の真空配管確認
2. 1.完成品の接続確認[/WorkItem]
[WorkPoint]L･R用共に確認の事
ｹｰﾌﾞﾙﾍﾞｱ入り口側から正圧(0.08MPa)を入れ､ 反対側の流量を測定 22~35L/min[/WorkPoint]
[Tolk]前面図[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/... | [QualityItem]接続確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り接続出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-109[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13682 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]X軸配線[/WorkName]
[WorkItem]1. にCABLE CABLE を取付
3. 2.完成品の真空配管確認
2. 1.完成品の接続確認[/WorkItem]
[WorkPoint]L･R用共に確認の事
ｹｰﾌﾞﾙﾍﾞｱ入り口側から正圧(0.08MPa)を入れ､ 反対側の流量を測定 22~35L/min[/WorkPoint]
[Tolk]前面図[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/... | [QualityItem]設定確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]ｹｰﾌﾞﾙﾍﾞｱ入り口側から正圧(0.08MPa)を入れ､反対側の流量を測定22~35L/min[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-049[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13683 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]XY軸ｶﾊﾞｰ取付[/WorkName]
[WorkItem]1. にCOVER COVER をBOLT で取付
2. 1.完成品にCOVER COVER COVER をSCREW で取付
3. 2.完成品にCOVER COVER をSCREW で取付[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk]Y軸上面図
X軸前面図
X軸上面図
Zθ軸上面図[/Tolk]
[InspectionNo][/InspectionNo]
[Insp... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13684 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ｾﾝｻｰ取付[/WorkName]
[WorkItem]1. に をBOLT WASHER で取付け､ をBOLT WASHER で取付ける[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13685 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]Zθ軸ｶﾊﾞｰ取付[/WorkName]
[WorkItem]1. にCOVER をSCREW で取付
2. 1.完成品にCOVER COVER COVER をSCREW で取付[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk]Zθ軸背面図
Zθ軸左側面拡大図
Zθ軸背面図
Zθ軸右側面拡大図
Zθ軸前面
Zθ軸左側面
Zθ軸右側面
Zθ軸上面
Zθ軸前面
Zθ軸左側面
Zθ軸右側面
Zθ軸上面
Zθ軸背面
Zθ軸... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13686 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]払い出し[/WorkName]
[WorkItem]1. ~SPACER ･BOLT ~WASHER をMTKA045171(本体部)へ払い出し[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]払出確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]作業指示の払出である事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13687 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]θﾃｰﾌﾞﾙﾛｯｸ機構組立①[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]BLOCK ･BLOCK は1.完成品に押し当てながら固定
BLOCK ･BLOCK は1.完成品に押し当てながら固定[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]ﾋﾟﾝ出代[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]出代2.5±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13688 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]θﾃｰﾌﾞﾙﾛｯｸ機構組立②[/WorkName]
[WorkItem]1. に を取付
2. 1.完成品(L・R共)及びPIN ～CABLE-SUPPORT ・BOLT ～㉑をMTKA04388(Mテーブル用)へ払い出し[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words... | [QualityItem]ﾘｰﾄﾞSW寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]･端面より10±0.5㎜･端面合わせ(±0.5㎜)[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13689 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]TCP供給部連結ﾌﾞﾗｹｯﾄ組立て[/WorkName]
[WorkItem]1. BRACKET にSHAFT をBOLT で取付ける｡
2. BRACKET にBOLT WASHER (供給部連結用ﾎﾞﾙﾄ)を仮付けする｡
3. SHAFT にBOLT WASHER (供給部連結用ﾎﾞﾙﾄ)を仮付けする｡
4. 2.3の完成品をAM架台背面にBOLT WASHER で取付ける｡
2完成品
3完成品[/WorkItem]
[WorkPoint][/WorkPoint]
... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13690 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ｲｵﾅｲｻﾞｰ組立[/WorkName]
[WorkItem]1. IONIZER 除電ﾊﾞｰ部にSPEED-CONTROLLER を取付け
3. 2の完成品にBRACKET をBOLT WASHER ㉒で取付け
4. PLATE にIONIZER コントローラ部をBOLT WASHER ㉒で取付け
5. NUT SUPPORT BOLT WASHER ､BLOCK BOLT WASHER を付属
2. IONIZER ｴﾝﾄﾞﾕﾆｯﾄを除電ﾊﾞｰ部に付属ﾈｼﾞで取付け[/Wo... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13691 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ｲｵﾅｲｻﾞｰ配線準備[/WorkName]
[WorkItem]1. CABLE にLABEL TERMINAL PROCESS (LABEL TERMINAL PROCESS )を取付け
2. CABLE CABLE (CABLE CABLE )を付属[/WorkItem]
[WorkPoint]合わせる
合わせる
合わせる
合わせる
上流はCABLE CABLE ､下流はCABLE CABLE を付属
上流はLABEL TERMINAL PROCESS ､下流はLA... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13692 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-6457[/ToolOther]
[WorkName]ﾏｸﾞﾈｯﾄ取付け[/WorkName]
[WorkItem]1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]⇒ﾏｸﾞﾈｯﾄ中
⇒ﾏｸﾞﾈｯﾄ大[/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]FM-6457[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 13693 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.