input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ取付位置確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾟﾚｰﾄ取付位置確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "昇降ｾﾝｻｰ・ﾄﾞｸﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-2982",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ連結-①",
"WorkItems": [
"1. （ ）に㉖を挿入して可動プレートとシリンダーを芯出しする"
],
"WorkPoints": [
"㉖がスムーズに摺動する事",
"仮止めﾎﾞﾙﾄを締結する",
"黄色点線部のｼﾘﾝﾀﾞｰを前後左右に微調整し芯出しを行う",
"締結後は再度㉖が上下にスムーズに摺動する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2982",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ連結-①",
"WorkItems": [
"1. （ ）に㉖を挿入して可動プレートとシリンダーを芯出しする"
],
"WorkPoints": [
"㉖がスムーズに摺動する事",
"仮止めﾎﾞﾙﾄを締結する",
"黄色点線部のｼﾘﾝﾀﾞｰを前後左右に微調整し芯出しを行う",
"締結後は再度㉖が上下にスムーズに摺動する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾁｪｯｶｰ操作・設定説明",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ連結-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ連結-③",
"WorkItems": [
"3. WASHER CYL-NUT を ( )に取付､ｼﾘﾝﾀﾞｰﾅｯﾄの位置を調整する",
"◆1. WASHER に㉖を塗布する",
"◆2. CYL-NUT に㉖を塗布する"
],
"WorkPoints": [
"両面に㉖を塗布する事（黄色部）",
"25㎜上昇",
"黄色部のみに塗布する事",
"上昇ﾊﾞﾙﾌﾞの蓋を開け上昇ｽｲｯﾁを何度か押し､ｽﾃｰｼﾞを25㎜程度上昇させる事",
"ｼﾘﾝﾀﾞｰｼｬﾌﾄの干渉に注意する事",
"ｼﾘﾝﾀﾞｰﾅｯﾄ上面とｼﾘﾝﾀﾞｰﾅｯﾄ先端の距離を4.5±0.2㎜に調整する"
],
"Tolks": [
"締付ﾄﾙｸ 30N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上昇ｽｲｯﾁ",
"隙間が狭い方",
"上昇ﾊﾞﾙﾌﾞ",
"4.5㎜",
"ｸﾞﾘｰｽ塗布 小豆:1",
"ｸﾞﾘｰｽ塗布 小豆:1",
"検査表WASHER :ｼﾘﾝﾀﾞｰﾅｯﾄ取付位置確認"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ連結-③",
"WorkItems": [
"◆2. CYL-NUT に㉖を塗布する"
],
"WorkPoints": [
"黄色部のみに塗布する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ連結-③",
"WorkItems": [
"◆2. CYL-NUT に㉖を塗布する"
],
"WorkPoints": [
"黄色部のみに塗布する事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C05",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"◆作業者安全作業",
"WETE-G002-C05"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "4.5±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "36㎜",
"ToolOther": "30N･m",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ連結-③",
"WorkItems": [
"◆2. CYL-NUT に㉖を塗布する"
],
"WorkPoints": [
"黄色部のみに塗布する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-①",
"WorkItems": [
"1. ( )に をBOLT で仮付けする"
],
"WorkPoints": [
" の取付方向に注意する事(座ｸﾞﾘ側を外側に向ける)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｻﾞｸﾞﾘ面",
"仮止め:SD-A052011-054にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ側面ﾌﾟﾚｰﾄ位置決めｼﾞｸﾞ(ｼﾝｸﾞﾙ)",
"Size": "",
"ToolOther": "FM-6573",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6573",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "上ﾌﾟﾚｰﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6515",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6515",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "48.5±0.1㎜107.5±0.05㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ(NPM-W)",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-③",
"WorkItems": [
"1. （ ）に㉖を前後に取付ける",
"2. ( )を上昇させる"
],
"WorkPoints": [
"ｽﾃｰｼﾞは下限ONの状態の事",
"プレートと㉖の端面を合わせる事",
"㉖上昇ストッパーと のプレートに隙間が無い事（0.01㎜が通ら無い事）"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"620㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-③",
"WorkItems": [
"1. （ ）に㉖を前後に取付ける",
"2. ( )を上昇させる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0~+0.01㎜以内0~+0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰ側面ﾌﾟﾚｰﾄ位置決め治具(ﾌﾚｷｼﾌﾞﾙ)",
"Size": "",
"ToolOther": "FM-2675",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2675",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "上ﾌﾟﾚｰﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6515",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6515",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "48.5±0.1㎜107.5±0.05㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "48.5±0.1㎜107.5±0.05㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "±0.02㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.0~+0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付調整-⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ取付",
