input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｼｬｯﾀｰ取付③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"･締付けﾄﾙｸ: 150cN･m",
"*.ｶﾞｲﾄﾞがﾍﾞｱﾘﾝｸﾞと 干渉し無い事｡",
"*.ﾍﾞｱﾘﾝｸﾞの摺動がｶﾞﾀがなく､ｽﾑｰｽﾞである事を確... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"･締付けﾄﾙｸ:95cN･m",
"･GUIDE を右側に押し当てて取付け｡",
"2. ⑧にGUIDE をSPACER BOLT で取付け｡"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "95cN･m",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"･締付けﾄﾙｸ:95cN･m",
"･GUIDE を右側に押し当てて取付け｡",
"2. ⑧にGUIDE をSPACER BOLT で取付け｡"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽﾍﾟｰｻ取付ｶﾞｰﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"2. 1.にGUARD をBOLT WASHER で取付け｡",
"･矢印方向･垂直に押し当てて取付",
"･締付けﾄﾙｸ:95cN･m",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽﾍﾟｰｻ取付ｶﾞｰﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"2. 1.にGUARD をBOLT WASHER で取付け｡",
"･矢印方向･垂直に押し当てて取付",
"･締付けﾄﾙｸ:95cN･m",
... | {
"QualityItem": "取付確認締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "動作確認治具",
"Size": "",
"ToolOther": "FM-2411",
"WorkName": "動作確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"･着脱の際､引っ掛かりが無い事",
"2.ｼｬｯﾀｰの動作確認を実施する｡",
"※1. ｷｯﾄ検査表 :ｼｬｯﾀｰ動作確認",
"･最大過重 :4N 以下",
"... | {
"QualityItem": "着脱確認",
"ToolManageNo": "FM-2411",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "引っ掛かりの無い事",
"Method": "手感",
"RecordMethod": "WCQP-C010-049",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "動作確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"･着脱の際､引っ掛かりが無い事",
"2.ｼｬｯﾀｰの動作確認を実施する｡",
"※1. ｷｯﾄ検査表 :ｼｬｯﾀｰ動作確認",
"･最大過重 :4N 以下",
"... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "最大荷重4N以下",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "WCQP-C010-049",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｾﾝﾀｰ合せ"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘｱﾙﾗﾍﾞﾙ貼付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "150cN･m",
"WorkName": "ｶﾗｰ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｶﾗｰ向き",
"･ｶﾗｰの取付方向 (Dｶｯﾄ部が横に来る様に取付)"
]
} | {
"QualityItem": "方向確認締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"2･治具ﾉｽﾞﾙ 開閉確認を実施する｡",
"SW 上側 ｼｬｯﾀｰ \u0022開 下側 ｼｬｯﾀｰ \u0022閉",
"*､ｼｬｯﾀｰ開閉が引っ掛りがなく､ｽﾑｰｽﾞである事",
... | {
"QualityItem": "自重落下確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾁｪﾝｼﾞｬｰがｽﾑｰｽﾞに落下出きる事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾁｪｯｶｰ検査ﾉｽﾞﾙ",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"2･治具ﾉｽﾞﾙ 開閉確認を実施する｡",
"SW 上側 ｼｬｯﾀｰ \u0022開 下側 ｼｬｯﾀｰ \u0022閉",
"*､ｼｬｯﾀｰ開閉が引っ掛りがなく､ｽﾑｰｽﾞで... | {
"QualityItem": "ﾉｽﾞﾙｾｯﾄ確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾉｽﾞﾙがｽﾑｰｽﾞにｾｯﾄ出きる事",
"Method": "ﾁｪｯｶｰ",
"RecordMethod": "WCQP-C010-049",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ部組立",
"WorkItems": [
"1. BRACKET にSENSOR をNUT-PLATE BOLT で取付ける(2個)",
"2. 1の完成品にBRACKET をWASHER WASHER BOLT で取付ける",
"3. 2の完成品にCABLE-SUPPORT を取付ける(2個)"
],
"WorkPoints": [
"FT4向き",
