input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(右実装部)",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際はｳｪｲﾄ治具を取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整､... | {
"QualityItem": "遮光確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "LEDが消灯する事",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(右実装部)",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際はｳｪｲﾄ治具を取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整､... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(右実装部)",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際はｳｪｲﾄ治具を取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整､... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(右実装部)",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. ｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際はｳｪｲﾄ治具を取付けて実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "組立治具取付け(左実装部)",
"WorkItems": [
"1. を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"右実装部と左実装部では組立治具取付け位置が前後逆になる",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締め付け",
"ﾘﾆｱﾌﾞｯｼｭの狭いほうをPINに押し当てて取付け",
"ｼｯｸﾈｽﾃｰﾌﾟ(0.05㎜)で隙... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ組立台",
"Size": "",
"ToolOther": "FM-4850",
"WorkName": "組立治具取付け(左実装部)",
"WorkItems": [
"1. を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"右実装部と左実装部では組立治具取付け位置が前後逆になる",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締め付け",
"ﾘﾆｱﾌﾞｯｼｭの狭いほうをPINに押し当てて取付け",
"ｼｯｸﾈｽﾃｰﾌﾟ(0.05㎜)... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4850",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "組立治具取付け(左実装部)",
"WorkItems": [
"1. を組立治具にBOLT WASHER で取付け"
],
"WorkPoints": [
"右実装部と左実装部では組立治具取付け位置が前後逆になる",
"下ﾌﾟﾚｰﾄと位置決めPINに隙間無い事",
"18箇所締め付け",
"ﾘﾆｱﾌﾞｯｼｭの狭いほうをPINに押し当てて取付け",
"ｼｯｸﾈｽﾃｰﾌﾟ(0.05㎜)で... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾊﾞﾙﾌﾞ・ｽﾋﾟｺﾝ取付け(左実装部)",
"WorkItems": [
"1. に をBOLT WASHER で取付け",
"1. に をBOLT WASHER で取付け"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｼﾞｮｲﾝﾄ取付け(左実装部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻ取付け(左実装部)",
"WorkItems": [
"1. に WASHER をBOLT WASHER で取付け"
],
"WorkPoints": [
"位置決めについてはﾄﾞｸﾞ取付け時の為､仮固定",
"締付:SD-011666-052にて締付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "配管引き回①(左実装部)",
"WorkItems": [
"1. TUBE を各寸法にｶｯﾄする",
"2. にTUBE を引き回す",
"3. にTUBE を引き回す"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰB",
"ｼﾘﾝﾀﾞｰA",
"Aの配管をｼﾘﾝﾀﾞｰB(下)とTｼﾞｮｲﾝﾄ(右下)へ繋ぐ",
"Bの配管をﾊﾞﾙﾌﾞ(左)とTｼﾞｮｲﾝﾄ(左下)へ繋ぐ",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回②(左実装部)",
"WorkItems": [
"1. にTUBE を引き回す",
"2. にTUBE を引き回す",
"3. にTUBE を引き回す",
"4. にTUBE を引き回す"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰB",
"ｼﾘﾝﾀﾞｰA",
"Dの配管をｼﾘﾝﾀﾞｰB(上)とTｼﾞｮｲﾝﾄ(右中)へ繋ぐ",
"Eの配管をｽﾋﾟｺﾝ(右下)とTｼ... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回③(左実装部)",
"WorkItems": [
"1. にTUBE を引き回す",
"2. にTUBE を引き回す"
],
"WorkPoints": [
"Iの配管をTｼﾞｮｲﾝﾄ(右上)とﾊﾞﾙﾌﾞ(右)へ繋ぐ",
"Jの配管をTｼﾞｮｲﾝﾄ(中上)とｽﾋﾟｺﾝ(左下)へ繋ぐ",
"Kの配管をｽﾋﾟｺﾝ(左上)とTｼﾞｮｲﾝﾄ(左上)へ繋ぐ"
],
"Tolks": [],
"Insp... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回④(左実装部)",
"WorkItems": [
"1. の各配管を㉖で縛る"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管引き回⑤(第2実装部)",
"WorkItems": [
"1. の シリンダー部のエアー配管を㉖で縛る",
"2. スピコンのジョイント部分を㉗で縛る（傾き防止の為）"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"裏側",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞ... | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ組立台",
"Size": "",
"ToolOther": "FM-4850",
"WorkName": "上ﾌﾟﾚｰﾄの取付(左実装部)",
"WorkItems": [
"1. に を乗せる"
],
"WorkPoints": [
"乗せる前に4本のｼｬﾌﾄが動く程度に仮止めされているか確認する",
"こじれるとﾎﾞｰﾙｽﾌﾟﾗｲﾝを破損するので注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4850",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄの取付(左実装部)",
"WorkItems": [
"1. に を乗せる"
],
"WorkPoints": [
"乗せる前に4本のｼｬﾌﾄが動く程度に仮止めされているか確認する",