"WorkItems": [
"1. ( )に を仮付けする"
],
"WorkPoints": [
" の取付位置を間違えない様に注意して取付ける事(各20箇所)",
"㉖で軽く回転しない程度に固定する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A052011-058にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ(NPM-W)",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ調整検査-①",
"WorkItems": [
"1. （ ）に㉖をサイドプレートの前後に取付ける"
],
"WorkPoints": [
"ｽﾃｰｼﾞは下限ONの状態の事",
"前側は プレートと㉖の端面を合わせる事",
"後側は㉖の前側の位置より620㎜の位置に取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ調整検査-①",
"WorkItems": [
"1. （ ）に㉖をサイドプレートの前後に取付ける"
],
"WorkPoints": [
"ｽﾃｰｼﾞは下限ONの状態の事",
"前側は プレートと㉖の端面を合わせる事",
"後側は㉖の前側の位置より620㎜の位置に取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ調整検査-①",
"WorkItems": [
"2. を上昇させる"
],
"WorkPoints": [
"前後の㉖上昇ストッパーと のプレートに隙間が無い事（0.01㎜が通ら無い事）（４箇所）"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"620㎜"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受ﾌﾟﾚｰﾄ搭載面調整治具",
"Size": "300㎜",
"ToolOther": "FM-4639",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ調整検査-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4639",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ調整検査-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "2.500±0.025㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ調整検査-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "2.500-0.020~-0.060㎜2.500-0.040~-0.090㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "10㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻﾎﾟｰﾄﾎﾞﾙﾄ調整検査-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付",
"WorkItems": [
"1. ( )に をBOLT で取付ける",
"2. ( )にGUIDE をBOLT で取付ける",
"3. ( )に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾋﾟﾝに押し当て取付ける事(0.05㎜が通ら無い事)",
"矢印方向に押し当て取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付",
"WorkItems": [],
"WorkPoints": [
" ( )のﾋﾟﾝに押し当て取付ける事(0.05㎜が通ら無い事)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付",
"WorkItems": [
"1. ( )に をBOLT で取付ける",
"2. ( )にGUIDE をBOLT で取付ける",
"3. ( )に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾋﾟﾝに押し当て取付ける事(0.05㎜が通ら無い事)",
" ( )のﾋﾟﾝに押し当て取付ける事(0.05㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "I/Oﾁｪｯｸ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "I/Oﾁｪｯｸ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻｰ遮光時LEDが消灯する事",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｴｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "ｴｰｼﾞﾝｸﾞ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾁｪｯｶｰ操作・設定説明",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ( )に安全対策を行う"
],
"WorkPoints": [
"囲い等の安全対策を行い手が触れない様にする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"2. 基板ﾎﾙﾀﾞｰのｴｰｼﾞﾝｸﾞを行う",
"1. ( )に安全対策を行う"
],
"WorkPoints": [
"機種:NPM-GW､ﾚｰﾝ:ｼﾝｸﾞﾙになっている事を確認する",
"規格値:2000cycle動作でｴﾗｰ無き事",
"㉖のモードをエージングモードに切り替える",
"囲い等の安全対策を行い手が触れない様にする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｴｰｼﾞﾝｸﾞ動作実施",
"WETE-G002-C05"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "2000cycle動作でｴﾗｰ無き事",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "基板下受け上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "低速動作Ⓒ下降側:1.10s~1.14sⒹ上昇側:1.58s~1.62s高速動作Ⓐ下降側:0.90s~0.94sⒷ上昇側:実施しない",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｴｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "基板下受け上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "低速動作Ⓒ下降側:1.10s~1.14sⒹ上昇側:1.58s~1.62s高速動作Ⓐ下降側:0.90s~0.94sⒷ上昇側:実施しない",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受け上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C05"
]
} | {
