input stringclasses 1
value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-①(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. TP軸をﾊﾟﾜｰONする",
"2. ﾄﾚｲ本体の原点復帰",
"3. 引き出部を連結位置へ移動",
"4. 引き出部をNG排出部へ高さ位置を合わす",
"5. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かす"
],
"WorkPoints": [
"画面上で①②③④のﾎﾞﾀﾝを順次押... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [
"C~F間に0.3㎜のｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"LMｶﾞｲﾄﾞとの隙間が無い事をｼｯｸﾈｽｹﾞｰｼﾞで確認"... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.3㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩め... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行だし治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
"T... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "12.5㎜~13.0㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. TP軸原点復帰を行う",
"3. 吸着位置でﾚﾊﾞｰの確認を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"4. ﾊﾟﾜｰをOFF",
"■5. TP軸ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの増し締め"
],
"WorkPoints": [
"ﾊﾟﾚｯﾄをｶﾞｲﾄﾞに当付ける",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞに隙間が確保されていること"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾄﾚｲ本体のの原点復帰",
"2. 引き出部を連結位置へ移動",
"3. 引き出部をNG排出部へ移動",
"4. ﾊﾟﾚｯﾄ戻しへ移動",
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること",
"... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"LEDが点灯のこと(赤緑)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"LEDが点灯のこと(赤緑)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "40cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"LEDが点灯のこと(赤緑)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾄﾚｲ本体のの原点復帰",
"2. 引き出部を連結位置へ移動",
"3. 引き出部をNG排出部へ移動",
"4. ﾊﾟﾚｯﾄ戻しへ移動",
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること",
"再度動作をさせｾﾝｻの中心にあること",
... | {
"QualityItem": "光軸確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｾﾝｻの中心に投光状態である事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1.ﾊﾟﾚｯﾄ戻し位置でﾁｪｯｶｰの『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が 投光(水色)しているか確認する",
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動",
"3. 現在値の確認",
"2. TP軸ﾏﾆｭｱﾙ動作を押す",
"3. 現在値の確認",
"2. ... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1.ﾊﾟﾚｯﾄ戻し位置でﾁｪｯｶｰの『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が 投光(水色)しているか確認する",
"3. 現在値の確認",
"2. TP軸ﾏﾆｭｱﾙ動作を押す",
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動"
],
"WorkPoints": [
"現在値 -100.0... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1.ﾊﾟﾚｯﾄ戻し位置でﾁｪｯｶｰの『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が 投光(水色)しているか確認する",
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動",
"3. 現在値の確認",
"2. TP軸ﾏﾆｭｱﾙ動作を押す",
"3. 現在値の確認",
"2. ... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.33stで投光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.47st -99.53㎜位置まで移動"
],
"WorkPoints": [
"-99.53で点灯の場合はｾﾝｻをﾏｲﾅｽ側(矢印側)へ動かし消灯させる 消灯位置は安定した状態になるよう少しづつ移動させる事",
"･+0.47st -99.66~-99.53㎜の間で遮光(黒色... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"2. ｾﾝｻの固定を行う",
"3. 一連の調整完了後､再度ｾﾝｻの投光･遮光を確認"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Work... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.47st -99.53㎜位置まで移動"
],
"WorkPoints": [
"-99.53で点灯の場合はｾﾝｻをﾏｲﾅｽ側(矢印側)へ動かし消灯させる 消灯位置は安定した状態になるよう少しづつ移動させる事",
"･+0.47st -99.66~-99.53㎜の間で遮光(黒色... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.47stで遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かし､DOGに治具をｾｯﾄする",
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"矢印方向に当てつけ",
"ﾏｲﾅ... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"矢印方向に当てつけ",
"ﾏｲﾅｽ側O/Rｾﾝｻが-99.9㎜で投光､-100.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"ﾏｲﾅｽ側O/Rｾﾝｻが-99.9㎜で投光､-100.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"4. TP軸を動作させｾﾝｻ位置を調整する",
"1. TP軸の原点復帰を行う",
