input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "N605:ﾌﾚｰﾑLﾅｯﾄ挿入",
"WorkItems": [
"1. FRAME に②を取付ける"
],
"WorkPoints": [
"左側を基準にしてﾅｯﾄの位置を決めていく事",
"L-c面",
"L-b面",
"L-a面",
"L-d面",
"L-d面 0個",
"L-a面 1個",
"L-b面 0個",
"L-c面 3個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "N613:ﾌﾚｰﾑMﾅｯﾄ挿入",
"WorkItems": [
"1. FRAME に②を取付ける"
],
"WorkPoints": [
"左側を基準にしてﾅｯﾄの位置を決めていく事",
"M-c面",
"M-b面",
"M-a面",
"M-d面",
"M-c面 0個",
"M-a面 1個",
"M-b面 2個",
"M-c面 1個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "N613:ﾌﾚｰﾑNﾅｯﾄ挿入",
"WorkItems": [
"1. FRAME に②を取付ける"
],
"WorkPoints": [
"左側を基準にしてﾅｯﾄの位置を決めていく事",
"N-c面",
"N-b面",
"N-a面",
"N-d面",
"N-a面 0個",
"N-b面 1個",
"N-c面 1個",
"N-d面 1個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "N612:ﾌﾚｰﾑOﾅｯﾄ挿入",
"WorkItems": [
"1. FRAME に②を取付ける"
],
"WorkPoints": [
"左側を基準にしてﾅｯﾄの位置を決めていく事",
"O-a面 4個",
"O-c面 2個",
"O-c面",
"O-b面",
"O-a面",
"O-d面",
"O-b面 0個",
"O-d面 0個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"▲特殊作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "接着剤ｽｰﾊﾟｰX",
"WorkName": "N612:ﾌﾚｰﾑOﾅｯﾄ挿入",
"WorkItems": [
"▲2. １の完成品にCAP を㉗で接着する"
],
"WorkPoints": [
"接着剤は外にはみ出ない様に内側に塗布する事｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"接着剤塗布 米粒:3",
"▲特殊作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:3",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "N604:ﾌﾚｰﾑPﾅｯﾄ挿入",
"WorkItems": [
"1. FRAME に②を取付ける"
],
"WorkPoints": [
"左側を基準にしてﾅｯﾄの位置を決めていく事",
"P-c面",
"P-b面",
"P-a面",
"P-d面",
"P-a面 1個",
"P-b面 0個",
"P-c面 3個",
"P-d面 2個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "N609:ﾌﾚｰﾑQﾅｯﾄ挿入",
"WorkItems": [
"1. FRAME に②を取付ける",
"2. 1の完成品にTAPE を貼付ける"
],
"WorkPoints": [
"左側を基準にしてﾅｯﾄを挿入していく事",
"左側",
"右側",
"前側",
"後側",
"Q-b面(後側) 1個",
"Q-c面(下側) 1個",
"Q-d面(前側) 1個",
"Q-a面(上側) 1個",
"脱脂して貼付けること｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Q-c",
"Q-b",
"Q-a",
"Q-d",
"◆作業者安全作業",
"2mm",
"100mm",
"35mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保護ﾒｶﾞﾈ",
"Size": "",
"ToolOther": "",
"WorkName": "N609:ﾌﾚｰﾑQﾅｯﾄ挿入",
"WorkItems": [],
"WorkPoints": [
"Q-b面(後側) 1個",
"Q-c面(下側) 1個",
"Q-d面(前側) 1個",
"Q-a面(上側) 1個",
"脱脂して貼付けること｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2mm",
"100mm",
"35mm",
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "N610:ﾌﾚｰﾑRﾅｯﾄ挿入",
"WorkItems": [
"1. FRAME に②を取付ける"
],
"WorkPoints": [
"上側を基準にしてﾅｯﾄを挿入していく事",
"R-d面(前側) 1個",
"R-c面(右側) 1個",
"R-a面(左側) 1個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"▲特殊作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "接着剤ｽｰﾊﾟｰX",
"WorkName": "N610:ﾌﾚｰﾑRﾅｯﾄ挿入",
"WorkItems": [
"▲2. １の完成品にCAP を㉗で接着する"
],
"WorkPoints": [
"接着剤は外にはみ出ない様に内側に塗布する事｡",
"上側へ取付ける",
"左側",
"右側",
"前側",
"後側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"接着剤塗布 米粒:各3",
"R-c",
"R-a",
"R-d",
"R-b",
"▲特殊作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:3",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "N609:ﾌﾚｰﾑSﾅｯﾄ挿入",
"WorkItems": [
"1. FRAME に②を取付ける"
],
"WorkPoints": [
"左側を基準にしてﾅｯﾄの位置を決めていく事",
"S-c面 2個",
"S-c面",
"S-b面",
"S-a面",
"S-d面",
"S-a面 2個",
"S-b面 0個",
"S-d面 0個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立①",
"WorkItems": [
"1. ①②③④をBRACKET BOLT で取付ける"
],
"WorkPoints": [
"定盤とﾌﾚｰﾑの間に隙間が無いこと",
"BRACKETの突起部を→方向に取付ける",
"ﾗｲﾝに歪みが無いことを確認",
"突起部方向",
"事前に取付けしたﾅｯﾄへﾌﾞﾗｹｯﾄを取付",
"A-b面",
"A-c面",
"D-b面",
"D-c面",
"B-b面",
"C-c面",
"C-b面",
"B-c面"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績表",
"StdVal": "指示通り取付け出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾚｰﾑ組立①",
"WorkItems": [
"1. ①②③④をBRACKET BOLT で取付ける"
],
"WorkPoints": [
"定盤とﾌﾚｰﾑの間に隙間が無いこと",
"BRACKETの突起部を→方向に取付ける",
"ﾗｲﾝに歪みが無いことを確認",
"突起部方向",
"事前に取付けしたﾅｯﾄへﾌﾞﾗｹｯﾄを取付",
"A-b面",
"A-c面",
"D-b面",
"D-c面",
"B-b面",
"C-c面",
"C-b面",
"B-c面"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾚｰﾑ組立②",
"WorkItems": [
"1. ①②③④をBRACKET BOLT で取付ける"
],
"WorkPoints": [
"L-a面",
"事前に取付けしたﾅｯﾄへﾌﾞﾗｹｯﾄを取付",
"B-b面",
"L-d面",
"F-a面",