"こじれるとﾎﾞｰﾙｽﾌﾟﾗｲﾝを破損するので注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示場所が干渉してい無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ組立台",
"Size": "",
"ToolOther": "FM-4850",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4850",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(0... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙間が無い事(0.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｬﾌﾄHｶｯﾄ方向合わせ治具",
"Size": "",
"ToolOther": "FM-4956",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
"上面ﾌﾟﾚｰﾄを上下させてこじれがないか確認すること",
"ｼｬﾌﾄのM6ﾎﾞﾙﾄを締結する事(4本)",
"治具とﾌﾟﾚｰﾄに隙... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4956",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4828",
"WorkName": "上ﾌﾟﾚｰﾄの位置決め(左実装部)",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け",
"1. にPLATE をBOLT で取付ける",
"3. 上面ﾌﾟﾚｰﾄを治具に押し当て締付ける",
"2. 組立台に㉜を取付け"
],
"WorkPoints": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4828",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾁｪｯｶｰ前準備(左実装部)",
"WorkItems": [
"1. ㉖の各コネクターを に取付ける"
],
"WorkPoints": [
"AUTO動作",
"MANUAL動作",
"ｴｱｰ配管は後ほど挿入する為､繋が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する"
],
"WorkPoints": [
"芯出し調整時にはｴｱｰを入れ無い事",
"0.5~0.505MPaに設... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [
"1. CYL-NUT に油砥石をかける",
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"5. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞ寸法の位置決め後､ﾛｯｸする",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞ位置調整治具",
"Size": "",
"ToolOther": "FM-2982",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する"
],
"WorkPoints": [
"芯出し調整時にはｴｱｰを入れ無い事",
"0.5~0.505M... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2982",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [],
"WorkPoints": [
"㉚㉝でロックする"
],
"Tolks": [
"締付ﾄﾙｸ 30.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WASHER を取付けｸﾞﾘｰｽをなじませる",
"WASHER の上にも米粒大... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "7.50±0.05㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [
"1. CYL-NUT に油砥石をかける",
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"5. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞ寸法の位置決め後､ﾛｯｸする",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:8",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "36㎜",
"ToolOther": "30.0N･m",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結(左実装部)",
"WorkItems": [],
"WorkPoints": [
"㉚㉝でロックする"
],
"Tolks": [
"締付ﾄﾙｸ 30.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WASHER を取付けｸﾞﾘｰｽをなじませる",
"WASHE... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞｸﾞ取付け調整(左実装部)",
"WorkItems": [
"1. DOG に防錆油を塗布する",
"2. にDOG をBOLT WASHER で取付け",
"3. ｾﾝｻ位置調整後､Aを締付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させﾄﾞｸﾞとｾﾝｻｰが接触しないように調整する"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾄﾞｸﾞ取付け調整(左実装部)",
"WorkItems": [
"1. DOG に防錆油を塗布する",
"2. にDOG をBOLT WASHER で取付け",
"3. ｾﾝｻ位置調整後､Aを締付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させﾄﾞｸﾞとｾﾝｻｰが接触しないように調整する",
"ｾﾝｻｰの左右はｾﾝﾀﾞｰ奥行きは2/3を目安に取付け"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-054で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "出代:48.5㎜±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-054で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:110.5㎜±0.05㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-054で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける",
"2. にPLATE PLATE をBOLT で仮取付け",
"3. PLATE PLATE の取付高さ調整及び平面度を測定する"
],
"WorkPoints": [
"表裏面と上面にかける",
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4828",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-054で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4828",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "75.5㎜",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け(左実装部)",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける"
