input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "部品搭載ﾊﾟﾚｯﾄ平面度測定",
"WorkItems": [
"2. ㉖に を設置する",
"1. ㉖の平面度を測定する。"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"138㎜",
"138㎜",
"2LC-JG-23004"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.2㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "2LC-JG-23004",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "5.3N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. に をBOLT で取付ける",
"1. に をBOLT で取付ける"
],
"WorkPoints": [
" のﾋﾟﾝが に押し当てられている事(2箇所)",
" のﾋﾟﾝが に押し当てられている事(2箇所)",
" のﾋﾟﾝが に押し当てられている事(2箇所)",
" のﾋﾟﾝが に押し当てられている事(2箇所)"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "背面ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"配線を挟み込まないように注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴﾝｺｰﾀﾞｰ配線の接続",
"WorkItems": [
"1. のｴﾝｺｰﾀﾞｰ配線を引き回し､ｺﾈｸﾀに接続する"
],
"WorkPoints": [
"CN5K302",
"CN3K302",
"CN4K302",
"照明の配線は後工程で引き回すのでまとめておく"
],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :接続ﾁｪｯｸ_ｴﾝｺｰﾀﾞ中継基板",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "ｴﾝｺｰﾀﾞｰ配線の接続",
"WorkItems": [
"1. のｴﾝｺｰﾀﾞｰ配線を引き回し､ｺﾈｸﾀに接続する"
],
"WorkPoints": [
"CN5K302",
"CN3K302",
"CN4K302",
"照明の配線は後工程で引き回すのでまとめておく"
],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :接続ﾁｪｯｸ_ｴﾝｺｰﾀﾞ中継基板"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "上面ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. に をBOLT とBOLT WASHER で取付ける"
],
"WorkPoints": [
" のﾋﾟﾝに を載せて取付ける事",
" の裏面よりBOLT WASHER を取付ける事",
" のﾋﾟﾝが に当付けられている事"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "CPU-BOX取付",
"WorkItems": [
"2. に をBOLT WASHER ､WASHER BOLT で取付ける",
"■1. の型式を確認し､ｼﾘｱﾙNoを検査表記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "CPU-BOX取付",
"WorkItems": [
"2. に をBOLT WASHER ､WASHER BOLT で取付ける",
"■1. の型式を確認し､ｼﾘｱﾙNoを検査表記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOX取付",
"WorkItems": [
"2. に をBOLT WASHER ､WASHER BOLT で取付ける",
"■1. の型式を確認し､ｼﾘｱﾙNoを検査表記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ",
"2LC-JG-23015"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認検査書有無確認",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ACｲﾝﾚｯﾄ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ACｲﾝﾚｯﾄ取付",
"WorkItems": [
"2. にSOFTWARE-LICENSE SOFTWARE-LICENSE を貼付ける"
],
"WorkPoints": [
"AC配線は後工程で引き回すので丸めておく事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾗｲｾﾝｽﾗﾍﾞﾙ貼付け確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOXAC配線引き回し1",
"WorkItems": [
"2. ACｲﾝﾚｯﾄの配線と一緒に上面ﾌﾟﾚｰﾄ側に引き回し､ｲﾝｼｭﾛｯｸで結束する",
"■1. にCABLE を接続する"
],
"WorkPoints": [
"1aF101と3aF101はﾌﾞﾚｰｶｰへ",
"4X02はｱｰｽﾌﾟﾚｰﾄへ",
"接続後､抜け防止でﾛｯｸする",
"AC(N)bT101とAC(L)bT101は24V電源へ",
"被覆の端面で結束する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :CPU BOX確認",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "250cN･m",
"WorkName": "CPU-BOXAC配線引き回し2",
"WorkItems": [
"2. 付属のｶﾊﾞｰを取付ける",
"■1. のﾌﾞﾚｰｶｰに配線を接続する"
],
"WorkPoints": [
"接続間違いに注意",
"ｶﾁｯと音がするまで差込む事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "50cN･m",
"WorkName": "CPU-BOXAC配線引き回し2",
"WorkItems": [
"3. にCOVER をSCREW で取付ける"
],
"WorkPoints": [
"1aF101",
