input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "下受けﾋﾟﾝ(長･短)",
"Size": "",
"ToolOther": "",
"WorkName": "安全ﾃｽﾄ(下受けﾋﾟﾝ検出ﾚｰﾝ1)ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様",
"WorkItems": [
"3. ｴﾗｰ停止後下受けﾋﾟﾝを立て換え､ﾚｰﾙとﾋﾟﾝ間に隙間がある事を確認する",
"■2. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て､幅寄せを行った時､検出ｾﾝｻにて即停止することを確認する",
"1. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て手動で幅寄せを行い 検出ｾﾝｻがOFF(緑のみ点灯)することを確認する"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-B01",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ(長･短)",
"Size": "",
"ToolOther": "",
"WorkName": "安全ﾃｽﾄ(下受けﾋﾟﾝ検出ﾚｰﾝ2)ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様",
"WorkItems": [
"1. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て手動で幅寄せを行い 検出ｾﾝｻがOFF(緑のみ点灯)することを確認する",
"■2. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て､幅寄せを行った時､検出ｾﾝｻにて即停止することを確認する",
"3. ｴﾗｰ停止後下受けﾋﾟﾝを立て換え､ﾚｰﾙとﾋﾟﾝ間に隙間がある事を確認する"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-B01",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "安全ﾃｽﾄ(ｵﾌﾟｼｮﾝ:延長ｺﾝﾍﾞｱ開口部ｾﾝｻ)",
"WorkItems": [
"■2. を押しながら開始を押下し原点復帰中に左側延長ｺﾝﾍﾞｱ開口部ｾﾝｻを遮光すると､ 設備が即停止\u0026ｴﾗｰ表示されることを確認する",
"■3. 右側の延長ｺﾝﾍﾞｱ開口部ｾﾝｻも同様に確認する",
"1. 延長ｺﾝﾍﾞｱのｹｰﾌﾞﾙCNEXL･CNEXRを､本体に接続する"
],
"WorkPoints": [
... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-B01",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ診断用SD",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ診断①",
"WorkItems": [
"7. ⑥ 操作ﾊﾟﾈﾙの を押しながら 『計測ｽﾀｰﾄ』を押す",
"2. ① 《ﾒﾝﾃﾅﾝｽ》 を押す",
"4. ③ 《ﾍｯﾄﾞ診断》 を押す",
"5. ④ 4項目を押し選択を解除する",
"3. ② 《ﾍｯﾄﾞ》 を押す",
"1. ㉖ ヘッド診断用SDをドライブに挿入する",
"6. ⑤ 3項目の選択が選択されているのを確認する"... | {
"QualityItem": "表示確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｴﾗｰ無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ診断用SD",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ診断②",
"WorkItems": [
"1. ① 計測結果を確認し､ｴﾗｰ(黄色)がないことを確認する",
"2. ② 《戻る》 を押す",
"3. ③ 《ﾃﾞｰﾀ転送》 を押す",
"4. ④ 《LNB 》 を押し､LNBにﾃﾞｰﾀを転送する",
"5. ⑤ 《TBL2》 を押し､5~13までを同様に実施する",
"6. LNBにて転送ﾃﾞｰﾀにｴﾗｰが無いことを確認する"
],
"... | {
"QualityItem": "表示確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｴﾗｰ無き事",
"Method": "目視",
"RecordMethod": "WETE-G002-B01",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "駆動部ﾌﾚｰﾑ吊り上げ、金ﾆｽ塗装",
"WorkItems": [
"◆2. FRAME の指示した場所以外の加工面に金ﾆｽ塗装を行う",
"1. FRAME 本圧着ﾌﾚｰﾑの加工面(下面以外)全てを油砥石で均す",
"◆3. FRAME をﾘﾌﾀｰ(ｸﾚｰﾝ)で吊り上げ本圧着ﾌﾚｰﾑ下面を油砥石で均す"
],
"WorkPoints": [
"ﾓｰﾀｰ取付け面",
"ﾌﾚｰﾑ前側基準面(LMｶﾞｲﾄﾞ取付基準面)",
... | {
"QualityItem": "金ﾆｽ塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "駆動部ﾌﾚｰﾑ吊り上げ、金ﾆｽ塗装",
"WorkItems": [
"◆2. FRAME の指示した場所以外の加工面に金ﾆｽ塗装を行う",
"1. FRAME 本圧着ﾌﾚｰﾑの加工面(下面以外)全てを油砥石で均す",
"◆3. FRAME をﾘﾌﾀｰ(ｸﾚｰﾝ)で吊り上げ本圧着ﾌﾚｰﾑ下面を油砥石で均す"
],
"WorkPoints": [
"ﾓｰﾀｰ取付け面",
"ﾌﾚｰﾑ前側基準面(LMｶﾞｲﾄﾞ取付基準面)",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入",
"WorkItems": [
"1. にPIN を圧入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"出代1.5mm",
