input stringclasses 1
value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_4",
"WorkItems": [],
"WorkPoints": [
"･ｽﾄｯﾊﾟｰ前後に0.2mmの隙間がある事を確認",
"中間ｽﾄｯﾊﾟｰとにﾌﾟﾚｰﾄを当てた状態で奥側のｽﾄｯﾊﾟｰを固定する｡再度ﾌﾟﾚｰﾄを出し入れし､奥側のｽﾄｯﾊﾟｰに当たった時､中間ｽﾄｯﾊﾟｰがばね圧で上昇することを確認する｡",
"･ｽﾄｯﾊﾟｰ前後に0.2mmの隙間がある事を確認",
"中... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.2㎜",
"ToolOther": "",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_4",
"WorkItems": [],
"WorkPoints": [
"･ｽﾄｯﾊﾟｰ前後に0.2mmの隙間がある事を確認",
"中間ｽﾄｯﾊﾟｰとにﾌﾟﾚｰﾄを当てた状態で奥側のｽﾄｯﾊﾟｰを固定する｡再度ﾌﾟﾚｰﾄを出し入れし､奥側のｽﾄｯﾊﾟｰに当たった時､中間ｽﾄｯﾊﾟｰがばね圧で上昇することを確認する｡"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜が入る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受平面度測定ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-4166",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_4",
"WorkItems": [
"1. PLATE にPIN をWASHER BOLT で取付ける｡",
"2. へPLATE をBOLT WASHER で裏側から仮取付け",
"3. にPLATE を仮に乗せ､ 下受平面度測定ﾌﾟﾚｰﾄを奥側にｾｯﾄしｽﾄｯﾊﾟｰを固定する",
"3. に をBOLT WASHER で取付ける｡ PLATE 治具をｾｯﾄし指でｽ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4166",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "下受平面度測定ﾌﾟﾚｰﾄ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.23.5N･m",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_5",
"WorkItems": [
"1. へWASHER WASHER をBOLT で締結する",
"2. 完成品の右側用にPLUNGER をNUT で締結"
],
"WorkPoints": [
"左側用(ﾜｯｼｬ 大)",
"左側用(ﾜｯｼｬ 大)",
"右側用(ﾜｯｼｬ 小)",
"右側用(ﾜｯｼｬ 小)",
"0.4~0.6mm... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "0.5N･m",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_5",
"WorkItems": [],
"WorkPoints": [
"ﾌﾟﾗﾝｼﾞｬｰは損防止のためﾅｯﾄを締付けてからの出代調整禁止"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.5N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_5",
"WorkItems": [],
"WorkPoints": [
"ﾌﾟﾗﾝｼﾞｬｰは損防止のためﾅｯﾄを締付けてからの出代調整禁止"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "出代:0.4~0.6㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受平面度測定ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-4166",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_6",
"WorkItems": [
"1. にPLATE を仮に乗せる｡"
],
"WorkPoints": [
"PLATE は治具をｾｯﾄする為に乗せるので固定しない｡固定はSD-0164023-024で固定する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "取付動作確認",
"ToolManageNo": "FM-4166",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付き動作する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.5N･m",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_7",
"WorkItems": [
"1. へ をSPACER BOLT WASHER にて締結"
],
"WorkPoints": [
"固定後､ が上下にｽﾑｰｽﾞな動作が出来ることを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受平面度測定ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-4166",
"WorkName": "下受け交換上下ﾌﾟﾚｰﾄ組立_7",
"WorkItems": [
"1. へ をSPACER BOLT WASHER にて締結",
"2. ｾｯﾄ間違い防止ﾜｯｼｬの確認",
"3. 下面に防錆油を塗布"
],
"WorkPoints": [
"ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄのｽﾄｯﾊﾟｰﾎﾞﾙﾄが左側の時ﾜｯｼｬｰに当たり挿入出来無い事",
"固定後､ が上下にｽﾑｰｽﾞな動作が出来ること... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4166",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付か無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "支柱・ｶﾊﾞｰ取付",
"WorkItems": [
"2. PLATE の裏面へ を取付ける",
"1. PLATE の裏面へCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.5N･m",
"WorkName": "支柱・ｶﾊﾞｰ取付",
"WorkItems": [
"2. PLATE の裏面へ を取付ける",
"1. PLATE の裏面へCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰとFT4の取付",
"WorkItems": [
"3. へCABLE-SUPPORT を圧入",
"1. BOLT WASHER を穴にｾｯﾄ後COVER をBOLT WASHER で締結",