"3aF101"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "CPU-BOXAC配線引き回し3",
"WorkItems": [
"■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する",
"■1. の24V電源に配線を接続する"
],
"WorkPoints": [
"背合せで取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "180cN･m",
"WorkName": "CPU-BOXAC配線引き回し3",
"WorkItems": [
"■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する",
"■1. の24V電源に配線を接続する"
],
"WorkPoints": [
"背合せで取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOXAC配線引き回し3",
"WorkItems": [
"■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する",
"■1. の24V電源に配線を接続する"
],
"WorkPoints": [
"AC(N)aT101AC(N)bT101",
"4X02",
"AC(L)aT101AC(L)bT101",
"背合せで取付ける事",
"1X02"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "DC配線引き回し",
"WorkItems": [
"2. 配線を引き回しｺﾈｸﾀへ接続する",
"■1. の24V電源にCABLE の配線を接続する"
],
"WorkPoints": [
"+V2aT101",
"-V2aT101-V2bT101",
"ｶﾁｯと音がするまで差込む事",
"背合せで取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表 :ｴﾝｺｰﾀﾞ中継基板",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC配線引き回し",
"WorkItems": [
"2. 配線を引き回しｺﾈｸﾀへ接続する",
"■1. の24V電源にCABLE の配線を接続する"
],
"WorkPoints": [
"+V2aT101",
"-V2aT101-V2bT101",
"ｶﾁｯと音がするまで差込む事",
"背合せで取付ける事",
"ここの穴から下に通す"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表 :ｴﾝｺｰﾀﾞ中継基板",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "MC-S取付①",
"WorkItems": [
"■1. の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"◆2. に をBOLT WASHER NUT で仮止めする"
],
"WorkPoints": [
" の開口部に⑥の配線を挟み込まない様に注意する事",
" の開口部やXYZﾃｰﾌﾞﾙに を干渉させない様に注意して取付ける事",
"左右4箇所仮締めする事",
"本締工程:SD-A046607-515",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ",
"2LC-JG-23015"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "MC-S取付①",
"WorkItems": [
"■1. の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"◆2. に をBOLT WASHER NUT で仮止めする"
],
"WorkPoints": [
" の開口部に⑥の配線を挟み込まない様に注意する事",
" の開口部やXYZﾃｰﾌﾞﾙに を干渉させない様に注意して取付ける事",
"左右4箇所仮締めする事",
"本締工程:SD-A046607-515",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "MC-S取付②",
"WorkItems": [
"2. 1完成品にCOVER を貼付ける",
"3. MC-Sからの配線を引き回し固定する",
"1. のMC-Sのﾌﾟﾚｰﾄと上面ﾌﾟﾚｰﾄの隙間を11㎜に調整し､仮締めﾎﾞﾙﾄを締結する"
],
"WorkPoints": [
"COVER の貼付け位置を脱脂し､右端から5㎜の位置に貼付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"11㎜",
"11㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "11㎜",
"ToolOther": "",
"WorkName": "MC-S取付②",
"WorkItems": [
"2. 1完成品にCOVER を貼付ける",
"3. MC-Sからの配線を引き回し固定する",
"1. のMC-Sのﾌﾟﾚｰﾄと上面ﾌﾟﾚｰﾄの隙間を11㎜に調整し､仮締めﾎﾞﾙﾄを締結する"
],
"WorkPoints": [
"COVER の貼付け位置を脱脂し､右端から5㎜の位置に貼付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"11㎜",
"11㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "MC-S取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5㎜",
"ｺﾈｸﾀｰはﾌﾞﾗｹｯﾄに挿入する"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LANｹｰﾌﾞﾙ引き回し",
"WorkItems": [
"3. にCABLE を引き回す",
"■1. CABLE のRoHSﾏｰｸを確認する",
"2. CABLE にNOISE-FILTER を取付ける"
],
"WorkPoints": [
"LAN1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"60㎜",
"検査表 :CPU BOX確認",
"検査表 :ﾌｪﾗｲﾄｺｱ",
"検査表 :CPU BOX確認",
"2LC-JG-23015"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "RoHSﾏｰｸが貼付け出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "LANｹｰﾌﾞﾙ引き回し",
