input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P002PLATE取付位置確認",
"WorkItems": [
"3. ｹｰﾌﾞﾙの接続を確認したら㉖の電源をONにする",
"4. ㉖のｽｲｯﾁで上ﾌﾟﾚｰﾄを5回動作させ下限の状態で保持する",
"5. ㉗の上に\u300037.5㎜±0.1mmの治具を載せ測定する",
"6. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
"1)上ﾌﾟﾚｰﾄが下限の状態で、ｼﾘﾝﾀﾞｰ締... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "",
"ToolOther": "3.0N･m",
"WorkName": "P002PLATE取付位置確認",
"WorkItems": [
"1. へﾊﾞﾙﾌﾞｹｰﾌﾞﾙを接続する",
"2. へｾﾝｻｰｹｰﾌﾞﾙを接続する",
"3. ｹｰﾌﾞﾙの接続を確認したら㉖の電源をONにする",
"4. ㉖のｽｲｯﾁで上ﾌﾟﾚｰﾄを5回動作させ下限の状態で保持する",
"5. ㉗の上に\u300037.5㎜±0.1mmの治具を載せ測定する",
"6. ｼﾘﾝﾀﾞｰとｼｬﾌﾄの... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面",
"左側PLATE (長い方)",
"右側PLATE (短い方)... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "60.5±0.05㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDSJ-G002-C06",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4397",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面",
"左側PLATE (長い方)",
"右側PLATE (短い... | {
"QualityItem": "平面度確認",
"ToolManageNo": "FM-4397",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N.m",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面",
"左側PLATE (長い方)",
"右側PLATE (短い方)",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N.m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面",
"左側PLATE (長い方)",
"右側PLATE (短い方)"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面",
"左側PLATE (長い方)",
"右側PLATE (短い方)",
... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "50±0.1㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WDSJ-G002-C06",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-2675",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面",
"左側PLATE (長い方)",
"右側PL... | {
"QualityItem": "出代確認",
"ToolManageNo": "FM-2675",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-4427をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3. を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて ④が基準寸法(60.5±... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDSJ-G002-C06",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-4427をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3. を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて ④が基準寸法(60.5±0.05... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-4427をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3. を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて ④が基準寸法(60.5±0... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-4427",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-4427をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3. を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて ④が基準寸法(60... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4427",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P003,P004ﾌﾟﾚｰﾄ取付調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-4427をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3. を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて ④が基準寸法(60.5±0.05)に入ってい... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "0.001㎜",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付調整",
"WorkItems": [
"2. の平面度調整を行う"
],
"WorkPoints": [
" ③④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
"規格値:2.5±0.01㎜",
" 番を基準として､⑥⑦⑨⑩番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"⑥⑦の高さ : 番を基準に-0.040~-... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "2.5±0.01㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDSJ-G002-C06",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-4427",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付調整",
"WorkItems": [
"2. の平面度調整を行う"
],
"WorkPoints": [
" ③④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
"規格値:2.5±0.01㎜",
" 番を基準として､⑥⑦⑨⑩番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"⑥⑦の高さ : 番を基準に-0.040... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4427",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付調整",
"WorkItems": [
"2. の平面度調整を行う"