"F-d面",
"G-d面(下面)",
"BRACKETの突起部を→方向に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾚｰﾑ組立③",
"WorkItems": [
"1. ①に②③をBRACKET BOLT で取付ける"
],
"WorkPoints": [
"BRACKETの突起部を→方向に取付ける",
"事前に取付けしたﾅｯﾄへﾌﾞﾗｹｯﾄを取付",
"K-d面",
"K-c面",
"L-d面",
"L-c面"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾚｰﾑ組立④",
"WorkItems": [
"1. ①に②③④をBRACKET BOLT で取付ける"
],
"WorkPoints": [
"BRACKETの突起部を→方向に取付ける",
"事前に取付けしたﾅｯﾄへﾌﾞﾗｹｯﾄを取付",
"BRACKET は丸部分が違うので注意",
"H-c面",
"H-b面",
"J-b面",
"J-c面",
"I-c面",
"I-b面"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾚｰﾑ組立⑤",
"WorkItems": [
"1. ①に②③④をBRACKET BOLT で取付ける"
],
"WorkPoints": [
"BRACKETの突起部を→方向に取付ける",
"事前に取付けしたﾅｯﾄへﾌﾞﾗｹｯﾄを取付",
"M-d面",
"M-a面",
"N-d面",
"N-a面",
"O-d面",
"O-a面"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾚｰﾑ組立⑥",
"WorkItems": [
"1. ①に②③④⑤をBRACKET BOLT で取付ける"
],
"WorkPoints": [
"Q-b面",
"Q-a面",
"R-d面",
"S-b面",
"S-a面",
"BRACKETの突起部を→方向に取付ける",
"事前に取付けしたﾅｯﾄへﾌﾞﾗｹｯﾄを取付"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｷｬｽﾀｰ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"CASTERの傾き･段差等無いことを確認｡",
"隙間を均等にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"400㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ｷｬｽﾀｰ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"CASTERの傾き･段差等無いことを確認｡",
"隙間を均等にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"400㎜"
]
} | {
"QualityItem": "段差確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "P612ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保護ﾒｶﾞﾈ",
"Size": "",
"ToolOther": "",
"WorkName": "P604､P605ﾎﾙﾀﾞｰ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P604､P605ﾎﾙﾀﾞｰ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "P604､P605ﾎﾙﾀﾞｰ取付",
"WorkItems": [
"3. ①に1.2.の完成品をBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保護ﾒｶﾞﾈ",
"Size": "",
"ToolOther": "",
"WorkName": "P603ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. BRACKET にCOVER TAPE ⑤⑥を貼付ける"
],
"WorkPoints": [
"脱脂して貼付けること",
"端面に合わせて貼付ける",
"端面に合わせて貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"115mm",
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P603ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. BRACKET にCOVER TAPE ⑤⑥を貼付ける"
],
"WorkPoints": [
"脱脂して貼付けること",
"端面に合わせて貼付ける",
"端面に合わせて貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"115mm",
"◆作業者安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "P603ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. ①に1.の完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "P601ﾎﾙﾀﾞｰ取付",
"WorkItems": [
"1. ①にHOLDER をBOLT WASHER で取付ける｡",
"2. 1.の完成品にBOX を置く｡"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保護ﾒｶﾞﾈ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ前準備1",
"WorkItems": [
"1. BRACKET にTAPE を､BRACKET にTAPE を､BRACKET にTAPE を下記寸法で貼付ける｡",
"2. 1.の完成品にCOVER COVER を取付ける｡",
"1. BRACKET にTAPE を､BRACKET にTAPE を､BRACKET にTAPE を下記寸法で貼付ける｡",
"2. 1.の完成品にCOVER COVER を取付ける｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"5mm",
"5mm",
"◆作業者安全作業",
"5mm",
"5mm",
"5mm"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ前準備1",
"WorkItems": [
"1. BRACKET にTAPE を､BRACKET にTAPE を､BRACKET にTAPE を下記寸法で貼付ける｡",
"2. 1.の完成品にCOVER COVER を取付ける｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"5mm",
"5mm",
"◆作業者安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付1",
"WorkItems": [
"1. ①に②③をBOLT WASHER で④をWASHER WASHER で取付ける｡"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保護ﾒｶﾞﾈ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ前準備2",
"WorkItems": [
"1. BRACKET にTAPE を下記寸法で貼付ける｡",
"2. 1.の完成品にCOVER を取付け､LABEL ⑤を下記寸法で貼付ける｡"
],
"WorkPoints": [
"脱脂する事",
"脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"2mm",
"◆作業者安全作業",
"2mm",
"10mm",
"10mm",
"6mm",
"25mm",
"67mm"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ前準備2",
"WorkItems": [
"1. BRACKET にTAPE を下記寸法で貼付ける｡",
"2. 1.の完成品にCOVER を取付け､LABEL ⑤を下記寸法で貼付ける｡"
],
"WorkPoints": [