"WorkItems": [
"3. にCABLE を引き回す",
"■1. CABLE のRoHSﾏｰｸを確認する",
"2. CABLE にNOISE-FILTER を取付ける"
],
"WorkPoints": [
"LAN1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"60㎜",
"検査表 :CPU BOX確認",
"検査表 :ﾌｪﾗｲﾄｺｱ",
"検査表 :CPU BOX確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LANｹｰﾌﾞﾙ引き回し",
"WorkItems": [
"3. にCABLE を引き回す",
"■1. CABLE のRoHSﾏｰｸを確認する",
"2. CABLE にNOISE-FILTER を取付ける"
],
"WorkPoints": [
"LAN1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"60㎜",
"検査表 :CPU BOX確認",
"検査表 :ﾌｪﾗｲﾄｺｱ",
"検査表 :CPU BOX確認",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "照明配線引き回し",
"WorkItems": [
"1. に照明配線を下から上面ﾌﾟﾚｰﾄまで引き回し､接続する"
],
"WorkPoints": [
"1CN0E001R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "150cN･m",
"WorkName": "CP~MC-Sﾕﾆｯﾄ引き回し",
"WorkItems": [
"2. CABLE を引き回し､MC-Sへ接続する",
"■1. のCPにCABLE を接続する"
],
"WorkPoints": [
"4aF102",
"2aF102",
"CN1K307"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表 :接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CP~MC-Sﾕﾆｯﾄ引き回し",
"WorkItems": [
"2. CABLE を引き回し､MC-Sへ接続する",
"■1. のCPにCABLE を接続する"
],
"WorkPoints": [
"4aF102",
"2aF102",
"CN1K307"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表 :接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "FG配線引き回し",
"WorkItems": [
"■1. にCABLE をSCREW で固定する"
],
"WorkPoints": [
"FGF1",
"FGK",
"横から見た図"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FG配線引き回し",
"WorkItems": [
"■1. にCABLE をSCREW で固定する"
],
"WorkPoints": [
"FGF1",
"FGK",
"横から見た図"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴﾝｺｰﾀﾞ配線引き回し",
"WorkItems": [
"1. にCABLE を引き回し､接続する"
],
"WorkPoints": [
"CN2K302",
"CN2K307",
"ｶﾁｯと音がするまで差込む事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"検査表 :ｴﾝｺｰﾀﾞ中継基板",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｪﾗｲﾄｺｱ取付",
"WorkItems": [
"■1. NOISE-FILTER ､FILTER の型式を確認する",
"2. にNOISE-FILTER FILTER を取付ける",
"3. ﾌｪﾗｲﾄｺｱがずれない様にｲﾝｼｭﾛｯｸで固定する(3箇所)",
"4. LED照明配線のﾌｪﾗｲﾄｺｱとLANｹｰﾌﾞﾙのﾌｪﾗｲﾄｺｱをｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯと音がするまで差込む事",
"型式",
"LED照明配線",
"型式",
"抜き窓から100mmの位置",
"ｲﾝｼｭﾛｯｸから50mmの位置",
"ｲﾝｼｭﾛｯｸから10mmの位置",
"ｴﾝｺｰﾀﾞ配線",
"AC配線"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :型式･検査書ﾁｪｯｸ",
"検査表 :ﾌｪﾗｲﾄｺｱの確認",
"100㎜",
"50㎜",
"10㎜",
"2LC-JG-23015"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｪﾗｲﾄｺｱ取付",
"WorkItems": [
"■1. NOISE-FILTER ､FILTER の型式を確認する",
"2. にNOISE-FILTER FILTER を取付ける",
"3. ﾌｪﾗｲﾄｺｱがずれない様にｲﾝｼｭﾛｯｸで固定する(3箇所)",
"4. LED照明配線のﾌｪﾗｲﾄｺｱとLANｹｰﾌﾞﾙのﾌｪﾗｲﾄｺｱをｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯと音がするまで差込む事",
"型式",
"LED照明配線",
"型式",
"抜き窓から100mmの位置",
"ｲﾝｼｭﾛｯｸから50mmの位置",
"ｲﾝｼｭﾛｯｸから10mmの位置",
"ｴﾝｺｰﾀﾞ配線",
"AC配線"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ",
"検査表 :ﾌｪﾗｲﾄｺｱの確認",
"100㎜",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-ﾋﾞｯﾄ3㎜",
"ToolOther": "15cN･m",
"WorkName": "ｶﾒﾗ配線引き回し",
"WorkItems": [
"1. にCABLE を引き回し､接続する",
"2. CABLE にLABEL を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"検査表 :CPU BOX確認",
"LABEL の端面を当てて固定する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ配線引き回し",
"WorkItems": [