],
"WorkPoints": [
" ③④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
"規格値:2.5±0.01㎜",
" 番を基準として､⑥⑦⑨⑩番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"⑥⑦の高さ : 番を基準に-0.040~-0.... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受ﾌﾟﾚｰﾄ搭載面調整治具",
"Size": "",
"ToolOther": "FM-4639",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付調整",
"WorkItems": [
"2. の平面度調整を行う"
],
"WorkPoints": [
" ③④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
"規格値:2.5±0.01㎜",
" 番を基準として､⑥⑦⑨⑩番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"⑥⑦の高さ : 番を基準に-0.040... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4639",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾕﾆｯﾄｼﾘｱﾙｼｰﾙ貼付",
"WorkItems": [
"1. に 製造手配銘板を貼付ける"
],
"WorkPoints": [
"6㎜",
"15㎜",
"貼付面の油脂･ｺﾞﾐ等は除去する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"削除"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:6㎜寸法:15㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "200cN･m",
"WorkName": "ﾊﾟﾝﾁﾝｸﾞﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. PLATE の裏面に㉘をかけ、㉙を塗布する",
"2. ①にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"①のﾌﾛﾝﾄ側の基準ﾋﾟﾝにPLATE を入れ取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo": "",... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞを実施する"
],
"WorkPoints": [
"注意｢③の切替時｣｢A･Bの上下動作時｣隣に同じ作業する作業者がい無い事(勘違いにより反対側を動作させてしまう恐れが有る)",
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:0.5~0.55MPa",
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF安全の為､二人作業は禁... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｴﾗｰ無き事",
"Method": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ",
"RecordMethod": "WDSJ-G002-C06",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する",
"3. 速度調整後､防錆油を塗布する",
"2. のｾﾝｻのI/Oﾁｪｯｸをする"
],
"WorkPoints": [
"ｴｰｼﾞﾝｸﾞ2000回実施後確認する",
" を上下させｾﾝｻを遮光しているか確認する"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "ｽﾋﾟｺﾝ調整",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "・上昇側→全閉より3回転・下降側→全閉より3回転",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する",
"3. 速度調整後､防錆油を塗布する",
"2. のｾﾝｻのI/Oﾁｪｯｸをする",
"1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する",
"3. 速度調整後､防錆油を塗布する",
"2. のｾﾝｻのI/Oﾁｪｯｸをする"
],
"WorkPoints": [
"... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "【上昇時】表示値1.1s±0.02s【下降時】表示値0.9s±0.02s",
"Method": "目視",
"RecordMethod": "WDSJ-G002-C06",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する",
"3. 速度調整後､防錆油を塗布する",
"2. のｾﾝｻのI/Oﾁｪｯｸをする",
"1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する",
"3. 速度調整後､防錆油を塗布する",
"2. のｾﾝｻのI/Oﾁｪｯｸをする"
],
"WorkPoints": [
"... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "【上昇時】表示値1.1s±0.02s【下降時】表示値0.9s±0.02s",
"Method": "目視",
"RecordMethod": "WDSJ-G002-C06",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する",
"3. 速度調整後､防錆油を塗布する",
"2. のｾﾝｻのI/Oﾁｪｯｸをする",
"1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する",
"3. 速度調整後､防錆油を塗布する",
"2. のｾﾝｻのI/Oﾁｪｯｸをする"
],
"WorkPoints": [
"... | {
"QualityItem": "IO確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "検査指示通り動作する事",
"Method": "目視",
"RecordMethod": "WDSJ-G002-C06",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "払出し準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "-",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ移載治具",
"Size": "",
"ToolOther": "FM-4497",
"WorkName": "払出し準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "-",
"ToolManageNo": "FM-4497",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞｰ組立台",
"Size": "",
"ToolOther": "FM-4396",
"WorkName": "払出し準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "部材確認",
"ToolManageNo": "FM-4396",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付・払出し準備",
"WorkItems": [],
"WorkPoints": [
"11㎜",
"75㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:11㎜寸法:75㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾌﾞｯｼｭｸﾞﾘｰｽｱｯﾌﾟ",
"WorkItems": [
"2. 8ｾｯﾄ行う",
