input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM502】を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SPACER :4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認",
"YMM502",
"ｽﾄｯﾊﾟｰ､固定子ｶﾊﾞｰと干渉無い事",
"ｽﾄｯﾊﾟｰ",
"固定子ｶﾊﾞｰ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理3",
"WorkItems": [
"1. ｴﾝｺｰﾀﾞ配線【YEM502】をﾌﾞﾗｹｯﾄに接続する",
"2. 【YMM506】【YEM506】【YMM502】【YEM502】を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"YEM502",
"面取り側を左に向け取付ける事",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"上へ向く様に引き回しする事"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける",
"1. ①をSCREW BOLT WASHER BOLT で取付ける",
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける",
"1. ①をSCREW BOLT WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける",
"1. ①をSCREW BOLT WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.8N･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける",
"1. ①をSCREW BOLT WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "6",
"ToolOther": "100cN･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける",
"1. ①をSCREW BOLT WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理",
"WorkItems": [
"1. X軸ｹｰﾌﾞﾙﾍﾞｱ配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(300mm)",
"配線の余長吸収箇所",
"ﾍｯﾄﾞをX軸左側ﾒｶｽﾄに当てた時に干渉無い事",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B2工程前準備にてｾｯﾄ済み"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理1",
"WorkItems": [
"1. Y軸ｹｰﾌﾞﾙﾍﾞｱ配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"外側",
"外側",
"HFPWA",
"φ6",
"φ6",
"CN2K501",
"CNHF",
"HFPWA",
"CN2AK",
"CN2BK",
"CN2K303",
"φ8",
"φ8",
"K501",
"AK502",
"BK502",
"配線を分ける(断面A-A)",
"ｲﾝｼｭﾛｯｸの頭はM/C外側に向ける事",
"7本",
"7本",
"8箇所",
"6箇所",
"ﾌﾞﾗｹｯﾄと干渉無い事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理2",
"WorkItems": [
"1. ﾍﾞｱ配管を接続し､ﾍﾞｱ配線を固定する",
"2. 架台に配線を引き回し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"配線を架台の開口部に入れる",
"ﾌﾛﾝﾄ",
"CNP3K501CNP3AK502CNP3BK502",
"CN2K501CN2AK502CN2BK502CN2K303CNHFHFPWA11",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｼﾞｮｲﾝﾄの位置に合わせて配管をｶｯﾄする",
"白配管【701L】",
"白配管【702L】",
"黄配管【301】",
"黒配管【201L】"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理3",
"WorkItems": [
"1. 架台に配線を引き回し固定する",
"2. 架台に配線を引き回し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"CN2K501CN2AK502CN2BK502CN2K303CNHFHFPWA11",
"ﾘｱへCNHFHFPWA11",
"ﾄﾞﾗｲﾊﾞへCN2K501CN2AK502CN2BK502",
"CPUへCN2K303CN4K303",
"ﾘｱよりCNP4K303",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(300mm)",
"M/C内部へ",
"配管に共締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理4",
"WorkItems": [
"1. 架台に配線を引き回し固定する",
"■2. XY軸ﾄﾞﾗｲﾊﾞｰに配線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理5",
"WorkItems": [
"■1. CPU BOXに配線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:5.CPU BOX-ｺﾈｸﾀ接続確認(1)ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"CN2K303",
"CN4K303",
"検査表①:5.CPC BOX-ｺﾈｸﾀ接続確認(2)ﾈｼﾞ締めﾄﾙｸ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN2K303とCN4K303のｹｰﾌﾞﾙを左右に遠ざけて整線する事",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理5",
"WorkItems": [
"■1. CPU BOXに配線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:5.CPC BOX-ｺﾈｸﾀ接続確認(2)ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"CN2K303",
"CN4K303",
"検査表①:5.CPU BOX-ｺﾈｸﾀ接続確認(1)ｺﾈｸﾀ接続確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN2K303とCN4K303のｹｰﾌﾞﾙを左右に遠ざけて整線する事",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽﾁｭｰﾌﾞ取付",
"WorkItems": [
"1. ｸﾞﾘｰｽﾁｭｰﾌﾞを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"正面図(ﾌﾛﾝﾄ)",
"A部",
"B部",
"左→手前",
"B部",
"右→奥",
"左→奥",
"右→手前",
"A部"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "圧入台",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾘﾆｱｽｹｰﾙ取付(左側)",
"WorkItems": [
"1. 架台へ①をBOLT で取付ける"
],
"WorkPoints": [
"①を取付ける際は､2名作業を徹底する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下に押し当て隙間無い事",
"左右位置:固定穴ｾﾝﾀｰ",
"ﾌﾛﾝﾄ",
"A矢視",
"A矢視図"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:8.Y軸ﾘﾆｱｽｹｰﾙの取付･調整",
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"配線向き",
"取付け穴のｾﾝﾀｰ合わせ",
"配線向き",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"㉙（0.4mm）を挟み隙間を調整し、㉘㉚（0.3mm/0.5mm）で隙間を確認する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.3",
"Size": "",
