ayuzawa/ManageProcess20 · Datasets at Hugging Face

instruction stringlengths 222 3.65k	output stringlengths 193 367	category stringclasses 1 value	fileName null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ摺動確認", "WorkItems": [ "1. ﾉｽﾞﾙﾎﾙﾀﾞ摺動確認" ], "WorkPoints": [ "【確認方法】 ※全ﾉｽﾞﾙ実施手順1 ﾉｽﾞﾙﾎﾙﾀﾞｰ先端を指で押し(黄色矢印)､ﾊﾞﾈにて摺動する事を確認手順2 ﾉｽﾞﾙﾎﾙﾀﾞｰを180°回転させて再取付手順3 再度､ﾉｽﾞﾙﾎﾙﾀﾞｰ先端を指で押し､ﾊﾞﾈにて摺動する事を確認" ], "Tolks": [], "InspectionNo": "GWETJ-F013-001", "InspectionItems": [ "検査表①:ﾉｽﾞﾙﾎﾙﾀﾞ摺動確認" ], "WorkTypes": [], "Words": [ "GWETJ-F013-001" ] }	{ "QualityItem": "摺動確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "滑らかに動く事", "Method": "目視/手感", "RecordMethod": "GWETJ-F013-001", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "100cN･m", "WorkName": "θ原点ﾄﾞｸﾞｶﾊﾞｰ取付", "WorkItems": [ "1. ①にCOVER COVER をBOLT にて取付" ], "WorkPoints": [ "【確認】原点ﾄﾞｸﾞにｸﾞﾘｰｽが塗られている事" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "ﾉｽﾞﾙｶﾞｰﾄﾞ取付", "WorkItems": [ "1. ①にCOVER をBOLT WASHER で取付" ], "WorkPoints": [ "【取付ﾎﾟｲﾝﾄ】黄色矢印方向に押し付けながら締結 ※左右の高さを揃えるため" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "1.5㎜", "ToolOther": "50cN･m", "WorkName": "整定板ｶﾊﾞｰ取付", "WorkItems": [ "1. ①にCOVER をBOLT WASHER で取付", "2. 取付確認" ], "WorkPoints": [ "【注意】 COVER 取付後､ｽﾌﾟﾗｲﾝを摺動させて干渉無き事", "COVER 取付後､全ﾉｽﾞﾙﾍﾞｱﾘﾝｸﾞ(黄色部分)がｶﾊﾞｰ(黒色部分)と干渉してい無い事", "ﾉｽﾞﾙを手で摺動させ確認" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾉｽﾞﾙﾍﾞｱﾘﾝｸﾞ(黄)", "ｶﾊﾞｰ(黒)", "制定ﾌﾟﾚｰﾄ(青)" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "50cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾁｭｰﾌﾞ取付", "WorkItems": [ "◆1. TUBE (70MM CUT) をｴｱｰｶﾞﾝにて､清掃する", "2. ①にTUBE (70MM CUT) を取付" ], "WorkPoints": [ "ﾁｭｰﾌﾞ取付け後､ｽﾌﾟﾗｲﾝｼｬﾌﾄが上昇端まで上がることを確認", "TUBE (70MM CUT) は8本取付", "【注意】保護ﾒｶﾞﾈ着用の事", "【取付注意】ﾁｭｰﾌﾞは継手根本まで差込む事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｺﾞﾐ､埃が無い事", "Method": "目視", "RecordMethod": "-", "Other": "保護ﾒｶﾞﾈ", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "60cN･m", "WorkName": "ﾀｲﾏｳﾝﾄ取付", "WorkItems": [ "1. ①にCABLE-SUPPORT BOLT CABLE-SUPPORT BOLT を取付" ], "WorkPoints": [ "【取付目安】 CABLE-SUPPORT は約45度傾けて取付 ※略図参照" ], "Tolks": [ "BOLT 締付ﾄﾙｸ 100cN･m ﾎﾞﾀﾝﾎﾞﾙﾄ", "BOLT 締付ﾄﾙｸ 60cN･m 皿ﾎﾞﾙﾄ" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "正面", "背面", "左側面", "右側面" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "ﾀｲﾏｳﾝﾄ取付", "WorkItems": [ "1. ①にCABLE-SUPPORT BOLT CABLE-SUPPORT BOLT を取付" ], "WorkPoints": [ "【取付目安】 CABLE-SUPPORT は約45度傾けて取付 ※略図参照" ], "Tolks": [ "BOLT 締付ﾄﾙｸ 100cN･m ﾎﾞﾀﾝﾎﾞﾙﾄ", "BOLT 締付ﾄﾙｸ 60cN･m 皿ﾎﾞﾙﾄ" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "正面", "背面", "左側面", "右側面" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP1~NP4ﾌﾛｰｾﾝｻｰ接続/結束1", "WorkItems": [ "2. ﾌﾞﾗｹｯﾄに結束", "1. ①のﾌﾛｰｾﾝｻｰにCABLE ｺﾈｸﾀｰを接続" ], "WorkPoints": [ "【注意】ｲﾝｼｭﾛｯｸの頭の向きは下側", "【注意】ｲﾝｼｭﾛｯｸの頭の向きは外側", "詳細は検査表参照", "一部を省いて描いています", "ｺﾈｸﾀｰﾗﾍﾞﾙを確認後､接続" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾌﾛｰｾﾝｻ接続確認(NP1~NP4)" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "F1", "F2", "F3", "F4", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP1~NP4ﾌﾛｰｾﾝｻｰ接続/結束2", "WorkItems": [ "1. ﾌﾛｰｾﾝｻｰ線とθ2軸原点ｾﾝｻｰ線を仮結束" ], "WorkPoints": [ "一部を省いて描いています", "仮結束です", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP1~NP4真空(V)/ﾌﾞﾛｰ(B)ﾊﾞﾙﾌﾞ接続確認1", "WorkItems": [ "1. ①のﾊﾞﾙﾌﾞ(NP1~NP4 真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ)にCABLE を接続" ], "WorkPoints": [ "詳細は検査表参照", "一部を省いて描いています", "ｺﾈｸﾀｰﾗﾍﾞﾙを確認後､接続" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ接続確認(NP1~NP4)" ], "WorkTypes": [], "Words": [ "NP1V1", "NP1B1", "NP2V2", "NP2B2", "NP3V3", "NP3B3", "NP4V4", "NP4B4", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP1~NP4真空(V)/ﾌﾞﾛｰ(B)ﾊﾞﾙﾌﾞ接続確認2", "WorkItems": [ "1. NP1~NP4 真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ線をﾀｲﾏｳﾝﾄに仮結束", "2. 配線のみを結束" ], "WorkPoints": [ "仮結束です", "3本のみ略図の位置に結束です", "B3､V4､B4線を結束 ※略図参照", "一部を省いて描いています", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "B3", "V4", "B4" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1原点ｾﾝｻｰ線引き回", "WorkItems": [ "1. ①のθ1原点ｾﾝｻｰ線を仮結束" ], "WorkPoints": [ "一部を省いて描いています", "仮結束です" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP5~NP8ﾌﾛｰｾﾝｻｰ接続/結束1", "WorkItems": [ "1. ①のﾌﾛｰｾﾝｻｰにCABLE ｺﾈｸﾀｰを接続", "2. ﾌﾞﾗｹｯﾄに結束" ], "WorkPoints": [ "【注意】ｲﾝｼｭﾛｯｸの頭の向きは下側", "【注意】ｲﾝｼｭﾛｯｸの頭の向きは外側", "詳細は検査表参照", "一部を省いて描いています", "ｺﾈｸﾀｰﾗﾍﾞﾙを確認後､接続" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾌﾛｰｾﾝｻ接続確認(NP5~NP8)" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "F8", "F7", "F6", "F5", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP5~NP8ﾌﾛｰｾﾝｻｰ接続/結束2", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP5~NP8真空(V)/ﾌﾞﾛｰ(B)ﾊﾞﾙﾌﾞ接続確認1", "WorkItems": [ "1. ①のﾊﾞﾙﾌﾞ(NP5~NP8 真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ)にCABLE を接続" ], "WorkPoints": [ "詳細は検査表参照", "一部を省いて描いています", "ｺﾈｸﾀｰﾗﾍﾞﾙを確認後､接続" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ接続確認(NP5~NP8)" ], "WorkTypes": [], "Words": [ "NP8V8", "NP8B8", "NP7V7", "NP7B7", "NP6V6", "NP6B6", "NP5V5", "NP5B5", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP5~NP8真空(V)/ﾌﾞﾛｰ(B)ﾊﾞﾙﾌﾞ接続確認2", "WorkItems": [ "2. 配線を結束", "1. NP5~NP8 真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ線をﾀｲﾏｳﾝﾄに仮結束" ], "WorkPoints": [ "一部を省いて描いています", "仮結束です", "3本のみ略図の位置に結束です", "B5､B6､V6線を結束 ※略図参照", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "B6", "V5", "B5" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ固定ｼﾞｸ", "Size": "", "ToolOther": "FM-5717", "WorkName": "θ軸ﾕﾆｯﾄ取付", "WorkItems": [ "4. ②取付後、㉖治具を静かに取り外す", "1. ②に㉖治具を取付", "◆2. ﾗﾐﾀﾓｰﾀｰ先端ﾌﾞﾛｯｸにｸﾞﾘｰｽ塗布", "3. ①に2完成品をBOLT BOLT WASHER にて取付" ], "WorkPoints": [ "【注意】　配線の嚙み込みや干渉が無い事", "【注意】ﾎﾞﾙﾄ長さが異なる ※略図参照", "①のﾋﾟﾝに嵌合させて取付", "ノズルシャフトを手で押し下げて、制定プレートとノズルブロックの間に㉖治具を設置する", "治具㉖は黄色で表示しています", "一部を省いて描いています", "略図青色部分にｸﾞﾘｰｽ塗布" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布米粒:8" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "FM-5717", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ軸ﾕﾆｯﾄ取付", "WorkItems": [ "4. ②取付後、㉖治具を静かに取り外す", "1. ②に㉖治具を取付", "◆2. ﾗﾐﾀﾓｰﾀｰ先端ﾌﾞﾛｯｸにｸﾞﾘｰｽ塗布", "3. ①に2完成品をBOLT BOLT WASHER にて取付" ], "WorkPoints": [ "【注意】　配線の嚙み込みや干渉が無い事", "【注意】ﾎﾞﾙﾄ長さが異なる ※略図参照", "①のﾋﾟﾝに嵌合させて取付", "ノズルシャフトを手で押し下げて、制定プレートとノズルブロックの間に㉖治具を設置する", "治具㉖は黄色で表示しています", "一部を省いて描いています", "略図青色部分にｸﾞﾘｰｽ塗布" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布米粒:8" ] }	{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "米粒:8", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "θ軸ﾕﾆｯﾄ取付", "WorkItems": [ "4. ②取付後、㉖治具を静かに取り外す", "3. ①に2完成品をBOLT BOLT WASHER にて取付" ], "WorkPoints": [ "【注意】　配線の嚙み込みや干渉が無い事", "【注意】ﾎﾞﾙﾄ長さが異なる ※略図参照", "①のﾋﾟﾝに嵌合させて取付" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "◆作業者安全作業" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱﾓｰﾀｰ連結部品取付", "WorkItems": [ "◆1. BRACKET の指定箇所にｸﾞﾘｰｽを塗布する", "2. ①に1完成品をBOLT にて取付", "3. Z軸摺動確認 (全8軸)" ], "WorkPoints": [ "【BRACKET の傾きを押さえる締付方法】BOLT のﾎﾞﾙﾄにﾚﾝﾁを挿入し､青矢印方向にﾉｽﾞﾙﾎﾙﾀﾞｰ(ｽﾌﾟﾗｲﾝｼｬﾌﾄ)を引っ張った状態でBOLT を締結", "一部を省いて描いています", "【注意】締結時､ﾄﾙｸﾄﾞﾗｲﾊﾞｰを押し過ぎて､ﾘﾆｱﾓｰﾀｼｬﾌﾄに過大な力をかけ無い事", "【注意】ﾊﾞﾈを圧縮した状態から放すと､勢いよく上昇し衝撃で破損します", "【確認方法】ﾉｽﾞﾙﾎﾙﾀﾞｰを1mm程指で引っ張り､静かに放しﾊﾞﾈで上端まで戻る事を確認する", "【注意】 BRACKET は位置決めﾋﾟﾝに確実に嵌合されている事", "【注意】 BRACKET の先端部分が隙間に挿入されている事" ], "Tolks": [ "締付ﾄﾙｸ 30cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "位置決めﾋﾟﾝ", "隙間に挿入させる", "ｸﾞﾘｰｽ塗布位置", "ｸﾞﾘｰｽ塗布ｺﾞﾏ粒:1 計ｺﾞﾏ粒:8", "確実に嵌合させる", "検査表①:Z軸上昇確認" ] }	{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｺﾞﾏ粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "1.5㎜", "ToolOther": "30cN･m", "WorkName": "ﾘﾆｱﾓｰﾀｰ連結部品取付", "WorkItems": [ "◆1. BRACKET の指定箇所にｸﾞﾘｰｽを塗布する", "2. ①に1完成品をBOLT にて取付" ], "WorkPoints": [ "【BRACKET の傾きを押さえる締付方法】BOLT のﾎﾞﾙﾄにﾚﾝﾁを挿入し､青矢印方向にﾉｽﾞﾙﾎﾙﾀﾞｰ(ｽﾌﾟﾗｲﾝｼｬﾌﾄ)を引っ張った状態でBOLT を締結", "一部を省いて描いています", "【注意】締結時､ﾄﾙｸﾄﾞﾗｲﾊﾞｰを押し過ぎて､ﾘﾆｱﾓｰﾀｼｬﾌﾄに過大な力をかけ無い事", "【注意】 BRACKET は位置決めﾋﾟﾝに確実に嵌合されている事", "【注意】 BRACKET の先端部分が隙間に挿入されている事" ], "Tolks": [ "締付ﾄﾙｸ 30cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布位置", "ｸﾞﾘｰｽ塗布ｺﾞﾏ粒:1 計ｺﾞﾏ粒:8", "◆作業者安全作業" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "30cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱﾓｰﾀｰ連結部品取付", "WorkItems": [ "◆1. BRACKET の指定箇所にｸﾞﾘｰｽを塗布する", "2. ①に1完成品をBOLT にて取付", "3. Z軸摺動確認 (全8軸)" ], "WorkPoints": [ "【BRACKET の傾きを押さえる締付方法】BOLT のﾎﾞﾙﾄにﾚﾝﾁを挿入し､青矢印方向にﾉｽﾞﾙﾎﾙﾀﾞｰ(ｽﾌﾟﾗｲﾝｼｬﾌﾄ)を引っ張った状態でBOLT を締結", "一部を省いて描いています", "【注意】締結時､ﾄﾙｸﾄﾞﾗｲﾊﾞｰを押し過ぎて､ﾘﾆｱﾓｰﾀｼｬﾌﾄに過大な力をかけ無い事", "【注意】ﾊﾞﾈを圧縮した状態から放すと､勢いよく上昇し衝撃で破損します", "【確認方法】ﾉｽﾞﾙﾎﾙﾀﾞｰを1mm程指で引っ張り､静かに放しﾊﾞﾈで上端まで戻る事を確認する", "【注意】 BRACKET は位置決めﾋﾟﾝに確実に嵌合されている事", "【注意】 BRACKET の先端部分が隙間に挿入されている事" ], "Tolks": [ "締付ﾄﾙｸ 30cN･m" ], "InspectionNo": "GWETJ-F013-001", "InspectionItems": [ "検査表①:Z軸上昇確認" ], "WorkTypes": [], "Words": [ "位置決めﾋﾟﾝ", "隙間に挿入させる", "ｸﾞﾘｰｽ塗布位置", "ｸﾞﾘｰｽ塗布ｺﾞﾏ粒:1 計ｺﾞﾏ粒:8", "確実に嵌合させる", "GWETJ-F013-001" ] }	{ "QualityItem": "摺動確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "上端ﾒｶｽﾄまで上がること(8軸)", "Method": "目視", "RecordMethod": "GWETJ-F013-001", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付1", "WorkItems": [ "1. ①に②③をBOLT WASHER にて取付" ], "WorkPoints": [ "一部を省いて描いています", "全てのﾎﾞﾙﾄを取付後､均一に締結する", "【取付目安】 115mmを目安に取付 ※略図参照" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付1", "WorkItems": [ "1. ①に②③をBOLT WASHER にて取付" ], "WorkPoints": [ "一部を省いて描いています", "全てのﾎﾞﾙﾄを取付後､均一に締結する", "【取付目安】 115mmを目安に取付 ※略図参照" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付2", "WorkItems": [ "1. ①にCOVER をSPACER BOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付2", "WorkItems": [ "1. ①にCOVER をSPACER BOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付2", "WorkItems": [ "1. ①にCOVER をSPACER BOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)接続", "WorkItems": [ "■★1. FC08 IO BOARD I/Oﾎﾞｰﾄﾞ1(K302)の型式･検査書確認", "★2. I/Oﾎﾞｰﾄﾞ(K302) (CN3､CN4､CN10)を接続" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認" ], "WorkTypes": [], "Words": [ "K302I/Oﾎﾞｰﾄﾞ1", "検査表①:型式･検査書確認", "GWETJ-F013-002" ] }	{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙ番号転記", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)接続", "WorkItems": [ "■★1. FC08 IO BOARD I/Oﾎﾞｰﾄﾞ1(K302)の型式･検査書確認", "★2. I/Oﾎﾞｰﾄﾞ(K302) (CN3､CN4､CN10)を接続" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:型式･検査書確認" ], "WorkTypes": [], "Words": [ "K302I/Oﾎﾞｰﾄﾞ1", "検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "5㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)取付", "WorkItems": [ "■1. I/Oﾎﾞｰﾄﾞ1(K302)をBOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "CN3、CN4、CN10を本結束", "WorkItems": [ "1. 