"◆1. LINEAR-BUSH にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"LINEAR-BUSH を開封し､油を拭取る事",
"LINEAR-BUSH の表面にｸﾞﾘｰｽを塗布する事",
"ｺﾞﾐなどが付着しないように注意する事",
"ﾎﾞｰﾙ部を上下させながら埋まる程度に塗布する余りは除去す... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布80㎜,小豆粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-①",
"WorkItems": [
"1. ㉖の本体エアー配管を工場エアー配管に接続する",
"3. ㉖の圧力計を確認または調整する",
"2. ㉖のエアーバルブを開にする"
],
"WorkPoints": [
"設定圧力:0.50Mpa±0.05",
"ﾊﾝﾄﾞﾙ",
"ﾛｯｸﾅｯﾄ",
"圧力調整はロックナットを㉗で緩め、ハンド... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "0.50Mpa±0.05",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙはかり",
"Size": "",
"ToolOther": "EK-3000i",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-②",
"WorkItems": [
"1. LINEAR-BUSH を開封し油を拭き取る(黄色部)",
"2. ㉖の電源を投入する",
"3. 1完成品を㉖に乗せ、ゼロ設定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-③",
"WorkItems": [
"◆1. を㉖にセットし、内側ボール内にグリースを塗布する"
],
"WorkPoints": [
" を素手で触ら無い事",
"Hｶｯﾄ面をｶﾞｲﾄﾞに合わせる",
"ｽﾄｯﾊﾟｰに当付ける",
"2秒以上ﾎﾞﾀﾝを長押しｸﾞﾘｰｽを塗布する(ｼﾘﾝﾀﾞｰが動かなくなるまで)",
"ｸﾞﾘｰｽが塗布される... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り塗布出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙはかり",
"Size": "",
"ToolOther": "EK-3000i",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-④",
"WorkItems": [
"1. を㉖に乗せグリス塗布量を計測する",
"◆2. 1完成品の表面全体に㉗グリースを塗布する（黄色部）"
],
"WorkPoints": [
"ｺﾞﾐ等が付着してい無い事を確認する事",
" を素手で触ら無い事"
],
"Tolks": [],
"InspectionNo": ""... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "5g~7g",
"Method": "ﾃﾞｼﾞﾀﾙはかり",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-④",
"WorkItems": [
"1. を㉖に乗せグリス塗布量を計測する",
"◆2. 1完成品の表面全体に㉗グリースを塗布する（黄色部）"
],
"WorkPoints": [
"ｺﾞﾐ等が付着してい無い事を確認する事",
"特にﾕﾆｯﾄ取付面にｺﾞﾐ等が付着してい無い事",
" を素手で触ら無い事"
],
"Tolks": [],
"I... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄﾋﾟﾝ圧入①",
"WorkItems": [
"1. PLATE に油砥石をかける(両面､左右面)",
"2. PLATE にPIN を圧入する",
"3. 2ｾｯﾄ組立て"
],
"WorkPoints": [
"出代: 3.0±0.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words":... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄﾋﾟﾝ圧入②",
"WorkItems": [
"1. にPIN を圧入する",
"2. 2ｾｯﾄ組立て"
],
"WorkPoints": [
"出代: 3.0±0.5㎜",
"PIN は面取り側から圧入する事",
"PIN の圧入位置と の向きに注意する事",
" の向き",
"PIN の圧入位置",
"ｻﾞｸﾞﾘ面が上面"
],
"Tolks": ... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄｼｬﾌﾄ取付け(右実装部)",
"WorkItems": [
"1. の両面に防錆油を塗布する",
"2. にSHAFT をBOLT で仮取付け"
],
"WorkPoints": [
"締付:SD-A011666-030で締付",
" の向き",
"SHAFT の取付位置(ｻﾞｸﾞﾘ穴)"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄｼｬﾌﾄ取付け(左実装部)",
"WorkItems": [
"1. の両面に防錆油を塗布する",
"2. にSHAFT をBOLT で仮取付け"
],
"WorkPoints": [
"締付:SD-A011666-049で締付",
" の向き",
"SHAFT の取付位置(ｻﾞｸﾞﾘ穴)"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰﾅｯﾄ締付治具",
"Size": "",
"ToolOther": "FM-2984",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞﾌﾟﾚｰﾄ取付け",
"WorkItems": [
"1. CYLINDER の付属ﾌﾟﾚｰﾄ(平面側)に油砥石をかけ防錆油を塗布する",
"2. CYLINDER の付属ﾌﾟﾚｰﾄを固定する",
"3. 4ｾｯﾄ組立て"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2984",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｼﾞｮｲﾝﾄ取付け",
"WorkItems": [
"1. にJOINT を取付ける",
"2. 4ｾｯﾄ組立て"
],
"WorkPoints": [
"ｼｰﾙﾃｰﾌﾟのｶｽはｽｹｰﾙ等で取り除く事",
"ねじ部が3~4mmになるまで締め込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3~4㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞﾅｯﾄ取付け",
"WorkItems": [
"1. CYL-NUT に油砥石をかける",
"3. にCYL-NUT を取付ける",
"4. 4ｾｯﾄ組立てる",
"◆2. CYL-NUT にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"上面部に油砥石をかける",
"上面部にｸﾞﾘｰｽを塗布する",
"ねじ部の終わりまで入れておく"
],
"Tolks"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾊﾞﾙﾌﾞ組立て",
"WorkItems": [
"1. VALVE のｼﾞｮｲﾝﾄ･ﾏﾌﾗｰを増し締めする",
"2. VALVE にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｽﾋﾟｺﾝ組立て",
"WorkItems": [
"5. SOLENOID-VALVE にJOINT JOINT を取付け",
"6. SOLENOID-VALVE のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰを調整し､仮ﾛｯｸする",
"4. SOLENOID-VALVE にJOINT を取付け"
],
"WorkPoints": [
"SPEED-CONTROLLER とSOLENOID-VALVE の隙間3㎜程度",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3~4㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｾﾝｻｰ組立て",