"測定位置はｾﾝｻ中心部 各位置より±0.5㎜"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟｰﾘｰ部組立",
"WorkItems": [
"1. PLATE にPLATE をBOLT で取付ける",
"2. 1の完成品にｱｲﾄﾞﾗｰﾋﾟﾝ をWASHER WASHER NUT で取付ける(2個)",
"3. 2の完成品にPULLEY PULLEY を挿入しC-RING を取付ける"
],
"WorkPoints": [
"青線部の端面を合わせる",
"WASHER 入れる場所注意",
"ｱｲﾄﾞﾗ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ部組立_1",
"WorkItems": [],
"WorkPoints": [
"KEY溝側",
"隙間 5mmﾌﾞﾛｯｸｹﾞｰｼﾞ使用",
"Dｶｯﾄ側",
"KEY溝",
"TORQUE-LIMITER の付属ﾈｼﾞ(2個)は取り外して破棄する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "170cN･m",
"WorkName": "ﾓｰﾀｰ部組立_1",
"WorkItems": [],
"WorkPoints": [
"KEY溝側",
"隙間 5mmﾌﾞﾛｯｸｹﾞｰｼﾞ使用",
"Dｶｯﾄ側",
"KEY溝",
"TORQUE-LIMITER の付属ﾈｼﾞ(2個)は取り外して破棄する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "170cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ部組立_2",
"WorkItems": [
"2. 1の完成品にBRACKET をBOLT WASHER で取付ける",
"1. にﾌﾟｰﾘ(1) を挿入し､ｽﾄｯﾌﾟﾘﾝｸﾞを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｽﾄｯﾌﾟﾘﾝｸﾞ(N005付属品)",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_1",
"WorkItems": [
"3. 2の完成品にBALL-SCREW を挿入しBOLT WASHER で取付ける",
"1. BEARING の余分な油を清掃後､BEARING を重ねてNUT に挿入する",
"2. 1の完成品にKEY を圧入する"
],
"WorkPoints": [
"この作業ﾍﾟｰｼﾞでは同じ物を2個製作する",
"BEARING の側面のﾏｰｸをVの字に合わせる事",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_2",
"WorkItems": [
"2. LOCK-NUT を1の完成品に締め付けて固定する",
"1. にﾌﾟﾚｰﾄ を挿入後､ﾌﾟｰﾘ(2) とﾌﾟｰﾘ(3) を挿入する｡",
"3. 2の完成品をSCREW で固定する"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ はﾌﾟｰﾘｰ側にｻﾞｸﾞﾘ穴があるように取付ける",
"LOCK-NUT 取付向き注意",
"締め終えたら注記箇... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "隙間無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_3",
"WorkItems": [
"1. にﾌﾟﾚｰﾄ を挿入後､ｽﾍﾟｰｻ とﾌﾟｰﾘ(2) を挿入する",
"2. LOCK-NUT を1の完成品に締め付けて固定する",
"3. 2の完成品をSCREW で固定する"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ はﾌﾟｰﾘｰ側にｻﾞｸﾞﾘ穴があるように取付ける",
"LOCK-NUT 取付向き注意",
"締め終えたら注記箇所に隙... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "隙間無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_4",
"WorkItems": [
"1. ｹｰｽ にBUSH を挿入しSCREW で取付ける"
],
"WorkPoints": [
"この作業ﾍﾟｰｼﾞでは同じ物を2個製作する",
"BUSH の凹み部分がｹｰｽ の穴と合うように挿入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_5",
"WorkItems": [
"1. に を挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
" と を端面で合わせて取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"端面を合わせる",
"端面を合わせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_6",
"WorkItems": [
"1. に を挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
" と を端面で合わせて取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"端面を合わせる",
"端面を合わせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_7(ﾓｰﾀｰ側)",
"WorkItems": [
"1. にﾍﾞﾛｰｽﾞ を挿入する",
"2. PIN を挿入しPIN で固定する"
],
"WorkPoints": [
"軸を回しPIN が入るように穴を合わせる",
"PIN とPIN の取付拡大図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_8(従動側)",
"WorkItems": [
"1. にﾍﾞﾛｰｽﾞ を挿入する",
"2. PIN を挿入しPIN で固定する"
],
"WorkPoints": [
"軸を回しPIN が入るように穴を合わせる",