"QualityItem": "ｽﾋﾟｰﾄﾞ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "低速動作Ⓒ下降側:1.10s~1.14sⒹ上昇側:1.58s~1.62s高速動作Ⓐ下降側:0.90s~0.94sⒷ上昇側:実施しない",
"Method": "目視",
"RecordMethod": "WETE-G002-C05",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｴｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "治具取り外し",
"WorkItems": [
"1. （ ）取付けている㉗エージング用ウエイト治具を取り外す",
"2. （ ）取付けている㉘基板ホルダーストッパーを取り外す",
"3. （ ）取付けている㉖基板ホルダーユニットチェッカーの配線配管を取り外す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞﾕﾆｯﾄｽﾄｯﾊﾟｰｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6140",
"WorkName": "治具取り外し",
"WorkItems": [
"1. （ ）取付けている㉗エージング用ウエイト治具を取り外す",
"2. （ ）取付けている㉘基板ホルダーストッパーを取り外す",
"3. （ ）取付けている㉖基板ホルダーユニットチェッカーの配線配管を取り外す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6140",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "治具取り外し",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾕﾆｯﾄｼﾘｱﾙ№LABEL貼付",
"WorkItems": [
"1. ( )に⑥を貼付ける"
],
"WorkPoints": [
"検査項目が全て完了している事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5㎜",
"左寄せに取付ける事"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し部品",
"WorkItems": [
"1. H1前準備工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出しされている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "支柱組立",
"WorkItems": [
"2. SPACER ﾍSCREW をねじ込む",
"1. SPACER SPACER の両端に油砥石をかける",
"2. SPACER へSCREW を締め込む"
],
"WorkPoints": [
"ﾄﾞﾝ突きの状態まで締結する",
"ﾄﾞﾝ突きの状態まで締結する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締結後のﾏｰｶｰはSCREW の内側にﾁｪｯｸすること(ﾈｼﾞ部分に塗らないこと)",
"砥石をかける",
"砥石をかける",
"締結後のﾏｰｶｰはSCREW の内側にﾁｪｯｸすること(ﾈｼﾞ部分に塗らないこと)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "締め切り",
"Method": "目視",
"RecordMethod": "",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"1. CYLINDER の固定とJOINT の取付け",
"◆2. CYLINDER にCYL-NUT を取付け"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ側面とｼﾘﾝﾀﾞｰのｶｯﾄ面を平行に取付ける",
"3.5㎜~4.0㎜",
"ﾌﾟﾚｰﾄは丸い面が上",
"CYL-NUT の上面に米粒大のｸﾞﾘｰｽを塗布する",
"注)一度締めたｼﾞｮｲﾝﾄは緩め無い事｡(緩めた場合は一度外しｼｰﾙﾃｰﾌﾟを巻きもう一度締め直す)",
"ｼﾘﾝﾀﾞｰを治具にｾｯﾄし付属のﾌﾟﾚｰﾄとﾅｯﾄで締結",
"※ｼｬﾌﾄに付いている標準ﾅｯﾄは不要"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"両面油砥石をかける",
"ﾌﾟﾚｰﾄ側面",
"ｼﾘﾝﾀﾞｰのｶｯﾄ面",
"ｼｰﾙﾃｰﾌﾟのｶｽはｴｱｰで除去",
"上面に油砥石をかける",
"ｸﾞﾘｰｽ塗布 米粒:1",
"ｼｰﾙﾃｰﾌﾟのｶｽは取り除いておくこと"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:1",
"Method": "目視",
"RecordMethod": "",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰﾅｯﾄ締付治具",
"Size": "",
"ToolOther": "FM-2984",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"1. CYLINDER の固定とJOINT の取付け",
"◆2. CYLINDER にCYL-NUT を取付け"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄは丸い面が上",
"CYL-NUT の上面に米粒大のｸﾞﾘｰｽを塗布する",
"ｼﾘﾝﾀﾞｰを治具にｾｯﾄし付属のﾌﾟﾚｰﾄとﾅｯﾄで締結",
"※ｼｬﾌﾄに付いている標準ﾅｯﾄは不要"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"両面油砥石をかける",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2984",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"1. CYLINDER の固定とJOINT の取付け",
"◆2. CYLINDER にCYL-NUT を取付け"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄは丸い面が上",
"CYL-NUT の上面に米粒大のｸﾞﾘｰｽを塗布する",
"ｼﾘﾝﾀﾞｰを治具にｾｯﾄし付属のﾌﾟﾚｰﾄとﾅｯﾄで締結",
"※ｼｬﾌﾄに付いている標準ﾅｯﾄは不要"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"両面油砥石をかける",
"◆作業者安全作業"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3.5~4.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "交換ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"1. CYLINDER の固定とJOINT の取付け",
"◆2. CYLINDER にCYL-NUT を取付け"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ側面とｼﾘﾝﾀﾞｰのｶｯﾄ面を平行に取付ける",
"ﾌﾟﾚｰﾄは丸い面が下",
"3.5㎜~4.0㎜",
"CYL-NUT の上面に米粒大のｸﾞﾘｰｽを塗布する",
"注)一度締めたｼﾞｮｲﾝﾄは緩め無い事｡(緩めた場合は一度外しｼｰﾙﾃｰﾌﾟを巻きもう一度締め直す)",
"後工程で取り外す為奥まで入れない｡",
"ｼﾘﾝﾀﾞｰを治具にｾｯﾄし付属のﾌﾟﾚｰﾄとﾅｯﾄで締結",
"※ｼｬﾌﾄに付いている標準ﾅｯﾄは不要"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"両面油砥石をかける",
"ﾌﾟﾚｰﾄ側面",
"ｼﾘﾝﾀﾞｰのｶｯﾄ面",
"ｼｰﾙﾃｰﾌﾟのｶｽはｴｱｰで除去",
"綺麗な面を上にして上面に油砥石をかける",