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:1.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入",
"WorkItems": [
"1. にPIN を圧入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"出代1.5mm",
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:2.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入",
"WorkItems": [
"1. にPIN を圧入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"出代1.5mm",
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸LMｶﾞｲﾄﾞ取付け①",
"WorkItems": [],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. にLINEAR-WAY をBOLT で固定する(従動側は仮固定)",
"･L... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸LMｶﾞｲﾄﾞ取付け①",
"WorkItems": [],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. にLINEAR-WAY をBOLT で固定する(従動側は仮固定)",
"･L... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "H軸LMｶﾞｲﾄﾞ取付け①",
"WorkItems": [],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. にLINEAR-WAY をBOLT で固定する(従動側は仮... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "H軸LMｶﾞｲﾄﾞ取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"測定域 200mm範囲で0.01mm以下",
"◆作業者安全作業",
"LMｶﾞｲﾄﾞ取付け完了後周りに塗布する",
"平行度:0.01mm以下"... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "60㎜の範囲で0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸LMｶﾞｲﾄﾞ取付け②",
"WorkItems": [
"1. LMｶﾞｲﾄﾞ従動側(R側)の取付け位置を調整する",
"◆3. 取付け終了後､周りに金ﾆｽ塗布を行う"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "金ﾆｽ塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け①",
"WorkItems": [
"1. にLINEAR-WAY をBOLT で仮固定する"
],
"WorkPoints": [
"･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝに当付ける(隙間:0.01㎜以下)",
"基準側(研磨面)を写真左側に向ける",
"基準側(研磨面)を写真左側に向ける",
"SD-0169115-... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-064",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け①",
"WorkItems": [
"1. にLINEAR-WAY をBOLT で仮固定する"
],
"WorkPoints": [
"･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝに当付ける(隙間:0.01㎜以下)",
"基準側(研磨面)を写真左側に向ける",
"基準側(研磨面)を写真左側に向ける",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-064",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100㎜",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾋﾟﾝ当て基準隙間確認",
"◆作業者安全作業",
"平行度全ｽﾄﾛｰｸで0.02mm以内(左ﾋﾟﾝ基準にて)",
"... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "全ｽﾄﾛｰｸで0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-064",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100㎜",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾋﾟﾝ当て基準隙間確認",
"◆作業者安全作業",
"平行度全ｽﾄﾛｰｸで0.02mm以内(左ﾋﾟﾝ基準にて)",
"... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-064",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②",
"WorkItems": [
"1. 基準側ｶﾞｲﾄﾞ(手前)のﾌﾚｰﾑ端面との平行度を調整する",
"2. 基準側LMｶﾞｲﾄﾞ(手前)に対する従動側LMｶﾞｲﾄﾞ(奥)の平行度を調整する",
"◆3. 調整後のLMｶﾞｲﾄﾞﾚｰﾙ周辺及び､ﾌﾚｰﾑ前端面に金ﾆｽを塗布する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮ... | {
"QualityItem": "金ﾆｽ塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立①",
"WorkItems": [
"◆1. BRACKET 部品の指定以外の加工面に金ﾆｽ塗装を行う",