],
"WorkPoints": [
"表裏面と上面にかける",
"締付:SD-A011666-054で締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "75.5㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "平面度0.02㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
"規... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整(左実装部)",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を確認する",
"1. 組立台に㉙を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から治具端面まで4㎜で取付け",
"ホルダーと㉙に隙間が無いこと",
" ,③,④⑥は調整不可(差が大きい場合は治具を確認する)",
"調整方法",
"規格:0.02... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整: を基準に平面度0.05mm以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ: を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整: を基準に平面度0.05mm以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ: を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳の... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整: を基準に平面度0.05mm以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ: を基準に-0.04~-0.09mm",
"⑨､⑩､... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整: を基準に平面度0.05mm以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ: を基準に-0.04~-0.09mm",
"⑨､⑩､⑲､⑳... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄ搭載面調整治具",
"Size": "",
"ToolOther": "FM-4639",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整(左実装部)",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を取付け",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ､④､⑤､⑧番のﾎﾞﾙﾄを治具基準に調整: を基準に平面度0.05mm以内",
" ､③､⑥､⑦､⑪､⑫､⑬､⑭､⑮､⑯､⑰､⑱の高さ: を基準に-0.04~-0.09mm",
"⑨､⑩､... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4639",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(左実装部)",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
" ､ は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(左実装部)",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
" ､ は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け(左実装部)",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと",
" ､ は位置決めPINに押し当てて取付け"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(左実装部)",
"WorkItems": [
"1. のｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. のｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際はｳｪｲﾄ治具を取付けて実施する",
"ｽﾋﾟｰﾄ... | {
"QualityItem": "遮光確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "LEDが消灯する事",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(左実装部)",
"WorkItems": [
"1. のｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. のｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際はｳｪｲﾄ治具を取付けて実施する",
"ｽﾋﾟｰﾄ... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(左実装部)",
"WorkItems": [
"1. のｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"1. のｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際はｳｪｲﾄ治具を取付けて実施する",
"ｽﾋﾟｰﾄ... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整(左実装部)",
"WorkItems": [
"1. のｾﾝｻｰ部の遮光を確認する",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際はｳｪｲﾄ治具を取付けて実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞを実施する｡",
"1. 、 に㉖のコネクタ、エアー配管を接続する"
],
"WorkPoints": [
"注意｢③の切替時｣｢A･Bの上下動作時｣隣に同じく作業する作業者がい無い事(勘違いにより反対側を動作させてしまう恐れが有る)",
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:500~505kPa",
... | {
"QualityItem": "動作回数確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2000回",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞを実施する｡",
"1. 、 に㉖のコネクタ、エアー配管を接続する"
],
"WorkPoints": [
"注意｢③の切替時｣｢A･Bの上下動作時｣隣に同じく作業する作業者がい無い事(勘違いにより反対側を動作させてしまう恐れが有る)",
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:500~505kPa",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "最終確認",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"3. ｴｰｼﾞﾝｸﾞ完了後､再度ｽﾋﾟｰﾄﾞ調整を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