"2. を治具台へ,1.で挿入したBOLT WASHER 4個と他のBOLT WASHER 8個で締結"
],
"WorkPoints": [
"治具取付方向注意ﾌﾟﾚｰﾄの逃げと治具の逃げ穴を合わせ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取りついている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｶﾊﾞｰとFT4の取付",
"WorkItems": [
"3. へCABLE-SUPPORT を圧入",
"1. BOLT WASHER を穴にｾｯﾄ後COVER をBOLT WASHER で締結",
"2. を治具台へ,1.で挿入したBOLT WASHER 4個と他のBOLT WASHER 8個で締結"
],
"WorkPoints": [
"治具取付方向注意ﾌﾟﾚｰﾄの逃げと治具の逃げ穴を合わせる... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ組立治具",
"Size": "",
"ToolOther": "FM-2777",
"WorkName": "ｶﾊﾞｰとFT4の取付",
"WorkItems": [
"3. へCABLE-SUPPORT を圧入",
"1. BOLT WASHER を穴にｾｯﾄ後COVER をBOLT WASHER で締結",
"2. を治具台へ,1.で挿入したBOLT WASHER 4個と他のBOLT WASHER 8個で締結"
],
"WorkPoints": [
"治具取付方向注意ﾌﾟﾚｰﾄの逃げと治具の逃げ穴を合... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2777",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取りついている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "5.3N･m",
"WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰの取付",
"WorkItems": [
"1. に を締結｡",
"1. をBOLT WASHER で仮付けする｡"
],
"WorkPoints": [
"ｼﾞｮｲﾝﾄの向き",
"ｼﾞｮｲﾝﾄの向き",
"ｼﾞｮｲﾝﾄの向き",
"ｼﾞｮｲﾝﾄの向き"
],
"Tolks": [],
"InspectionNo": "",
"Ins... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜(ﾛﾝｸﾞ)",
"ToolOther": "9.8N･m",
"WorkName": "ｽﾗｲﾄﾞﾌﾞｯｼｭの取付",
"WorkItems": [
"1. に をBOLT で取付ける｡"
],
"WorkPoints": [
"取付け穴の中央を狙って固定する事",
"A,Bのみ先付け､その他後付け"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾊﾞﾙﾌﾞ取付",
"WorkItems": [
"1. に をBOLT で､ をBOLT WASHER で取付ける｡"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第二実装ｽﾃｰｼ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾌﾞﾗｹｯﾄ類の取付",
"WorkItems": [],
"WorkPoints": [
"A矢視図",
"取付け位置注意",
"A矢視図",
"取付け位置注意",
"A矢視図",
"取付け位置注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 3... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "5045cN･m",
"WorkName": "ｼﾞｮｲﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ取付_1(交換ﾌﾟﾚｰﾄ上限ｾﾝｻｰ)",
"WorkItems": [
"1. に を固定する｡",
"2. に をBOLT WASHER で仮締め｡"
],
"WorkPoints": [
"最後方に寄せて取付ける｡",
"ｹｰﾌﾞﾙ･ｺﾈｸﾀｰの破損に注意",
"SD-0164023-058で本締結"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"In... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ取付_1(交換ﾌﾟﾚｰﾄ上限ｾﾝｻｰ)",
"WorkItems": [
"1. に を固定する｡",
"2. に をBOLT WASHER で仮締め｡"
],
"WorkPoints": [
"最後方に寄せて取付ける｡",
"ｹｰﾌﾞﾙ･ｺﾈｸﾀｰの破損に注意",
"SD-0164023-058で本締結"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ取付_2(交換ﾌﾟﾚｰﾄ有り無しｾﾝｻｰ)",
"WorkItems": [
"1. に FRAME をBOLT WASHER で仮付けする｡"
],
"WorkPoints": [
"最後方に寄せて取付ける｡",
"ｹｰﾌﾞﾙ･ｺﾈｸﾀｰの破損に注意",
"SD-0164023-059で本締結"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ取付_3(下受け上下ｾﾝｻｰ)",
"WorkItems": [
"1. にWASHER を当付けてBOLT WASHER で仮付けする｡"
],
"WorkPoints": [
"ｹｰﾌﾞﾙ･ｺﾈｸﾀｰの破損に注意",
"最後方に寄せて取付ける｡",
"SD-0164023-055で本締結"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝ配線の接続と結束(1)",
"WorkItems": [
"1. 各ﾌﾞﾗｹｯﾄにCABLE CABLE の配線を接続し結束する｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第二実装ｽﾃｰｼﾞ",
"第一実装ｽﾃｰｼﾞ",
"1... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝ配線の接続と結束(2)",
"WorkItems": [
"1. 各ﾊﾞﾙﾌﾞへの配線を接続",
"2. ㉖で固定"
],
"WorkPoints": [
"ｺﾈｸﾀｰ№を確認"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-008",
"InspectionItems": [
"検査表 :ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ配線の接続と結束(1)",
"WorkItems": [
"1. 各ﾌﾞﾗｯｹﾄへ配線を接続",
"2. ㉖で固定する"
],
"WorkPoints": [
"ﾌﾞﾗｯｹﾄ№とｺﾈｸﾀｰ№を確認",
"接続部ﾀﾞﾌﾞﾙﾁｪｯｸ(青･緑ﾏｰｷﾝｸﾞ)"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-008",
