input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ取付",
"WorkItems": [
"1. SHAFT にBOLT WASHER を仮取付",
"2. 1完成品を に挿入し固定ﾎﾞﾙﾄを仮止め"
],
"WorkPoints": [
"右側上ｱｰﾑ",
"左側上ﾌﾟﾚｰﾄ",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"右側下ｱｰﾑ",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"ﾎﾞﾙﾄ側が上",
"Dｶｯﾄをﾎﾞﾙﾄ側に合わせる",
"Dｶｯﾄ",
"固定ﾎﾞﾙﾄ",
"Dｶｯﾄ",
"Dｶｯﾄをﾎﾞﾙﾄ側に合わせる",
"固定ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A041086-410にて本締め",
"仮止め:SD-A041086-410にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"3. 下側ｼｬｯﾀｰ部の位置を調整する"
],
"WorkPoints": [
"ｼｬﾌﾄ両側を治具に当付ける(左右のﾎﾞﾙﾄにて固定する)",
"治具を当付け隙間無い事(0.01㎜)",
"原点位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"3. 上側ｼｬｯﾀｰ部の位置を調整する"
],
"WorkPoints": [
"ｼｬﾌﾄを治具に当付ける",
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整ﾎﾞﾙﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼｬﾌﾄ位置の確認"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けできていること",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼｬﾌﾄ位置の確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼｬﾌﾄ位置の確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼｬﾌﾄ位置の確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.15㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼｬﾌﾄ位置の確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼｬﾌﾄ位置の確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [
"1. にﾏｶﾞｼﾞﾝ､ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 1完成品のﾄﾚｲﾊﾟﾚｯﾄと前面扉ｶﾞｲﾄﾞの隙間を調整する"
],
"WorkPoints": [
"通し:0.4㎜ 止まり:0.5㎜",
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾏｶﾞｼﾞﾝ上下段に挿入",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"説明の為に前面扉は消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :前面扉ｶﾞｲﾄﾞﾞの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [
"1. にﾏｶﾞｼﾞﾝ､ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 1完成品のﾄﾚｲﾊﾟﾚｯﾄと前面扉ｶﾞｲﾄﾞの隙間を調整する"
],
"WorkPoints": [
"通し:0.4㎜ 止まり:0.5㎜",
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾏｶﾞｼﾞﾝ上下段に挿入",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"説明の為に前面扉は消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :前面扉ｶﾞｲﾄﾞﾞの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [
"1. にﾏｶﾞｼﾞﾝ､ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 1完成品のﾄﾚｲﾊﾟﾚｯﾄと前面扉ｶﾞｲﾄﾞの隙間を調整する"
],
"WorkPoints": [
"通し:0.4㎜ 止まり:0.5㎜",
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾏｶﾞｼﾞﾝ上下段に挿入",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"説明の為に前面扉は消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :前面扉ｶﾞｲﾄﾞﾞの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "前面扉押込み防止ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. の押込み防止ｽﾄｯﾊﾟｰとﾌﾚｰﾑの隙間を調整する"
],
"WorkPoints": [
"説明の為に前面扉は消しています",
"ﾌﾚｰﾑに当付ける",
"平行に取付け"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する",
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"0.4㎜が通り0.5㎜が通ら無い事",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"1､ ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰを隙間なく当付け調整する2 ､ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰを調整する",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬｯﾀｰｼｬﾌﾄに当付ける",
"0.4㎜が通り0.5㎜が通ら無い事",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"1､ ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰを隙間なく当付け調整する2 ､ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰを調整する",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬｯﾀｰｼｬﾌﾄに当付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :補給部ｽﾄｯﾊﾟｰの確認",
"検査表 :補給部ｽﾄｯﾊﾟｰの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する",
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"0.4㎜が通り0.5㎜が通ら無い事",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"1､ ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰを隙間なく当付け調整する2 ､ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰを調整する",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬｯﾀｰｼｬﾌﾄに当付ける",