"PIN とPIN の取付拡大図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_9",
"WorkItems": [
"1. と にﾌﾞｯｼｭ を挿入しBOLT で取付ける"
],
"WorkPoints": [
"ﾌﾞｯｼｭ は奥まで挿入してからﾈｼﾞを入れるようにすること",
"ﾓｰﾀｰ側(ﾌﾟｰﾘｰ2個)",
"従動側(ﾌﾟｰﾘｰ1個)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_10",
"WorkItems": [
"2. 1の完成品に をBOLT WASHER で取付ける",
"3. (従動側)に をBOLT WASHER で矢印の方向に仮止めする",
"1. (ﾓｰﾀｰ側)に をBOLT WASHER で矢印の方向に仮止めする"
],
"WorkPoints": [
"ﾓｰﾀｰ側(ﾌﾟｰﾘｰ2個)",
"ﾓｰﾀｰ側(ﾌﾟｰﾘｰ2個)",
"従動側(ﾌﾟｰﾘｰ1... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_11",
"WorkItems": [
"1. PLATE にBOLT NUT を取付ける",
"2. 1の完成品を にBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾈｼﾞ出代 7㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:7㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ組立",
"WorkItems": [
"1. CHANNEL にSHAFT をWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"下から見た図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Oﾘﾝｸﾞ取付",
"WorkItems": [
"●1. のOリング溝とO-RING を清掃後、O-RING に㉘を塗布し のOリング溝に取付ける",
"2. 1の完成品を㉘で軽く拭く"
],
"WorkPoints": [
"ﾓｰﾀｰ側",
"従動側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部取付",
"WorkItems": [
"1. ⑥の〇で示した部分を㉗㉘で清掃する",
"2. 1の完成品に をWASHER BOLT で取付ける"
],
"WorkPoints": [
"底面から見た図",
"ﾓｰﾀｰ側",
"従動側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "T-BELT取付",
"WorkItems": [
"2. の従動側の昇降部にある〇印のﾈｼﾞを緩めﾌﾞﾗｹｯﾄを動かしてT-BELT を張り､再度ねじを仮締めする",
"1. のﾓｰﾀｰ側の昇降部にある〇印のﾈｼﾞを緩めﾓｰﾀｰを動かしてT-BELT を張り､再度ねじを仮締めする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "U-507",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整_1",
"WorkItems": [
"1. ﾓｰﾀｰ側の昇降部の〇印のﾎﾞﾙﾄを緩め､左右に動かしながらﾍﾞﾙﾄﾃﾝｼｮﾝを調整する"
],
"WorkPoints": [
"ﾍﾞﾙﾄ張力計の設定が下記数値になっていることを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "50~70N",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀｰﾌﾞﾚｰｷ解除治具",
"Size": "",
"ToolOther": "FM-3229",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部高さ調整",
"WorkItems": [
"1. のモーターのコネクタに㉖を取付ける",
"2. ㉖のプラグをコンセントに繋ぎ、スイッチをONにする",
"3. ﾓｰﾀｰﾌﾞﾚｰｷ解除後､ のｼｬﾌﾄの出代を調整する"
],
"WorkPoints": [
"ﾓｰﾀｰ",
"治具",
"BKがﾌﾞﾚｰｷ解除のｺﾈｸﾀになる",
"ｼｬﾌﾄ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-3229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部高さ調整",
"WorkItems": [],
"WorkPoints": [
"ﾓｰﾀｰ",
"BKがﾌﾞﾚｰｷ解除のｺﾈｸﾀになる",
"ﾍﾞﾙﾄを動かすと連結しているので､両方のｼｬﾌﾄが動いてしまう"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"M60□BKR",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "±0.1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "U-507",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整_2",
"WorkItems": [
"1. 従動側の昇降部の〇印のﾎﾞﾙﾄを緩め､左右に動かしながらﾍﾞﾙﾄﾃﾝｼｮﾝを調整する",
"2. ベルトテンション調整後、シャフトの出代を再度確認し規格内なら㉖を取り外す"
],
"WorkPoints": [
"ﾃﾝｼｮﾝ規格値:50~70N",
"ﾍﾞﾙﾄ張力計の設定が下記数値になっていることを確認する",
"規格外の場合はSD... | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "50~70N",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"下から見た図",
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DOG取付",
"WorkItems": [
"1. にDOG をBOLT WASHER で取付ける",