"InspectionItems": [
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ配線の結束(2)",
"WorkItems": [
"1. 各余分な配線をｲﾝｼｭﾛｯｸで結束"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸ締結箇所に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"L=150mm",
"L=150mm",... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管Ф4接続(1)",
"WorkItems": [
"1. Ф4の配管接続"
],
"WorkPoints": [
"点線部分はﾍﾞｰｽﾌﾟﾚｰﾄ下側へ引回す(接続時区別できる様に先端付近に黄ﾏｰｷﾝｸﾞする)",
"TUBEを接続する時は必ずJOINTを押さえる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管Ф4接続(2)",
"WorkItems": [
"1. Ф4の配管接続"
],
"WorkPoints": [
"点線部分はﾍﾞｰｽﾌﾟﾚｰﾄ下側へ引き回す",
"ｼﾞｮｲﾝﾄへの配管はﾗｼﾞﾍﾟﾝで確実に挿入する",
"TUBEを接続する時は必ずJOINTを押さえる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管Ф6接続(1)",
"WorkItems": [
"1. Ф6配線の接続"
],
"WorkPoints": [
"点線部分はﾍﾞｰｽﾌﾟﾚｰﾄ下側へ引き回す",
"ｼﾞｮｲﾝﾄへの配管はﾗｼﾞﾍﾟﾝで確実に挿入する",
"TUBEを接続する時は必ずJOINTを押さえる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管Ф6接続(2)",
"WorkItems": [
"1. Ф6配線の接続"
],
"WorkPoints": [
"点線部分はﾍﾞｰｽﾌﾟﾚｰﾄ下側へ引き回す",
"ｼﾞｮｲﾝﾄへの配管はﾗｼﾞﾍﾟﾝで確実に挿入する",
"TUBEを接続する時は必ずJOINTを押さえる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管Ф6接続(3)",
"WorkItems": [
"1. Ф6配線の接続"
],
"WorkPoints": [
"点線部分はﾍﾞｰｽﾌﾟﾚｰﾄ下側へ引き回す",
"ｼﾞｮｲﾝﾄへの配管はﾗｼﾞﾍﾟﾝで確実に挿入する",
"TUBEを接続する時は必ずJOINTを押さえる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線・配管の結束(1)",
"WorkItems": [
"1. 配線.ｴｱｰ配管をｲﾝｼｭﾛｯｸで結束"
],
"WorkPoints": [
"緑枠の内側へ配線.配管がはみ出さないこと(可動部)6箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第二実装ｽﾃｰｼﾞ",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線・配管の結束(2)",
"WorkItems": [
"1. 配線.ｴｱｰ配管をｲﾝｼｭﾛｯｸで結線"
],
"WorkPoints": [
"緑枠の内側へ配線.配管がはみ出さないこと(可動部)6箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"VVV",
"V... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管・配線参考写真(1)",
"WorkItems": [
"1. 配管･配線参考写真"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第一実装ｽﾃｰｼﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管・配線参考写真(2)",
"WorkItems": [
"1. 配管･配線参考写真"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第二実装ｽﾃｰｼﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜(ﾛﾝｸﾞ)",
"ToolOther": "9.8N･m",
"WorkName": "ｽﾗｲﾄﾞﾌﾞｯｼｭの取付",
"WorkItems": [
"1. に をBOLT で取付ける｡"
],
"WorkPoints": [
"取付け穴の中央を狙って固定する事",
"A,Bのみ先付け､その他の6個をここで取付"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "昇降ﾌﾟﾚｰﾄ位置決治具",
"Size": "",
"ToolOther": "FM-2798",
"WorkName": "下受け上下ﾌﾟﾚｰﾄ位置決め",
"WorkItems": [
"1. に を載せてPLATE BOLT で固定する｡",
"2. を治具に当てｼｬﾌﾄ固定ﾎﾞﾙﾄM6を締付ける"
],
"WorkPoints": [
"･左右で治具の取付け位置が 対象になる",
"ｼｬﾌﾄDｶｯﾄ面の方向に注意",
"PLATE のｽﾄｯﾊﾟｰ配置",
"PLATE の取付け方向に注意"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2798",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取りついているか",
"Method": "目視",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "下受け上下ﾌﾟﾚｰﾄ位置決め",
"WorkItems": [
"1. に を載せてPLATE BOLT で固定する｡",
"2. を治具に当てｼｬﾌﾄ固定ﾎﾞﾙﾄM6を締付ける"
],
"WorkPoints": [
"･左右で治具の取付け位置が 対象になる",
"ｼｬﾌﾄDｶｯﾄ面の方向に注意",
"PLATE のｽﾄｯﾊﾟｰ配置",
"PLATE の取付け方向に注意",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "下受け上下ﾌﾟﾚｰﾄ位置決め",
"WorkItems": [
"1. に を載せてPLATE BOLT で固定する｡",
"2. を治具に当てｼｬﾌﾄ固定ﾎﾞﾙﾄM6を締付ける"
],
"WorkPoints": [
"･左右で治具の取付け位置が 対象になる",
"ｼｬﾌﾄDｶｯﾄ面の方向に注意",
"PLATE のｽﾄｯﾊﾟｰ配置",
"PLATE の取付け方向に注意",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "交換ｼﾘﾝﾀﾞｰのФ4配管接続",
"WorkItems": [
"1. ｼﾘﾝﾀﾞｰにФ4のｴｱｰﾎｰｽを接続",
"2. ｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints": [
"ｼﾞｮｲﾝﾄへの配管挿入はﾗｼﾞﾍﾟﾝで確実に接続する",
"黄色ﾏｰｷﾝｸﾞがされている配管をｼﾘﾝﾀﾞｰ下側へ接続する",