"2.1完成品にPIN を圧入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "金ﾆｽ塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立①",
"WorkItems": [
"◆1. BRACKET 部品の指定以外の加工面に金ﾆｽ塗装を行う",
"2.1完成品にPIN を圧入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立②",
"WorkItems": [],
"WorkPoints": [
"STOPPER 型式:BNF1605-5RRGT\u002B157LC5(33437272D000)※ﾎﾞｰﾙｽﾌﾟﾗｲﾝが包装されているｼｰﾙに記載",
"ｼﾘｱﾙ№",
"型式確認･ｼﾘｱﾙ№記入",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"To... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立②",
"WorkItems": [],
"WorkPoints": [
"STOPPER 型式:BNF1605-5RRGT\u002B157LC5(33437272D000)※ﾎﾞｰﾙｽﾌﾟﾗｲﾝが包装されているｼｰﾙに記載",
"ｼﾘｱﾙ№",
"型式確認･ｼﾘｱﾙ№記入",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"To... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立③",
"WorkItems": [
"1. に を挿入しBOLT を仮止め",
"◆2. 1完成品のﾎﾞｰﾙﾈｼﾞ周辺に金ﾆｽを塗布する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "金ﾆｽ塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組込み①",
"WorkItems": [
"◆1. に をBOLT で16箇所で固定する(重量物のためｸﾚｰﾝを使用すること)"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組込み①",
"WorkItems": [
"◆1. に をBOLT で16箇所で固定する(重量物のためｸﾚｰﾝを使用すること)"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"◆1. MOTOR-BRACKET の下面及び左側面以外の外周りの加工面に金ﾆｽを塗装する",
"◆2. BEARING にｸﾞﾘｰｽをいれIﾏｰｸを合わせる",
"3. 2完成品にPLATE をBOLT で締結する"
],
"WorkPoints": [
"･BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞはﾏｰｸを合わせ､MOTOR-BRACKET に挿入する(正面合わせ､... | {
"QualityItem": "金ﾆｽ塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"◆1. MOTOR-BRACKET の下面及び左側面以外の外周りの加工面に金ﾆｽを塗装する",
"◆2. BEARING にｸﾞﾘｰｽをいれIﾏｰｸを合わせる",
"3. 2完成品にPLATE をBOLT で締結する"
],
"WorkPoints": [
"･BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞはﾏｰｸを合わせ､MOTOR-BRACKET に挿入する(正面合わせ､... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の30%~40%",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"3. 2完成品にPLATE をBOLT で締結する"
],
"WorkPoints": [
"挿入時方向に注意する",
"取付け後､隙間を確認(0.01㎜以上)",
"塗布禁止場所(ﾓｰﾀｰ取付け面､ﾌﾚｰﾑ取付け面)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰﾌﾞﾗｹｯﾄ組込み",
"WorkItems": [
"1. のﾎﾞｰﾙﾈｼﾞにSTOPPER を挿入する",
"2. 1完成品に を挿入しBOLT で締結する"
],
"WorkPoints": [
"挿入時ﾋﾟﾝに当てながらﾎﾞｰﾙねじ部がｽﾑｰｽﾞに挿入できること(ﾋﾟﾝとの隙間:0.01㎜以下)",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "10N･m",
"WorkName": "H軸ﾎﾞｰﾙねじ芯出し",
"WorkItems": [
"2. 1完成品のﾎﾞｰﾙねじ取付け部の仮締め部分の本締め6箇所を行う"
],
"WorkPoints": [
"NUT のNUT方向注意",
"WASHER ｶﾗｰ2枚",
"NUT ﾅｯﾄﾄﾙｸ締付後付属品で固定",
"ﾋﾟｰｽ･ｾｯﾄﾋﾞｽ",
"･NUT ﾅｯﾄは挿入方向に注意･ﾄﾙｸ締結後､NUT 付属品で固定する",... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000㎜",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾙねじ芯振れ確認",
"WorkItems": [
"1. のﾎﾞｰﾙﾈｼﾞ先端の芯振れを確認する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "10μm以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000㎜",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾙねじｽﾗｽﾄｶﾞﾀ確認",
"WorkItems": [
"1. のﾎﾞｰﾙねじｽﾗｽﾄ方向のｶﾞﾀを確認する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "ｽﾗｽﾄ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "ｶﾞﾀ5μm以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "2.5N･m以下",