"1. にCABLE を引き回し､接続する",
"2. CABLE にLABEL を取付ける"
],
"WorkPoints": [
"CN2K307",
"CN2K303",
"ｶﾁｯと音がするまで差込む事",
"余長は下図のように引き回す",
"CAMERAのﾗﾍﾞﾙがある方を接続する"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"検査表 :CPU BOX確認",
"LABEL の端面を当てて固定する",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "MC-Sｶﾊﾞｰ取付",
"WorkItems": [
"1. にCOVER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-①",
"WorkItems": [
"1. COVER の内側にLABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で脱脂してから貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"内側",
"内側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "背面ｶﾊﾞｰ取付",
"WorkItems": [
"1. に をBOLT BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"削除"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-②",
"WorkItems": [
"1. にLABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で脱脂してから貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "上面ｶﾊﾞｰ取付",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"配線を挟み込まないように注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-③",
"WorkItems": [
"1. にLABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :<完成品検査>ｷｯﾄ銘板"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-③",
"WorkItems": [
"1. にLABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :<完成品検査>ｷｯﾄ銘板",
"2LC-JG-23004"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り貼付出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23004",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-④",
"WorkItems": [
"1. にLABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-⑤",
"WorkItems": [
"1. にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-⑥",
"WorkItems": [
"1. にLABEL ⑦を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :<完成品検査>ｷｯﾄ銘板"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-⑥",
"WorkItems": [
"1. にLABEL ⑦を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :<完成品検査>ｷｯﾄ銘板",
"2LC-JG-23004"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り貼付出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23004",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-⑦",
"WorkItems": [
"1. にLABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾞﾗｹｯﾄﾗﾍﾞﾙ貼付け",
"WorkItems": [
"◆1. ﾗﾍﾞﾙ貼付け部の油分を除去する",
"2. STOPPER STOPPER STOPPER BRACKET へLABEL を指定の寸法で貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"15㎜",
"1㎜",
"◆作業者安全作業"
]
} | {
"QualityItem": "貼付位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "固定ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"完成図"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "固定ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"完成図"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸDﾋﾟﾝ圧入",
"WorkItems": [
"1. BLOCK にPIN を圧入"
],
"WorkPoints": [
"出代:5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "目安出代5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "40cN･m",
"WorkName": "Y軸ｾﾝｻｰ部組立",
"WorkItems": [
"1. BRACKET にSENSOR をBOLT ･WASHER ･WASHER で取付"
],
"WorkPoints": [
"L用",
"R用"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものをL･R用 3組製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸給油部組立",
"WorkItems": [