"第二ﾌﾟﾚｰﾄ上昇時Ф4配管がﾍﾞｰｽﾌﾟﾚｰﾄｴｯｼﾞに干渉して無い事",
"配管がﾍﾞｰ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄの高さ調整とﾒｲﾝｼﾘﾝﾀﾞｰの連結",
"WorkItems": [
"1. ﾒｲﾝｼﾘﾝﾀﾞｰのﾛｯﾄﾞの芯出し",
"◆2. CYL-NUT WASHER の取付と高さ調整し､CYL-NUT を締結する"
],
"WorkPoints": [
"･最上死点及び最下死点位置でのﾛｯｸ禁止 (ｼﾘﾝﾀﾞｰｽﾄﾛｰｸの中立位置でﾛｯｸする事)･締付ける際ｾﾝｻｰ等の破損に注意",
"4.5±0.05mm"
],
... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒8",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "上ﾌﾟﾚｰﾄの高さ調整とﾒｲﾝｼﾘﾝﾀﾞｰの連結",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾎﾞﾙﾄを緩め上部ﾌﾟﾚｰﾄに治具を挿入しｼﾘﾝﾀﾞｰｼｬﾌﾄの芯出し行い... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄの高さ調整とﾒｲﾝｼﾘﾝﾀﾞｰの連結",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾎﾞﾙﾄを緩め上部ﾌﾟﾚｰﾄに治具を挿入しｼﾘﾝﾀﾞｰｼｬﾌﾄの芯出し行い... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:4.5±0.05㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰ位置調整治具",
"Size": "",
"ToolOther": "FM-2982",
"WorkName": "上ﾌﾟﾚｰﾄの高さ調整とﾒｲﾝｼﾘﾝﾀﾞｰの連結",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾎﾞﾙﾄを緩め上部ﾌﾟﾚｰﾄに治具を挿入しｼﾘﾝﾀﾞｰｼｬﾌﾄの... | {
"QualityItem": "芯出確認",
"ToolManageNo": "FM-2982",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り芯出しされていること",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "交換ﾌﾟﾚｰﾄ上下の取付け",
"WorkItems": [
"1. に を載せて下から を通してSPACER WASHER を入れ､BOLT WASHER で仮固定する"
],
"WorkPoints": [
"SD-0164023-053で本締結",
"ｼｬﾌﾄを先に入れる､ｶﾗｰが落下する為",
"ｼｬﾌﾄのHｶｯﾄ部の方向を同一方向へ向けておくこと"
],
"Tolks": [],
"Inspection... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受平面度測定ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-4166",
"WorkName": "交換ﾌﾟﾚｰﾄ位置出し調整",
"WorkItems": [
"3. 治具をA.Bどちらか当たるまで近づけﾄﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ及びﾍﾞｰｽﾌﾟﾚｰﾄA.Bの隙間測定",
"6. 交換ﾌﾟﾚｰﾄ上昇ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと治具を抜き前方ｼｬﾌﾄ固定ﾎﾞﾙﾄを締結",
"5. 後方のｼｬﾌﾄ固定ﾎﾞﾙﾄ締結",
"4. 交換ﾌﾟﾚｰﾄ全体を動かし調整",
"2. にﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと治具(F... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4166",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "昇降ﾌﾟﾚｰﾄ位置決治具",
"Size": "",
"ToolOther": "FM-2798",
"WorkName": "交換ﾌﾟﾚｰﾄ位置出し調整",
"WorkItems": [
"3. 治具をA.Bどちらか当たるまで近づけﾄﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ及びﾍﾞｰｽﾌﾟﾚｰﾄA.Bの隙間測定",
"6. 交換ﾌﾟﾚｰﾄ上昇ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと治具を抜き前方ｼｬﾌﾄ固定ﾎﾞﾙﾄを締結",
"5. 後方のｼｬﾌﾄ固定ﾎﾞﾙﾄ締結",
"4. 交換ﾌﾟﾚｰﾄ全体を動かし調整",
"2. にﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと治具(F... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2798",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "交換ﾌﾟﾚｰﾄ位置出し調整",
"WorkItems": [
"3. 治具をA.Bどちらか当たるまで近づけﾄﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ及びﾍﾞｰｽﾌﾟﾚｰﾄA.Bの隙間測定",
"6. 交換ﾌﾟﾚｰﾄ上昇ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと治具を抜き前方ｼｬﾌﾄ固定ﾎﾞﾙﾄを締結",
"5. 後方のｼｬﾌﾄ固定ﾎﾞﾙﾄ締結",
"4. 交換ﾌﾟﾚｰﾄ全体を動かし調整",
"2. にﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと治具(FM-416... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "9±0.1㎜隙間:0.1㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "交換ﾌﾟﾚｰﾄ上下の高さ調整とｼﾘﾝﾀﾞｰの連結",
"WorkItems": [
"◆1. ﾒｲﾝｼﾘﾝﾀﾞｰのﾛｯﾄﾞにCYL-NUT を取付｡",
"2. CYL-NUT の位置調整･固定"
],
"WorkPoints": [
"2.5mm±0.05mm",
"･最上死点及び最下死点位置でのﾛｯｸ禁止 (ｼﾘﾝﾀﾞｰｽﾄﾛｰｸの中立位置でﾛｯｸする事)･締付ける際ｾﾝｻｰ等の破損に注意",
"CYL-NUT の指示... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "交換ﾌﾟﾚｰﾄ上下の高さ調整とｼﾘﾝﾀﾞｰの連結",
"WorkItems": [
"◆1. ﾒｲﾝｼﾘﾝﾀﾞｰのﾛｯﾄﾞにCYL-NUT を取付｡",
"2. CYL-NUT の位置調整･固定"
],
"WorkPoints": [