"脱脂する事",
"脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"2mm",
"◆作業者安全作業",
"2mm",
"10mm",
"10mm",
"6mm",
"25mm",
"67mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保護ﾒｶﾞﾈ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ前準備3",
"WorkItems": [
"1. BRACKET にTAPE をBRACKET にTAPE を下記寸法で貼付ける｡",
"2. 1.の完成品にCOVER COVER を取付ける｡"
],
"WorkPoints": [
"脱脂する事",
"脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"5mm",
"端面に合わせる",
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ前準備3",
"WorkItems": [
"1. BRACKET にTAPE をBRACKET にTAPE を下記寸法で貼付ける｡",
"2. 1.の完成品にCOVER COVER を取付ける｡"
],
"WorkPoints": [
"脱脂する事",
"脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"5mm",
"端面に合わせる",
"◆作業者安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付2",
"WorkItems": [
"1. ①に②③④をBOLT WASHER で取付ける｡"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"WorkItems": [],
"WorkPoints": [
"合わせて作業№1で仮取付けしたBOLT も本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "20N･m",
"WorkName": "ｸﾞﾘｯﾌﾟ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 20N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各20N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｸﾞﾘｯﾌﾟ取付",
"WorkItems": [
"1. GRIP にPLATE をWASHER NUT で取付ける｡",
"1. ①に上記完成品をBOLT WASHER で取付ける｡"
],
"WorkPoints": [
"2ヶ製作"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立1",
"WorkItems": [
"1. COUPLER にLABEL FGﾗﾍﾞﾙを貼付け"
],
"WorkPoints": [
"貼付け面の清掃及び油分を除去"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立1",
"WorkItems": [
"2. 1完成品にJOINT を取付",
"◆3. JOINT 取付時に発生するｼｰﾙのｶｽをｴｱﾌﾞﾛｰにて取り除く"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾌﾟﾗｰ回り止め治具",
"Size": "",
"ToolOther": "FM-3902",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立1",
"WorkItems": [
"2. 1完成品にJOINT を取付",
"◆3. JOINT 取付時に発生するｼｰﾙのｶｽをｴｱﾌﾞﾛｰにて取り除く"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3902",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立1",
"WorkItems": [
"1. COUPLER にLABEL FGﾗﾍﾞﾙを貼付け",
"2. 1完成品にJOINT を取付",
"◆3. JOINT 取付時に発生するｼｰﾙのｶｽをｴｱﾌﾞﾛｰにて取り除く"
],
"WorkPoints": [
"貼付け面の清掃及び油分を除去",
"保護ﾒｶﾞﾈ着用"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾐ､埃が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立2",
"WorkItems": [
"■2. FG線をSCREW にて取付",
"■1. ①にCABLE を設置してSCREW WASHER にて取付"
],
"WorkPoints": [
"【注意】 CABLE の取付方向(ｺﾈｸﾀｰの向き)あり"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "GWETJ-F013-002",
"InspectionItems": [
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立2",
"WorkItems": [
"■2. FG線をSCREW にて取付",
"■1. ①にCABLE を設置してSCREW WASHER にて取付"
],
"WorkPoints": [
"【注意】 CABLE の取付方向(ｺﾈｸﾀｰの向き)あり"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "GWETJ-F013-002",
"InspectionItems": [
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾗｹｯﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-5611",
"WorkName": "ﾊﾞﾙﾌﾞ組立1",
"WorkItems": [
"1. MANIFOLD にBRACKET BRACKET をBOLT WASHER にて仮取付",
"2. ㉗治具に１完成品を取付",
"4. ﾌﾞﾗｹｯﾄを固定",
"4. ﾌﾞﾗｹｯﾄを固定"
],
"WorkPoints": [
"左側のｽﾄｯﾊﾟｰに当てつけて固定",
"治具付属ﾎﾞﾙﾄを使用",
"ﾌﾞﾗｹｯﾄ固定後､治具から取り外す",
"ﾌﾞﾗｹｯﾄ固定後､治具から取り外す"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"【注意】 BRACKET BRACKET の取付間違え無き事",
"BRACKET BRACKET ﾌﾞﾗｹｯﾄの穴が上側になるように取付",
"BRACKET BRACKET ﾌﾞﾗｹｯﾄの穴が上側になるように取付"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5611",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾊﾞﾙﾌﾞ組立1",
"WorkItems": [
"4. ﾌﾞﾗｹｯﾄを固定"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ固定後､治具から取り外す"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"BRACKET BRACKET ﾌﾞﾗｹｯﾄの穴が上側になるように取付"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-(7㎜)",
"ToolOther": "110cN･m",
"WorkName": "ﾊﾞﾙﾌﾞ組立2",
"WorkItems": [
"1. ①にJOINT を取付"
],
"WorkPoints": [
"JOINT の取付角度は略図を参照"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"K004-1"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-(7㎜)",
"ToolOther": "110cN･m",
"WorkName": "ﾊﾞﾙﾌﾞ組立2",