"1. BLOCK にGREASE-NIPPLE を⑯⑰⑱で取付"
],
"WorkPoints": [
"L用",
"R用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものをL･R用 3組製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸用ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"▲1. BRACKET ･BRACKET にSPACER をBOLT ･WASHER で取付しCABLE-SUPPORT を取付"
],
"WorkPoints": [
"L用",
"R用",
"側面図",
"㉖ロックタイト塗布",
"㉖ロックタイト塗布"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各2",
"この作業では同じものを3組製作"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "Y軸用ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. BRACKET ･BRACKET にSHEET を貼付",
"▲2. 1.完成品にSPACER をBOLT WASHER で取付しCABLE-SUPPORT を取付",
"3. 2.完成品に をBOLT WASHER で取付"
],
"WorkPoints": [
"L用",
"R用",
"L用",
"R用",
"L用",
"R用",
"㉗ロックタイト塗布",
"㉗ロックタイト塗布"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品 L",
"1.完成品 R",
"2.完成品 L",
"2.完成品 R",
"この作業では同じものを3組製作",
"▲特殊作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸用ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. BRACKET ･BRACKET にSHEET を貼付",
"▲2. 1.完成品にSPACER をBOLT WASHER で取付しCABLE-SUPPORT を取付",
"3. 2.完成品に をBOLT WASHER で取付"
],
"WorkPoints": [
"L用",
"R用",
"L用",
"R用",
"L用",
"R用",
"㉗ロックタイト塗布",
"㉗ロックタイト塗布"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各2",
"1.完成品 L",
"1.完成品 R",
"2.完成品 L",
"2.完成品 R",
"この作業では同じものを3組製作"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸用ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"▲1. BRACKET BRACKET にSPACER をBOLT WASHER で取付"
],
"WorkPoints": [
"L用",
"R用",
"側面図",
"㉖ロックタイト塗布",
"㉖ロックタイト塗布"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各2",
"この作業では同じものを3組製作"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "銘板貼付け",
"WorkItems": [
"1. COVER COVER にLABEL を貼付"
],
"WorkPoints": [
"L･R用各2枚作成",
"貼付け方向注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを3組製作 (A･P1･P2用)",
"P1･P2のﾗﾍﾞﾙは下記ｷｯﾄから使用の事"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3445",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3445",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P1)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P1)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3445",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P1)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3445",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P2)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P2)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3445",
"WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P2)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3445",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ部組立",
"WorkItems": [
"◆1. BEARING に㉖(グリス)を塗布",
"◆2. MOTOR-BRACKET の黄色部分に金ﾆｽを塗布",
"4. 3.完成品にSCREW SPACER を取付",
"3. 2.完成品に1.完成品を挿入しPLATE BOLT で固定",
"5. 4.完成品にSTOPPER SPACER BOLT の順で取付"
],
"WorkPoints": [
"正面合わせにて組む事(2個1組)",
"黄色部分に金ﾆｽを塗布する",
"SCREW 出代:4㎜",
"空間容積の10%~20%",
"取付向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを L用･R用 3組(6個)製作 (L･Rの区別は不要)",
"検査表MOTOR-BRACKET :◆X軸組立 ﾍﾞｱﾘﾝｸﾞへのｸﾞﾘｰｽ封入",
"ｸﾞﾘｰｽLCG100",
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"2.完成品",
"1.完成品",