"CYL-NUT の指示部にｸﾞﾘｰｽｱｯﾌﾟを行う事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "2.5±0.05㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞｸﾞの取付け調整_1",
"WorkItems": [
"1. にDOG をBOLT WASHER で固定"
],
"WorkPoints": [
"A(奥行き)調整用",
"B(左右位置)調整用",
"㉘に繋ぎ2～3回上下動させ、上限状態で保持し調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾄﾞｸﾞの取付け調整_1",
"WorkItems": [
"1. にDOG をBOLT WASHER で固定"
],
"WorkPoints": [
"A(奥行き)調整用",
"B(左右位置)調整用",
"㉘に繋ぎ2～3回上下動させ、上限状態で保持し調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "突き上げﾌﾟﾚｰﾄの位置決め",
"WorkItems": [
"1. にPLATE をBOLT で取付け(仮止め)",
"2. PLATE の出代寸法と平面度を確認し締結"
],
"WorkPoints": [
"ﾎﾙﾀﾞｰを上下させ､下降した状態で測定",
" 基準高さ110.5mm±0.05mm",
"A･B寸法36.0mm+±0.1mm",
"作業2で本締結",
... | {
"QualityItem": "平面度",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "突き上げﾌﾟﾚｰﾄの位置決め",
"WorkItems": [
"1. にPLATE をBOLT で取付け(仮止め)",
"2. PLATE の出代寸法と平面度を確認し締結"
],
"WorkPoints": [
"ﾎﾙﾀﾞｰを上下させ､下降した状態で測定",
" 基準高さ110.5mm±0.05mm",
"A･B寸法36.0mm+±0.1mm",
"作業2で本締結",
" ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "110.5㎜",
"ToolOther": "",
"WorkName": "突き上げﾌﾟﾚｰﾄの位置決め",
"WorkItems": [
"1. にPLATE をBOLT で取付け(仮止め)",
"2. PLATE の出代寸法と平面度を確認し締結"
],
"WorkPoints": [
"ﾎﾙﾀﾞｰを上下させ､下降した状態で測定",
" 基準高さ110.5mm±0.05mm",
"A･B寸法36.0mm+±0.1mm",
"作業2で本締結",
... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "110.5±0.05㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "突き上げﾌﾟﾚｰﾄの位置決め",
"WorkItems": [
"1. にPLATE をBOLT で取付け(仮止め)",
"2. PLATE の出代寸法と平面度を確認し締結"
],
"WorkPoints": [
"ﾎﾙﾀﾞｰを上下させ､下降した状態で測定",
" 基準高さ110.5mm±0.05mm",
"A･B寸法36.0mm+±0.1mm",
"作業2で本締結",
" ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "36.0±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ平面度測定",
"WorkItems": [
"1. FM-2777組立台にFM-3167ﾌﾟﾚｰﾄ調整用治具をｾｯﾄする",
"2. 基準点のﾌﾞﾛｯｸｹﾞｰｼﾞを0点とし指示されて測定ﾎﾟｲﾝﾄを規格値に調整のこと",
"3. 再度P005のPLATEの精度を確認する(前ﾍﾟｰｼﾞ)"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄを上昇させﾌﾟﾚｰﾄ上面をﾋﾟｯ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾌｫﾙﾀﾞ組立台",
"Size": "",
"ToolOther": "FM-2777",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ平面度測定",
"WorkItems": [
"1. FM-2777組立台にFM-3167ﾌﾟﾚｰﾄ調整用治具をｾｯﾄする",
"2. 基準点のﾌﾞﾛｯｸｹﾞｰｼﾞを0点とし指示されて測定ﾎﾟｲﾝﾄを規格値に調整のこと",
"3. 再度P005のPLATEの精度を確認する(前ﾍﾟｰｼﾞ)"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄを上昇させﾌﾟﾚｰﾄ上面をﾋﾟｯｸﾃｽﾄ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2777",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3.45㎜",
"ToolOther": "",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ平面度測定",
"WorkItems": [
"3. 再度P005のPLATEの精度を確認する(前ﾍﾟｰｼﾞ)"
],
"WorkPoints": [
" 3.45±0.05mm",
" ~⑭平面度0.1mm以内",
"最終上下動作させ両方を再確認する",
"調整後㉝の治具と治具を押えるｶﾗｰとのｽｷﾏが無いこと"
],
"Tolks": [
"締付ﾄ... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3.45㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ平面度測定",
"WorkItems": [
"3. 再度P005のPLATEの精度を確認する(前ﾍﾟｰｼﾞ)"
],
"WorkPoints": [
" 3.45±0.05mm",
" ~⑭平面度0.1mm以内",
"最終上下動作させ両方を再確認する",
"調整後㉝の治具と治具を押えるｶﾗｰとのｽｷﾏが無いこと"
],
"Tolks": [
"... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受平面度測定ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-4166",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ平面度測定",
"WorkItems": [
"1. FM-2777組立台にFM-3167ﾌﾟﾚｰﾄ調整用治具をｾｯﾄする",
"3. 再度P005のPLATEの精度を確認する(前ﾍﾟｰｼﾞ)",
"2. 基準点のﾌﾞﾛｯｸｹﾞｰｼﾞを0点とし指示されて測定ﾎﾟｲﾝﾄを規格値に調整のこと"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄを上昇させﾌﾟﾚｰﾄ上面をﾋﾟｯｸﾃ... | {
"QualityItem": "平面度確認",
"ToolManageNo": "FM-4166",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜以内",