"WorkItems": [
"1. ①にJOINT を取付"
],
"WorkPoints": [
"JOINT の取付角度は略図を参照"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"K004-1"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾓｰﾀ配線ﾌﾞﾗｹｯﾄ組立1",
"WorkItems": [
"1. BUSH を4個目でｶｯﾄ",
"3. PLATE PLATE に2完成品を取付",
"2. 1完成品に折り曲げｸｾを付ける"
],
"WorkPoints": [
"【注意】 接着面に触れ無い事",
"BUSH は確実に取付の事",
"1個目を矢印方向に折り曲げて､ｸｾを付ける",
"貼付け面の油分を除去"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾘﾆｱﾓｰﾀ配線ﾌﾞﾗｹｯﾄ組立2",
"WorkItems": [
"3. BRACKET に1完成品とSPACER をBOLT WASHER にて取付",
"3. BRACKET に1完成品とSPACER をBOLT WASHER にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾘﾆｱﾓｰﾀ配線ﾌﾞﾗｹｯﾄ組立2",
"WorkItems": [
"3. BRACKET に1完成品とSPACER をBOLT WASHER にて取付",
"3. BRACKET に1完成品とSPACER をBOLT WASHER にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "BOX5㎜",
"ToolOther": "60cN･m",
"WorkName": "基板ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にCOVER をSPACER にて取付"
],
"WorkPoints": [
"COVER の表裏無し",
"【組立目安】 3部品が真っすぐになる様に組立"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にCOVER をSPACER にて取付"
],
"WorkPoints": [
"COVER の表裏無し",
"【組立目安】 3部品が真っすぐになる様に組立"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾓｰﾀ組立1",
"WorkItems": [
"2. BLOCK にPIN を圧入",
"◆1. BLOCK のﾊﾞﾘ･打痕の確認"
],
"WorkPoints": [
"【組立目安】 PIN の出代 1.5mm±0.2mm",
"保護ﾒｶﾞﾈ着用",
"この作業では同じものを8個確認",
"PIN はﾃｰﾊﾟ側を圧入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾃｰﾊﾟ側",
"この作業では同じものを8個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕等が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "D-PIN圧入治具",
"Size": "",
"ToolOther": "FM-5720",
"WorkName": "ﾘﾆｱﾓｰﾀ組立1",
"WorkItems": [
"2. BLOCK にPIN を圧入",
"◆1. BLOCK のﾊﾞﾘ･打痕の確認"
],
"WorkPoints": [
"【組立目安】 PIN の出代 1.5mm±0.2mm",
"保護ﾒｶﾞﾈ着用",
"この作業では同じものを8個確認",
"PIN はﾃｰﾊﾟ側を圧入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾃｰﾊﾟ側",
"この作業では同じものを8個製作",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5720",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.2㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾓｰﾀ組立1",
"WorkItems": [
"2. BLOCK にPIN を圧入",
"◆1. BLOCK のﾊﾞﾘ･打痕の確認"
],
"WorkPoints": [
"【組立目安】 PIN の出代 1.5mm±0.2mm",
"保護ﾒｶﾞﾈ着用",
"この作業では同じものを8個確認",
"PIN はﾃｰﾊﾟ側を圧入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾃｰﾊﾟ側",
"この作業では同じものを8個製作",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾓｰﾀ組立2",
"WorkItems": [
"■1. MOTOR の型式確認･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"▲2. BOLT にﾛｯｸﾀｲﾄを塗布し､MOTOR に②をBOLT にて取付",
"3. 取付後の摺動確認"
],
"WorkPoints": [
"Z軸ﾓｰﾀ型式:DM08GG011A37CXP0",
"略図の様に㉘治具を取付て、ブロックが治具に沿うように締結する",
"Z軸ﾓｰﾀｰを静かに上下を反転させ､軸が自重で動くことを確認"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "GWETJ-F013-001",
"InspectionItems": [
"検査表MOTOR :Z軸ﾓｰﾀｰ型式確認"
],
"WorkTypes": [],
"Words": [
"検査表MOTOR :Z軸ﾓｰﾀｰｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"接着剤塗布 ｺﾞﾏ粒:各1",
"検査表MOTOR :Z軸ﾓｰﾀｰの摺動確認",
"GWETJ-F013-001"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "GWETJ-F013-001",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾓｰﾀ組立2",
"WorkItems": [
"■1. MOTOR の型式確認･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"▲2. BOLT にﾛｯｸﾀｲﾄを塗布し､MOTOR に②をBOLT にて取付",
"3. 取付後の摺動確認"
],
"WorkPoints": [
"Z軸ﾓｰﾀ型式:DM08GG011A37CXP0",
"略図の様に㉘治具を取付て、ブロックが治具に沿うように締結する",
"Z軸ﾓｰﾀｰを静かに上下を反転させ､軸が自重で動くことを確認"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表MOTOR :Z軸ﾓｰﾀｰ型式確認",
"検査表MOTOR :Z軸ﾓｰﾀｰｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"接着剤塗布 ｺﾞﾏ粒:各1",
"検査表MOTOR :Z軸ﾓｰﾀｰの摺動確認"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾘﾆｱﾓｰﾀ組立2",
"WorkItems": [
"■1. MOTOR の型式確認･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"▲2. BOLT にﾛｯｸﾀｲﾄを塗布し､MOTOR に②をBOLT にて取付",
"3. 取付後の摺動確認"
],
"WorkPoints": [
"Z軸ﾓｰﾀ型式:DM08GG011A37CXP0",
"略図の様に㉘治具を取付て、ブロックが治具に沿うように締結する",
"Z軸ﾓｰﾀｰを静かに上下を反転させ､軸が自重で動くことを確認"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表MOTOR :Z軸ﾓｰﾀｰ型式確認",
"検査表MOTOR :Z軸ﾓｰﾀｰｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"接着剤塗布 ｺﾞﾏ粒:各1",