"0.4㎜が通り0.5㎜が通ら無い事",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"1､ ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰを隙間なく当付け調整する2 ､ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰを調整する",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬｯﾀｰｼｬﾌﾄに当付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :補給部ｽﾄｯﾊﾟｰの確認",
"検査表 :補給部ｽﾄｯﾊﾟｰの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"0.4㎜が通り0.5㎜が通ら無い事",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"1､ ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰを隙間なく当付け調整する2 ､ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰを調整する",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬｯﾀｰｼｬﾌﾄに当付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :補給部ｽﾄｯﾊﾟｰの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :NG排出部ｽﾄｯﾊﾟｰの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :NG排出部ｽﾄｯﾊﾟｰの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :NG排出部ｽﾄｯﾊﾟｰの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "補給部ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. にLABEL を貼付ける"
],
"WorkPoints": [
"ﾗﾍﾞﾙの端面がﾄﾚｲﾊﾟﾚｯﾄに隠れ無い事",
"ｱﾙｺｰﾙ使用時には保護ﾒｶﾞﾈ着用の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"60㎜",
"60㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾁｪｯｶｰ接続と立ち上げ",
"WorkItems": [
"3. PC画面が立ち上がったらNPM-GWのｱｲｺﾝをﾀﾞﾌﾞﾙｸﾘｯｸ",
"5. ｼｽﾃﾑ立ち上げ",
"1. ﾄﾚｲ本体とﾁｪｯｶｰを接続する",
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝの立ち上げ",
"4.ﾁｪｯｶｰの電源BOXとｻｰﾎﾞSWをON"
],
"WorkPoints": [
"･ﾁｪｯｶｰ電源接続･ﾒｲﾝｴｱｰ接続･ｴｱｰ配管･ｺﾈｸﾀ大-TRAY･S ･･･内側 ･ｺﾈｸﾀ小-TRAY･P ･･･外側 各々接続",
"FM-2294",
"部署等を入力",
"ﾊﾞｰｺｰﾄﾞﾘｰﾀﾞｰでQRｺｰﾄﾞを読み取り",
"ﾊﾞｰｺｰﾄﾞ情報入力",
"PnP情報書込み",
"PnP情報書込み完了",
"ON",
"ﾊﾞｰｺｰﾄﾞﾘｰﾀﾞｰがUSBﾎﾟｰﾄに挿入されているのを確認する",
"ON",
"ﾄﾚｲﾌｨｰﾀﾞ本体の電源が入り待機状態になる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整①",
"WorkItems": [
"1. 原点復帰を行う",
"1. 原点復帰を行う",
"3. 補給部にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"補給部ｶﾊﾞｰを閉じﾄﾚｲﾊﾟﾚｯﾄがﾏｶﾞｼﾞﾝｼｬｯﾀｰに当っている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.6㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.8㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.15㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸原点登録",
"WorkItems": [
"2. TP軸をﾊﾟﾜｰONする",
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",
"稼働部ﾌﾟﾚｰﾄ端面",
"メカスト端面と稼働プレート端面に㉘を挟み込み、その位置でプーリーのボルトを締め付け",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸を原点復帰する",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"TP軸原点ｾﾝｻ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ",
"SD-AD051313-441で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出し部調整治具",
"Size": "",
"ToolOther": "FM-6646",
"WorkName": "TP軸原点登録",
"WorkItems": [
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6646",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸原点登録",
"WorkItems": [],
"WorkPoints": [
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸原点登録",
"WorkItems": [
"2. TP軸をﾊﾟﾜｰONする",
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",
"稼働部ﾌﾟﾚｰﾄ端面",
"メカスト端面と稼働プレート端面に㉘を挟み込み、その位置でプーリーのボルトを締め付け",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸を原点復帰する",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"TP軸原点ｾﾝｻ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ",
"SD-AD051313-441で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整",
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.9㎜で投光1.0㎜で遮光する事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整①",
"WorkItems": [
"1. ﾊﾟﾜｰONする",
"2. TL軸原点復帰を行う",
"3. 引き出部を原点位置から下段23Slot高さへ移動する"
],
"WorkPoints": [
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"FM-2848治具が取付いて無い事を確認｡ﾚﾊﾞｰが回転して危険です",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意のこと",