"×4",
"3.完成品",
"4.完成品",
"検査表MOTOR-BRACKET :◆X軸組立 ﾍﾞｱﾘﾝｸﾞ組込",
"※ﾍﾞｱﾘﾝｸﾞ合わせ 正面合わせ",
"WWYJ-5300-048"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の10%~20%",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ部組立",
"WorkItems": [
"◆1. BEARING に㉖(グリス)を塗布",
"◆2. MOTOR-BRACKET の黄色部分に金ﾆｽを塗布",
"4. 3.完成品にSCREW SPACER を取付",
"3. 2.完成品に1.完成品を挿入しPLATE BOLT で固定",
"5. 4.完成品にSTOPPER SPACER BOLT の順で取付"
],
"WorkPoints": [
"正面合わせにて組む事(2個1組)",
"黄色部分に金ﾆｽを塗布する",
"SCREW 出代:4㎜",
"空間容積の10%~20%",
"取付向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを L用･R用 3組(6個)製作 (L･Rの区別は不要)",
"検査表MOTOR-BRACKET :◆X軸組立 ﾍﾞｱﾘﾝｸﾞへのｸﾞﾘｰｽ封入",
"ｸﾞﾘｰｽLCG100",
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"2.完成品",
"1.完成品",
"×4",
"3.完成品",
"4.完成品",
"検査表MOTOR-BRACKET :◆X軸組立 ﾍﾞｱﾘﾝｸﾞ組込",
"※ﾍﾞｱﾘﾝｸﾞ合わせ 正面合わせ"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ部組立",
"WorkItems": [],
"WorkPoints": [
"正面合わせにて組む事(2個1組)",
"SCREW 出代:4㎜",
"空間容積の10%~20%",
"取付向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.5N･m",
"WorkName": "X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ部組立",
"WorkItems": [],
"WorkPoints": [
"正面合わせにて組む事(2個1組)",
"SCREW 出代:4㎜",
"空間容積の10%~20%",
"取付向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m",
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の10%~20%",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.5N･m",
"WorkName": "X・Y軸ﾎﾞｰﾙﾈｼﾞ可動部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾎﾞｰﾙﾈｼﾞ部組立",
"WorkItems": [
"1. BALL-SCREW の重要部品の確認を行う",
"3. 2.完成品にJOINT を取付",
"2. BALL-SCREW のねじ部の防錆油をふき取り､取付け面に砥石をかける",
"4. に3.完成品を仮固定",
"5. 4.完成品にBEARING を挿入しC-RING で固定"
],
"WorkPoints": [
"JOINT の位置に注意",
"L用･R用区別の為ﾏｽｷﾝｸﾞﾃｰﾌﾟで明記の事",
"型式確認及び､ｼﾘｱﾙ№記録",
"BALL-SCREW の黄色面に砥石を掛ける事",
"本締工程:SD-A044836-024",
"C-RINGの取付方向はR側が内側になる様にする事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×6",
"この作業では同じものを3組製作 (A･P1･P2用 L･R区分)",
"検査表BALL-SCREW :部品確認",
"2.完成品",
"3.完成品",
"WWYJ-5300-048"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾎﾞｰﾙﾈｼﾞ部組立",
"WorkItems": [
"1. BALL-SCREW の重要部品の確認を行う",
"3. 2.完成品にJOINT を取付",
"2. BALL-SCREW のねじ部の防錆油をふき取り､取付け面に砥石をかける",
"4. に3.完成品を仮固定",
"5. 4.完成品にBEARING を挿入しC-RING で固定"
],
"WorkPoints": [
"JOINT の位置に注意",
"L用･R用区別の為ﾏｽｷﾝｸﾞﾃｰﾌﾟで明記の事",
"型式確認及び､ｼﾘｱﾙ№記録",
"BALL-SCREW の黄色面に砥石を掛ける事",
"本締工程:SD-A044836-024",
"C-RINGの取付方向はR側が内側になる様にする事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×6",
"この作業では同じものを3組製作 (A･P1･P2用 L･R区分)",
"検査表BALL-SCREW :部品確認",
"2.完成品",
"3.完成品",
"WWYJ-5300-048"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.2N･m",
"WorkName": "X軸ﾎﾞｰﾙﾈｼﾞ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾎﾞｰﾙﾈｼﾞ部組立",
"WorkItems": [
"1. BALL-SCREW の重要部品の確認を行う",
"3. 2.完成品にJOINT ･JOINT を取付",
"2. BALL-SCREW のねじ部の防錆油をふき取り､取付け面に砥石をかける",
"4. 3.完成品にTUBE を挿入",
"5. に4.完成品を仮固定",
"6. 5.完成品にBEARING を挿入しC-RING で固定"
],
"WorkPoints": [
"JOINT の位置に注意",
"L用･R用区別の為ﾏｽｷﾝｸﾞﾃｰﾌﾟで明記の事",
"型式確認及び､ｼﾘｱﾙ№記録",
"BALL-SCREW の黄色面に砥石を掛ける事",
"本締工程:SD-A044836-032",
"C-RINGの取付方向はR側が内側になる様にする事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "WWYJ-5300-048",
"InspectionItems": [
"検査表BALL-SCREW :部品確認"
],
"WorkTypes": [],