"ToolOther": "FM-2968",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
"検査表①:8.Y軸ﾘﾆｱｽｹｰﾙの取付･調整"
],
"WorkTypes": [],
"Words": [
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"配線向き",
"取付け穴のｾﾝﾀｰ合わせ",
"配線向き",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"㉙（0.4mm）を挟み隙間を調整し、㉘㉚（0.3mm/0.5mm）で隙間を確認する"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.4",
"Size": "",
"ToolOther": "FM-2707",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:8.Y軸ﾘﾆｱｽｹｰﾙの取付･調整",
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"配線向き",
"取付け穴のｾﾝﾀｰ合わせ",
"配線向き",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"㉙（0.4mm）を挟み隙間を調整し、㉘㉚（0.3mm/0.5mm）で隙間を確認する"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.5",
"Size": "",
"ToolOther": "FM-2969",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:8.Y軸ﾘﾆｱｽｹｰﾙの取付･調整",
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"配線向き",
"取付け穴のｾﾝﾀｰ合わせ",
"配線向き",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"㉙（0.4mm）を挟み隙間を調整し、㉘㉚（0.3mm/0.5mm）で隙間を確認する"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付2",
"WorkItems": [
"1. リニアスケールヘッドのコネクタを接続し、㉖㉗で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"YEM502",
"YEM506",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"配線を上に向ける事",
"配線を上に向ける事",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｵｲﾙ受けｶﾊﾞｰ取付",
"WorkItems": [
"1. COVER をWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "部品落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. COVER をBOLT WASHER で取付ける",
"2. ﾏﾙﾁｶﾒﾗ配線のﾏｳﾝﾄ(FT11)を差込む"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"差込む",
"ﾏﾙﾁｶﾒﾗ配線1A122A12",
"ﾌﾛﾝﾄ",
"正面図",
"ﾌﾞﾗｹｯﾄと厚肉の間にCOVER を差込む"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "ｶﾊﾞｰ取付",
"WorkItems": [
"1. 本体へCOVER をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｾｯﾄﾋﾞｽ出代調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6634",
"WorkName": "ｽﾍﾟｰｻｰ取付",
"WorkItems": [
"1. SPACER へSCREW を挿入する",
"3. 1の完成品と2の完成品を本体へ取付ける",
"2. SPACER へ㉖をセットし、SCREW を挿入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"SCREW が突き当たるまで挿入する事",
"この作業では同じものを2個製作",
"㉖がSPACER へ当たるまで挿入する事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6634",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "10.0N･m",
"WorkName": "ｽﾍﾟｰｻｰ取付",
"WorkItems": [],
"WorkPoints": [
"本体取付時に都度作成する事"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"左側面",
"右側面",
"SCREW が㉖へ当たるまで挿入する事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｸﾞﾘｰｽ封入",
"WorkItems": [
"2. Y軸ストッパー治具（FM-6365）を取り外し、㉗を取付ける",
"◆1. XY軸のグリースニップルから㉖を封入する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ(8箇所)/ﾘｱ(8箇所)行う事",
"配管が満たされるまで給脂する事(目視確認)",
"F/RのX軸を近づけ、㉗が動作する（ブザーが鳴る）事を確認する事",
"はみ出したｸﾞﾘｰｽは拭き取る事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
"検査表①:17.XY軸ｸﾞﾘｰｽ封入確認"
],
"WorkTypes": [],
"Words": [
"封入箇所③④",
"封入箇所①②",
"封入箇所⑤⑥",
"封入箇所⑦⑧",
"FM-6365",
"Xﾋﾞｰﾑﾌﾞﾗｹｯﾄ下面にSﾋﾟﾝを押し当てる事",
"ﾌﾛﾝﾄX軸",
"WETE-G002-C02"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配管が満たされるまで給脂はみ出し無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸二人作業用ｾﾝｻｰｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6693",
"WorkName": "XY軸ｸﾞﾘｰｽ封入",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"封入箇所③④",
"封入箇所⑦⑧",
"FM-6365",
"◆作業者安全作業",
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6693",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載①",
"WorkItems": [
"◆1. 本体へ①or②を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"or",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載①",
"WorkItems": [
"◆1. 本体へ①or②を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"or",
"or"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [
"2. ㉖を取り外す",
"1. ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰをBOLT BOLT BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)",
"締結が完了するまで㉖は外さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"検査表①:ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認",
"押し付け",
"押し付け",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(A,B,Cの3箇所)",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"押し付け",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"押し付け",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載③",
"WorkItems": [