"WorkItems": [
"1. PLATE に防錆油を塗布する",
"2. PLATE にSENSOR SPACER をBOLT WASHER WASHER で取付け",
"3. 2ｾｯﾄ組立て"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ高さ調整冶具",
"Size": "",
"ToolOther": "FM-4961",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ組立て",
"WorkItems": [
"1. BOLT の上面に油砥石をかける",
"2. BOLT にNUT を挿入する",
"1. BOLT の上面に油砥石をかける",
"2. BOLT にNUT を挿入する"
],
"WorkPoints": [
"ﾊﾞﾘ､ｶｴﾘ等無いことを確認する",
"挿入後､10回転(約8mm程)挿入すること",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4961",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ組立て",
"WorkItems": [
"1. BOLT の上面に油砥石をかける",
"2. BOLT にNUT を挿入する"
],
"WorkPoints": [
"ﾊﾞﾘ､ｶｴﾘ等無いことを確認する",
"挿入後､10回転(約8mm程)挿入すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "8±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ組立て",
"WorkItems": [
"1. BLOCK にPIN を圧入する",
"2. 4ｾｯﾄ組立て"
],
"WorkPoints": [
"ﾋﾟﾝ出代:7mm",
"ﾋﾟﾝの圧入方向に注意する事",
"ﾋﾟﾝ穴の底面まで圧入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "7.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟ部組立て①",
"WorkItems": [
"2. BRACKET にBEARING SPACER をBOLT で取付け",
"3. 完成品にBOLT を取付け",
"4. 4ｾｯﾄ組立てる",
"◆1. BRACKET BRACKET GUIDE SPRING にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"両端に塗布する",
"反対の内側にも同様に塗布する",
"反対の... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｸﾗﾝﾌﾟ部組立て①",
"WorkItems": [
"3. 完成品にBOLT を取付け",
"4. 4ｾｯﾄ組立てる"
],
"WorkPoints": [
"両端に塗布する",
"2面に塗布する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｸﾗﾝﾌﾟ部組立て②",
"WorkItems": [
"1. に をBOLT WASHER WASHER で取付け",
"2. を入れて､BOLT NUT を取付け",
"3. 4ｾｯﾄ組立て",
"1. に をBOLT WASHER WASHER で取付け",
"2. を入れて､BOLT NUT を取付け",
"3. 4ｾｯﾄ組立て"
],
"WorkPoints"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟ部組立て②",
"WorkItems": [
"1. に をBOLT WASHER WASHER で取付け",
"2. を入れて､BOLT NUT を取付け",
"3. 4ｾｯﾄ組立て"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FT-4の取付け(右実装部)",
"WorkItems": [
"1. PLATE に油砥石をかける",
"2. PLATE に防錆油を塗布する",
"3. PLATE にCABLE-SUPPORT を挿入しｲﾝｼｭﾛｯｸを通す"
],
"WorkPoints": [
"各面にかけ､ﾊﾞﾘ､ｶｴﾘ等を取除く"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FT-4の取付け(左実装部)",
"WorkItems": [
"1. PLATE に油砥石をかける",
"2. PLATE に防錆油を塗布する",
"3. PLATE にCABLE-SUPPORT を挿入し､ｲﾝｼｭﾛｯｸを通す"
],
"WorkPoints": [
"各面にかけ､ﾊﾞﾘ､ｶｴﾘ等を取除く"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰの取付け",
"WorkItems": [
"2. SPACER に をWASHER BOLT で仮取付け",
"3. にSPACER をWASHER BOLT で取付け",
"4. SPACER に をWASHER BOLT で仮取付け",
"1. にSPACER をWASHER BOLT で取付け",
"2. SPACER に をWASHER BOLT で仮取付け",
"3... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾘﾆｱﾌﾞｯｼｭ取付け",
"WorkItems": [
"1. に をBOLT で取付け",
"2. に をBOLT で取付け"
],
"WorkPoints": [
" のｻﾞｸﾞﾘ穴ｾﾝﾀｰで取付ける事",
" のｻﾞｸﾞﾘ穴ｾﾝﾀｰで取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "組立治具取付け(右実装部)",
"WorkItems": [
"1. を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"第1実装部と第2実装部では組立て治具取付け位置が前後逆になる為､注意する事",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締付け",
"･ﾘﾆｱﾌﾞｯｼｭの幅の狭い方をPINに押し当てて取付け",
"ｼｯｸﾈｽﾃｰ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ組立台",
"Size": "",
"ToolOther": "FM-4850",
"WorkName": "組立治具取付け(右実装部)",
"WorkItems": [
"1. を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"第1実装部と第2実装部では組立て治具取付け位置が前後逆になる為､注意する事",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締付け",
"･ﾘﾆｱﾌﾞｯｼｭの幅の狭い方をPINに押し当てて取付け",
"ｼｯｸﾈｽ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4850",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "組立治具取付け(右実装部)",
"WorkItems": [
"1. を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"第1実装部と第2実装部では組立て治具取付け位置が前後逆になる為､注意する事",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締付け",
"･ﾘﾆｱﾌﾞｯｼｭの幅の狭い方をPINに押し当てて取付け",
"ｼｯｸﾈｽﾃ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾊﾞﾙﾌﾞ・ｽﾋﾟｺﾝ取付け(右実装部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｼﾞｮｲﾝﾄ取付け(右実装部)",
"WorkItems": [
"1. にJOINT SPACER をBOLT WASHER WASHER で取付け",
"2. にJOINT をBOLT WASHER WASHER で取付け",