仮結束のｲﾝｼｭﾛｯｸを本結束する" ], "WorkPoints": [ "配線を微調整して､仮結束のｲﾝｼｭﾛｯｸを本結束して下さい", "【確認】心線が可動部やｴｯｼﾞ部に干渉していないか確認" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾒｲﾝﾎﾞｰﾄﾞ(K301)取付", "WorkItems": [ "■★1. FC08 MAIN BOARD ﾒｲﾝﾎﾞｰﾄﾞの型式･検査書確認", "■★2. FC08 MAIN BOARD ﾒｲﾝﾎﾞｰﾄﾞをBOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 80cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:型式･検査書確認" ], "WorkTypes": [], "Words": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認", "GWETJ-F013-002" ] }	{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙ番号転記", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "80cN･m", "WorkName": "ﾒｲﾝﾎﾞｰﾄﾞ(K301)取付", "WorkItems": [ "■★1. FC08 MAIN BOARD ﾒｲﾝﾎﾞｰﾄﾞの型式･検査書確認", "■★2. FC08 MAIN BOARD ﾒｲﾝﾎﾞｰﾄﾞをBOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 80cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "検査表①:型式･検査書確認", "■安全作業", "★静電対策作業" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "80cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)接続", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [], "WorkTypes": [], "Words": [ "GWETJ-F013-002" ] }	{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙ番号転記", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)接続", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [], "WorkTypes": [], "Words": [ "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)取付", "WorkItems": [ "■1. I/Oﾎﾞｰﾄﾞ2(K303)を本締め" ], "WorkPoints": [ "一部を省いて描いています", "【注意】ｺﾈｸﾀｰの接続に配慮して無理な力は極力避けて作業する", "【注意】基板取付後､ｺﾈｸﾀｰの接続が確実か確認する", "【重要】ｺﾈｸﾀｰ心線が上空方向に膨らむと､後工程にてｶﾊﾞｰと干渉する恐れあり", "SD-A036545-007の本締め" ], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)中継配線接続", "WorkItems": [ "1. I/Oﾎﾞｰﾄﾞ2(K303)中継線接続" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認" ], "WorkTypes": [], "Words": [ "検査表①:IOﾎﾞｰﾄﾞ2(K303)接続確認", "CN1K303", "CN2K302", "正面", "背面", "左側面", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ2結束", "WorkItems": [ "1. I/Oﾎﾞｰﾄﾞ2(303)中継配線を結束(1箇所のみ)", "2. I/Oﾎﾞｰﾄﾞ2(K303)の仮結束部分を結束する (3箇所)" ], "WorkPoints": [ "【注意】 1箇所のみ結束", "【結束目安】ｺﾈｸﾀｰにｽﾄﾚｽの少ない位置で結束", "配線を微調整して､仮結束のｲﾝｼｭﾛｯｸを本結束して下さい", "【確認】心線が可動部やｴｯｼﾞ部に干渉していないか確認" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.1", "ToolOther": "50cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)基板ｶﾊﾞｰ取付", "WorkItems": [ "■1. ①にCOVER をSCREW にて取付" ], "WorkPoints": [ "一部を省いて描いています", "【重要】ｶﾊﾞｰ取付後に各心線やｺﾈｸﾀｰが､ｶﾊﾞｰと干渉していないか確認する" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "50cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "ｴｱﾁｭｰﾌﾞｶｯﾄ", "WorkItems": [ "1. ｴｱﾁｭｰﾌﾞを指定寸法にｶｯﾄ" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｱﾁｭｰﾌﾞ接続", "WorkItems": [ "1. ｴｱﾁｭｰﾌﾞを接続" ], "WorkPoints": [ "一部を省いて描いています", "【注意】ｴｱﾁｭｰﾌﾞは確実に接続する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "③黄色 265mm", "②黄色 270mm", "⑤白色 210mm", "④白色 235mm", "④白色 235mm", "⑤白色 210mm" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｱﾁｭｰﾌﾞ接続・結束1", "WorkItems": [ "1. 略図の様にｴｱﾁｭｰﾌﾞを接続", "2. 略図の順序で結束する" ], "WorkPoints": [ "ｴｱﾁｭｰﾌﾞは確実に接続する事", "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ｴｱﾁｭｰﾌﾞのみ結束(ﾗﾌ原点ｾﾝｻｰ線は結束しない)", "【結束手順 2】ｴｱﾁｭｰﾌﾞどうしを結束", "【結束手順 3】ﾌﾞﾗｹｯﾄに結束", "【結束手順 4】ｴｱﾁｭｰﾌﾞどうしを結束", "【結束手順 5】ﾀｲﾏｳﾝﾄに結束" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1原点ｾﾝｻｰ線結束", "WorkItems": [ "1. 仮結束の部分を結束", "2. θ軸原点ｾﾝｻｰ線を結束" ], "WorkPoints": [ "ｴｱﾁｭｰﾌﾞに結束する", "【確認】結束後､過度な干渉が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｱﾁｭｰﾌﾞ接続・結束2", "WorkItems": [ "1. 略図の様にｴｱﾁｭｰﾌﾞを接続", "2. 略図の順序で結束する" ], "WorkPoints": [ "一部を省いて描いています", "ｴｱﾁｭｰﾌﾞは確実に接続する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ｴｱﾁｭｰﾌﾞと配線を結束", "【結束手順 4】ﾌﾞﾗｹｯﾄにｴｱﾁｭｰﾌﾞと配線を結束", "【結束手順 3】ｴｱﾁｭｰﾌﾞと配線を結束", "【結束手順 2】配線をﾀｲﾏｳﾝﾄに結束※2ｶ所", "【結束手順 5】ﾀｲﾏｳﾝﾄに結束", "【結束手順 6】ｴｱﾁｭｰﾌﾞどうしを結束" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "配管取付確認", "WorkItems": [ "1. 配管取付確認" ], "WorkPoints": [ "略図の様に㉖スケールをセットし、配管が干渉していないか確認" ], "Tolks": [], "InspectionNo": "GWETJ-F013-001", "InspectionItems": [ "検査表①:配管取付け確認" ], "WorkTypes": [], "Words": [ "㉖スケール" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "BRACKETより飛出してい無い事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "中継線結束", "WorkItems": [ "1. 中継線をﾎﾟｽﾄに結束" ], "WorkPoints": [ "【注意】ﾍｯﾄﾞ内部にあるｽﾌﾟﾘﾝｸﾞとの干渉防止の為､心線が上に向く様に結束", "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "【注意】ﾍｯﾄﾞ内部にあるｽﾌﾟﾘﾝｸﾞとの干渉防止の為､略図の様なたすき掛けにして下さい【確認】施工後､ｽﾌﾟﾘﾝｸﾞと干渉が無い事を確認して下さい", "ｶﾊﾞｰﾎﾟｽﾄに配線を結束", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ2側ﾒｲﾝﾎﾞｰﾄﾞ接続", "WorkItems": [ "1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN7を接続", "2. ﾓｰﾀｰ線の被覆を下略図の様に施工する", "3. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN2を接続", "4. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN3を接続" ], "WorkPoints": [ "【注意】下記の手順にて接続して下さい", "略図にて配線の重なる順序を確認して作業して下さい" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認", "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認", "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "CN3K301ﾀｸﾞはまだ付いていませんθ軸ﾓｰﾀｰの信号線です", "CN2K301ﾀｸﾞはまだ付いていません", "CN7", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ2側基板結束", "WorkItems": [ "1. 略図の順序で結束する" ], "WorkPoints": [ "一部を省いて描いています", "【注意】断線防止の為､配線を引っ張った状態で結束し無い事", "【注意】基板と配線の干渉が無い事", "【注意】配線とFANとの干渉が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾌﾞﾗｹｯﾄ上側にﾘﾆｱﾓｰﾀｰ線下側にθ2ﾓｰﾀｰ動力線を結束", "【結束手順 2】ﾘﾆｱﾓｰﾀｰ線θ2ﾓｰﾀｰ動力線θ2ﾓｰﾀｰ信号線を結束", "【結束手順 3】ﾘﾆｱﾓｰﾀｰ線θ2ﾓｰﾀｰ信号線を結束" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ2側基板結束ﾏｰｸﾁｭｰﾌﾞ取付", "WorkItems": [ "1. θ軸ﾓｰﾀｰにﾏｰｷﾝｸﾞﾀｲを取付" ], "WorkPoints": [ "文字が正立で読める様に取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "CN2K301", "CN3K301" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "中継線接続(K301ｰK302)", "WorkItems": [ "1. K302中継線接続" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認", "CN1K302", "CN18K301", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "中継線結束(K301ｰK302)", "WorkItems": [ "1. 略図の手順で結束", "2. 結束後､ﾌﾞﾗｹｯﾄの下側に配線を引き廻す" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【注意】ﾍｯﾄﾞ内部にあるｽﾌﾟﾘﾝｸﾞとの干渉防止の為､略図の様なたすき掛けにして下さい【確認】施工後､配線とｽﾌﾟﾘﾝｸﾞの干渉が無い事を確認して下さい", "【結束手順 1】ﾌﾞﾗｹｯﾄに結束", "【結束手順 2】ﾎﾟｽﾄに結束", "配線はﾌﾞﾗｹｯﾄの下側を通しておく" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1側ﾒｲﾝﾎﾞｰﾄﾞ接続", "WorkItems": [ "1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN10を接続", "2. ﾓｰﾀｰ線の被覆を下略図の様に施工する", "3. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN14を接続", "4. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN15を接続" ], "WorkPoints": [ "【注意】下記の手順にて接続して下さい", "略図にて配線の重なる順序を確認して作業して下さい" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認", "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認", "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "CN14K301ﾀｸﾞはまだ付いていません", "CN10", "CN15K301ﾀｸﾞはまだ付いていませんθ軸ﾓｰﾀｰの信号線です", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1側基板結束1", "WorkItems": [ "1. 略図の順序で結束する" ], "WorkPoints": [ "【注意】断線防止の為､配線を引っ張った状態で結束し無い事", "【注意】結束後､基板と配線の干渉が無い事", "【注意】配線とFANとの干渉が無い事", "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾌﾞﾗｹｯﾄ上側にﾘﾆｱﾓｰﾀｰ線下側にθ1ﾓｰﾀｰ動力線､中継線を結束", "【結束手順 2】θ1ﾓｰﾀｰ動力線θ1ﾓｰﾀｰ信号線を結束", "【結束手順 3】ﾌﾞﾗｹｯﾄにθ1ﾓｰﾀｰ信号線を結束" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1側基板結束2ﾏｰｸﾁｭｰﾌﾞ取付", "WorkItems": [ "1. θ軸ﾓｰﾀｰにﾏｰｷﾝｸﾞﾀｲを取付" ], "WorkPoints": [ "文字が正立で読める様に取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "CN14K301", "CN15K301" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1側基板結束3FAN線接続・結束", "WorkItems": [ "1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN27を接続", "2. 略図の順序で結束" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾌﾞﾗｹｯﾄにFAN線のみを結束【注意】FAN線は干渉防止であまりたるませない", "【結束手順 2】ﾌﾞﾗｹｯﾄにFAN線と中継線を結束", "【結束手順 3】FAN線を折り返しﾌﾞﾗｹｯﾄに中継線と結束", "【注意】FAN線は干渉防止であまりたるませない", "CN27", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱﾓｰﾀｰ信号線接続・結束", "WorkItems": [ "1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN8を接続", "2. 略図の順序で結束" ], "WorkPoints": [ "【注意】配線の曲げ部分がﾌﾞﾗｹｯﾄに干渉してい無い事" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 2】ﾌﾞﾗｹｯﾄに結束", "【結束手順 1】ﾌﾞﾗｹｯﾄに結束曲げ部分が窮屈にならない様にする", "CN8", "【結束手順 3】ﾀｲﾏｳﾝﾄに結束", "【注意】曲げ部分にﾌﾞﾗｹｯﾄとの過度な干渉が無い事", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ線引き回し", "WorkItems": [ "1. ﾄﾞﾛｱｺﾈｸﾀｰ線を引き廻す ※青矢印部分" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "白ｺﾈｸﾀｰ線､黒ｺﾈｸﾀｰ線､FG線を分岐させる" ] }	{ "QualityItem": "引き回確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り経路で配線出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ接続", "WorkItems": [ "1. ｺﾈｸﾀｰを接続する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "CN4", "CN6", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "FAN線接続", "WorkItems": [ "1. FAN線を接続" ], "WorkPoints": [ "略図の様に折り返した後に接続する" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "FAN線/CN28", "GWETJ-F013-002" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ線結束", "WorkItems": [ "1. ﾄﾞﾛｱｺﾈｸﾀｰ線結束" ], "WorkPoints": [ "【注意】ﾄﾞﾛｱｹｰﾌﾞﾙが金属ｴｯｼﾞ部分と干渉のない様にする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾀｲﾏｳﾝﾄに配線を結束", "【結束手順 4】ﾌﾞﾗｹｯﾄに配線を結束", "【結束手順 2】ﾀｲﾏｳﾝﾄに配線を結束", "【結束手順 5】ﾄﾞﾛｱｺﾈｸﾀｰ白ﾁｭｰﾌﾞに配線を結束", "【結束手順 3】ﾓｰﾀｰﾎﾞﾃﾞｨに配線を結束" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ配線・FAN線結束", "WorkItems": [ "1. ﾄﾞﾛｱｺﾈｸﾀｰ･FAN 線結束" ], "WorkPoints": [ "【注意】結束後､ｴｯｼﾞ部分や基板と配線の干渉が無い事", "【注意】ｴｯｼﾞ部分と配線の干渉が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾌﾞﾗｹｯﾄにﾄﾞﾛｱｺﾈｸﾀｰ線とFAN線を結束※折り返したFAN線は結束しない", "【結束手順 2】FAN線を折り返し､ﾄﾞﾛｱｺﾈｸﾀｰ線とﾌﾞﾗｹｯﾄに結束", "【11", "【結束手順 