"検査表MOTOR :Z軸ﾓｰﾀｰの摺動確認",
"■安全作業",
"▲特殊作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱﾓｰﾀﾌﾞﾛｯｸ角度合わせｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5722",
"WorkName": "ﾘﾆｱﾓｰﾀ組立2",
"WorkItems": [
"■1. MOTOR の型式確認･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"▲2. BOLT にﾛｯｸﾀｲﾄを塗布し､MOTOR に②をBOLT にて取付",
"3. 取付後の摺動確認"
],
"WorkPoints": [
"Z軸ﾓｰﾀ型式:DM08GG011A37CXP0",
"略図の様に㉘治具を取付て、ブロックが治具に沿うように締結する",
"Z軸ﾓｰﾀｰを静かに上下を反転させ､軸が自重で動くことを確認"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表MOTOR :Z軸ﾓｰﾀｰ型式確認",
"検査表MOTOR :Z軸ﾓｰﾀｰｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"接着剤塗布 ｺﾞﾏ粒:各1",
"検査表MOTOR :Z軸ﾓｰﾀｰの摺動確認",
"■安全作業",
"▲特殊作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5722",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾓｰﾀ組立2",
"WorkItems": [
"■1. MOTOR の型式確認･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"▲2. BOLT にﾛｯｸﾀｲﾄを塗布し､MOTOR に②をBOLT にて取付",
"3. 取付後の摺動確認"
],
"WorkPoints": [
"Z軸ﾓｰﾀ型式:DM08GG011A37CXP0",
"略図の様に㉘治具を取付て、ブロックが治具に沿うように締結する",
"Z軸ﾓｰﾀｰを静かに上下を反転させ､軸が自重で動くことを確認"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "GWETJ-F013-001",
"InspectionItems": [
"検査表MOTOR :Z軸ﾓｰﾀｰｼﾘｱﾙﾅﾝﾊﾞｰ確認"
],
"WorkTypes": [],
"Words": [
"検査表MOTOR :Z軸ﾓｰﾀｰ型式確認",
"接着剤塗布 ｺﾞﾏ粒:各1",
"検査表MOTOR :Z軸ﾓｰﾀｰの摺動確認",
"GWETJ-F013-001"
]
} | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "自重で動く事",
"Method": "目視",
"RecordMethod": "GWETJ-F013-001",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾓｰﾀ組立2",
"WorkItems": [
"■1. MOTOR の型式確認･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"▲2. BOLT にﾛｯｸﾀｲﾄを塗布し､MOTOR に②をBOLT にて取付",
"3. 取付後の摺動確認"
],
"WorkPoints": [
"Z軸ﾓｰﾀ型式:DM08GG011A37CXP0",
"略図の様に㉘治具を取付て、ブロックが治具に沿うように締結する",
"Z軸ﾓｰﾀｰを静かに上下を反転させ､軸が自重で動くことを確認"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表MOTOR :Z軸ﾓｰﾀｰ型式確認",
"検査表MOTOR :Z軸ﾓｰﾀｰｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"接着剤塗布 ｺﾞﾏ粒:各1",
"検査表MOTOR :Z軸ﾓｰﾀｰの摺動確認"
]
} | {
"QualityItem": "ｸﾞﾘｰｽ拭取り確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り拭取り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜BOX",
"ToolOther": "100cN･m",
"WorkName": "ﾘﾆｱﾓｰﾀ組立3",
"WorkItems": [
"1. ①に②③をSPACER にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "ﾘﾆｱﾓｰﾀ組立4",
"WorkItems": [
"1. ①にCABLE-SUPPORT をBOLT にて取付"
],
"WorkPoints": [
"【注意】 CABLE-SUPPORT の取付方向 ※(下略図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立1",
"WorkItems": [
"◆2. 細部に清掃ﾌﾞﾛｰ実施",
"1. HEAD PLATE のﾊﾞﾘ･打痕の確認"
],
"WorkPoints": [
"【注意】 保護ﾒｶﾞﾈ着用",
"全体的に確認するが取付面(青色部分)は特に注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表面",
"裏面"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕等が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立2",
"WorkItems": [
"1. ①の貼付面の脱脂を実施 ※略図青枠部分",
"2. 略図の位置に製造ｼﾘｱﾙ銘板を貼付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "D-PIN圧入治具",
"Size": "",
"ToolOther": "FM-5720",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立3",
"WorkItems": [
"1. ①にPIN を圧入"
],
"WorkPoints": [
"【組立目安】 ﾋﾟﾝの出代 3mm±0.2mm",
"PIN はﾃｰﾊﾟ側を圧入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾃｰﾊﾟ側"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5720",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.2㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立3",
"WorkItems": [
"1. ①にPIN を圧入"
],
"WorkPoints": [
"【組立目安】 ﾋﾟﾝの出代 3mm±0.2mm",
"PIN はﾃｰﾊﾟ側を圧入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾃｰﾊﾟ側"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立4",
"WorkItems": [
"1. ①にCLIP をBOLT にて取付"
],
"WorkPoints": [
"CLIP の取付方向に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立5",
"WorkItems": [
"1. ①にJOINT をBOLT WASHER WASHER にて取付",
"2. 1完成品にJOINT を取付"
],
"WorkPoints": [
"JOINT は確実に奥まで差込む事"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立6",
"WorkItems": [
"1. ①にJOINT をBOLT WASHER WASHER にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ取付7",
"WorkItems": [