"2. ｾﾝｻｰとDOG の位置関係を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"下から見た図",
"ｾﾝｻｰ(ｸﾗﾝﾌﾟ原点)",
"ｾﾝｻｰ(ｸ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整1",
"WorkItems": [
"1. を㉖に接続する",
"2. ㉖の背面にある電源をONにする",
"3. 画面右上のPower ONﾎﾞﾀﾝと〇印のﾎﾞﾀﾝを同時に押す"
],
"WorkPoints": [
"治具",
"ﾓｰﾀｰ",
"ｾﾝｻ接続の線はDOGが動くので当たらないように止めておく",
"右上のPower ONが黄色にならないと検査... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整2",
"WorkItems": [
"1. ﾌﾟﾛｾｽﾁｬﾝﾊﾞｰ調整/検査のﾎﾞﾀﾝを押す",
"2. センサ確認画面がでるので\u3000\u3000クランプ昇降部のセンサが反応するか㉗で遮光し確認する",
"3. 左下のMenuﾀﾌﾞを押す",
"4. 下にﾀﾌﾞが出てくるので､左から3番目のMoterを押す"
],
"WorkPoints": [],
"Tolks": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整3",
"WorkItems": [
"1. 〇印の部分が有効になっていることを確認する",
"2. 移動量を 41.3 に数値を設定する"
],
"WorkPoints": [
"無効になってる場合はﾎﾞﾀﾝを押して有効に切り替える"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整4",
"WorkItems": [
"1. 原点のｼｬﾌﾄの高さを測る",
"3. JOG DownもしくはMOVEを押し､原点をずらしてから再度Originを押し原点復帰を行い､1の作業に戻る"
],
"WorkPoints": [
"高さ75.3㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
"どちらかでずらす",
"原点復帰",
"※高... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "75.3±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整4",
"WorkItems": [
"1. 原点のｼｬﾌﾄの高さを測る",
"3. JOG DownもしくはMOVEを押し､原点をずらしてから再度Originを押し原点復帰を行い､1の作業に戻る"
],
"WorkPoints": [
"高さ75.3㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
"どちらかでずらす",
"原点復帰",
"※高さが... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整5",
"WorkItems": [
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合は､PH166(下降)の位置を動かして調整を行う"
],
"WorkPoints": [
"※高さが出ていたらこの作業は必要ない",
"どちらかでずらす",
"下限位置",
"※高さが出ていたらこの作... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "34.0±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整5",
"WorkItems": [
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合は､PH166(下降)の位置を動かして調整を行う",
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合は､PH166(下降)の位置を動かして調整を行う"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾈｼﾞ取付",
"WorkItems": [
"1. にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "X軸真直確認治具",
"Size": "",
"ToolOther": "FM-2209",
"WorkName": "左側ｶﾞｲﾄﾞ組立1/3",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
"FM-2209",
"BRACKET の幅を㉖で広げる"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2209",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立1/3",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
"FM-2209",
"BRACKET の幅を㉖で広げる"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. にTAPE を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事",
"端面40㎜から貼付け",
"表面の端面 6mmから貼付"
],
"Tolks... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. にTAPE を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事",
"端面40㎜から貼付け",
"表面の端面 6mmから貼付"
],
"Tolks":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. にTAPE を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事",
"端面40㎜から貼付け",
"表面の端面 6mmから貼付"
],
"Tolks": [