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かし､DOGに治具をｾｯﾄする"
],
"WorkPoints": [
"ﾏｲﾅｽ側O/Rｾﾝｻが-99.9㎜で投光､... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "規定ｽﾄﾛｰｸで投光・遮光している事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"3. 治具をDOGにｾｯﾄする",
"1. TP軸の原点復帰を行う",
"3. 治具をDOGにｾｯﾄする"
],
"WorkPoints": [
"矢印方向に当てつけ",
"矢印方向に当てつけ",
"+側O/Rｾﾝｻが40.9㎜で投光､... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"3. 治具をDOGにｾｯﾄする"
],
"WorkPoints": [
"矢印方向に当てつけ",
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [],
"WorkPoints": [
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"3. 治具をDOGにｾｯﾄする",
"2. 引き出部ｱｰﾑを吸着位置に動かす",
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)",
... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "規定ｽﾄﾛｰｸで投光・遮光している事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. ﾄﾚｲ本体の原点復帰",
"2. 引き出部を連結位置へ移動",
"3.ｽﾄｯﾊﾟ位置の調整",
"4.TTL軸と引き出し連結部の隙間確認を行う"
],
"WorkPoints": [
"ｽﾄｯﾊﾟをTTL軸ﾌﾟﾚｰﾄに当てつけ",
"黄丸部分に0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [],
"WorkPoints": [
"黄丸部分に0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"TTL軸ﾌﾟﾚｰﾄと連結部ｼｬﾌﾄ間",
"TTL軸ﾌﾟﾚｰﾄとｽﾄｯﾊﾟ間",
"接触面にはｸﾞﾘｰｽが塗布されているか確認の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝをｾｯﾄする",
"2. 治具をｾｯﾄする"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付ける",
"実際の治具色は同色です｡(ﾗﾍﾞﾙを確認)",
"投光用",
"遮光用",
"上下段に挿入",
"確認位置→補給部､上段23段目､下段23段目... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝをｾｯﾄする",
"2. 治具をｾｯﾄする"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付ける",
"上下段に挿入",
"確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "−99.9㎜で投光−100.0㎜で遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"3. ﾘﾌﾄ吸着位置へ上昇する"
],
"WorkP... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:補給部②:NGﾊﾟﾚｯﾄ③:ﾏｶ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:補給部... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが-99.9㎜で投光、-100.0㎜で遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoin... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoints":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoints": [],
... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "支持部にｸﾞﾘｰｽが塗布されている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝ(ﾄﾚｲﾊﾟﾚｯﾄ入り)をｾｯﾄする",
"2. TL軸･TP軸のｽﾋﾟｰﾄﾞを高速に切替",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"NG排出部及びﾏｶﾞｼﾞﾝの奇数段にﾄﾚｲﾊﾟﾚｯﾄがｾｯﾄされていること... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝ(ﾄﾚｲﾊﾟﾚｯﾄ入り)をｾｯﾄする",
"2. TL軸･TP軸のｽﾋﾟｰﾄﾞを高速に切替",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"NG排出部及びﾏｶﾞｼﾞﾝの奇数段にﾄﾚｲﾊﾟﾚｯﾄがｾｯﾄされていること",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"In... | {
"QualityItem": "点灯確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが不安定な動作をし無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "45cN･m",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"In... | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "16㎜赤消灯、緑点灯",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"In... | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "17㎜赤点灯、緑点灯",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認①",
"WorkItems": [
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認①",
"WorkItems": [
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",... | {
"QualityItem": "遮光確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "遮光状態である事",
"Method": "目視",
"RecordMethod": "WETE‐G002‐A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ有無ｾﾝｻ確認②",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"2. 原点復帰を行う",
"3. ﾘﾌ... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾊﾟﾚｯﾄ",
"Size": "",
"ToolOther": "MTKA010132AA",
"WorkName": "ﾊﾟﾚｯﾄ有無ｾﾝｻ確認②",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "有無確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが設定通り動作する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ",