"2. 1完成品にPOST を取付"
],
"WorkPoints": [
"止めﾈｼﾞが動かないようにﾚﾝﾁで押さえて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "2.7N･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立8",
"WorkItems": [
"1. ①にWASHER SPACER をBOLT にて取付"
],
"WorkPoints": [
"SPACER を黄色矢印方向に押しつけながらBOLT を締結"
],
"Tolks": [
"締付ﾄﾙｸ 2.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.7N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER にて仮取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "位置合せ治具",
"Size": "",
"ToolOther": "FM-5694",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5694",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T20",
"ToolOther": "194cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｴｱﾁｭｰﾌﾞ接続",
"WorkItems": [
"1. TUBE TUBE を指示長さにｶｯﾄする",
"2. ①に1完成品ﾁｭｰﾌﾞを接続する"
],
"WorkPoints": [
"挿入時､ﾁｭｰﾌﾞが折れない様に注意",
"挿入場所に注意(略図参照)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"80mm",
"70mm",
"70mm",
"70mm",
"80mm",
"70mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾘﾆｱﾓｰﾀ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾄﾞﾛｱ配線は略図赤線の様に引き回しておく",
"ﾋﾟﾝに嵌合させる"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150cm",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾙ周辺取付",
"WorkItems": [],
"WorkPoints": [
"油分を除去してから貼付け"
],
"Tolks": [
"BOLT ﾎﾞﾙﾄ 締付ﾄﾙｸ 100cN･m",
"BOLT BOLT ﾎﾞﾙﾄ 締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾊﾝﾄﾞﾙ周辺取付",
"WorkItems": [],
"WorkPoints": [
"油分を除去してから貼付け"
],
"Tolks": [
"BOLT ﾎﾞﾙﾄ 締付ﾄﾙｸ 100cN･m",
"BOLT BOLT ﾎﾞﾙﾄ 締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾊﾝﾄﾞﾙ周辺取付",
"WorkItems": [],
"WorkPoints": [
"油分を除去してから貼付け"
],
"Tolks": [
"BOLT ﾎﾞﾙﾄ 締付ﾄﾙｸ 100cN･m",
"BOLT BOLT ﾎﾞﾙﾄ 締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾊﾝﾄﾞﾙ周辺取付",
"WorkItems": [],
"WorkPoints": [
"油分を除去してから貼付け"
],
"Tolks": [
"BOLT ﾎﾞﾙﾄ 締付ﾄﾙｸ 100cN･m",
"BOLT BOLT ﾎﾞﾙﾄ 締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "基板ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER にて取付"
],
"WorkPoints": [
"【取付目安】 目視にてﾌﾚｰﾑと傾きがない様に取付",
"【取付目安】 目視にてﾌﾚｰﾑと傾きがない様に取付"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ1",
"WorkItems": [
"◆1. NOZZLE HOLDER に清掃ﾌﾞﾛｰ実施"
],
"WorkPoints": [
"細部まで清掃ﾌﾞﾛｰを実施して､流路にあるｺﾞﾐや異物を完全に除去する",
"保護ﾒｶﾞﾈ着用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"穴部",
"穴部",
"凹部",
"凹部",
"この作業では同じものを8個製作",
"全体に清掃ﾌﾞﾛｰを実施してｺﾞﾐや異物を除去する",
"全ての流路にも清掃ﾌﾞﾛｰを実施する",
"全数(8個)実施"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾐ､埃が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ2",
"WorkItems": [
"◆1. SPRING(BLACK) 端部の輪を引っ掛け､ﾘﾝｸﾞ状にする",
"◆2. CLAMP-ARM(BLACK) 先端部の溝部へｸﾞﾘｰｽを塗布する",
"◆3. 2完成品を㉚治具にセットし、グリスを塗布する",
"4. ㉛治具に③を8個セットする",
"◆5. 4完成品の指定箇所にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"SPRING(BLACK) 端部の輪を引っ掛ける",
"保護ﾒｶﾞﾈ着用",
"この作業では同じものを8個製作",
"この作業では同じものを16個製作",
"この作業では同じものを8個製作",
"この作業では同じものを16個製作",
"写真の様に設置する",
"溝部以外の余分なｸﾞﾘｰｽは拭取る"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"溝部に確実に入るようにｸﾞﾘｰｽを塗布すること",
"溝部",
"㉚ FM-5845",
"㉛ FM-5765",
"ｸﾞﾘｰｽ塗布位置",
"ｸﾞﾘｰｽ塗布位置 (反対側にもあり)",
"検査表SPRING(BLACK) :ｸﾗﾝﾌﾟｱｰﾑ ｸﾞﾘｰｽ塗布",
"検査表SPRING(BLACK) :ｸﾗﾝﾌﾟｱｰﾑ ｸﾞﾘｰｽ塗布",
"ｸﾞﾘｰｽ塗布位置",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(1個につき)",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(1個につき)",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:2(1個につき2箇所)",
"ﾋﾝｼﾞﾋﾟﾝ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ2",
"WorkItems": [
"◆1. SPRING(BLACK) 端部の輪を引っ掛け､ﾘﾝｸﾞ状にする",
"◆2. CLAMP-ARM(BLACK) 先端部の溝部へｸﾞﾘｰｽを塗布する",
"◆3. 2完成品を㉚治具にセットし、グリスを塗布する",
"4. ㉛治具に③を8個セットする",
"◆5. 4完成品の指定箇所にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"SPRING(BLACK) 端部の輪を引っ掛ける",
"保護ﾒｶﾞﾈ着用",
"この作業では同じものを8個製作",
"この作業では同じものを16個製作",
"この作業では同じものを8個製作",
"この作業では同じものを16個製作",
"写真の様に設置する",
"溝部以外の余分なｸﾞﾘｰｽは拭取る"
],
"Tolks": [],
"InspectionNo": "GWETJ-F013-001",
"InspectionItems": [
"検査表SPRING(BLACK) :ｸﾗﾝﾌﾟｱｰﾑ ｸﾞﾘｰｽ塗布",
"検査表SPRING(BLACK) :ｸﾗﾝﾌﾟｱｰﾑ ｸﾞﾘｰｽ塗布"
],