"Words": [
"×4",
"この作業では同じものを3組製作 (A･P1･P2用 L･R区分)",
"2.完成品",
"3.完成品",
"WWYJ-5300-048"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾎﾞｰﾙﾈｼﾞ部組立",
"WorkItems": [
"1. BALL-SCREW の重要部品の確認を行う",
"3. 2.完成品にJOINT ･JOINT を取付",
"2. BALL-SCREW のねじ部の防錆油をふき取り､取付け面に砥石をかける",
"4. 3.完成品にTUBE を挿入",
"5. に4.完成品を仮固定",
"6. 5.完成品にBEARING を挿入しC-RING で固定"
],
"WorkPoints": [
"JOINT の位置に注意",
"L用･R用区別の為ﾏｽｷﾝｸﾞﾃｰﾌﾟで明記の事",
"型式確認及び､ｼﾘｱﾙ№記録",
"BALL-SCREW の黄色面に砥石を掛ける事",
"本締工程:SD-A044836-032",
"C-RINGの取付方向はR側が内側になる様にする事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "WWYJ-5300-048",
"InspectionItems": [
"検査表BALL-SCREW :部品確認"
],
"WorkTypes": [],
"Words": [
"×4",
"この作業では同じものを3組製作 (A･P1･P2用 L･R区分)",
"2.完成品",
"3.完成品",
"WWYJ-5300-048"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "1.2N･m",
"WorkName": "Y軸ﾎﾞｰﾙﾈｼﾞ部組立",
"WorkItems": [
"1. BALL-SCREW の重要部品の確認を行う",
"3. 2.完成品にJOINT ･JOINT を取付",
"2. BALL-SCREW のねじ部の防錆油をふき取り､取付け面に砥石をかける",
"4. 3.完成品にTUBE を挿入",
"5. に4.完成品を仮固定",
"6. 5.完成品にBEARING を挿入しC-RING で固定"
],
"WorkPoints": [
"L用･R用区別の為ﾏｽｷﾝｸﾞﾃｰﾌﾟで明記の事",
"型式確認及び､ｼﾘｱﾙ№記録",
"BALL-SCREW の黄色面に砥石を掛ける事",
"本締工程:SD-A044836-032"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを3組製作 (A･P1･P2用 L･R区分)",
"検査表BALL-SCREW :部品確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Yﾃｰﾌﾞﾙ取付ﾌﾟﾚｰﾄ部組立①",
"WorkItems": [
"1. PLATE にPIN を取付",
"2. 1.完成品にTUBE-HOLDER ･JOINT をSCREW ･BOLT ･WASHER ･WASHER で取付",
"3. 2.完成品にTUBE ･TUBE ･TUBE ･TUBE を取付"
],
"WorkPoints": [
"R用",
"L用",
"側面図",
"裏面図",
"R用",
"L用",
"裏面図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを L用･R用 3組(6個)製作",
"1.完成品",
"出代:5mm",
"2.完成品"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾃｰﾌﾞﾙ取付ﾌﾟﾚｰﾄ部組立②",
"WorkItems": [
"1. にDOG をBOLT WASHER で取付",
"2. 1.完成品にDOG SENSOR をBOLT WASHER BOLT WASHER ㉒で取付"
],
"WorkPoints": [
"R用",
"L用",
"側面図",
"R用",
"L用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを L用･R用 3組(6個)製作",
"1.完成品",
"×8",
"2.完成品",
"×2",
"×2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Zθﾃｰﾌﾞﾙ取付ﾌﾟﾚｰﾄ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:2.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XY組立ﾍﾞｰｽ",
"Size": "",
"ToolOther": "FM-3506",
"WorkName": "X軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3506",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.9N･m",
"WorkName": "X軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "作業指示の寸法である事",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "22㎜",
"ToolOther": "8.7N･m",
"WorkName": "X軸ﾌﾚｰﾑ部組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 8.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :◆X軸組立 ﾎﾞｰﾙﾈｼﾞへのﾍﾞｱﾘﾝｸﾞ組付",
"WWYJ-5300-048"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "8.7N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "X軸ﾎﾞｰﾙﾈｼﾞ:0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "Y軸ﾎﾞｰﾙﾈｼﾞ:0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-048"
]
} | {
"QualityItem": "水平度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "ｽﾗｽﾄｶﾞﾀ0.001㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-048",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.