"WorkName": "ﾎﾞｰﾙねじ回転ﾄﾙｸ測定",
"WorkItems": [
"1. のﾎﾞｰﾙねじの回転ﾄﾙｸ値を確認する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "回転ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "2.5N以下",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組付け",
"WorkItems": [
"■1. MOTOR の型式確認とｼﾘｱﾙ№を検査書に記入",
"2. のｺﾈｸﾀｰにLABEL TERMINAL PROCESS ﾏｰｷﾝｸﾞﾀｲ取付け",
"3. にCOUPLING を挿入し､2完成品をBOLT WASHER で締結する"
],
"WorkPoints": [
"P1･EM4210P(6P)･BM4210P(2P)･MM4210P(4P)",
"各... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組付け",
"WorkItems": [
"■1. MOTOR の型式確認とｼﾘｱﾙ№を検査書に記入",
"2. のｺﾈｸﾀｰにLABEL TERMINAL PROCESS ﾏｰｷﾝｸﾞﾀｲ取付け",
"3. にCOUPLING を挿入し､2完成品をBOLT WASHER で締結する"
],
"WorkPoints": [
"P1･EM4210P(6P)･BM4210P(2P)･MM4210P(4P)",
"各... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀｰ原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "H軸原点調整①",
"WorkItems": [
"2. のｶｯﾌﾟﾘﾝｸﾞの下側ﾅｯﾄを締結する",
"1. のモーターコネクターに治具㉖㉗を接続し、駆動部を上下させフレーム後側から㉘原点出しピン（φ6-120㎜）を挿入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具",
"Size": "",
"ToolOther": "FM-3229",
"WorkName": "H軸原点調整①",
"WorkItems": [
"2. のｶｯﾌﾟﾘﾝｸﾞの下側ﾅｯﾄを締結する",
"1. のモーターコネクターに治具㉖㉗を接続し、駆動部を上下させフレーム後側から㉘原点出しピン（φ6-120㎜）を挿入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾃｰﾌﾞﾙX軸用ﾋﾟﾝ",
"Size": "φ6",
"ToolOther": "FM-3467",
"WorkName": "H軸原点調整①",
"WorkItems": [
"2. のｶｯﾌﾟﾘﾝｸﾞの下側ﾅｯﾄを締結する",
"1. のモーターコネクターに治具㉖㉗を接続し、駆動部を上下させフレーム後側から㉘原点出しピン（φ6-120㎜）を挿入する"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3467",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "19㎜",
"ToolOther": "29.4N･m",
"WorkName": "H軸原点調整①",
"WorkItems": [],
"WorkPoints": [
"締付ﾄﾙｸ 29.4N･m"
],
"Tolks": [
"締付ﾄﾙｸ 29.4N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾄﾙｸｽﾊﾟﾅで締付け(19㎜)(右回転で締付け方向です)",
"中央ﾅｯﾄを固... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "29.4N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀｰ原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "H軸原点調整②",
"WorkItems": [],
"WorkPoints": [
"締付ﾄﾙｸ 63.7N･m"
],
"Tolks": [
"締付ﾄﾙｸ 63.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾓｰﾀｰと駆動部が原点にいる事",
"検査表 :ｶｯﾌﾟﾘﾝｸﾞ締結",
... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具",
"Size": "",
"ToolOther": "FM-3229",
"WorkName": "H軸原点調整②",
"WorkItems": [],
"WorkPoints": [
"締付ﾄﾙｸ 63.7N･m"
],
"Tolks": [
"締付ﾄﾙｸ 63.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾓｰﾀｰと駆動部が原点にいる事",
"検査表 :ｶｯﾌﾟﾘﾝｸﾞ締結"
]
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾃｰﾌﾞﾙX軸用ﾋﾟﾝ",
"Size": "φ6",
"ToolOther": "FM-3467",
"WorkName": "H軸原点調整②",
"WorkItems": [],
"WorkPoints": [
"締付ﾄﾙｸ 63.7N･m"
],
"Tolks": [
"締付ﾄﾙｸ 63.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾓｰﾀｰと駆動部が原点にいる事",
"検査表 :ｶｯﾌﾟﾘﾝｸﾞ締結"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3467",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "29㎜",
"ToolOther": "63.7N･m",
"WorkName": "H軸原点調整②",
"WorkItems": [],