3】ﾌﾞﾗｹｯﾄに結束" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "80cN･m", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ接続", "WorkItems": [ "■1. FG線をSCREW にて締結" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [ "締付ﾄﾙｸ 80cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "80cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾊﾞｰ銘板貼付け", "WorkItems": [ "1. COVER のﾗﾍﾞﾙ貼付面の油分を除去", "2. COVER にLABEL LABEL LABEL を貼付け" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "30mm", "45mm" ] }	{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "60cN･m", "WorkName": "ｶﾊﾞｰ取付", "WorkItems": [ "■1. ①に②をSCREW にて取付" ], "WorkPoints": [ "計8か所を仮固定後､締結する" ], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "付属品ﾊﾟｯｷﾝｸﾞ", "WorkItems": [ "1. SPRING SPRING(BLACK) CLAMP-ARM(BLACK) FILTER TUBE (70MM CUT) をﾊﾟｯｷﾝｸﾞして､付属品とする" ], "WorkPoints": [ "付属品はﾊﾟｯｷﾝｸﾞして､ﾍｯﾄﾞ完成品と合わせて払い出す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "付属品", "合わせて払い出す" ] }	{ "QualityItem": "付属品確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示した付属品を払い出す事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "油砥石", "Size": "", "ToolOther": "", "WorkName": "ｶﾑﾌｫﾛｱ部組立", "WorkItems": [ "1. BRACKET の取付面(青色部)に砥石を掛ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }	{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "打痕、ﾊﾞﾘ無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "5.5㎜(BOX)", "ToolOther": "150cN･m", "WorkName": "ｶﾑﾌｫﾛｱ部組立", "WorkItems": [ "2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｱﾙﾐ用砥石", "Size": "", "ToolOther": "ｽｰﾊﾟｰｼｬｲﾅｰ砥石", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "表面" ] }	{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "打痕、ﾊﾞﾘ無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "表面" ] }	{ "QualityItem": "平面度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "0.1㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5626", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①", "WorkItems": [ "2. ①にBRACKET WASHER をBOLT で取付ける", "1. BRACKET に㉖油砥石を掛ける" ], "WorkPoints": [ "BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事", "①とBRACKET の間にWASHER を挿入する事", "BRACKET を㉗の青点線部に押し当てて取付ける事", "青色部に㉖を掛ける" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "FM-5626", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "250cN･m", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①", "WorkItems": [ "2. ①にBRACKET WASHER をBOLT で取付ける", "1. BRACKET に㉖油砥石を掛ける" ], "WorkPoints": [ "BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事", "①とBRACKET の間にWASHER を挿入する事", "BRACKET を㉗の青点線部に押し当てて取付ける事", "青色部に㉖を掛ける" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5626", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②", "WorkItems": [ "1. ①に②をBOLT で取付ける" ], "WorkPoints": [ "②を㉖の青点線部に押し当てて取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "FM-5626", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "250cN･m", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②", "WorkItems": [ "1. ①に②をBOLT で取付ける" ], "WorkPoints": [ "②を㉖の青点線部に押し当てて取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "油砥石", "Size": "", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③", "WorkItems": [ "2. ①にBLOCK をBOLT で取付ける", "1. BLOCK に㉖油砥石を掛ける" ], "WorkPoints": [ "BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事", "青色部に㉖を掛ける（面取りが無い側）", "BLOCK の面取り位置を図左手前にして取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "打痕、ﾊﾞﾘ無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5626", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③", "WorkItems": [ "2. ①にBLOCK をBOLT で取付ける", "1. BLOCK に㉖油砥石を掛ける" ], "WorkPoints": [ "BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事", "青色部に㉖を掛ける（面取りが無い側）", "BLOCK の面取り位置を図左手前にして取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "FM-5626", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "250cN･m", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③", "WorkItems": [ "2. ①にBLOCK をBOLT で取付ける", "1. BLOCK に㉖油砥石を掛ける" ], "WorkPoints": [ "BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事", "青色部に㉖を掛ける（面取りが無い側）", "BLOCK の面取り位置を図左手前にして取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "250cN･m", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④", "WorkItems": [ "1. ①にGUIDE をBOLT WASHER NUT で取付ける" ], "WorkPoints": [ "GUIDE は各々外側(矢印方向)に寄せて取付ける事(傾き無き事)" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "交換台車支持部(右)1", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "PIN出代:4㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "13㎜BOX", "ToolOther": "12.7N･m", "WorkName": "交換台車支持部(右)1", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "12.7N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "26.5N･m", "WorkName": "交換台車支持部(右)2", "WorkItems": [ "1. ①にCAM-FOLLOWER を取付ける" ], "WorkPoints": [ "付属ﾅｯﾄ" ], "Tolks": [ "締付ﾄﾙｸ 26.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "26.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.5N･m", "WorkName": "交換台車支持部(右)2", "WorkItems": [ "2. 1完成品にGUIDE をSPACER BOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "当付け方向" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "20N･m", "WorkName": "交換台車支持部(右)3", "WorkItems": [ "1. FRAME(R) に①BLOCK をBOLT で取付ける" ], "WorkPoints": [ "当付け方向", "当付け方向", "17/34連+17/34連仕様の取付け位置", "17/34連 + ﾄﾚｲ仕様の取付け位置" ], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "20N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "交換台車支持部(右)4", "WorkItems": [ "1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "面位置", "矢印方向に押し当てて取付ける" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "5.3N･m", "WorkName": "交換台車支持部(右)4", "WorkItems": [ "2. 1完成品をBRACKET にBOLT WASHER BOLT ㉒で取付ける" ], "WorkPoints": [ "長穴ｾﾝﾀｰに合せる", "前側取付位置", "後側取付位置" ], "Tolks": [ "締付ﾄﾙｸ 5.3N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "5.3N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "交換台車支持部(右)5", "WorkItems": [ "1. ①にCOVER をBOLT WASHER で取付ける" ], "WorkPoints": [ "ﾄﾚｲ仕様", "台車仕様", "ﾄﾚｲ仕様", "台車仕様" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "前側取付位置", "後側取付位置" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "6.0N･m", "WorkName": "交換台車支持部(右)6", "WorkItems": [ "1. ①に②をBOLT WASHER で取付ける" ], "WorkPoints": [ "面位置合せ" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "20N･m", "WorkName": "交換台車支持部(右)7", "WorkItems": [ "1. ①にBRACKET をBOLT WASHER で取付ける", "2. 1完成品にCOVER をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "20N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "交換台車支持部(右)7", "WorkItems": [ "1. ①にBRACKET をBOLT WASHER で取付ける", "2. 1完成品にCOVER をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(前側&右側)1", "WorkItems": [ "1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "平行に取付の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(前側&右側)2", "WorkItems": [ "1. ①にBRACKET をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾙｰ部品30連/60連(前側&右側)", "WorkItems": [ "1. H1工程へ払い出す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "部品準備", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示した部品を払い出す事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)1", "WorkItems": [ "1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "平行に取付の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)2", "WorkItems": [], "WorkPoints": [ "面位置に取付の事", "平行に取付の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "8㎜" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "各194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)2", "WorkItems": [], "WorkPoints": [ "面位置に取付の事", "平行に取付の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "8㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法8.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾙｰ部品30連/60連(後側&右側)", "WorkItems": [ "1. PLUG を払い出す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "部品準備", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示した部品を払い出す事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｶﾑﾌｫﾛｱ部組立", "WorkItems": [ "1. BRACKET の取付面(黄色部)に砥石を掛ける", "2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける" ], "WorkPoints": [ "CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい", "この作業では同じものを4個製作" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "油砥石", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "5.5㎜(BOX)", "ToolOther": "150cN･m", "WorkName": "ｶﾑﾌｫﾛｱ部組立", "WorkItems": [ "2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける" ], "WorkPoints": [ "CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備", "WorkItems": [ "2. PLATE の平面度を測定する", "1. PLATE の両面に㉖を掛ける" ], "WorkPoints": [ "表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事", "PLATE に打痕やﾊﾞﾘが無い事", "緑色部の9箇所を測定する事(平面度:0.1㎜以内)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "表面", "裏面", "この作業では同じものを2個製作" ] }	{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "ｱﾙﾐ用砥石", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備", "WorkItems": [ "1. PLATE の両面に㉖を掛ける" ], "WorkPoints": [ "表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事", "PLATE に打痕やﾊﾞﾘが無い事", "緑色部の9箇所を測定する事(平面度:0.1㎜以内)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "表面", "この作業では同じものを2個製作" ] }	{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "0.1㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①", "WorkItems": [ "1. GUIDE に㉖油砥石を掛ける", "2. ①にGUIDE をBOLT で取付ける" ], "WorkPoints": [ "GUIDE を㉗に押し当てて取付ける事", "黄色部に㉖を掛ける", "GUIDE の全面にﾊﾞﾘ､打痕等ないか確認する事", "①の座ｸﾞﾘ面が無い方面に取付ける事", "㉗ナットの向きに注意してピンを①まで挿入して取付ける", "座ぐり穴の所にBOLT を入れる" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }	{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "油砥石", "ProcessNames": [] }	information_extraction	null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ摺動確認", "WorkItems": [ "1. ﾉｽﾞﾙﾎﾙﾀﾞ摺動確認" ], "WorkPoints": [ "【確認方法】 ※全ﾉｽﾞﾙ実施手順1 ﾉｽﾞﾙﾎﾙﾀﾞｰ先端を指で押し(黄色矢印)､ﾊﾞﾈにて摺動する事を確認手順2 ﾉｽﾞﾙﾎﾙﾀﾞｰを180°回転させて再取付手順3 再度､ﾉｽﾞﾙﾎﾙﾀﾞｰ先端を指で押し､ﾊﾞﾈにて摺動する事を確認" ], "Tolks": [], "InspectionNo": "GWETJ-F013-001", "InspectionItems": [ "検査表①:ﾉｽﾞﾙﾎﾙﾀﾞ摺動確認" ], "WorkTypes": [], "Words": [ "GWETJ-F013-001" ] }