"ｸﾞﾘｰｽ塗布 米粒:1",
"ｼｰﾙﾃｰﾌﾟのｶｽは取り除いておくこと",
"治具を中に入れる",
"FM-2984"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰﾅｯﾄ締付治具",
"Size": "",
"ToolOther": "FM-2984",
"WorkName": "交換ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"1. CYLINDER の固定とJOINT の取付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを治具にｾｯﾄし付属のﾌﾟﾚｰﾄとﾅｯﾄで締結",
"※ｼｬﾌﾄに付いている標準ﾅｯﾄは不要"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"両面油砥石をかける",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2984",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "交換ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"1. CYLINDER の固定とJOINT の取付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを治具にｾｯﾄし付属のﾌﾟﾚｰﾄとﾅｯﾄで締結",
"※ｼｬﾌﾄに付いている標準ﾅｯﾄは不要"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"両面油砥石をかける",
"◆作業者安全作業"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3.5~4.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "上限下限ｾﾝｻｰ組立",
"WorkItems": [
"1. BOLT へWASHER WASHER を通しSENSOR SPACER PLATE を取付",
"2. ｺﾈｸﾀ部分にLABEL を取付け"
],
"WorkPoints": [
"定盤の上にｾﾝｻｰを当てつけた状態で締結する",
"ｺﾈｸﾀｰが右の時 ﾗﾍﾞﾙの表示が正面"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"文字があるほうを上"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上限下限ｾﾝｻｰ組立",
"WorkItems": [
"1. BOLT へWASHER WASHER を通しSENSOR SPACER PLATE を取付",
"2. ｺﾈｸﾀ部分にLABEL を取付け"
],
"WorkPoints": [
"定盤の上にｾﾝｻｰを当てつけた状態で締結する",
"ｺﾈｸﾀｰが右の時 ﾗﾍﾞﾙの表示が正面"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"文字があるほうを上"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "交換ﾌﾟﾚｰﾄ上限ｾﾝｻｰ支柱組立",
"WorkItems": [
"1. SPACER へSCREW を締結",
"2. SHAFT へWASHER をBOLT で締結"
],
"WorkPoints": [
"ﾄﾞﾝ突きの状態まで締めこむ｡",
"ﾀｯﾌﾟ穴深さが安定しない為出代確認"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M5×12",
"M4×16",
"Hｶｯﾄ"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "6~7㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "交換ﾌﾟﾚｰﾄ上限ｾﾝｻｰ支柱組立",
"WorkItems": [
"1. SPACER へSCREW を締結",
"2. SHAFT へWASHER をBOLT で締結"
],
"WorkPoints": [
"ﾄﾞﾝ突きの状態まで締めこむ｡",
"ﾀｯﾌﾟ穴深さが安定しない為出代確認"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M5×12",
"M4×16",
"Hｶｯﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "交換上限ｾﾝｻｰ組立",
"WorkItems": [
"1. PLATE へSENSOR をBOLT WASHER WASHER で締結",
"2. ③を取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀｰが左の時､ﾗﾍﾞﾙの表示が正面になる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"50mm",
"ｾﾝｻｰを矢印方向に押当てすること"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "交換上限ｾﾝｻｰ組立",
"WorkItems": [
"1. PLATE へSENSOR をBOLT WASHER WASHER で締結",
"2. ③を取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀｰが左の時､ﾗﾍﾞﾙの表示が正面になる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"50mm",
"ｾﾝｻｰを矢印方向に押当てすること"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:50㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾞｮｲﾝﾄﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET BRACKET BRACKET にLABEL を貼付ける",
"2. BRACKET にJOINT JOINT を取付ける",
"1. BRACKET BRACKET BRACKET にLABEL を貼付ける",
"2. BRACKET にJOINT JOINT を取付ける"
],
"WorkPoints": [
"13㎜",
"13㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第一実装ｽﾃｰｼﾞ:1B1233P",
"第二実装ｽﾃｰｼﾞ:1B1234P",
"25mm",
"10mm",
"12mm",
"6mm",
"第一実装ｽﾃｰｼﾞ a:B1244R",
"第一実装ｽﾃｰｼﾞ b:B1245R",
"第二実装ｽﾃｰｼﾞ a:B1235R",
"第二実装ｽﾃｰｼﾞ b:B1236R",
"第一実装ｽﾃｰｼﾞ a:B1140R",
"第一実装ｽﾃｰｼﾞ b:B1233R",
"JOINTの出代",
"第一実装ｽﾃｰｼﾞ:1B1233P",
"第二実装ｽﾃｰｼﾞ:1B1234P",
"25mm",
"10mm",
"12mm",
"6mm",
"第一実装ｽﾃｰｼﾞ a:B1244R",
"第一実装ｽﾃｰｼﾞ b:B1245R",
"第二実装ｽﾃｰｼﾞ a:B1235R",
"第二実装ｽﾃｰｼﾞ b:B1236R",
"第一実装ｽﾃｰｼﾞ a:B1140R",
"第一実装ｽﾃｰｼﾞ b:B1233R",
"JOINTの出代"
]
} | {
"QualityItem": "出代確認貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:13㎜寸法の位置に貼付てある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ有り無しｾﾝｻｰ組立",
"WorkItems": [],
"WorkPoints": [
"ｾﾝｻｰとPLATEの溝を合わせ取付る",