"WorkTypes": [],
"Words": [
"溝部に確実に入るようにｸﾞﾘｰｽを塗布すること",
"溝部",
"㉚ FM-5845",
"㉛ FM-5765",
"ｸﾞﾘｰｽ塗布位置",
"ｸﾞﾘｰｽ塗布位置 (反対側にもあり)",
"ｸﾞﾘｰｽ塗布位置",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(1個につき)",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(1個につき)",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:2(1個につき2箇所)",
"ﾋﾝｼﾞﾋﾟﾝ",
"GWETJ-F013-001"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1ｺﾞﾏ粒:各2",
"Method": "目視",
"RecordMethod": "GWETJ-F013-001",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽFM-5845",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ2",
"WorkItems": [
"◆1. SPRING(BLACK) 端部の輪を引っ掛け､ﾘﾝｸﾞ状にする",
"◆2. CLAMP-ARM(BLACK) 先端部の溝部へｸﾞﾘｰｽを塗布する",
"◆3. 2完成品を㉚治具にセットし、グリスを塗布する"
],
"WorkPoints": [
"SPRING(BLACK) 端部の輪を引っ掛ける",
"保護ﾒｶﾞﾈ着用",
"この作業では同じものを8個製作",
"この作業では同じものを16個製作",
"溝部以外の余分なｸﾞﾘｰｽは拭取る"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(1個につき)",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞ組立治具",
"Size": "",
"ToolOther": "FM-5765",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ2",
"WorkItems": [
"4. ㉛治具に③を8個セットする",
"◆5. 4完成品の指定箇所にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"この作業では同じものを16個製作",
"写真の様に設置する",
"この作業では同じものを8個製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"溝部に確実に入るようにｸﾞﾘｰｽを塗布すること",
"㉚ FM-5845",
"㉛ FM-5765",
"ｸﾞﾘｰｽ塗布位置",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(1個につき)",
"ﾋﾝｼﾞﾋﾟﾝ",
"◆作業者安全作業",
"ｸﾞﾘｰｽ塗布位置 (反対側にもあり)",
"検査表SPRING(BLACK) :ｸﾗﾝﾌﾟｱｰﾑ ｸﾞﾘｰｽ塗布",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:2(1個につき2箇所)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5765",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞ組立治具",
"Size": "固定用",
"ToolOther": "FM-5765",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ3",
"WorkItems": [
"1. ①（㉖治具）の隙間を調整する",
"3. 2完成品に治具㉘を取付後、治具㉘先端から③を取付",
"2. 1完成品に②を挿入し､治具をﾛｯｸする"
],
"WorkPoints": [
"※㉗スケール厚み0.5mmにて隙間を設けています",
"隙間0.5mm程度",
"隙間0.5mm程度",
"治具㉘をｾｯﾄする",
"③ｽﾌﾟﾘﾝｸﾞの連結部が左側になるよう挿入する",
"この作業では同じものを8個製作",
"②ｱｰﾑが歪み無く取付られ､ｽﾑｰｽﾞに動くことを確認する",
"連結部の向きとﾋﾝｼﾞﾋﾟﾝの位置が同じ側にある事",
"ﾛｯｸ:ｽｹｰﾙを外し､ﾉﾌﾞを回し締結する",
"この作業では同じものを8個製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉖ FM-5765",
"㉘ FM-5765",
"ﾋﾝｼﾞﾋﾟﾝ",
"連結部"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5765",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ3",
"WorkItems": [
"1. ①（㉖治具）の隙間を調整する"
],
"WorkPoints": [
"※㉗スケール厚み0.5mmにて隙間を設けています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉖ FM-5765"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞ組立治具",
"Size": "固定用",
"ToolOther": "FM-5765",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ3",
"WorkItems": [
"1. ①（㉖治具）の隙間を調整する",
"3. 2完成品に治具㉘を取付後、治具㉘先端から③を取付",
"2. 1完成品に②を挿入し､治具をﾛｯｸする"
],
"WorkPoints": [
"※㉗スケール厚み0.5mmにて隙間を設けています",
"隙間0.5mm程度",
"隙間0.5mm程度",
"治具㉘をｾｯﾄする",
"③ｽﾌﾟﾘﾝｸﾞの連結部が左側になるよう挿入する",
"この作業では同じものを8個製作",
"②ｱｰﾑが歪み無く取付られ､ｽﾑｰｽﾞに動くことを確認する",
"連結部の向きとﾋﾝｼﾞﾋﾟﾝの位置が同じ側にある事",
"ﾛｯｸ:ｽｹｰﾙを外し､ﾉﾌﾞを回し締結する",
"この作業では同じものを8個製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉖ FM-5765",
"㉘ FM-5765",
"ﾋﾝｼﾞﾋﾟﾝ",
"連結部"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5765",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "4㎜幅",
"ToolOther": "10cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ4",
"WorkItems": [
"1. ①にFILTER を取付",
"2. ㉘治具からノズルホルダ―を取り外す",
"3. 2完成品にSPRING を組付け"
],
"WorkPoints": [
"ばね先端を広げ過ぎない様に注意して､①の溝部分に確実に挿入",
"8個全て取り外す",
"【注意】 歯幅4mmのﾏｲﾅｽﾄﾞﾗｲﾊﾞｰを使用して下さい"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉘ FM-5765",
"この作業では同じものを8個製作",
"ばねの先端を微妙に押し広げながらCCW(半時計方向)に回すと容易に挿入出来る｡",
"ばね溝(緑線)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞ組立治具",
"Size": "",
"ToolOther": "FM-5765",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞ4",
"WorkItems": [
"1. ①にFILTER を取付",
"2. ㉘治具からノズルホルダ―を取り外す",
"3. 2完成品にSPRING を組付け"
],
"WorkPoints": [
"ばね先端を広げ過ぎない様に注意して､①の溝部分に確実に挿入",
"8個全て取り外す",