{ "QualityItem": "摺動確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "滑らかに動く事", "Method": "目視/手感", "RecordMethod": "GWETJ-F013-001", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "100cN･m", "WorkName": "θ原点ﾄﾞｸﾞｶﾊﾞｰ取付", "WorkItems": [ "1. ①にCOVER COVER をBOLT にて取付" ], "WorkPoints": [ "【確認】原点ﾄﾞｸﾞにｸﾞﾘｰｽが塗られている事" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "ﾉｽﾞﾙｶﾞｰﾄﾞ取付", "WorkItems": [ "1. ①にCOVER をBOLT WASHER で取付" ], "WorkPoints": [ "【取付ﾎﾟｲﾝﾄ】黄色矢印方向に押し付けながら締結 ※左右の高さを揃えるため" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "1.5㎜", "ToolOther": "50cN･m", "WorkName": "整定板ｶﾊﾞｰ取付", "WorkItems": [ "1. ①にCOVER をBOLT WASHER で取付", "2. 取付確認" ], "WorkPoints": [ "【注意】 COVER 取付後､ｽﾌﾟﾗｲﾝを摺動させて干渉無き事", "COVER 取付後､全ﾉｽﾞﾙﾍﾞｱﾘﾝｸﾞ(黄色部分)がｶﾊﾞｰ(黒色部分)と干渉してい無い事", "ﾉｽﾞﾙを手で摺動させ確認" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾉｽﾞﾙﾍﾞｱﾘﾝｸﾞ(黄)", "ｶﾊﾞｰ(黒)", "制定ﾌﾟﾚｰﾄ(青)" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "50cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾁｭｰﾌﾞ取付", "WorkItems": [ "◆1. TUBE (70MM CUT) をｴｱｰｶﾞﾝにて､清掃する", "2. ①にTUBE (70MM CUT) を取付" ], "WorkPoints": [ "ﾁｭｰﾌﾞ取付け後､ｽﾌﾟﾗｲﾝｼｬﾌﾄが上昇端まで上がることを確認", "TUBE (70MM CUT) は8本取付", "【注意】保護ﾒｶﾞﾈ着用の事", "【取付注意】ﾁｭｰﾌﾞは継手根本まで差込む事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｺﾞﾐ､埃が無い事", "Method": "目視", "RecordMethod": "-", "Other": "保護ﾒｶﾞﾈ", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "60cN･m", "WorkName": "ﾀｲﾏｳﾝﾄ取付", "WorkItems": [ "1. ①にCABLE-SUPPORT BOLT CABLE-SUPPORT BOLT を取付" ], "WorkPoints": [ "【取付目安】 CABLE-SUPPORT は約45度傾けて取付 ※略図参照" ], "Tolks": [ "BOLT 締付ﾄﾙｸ 100cN･m ﾎﾞﾀﾝﾎﾞﾙﾄ", "BOLT 締付ﾄﾙｸ 60cN･m 皿ﾎﾞﾙﾄ" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "正面", "背面", "左側面", "右側面" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "ﾀｲﾏｳﾝﾄ取付", "WorkItems": [ "1. ①にCABLE-SUPPORT BOLT CABLE-SUPPORT BOLT を取付" ], "WorkPoints": [ "【取付目安】 CABLE-SUPPORT は約45度傾けて取付 ※略図参照" ], "Tolks": [ "BOLT 締付ﾄﾙｸ 100cN･m ﾎﾞﾀﾝﾎﾞﾙﾄ", "BOLT 締付ﾄﾙｸ 60cN･m 皿ﾎﾞﾙﾄ" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "正面", "背面", "左側面", "右側面" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP1~NP4ﾌﾛｰｾﾝｻｰ接続/結束1", "WorkItems": [ "2. ﾌﾞﾗｹｯﾄに結束", "1. ①のﾌﾛｰｾﾝｻｰにCABLE ｺﾈｸﾀｰを接続" ], "WorkPoints": [ "【注意】ｲﾝｼｭﾛｯｸの頭の向きは下側", "【注意】ｲﾝｼｭﾛｯｸの頭の向きは外側", "詳細は検査表参照", "一部を省いて描いています", "ｺﾈｸﾀｰﾗﾍﾞﾙを確認後､接続" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾌﾛｰｾﾝｻ接続確認(NP1~NP4)" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "F1", "F2", "F3", "F4", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP1~NP4ﾌﾛｰｾﾝｻｰ接続/結束2", "WorkItems": [ "1. ﾌﾛｰｾﾝｻｰ線とθ2軸原点ｾﾝｻｰ線を仮結束" ], "WorkPoints": [ "一部を省いて描いています", "仮結束です", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP1~NP4真空(V)/ﾌﾞﾛｰ(B)ﾊﾞﾙﾌﾞ接続確認1", "WorkItems": [ "1. ①のﾊﾞﾙﾌﾞ(NP1~NP4 真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ)にCABLE を接続" ], "WorkPoints": [ "詳細は検査表参照", "一部を省いて描いています", "ｺﾈｸﾀｰﾗﾍﾞﾙを確認後､接続" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ接続確認(NP1~NP4)" ], "WorkTypes": [], "Words": [ "NP1V1", "NP1B1", "NP2V2", "NP2B2", "NP3V3", "NP3B3", "NP4V4", "NP4B4", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP1~NP4真空(V)/ﾌﾞﾛｰ(B)ﾊﾞﾙﾌﾞ接続確認2", "WorkItems": [ "1. NP1~NP4 真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ線をﾀｲﾏｳﾝﾄに仮結束", "2. 配線のみを結束" ], "WorkPoints": [ "仮結束です", "3本のみ略図の位置に結束です", "B3､V4､B4線を結束 ※略図参照", "一部を省いて描いています", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "B3", "V4", "B4" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1原点ｾﾝｻｰ線引き回", "WorkItems": [ "1. ①のθ1原点ｾﾝｻｰ線を仮結束" ], "WorkPoints": [ "一部を省いて描いています", "仮結束です" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP5~NP8ﾌﾛｰｾﾝｻｰ接続/結束1", "WorkItems": [ "1. ①のﾌﾛｰｾﾝｻｰにCABLE ｺﾈｸﾀｰを接続", "2. ﾌﾞﾗｹｯﾄに結束" ], "WorkPoints": [ "【注意】ｲﾝｼｭﾛｯｸの頭の向きは下側", "【注意】ｲﾝｼｭﾛｯｸの頭の向きは外側", "詳細は検査表参照", "一部を省いて描いています", "ｺﾈｸﾀｰﾗﾍﾞﾙを確認後､接続" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾌﾛｰｾﾝｻ接続確認(NP5~NP8)" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "F8", "F7", "F6", "F5", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP5~NP8ﾌﾛｰｾﾝｻｰ接続/結束2", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP5~NP8真空(V)/ﾌﾞﾛｰ(B)ﾊﾞﾙﾌﾞ接続確認1", "WorkItems": [ "1. ①のﾊﾞﾙﾌﾞ(NP5~NP8 真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ)にCABLE を接続" ], "WorkPoints": [ "詳細は検査表参照", "一部を省いて描いています", "ｺﾈｸﾀｰﾗﾍﾞﾙを確認後､接続" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ接続確認(NP5~NP8)" ], "WorkTypes": [], "Words": [ "NP8V8", "NP8B8", "NP7V7", "NP7B7", "NP6V6", "NP6B6", "NP5V5", "NP5B5", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "NP5~NP8真空(V)/ﾌﾞﾛｰ(B)ﾊﾞﾙﾌﾞ接続確認2", "WorkItems": [ "2. 配線を結束", "1. NP5~NP8 真空/ﾌﾞﾛｰﾊﾞﾙﾌﾞ線をﾀｲﾏｳﾝﾄに仮結束" ], "WorkPoints": [ "一部を省いて描いています", "仮結束です", "3本のみ略図の位置に結束です", "B5､B6､V6線を結束 ※略図参照", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束", "【注意】ﾀｲﾏｳﾝﾄの片側のみに結束" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "B6", "V5", "B5" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ固定ｼﾞｸ", "Size": "", "ToolOther": "FM-5717", "WorkName": "θ軸ﾕﾆｯﾄ取付", "WorkItems": [ "4. ②取付後、㉖治具を静かに取り外す", "1. ②に㉖治具を取付", "◆2. ﾗﾐﾀﾓｰﾀｰ先端ﾌﾞﾛｯｸにｸﾞﾘｰｽ塗布", "3. ①に2完成品をBOLT BOLT WASHER にて取付" ], "WorkPoints": [ "【注意】　配線の嚙み込みや干渉が無い事", "【注意】ﾎﾞﾙﾄ長さが異なる ※略図参照", "①のﾋﾟﾝに嵌合させて取付", "ノズルシャフトを手で押し下げて、制定プレートとノズルブロックの間に㉖治具を設置する", "治具㉖は黄色で表示しています", "一部を省いて描いています", "略図青色部分にｸﾞﾘｰｽ塗布" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布米粒:8" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "FM-5717", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ軸ﾕﾆｯﾄ取付", "WorkItems": [ "4. ②取付後、㉖治具を静かに取り外す", "1. ②に㉖治具を取付", "◆2. ﾗﾐﾀﾓｰﾀｰ先端ﾌﾞﾛｯｸにｸﾞﾘｰｽ塗布", "3. ①に2完成品をBOLT BOLT WASHER にて取付" ], "WorkPoints": [ "【注意】　配線の嚙み込みや干渉が無い事", "【注意】ﾎﾞﾙﾄ長さが異なる ※略図参照", "①のﾋﾟﾝに嵌合させて取付", "ノズルシャフトを手で押し下げて、制定プレートとノズルブロックの間に㉖治具を設置する", "治具㉖は黄色で表示しています", "一部を省いて描いています", "略図青色部分にｸﾞﾘｰｽ塗布" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布米粒:8" ] }