"ｲﾝｼｭﾛｯｸ固定にて配線がﾌﾞﾗｹｯﾄのｴｯｼﾞに干渉し無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B1140R (第一実装ｽﾃｰｼﾞ)",
"B1141R (第二実装ｽﾃｰｼﾞ)",
"ｺﾈｸﾀｰ左時 表示正面",
"ｺﾈｸﾀｰ右時 表示正面",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"配線",
"配線"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ有り無しｾﾝｻｰ組立",
"WorkItems": [
"1. PLATE へSENSOR をBOLT WASHER WASHER で取付､配線を引き回す",
"2. を取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄに対し傾き無い事",
"切り欠き部を避け配線を引廻す"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"50mm",
"40mm",
"ｾﾝｻｰを矢印方向に押当てること"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付てある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "下受け上下ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. VALVE へSPEED-CONTROLLER JOINT JOINT を取付"
],
"WorkPoints": [
"JOINT の取付け寸法",
"3.5~4.0㎜",
"ｺﾞﾐ防止の為､全閉にしておく事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3.5㎜~4.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.0N･m",
"WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. MANIFOLD にSPEED-CONTROLLER SPEED-CONTROLLER と付属のﾏﾌﾗｰを取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Ф4",
"Ф6"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.0N･m",
"WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. MANIFOLD にSPEED-CONTROLLER SPEED-CONTROLLER と付属のﾏﾌﾗｰを取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Ф4",
"Ф6"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.5N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾌﾞｯｼｭｸﾞﾘｰｽｱｯﾌﾟ",
"WorkItems": [
"◆1. LINEAR-BUSH の内側のﾎﾞｰﾙ部にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆中のﾎﾞｰﾙ部にｸﾞﾘｰｽ塗布",
"◆表面にｸﾞﾘｰｽ塗布",
"･LINEAR-BUSH を開封し､油を拭き取ること",
"･LINEAR-BUSH の表面に薄くｸﾞﾘｰｽを塗布すること",
"･ｺﾞﾐなどが付着しないように注意すること",
"･表面全体にｸﾞﾘｰｽを塗布する (小豆/1粒)",
"･ﾘﾆｱ内部にｸﾞﾘｰｽを塗布(上下) ﾎﾞｰﾙﾍﾞｱﾘﾝｸﾞが埋まる程度に 塗付し､余りは除去する｡",
"片側40mm程度",
"ｸﾞﾘｰｽ塗布 小豆:1"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾁｭｰﾌﾞ長片側40㎜小豆1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-①",
"WorkItems": [
"1. ㉖の本体エアー配管を工場エアー配管に接続する",
"3. ㉖の圧力計を確認または調整する",
"2. ㉖のエアーバルブを開にする"
],
"WorkPoints": [
"設定圧力:0.50Mpa±0.05",
"ﾊﾝﾄﾞﾙ",
"ﾛｯｸﾅｯﾄ",
"圧力調整はロックナットを㉗で緩め、ハンドルで増減させる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ注入機を使用する場合のみ参照のこと"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "0.50Mpa±0.05",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙはかり",
"Size": "",
"ToolOther": "EK-3000i",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-②",
"WorkItems": [
"3. 1完成品を㉖に乗せ、ゼロ設定する",
"2. ㉖の電源を投入する",
"3. 1完成品を㉖に乗せ、ゼロ設定する",
"2. ㉖の電源を投入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-③",
"WorkItems": [
"◆1. を㉖にセットし、内側ボール内にグリースを塗布する"
],
"WorkPoints": [
" を素手で触ら無い事",
"Hｶｯﾄ面をｶﾞｲﾄﾞに合わせる",
"ｽﾄｯﾊﾟｰに当付ける",
"2秒以上ﾎﾞﾀﾝを長押しｸﾞﾘｰｽを塗布する(ｼﾘﾝﾀﾞｰが動かなくなるまで)",
"ｸﾞﾘｰｽが塗布される範囲",
"ｸﾞﾘｰｽ塗布後､ を引き抜く",
"ｽﾄｯﾊﾟｰに当付ける",
"ｸﾞﾘｰｽが塗布される範囲",
" を5回ほどｽﾄﾛｰｸさせ､ｸﾞﾘｰｽをなじませる",
"2秒以上ﾎﾞﾀﾝを長押しｸﾞﾘｰｽを塗布する(ｼﾘﾝﾀﾞｰが動かなくなるまで)",
"塗布済",
" を反転させ､反対側から挿入する",
"ﾎﾞｰﾙ部にｸﾞﾘｰｽが塗布されていることを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを8個製作",
"ｸﾞﾘｰｽ注入機でのｸﾞﾘｰｽ塗布作業時のみ参照"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り塗布出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙはかり",
"Size": "",
"ToolOther": "EK-3000i",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-④",
"WorkItems": [
"1. を㉖に乗せグリス塗布量を計測する"
],
"WorkPoints": [
" を素手で触ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ注入機でのｸﾞﾘｰｽ塗布作業時のみ参照",
"この作業では同じものを8個製作",
"ｸﾞﾘｰｽが目安量外の場合は手で塗布量を調整する不足の場合:ｸﾞﾘｰｽを注入する過度な場合:ｸﾞﾘｰｽを除去する",
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "5g~7g",
"Method": "ﾃﾞｼﾞﾀﾙはかり",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-④",
"WorkItems": [
"1. を㉖に乗せグリス塗布量を計測する",
"◆2. 1完成品の表面全体に㉗グリースを塗布する（黄色部）"
],
"WorkPoints": [
"ｺﾞﾐ等が付着してい無い事を確認する事",
"特にﾕﾆｯﾄ取付面にｺﾞﾐ等が付着してい無い事",