"【注意】 歯幅4mmのﾏｲﾅｽﾄﾞﾗｲﾊﾞｰを使用して下さい"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉘ FM-5765",
"この作業では同じものを8個製作",
"ばねの先端を微妙に押し広げながらCCW(半時計方向)に回すと容易に挿入出来る｡",
"ばね溝(緑線)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5765",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾗｲﾝｼｬﾌﾄｸﾘｰﾆﾝｸﾞ",
"WorkItems": [
"2. ｼｬﾌﾄ部をｱﾙｺｰﾙ･ｳｴｽで防錆油を拭き取った後､ｽﾌﾟﾗｲﾝ外筒を数回上下させ封入ｸﾞﾘｰｽをｼｬﾌﾄに馴染ませる",
"1. BALL-SPLINE のｼﾘｱﾙﾅﾝﾊﾞｰを確認"
],
"WorkPoints": [
"この作業では同じものを8個製作",
"A部(青枠部分)を脱脂し､以降の工程で素手で触れないこと(触れた場合は必ず脱脂する事)",
"外筒のｼﾘｱﾙﾅﾝﾊﾞｰと､ｼｬﾌﾄのｼﾘｱﾙﾅﾝﾊﾞｰが合致しているか確認",
"ｽﾌﾟﾗｲﾝ外筒をｼｬﾌﾄから取り外し､ｼﾘｱﾙNo.順に並べておく",
"ｼｬﾌﾄ部全体の防錆油を拭き取る"
],
"Tolks": [],
"InspectionNo": "GWETJ-F013-001",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｽﾌﾟﾗｲﾝ外筒側ｼﾘｱﾙﾅﾝﾊﾞｰ",
"検査表BALL-SPLINE :ﾎﾞｰﾙｽﾌﾟﾗｲﾝｼﾘｱﾙ№記録",
"ｽﾌﾟﾗｲﾝｼｬﾌﾄｼﾘｱﾙﾅﾝﾊﾞｰ",
"GWETJ-F013-001"
]
} | {
"QualityItem": "ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "GWETJ-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｳｼﾞﾝｸﾞ組立(ﾎﾞｰﾙ圧入)",
"WorkItems": [
"◆1. HOUSING の内部ﾊﾞﾘ確認",
"2. 1完成品にSTEEL-BALL を圧入"
],
"WorkPoints": [
"この作業では同じものを8個製作",
"保護ﾒｶﾞﾈ着用",
"ﾎﾙﾀﾞｰ内部を確認し､ﾊﾞﾘ･異物があれば取除く",
"除去の際は切削面や内壁を傷付けないようにする事",
"貫通穴交差部分は特に注意して下さい",
"【注意】 HOUSING ﾊｳｼﾞﾝｸﾞの略図青色部分は精密仕上げ面の為､取り扱いにご注意下さい ※略図参照",
"略図の様に㉙治具に設置して圧入して下さい",
"上面(青線)基準で圧入して下さい"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉙ FM-5713"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、異物等が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾞｰﾙ圧入受け治具",
"Size": "",
"ToolOther": "FM-5713",
"WorkName": "ﾊｳｼﾞﾝｸﾞ組立(ﾎﾞｰﾙ圧入)",
"WorkItems": [
"◆1. HOUSING の内部ﾊﾞﾘ確認",
"2. 1完成品にSTEEL-BALL を圧入"
],
"WorkPoints": [
"この作業では同じものを8個製作",
"ﾎﾙﾀﾞｰ内部を確認し､ﾊﾞﾘ･異物があれば取除く",
"除去の際は切削面や内壁を傷付けないようにする事",
"貫通穴交差部分は特に注意して下さい",
"【注意】 HOUSING ﾊｳｼﾞﾝｸﾞの略図青色部分は精密仕上げ面の為､取り扱いにご注意下さい ※略図参照",
"略図の様に㉙治具に設置して圧入して下さい"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5713",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｳｼﾞﾝｸﾞ圧入治具",
"Size": "",
"ToolOther": "FM-5725",
"WorkName": "ﾊｳｼﾞﾝｸﾞ組立(ﾍﾞｱﾘﾝｸﾞ圧入)",
"WorkItems": [
"1. BEARING にPIN を圧入",
"2. 1完成品に④を圧入",
"1. BEARING にPIN を圧入",
"2. 1完成品に④を圧入",
"3. 2完成品にJOINT を取付"
],
"WorkPoints": [
"④のﾍﾞｱﾘﾝｸﾞ圧入側を下にして挿入",
"治具㉖-Ⅲを置いて④圧入",
"治具㉖ベースにBEARING をｾｯﾄする",
"治具㉖-Ⅰを治具㉖-Ⅱに入れ換え④を挿入",
"治具㉖ベースにBEARING を置いてから治具㉖-Ⅰを被せる、治具の穴にPIN を挿入後、圧入",
"④のﾍﾞｱﾘﾝｸﾞ圧入側を下にして挿入",
"治具㉖-Ⅲを置いて④圧入",
"治具㉖ベースにBEARING をｾｯﾄする",
"治具㉖-Ⅰを治具㉖-Ⅱに入れ換え④を挿入",
"治具㉖ベースにBEARING を置いてから治具㉖-Ⅰを被せる、治具の穴にPIN を挿入後、圧入",
"治具㉖-Ⅱの上に治具㉖-Ⅳを置き、JOINT を取付"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを8個製作",
"治具:FM-5725ﾍﾞｰｽ",
"この作業では同じものを8個製作",
"治具:FM-5725ﾍﾞｰｽ",
"治具:FM-5725-Ⅳ",
"治具:FM-5725-Ⅱ",
"治具:FM-5725-Ⅱ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5725",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜BOX",
"ToolOther": "40cN･m",
"WorkName": "ﾊｳｼﾞﾝｸﾞ組立(ﾍﾞｱﾘﾝｸﾞ圧入)",
"WorkItems": [
"3. 2完成品にJOINT を取付"
],
"WorkPoints": [
"治具㉖-Ⅱの上に治具㉖-Ⅳを置き、JOINT を取付"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"治具:FM-5725-Ⅳ",
"治具:FM-5725-Ⅱ",
"治具:FM-5725-Ⅱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Yﾊﾟｯｷﾝｽﾀﾝﾄﾞｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6126",
"WorkName": "ﾊｳｼﾞﾝｸﾞ組立(ﾊﾟｯｷﾝ準備)",
"WorkItems": [
"1. ㉗工具を清掃する",
"◆2. ㉗工具に㉘グリスを塗布する",
"◆3. ㉗工具にPACKING を16個挿入し、PACKING の内周にグリスをなじませる",
"◆4. 3完成品の外周に㉘グリスを塗布する"
],
"WorkPoints": [
"PACKING の外周にｸﾞﾘｰｽを線状に塗布し､指で回転させ 外周全体にｸﾞﾘｰｽを塗り広げる",
"【確認】 ｼｬﾌﾄ部分に傷がな事を確認して使用する",
"この作業では同じものを16個製作",
"PACKING の溝にはｸﾞﾘｰｽが入らない様にする事"
],
"Tolks": [],
"InspectionNo": "GWETJ-F013-001",
"InspectionItems": [
"検査表PACKING :Yﾊﾟｯｷﾝの組立"
],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"外周全体に塗り広げる",
"注射器",
"*16mm程度",
"ｸﾞﾘｰｽの偏りを防ぐため（㉗工具に挿入した状態で）PACKING を指2本で押しつぶしながら90°ずつ持ち位置を替えて3～4回、回転させる（持ち位置を替えずに押しつぶしながら回転させるのはNG）",
"PACKING +工具㉗",
"ｸﾞﾘｰｽをなじませる",
"ｸﾞﾘｰｽをなじませる",
"GWETJ-F013-001"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6126",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "GWETJ-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.