"締... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. にTAPE を貼付ける",
"1. にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. にTAPE を貼付ける",
"1. にBRACKET をB... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立3/3",
"WorkItems": [
"1. GUIDE へTAPE を貼付ける",
"2. 1.完成品を へBOLT WASHER で取付ける"
],
"WorkPoints": [
"右側ｴｯｼﾞ部から貼付けて気泡が入らない様貼付ける事",
"GUIDE の取付位置は長穴ｾﾝﾀｰで取付ける取付の際中央位置を仮固定し両ｻｲﾄﾞで確認し位置決めする"
],
"Tolks":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立3/3",
"WorkItems": [
"1. GUIDE へTAPE を貼付ける",
"2. 1.完成品を へBOLT WASHER で取付ける"
],
"WorkPoints": [
"右側ｴｯｼﾞ部から貼付けて気泡が入らない様貼付ける事",
"GUIDE の取付位置は長穴ｾﾝﾀｰで取付ける取付の際中央位置を仮固定し両ｻｲﾄﾞで確認し位置決めする"
],
"Tolks": [],
... | {
"QualityItem": "貼付け確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側ｶﾞｲﾄﾞ組立1/2",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"FM-2209"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 9.8N･m",
"BOLT 締付ﾄﾙｸ 10.9N･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "10.9N･m",
"WorkName": "右側ｶﾞｲﾄﾞ組立1/2",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"FM-2209"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 9.8N･m",
"BOLT 締付ﾄﾙｸ 10.9N･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右側ｶﾞｲﾄﾞ組立2/2",
"WorkItems": [
"1. にCOVER を取付ける",
"1. にCOVER を取付ける"
],
"WorkPoints": [
"端面40㎜から取付ける",
"端面40㎜から取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. PLATE にPLATE をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"塗装面無しをこちら側へ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀｰ\u0026ｼﾞｮｲﾝﾄ部組立1/2",
"WorkItems": [
"1. BRACKET にJOINT を挿入しJOINT の付属ﾅｯﾄで固定する"
],
"WorkPoints": [
"JOINT の付属品"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "ｺﾈｸﾀｰ\u0026ｼﾞｮｲﾝﾄ部組立2/2",
"WorkItems": [
"1. にCONNECTOR CONNECTOR をBOLT WASHER で取付ける"
],
"WorkPoints": [
"CONNECTOR を左､CONNECTOR を右に取付｡CONNECTOR とCONNECTOR は大きさが違う為､取付位置を間違わ無い事CONNECTOR CONNECTOR の取付方向も内側の山の部... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. PLATE にPIN を圧入する"
],
"WorkPoints": [
"4㎜",
"ﾋﾟﾝ出代:4㎜",
"ﾈｼﾞ穴ﾋﾟｯﾁを参照にD-pinを圧入"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 1.完成品にBRACKET をBOLT WASHER で取付ける",
"3. 2.完成品にBOLT WASHER を挿入し､STOPPER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. 1.完成品にBRACKET をBOLT WASHER で取付ける",
"3. 2.完成品にBOLT WASHER を挿入し､STOPPER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"4㎜",
"ﾋﾟﾝ出代:4㎜",
"ﾈｼﾞ穴ﾋﾟｯﾁを参照にD-pinを... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品",
"WorkItems": [
"1. PLATE ~ WASHER BOLT を3工程に払い出す",
"2. を1工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "部品が揃っている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ組立",
"WorkItems": [],
"WorkPoints": [
"収縮ﾁｭｰﾌﾞ品番:SMTFZ-2-5P"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5mBOX",
"ToolOther": "60cN･m",
"WorkName": "TERMINAL組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀｰﾐﾅﾙ取付確認時ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5198",