" を素手で触ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:2",
"ｸﾞﾘｰｽ注入機でのｸﾞﾘｰｽ塗布作業時のみ参照",
"この作業では同じものを8個製作",
"ｸﾞﾘｰｽ塗布: 5g ~ 7g",
"ｸﾞﾘｰｽが目安量外の場合は手で塗布量を調整する不足の場合:ｸﾞﾘｰｽを注入する過度な場合:ｸﾞﾘｰｽを除去する"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "下受け交換ﾘﾆｱﾌﾞｯｼｭｸﾞﾘｰｽｱｯﾌﾟ",
"WorkItems": [
"◆1. LINEAR-BUSH の内側のﾎﾞｰﾙ部にｸﾞﾘｰｽを塗布する｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･LINEAR-BUSH を開封し､油を拭き取ること",
"･LINEAR-BUSH の表面に薄くｸﾞﾘｰｽを塗布すること",
"･ｺﾞﾐなどが付着しないように注意すること",
"◆中のﾎﾞｰﾙ部にｸﾞﾘｰｽ塗布",
"◆表面にｸﾞﾘｰｽ塗布",
"･表面全体にｸﾞﾘｰｽを塗布する (小豆/半分)",
"･ﾘﾆｱ内部にｸﾞﾘｰｽを塗布(上下) ﾎﾞｰﾙﾍﾞｱﾘﾝｸﾞが埋まる程度に 塗付し､余りは除去する｡",
"30mm程度",
"ｸﾞﾘｰｽ塗布 小豆:0.5"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾁｭｰﾌﾞ長30㎜小豆1/2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.5N･m",
"WorkName": "下受けﾌﾟﾚｰﾄｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"1. STOPPER BRACKET WASHER をBOLT WASHER NUT で取付"
],
"WorkPoints": [
"STOPPER の長穴部へWASHER を入れ⑪⑫⑬で締結し摺動を確認",
"BRACKET を 方向に押し当て A=B 位置で締結",
"全体の摺動に引っかかりがないことを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"約11mm",
"取付け方向に注意!この部品には方向性があります｡",
"締付ﾄﾙｸ 3.5N･m",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"◆2. POST NUT を取付け､SPRING をかける"
],
"WorkPoints": [
"BRACKET のｽﾌﾟﾘﾝｸﾞを引っ掛ける部分(溝加工)にｸﾞﾘｰｽ塗布する",
"約17㎜",
"ｽﾌﾟﾘﾝｸﾞ掛け方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｽﾌﾟﾘﾝｸﾞとｴｯｼﾞ部との接触部へ米粒大のｸﾞﾘｰｽ塗布",
"※付属のﾅｯﾄは 使用しない",
"ｸﾞﾘｰｽ塗布 米粒:1",
"◆作業者安全作業"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:17㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"1. STOPPER BRACKET WASHER をBOLT WASHER NUT で取付",
"◆2. POST NUT を取付け､SPRING をかける"
],
"WorkPoints": [
"STOPPER の長穴部へWASHER を入れ⑪⑫⑬で締結し摺動を確認",
"BRACKET を 方向に押し当て A=B 位置で締結",
"全体の摺動に引っかかりがないことを確認する",
"BRACKET のｽﾌﾟﾘﾝｸﾞを引っ掛ける部分(溝加工)にｸﾞﾘｰｽ塗布する",
"約17㎜",
"ｽﾌﾟﾘﾝｸﾞ掛け方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｽﾌﾟﾘﾝｸﾞとｴｯｼﾞ部との接触部へ米粒大のｸﾞﾘｰｽ塗布",
"約11mm",
"※付属のﾅｯﾄは 使用しない",
"取付け方向に注意!この部品には方向性があります｡",
"締付ﾄﾙｸ 3.5N･m",
"ｸﾞﾘｰｽ塗布 米粒:1"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.5N･m",
"WorkName": "下受けﾌﾟﾚｰﾄ有り無しｾﾝｻｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M5×12 厚平W ﾅｯﾄ",
"締付ﾄﾙｸ 3.5N･m",
"ﾎﾞﾙﾄ中心で左右の振りが同じである事",
"ｸﾞﾘｰｽ塗布 米粒:1",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ有り無しｾﾝｻｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"◆1. DOG BRACKET WASHER をBOLT WASHER NUT で締結",
"2. 1の完成品をﾌﾞﾛｯｸとｽｺﾔで直角度を確認調整する",
"◆3. POST をNUT で取付け､SPRING をかける"
],
"WorkPoints": [
"WASHER へ米粒大ｸﾞﾘｰｽ塗布(摺動が悪くなる為塗布しすぎ注意)",
"全体の摺動に引っかかりがないことを確認する",
"BRACKET のｽﾌﾟﾘﾝｸﾞを引っ掛ける部分(溝加工)にｸﾞﾘｰｽ塗布する",
"約17㎜",
"BRACKET を→方向に押し当て A=B 位置で締結 (約21.5mm) 摺動を確認",
"DOG の長穴部へWASHER を入れBOLT WASHER NUT で締結"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M5×12 厚平W ﾅｯﾄ",
"締付ﾄﾙｸ 3.5N･m",
"ﾏｰｷﾝｸﾞ位置",
"ｽﾌﾟﾘﾝｸﾞとｴｯｼﾞ部との接触部へ米粒大のｸﾞﾘｰｽ塗布",
"※付属のﾅｯﾄは 使用しない",
"DOG ﾄﾞｸﾞのｶﾞﾀの振り分けｾﾝﾀｰが直角であること",
"ﾎﾞﾙﾄ中心で左右の振りが同じである事",
"ﾎﾞﾙﾄ",
"ｸﾞﾘｰｽ塗布 米粒:1",
"ｸﾞﾘｰｽ塗布 米粒:1"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ有り無しｾﾝｻｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"◆1. DOG BRACKET WASHER をBOLT WASHER NUT で締結",
"2. 1の完成品をﾌﾞﾛｯｸとｽｺﾔで直角度を確認調整する"
],
"WorkPoints": [
"WASHER へ米粒大ｸﾞﾘｰｽ塗布(摺動が悪くなる為塗布しすぎ注意)",
"BRACKET を→方向に押し当て A=B 位置で締結 (約21.5mm) 摺動を確認",
"DOG の長穴部へWASHER を入れBOLT WASHER NUT で締結"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "PINの出代17㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｺﾔ",
"Size": "",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ有り無しｾﾝｻｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"◆1. DOG BRACKET WASHER をBOLT WASHER NUT で締結",
"2. 1の完成品をﾌﾞﾛｯｸとｽｺﾔで直角度を確認調整する",
"◆3. POST をNUT で取付け､SPRING をかける"
],
"WorkPoints": [
"WASHER へ米粒大ｸﾞﾘｰｽ塗布(摺動が悪くなる為塗布しすぎ注意)",
"全体の摺動に引っかかりがないことを確認する",
"BRACKET のｽﾌﾟﾘﾝｸﾞを引っ掛ける部分(溝加工)にｸﾞﾘｰｽ塗布する",
"約17㎜",
"BRACKET を→方向に押し当て A=B 位置で締結 (約21.5mm) 摺動を確認",