" 、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める 、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確認し\u30... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "最終確認",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"3. ｴｰｼﾞﾝｸﾞ完了後､再度ｽﾋﾟｰﾄﾞ調整を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
" 、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める 、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確認し\u30... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.30~1.40S上昇時:0.49~0.64S下降時:1.20~1.35S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C08",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "最終確認",
"WorkItems": [],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰ部のﾎﾞﾙﾄを緩めて調整する"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "最終確認",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"3. ｴｰｼﾞﾝｸﾞ完了後､再度ｽﾋﾟｰﾄﾞ調整を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
" 、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める 、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確認し\u... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付冶具",
"Size": "",
"ToolOther": "FM-4919",
"WorkName": "銘板貼付(右実装部)",
"WorkItems": [
"1. にLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"右実装部",
"22㎜",
"85㎜",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-4919",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付(右実装部)",
"WorkItems": [
"1. にLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"右実装部",
"22㎜",
"85㎜",
"75㎜"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付冶具",
"Size": "",
"ToolOther": "FM-4919",
"WorkName": "銘板貼付(左実装部)",
"WorkItems": [
"1. の貼付け面に㉖で拭取りLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"左実装部",
"22㎜",
"1... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-4919",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付(左実装部)",
"WorkItems": [
"1. の貼付け面に㉖で拭取りLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"左実装部",
"22㎜",
"102㎜",... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ移載治具",
"Size": "",
"ToolOther": "FM-4852",
"WorkName": "払い出し準備",
"WorkItems": [
"1. 、 に㉗を治具専用ボルトで取付ける"
],
"WorkPoints": [
"下ﾌﾟﾚｰﾄにﾎﾞﾙﾄ4箇所で取付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4852",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾋﾟﾝ圧入",
"WorkItems": [
"2. PLATE の裏面にPIN PIN を圧入する",
"2. PLATE にPIN PIN を圧入する",
"2. PLATE の裏面にPIN PIN を圧入する",
"2. PLATE にPIN PIN を圧入する"
],
"WorkPoints": [
"表面(座繰り穴面)",
"ﾋﾟﾝ圧入箇所",
"表面(座繰り穴面)",
... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜出代:23.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "圧入治具",
"Size": "",
"ToolOther": "FM-2386",
"WorkName": "ﾋﾟﾝ圧入",
"WorkItems": [
"2. PLATE の裏面にPIN PIN を圧入する",
"2. PLATE にPIN PIN を圧入する",
"1. PLATE に表裏面、上下左右の側面に㉙で砥石かけ、㉚で拭取る"
],
"WorkPoints": [
"出代:23㎜",
"出代:3㎜",
"裏面",
"出代:3㎜",
"作業終了後､防錆処理を行なう",
... | {
"QualityItem": "圧入確認",
"ToolManageNo": "FM-2386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "圧入治具",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "支柱組立て",
"WorkItems": [
"1. SPACER に㉙砥石かけ、SCREW を締付ける"
],
"WorkPoints": [
"奥まで締付ける",
"SPACER の先端両側面に砥石をかける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"4~5mm",
"ｾｯﾄﾋ... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.0~5.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "4N･m",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰ組立て",
"WorkItems": [
"2. CYLINDER にJOINT を取付ける",
"1. CYLINDER のﾌﾞﾗｹｯﾄの裏面に30をかけ､全体を32を塗布し組立てる"
],
"WorkPoints": [
"ｼｬﾌﾄについている標準ﾅｯﾄは廃棄のこと",
"ﾀｯﾌﾟ面",
"Dｶｯﾄとﾌﾟﾚｰﾄが平行になること",
"ｼﾞｮｲﾝﾄ取付けﾀｯﾌﾟの位置... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "4N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰﾅｯﾄ締付治具",
"Size": "",
"ToolOther": "FM-2984",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰ組立て",