"WorkName": "TERMINAL組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5198",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部ｹｰﾌﾞﾙ接続",
"WorkItems": [
"2. CABLE のP3ｺﾈｸﾀに､POWER-SUPPLY のP3ｺﾈｸﾀを接続する",
"3. 青ﾏｰｷﾝｸﾞする(1箇所)",
"■1. POWER-SUPPLY の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無､認証ﾏｰｸを確認し検査表に記入する",
"4. 配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯというまで確実に接続す... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-200052LC-JG-15021",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部ｹｰﾌﾞﾙ接続",
"WorkItems": [
"2. CABLE のP3ｺﾈｸﾀに､POWER-SUPPLY のP3ｺﾈｸﾀを接続する",
"3. 青ﾏｰｷﾝｸﾞする(1箇所)",
"■1. POWER-SUPPLY の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無､認証ﾏｰｸを確認し検査表に記入する",
"4. 配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯというまで確実に接続す... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-200052LC-JG-15021",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "電源部ｹｰﾌﾞﾙ接続",
"WorkItems": [
"2. CABLE のP3ｺﾈｸﾀに､POWER-SUPPLY のP3ｺﾈｸﾀを接続する",
"3. 青ﾏｰｷﾝｸﾞする(1箇所)",
"■1. POWER-SUPPLY の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無､認証ﾏｰｸを確認し検査表に記入する",
"4. 配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯというま... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀﾎﾞｰﾄﾞ確認",
"WorkItems": [
"■1. PCB-COM の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する"
],
"WorkPoints": [
"添付検査書:2LC-JG-20003"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-200042LC-JG-20005",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀﾎﾞｰﾄﾞ確認",
"WorkItems": [
"■1. PCB-COM の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する"
],
"WorkPoints": [
"添付検査書:2LC-JG-20003"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-200042LC-JG-20005",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定全てOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
"参... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-200042LC-JG-20005",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ設定",
"WorkItems": [
"2. CAMIF2 BOARD のJP1~8の設定を確認し､DIPSWの設定を行う",
"■1. CAMIF2 BOARD の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無ﾁｪｯｸをする"
],
"WorkPoints": [
"SW1設定全てOFFの事",
"ｼﾞｬﾝﾊﾟｰ設定JP1･3･5･7:1-2間ｼｮｰﾄJP2･4･6･8:2-3間ｼｮｰﾄ",
"参... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-200042LC-JG-20005",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "30cN･m",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け1",
"WorkItems": [
"1. にSPACER をSCREW WASHER で取付ける",
"2. 1完成品に を載せる"
],
"WorkPoints": [
"ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀのｶﾒﾗI/Fﾎﾞｰﾄﾞｺﾈｸﾀ部に基板を入れてPCI-Eｺﾈｸﾀの勘合を行う",
"勘合の際､各基板に過度のｽﾄﾚｽをかけない様注意する事",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け1",
"WorkItems": [
"1. にSPACER をSCREW WASHER で取付ける",
"2. 1完成品に を載せる"
],
"WorkPoints": [
"ｺﾝﾊﾟｸﾄPCIﾎﾞｰﾄﾞｺﾝﾋﾟｭｰﾀのｶﾒﾗI/Fﾎﾞｰﾄﾞｺﾈｸﾀ部に基板を入れてPCI-Eｺﾈｸﾀの勘合を行う",
"勘合の際､各基板に過度のｽﾄﾚｽをかけない様注意する事",