"DOG の長穴部へWASHER を入れBOLT WASHER NUT で締結"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M5×12 厚平W ﾅｯﾄ",
"締付ﾄﾙｸ 3.5N･m",
"ﾏｰｷﾝｸﾞ位置",
"ｽﾌﾟﾘﾝｸﾞとｴｯｼﾞ部との接触部へ米粒大のｸﾞﾘｰｽ塗布",
"※付属のﾅｯﾄは 使用しない",
"DOG ﾄﾞｸﾞのｶﾞﾀの振り分けｾﾝﾀｰが直角であること",
"ﾎﾞﾙﾄ中心で左右の振りが同じである事",
"ﾎﾞﾙﾄ",
"ｸﾞﾘｰｽ塗布 米粒:1",
"ｸﾞﾘｰｽ塗布 米粒:1"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾄﾞｸﾞ取付角度確認",
"Method": "ｽｺﾔ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ精度確認・組立",
"WorkItems": [
"4. PLATE ﾌﾟﾚｰﾄにﾃｰﾌﾟ等で各4枚明示する"
],
"WorkPoints": [
"前後で規正位置(ｷｽﾞ)が異なる為",
"PLATE PIN については組立後ｽﾙｰ部品として保管すること"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"定盤"
]
} | {
"QualityItem": "平面度",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "平面度0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ精度確認・組立",
"WorkItems": [
"2. PLATE ﾌﾟﾚｰﾄを定盤上で平面度を測定する (9箇所)",
"3. PLATE ﾌﾟﾚｰﾄにBOLT WASHER を締結",
"4. PLATE ﾌﾟﾚｰﾄにﾃｰﾌﾟ等で各4枚明示する",
"5. 締結増締めﾁｪｯｸを行う",
"1. PLATE ﾌﾟﾚｰﾄのｴｯｼﾞ･ｷﾘ穴･ﾀｯﾌﾟ穴部分のﾊﾞﾘ･打痕がある場合取り除く"
],
"WorkPoints": [
"目立つ(大きな)ｷｽﾞ･打痕ありの場合使用しないこと",
"(PLATE ﾌﾟﾚｰﾄにBOLT WASHER 締結､入荷した場合､ PLATE ﾌﾟﾚｰﾄにBOLT WASHER が締結している事を確認する)取付位置右下(4枚とも同位置)",
"前後で規正位置(ｷｽﾞ)が異なる為",
"ﾁｪｯｸ後ﾏｰｶｰﾍﾟﾝでﾏｰｸ",
"ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄは原単位1となり発注4となる為､4ｾｯﾄ作成する",
"PLATE PIN については組立後ｽﾙｰ部品として保管すること"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"定盤",
"平面度 0.1mm以上の場合 使用禁止",
"M3×5 小径平W",
"第一ｽﾃｰｼｮﾝ前",
"第一ｽﾃｰｼｮﾝ前",
"第二ｽﾃｰｼｮﾝ後",
"第二ｽﾃｰｼｮﾝ前",
"第一ｽﾃｰｼｮﾝ後",
"ﾎﾞﾙﾄﾍﾟｲﾝﾄﾏｰｶｰ",
"ｴｱｰｼﾞｮｲﾝﾄﾍﾟｲﾝﾄﾏｰｶｰ",
"配線ｺﾈｸﾀｰ油性ﾏｼﾞｯｸ",
"組立者本人",
"第3者ﾁｪｯｸ",
"ﾎﾞﾙﾄ等締結後ﾏｰｷﾝｸﾞはこのﾍﾟｰｼﾞ以降は指示はありませんが実施すること",
"ﾁｪｯｸした本人が必ずﾏｰｷﾝｸﾞすること"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰ位置調整治具",
"Size": "",
"ToolOther": "FM-3047",
"WorkName": "下受け上下ﾌﾟﾚｰﾄ組立_1",
"WorkItems": [
"1. PLATE へSHAFT をBOLT WASHER で締結(仮取付)",
"2. PLATE へSPACER を置き をBOLT WASHER で締結"
],
"WorkPoints": [
"第一第二共に同じ形状の為､組立時に明確にしておくこと",
"M4×2が後側",
"M4×2が手前",
"ｼﾞｮｲﾝﾄが 外側を向くように取付",
"ﾌﾟﾚｰﾄ穴ｾﾝﾀｰにｼﾘﾝﾀﾞｰを取付",
"SD-0164023-049で本締結"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります｡",
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"第1.第2取付各4箇所で仮締結",
"下側から治具を通しｼﾘﾝﾀﾞｰ と穴の芯だしを行う",
"FM-3047"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3047",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "下受け上下ﾌﾟﾚｰﾄ組立_1",
"WorkItems": [],
"WorkPoints": [
"SD-0164023-049で本締結"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第1.第2取付各4箇所で仮締結",
"下側から治具を通しｼﾘﾝﾀﾞｰ と穴の芯だしを行う",
"FM-3047"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄｽﾄｯﾊﾟｰ高さ出しﾌﾞﾛｯｸ",
"Size": "",
"ToolOther": "FM-2795",
"WorkName": "下受け上下ﾌﾟﾚｰﾄ組立_2",
"WorkItems": [
"2. ﾌﾟﾚｰﾄをひっくり返し表面に をBOLT で締結",
"1. へBOLT とNUT を取付け、㉙を塗布する"
],
"WorkPoints": [
"㉖でBOLT の高さを合わせる",
"ﾈｼﾞ穴の中央で締結する",
"FM-2795",
"高さを合わせる",
"作業後､この面に防錆油を塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表面",
"下側",
"締付ﾄﾙｸ 3.5N･m"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "FM-2795",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "下受け上下ﾌﾟﾚｰﾄ組立_2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"裏面",
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N・m±10%3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付け_1",
"WorkItems": [
"1. へLABEL を貼付け"
],
"WorkPoints": [
"貼付け部分を脱脂する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付位置",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り張付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受ｶﾞｲﾄﾞ取付治具",
"Size": "",
"ToolOther": "FM-3053",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_1",
"WorkItems": [
"2. 治具を矢印の方向に押し当てで固定する",
"3. PLATE に治具を取付ける",
"1. GUIDE に㉗を取付る"
],
"WorkPoints": [
"下面､ﾋﾟﾝとも治具との隙間無きこと",
"上側に押し当てて取付ける｡",
"下側ﾀｯﾌﾟ有り",
"ｾｯﾄで対象方向から取付ける",
"ﾀｯﾌﾟ穴を下に向ける",
"こちらより挿入",
"こちらより挿入",
"治具への取付方向は写真を参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"固定ﾎﾞﾙﾄ",