"WorkPoints": [
"締付ﾄﾙｸ 63.7N･m"
],
"Tolks": [
"締付ﾄﾙｸ 63.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾓｰﾀｰと駆動部が原点にいる事",
"検査表 :ｶｯﾌﾟﾘﾝｸﾞ締結",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "63.7N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前部ｽｹｰﾙ部組込み",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WWYJ-5300-065"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-065",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100㎜",
"ToolOther": "",
"WorkName": "駆動軸ﾌﾞﾗｹｯﾄにﾌﾟﾚｰﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :H軸ﾌﾞﾗｹｯﾄ平行確認",
"平行度測定位置は赤○部を測定",
"両端L,R点で0.02mm以内",
"WWYJ-5300... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "L点で0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "駆動部ﾌﾚｰﾑにFT4取付け",
"WorkItems": [
"1. にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"駆動部ﾌﾚｰﾑ上面... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "背面部組立①",
"WorkItems": [
"1. BRACKET にLABEL LABEL を貼付けする"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立②",
"WorkItems": [
"1. にMANIFOLD MANIFOLD をBOLT WASHER で締結する",
"2. にJOINT SPACER をBOLT WASHER WASHER BOLT ㉒で締結する",
"3. にSPACER を6本WASHER BOLT で取付ける",
"4. にCABLE-SUPPORT を24個取付ける"
],
"WorkPoints": [
"SPACE... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P1:⑥⑦⑧の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P2:⑥⑦⑧の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P1:⑥⑦⑧の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P2:⑥⑦⑧の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P1ﾘﾚｰ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立③",
"WorkItems": [
"■2. SOCKET にRELAY LAMP を取付ける",
"3. にSOCKET をBOLT WASHER WASHER で固定",
"1. SOCKET RELAY LAMP の型式確認"
],
"WorkPoints": [
"廃棄",
"確実にﾛｯｸすること",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕... | {
"QualityItem": "P2ﾘﾚｰ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [
"3. にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING I/O LOAD BOARD の型式確認を行いｼﾘｱﾙ№を記入する",
"■★2. RING I/O LOAD BOARD の設定を行う"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"... | {
"QualityItem": "P1:⑥の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [
"3. にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING I/O LOAD BOARD の型式確認を行いｼﾘｱﾙ№を記入する",
"■★2. RING I/O LOAD BOARD の設定を行う"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"... | {
"QualityItem": "P1:⑥の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [
"3. にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING I/O LOAD BOARD の型式確認を行いｼﾘｱﾙ№を記入する",
"■★2. RING I/O LOAD BOARD の設定を行う"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"... | {
"QualityItem": "P1:⑥の設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [
"3. にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING I/O LOAD BOARD の型式確認を行いｼﾘｱﾙ№を記入する",
"■★2. RING I/O LOAD BOARD の設定を行う"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"... | {