"Method": "下受平面度測定ﾌﾟﾚｰﾄ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ平面度測定",
"WorkItems": [
"3. 再度P005のPLATEの精度を確認する(前ﾍﾟｰｼﾞ)"
],
"WorkPoints": [
" 3.45±0.05mm",
" ~⑭平面度0.1mm以内",
"最終上下動作させ両方を再確認する",
"調整後㉝の治具と治具を押えるｶﾗｰとのｽｷﾏが無いこと"
],
"Tolks": [
"締付ﾄﾙ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄ平面度測定",
"WorkItems": [
"1. FM-2777組立台にFM-3167ﾌﾟﾚｰﾄ調整用治具をｾｯﾄする",
"3. 再度P005のPLATEの精度を確認する(前ﾍﾟｰｼﾞ)",
"2. 基準点のﾌﾞﾛｯｸｹﾞｰｼﾞを0点とし指示されて測定ﾎﾟｲﾝﾄを規格値に調整のこと"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄを上昇させﾌﾟﾚｰﾄ上面をﾋﾟｯｸﾃｽﾄで確認(ずれが大きい場... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞｸﾞの取付け調整_2",
"WorkItems": [
"2. ﾄﾞｸﾞ位置ｾﾝｻｰ位置を調整"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞにて上下動作を行い調整確認する"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞｸﾞの取付け調整_2",
"WorkItems": [
"2. ﾄﾞｸﾞ位置ｾﾝｻｰ位置を調整"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞにて上下動作を行い調整確認する"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受平面度測定ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-4166",
"WorkName": "ﾄﾞｸﾞの取付け調整_3",
"WorkItems": [
"1. へ をBOLT WASHER で締結",
"3. ﾄﾞｸﾞ位置に対しｾﾝｻｰを調整",
"2. 調整後ﾌﾟﾚｰﾄ(P618)を締結"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞにて上下動作を途中で止め(ﾄﾞｸﾞ上部と中部と下部3箇所)調整確認する",
"ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと の隙間を0.4~0.5㎜に調整し... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-4166",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜以内",
"Method": "下受平面度測定ﾌﾟﾚｰﾄ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.5㎜",
"ToolOther": "",
"WorkName": "ﾄﾞｸﾞの取付け調整_3",
"WorkItems": [
"1. へ をBOLT WASHER で締結",
"2. 調整後ﾌﾟﾚｰﾄ(P618)を締結"
],
"WorkPoints": [
"ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと の隙間を0.4~0.5㎜に調整し､後ｽﾄｯﾊﾟｰとの隙間を0.1㎜に調整する｡"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 1.5N... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.4~0.5㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜(ﾛﾝｸﾞ)",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞｸﾞの取付け調整_3",
"WorkItems": [
"1. へ をBOLT WASHER で締結",
"2. 調整後ﾌﾟﾚｰﾄ(P618)を締結"
],
"WorkPoints": [
"ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと の隙間を0.4~0.5㎜に調整し､後ｽﾄｯﾊﾟｰとの隙間を0.1㎜に調整する｡"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.5㎜",
"ToolOther": "",
"WorkName": "ﾄﾞｸﾞの取付け調整_3",
"WorkItems": [
"1. へ をBOLT WASHER で締結",
"2. 調整後ﾌﾟﾚｰﾄ(P618)を締結"
],
"WorkPoints": [
"ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと の隙間を0.4~0.5㎜に調整し､後ｽﾄｯﾊﾟｰとの隙間を0.1㎜に調整する｡"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 1.5N... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.1㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜(ﾛﾝｸﾞ)",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞｸﾞの取付け調整_3",
"WorkItems": [
"1. へ をBOLT WASHER で締結",
"2. 調整後ﾌﾟﾚｰﾄ(P618)を締結"
],
"WorkPoints": [
"ﾏﾄﾘｯｸｽﾌﾟﾚｰﾄと の隙間を0.4~0.5㎜に調整し､後ｽﾄｯﾊﾟｰとの隙間を0.1㎜に調整する｡"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾕﾆｯﾄﾁｪｯｶｰ操作説明(手動動作下受け上下)",
"WorkItems": [
"1. 各ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞのｽﾋﾟｺﾝの開き具合を確認のこと",
"2. 手動操作説明"
],
"WorkPoints": [
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF*操作時は二人作業禁止*",
"全閉から3.5回転開(ﾛｯｸ)",
"全開(仮ﾛｯｸ)",
"全閉から4回転開(仮... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾕﾆｯﾄﾁｪｯｶｰ操作説明(速度調整)",
"WorkItems": [
"1. 速度調整操作説明"
],
"WorkPoints": [
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF*操作時は二人作業禁止*"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾕﾆｯﾄﾁｪｯｶｰ操作説明(ｴｰｼﾞﾝｸﾞ)",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞ操作説明"