{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "米粒:8", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "θ軸ﾕﾆｯﾄ取付", "WorkItems": [ "4. ②取付後、㉖治具を静かに取り外す", "3. ①に2完成品をBOLT BOLT WASHER にて取付" ], "WorkPoints": [ "【注意】　配線の嚙み込みや干渉が無い事", "【注意】ﾎﾞﾙﾄ長さが異なる ※略図参照", "①のﾋﾟﾝに嵌合させて取付" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "◆作業者安全作業" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱﾓｰﾀｰ連結部品取付", "WorkItems": [ "◆1. BRACKET の指定箇所にｸﾞﾘｰｽを塗布する", "2. ①に1完成品をBOLT にて取付", "3. Z軸摺動確認 (全8軸)" ], "WorkPoints": [ "【BRACKET の傾きを押さえる締付方法】BOLT のﾎﾞﾙﾄにﾚﾝﾁを挿入し､青矢印方向にﾉｽﾞﾙﾎﾙﾀﾞｰ(ｽﾌﾟﾗｲﾝｼｬﾌﾄ)を引っ張った状態でBOLT を締結", "一部を省いて描いています", "【注意】締結時､ﾄﾙｸﾄﾞﾗｲﾊﾞｰを押し過ぎて､ﾘﾆｱﾓｰﾀｼｬﾌﾄに過大な力をかけ無い事", "【注意】ﾊﾞﾈを圧縮した状態から放すと､勢いよく上昇し衝撃で破損します", "【確認方法】ﾉｽﾞﾙﾎﾙﾀﾞｰを1mm程指で引っ張り､静かに放しﾊﾞﾈで上端まで戻る事を確認する", "【注意】 BRACKET は位置決めﾋﾟﾝに確実に嵌合されている事", "【注意】 BRACKET の先端部分が隙間に挿入されている事" ], "Tolks": [ "締付ﾄﾙｸ 30cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "位置決めﾋﾟﾝ", "隙間に挿入させる", "ｸﾞﾘｰｽ塗布位置", "ｸﾞﾘｰｽ塗布ｺﾞﾏ粒:1 計ｺﾞﾏ粒:8", "確実に嵌合させる", "検査表①:Z軸上昇確認" ] }