"原点位置まで下降する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘﾌﾄ上昇"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す",
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"5. 各治具を取り出す",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"引き出部"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取外す事",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"5. 各治具を取り出す",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"引き出部"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"引き出部"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する",
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する"
],
"WorkPoints": [
"O/Rｾﾝｻが投光",
"㉙を矢印方向に当付け"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.1㎜"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.1㎜で投光、原点で遮光する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "ﾛﾝｸﾞﾋﾞｯﾄ2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する"
],
"WorkPoints": [
"O/Rｾﾝｻが投光",
"㉙を矢印方向に当付け"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.1㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整治具",
"Size": "",
"ToolOther": "FM-6449",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する"
],
"WorkPoints": [
"傾き無き事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6449",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "傾き無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝ確認とｴｰｼﾞﾝｸﾞ実施",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞの実施",
"1. ﾁｪｯｶｰ画面に表示されてあるﾌｧｰﾑﾊﾞｰｼﾞｮﾝを確認"
],
"WorkPoints": [
"ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録する",
"ｴﾗｰ停止無い事",
"高速になっている事を確認",
"ﾁｪｯｶｰ画面で90ｻｲｸﾙを入力し12hの連続運転を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｴｰｼﾞﾝｸﾞ",
"検査表①:ﾌｧｰﾑﾊﾞｰｼﾞｮﾝの確認"
]
} | {
"QualityItem": "ｴｰｼﾞﾝｸﾞ動作",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "12時間:ｴﾗｰ停止が無いこと",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝ確認とｴｰｼﾞﾝｸﾞ実施",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞの実施",
"1. ﾁｪｯｶｰ画面に表示されてあるﾌｧｰﾑﾊﾞｰｼﾞｮﾝを確認"
],
"WorkPoints": [
"ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録する",
"ｴﾗｰ停止無い事",
"高速になっている事を確認",
"ﾁｪｯｶｰ画面で90ｻｲｸﾙを入力し12hの連続運転を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｴｰｼﾞﾝｸﾞ",
"検査表①:ﾌｧｰﾑﾊﾞｰｼﾞｮﾝの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "ﾊﾞｰｼﾞｮﾝ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了後､ﾅｯﾄ2か所にて固定する",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ(ﾅｯﾄ) 9.8N･m",
"締付ﾄﾙｸ(ﾅｯﾄ) 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定",
"WETE-G002-A11"
]
} | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "74±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "9.8N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了後､ﾅｯﾄ2か所にて固定する",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ(ﾅｯﾄ) 9.8N･m",
"締付ﾄﾙｸ(ﾅｯﾄ) 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "3.2N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了後､ﾅｯﾄ2か所にて固定する",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ(ﾅｯﾄ) 9.8N･m",
"締付ﾄﾙｸ(ﾅｯﾄ) 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙線部にはめる",
"調節ﾈｼﾞ",
"㉚のハンドルを青矢印方向に押す、調節ネジをねじ込みモータを押し上げる",
"㉚使用方法",
"橙丸ボルトを緩め、㉚にてテンション調整。完了後、締め付け"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定",
"WETE-G002-A11"
]
} | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "59±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙線部にはめる",
"調節ﾈｼﾞ",
"㉚のハンドルを青矢印方向に押す、調節ネジをねじ込みモータを押し上げる",
"㉚使用方法",
"橙丸ボルトを緩め、㉚にてテンション調整。完了後、締め付け"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄﾃﾝｼｮﾝｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6591",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙線部にはめる",
"調節ﾈｼﾞ",
"㉚のハンドルを青矢印方向に押す、調節ネジをねじ込みモータを押し上げる",
"㉚使用方法",
"橙丸ボルトを緩め、㉚にてテンション調整。完了後、締め付け"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6591",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸合いﾏｰｸ追加",