],
"WorkPoints": [
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF*操作時は二人作業禁止*"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"W... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.0N･m",
"WorkName": "下受け上下のｽﾋﾟｰﾄﾞ調整(速度切替無し)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
" 下降側ﾛｯｸﾅｯﾄ(黒)",
" 下降側ﾛｯｸﾅｯﾄ(黒)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.5N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受け上下のｽﾋﾟｰﾄﾞ調整(速度切替無し)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WDQB-F013-008",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
" 下降側ﾛｯｸﾅｯﾄ(黒)",
" 下降側ﾛｯｸﾅｯﾄ(黒)",
"W... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "下降:1.25~1.35s上昇:1.55~1.65s",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.0N･m",
"WorkName": "下受け上下のｽﾋﾟｰﾄﾞ調整(速度切替有り)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
" 下降側ﾛｯｸﾅｯﾄ(黒)",
" 下降側ﾛｯｸﾅｯﾄ(黒)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.0N･m",
"WorkName": "下受け上下のｽﾋﾟｰﾄﾞ調整(速度切替有り)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
" 下降側ﾛｯｸﾅｯﾄ(黒)",
" 下降側ﾛｯｸﾅｯﾄ(黒)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.5N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受け上下のｽﾋﾟｰﾄﾞ調整(速度切替有り)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WDQB-F013-008",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
" 下降側ﾛｯｸﾅｯﾄ(黒)",
" 下降側ﾛｯｸﾅｯﾄ(黒)",
" ... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "下降:1.25s~1.35s上昇:1.55s~1.65s",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受け上下のｽﾋﾟｰﾄﾞ調整(速度切替有り)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WDQB-F013-008",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
" 下降側ﾛｯｸﾅｯﾄ(黒)",
" 下降側ﾛｯｸﾅｯﾄ(黒)",
" ... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "下降:1.00s~1.15s上昇:0.47s~0.62s",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-008",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付け_2",
"WorkItems": [
"1. へ②を貼付け"
],
"WorkPoints": [
"貼付け部分を脱脂する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"第一実装ｽﾃｰｼﾞ",
"第二実装ｽﾃｰｼﾞ",
"第一実装ｽﾃｰｼﾞ(若... | {
"QualityItem": "貼付位置",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り張付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "防錆油塗布",
"WorkItems": [
"1. ･ に防錆油を塗布する｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾙ部全面防錆油塗布",
"下受け交換部全面防錆油塗布",
"可動ｽﾄｯﾊﾟｰとその周辺は防錆油を塗布し無い... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ対応)(第一実装)底面ｶﾊﾞ-取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"COVER BOLT WASHER ",
"狭い",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ吊上げ用治具",
"Size": "",
"ToolOther": "FM-2793",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ対応)(第一実装)底面ｶﾊﾞ-取付",
"WorkItems": [
"◆1. 基板ﾎﾙﾀﾞ(第一実装)をﾘﾌﾀｰで吊り上げる｡",
"◆2. 基板ﾎﾙﾀﾞにCOVER ･COVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"･F側にCOVER を､R側にCOVER を取付"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2793",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られていること",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ対応)(第二実装)底面ｶﾊﾞ-取付",
"WorkItems": [
"◆1. 基板ﾎﾙﾀﾞ(第二実装)をﾘﾌﾀｰで吊り上げる",
"◆2. 基板ﾎﾙﾀﾞにCOVER ･COVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ吊上げ用治具",
"Size": "",
"ToolOther": "FM-2793",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ対応)(第二実装)底面ｶﾊﾞ-取付",
"WorkItems": [
"◆1. 基板ﾎﾙﾀﾞ(第二実装)をﾘﾌﾀｰで吊り上げる",