{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｺﾞﾏ粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "1.5㎜", "ToolOther": "30cN･m", "WorkName": "ﾘﾆｱﾓｰﾀｰ連結部品取付", "WorkItems": [ "◆1. BRACKET の指定箇所にｸﾞﾘｰｽを塗布する", "2. ①に1完成品をBOLT にて取付" ], "WorkPoints": [ "【BRACKET の傾きを押さえる締付方法】BOLT のﾎﾞﾙﾄにﾚﾝﾁを挿入し､青矢印方向にﾉｽﾞﾙﾎﾙﾀﾞｰ(ｽﾌﾟﾗｲﾝｼｬﾌﾄ)を引っ張った状態でBOLT を締結", "一部を省いて描いています", "【注意】締結時､ﾄﾙｸﾄﾞﾗｲﾊﾞｰを押し過ぎて､ﾘﾆｱﾓｰﾀｼｬﾌﾄに過大な力をかけ無い事", "【注意】 BRACKET は位置決めﾋﾟﾝに確実に嵌合されている事", "【注意】 BRACKET の先端部分が隙間に挿入されている事" ], "Tolks": [ "締付ﾄﾙｸ 30cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布位置", "ｸﾞﾘｰｽ塗布ｺﾞﾏ粒:1 計ｺﾞﾏ粒:8", "◆作業者安全作業" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "30cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱﾓｰﾀｰ連結部品取付", "WorkItems": [ "◆1. BRACKET の指定箇所にｸﾞﾘｰｽを塗布する", "2. ①に1完成品をBOLT にて取付", "3. Z軸摺動確認 (全8軸)" ], "WorkPoints": [ "【BRACKET の傾きを押さえる締付方法】BOLT のﾎﾞﾙﾄにﾚﾝﾁを挿入し､青矢印方向にﾉｽﾞﾙﾎﾙﾀﾞｰ(ｽﾌﾟﾗｲﾝｼｬﾌﾄ)を引っ張った状態でBOLT を締結", "一部を省いて描いています", "【注意】締結時､ﾄﾙｸﾄﾞﾗｲﾊﾞｰを押し過ぎて､ﾘﾆｱﾓｰﾀｼｬﾌﾄに過大な力をかけ無い事", "【注意】ﾊﾞﾈを圧縮した状態から放すと､勢いよく上昇し衝撃で破損します", "【確認方法】ﾉｽﾞﾙﾎﾙﾀﾞｰを1mm程指で引っ張り､静かに放しﾊﾞﾈで上端まで戻る事を確認する", "【注意】 BRACKET は位置決めﾋﾟﾝに確実に嵌合されている事", "【注意】 BRACKET の先端部分が隙間に挿入されている事" ], "Tolks": [ "締付ﾄﾙｸ 30cN･m" ], "InspectionNo": "GWETJ-F013-001", "InspectionItems": [ "検査表①:Z軸上昇確認" ], "WorkTypes": [], "Words": [ "位置決めﾋﾟﾝ", "隙間に挿入させる", "ｸﾞﾘｰｽ塗布位置", "ｸﾞﾘｰｽ塗布ｺﾞﾏ粒:1 計ｺﾞﾏ粒:8", "確実に嵌合させる", "GWETJ-F013-001" ] }

{ "QualityItem": "摺動確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "上端ﾒｶｽﾄまで上がること(8軸)", "Method": "目視", "RecordMethod": "GWETJ-F013-001", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付1", "WorkItems": [ "1. ①に②③をBOLT WASHER にて取付" ], "WorkPoints": [ "一部を省いて描いています", "全てのﾎﾞﾙﾄを取付後､均一に締結する", "【取付目安】 115mmを目安に取付 ※略図参照" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付1", "WorkItems": [ "1. ①に②③をBOLT WASHER にて取付" ], "WorkPoints": [ "一部を省いて描いています", "全てのﾎﾞﾙﾄを取付後､均一に締結する", "【取付目安】 115mmを目安に取付 ※略図参照" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付2", "WorkItems": [ "1. ①にCOVER をSPACER BOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付2", "WorkItems": [ "1. ①にCOVER をSPACER BOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)周辺取付2", "WorkItems": [ "1. ①にCOVER をSPACER BOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)接続", "WorkItems": [ "■★1. FC08 IO BOARD I/Oﾎﾞｰﾄﾞ1(K302)の型式･検査書確認", "★2. I/Oﾎﾞｰﾄﾞ(K302) (CN3､CN4､CN10)を接続" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認" ], "WorkTypes": [], "Words": [ "K302I/Oﾎﾞｰﾄﾞ1", "検査表①:型式･検査書確認", "GWETJ-F013-002" ] }

{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙ番号転記", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)接続", "WorkItems": [ "■★1. FC08 IO BOARD I/Oﾎﾞｰﾄﾞ1(K302)の型式･検査書確認", "★2. I/Oﾎﾞｰﾄﾞ(K302) (CN3､CN4､CN10)を接続" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:型式･検査書確認" ], "WorkTypes": [], "Words": [ "K302I/Oﾎﾞｰﾄﾞ1", "検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "5㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ1(K302)取付", "WorkItems": [ "■1. I/Oﾎﾞｰﾄﾞ1(K302)をBOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "CN3、CN4、CN10を本結束", "WorkItems": [ "1. 仮結束のｲﾝｼｭﾛｯｸを本結束する" ], "WorkPoints": [ "配線を微調整して､仮結束のｲﾝｼｭﾛｯｸを本結束して下さい", "【確認】心線が可動部やｴｯｼﾞ部に干渉していないか確認" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾒｲﾝﾎﾞｰﾄﾞ(K301)取付", "WorkItems": [ "■★1. FC08 MAIN BOARD ﾒｲﾝﾎﾞｰﾄﾞの型式･検査書確認", "■★2. FC08 MAIN BOARD ﾒｲﾝﾎﾞｰﾄﾞをBOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 80cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:型式･検査書確認" ], "WorkTypes": [], "Words": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認", "GWETJ-F013-002" ] }

{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙ番号転記", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "80cN･m", "WorkName": "ﾒｲﾝﾎﾞｰﾄﾞ(K301)取付", "WorkItems": [ "■★1. FC08 MAIN BOARD ﾒｲﾝﾎﾞｰﾄﾞの型式･検査書確認", "■★2. FC08 MAIN BOARD ﾒｲﾝﾎﾞｰﾄﾞをBOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 80cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "検査表①:型式･検査書確認", "■安全作業", "★静電対策作業" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "80cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)接続", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [], "WorkTypes": [], "Words": [ "GWETJ-F013-002" ] }