"WorkItems": [
"2. CYLINDER にJOINT を取付ける",
"1. CYLINDER のﾌﾞﾗｹｯﾄの裏面に30をかけ､全体を32を塗布し組立てる"
],
"WorkPoints": [
"ｼｬﾌﾄについている標準ﾅｯﾄは廃棄のこと",
"ﾀｯﾌﾟ面",
"Dｶｯﾄとﾌﾟﾚｰﾄが平行になること",
"ｼﾞｮｲﾝﾄ取付けﾀ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2984",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰ組立て",
"WorkItems": [
"2. CYLINDER にJOINT を取付ける",
"◆3. CYLINDER にCYL-NUT を取付ける",
"1. CYLINDER のﾌﾞﾗｹｯﾄの裏面に30をかけ､全体を32を塗布し組立てる"
],
"WorkPoints": [
"ｼｬﾌﾄについている標準ﾅｯﾄは廃棄のこと",
"ﾀｯﾌﾟ面",
"Dｶｯﾄとﾌﾟﾚｰﾄが平行になること",... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾌﾞｯｼｭｸﾞﾘｰｽｱｯﾌﾟ",
"WorkItems": [
"◆1. LINEAR-BUSH の内側のﾎﾞｰﾙ部にｸﾞﾘｰｽを塗布する｡"
],
"WorkPoints": [
"開封し油を拭き取ること",
"表面に薄くｸﾞﾘｰｽを塗布すること",
"ｺﾞﾐなどが付着しないように注意すること",
"ﾘﾆｱ内部にｸﾞﾘｰｽを塗布(上下) ﾎﾞｰﾙﾍﾞｱﾘﾝｸﾞが埋まる程度に塗付し､余りは除去する｡",
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｸﾞﾘｰｽ容器:80㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾌﾞｯｼｭｸﾞﾘｰｽｱｯﾌﾟ",
"WorkItems": [
"◆1. LINEAR-BUSH の内側のﾎﾞｰﾙ部にｸﾞﾘｰｽを塗布する｡"
],
"WorkPoints": [
"開封し油を拭き取ること",
"表面に薄くｸﾞﾘｰｽを塗布すること",
"ｺﾞﾐなどが付着しないように注意すること",
"ﾘﾆｱ内部にｸﾞﾘｰｽを塗布(上下) ﾎﾞｰﾙﾍﾞｱﾘﾝｸﾞが埋まる程度に塗付し､余りは除去する｡",
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1(ﾘﾆｱ外周)",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-①",
"WorkItems": [
"1. ㉖の本体エアー配管を工場エアー配管に接続する",
"3. ㉖の圧力計を確認または調整する",
"2. ㉖のエアーバルブを開にする"
],
"WorkPoints": [
"設定圧力:0.50Mpa±0.05",
"ﾊﾝﾄﾞﾙ",
"ﾛｯｸﾅｯﾄ",
"圧力調整はロックナットを㉗で緩め、ハンド... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "0.50Mpa±0.05",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙはかり",
"Size": "",
"ToolOther": "EK-3000i",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-②",
"WorkItems": [
"3. 1完成品を㉖に乗せ、ゼロ設定する",
"2. ㉖の電源を投入する",
"3. 1完成品を㉖に乗せ、ゼロ設定する",
"2. ㉖の電源を投入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-③",
"WorkItems": [
"◆1. を㉖にセットし、内側ボール内にグリースを塗布する"
],
"WorkPoints": [
" を素手で触ら無い事",
"Hｶｯﾄ面をｶﾞｲﾄﾞに合わせる",
"ｽﾄｯﾊﾟｰに当付ける",
"2秒以上ﾎﾞﾀﾝを長押しｸﾞﾘｰｽを塗布する(ｼﾘﾝﾀﾞｰが動かなくなるまで)",
"ｸﾞﾘｰｽが塗布される... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り塗布出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙはかり",
"Size": "",
"ToolOther": "EK-3000i",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-④",
"WorkItems": [
"1. を㉖に乗せグリス塗布量を計測する"
],
"WorkPoints": [
" を素手で触ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業",
"ｸ... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "5g~7g",
"Method": "ﾃﾞｼﾞﾀﾙはかり",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-④",
"WorkItems": [
"1. を㉖に乗せグリス塗布量を計測する",
"◆2. 1完成品の表面全体に㉗グリースを塗布する（黄色部）"
],
"WorkPoints": [
"ｺﾞﾐ等が付着してい無い事を確認する事",
"特にﾕﾆｯﾄ取付面にｺﾞﾐ等が付着してい無い事",
" を素手で触ら無い事"
],
"Tolks": [],
"I... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｼｬﾌﾄ組立て、ｸﾞﾘｰｽ塗布",
"WorkItems": [
"1. PLATE にSHAFT をBOLT で仮付ける｡",
"◆2. SHAFT にｸﾞﾘｰｽを塗布する｡"
],
"WorkPoints": [
"全体(底面含む)に薄くｸﾞﾘｰｽを塗付する (小豆/1粒)× 4個",
"SHAFT の取付面に注意(ｻﾞｸﾞﾘの反対面)",
"Dｶｯﾄ面は下側にきている事"
],
"Tolks": [... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾘﾑ接着",
"WorkItems": [
"▲1. BRACKET にTRIM を接着する｡"
],
"WorkPoints": [
"下当付け",
"接着剤をｺﾞﾏ粒の量･ﾄﾘﾑ寸法長さに塗布し､ﾄﾘﾑを取付、全面に㉗で防錆する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"28㎜",
"1... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "剥がれ無い事ｺﾞﾏ粒×16㎜ｺﾞﾏ粒×28㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessName": "特殊工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. にVALVE をBOLT WASHER WASHER で取付ける",
"4. にSPEED-CONTROLLER をBOLT で取付ける"
],
"WorkPoints": [
" の向きに注意して取付けること",
"SPEED-CONTROLLER の取付け向きに注意すること",
"ﾏｰｸの向きが図の様に取付け... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. にVALVE をBOLT WASHER WASHER で取付ける",
"4. にSPEED-CONTROLLER をBOLT で取付ける"
],
"WorkPoints": [
" の向きに注意して取付けること",
"SPEED-CONTROLLER の取付け向きに注意すること",
"ﾏｰｸの向きが図の様に取付け... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. にVALVE をBOLT WASHER WASHER で取付ける",