"SPACER の線を下にし... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20004",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ4.0㎜",
"ToolOther": "10cN･m",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m",
"締付ﾄﾙｸ 35cN･m"
],
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "35cN･m",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m",
"締付ﾄﾙｸ 35cN･m"
],
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "35cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける",
"3. 2完成品にLABEL を貼付ける",
"4. CPUﾎﾞｰﾄﾞのｼﾘｱﾙNo.を確認し､記録する"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001",
"ﾊﾟﾈﾙのｼﾙｸ印刷ﾗｲﾝに合わせて貼付ける"
]... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20004",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける",
"3. 2完成品にLABEL を貼付ける",
"4. CPUﾎﾞｰﾄﾞのｼﾘｱﾙNo.を確認し､記録する"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001",
"ﾊﾟﾈﾙのｼﾙｸ印刷ﾗｲﾝに合わせて貼付ける"
]... | {
"QualityItem": "貼付け確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20004",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗI/F2ﾎﾞｰﾄﾞ取付け2",
"WorkItems": [
"1. にSCREW を取付ける",
"2. 1完成品をSCREW WASHER で取付ける",
"3. 2完成品にLABEL を貼付ける",
"4. CPUﾎﾞｰﾄﾞのｼﾘｱﾙNo.を確認し､記録する"
],
"WorkPoints": [
"参考手順書:2LC-JF-20001",
"ﾊﾟﾈﾙのｼﾙｸ印刷ﾗｲﾝに合わせて貼付ける"
]... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-15021",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝﾀｰﾚｰﾙ前組立",
"WorkItems": [
"1. RAIL の指定箇所に､INSULATOR の上を引っ掛け､左基準で穴位置を合わせ押し込む"
],
"WorkPoints": [
"INSULATOR の取付位置･方向に注意する事(写真参照)",
"ｶﾁｯというまで確実に取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱﾚｰﾙ前組立",
"WorkItems": [
"1. RAIL の指定箇所に､INSULATOR の上を引っ掛け､左基準で穴位置を合わせ押し込む"
],
"WorkPoints": [
"INSULATOR の取付位置･方向に注意する事(写真参照)",
"ｶﾁｯというまで確実に取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾙ取付1",
"WorkItems": [
"1. COVER の指定箇所にRAIL をｾｯﾄし､SCREW で仮締めする(2箇所)",
"2. 1.の完成品のRAIL にPLATE を面取り部を前面にして切断面から挿入する"
],
"WorkPoints": [
"指定箇所は写真参照 ･RAIL の取付方向に注意する事 ･COVER のﾀﾞﾎﾞにあてつける事",
"SD-A026382-019で本締結"
],
"T... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾙ取付2",
"WorkItems": [
"1. の指定箇所にRAIL をｾｯﾄし､SCREW で仮締めする",
"2. の指定箇所に をｾｯﾄし､SCREW で仮締めする",
"3. の指定箇所に をｾｯﾄし､SCREW で仮締めする"
],
"WorkPoints": [
"･指定箇所は写真参照 ･RAIL の取付方向に注意する ･ｶﾊﾞｰのﾀﾞﾎﾞにあてつける事",
"SD-A026382-019で本締結... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "BRACKET仮締め",
"WorkItems": [
"1. にBRACKET をかぶせる",
"2. BRACKET 右側面と中のﾚｰﾙの穴位置を合わせて､SCREW で仮締めする(5箇所)",
"3. とBRACKET の上面の穴位置を合わせて､SCREW で仮締めする(3箇所)",
"4. とBRACKET 右側面下部の穴位置を合わせて､SCREW で仮締めする"
],
"WorkPoints": [
"BR... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "GUIDE取付",
"WorkItems": [
"1. のﾚｰﾙをGUIDE の取付穴､左から3番目にGUIDE をｾｯﾄし､上から押し込み取付ける(4箇所)",
"2. を反転させ､GUIDE のﾚｰﾙを の取付穴の右から3番目にｾｯﾄし､上から押し込み取付ける(4箇所)"
],
"WorkPoints": [
"･GUIDE の取付け方向に注意する事(写真参照) ･ｶﾁｯと音がするまで押し込む事",
"･GUIDE の... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM確認",
"WorkItems": [