{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙ番号転記", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)接続", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [], "WorkTypes": [], "Words": [ "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "60cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)取付", "WorkItems": [ "■1. I/Oﾎﾞｰﾄﾞ2(K303)を本締め" ], "WorkPoints": [ "一部を省いて描いています", "【注意】ｺﾈｸﾀｰの接続に配慮して無理な力は極力避けて作業する", "【注意】基板取付後､ｺﾈｸﾀｰの接続が確実か確認する", "【重要】ｺﾈｸﾀｰ心線が上空方向に膨らむと､後工程にてｶﾊﾞｰと干渉する恐れあり", "SD-A036545-007の本締め" ], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)中継配線接続", "WorkItems": [ "1. I/Oﾎﾞｰﾄﾞ2(K303)中継線接続" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認" ], "WorkTypes": [], "Words": [ "検査表①:IOﾎﾞｰﾄﾞ2(K303)接続確認", "CN1K303", "CN2K302", "正面", "背面", "左側面", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "I/Oﾎﾞｰﾄﾞ2結束", "WorkItems": [ "1. I/Oﾎﾞｰﾄﾞ2(303)中継配線を結束(1箇所のみ)", "2. I/Oﾎﾞｰﾄﾞ2(K303)の仮結束部分を結束する (3箇所)" ], "WorkPoints": [ "【注意】 1箇所のみ結束", "【結束目安】ｺﾈｸﾀｰにｽﾄﾚｽの少ない位置で結束", "配線を微調整して､仮結束のｲﾝｼｭﾛｯｸを本結束して下さい", "【確認】心線が可動部やｴｯｼﾞ部に干渉していないか確認" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.1", "ToolOther": "50cN･m", "WorkName": "I/Oﾎﾞｰﾄﾞ2(K303)基板ｶﾊﾞｰ取付", "WorkItems": [ "■1. ①にCOVER をSCREW にて取付" ], "WorkPoints": [ "一部を省いて描いています", "【重要】ｶﾊﾞｰ取付後に各心線やｺﾈｸﾀｰが､ｶﾊﾞｰと干渉していないか確認する" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "50cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "ｴｱﾁｭｰﾌﾞｶｯﾄ", "WorkItems": [ "1. ｴｱﾁｭｰﾌﾞを指定寸法にｶｯﾄ" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｱﾁｭｰﾌﾞ接続", "WorkItems": [ "1. ｴｱﾁｭｰﾌﾞを接続" ], "WorkPoints": [ "一部を省いて描いています", "【注意】ｴｱﾁｭｰﾌﾞは確実に接続する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "③黄色 265mm", "②黄色 270mm", "⑤白色 210mm", "④白色 235mm", "④白色 235mm", "⑤白色 210mm" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｱﾁｭｰﾌﾞ接続・結束1", "WorkItems": [ "1. 略図の様にｴｱﾁｭｰﾌﾞを接続", "2. 略図の順序で結束する" ], "WorkPoints": [ "ｴｱﾁｭｰﾌﾞは確実に接続する事", "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ｴｱﾁｭｰﾌﾞのみ結束(ﾗﾌ原点ｾﾝｻｰ線は結束しない)", "【結束手順 2】ｴｱﾁｭｰﾌﾞどうしを結束", "【結束手順 3】ﾌﾞﾗｹｯﾄに結束", "【結束手順 4】ｴｱﾁｭｰﾌﾞどうしを結束", "【結束手順 5】ﾀｲﾏｳﾝﾄに結束" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1原点ｾﾝｻｰ線結束", "WorkItems": [ "1. 仮結束の部分を結束", "2. θ軸原点ｾﾝｻｰ線を結束" ], "WorkPoints": [ "ｴｱﾁｭｰﾌﾞに結束する", "【確認】結束後､過度な干渉が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｱﾁｭｰﾌﾞ接続・結束2", "WorkItems": [ "1. 略図の様にｴｱﾁｭｰﾌﾞを接続", "2. 略図の順序で結束する" ], "WorkPoints": [ "一部を省いて描いています", "ｴｱﾁｭｰﾌﾞは確実に接続する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ｴｱﾁｭｰﾌﾞと配線を結束", "【結束手順 4】ﾌﾞﾗｹｯﾄにｴｱﾁｭｰﾌﾞと配線を結束", "【結束手順 3】ｴｱﾁｭｰﾌﾞと配線を結束", "【結束手順 2】配線をﾀｲﾏｳﾝﾄに結束※2ｶ所", "【結束手順 5】ﾀｲﾏｳﾝﾄに結束", "【結束手順 6】ｴｱﾁｭｰﾌﾞどうしを結束" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "配管取付確認", "WorkItems": [ "1. 配管取付確認" ], "WorkPoints": [ "略図の様に㉖スケールをセットし、配管が干渉していないか確認" ], "Tolks": [], "InspectionNo": "GWETJ-F013-001", "InspectionItems": [ "検査表①:配管取付け確認" ], "WorkTypes": [], "Words": [ "㉖スケール" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "BRACKETより飛出してい無い事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "中継線結束", "WorkItems": [ "1. 中継線をﾎﾟｽﾄに結束" ], "WorkPoints": [ "【注意】ﾍｯﾄﾞ内部にあるｽﾌﾟﾘﾝｸﾞとの干渉防止の為､心線が上に向く様に結束", "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "【注意】ﾍｯﾄﾞ内部にあるｽﾌﾟﾘﾝｸﾞとの干渉防止の為､略図の様なたすき掛けにして下さい【確認】施工後､ｽﾌﾟﾘﾝｸﾞと干渉が無い事を確認して下さい", "ｶﾊﾞｰﾎﾟｽﾄに配線を結束", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ2側ﾒｲﾝﾎﾞｰﾄﾞ接続", "WorkItems": [ "1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN7を接続", "2. ﾓｰﾀｰ線の被覆を下略図の様に施工する", "3. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN2を接続", "4. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN3を接続" ], "WorkPoints": [ "【注意】下記の手順にて接続して下さい", "略図にて配線の重なる順序を確認して作業して下さい" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認", "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認", "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "CN3K301ﾀｸﾞはまだ付いていませんθ軸ﾓｰﾀｰの信号線です", "CN2K301ﾀｸﾞはまだ付いていません", "CN7", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ2側基板結束", "WorkItems": [ "1. 略図の順序で結束する" ], "WorkPoints": [ "一部を省いて描いています", "【注意】断線防止の為､配線を引っ張った状態で結束し無い事", "【注意】基板と配線の干渉が無い事", "【注意】配線とFANとの干渉が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾌﾞﾗｹｯﾄ上側にﾘﾆｱﾓｰﾀｰ線下側にθ2ﾓｰﾀｰ動力線を結束", "【結束手順 2】ﾘﾆｱﾓｰﾀｰ線θ2ﾓｰﾀｰ動力線θ2ﾓｰﾀｰ信号線を結束", "【結束手順 3】ﾘﾆｱﾓｰﾀｰ線θ2ﾓｰﾀｰ信号線を結束" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ2側基板結束ﾏｰｸﾁｭｰﾌﾞ取付", "WorkItems": [ "1. θ軸ﾓｰﾀｰにﾏｰｷﾝｸﾞﾀｲを取付" ], "WorkPoints": [ "文字が正立で読める様に取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "CN2K301", "CN3K301" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "中継線接続(K301ｰK302)", "WorkItems": [ "1. K302中継線接続" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "検査表①:IOﾎﾞｰﾄﾞ1(K302)接続確認", "CN1K302", "CN18K301", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "中継線結束(K301ｰK302)", "WorkItems": [ "1. 略図の手順で結束", "2. 結束後､ﾌﾞﾗｹｯﾄの下側に配線を引き廻す" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【注意】ﾍｯﾄﾞ内部にあるｽﾌﾟﾘﾝｸﾞとの干渉防止の為､略図の様なたすき掛けにして下さい【確認】施工後､配線とｽﾌﾟﾘﾝｸﾞの干渉が無い事を確認して下さい", "【結束手順 1】ﾌﾞﾗｹｯﾄに結束", "【結束手順 2】ﾎﾟｽﾄに結束", "配線はﾌﾞﾗｹｯﾄの下側を通しておく" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1側ﾒｲﾝﾎﾞｰﾄﾞ接続", "WorkItems": [ "1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN10を接続", "2. ﾓｰﾀｰ線の被覆を下略図の様に施工する", "3. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN14を接続", "4. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN15を接続" ], "WorkPoints": [ "【注意】下記の手順にて接続して下さい", "略図にて配線の重なる順序を確認して作業して下さい" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認", "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認", "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "CN14K301ﾀｸﾞはまだ付いていません", "CN10", "CN15K301ﾀｸﾞはまだ付いていませんθ軸ﾓｰﾀｰの信号線です", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1側基板結束1", "WorkItems": [ "1. 略図の順序で結束する" ], "WorkPoints": [ "【注意】断線防止の為､配線を引っ張った状態で結束し無い事", "【注意】結束後､基板と配線の干渉が無い事", "【注意】配線とFANとの干渉が無い事", "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾌﾞﾗｹｯﾄ上側にﾘﾆｱﾓｰﾀｰ線下側にθ1ﾓｰﾀｰ動力線､中継線を結束", "【結束手順 2】θ1ﾓｰﾀｰ動力線θ1ﾓｰﾀｰ信号線を結束", "【結束手順 3】ﾌﾞﾗｹｯﾄにθ1ﾓｰﾀｰ信号線を結束" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1側基板結束2ﾏｰｸﾁｭｰﾌﾞ取付", "WorkItems": [ "1. θ軸ﾓｰﾀｰにﾏｰｷﾝｸﾞﾀｲを取付" ], "WorkPoints": [ "文字が正立で読める様に取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "CN14K301", "CN15K301" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "θ1側基板結束3FAN線接続・結束", "WorkItems": [ "1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN27を接続", "2. 略図の順序で結束" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾌﾞﾗｹｯﾄにFAN線のみを結束【注意】FAN線は干渉防止であまりたるませない", "【結束手順 2】ﾌﾞﾗｹｯﾄにFAN線と中継線を結束", "【結束手順 3】FAN線を折り返しﾌﾞﾗｹｯﾄに中継線と結束", "【注意】FAN線は干渉防止であまりたるませない", "CN27", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱﾓｰﾀｰ信号線接続・結束", "WorkItems": [ "1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN8を接続", "2. 略図の順序で結束" ], "WorkPoints": [ "【注意】配線の曲げ部分がﾌﾞﾗｹｯﾄに干渉してい無い事" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 2】ﾌﾞﾗｹｯﾄに結束", "【結束手順 1】ﾌﾞﾗｹｯﾄに結束曲げ部分が窮屈にならない様にする", "CN8", "【結束手順 3】ﾀｲﾏｳﾝﾄに結束", "【注意】曲げ部分にﾌﾞﾗｹｯﾄとの過度な干渉が無い事", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ線引き回し", "WorkItems": [ "1. ﾄﾞﾛｱｺﾈｸﾀｰ線を引き廻す ※青矢印部分" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "白ｺﾈｸﾀｰ線､黒ｺﾈｸﾀｰ線､FG線を分岐させる" ] }