"WorkItems": [
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"補給位置､NGﾊﾟﾚｯﾄ位置及びﾏｶﾞｼﾞﾝ全段数について全段数確認する事",
"高速になっている事を確認",
"動作中にﾊﾟﾚｯﾄの引っか... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝ(ﾄﾚｲﾊﾟﾚｯﾄ入り)をｾｯﾄする",
"2. TL軸･TP軸のｽﾋﾟｰﾄﾞを高速に切替",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"NG排出部及びﾏｶﾞｼﾞﾝの奇数段にﾄﾚｲﾊﾟﾚｯﾄがｾｯﾄされていること",
"補給位置､NGﾊﾟﾚｯﾄ位置及びﾏｶ... | {
"QualityItem": "搬送確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "引っ掛かり/異音が無い事",
"Method": "目視",
"RecordMethod": "WETE‐G002‐A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立①",
"WorkItems": [
"1. STAND に を圧入する",
"◆2. STAND に金ﾆｽを塗布する"
],
"WorkPoints": [
"※ﾋﾟﾝ圧入面と下面は塗布し無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:2.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立①",
"WorkItems": [
"1. STAND に を圧入する",
"◆2. STAND に金ﾆｽを塗布する"
],
"WorkPoints": [
"※ﾋﾟﾝ圧入面と下面は塗布し無い事",
"出代:2.5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ圧入面と下面は塗布し無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. に を で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う",
"◆4. 3完成品取付け面に金ﾆｽを塗布する"
],
"WorkPoints": [
"基準側(KB側)",
"従動側",
"1.基準面をﾋﾟﾝに押し当てて取付ける",
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. に を で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う",
"◆4. 3完成品取付け面に金ﾆｽを塗布する"
],
"WorkPoints": [
"基準側(KB側)",
"従動側",
"1.基準面をﾋﾟﾝに押し当てて取付ける",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "78㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. に を で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う"
],
"WorkPoints": [
"1.基準面をﾋﾟﾝに押し当てて取付ける",
"2.従動側を仮止めする",
"3.LMｶﾞｲﾄﾞ両終端に抜け防止治具を取... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "78.0㎜±0.01㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. に を で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う"
],
"WorkPoints": [
"1.基準面をﾋﾟﾝに押し当てて取付ける",
"2.従動側を仮止めする",
"3.LMｶﾞｲﾄﾞ両終端に抜け防... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "ｽﾄﾛｰｸ110㎜で0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. に を で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う",
"◆4. 3完成品取付け面に金ﾆｽを塗布する"
],
"WorkPoints": [
"基準側(KB側)",
"従動側",
"1.基準面をﾋﾟﾝに押し当てて取付ける",
... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立③",
"WorkItems": [
"1. に を取付ける",
"2. 1.完成品を のLMｽﾗｲﾀﾞｰに圧入する"
],
"WorkPoints": [
"4ｾｯﾄ組立",
"4箇所",
"半球側をｽﾗｲﾀﾞｰｸﾞﾘｰｽ注入部に圧入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立④",
"WorkItems": [
"1. に を取付ける",
"2. 1.完成品を のｽﾗｲﾀﾞｰﾆｯﾌﾟﾙに挿し込む"
],
"WorkPoints": [
"2ｾｯﾄ組立"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立①",
"WorkItems": [
"1. の取付け面にｱﾙｶﾝｻｽをかける",
"2. 1完成品に を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立②",
"WorkItems": [
"◆1. をｸﾞﾘｰｽｱｯﾌﾟする",
"2. に1完成品と を組込む"
],
"WorkPoints": [
" ﾍﾞｱﾘﾝｸﾞは背面合わせの事(下図参照)",
"断面図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の20%程度",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立②",
"WorkItems": [
"◆1. をｸﾞﾘｰｽｱｯﾌﾟする",
"2. に1完成品と を組込む"
],
"WorkPoints": [
" ﾍﾞｱﾘﾝｸﾞは背面合わせの事(下図参照)",
"断面図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾍﾞｱﾘﾝｸﾞ背面合わせ",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "1.27㎜",
"ToolOther": "2.5±0.2N･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立③",
"WorkItems": [
"3. 2完成品に を取付ける",
"4. 3完成品に を で取付ける"
],
"WorkPoints": [
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"W... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N･m±0.2N･m",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾋﾟｽﾄﾝ側面に塗布小豆:3",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀIEL/V",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾘﾝｸﾞ全体に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀIEL/V",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-057"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘﾝﾀﾞ摺動部内壁に塗布小豆:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀIEL/V",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立⑤",