"QualityItem": "P2:⑥の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [
"3. にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING I/O LOAD BOARD の型式確認を行いｼﾘｱﾙ№を記入する",
"■★2. RING I/O LOAD BOARD の設定を行う"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"... | {
"QualityItem": "P2:⑥の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立④",
"WorkItems": [
"3. にRING I/O LOAD BOARD をBOLT WASHER で固定",
"■★1. RING I/O LOAD BOARD の型式確認を行いｼﾘｱﾙ№を記入する",
"■★2. RING I/O LOAD BOARD の設定を行う"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"... | {
"QualityItem": "P2:⑥の設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-137",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立⑤",
"WorkItems": [
"1. にP1はCABLE CABLE (P2はCABLE CABLE )をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"1B10640",
"1B10630",
"1R30620",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)",
"1B10E40",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立⑥",
"WorkItems": [
"1. にP1はCABLE (P2はCABLE )をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"1B10620",
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)",
"1B10E20",
"P1用=\u003E",
"P2用=\u003E"
],
"To... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "背面部組立⑦",
"WorkItems": [
"1. TUBE TUBE を指定の長さにｶｯﾄする",
"2. にTUBE TUBE を取付ける"
],
"WorkPoints": [
"この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面部組立⑧(OPL3/R3,L4/R4)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨﾙﾀｰｷｯﾄ組立",
"WorkItems": [
"1. SHEET にFILTER をRUBBER-CUSHION で取付ける"
],
"WorkPoints": [
"ｼｰﾄのR処理されている方に取付ける事",
"ｼｰﾄにひび割れがないか確認する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM型式確認",
"WorkItems": [
"■1. PCB-COM の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■安全作業",
"検査表②:1.構成ﾁｪｯｸ"... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-21011",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM型式確認",
"WorkItems": [
"■1. PCB-COM の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■安全作業",
"検査表②:1.構成ﾁｪｯｸ"... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~JP8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定すべてOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-21011",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~JP8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定すべてOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~JP8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定すべてOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り設定されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "30cN･m",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ取付け①",
"WorkItems": [
"1. にSPACER をSCREW WASHER で取付ける",
"2. 1完成品に を載せる"
],
"WorkPoints": [
"ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀのｶﾒﾗI/Fﾎﾞｰﾄﾞｺﾈｸﾀ部に基板を入れてPCI-Eｺﾈｸﾀの勘合を行う",
"勘合の際､各基板に過度のｽﾄﾚｽをかけない様注意する事",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ取付け①",
"WorkItems": [
"1. にSPACER をSCREW WASHER で取付ける",
"2. 1完成品に を載せる"
],
"WorkPoints": [
"ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀのｶﾒﾗI/Fﾎﾞｰﾄﾞｺﾈｸﾀ部に基板を入れてPCI-Eｺﾈｸﾀの勘合を行う",
"勘合の際､各基板に過度のｽﾄﾚｽをかけない様注意する事",
"SPACER の線を下にして... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-21011",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ4.0㎜",
"ToolOther": "10cN･m",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "35cN･m",
"WorkName": "ｶﾒﾗI/Fﾎﾞｰﾄﾞ取付け②",
"WorkItems": [
"1. にSCREW を取付ける",
"2.1完成品をSCREW WASHER で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 35cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "35cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝﾀｰﾚｰﾙ前組立て",
"WorkItems": [
"1. INSULATOR を点線の位置で折る",
"2. RAIL の指定箇所に､1.完成品の上側を引っ掛け､左基準で穴位置を合わせ押し込む"
],
"WorkPoints": [
"不要の為廃棄",
"1.完成品",
"ｶﾁｯというまで確実に取付ける事",
"ｲﾝｼｭﾚｰﾀｰの取付け位置･方向に注意する事"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱﾚｰﾙ前組立て",
"WorkItems": [
"1. INSULATOR を点線の位置で折る",
"2. RAIL の指定箇所に､1.完成品の下側を引っ掛け､左基準で穴位置を合わせ押し込む"
],
"WorkPoints": [
"不要の為廃棄",
"1.完成品",
"ｶﾁｯというまで確実に取付ける事",
"ｲﾝｼｭﾚｰﾀｰの取付け位置･方向に注意する事"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾙ取付け①",
"WorkItems": [
"1. の指定箇所に をｾｯﾄし､ で仮締めする(2箇所)",
"2. 1.完成品の に を面取り部を前面にして切断面から挿入する(上下2箇所)"
],
"WorkPoints": [
"上側",
"下側",
"ﾀﾞﾎﾞに当てつける事",
"ﾀﾞﾎﾞに当てつける事",
"前面",
"ﾚｰﾙの取付方向に注意する事",
"SD-A052... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾙ取付け②",
"WorkItems": [
"1. の指定箇所に をｾｯﾄし､ で仮締めする"
],
"WorkPoints": [
"ﾚｰﾙの取付方向に注意する事",
"ﾀﾞﾎﾞに当てつける事",
"上側",
"中側",
"下側",
"ﾀﾞﾎﾞに当てつける事",
"ﾀﾞﾎﾞに当てつける事",
"ｲﾝｼｭﾚｰﾀｰが下向きに取付ける事",
"SD-A052331-... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付け",
"WorkItems": [
"1. のﾚｰﾙ取付穴の左から3番目に をｾｯﾄし､下から押し込み取付ける(2箇所)",
"2. のﾚｰﾙ取付穴の左から3番目に をｾｯﾄし､上から押し込み取付ける(2箇所)"
],
"WorkPoints": [
"左から3番目",
"下側",
"左から3番目",
"上側"
],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM確認",
"WorkItems": [
"1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｼﾘｱﾙNo. の入力",
"型式確認R22399-G1",
"検査表PCB-COM :1.安全部品受入"... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM仮取付け",
"WorkItems": [
"1. の裏面を手前にする",
"2. のﾚｰﾙ穴と､ の穴位置を合せ､ で仮締めする(6箇所)"
],
"WorkPoints": [
"ｲﾝｼｭﾚｰﾀｰがある事を確認する",
"ﾚｰﾙの右端から4つ目に穴位置を合せる事",
"基板調整の為､仮締めにする事(6箇所)",
"裏面",
"ｲﾝｼｭﾚｰﾀｰが下側にある事を確認",
"S... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部確認",
"WorkItems": [
"■1. の型式を確認し､ｼﾘｱﾙNo.を検査表に記入する",
"■2. 指定箇所に認証ﾏｰｸが記載されている事を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"認証ﾏｰｸの確認",
"ｼﾘｱﾙNo. の入力",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部確認",
"WorkItems": [
"■1. の型式を確認し､ｼﾘｱﾙNo.を検査表に記入する",
"■2. 指定箇所に認証ﾏｰｸが記載されている事を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"認証ﾏｰｸの確認",
"ｼﾘｱﾙNo. の入力",
... | {
"QualityItem": "認証ﾏｰｸ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "認証ﾏｰｸが記載されている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "電源部取付け",
"WorkItems": [
"1. に を で取付ける",
"2. 1完成品に を取付ける"
],
"WorkPoints": [
"取付方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部配線接続",
"WorkItems": [
"1. の電源ﾕﾆｯﾄからのP1､J2を､それぞれ指定箇所に差込む",