"1. にJOINT SPACER をBOLT WASHER WASHER で取付け",
"2. にJOINT をBOLT WASHER WASHER で取付け"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻ取付け(右実装部)",
"WorkItems": [
"1. に WASHER をBOLT WASHER で取付け"
],
"WorkPoints": [
"位置決めについてはﾄﾞｸﾞ取付時の為､仮固定",
"締付:SD-011666-033にて締付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "配管引き回①(右実装部)",
"WorkItems": [
"1. TUBE を各寸法にｶｯﾄする",
"2. にTUBE を引き回す",
"3. にTUBE を引き回す",
"4. にTUBE を引き回す"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰB",
"ｼﾘﾝﾀﾞｰB",
"Aの配管をｼﾘﾝﾀﾞｰ(下)とTｼﾞｮｲﾝﾄ(左下)へ繋ぐ",
"Bの配管をｼﾘﾝ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回②(右実装部)",
"WorkItems": [
"1. にTUBE を引き回す",
"2. にTUBE を引き回す",
"3. にTUBE を引き回す",
"4. にTUBE を引き回す"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰA",
"ｼﾘﾝﾀﾞｰA",
"Dの配管をｼﾘﾝﾀﾞｰA(下)とTｼﾞｮｲﾝﾄ(中下)へ繋ぐ",
"Eの配管をｼﾘﾝﾀﾞｰA(上)とT... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回③(右実装部)",
"WorkItems": [
"1. にTUBE を引き回す",
"4. にTUBE を引き回す",
"3. にTUBE を引き回す",
"2. にTUBE を引き回す"
],
"WorkPoints": [
"Hの配管をﾊﾞﾙﾌﾞ(左)とTｼﾞｮｲﾝﾄ(右下)へ繋ぐ",
"Iの配管をTｼﾞｮｲﾝﾄ(右)とｽﾋﾟｺﾝ(右上)へ繋ぐ",
"Jの配管をｽﾋﾟｺﾝ(右下)... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回④(右実装部)",
"WorkItems": [
"1. の配管を㉖で縛る"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞのｽﾋﾟｺﾝとｼﾞｮｲﾝﾄが図の向きになるように引き回すこと事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回⑤(右実装部)",
"WorkItems": [
"1. の シリンダー部のエアー配管を㉖で縛る",
"2. スピコンのジョイント部分を㉗で縛る（傾き防止の為）"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸの向きに注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄの取付け(右実装部)",
"WorkItems": [
"1. に を乗せる"
],
"WorkPoints": [
"乗せる前に4本のｼｬﾌﾄが動く程度に仮止めされているか確認する",
"こじれるとﾎﾞｰﾙｽﾌﾟﾗｲﾝを破損するので注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄの取付け(右実装部)",
"WorkItems": [
"1. に を乗せる"
],
"WorkPoints": [
"乗せる前に4本のｼｬﾌﾄが動く程度に仮止めされているか確認する",
"こじれるとﾎﾞｰﾙｽﾌﾟﾗｲﾝを破損するので注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示場所が干渉してい無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｬﾌﾄHｶｯﾄ方向合わせ治具",
"Size": "",
"ToolOther": "FM-4956",
"WorkName": "上ﾌﾟﾚｰﾄ位置決め(右実装部)",
"WorkItems": [
"1. のｼｬﾌﾄにWASHER をBOLT で取付け",
"2. 組立台に㉘を取付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4956",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4828",
"WorkName": "上ﾌﾟﾚｰﾄ位置決め(右実装部)",
"WorkItems": [
"1. のｼｬﾌﾄにWASHER をBOLT で取付け",
"2. 組立台に㉘を取付け",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4828",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "上ﾌﾟﾚｰﾄ位置決め(右実装部)",
"WorkItems": [
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(0.05㎜以下)",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｼｯｸﾈ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G0002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "上ﾌﾟﾚｰﾄ位置決め(右実装部)",
"WorkItems": [
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(0.05㎜以下)",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｼｯｸﾈｽ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾁｪｯｶｰ前準備(右実装部)",
"WorkItems": [
"1. ㉖の各コネクターを に取付ける"
],
"WorkPoints": [
"AUTO動作",
"MANUAL動作",
"ｴｱｰ配管は後ほど挿入する為､繋が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(右実装部)",
"WorkItems": [
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する",
"1. CYL-NUT に油砥石をかける"
],
"WorkPoints": [
"芯出し調整時にはｴｱｰを... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(右実装部)",
"WorkItems": [
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"5. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞ寸法の位置決め後､ﾛｯｸする",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する",
"1. CYL... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞ位置調整治具",
"Size": "",
"ToolOther": "FM-2982",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(右実装部)",
"WorkItems": [
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する",
"1. CYL-NUT に油砥石をかける"
],
"WorkPoints": [
"芯出し調整時には... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2982",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(右実装部)",
"WorkItems": [],
"WorkPoints": [
"下降ｽｲｯﾁ"
],
"Tolks": [