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"ﾋﾟﾝを上へ押当",
"上へ押当",
"押当",
"押当",
"M4×12M4平W(治具用ﾎﾞﾙﾄ)",
"隙間無きこと",
"M4×12M4平W(治具用ﾎﾞﾙﾄ)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3053",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_2",
"WorkItems": [
"1. に をBOLT WASHER で取付ける",
"2. 1､の完成品にPLATE とGUIDE を仮置きする"
],
"WorkPoints": [
"矢印の方向に押し当て､ﾋﾟﾝと治具との隙間無きこと",
"PLATE を左側のみ固定する"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"第二実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"基準側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受ｶﾞｲﾄﾞ取付治具",
"Size": "",
"ToolOther": "FM-3053",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_2",
"WorkItems": [
"1. に をBOLT WASHER で取付ける",
"2. 1､の完成品にPLATE とGUIDE を仮置きする",
"3. 治具での位置決め固定"
],
"WorkPoints": [
"矢印の方向に押し当て､ﾋﾟﾝと治具との隙間無きこと",
"PLATE を左側のみ固定する",
"組立上裏返しで組立てる為表裏方向を図参照する",
"組立上裏返しで組立てる為PLATE はｻﾞｸﾞﾘ穴を下面にし各穴は下図参照のこと",
" の固定が出来たら㉘の治具をはずす",
"基準側A穴ｾﾝﾀｰに押し当てｶﾞﾀなしで､Bは穴ｾﾝﾀｰで固定する",
"Aを固定後Bを固定すること",
"下図参照に第一･第二実装ｽﾃｰｼﾞを組立てる事｡増し締めはSD-0164023-020にて実施"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"第二実装ｽﾃｰｼﾞ",
"第一実装ｽﾃｰｼﾞ",
"押し当て取付※隙間無き事",
"固定ﾎﾞﾙﾄ",
"押当",
"押当",
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"基準側",
"基準側",
"D-Pin位置決め ﾎﾞﾙﾄ固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3053",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受ｶﾞｲﾄﾞﾌﾟﾚｰﾄﾋﾟｯﾁ調整治具",
"Size": "",
"ToolOther": "FM-4134",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_2",
"WorkItems": [
"1. に をBOLT WASHER で取付ける",
"2. 1､の完成品にPLATE とGUIDE を仮置きする",
"3. 治具での位置決め固定"
],
"WorkPoints": [
"矢印の方向に押し当て､ﾋﾟﾝと治具との隙間無きこと",
"PLATE を左側のみ固定する",
"組立上裏返しで組立てる為表裏方向を図参照する",
"組立上裏返しで組立てる為PLATE はｻﾞｸﾞﾘ穴を下面にし各穴は下図参照のこと",
" の固定が出来たら㉘の治具をはずす",
"基準側A穴ｾﾝﾀｰに押し当てｶﾞﾀなしで､Bは穴ｾﾝﾀｰで固定する",
"Aを固定後Bを固定すること",
"下図参照に第一･第二実装ｽﾃｰｼﾞを組立てる事｡増し締めはSD-0164023-020にて実施"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"第二実装ｽﾃｰｼﾞ",
"第一実装ｽﾃｰｼﾞ",
"押し当て取付※隙間無き事",
"固定ﾎﾞﾙﾄ",
"押当",
"押当",
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"基準側",
"基準側",
"D-Pin位置決め ﾎﾞﾙﾄ固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4134",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受けｶﾞｲﾄﾞ取付治具",
"Size": "",
"ToolOther": "FM-3053",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_3",
"WorkItems": [
"1. に治具を取付て各部品の固定を行う",
"2. 治具から取外し定盤上でｶﾞﾀﾂｷが無い事確認する"
],
"WorkPoints": [
"治具に下当てした面を確認",
"㉙の治具をＤ-Pin基準に取付けて固定する",
"基準位置はﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬｰ取付側となる為固定後ﾏｰｷﾝｸﾞする事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"定盤",
"D-Pin位置決め ﾎﾞﾙﾄ固定",
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"ﾏｰｷﾝｸﾞ位置",
"基準側",
"基準側",
"完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3053",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受ｶﾞｲﾄﾞﾌﾟﾚｰﾄﾋﾟｯﾁ調整治具",
"Size": "",
"ToolOther": "FM-4134",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_3",
"WorkItems": [
"1. に治具を取付て各部品の固定を行う",
"2. 治具から取外し定盤上でｶﾞﾀﾂｷが無い事確認する"
],
"WorkPoints": [
"治具に下当てした面を確認",
"㉙の治具をＤ-Pin基準に取付けて固定する",
"基準位置はﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬｰ取付側となる為固定後ﾏｰｷﾝｸﾞする事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"定盤",
"D-Pin位置決め ﾎﾞﾙﾄ固定",
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"ﾏｰｷﾝｸﾞ位置",
"基準側",
"基準側",
"完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4134",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_3",
"WorkItems": [
"1. に治具を取付て各部品の固定を行う",
"2. 治具から取外し定盤上でｶﾞﾀﾂｷが無い事確認する"
],
"WorkPoints": [
"治具に下当てした面を確認",
"㉙の治具をＤ-Pin基準に取付けて固定する",
"基準位置はﾎﾞｰﾙﾌﾟﾗﾝｼﾞｬｰ取付側となる為固定後ﾏｰｷﾝｸﾞする事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"定盤",
"D-Pin位置決め ﾎﾞﾙﾄ固定",
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"ﾏｰｷﾝｸﾞ位置",
"基準側",
"基準側",
"完成品"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.