{ "QualityItem": "引き回確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り経路で配線出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ接続", "WorkItems": [ "1. ｺﾈｸﾀｰを接続する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "CN4", "CN6", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "FAN線接続", "WorkItems": [ "1. FAN線を接続" ], "WorkPoints": [ "略図の様に折り返した後に接続する" ], "Tolks": [], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認" ], "WorkTypes": [], "Words": [ "FAN線/CN28", "GWETJ-F013-002" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-002", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ線結束", "WorkItems": [ "1. ﾄﾞﾛｱｺﾈｸﾀｰ線結束" ], "WorkPoints": [ "【注意】ﾄﾞﾛｱｹｰﾌﾞﾙが金属ｴｯｼﾞ部分と干渉のない様にする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾀｲﾏｳﾝﾄに配線を結束", "【結束手順 4】ﾌﾞﾗｹｯﾄに配線を結束", "【結束手順 2】ﾀｲﾏｳﾝﾄに配線を結束", "【結束手順 5】ﾄﾞﾛｱｺﾈｸﾀｰ白ﾁｭｰﾌﾞに配線を結束", "【結束手順 3】ﾓｰﾀｰﾎﾞﾃﾞｨに配線を結束" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ配線・FAN線結束", "WorkItems": [ "1. ﾄﾞﾛｱｺﾈｸﾀｰ･FAN 線結束" ], "WorkPoints": [ "【注意】結束後､ｴｯｼﾞ部分や基板と配線の干渉が無い事", "【注意】ｴｯｼﾞ部分と配線の干渉が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "【結束手順 1】ﾌﾞﾗｹｯﾄにﾄﾞﾛｱｺﾈｸﾀｰ線とFAN線を結束※折り返したFAN線は結束しない", "【結束手順 2】FAN線を折り返し､ﾄﾞﾛｱｺﾈｸﾀｰ線とﾌﾞﾗｹｯﾄに結束", "【11", "【結束手順 3】ﾌﾞﾗｹｯﾄに結束" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "80cN･m", "WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ接続", "WorkItems": [ "■1. FG線をSCREW にて締結" ], "WorkPoints": [ "一部を省いて描いています" ], "Tolks": [ "締付ﾄﾙｸ 80cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "80cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾊﾞｰ銘板貼付け", "WorkItems": [ "1. COVER のﾗﾍﾞﾙ貼付面の油分を除去", "2. COVER にLABEL LABEL LABEL を貼付け" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "30mm", "45mm" ] }

{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "60cN･m", "WorkName": "ｶﾊﾞｰ取付", "WorkItems": [ "■1. ①に②をSCREW にて取付" ], "WorkPoints": [ "計8か所を仮固定後､締結する" ], "Tolks": [ "締付ﾄﾙｸ 60cN･m" ], "InspectionNo": "GWETJ-F013-002", "InspectionItems": [ "検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認" ], "WorkTypes": [], "Words": [ "■安全作業" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "60cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "付属品ﾊﾟｯｷﾝｸﾞ", "WorkItems": [ "1. SPRING SPRING(BLACK) CLAMP-ARM(BLACK) FILTER TUBE (70MM CUT) をﾊﾟｯｷﾝｸﾞして､付属品とする" ], "WorkPoints": [ "付属品はﾊﾟｯｷﾝｸﾞして､ﾍｯﾄﾞ完成品と合わせて払い出す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "付属品", "合わせて払い出す" ] }

{ "QualityItem": "付属品確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示した付属品を払い出す事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "油砥石", "Size": "", "ToolOther": "", "WorkName": "ｶﾑﾌｫﾛｱ部組立", "WorkItems": [ "1. BRACKET の取付面(青色部)に砥石を掛ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }

{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "打痕、ﾊﾞﾘ無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "5.5㎜(BOX)", "ToolOther": "150cN･m", "WorkName": "ｶﾑﾌｫﾛｱ部組立", "WorkItems": [ "2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｱﾙﾐ用砥石", "Size": "", "ToolOther": "ｽｰﾊﾟｰｼｬｲﾅｰ砥石", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "表面" ] }

{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "打痕、ﾊﾞﾘ無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "表面" ] }

{ "QualityItem": "平面度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "0.1㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5626", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①", "WorkItems": [ "2. ①にBRACKET WASHER をBOLT で取付ける", "1. BRACKET に㉖油砥石を掛ける" ], "WorkPoints": [ "BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事", "①とBRACKET の間にWASHER を挿入する事", "BRACKET を㉗の青点線部に押し当てて取付ける事", "青色部に㉖を掛ける" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "FM-5626", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "250cN･m", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①", "WorkItems": [ "2. ①にBRACKET WASHER をBOLT で取付ける", "1. BRACKET に㉖油砥石を掛ける" ], "WorkPoints": [ "BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事", "①とBRACKET の間にWASHER を挿入する事", "BRACKET を㉗の青点線部に押し当てて取付ける事", "青色部に㉖を掛ける" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5626", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②", "WorkItems": [ "1. ①に②をBOLT で取付ける" ], "WorkPoints": [ "②を㉖の青点線部に押し当てて取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "FM-5626", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "250cN･m", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②", "WorkItems": [ "1. ①に②をBOLT で取付ける" ], "WorkPoints": [ "②を㉖の青点線部に押し当てて取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "油砥石", "Size": "", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③", "WorkItems": [ "2. ①にBLOCK をBOLT で取付ける", "1. BLOCK に㉖油砥石を掛ける" ], "WorkPoints": [ "BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事", "青色部に㉖を掛ける（面取りが無い側）", "BLOCK の面取り位置を図左手前にして取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "打痕、ﾊﾞﾘ無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5626", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③", "WorkItems": [ "2. ①にBLOCK をBOLT で取付ける", "1. BLOCK に㉖油砥石を掛ける" ], "WorkPoints": [ "BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事", "青色部に㉖を掛ける（面取りが無い側）", "BLOCK の面取り位置を図左手前にして取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "FM-5626", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "250cN･m", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③", "WorkItems": [ "2. ①にBLOCK をBOLT で取付ける", "1. BLOCK に㉖油砥石を掛ける" ], "WorkPoints": [ "BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事", "青色部に㉖を掛ける（面取りが無い側）", "BLOCK の面取り位置を図左手前にして取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "250cN･m", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④", "WorkItems": [ "1. ①にGUIDE をBOLT WASHER NUT で取付ける" ], "WorkPoints": [ "GUIDE は各々外側(矢印方向)に寄せて取付ける事(傾き無き事)" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "交換台車支持部(右)1", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "PIN出代:4㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "13㎜BOX", "ToolOther": "12.7N･m", "WorkName": "交換台車支持部(右)1", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "12.7N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "26.5N･m", "WorkName": "交換台車支持部(右)2", "WorkItems": [ "1. ①にCAM-FOLLOWER を取付ける" ], "WorkPoints": [ "付属ﾅｯﾄ" ], "Tolks": [ "締付ﾄﾙｸ 26.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "26.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.5N･m", "WorkName": "交換台車支持部(右)2", "WorkItems": [ "2. 1完成品にGUIDE をSPACER BOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "当付け方向" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "20N･m", "WorkName": "交換台車支持部(右)3", "WorkItems": [ "1. FRAME(R) に①BLOCK をBOLT で取付ける" ], "WorkPoints": [ "当付け方向", "当付け方向", "17/34連+17/34連仕様の取付け位置", "17/34連 + ﾄﾚｲ仕様の取付け位置" ], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "20N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "交換台車支持部(右)4", "WorkItems": [ "1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "面位置", "矢印方向に押し当てて取付ける" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "5.3N･m", "WorkName": "交換台車支持部(右)4", "WorkItems": [ "2. 1完成品をBRACKET にBOLT WASHER BOLT ㉒で取付ける" ], "WorkPoints": [ "長穴ｾﾝﾀｰに合せる", "前側取付位置", "後側取付位置" ], "Tolks": [ "締付ﾄﾙｸ 5.3N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "5.3N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "交換台車支持部(右)5", "WorkItems": [ "1. ①にCOVER をBOLT WASHER で取付ける" ], "WorkPoints": [ "ﾄﾚｲ仕様", "台車仕様", "ﾄﾚｲ仕様", "台車仕様" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "前側取付位置", "後側取付位置" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "6.0N･m", "WorkName": "交換台車支持部(右)6", "WorkItems": [ "1. ①に②をBOLT WASHER で取付ける" ], "WorkPoints": [ "面位置合せ" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "20N･m", "WorkName": "交換台車支持部(右)7", "WorkItems": [ "1. ①にBRACKET をBOLT WASHER で取付ける", "2. 1完成品にCOVER をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "20N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "交換台車支持部(右)7", "WorkItems": [ "1. ①にBRACKET をBOLT WASHER で取付ける", "2. 1完成品にCOVER をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(前側&右側)1", "WorkItems": [ "1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "平行に取付の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(前側&右側)2", "WorkItems": [ "1. ①にBRACKET をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾙｰ部品30連/60連(前側&右側)", "WorkItems": [ "1. H1工程へ払い出す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "部品準備", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示した部品を払い出す事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)1", "WorkItems": [ "1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "平行に取付の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)2", "WorkItems": [], "WorkPoints": [ "面位置に取付の事", "平行に取付の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "8㎜" ] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "各194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)2", "WorkItems": [], "WorkPoints": [ "面位置に取付の事", "平行に取付の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "8㎜" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法8.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾙｰ部品30連/60連(後側&右側)", "WorkItems": [ "1. PLUG を払い出す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "部品準備", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示した部品を払い出す事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｶﾑﾌｫﾛｱ部組立", "WorkItems": [ "1. BRACKET の取付面(黄色部)に砥石を掛ける", "2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける" ], "WorkPoints": [ "CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい", "この作業では同じものを4個製作" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "油砥石", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "5.5㎜(BOX)", "ToolOther": "150cN･m", "WorkName": "ｶﾑﾌｫﾛｱ部組立", "WorkItems": [ "2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける" ], "WorkPoints": [ "CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備", "WorkItems": [ "2. PLATE の平面度を測定する", "1. PLATE の両面に㉖を掛ける" ], "WorkPoints": [ "表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事", "PLATE に打痕やﾊﾞﾘが無い事", "緑色部の9箇所を測定する事(平面度:0.1㎜以内)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "表面", "裏面", "この作業では同じものを2個製作" ] }

{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "ｱﾙﾐ用砥石", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備", "WorkItems": [ "1. PLATE の両面に㉖を掛ける" ], "WorkPoints": [ "表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事", "PLATE に打痕やﾊﾞﾘが無い事", "緑色部の9箇所を測定する事(平面度:0.1㎜以内)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "表面", "この作業では同じものを2個製作" ] }

{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "0.1㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①", "WorkItems": [ "1. GUIDE に㉖油砥石を掛ける", "2. ①にGUIDE をBOLT で取付ける" ], "WorkPoints": [ "GUIDE を㉗に押し当てて取付ける事", "黄色部に㉖を掛ける", "GUIDE の全面にﾊﾞﾘ､打痕等ないか確認する事", "①の座ｸﾞﾘ面が無い方面に取付ける事", "㉗ナットの向きに注意してピンを①まで挿入して取付ける", "座ぐり穴の所にBOLT を入れる" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }

{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "油砥石", "ProcessNames": [] }

information_extraction

0

null