"締付ﾄﾙｸ 30.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WASHER を取付けｸﾞﾘｰｽをなじませる",
"WASHER の上にも米粒大を塗... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "7.50±0.05㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(右実装部)",
"WorkItems": [
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"5. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞ寸法の位置決め後､ﾛｯｸする",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する",
"1. CYL-NUT に油砥石をかける",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:8",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "36㎜",
"ToolOther": "30.0N･m",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(右実装部)",
"WorkItems": [],
"WorkPoints": [
"下降ｽｲｯﾁ"
],
"Tolks": [
"締付ﾄﾙｸ 30.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WASHER を取付けｸﾞﾘｰｽをなじませる",
"WASHER ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞｸﾞ取付け調整(右実装部)",
"WorkItems": [
"1. DOG に防錆油を塗布する",
"2. にDOG をBOLT WASHER で取付け",
"3. ｾﾝｻ位置調整後､Aを締付け"
],
"WorkPoints": [
"上ﾌﾟﾚｰﾄを上昇させてから取付け",
"ｼﾘﾝﾀﾞｰを上下させﾄﾞｸﾞとｾﾝｻｰが接触しないように調整する"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾄﾞｸﾞ取付け調整(右実装部)",
"WorkItems": [
"1. DOG に防錆油を塗布する",
"2. にDOG をBOLT WASHER で取付け",
"3. ｾﾝｻ位置調整後､Aを締付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させﾄﾞｸﾞとｾﾝｻｰが接触しないように調整する",
"ｾﾝｻｰの左右はｾﾝﾀﾞｰ奥行きは2/3を目安に取付け",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-035で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "出代:48.5㎜±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-035で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:110.5±0.05㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-035で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける",
"2. にPLATE PLATE をBOLT で仮取付け",
"3. PLATE PLATE の取付高さ調整及び平面度を測定する"
],
"WorkPoints": [
"表裏面と上面にかける",
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4828",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-035で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4828",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "75.5㎜",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(右実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-035で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "75.5㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"規格:0.05mm",
"最終確認は一度上下動作させ測定の事",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "平面度0.02㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"規格:0.05mm",
"最終確認は一度上下動作させ測定の事",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"ﾌ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"規格:0.05mm",
"最終確認は一度上下動作させ測定の事",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"規格:0.05mm",
"最終確認は一度上下動作させ測定の事",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(右実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"規格:0.05mm",
"最終確認は一度上下動作させ測定の事",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"ﾌﾟﾚｰﾄ端面... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ:治具を... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ:治具を... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ:... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ:治具... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄ搭載面調整治具",
"Size": "",
"ToolOther": "FM-4639",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(右実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整:±0.025㎜以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ:治具を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の高さ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4639",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(右実装部)",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
" ､ は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(右実装部)",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
" ､ は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(右実装部)",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
" ､ は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.