"1. ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰをBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載①",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( A C E G I K )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾊﾞﾙﾌﾞ名称R4215",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載①",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( A C E G I K )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾊﾞﾙﾌﾞ名称R4215",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載①",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( A C E G I K )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾊﾞﾙﾌﾞ名称R4215",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載①",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( A C E G I K )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾊﾞﾙﾌﾞ名称R4215",
"搭載順序",
"or",
"◆作業者安全作業",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( B D F H J L )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4715",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( B D F H J L )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4715",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( B D F H J L )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4715",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( B D F H J L )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4715",
"搭載順序",
"or",
"◆作業者安全作業",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載①",
"WorkItems": [
"◆1. 本体へ①を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載①",
"WorkItems": [
"◆1. 本体へ①を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [
"1. ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰをBOLT BOLT で取付ける",
"2. ㉖を取り外す"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)",
"締結が完了するまで㉖は外さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認",
"ﾘｱ",
"押し付け",
"押し付け",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(A,B,Cの3箇所)",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [
"1. ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰをBOLT BOLT で取付ける",
"2. ㉖を取り外す"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)",
"締結が完了するまで㉖は外さ無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認",
"BOLT M6×20WASHER 厚肉座金",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [
"1. ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰをBOLT BOLT で取付ける",
"2. ㉖を取り外す"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)",
"締結が完了するまで㉖は外さ無い事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認"
],
"WorkTypes": [],
"Words": [
"BOLT M6×20WASHER 厚肉座金",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載③",
"WorkItems": [
"1. ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰをBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載①",
"WorkItems": [
"1. ①から延長ﾌﾟﾚｰﾄを取り外す"
],
"WorkPoints": [
"取り外した箇所に戻す為､元の取付け箇所が分かる様にしておく事(ﾈｼﾞも同様)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"延長ﾌﾟﾚｰﾄ",
"延長ﾌﾟﾚｰﾄ"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCDEF)",
"二人作業",
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4212",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"搭載順序",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4852",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCDEF)",
"二人作業",
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4212",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"搭載順序",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4852",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCDEF)",
"二人作業",
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4212",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"搭載順序",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCDEF)",
"二人作業",
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認"
],
"WorkTypes": [],
"Words": [
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"搭載順序",
"◆作業者安全作業",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載③",
"WorkItems": [
"1. 延長ﾌﾟﾚｰﾄを取付ける"
],
"WorkPoints": [
"元の取付け箇所に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"延長ﾌﾟﾚｰﾄ",
"延長ﾌﾟﾚｰﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "190cN･m",