"◆2. 基板ﾎﾙﾀﾞにCOVER ･COVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2793",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｽﾄｯﾊﾟｰ_1前準備(自動ﾋﾟﾝ交換仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ_2前準備(自動ﾋﾟﾝ交換仕様)",
"WorkItems": [
"1. POST にSCREW を組み付ける",
"2. 作業1の完成品と を組立てる"
],
"WorkPoints": [
"POST をｽﾊﾟﾅで固定しSCREW が止まる位置まで締付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ_2取付(自動ﾋﾟﾝ交換仕様)",
"WorkItems": [
"1. へ WASHER を取付ける",
"2. ﾘｱ側に を取付ける"
],
"WorkPoints": [
"･第一･第二実装ｽﾃｰｼﾞとも取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付け_3",
"WorkItems": [
"1. COVER へ②を貼付け"
],
"WorkPoints": [
"第二実装R側に取付け",
"第一実装F側に取付け",
"貼付け部分を脱脂する",
"④枚中2枚に貼付ける",
"貼付け後4枚をｾｯﾄとしてｽﾙｰ部品として添付すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "貼付位置",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り張付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品の準備",
"WorkItems": [
"1. 以下の付属品準備及びﾁｪｯｸ",
"2. 4. Ф6 ﾁｭｰﾌﾞを二本を1120mmにｶｯﾄ",
"3. 上記表示の部品を揃えてｽﾙｰ部品としてﾕﾆｯﾄに添付すること"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "組立前の注意事項と各ｽﾃｰｼｮﾝの名称",
"WorkItems": [
"1. 各ｽﾃｰｼｮﾝ名称及び説明",
"2. 締結後の増締めﾁｪｯｸ(ﾀﾞﾌﾞﾙﾁｪｯｸ)について",
"3. 組立前の油砥石がけについて｡"
],
"WorkPoints": [
"本体搭載時の配置図",
"･標準書は左記名称で表記されているので 組立時､どのﾚｰﾝになるか理解しておく事",
"･本ﾕﾆｯﾄは本体1台に対し4ﾕﾆｯﾄ (... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ組立①",
"WorkItems": [
"1. VALVE にJOINT JOINT SPEED-CONTROLLER を取付ける",
"2. BRACKET に上記完成品をWASHER BOLT で取付ける"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞを全閉から1回転開ける｡(微調整は後工程の上下ｽﾋﾟｰﾄﾞ調整で実施)"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
... | {
"QualityItem": "ｽﾋﾟｺﾝ回転量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全閉から1回転開ける",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN.m",
"WorkName": "ﾊﾞﾙﾌﾞ組立①",
"WorkItems": [
"2. BRACKET に上記完成品をWASHER BOLT で取付ける"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞを全閉から1回転開ける｡(微調整は後工程の上下ｽﾋﾟｰﾄﾞ調整で実施)"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ組立②",
"WorkItems": [
"1. VALVE にSPEED-CONTROLLER SILENCER JOINT を取付ける",
"2. SPEED-CONTROLLER のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整し､ﾛｯｸする",
"3. 上記完成品をBRACKET にWASHER WASHER BOLT 取付ける"
],
"WorkPoints": [
"上昇側:全開",
"ﾊﾞﾙﾌﾞが傾かないこと",
... | {
"QualityItem": "回転量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "上昇側:全開下降側:全閉から3回転開ける",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "5045cN･m",
"WorkName": "ﾊﾞﾙﾌﾞ組立②",
"WorkItems": [],
"WorkPoints": [
"ﾊﾞﾙﾌﾞが傾かないこと",
"下降側:全閉から2.5回転"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "六角ﾎﾟｽﾄ組立①",
"WorkItems": [
"1. SPACER にSCREW をねじ込む｡"
],
"WorkPoints": [
"SPACER の両端に砥石をかけてからSCREW をねじ込む事",
"ﾏｰｶ-はﾈｼﾞの内側(ﾈｼﾞ部にかから無い事)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": []... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "六角ﾎﾟｽﾄ組立②",
"WorkItems": [
"1. SPACER にSCREW をねじ込む｡"
],
"WorkPoints": [
"ﾏｰｶ-はﾈｼﾞの内側(ﾈｼﾞ部にかから無い事)",
"SPACER の底までSCREW を挿入し締付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｾﾝｻｰ部組立",
"WorkItems": [
"1. PLATE にSENSOR (2ヶ)SPACER をBOLT WASHER WASHER で取付ける",
"2. LABEL を取付ける"
],
"WorkPoints": [
"PLATE の取付け方向に注意",
"広い",
"狭い",
"SENSOR の方向に注意",
"表示がある方を上にする",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ部組立",
"WorkItems": [
"2. LABEL を取付ける"
],
"WorkPoints": [
"30mm",
"LABEL 取付け位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"親配線No.",
"上下ｾﾝｻｰN... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "30㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.