"WorkItems": [
"2. に の順で取付け で締付ける",
"1. の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. 2完成品をVﾌﾞﾛｯｸにｾｯﾄして､芯ﾌﾞﾚを測定する"
],
"WorkPoints": [
"断面図",
"ｽﾌﾟﾗｲﾝｼｬﾌﾄが抜けないようにｲﾝｼｭﾛｯｸで結束する (2本)",
"ｽﾌﾟﾗｲﾝｼｬ... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立⑤",
"WorkItems": [
"2. に の順で取付け で締付ける",
"1. の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. 2完成品をVﾌﾞﾛｯｸにｾｯﾄして､芯ﾌﾞﾚを測定する"
],
"WorkPoints": [
"断面図",
"ｽﾌﾟﾗｲﾝｼｬﾌﾄが抜けないようにｲﾝｼｭﾛｯｸで結束する (2本)",
"ｽﾌﾟﾗｲﾝｼｬ... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立⑤",
"WorkItems": [
"3. 2完成品をVﾌﾞﾛｯｸにｾｯﾄして､芯ﾌﾞﾚを測定する"
],
"WorkPoints": [
"ｽﾌﾟﾗｲﾝｼｬﾌﾄの先端部を測定する",
"芯振れ:0.012㎜以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.012㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "1.2~1.6cN･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立⑥",
"WorkItems": [],
"WorkPoints": [
"回転ﾄﾙｸが 1.2cN･m ~ 1.6cN･m になるように NUT を締め込んで BOLT でﾛｯｸする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "回転ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "1.2cN･m~1.6cN･m",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組込み",
"WorkItems": [
"1. に を で取付ける"
],
"WorkPoints": [
" を左側に押し当てて取付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押し当て",
"押し当て... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"■1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"3. 1完成品にLABEL TERMINAL PROCESS を取付け､ を で取付ける",
"4. 3完成品に2完成品を で取付ける"
],
"WorkPoints": [
"断面図",
" ... | {
"QualityItem": "①の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"■1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"3. 1完成品にLABEL TERMINAL PROCESS を取付け､ を で取付ける",
"4. 3完成品に2完成品を で取付ける"
],
"WorkPoints": [
"断面図",
" ... | {
"QualityItem": "①の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"■1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"3. 1完成品にLABEL TERMINAL PROCESS を取付け､ を で取付ける",
"4. 3完成品に2完成品を で取付ける"
],
"WorkPoints": [
"断面図",
" ... | {
"QualityItem": "③の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"■1. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"3. 1完成品にLABEL TERMINAL PROCESS を取付け､ を で取付ける",
"4. 3完成品に2完成品を で取付ける"
],
"WorkPoints": [
"断面図",
" ... | {
"QualityItem": "③の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [],
"WorkPoints": [
"断面図",
" ﾓｰﾀｰｼｬﾌﾄ先端出代:3.3±0.2㎜",
"型式確認､ｼﾘｱﾙNo.",
"ﾎﾞﾙﾄ締付け位置注意する事",
" 付属ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:3.3㎜±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立②",
"WorkItems": [
"1. に を で取付ける"
],
"WorkPoints": [
"断面図",
"仮締め:SD-A044467-027にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組込み",
"WorkItems": [
"1. に を で取付ける"
],
"WorkPoints": [
"ﾎﾞﾙﾄ締付け位置注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"◆4. にｸﾞﾘｰｽを充填する",
"◆1. に油砥石をかけ､金ﾆｽを塗布する",
"2. 1完成品に を で取付ける",
"3. に を で取付ける",
"5. 2完成品に4完成品を挿入し､ で取付ける"
],
"WorkPoints": [
"5mm程度",
"正面合わせにて挿入する",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "下面・左面は塗布しない",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"◆4. にｸﾞﾘｰｽを充填する",
"◆1. に油砥石をかけ､金ﾆｽを塗布する",
"2. 1完成品に を で取付ける",
"3. に を で取付ける",
"5. 2完成品に4完成品を挿入し､ で取付ける"
],
"WorkPoints": [
"5mm程度",
"正面合わせにて挿入する",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の20%程度",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"◆4. にｸﾞﾘｰｽを充填する",
"◆1. に油砥石をかけ､金ﾆｽを塗布する",
"2. 1完成品に を で取付ける",
"3. に を で取付ける",
"5. 2完成品に4完成品を挿入し､ で取付ける"
],
"WorkPoints": [
"5mm程度",
"正面合わせにて挿入する",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立②",
"WorkItems": [
"2. に を挿入する",
"3. 2完成品に を挿入する",
"4. 3完成品に を挿入し締付ける",
"5. 付属のｾｯﾄﾋﾟｰｽ､ｾｯﾄﾋﾞｽで固定する",
"1. の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 7.5N･m... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.