"WorkItems": [
"1. TP軸を原点復帰する",
"2. 合いﾏｰｸを付ける"
],
"WorkPoints": [
"黄色ﾏｰｶｰ2ヵ所",
"画面上で ②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TP軸合ﾏｰｸ追加"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸合いﾏｰｸ追加",
"WorkItems": [
"1. TP軸を原点復帰する",
"2. 合いﾏｰｸを付ける"
],
"WorkPoints": [
"黄色ﾏｰｶｰ2ヵ所",
"画面上で ②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TP軸合ﾏｰｸ追加",
"WETE-G002-A11"
]
} | {
"QualityItem": "合いﾏｰｸ記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの合いﾏｰｸが2箇所付いてること",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"調整治具",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整"
]
} | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "74±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5052",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"調整治具",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5052",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"調整治具",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す",
"4. 治具を取付ける"
],
"WorkPoints": [
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ",
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています",
"ﾊﾟﾜｰOFFにて締付の事",
"±0.05㎜以内(中央)±0.2㎜以内(左右)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの締付ﾄﾙｸ"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています",
"ﾊﾟﾜｰOFFにて締付の事",
"±0.05㎜以内(中央)±0.2㎜以内(左右)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの締付ﾄﾙｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"■安全作業",
"WETE-G002-A11"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFにて締付の事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの締付ﾄﾙｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し",
"2. 下段23Slotから上段23Slotへ移動し高さ確認"
],
"WorkPoints": [
"下段23Slot調整後すぐには原点復帰は決して行わ無い事原点高さが変わる場合があります"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"上段23Slot",
"補給部",
"NG排出部",
"補給部は内側を緩め調整",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"±0.05㎜以内(中央部) ±0.2㎜以内(左右)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"引き出部搬送面",
"ﾏｶﾞｼﾞﾝ側",
"FM-5519",
"FM-1934"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"上段23Slot",
"NG排出部",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"FM-1934",
"引き出部搬送面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"上段23Slot",
"補給部",
"NG排出部",
"補給部は内側を緩め調整",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"±0.05㎜以内(中央部) ±0.2㎜以内(左右)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"引き出部搬送面",
"ﾏｶﾞｼﾞﾝ側",
"FM-5519",
"FM-1934"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"上段23Slot",
"NG排出部",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"FM-1934",
"引き出部搬送面",
"WETE-G002-A11"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"上段23Slot",
"NG排出部",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"FM-1934",
"引き出部搬送面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"ｺﾞﾑｽﾄｯﾊﾟｰ",
"ﾎﾞｰﾙﾈｼﾞとｺﾞﾑｽﾄｯﾊﾟｰの干渉無い事",
"ﾎﾞｰﾙﾈｼﾞ",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事",
"O/Rｾﾝｻが遮光する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整治具",
"Size": "",
"ToolOther": "FM-6449",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6449",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"ｺﾞﾑｽﾄｯﾊﾟｰ",
"ﾎﾞｰﾙﾈｼﾞとｺﾞﾑｽﾄｯﾊﾟｰの干渉無い事",
"ﾎﾞｰﾙﾈｼﾞ",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事",
"O/Rｾﾝｻが遮光する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.1㎜で投光、原点で遮光する事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"ｺﾞﾑｽﾄｯﾊﾟｰ",
"ﾎﾞｰﾙﾈｼﾞとｺﾞﾑｽﾄｯﾊﾟｰの干渉無い事",
"ﾎﾞｰﾙﾈｼﾞ",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事",
"O/Rｾﾝｻが遮光する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"WETE-G002-A11"
]
} | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｽﾄｯﾊﾟｰとの干渉無き事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.