"2. 電源配線をｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints": [
"ｶﾁｯと音がするまで確実に差込む事",
"ﾚｰﾙに触れないよう配線の中心を束ねる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ取付け①",
"WorkItems": [
"1. にCOVER かぶせ､SCREW で仮締結する(9箇所)"
],
"WorkPoints": [
"SD-A052331-020,021で本締結",
"配線の挟み込まないよう注意する事",
"COVER のｶﾊﾞｰが内側に来るように取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め①",
"WorkItems": [
"■1. NCIO3 BOARD(MEL) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. の指定箇所に､NCIO3 BOARD(MEL) を挿入しながら､PCB-COMとの差込具合を確認する"
],
"WorkPoints": [
"ここのくぼみ部に基板を差込む事",
"差込位置､方向を間違え無い事",
"ﾌｯｸが確実にかかるか確... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め①",
"WorkItems": [
"■1. NCIO3 BOARD(MEL) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. の指定箇所に､NCIO3 BOARD(MEL) を挿入しながら､PCB-COMとの差込具合を確認する"
],
"WorkPoints": [
"ここのくぼみ部に基板を差込む事",
"差込位置､方向を間違え無い事",
"ﾌｯｸが確実にかかるか確... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め②",
"WorkItems": [
"1. の指定箇所に､ を挿入しながら､PCB-COMとの差込具合を確認する"
],
"WorkPoints": [
"ここのくぼみ部に基板を差込む事",
"無理に押し込ま無い事",
"差込位置､方向を間違え無い事",
"ﾌｯｸが確実にかかるか確認する事",
"矢印部を押しながらﾚﾊﾞｰを上げゆっくり取付ける事"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "PCB-COM締付",
"WorkItems": [
"1. の裏面を手前にする",
"2. 仮固定したPCB-COM基板のﾈｼﾞを本締めする(6箇所)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ｶﾊﾞｰ締付①",
"WorkItems": [
"1. のｶﾊﾞｰとﾚｰﾙを仮固定したﾈｼﾞを､本締めする(10箇所)"
],
"WorkPoints": [
"左側面",
"右側面"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ｶﾊﾞｰ締付②",
"WorkItems": [
"2. 締結確認後､NC/IOﾎﾞｰﾄﾞ､CPUﾎﾞｰﾄﾞを外す",
"1. のｶﾊﾞｰとﾌﾞﾗｹｯﾄを仮固定したﾈｼﾞを､本締めする(4箇所)"
],
"WorkPoints": [
"2つのﾎﾞｰﾄﾞを外す"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線接続",
"WorkItems": [
"1. の裏面を手前にする",
"2. のJ2､P3､CN4を､それぞれ指定箇所に差込む",
"3. J2の配線にCN4の配線を余長分折り曲げてｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints": [
"ｶﾁｯと音がするまで確実に差込む事",
"P3(2ﾋﾟﾝ)のｺﾈｸﾀはJ2(20ﾋﾟﾝ)の内側を通すこと"
],
"Tolks": [],
"Ins... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "FAN取付け",
"WorkItems": [
"1. の指定箇所に､ と を重ね合わせる",
"2. と､重ねた の穴位置を合わせて､ で締結する"
],
"WorkPoints": [
"ﾗﾍﾞﾙが見えるように取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET の爪を の抜き穴に奥まで入れた後､抜きながら倒し､穴位置を合せる事",
"2. BRACKET の穴位置確認後､SCREW で締結する"
],
"WorkPoints": [
"板金に負荷がかからないように注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ｶﾊﾞｰ取付け②",
"WorkItems": [
"1. に を取付け､ で締結する",
"2. FANの配線を接続する"
],
"WorkPoints": [
"配線を挟み込まないように注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨﾙﾀｰｷｯﾄ挿入",
"WorkItems": [
"1. に を差込む"
],
"WorkPoints": [
"ﾗﾊﾞｰｸｯｼｮﾝがﾊﾟﾝﾁ穴に引っ掛かっている事を確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｽﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "出力電圧確認",
"WorkItems": [
"1. のP2ｺﾈｸﾀに㉗を接続する",
"4. ㉖のファンクションスイッチを電圧に合わせる",
"3. の電源をONする",
"2. 電源ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"P... | {
"QualityItem": "出力電圧確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績表",
"StdVal": "11.4~12.6V",
"Method": "ﾃｽﾀｰ",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.