"■1. PCB-COM の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"■2. PCB-COM のJ1及びPS-ONにｼﾞｬﾝﾊﾟｰﾋﾟﾝが入っている事を確認し､検査書に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-15021",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM確認",
"WorkItems": [
"■1. PCB-COM の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"■2. PCB-COM のJ1及びPS-ONにｼﾞｬﾝﾊﾟｰﾋﾟﾝが入っている事を確認し､検査書に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-15021",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PCB-COM仮取付",
"WorkItems": [
"2. のﾚｰﾙ穴と､ の穴位置を合せ､SCREW で仮締めする(8箇所)",
"1. の裏面を手前にする"
],
"WorkPoints": [
"SD-A026382-018で本締結",
"･ﾚｰﾙと の間にINSULATORがある事 ･ﾚｰﾙの右端から3つ目に穴位置を合せる事 ･基板調整の為､仮締めにする事"
],
"Tolks": [],
"Ins... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め1",
"WorkItems": [
"■1. NCIO2 BOARD(PANA) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. の指定箇所に､NCIO2 BOARD(PANA) を挿入しながら､PCB-COM基板との差込具合を確認する"
],
"WorkPoints": [
"無理に押し込ま無い事",
"PCB-COM基板",
"指定箇所は絵参照",
"矢... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-20005",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め1",
"WorkItems": [
"■1. NCIO2 BOARD(PANA) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. の指定箇所に､NCIO2 BOARD(PANA) を挿入しながら､PCB-COM基板との差込具合を確認する"
],
"WorkPoints": [
"無理に押し込ま無い事",
"PCB-COM基板",
"指定箇所は絵参照",
"矢... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-20005",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め1",
"WorkItems": [
"■1. NCIO2 BOARD(PANA) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. の指定箇所に､NCIO2 BOARD(PANA) を挿入しながら､PCB-COM基板との差込具合を確認する"
],
"WorkPoints": [
"無理に押し込ま無い事",
"PCB-COM基板",
"指定箇所は絵参照",
"矢... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め2",
"WorkItems": [
"1. の指定箇所に､ を挿入しながらPCB-COM基板との差込具合を確認する"
],
"WorkPoints": [
"無理に押し込ま無い事",
"PCB-COM基板",
"ﾌｯｸが確実にかかるか確認する事",
"指定箇所は絵参照",
"差込位置､方向を間違え無い事",
"矢印部を押しながらﾚﾊﾞｰを上げゆっくり取付ける事",
"ここの... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "PCB-COM締付",
"WorkItems": [],
"WorkPoints": [
"確実に締結されている事",
"SD-A026382-015の本締結"
],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "BRACKET締付1",
"WorkItems": [
"1. )のﾌﾞﾗｹｯﾄとﾚｰﾙを仮固定したﾈｼﾞ(10-M4X8,SW,PW)を､本締めする(10箇所)",
"2. 青ﾏｰｷﾝｸﾞする(10箇所)"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "BRACKET締付2",
"WorkItems": [
"2. のﾌﾞﾗｹｯﾄ下部を仮固定したﾈｼﾞ(3-M3X6,SW,PW)を､本締めする(3箇所)→青ﾏｰｷﾝｸﾞ(3箇所)",
"1. ﾌﾞﾗｹｯﾄ上面を仮固定したﾈｼﾞ(3-M3X6,SW,PW)を､本締めする(3箇所)→青ﾏｰｷﾝｸﾞ(3箇所)",
"2. のﾌﾞﾗｹｯﾄ下部を仮固定したﾈｼﾞ(3-M3X6,SW,PW)を､本締めする(3箇所)→青ﾏｰ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板取付確認",
"WorkItems": [
"1. のa部に､外したCPUﾎﾞｰﾄﾞを差込み､奥のPCB-COM基板に挿入しながら､差込不具合を確認し､外す",
"2. のb部に､外したCPUﾎﾞｰﾄﾞを差込み､奥のPCB-COM基板に挿入しながら､差込不具合を確認し､外す",
"3. 確認終了後､NCﾎﾞｰﾄﾞを外す"
],
"WorkPoints": [
"･差込位置･方向を間違え無い事 ･無理に押し込ま無い事 ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "ﾌﾞﾗﾝｸﾊﾟﾈﾙ取付",
"WorkItems": [
"1. の正面を手前にする",
"3. 青ﾏｰｷﾝｸﾞをする(2箇所)",
"2. にPANEL PANEL をﾌﾞﾗｹｯﾄ側に沿わせながらPANEL PANEL (2-付属ﾈｼﾞ)で締付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.