"4. にSPEED-CONTROLLER をBOLT で取付ける"
],
"WorkPoints": [
" の向きに注意して取付けること",
"SPEED-CONTROLLER の取付け向きに注意すること",
"ﾏｰｸの向きが図の様に取付け... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. にVALVE をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
" の向きに注意して取付けること"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の長さにｶｯﾄしている事",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "上限下限ｾﾝｻ組立",
"WorkItems": [
"1. PLATE の裏側に㉘をかけ㉙を塗布する",
"2. PLATE にSENSOR SPACER をBOLT WASHER WASHER で取付ける｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "中継ｼﾞｮｲﾝﾄ組立、銘板貼付け",
"WorkItems": [
"1. BRACKET にLABEL を貼付ける｡",
"3. BRACKET にJOINT をBOLT WASHER WASHER で取付ける｡",
"2. BRACKET に㉙を塗布する。"
],
"WorkPoints": [
"BRACKET の向きに注意(ｺﾈｸﾀ穴位置を要確認)",
"BRACKET の向き... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "中継ｼﾞｮｲﾝﾄ組立、銘板貼付け",
"WorkItems": [
"1. BRACKET にLABEL を貼付ける｡",
"3. BRACKET にJOINT をBOLT WASHER WASHER で取付ける｡",
"2. BRACKET に㉙を塗布する。"
],
"WorkPoints": [
"BRACKET の向きに注意(ｺﾈｸﾀ穴位置を要確認)",
"BRACKET の向きに注意(ｺﾈｸﾀ穴位置を... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "支持ﾎﾞﾙﾄ組立",
"WorkItems": [
"1. BOLT の上面に砥石をかける｡",
"2. BOLT にNUT を仮付ける｡"
],
"WorkPoints": [
"砥石かけ部",
"ﾌﾗｯﾄ面",
"ﾅｯﾄの取付け向きに注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "加工面に打痕､傷等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "中継ｼﾞｮｲﾝﾄﾌﾟﾚｰﾄ取付け",
"WorkItems": [
"2. PLATE に をBOLT WASHER で取付ける｡",
"1. PLATE の表裏面､前側面、右側面に㉘をかける。"
],
"WorkPoints": [
"M4ﾀｯﾌﾟ穴が上にあること",
"→方向に当付けて取付ける",
"PLATE と の向きに注意して取付けること"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｲﾝｼｭﾛｯｸﾀｲ、ｲﾝｼｭﾛｯｸ取付け",
"WorkItems": [
"3. ⑯にｲﾝｼｭﾛｯｸを差込む｡",
"2. にﾏｳﾝﾄを取付ける｡",
"1. ㉙を塗布する"
],
"WorkPoints": [
"M4ﾀｯﾌﾟ穴が手前",
"⑯の方向に注意",
"ｲﾝｼｭﾛｯｸの向きに注意",
"M4ﾀｯﾌﾟ穴が手前"
],
"Tolks": [],
"InspectionNo"... | {
"QualityItem": "方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りの方向である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "5.3N･m",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰの取付け",
"WorkItems": [
"1. に を取付ける",
"2. に をBOLT WASHER で仮付ける"
],
"WorkPoints": [
" の取付け向きに注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰの取付け",
"WorkItems": [
"1. に を取付ける",
"2. に をBOLT WASHER で仮付ける"
],
"WorkPoints": [
" の取付け向きに注意",
" の継手側"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words... | {
"QualityItem": "方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りの方向である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾘﾆｱﾌﾞｯｼｭ取付け",
"WorkItems": [
"1. に をBOLT で取付ける｡"
],
"WorkPoints": [
"目視にて取付け穴のｾﾝﾀｰで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"or"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾌﾞｯｼｭ取付け",
"WorkItems": [
"1. に をBOLT で取付ける｡"
],
"WorkPoints": [
"目視にて取付け穴のｾﾝﾀｰで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"or"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞの取付け",
"WorkItems": [
"1. に をBOLT WASHER で取付ける｡"
],
"WorkPoints": [
"矢印方向に押して取付けること",
" の取付け方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞの取付け",
"WorkItems": [
"1. に をBOLT WASHER で取付ける｡"
],
"WorkPoints": [
"矢印方向に押して取付けること",
" の取付け方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りの方向である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上限下限ｾﾝｻ取付け",
"WorkItems": [
"1. にWASHER をBOLT WASHER で仮付ける｡"
],
"WorkPoints": [
"目視にて長穴中央で仮付ける",
"内輪の面取りは大きい方を上にする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける｡"
],
"WorkPoints": [
"BRACKET の向きに注意",
" の端面よりはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける｡"
],
"WorkPoints": [
"BRACKET の向きに注意",
" の端面よりはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Word... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管接続",
"WorkItems": [
"1. の配管を接続する｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"104(180mm)",
"102(250mm)",
"101(270mm)",
"ﾍﾞｰｽ下へ"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.