"WorkName": "ﾍｯﾄﾞｶﾊﾞｰ取付",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 190cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "190cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞｰﾘﾌﾄ部吊上げｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5769",
"WorkName": "ﾘﾌﾄ部ﾒｲﾝﾌﾚｰﾑ取付",
"WorkItems": [
"◆1. ①に②をBOLT BOLT で取付",
"2. 1完成品に③④をBOLT WASHER で取付"
],
"WorkPoints": [
"大FRAMEはD-pinに挿入",
"二人作業で実施",
"小FRAMEはD-pin当付け",
"左右ﾌﾞﾗｹｯﾄが同じ高さになる位置に取付",
"t=0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾘﾌﾄ部の取付確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5769",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞｰ_ﾍﾞｰｽ吊上げｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5767",
"WorkName": "ﾘﾌﾄ部ﾒｲﾝﾌﾚｰﾑ取付",
"WorkItems": [
"◆1. ①に②をBOLT BOLT で取付",
"2. 1完成品に③④をBOLT WASHER で取付"
],
"WorkPoints": [
"大FRAMEはD-pinに挿入",
"二人作業で実施",
"小FRAMEはD-pin当付け",
"左右ﾌﾞﾗｹｯﾄが同じ高さになる位置に取付",
"t=0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾘﾌﾄ部の取付確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5767",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾌﾄ部ﾒｲﾝﾌﾚｰﾑ取付",
"WorkItems": [
"◆1. ①に②をBOLT BOLT で取付",
"2. 1完成品に③④をBOLT WASHER で取付"
],
"WorkPoints": [
"大FRAMEはD-pinに挿入",
"二人作業で実施",
"小FRAMEはD-pin当付け",
"左右ﾌﾞﾗｹｯﾄが同じ高さになる位置に取付",
"t=0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾘﾌﾄ部の取付確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ﾘﾌﾄ部ﾒｲﾝﾌﾚｰﾑ取付",
"WorkItems": [
"◆1. ①に②をBOLT BOLT で取付",
"2. 1完成品に③④をBOLT WASHER で取付"
],
"WorkPoints": [
"二人作業で実施",
"小FRAMEはD-pin当付け"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾘﾌﾄ部の取付確認",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾘﾌﾄ部ﾒｲﾝﾌﾚｰﾑ取付",
"WorkItems": [
"◆1. ①に②をBOLT BOLT で取付",
"2. 1完成品に③④をBOLT WASHER で取付"
],
"WorkPoints": [
"二人作業で実施",
"小FRAMEはD-pin当付け"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:ﾘﾌﾄ部の取付確認"
],
"WorkTypes": [],
"Words": [
"◆作業者安全作業",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾘﾌﾄ部ﾒｲﾝﾌﾚｰﾑ取付",
"WorkItems": [],
"WorkPoints": [
"大FRAMEはD-pinに挿入",
"左右ﾌﾞﾗｹｯﾄが同じ高さになる位置に取付",
"t=0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付",
"WorkItems": [
"■1. ⑤にLABEL を貼付ける"
],
"WorkPoints": [
"ｱﾙｺｰﾙ使用時には保護ﾒｶﾞﾈを着用の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"20㎜",
"面位置",
"検査表LABEL :TLﾓｰﾀｰの高温注意ﾗﾍﾞﾙ貼付け確認",
"■安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付",
"WorkItems": [
"■1. ⑤にLABEL を貼付ける"
],
"WorkPoints": [
"ｱﾙｺｰﾙ使用時には保護ﾒｶﾞﾈを着用の事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表LABEL :TLﾓｰﾀｰの高温注意ﾗﾍﾞﾙ貼付け確認"
],
"WorkTypes": [],
"Words": [
"20㎜",
"面位置",
"WETE-G002-A011"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り貼付られている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾘﾌﾄ部上下動作用治具取付",
"WorkItems": [
"1. ①に㉖を取付",
"2. 1完成品に㉙を接続しスイッチを入れる"
],
"WorkPoints": [
"取付後ﾊﾝﾄﾞﾙを回しﾛｯｸされてることを確認する(ﾊﾝﾄﾞﾙは回りません)",
"M6固定ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾘﾌﾄ部上下動作用治具取付",
"WorkItems": [],
"WorkPoints": [
"六角支柱が下穴に正常に入っている事",
"ﾎﾞﾙﾄ緩み無き事",
"100V電源を差込み､ﾓｰﾀからの\"ILB401P\"を接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｸﾞﾘｰｽ飛散防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER (上側)､BOLT WASHER (下側)で取付"
],
"WorkPoints": [
"断面(上面より)",
"②の取付時､矢印方向へ押して固定する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上と下のﾎﾞﾙﾄを締めながら取付き状態を確認し固定する",
"ｶﾊﾞｰとﾎﾙﾀﾞｰの隙間を確認し干渉が無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｸﾞﾘｰｽ飛散防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER (上側)､BOLT WASHER (下側)で取付"
],
"WorkPoints": [
"断面(上面より)",
"②の取付時､矢印方向へ押して固定する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上と下のﾎﾞﾙﾄを締めながら取付き状態を確認し固定する",
"ｶﾊﾞｰとﾎﾙﾀﾞｰの隙間を確認し干渉が無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｸﾞﾘｰｽ飛散防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER (上側)､BOLT WASHER (下側)で取付"
],
"WorkPoints": [
"断面(上面より)",
"②の取付時､矢印方向へ押して固定する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上と下のﾎﾞﾙﾄを締めながら取付き状態を確認し固定する",
"ｶﾊﾞｰとﾎﾙﾀﾞｰの隙間を確認し干渉が無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き出部取付",
"WorkItems": [
"◆1. ①に②をBOLT WASHER で仮取付",
"2. 仮水準を出す"
],
"WorkPoints": [
"二人作業で実施",
"3本の偏芯ﾋﾟﾝで調整",
"LMｶﾞｲﾄﾞ固定ﾈｼﾞの上から3個目が見える位置で行う事",
"規格値:2目盛り以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉗配置",
"固定PIN",
"偏芯PIN",
"偏芯PIN",
"仮止め:SD-A051313-111にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "引き出部取付",
"WorkItems": [
"2. 仮水準を出す"
],
"WorkPoints": [
"3本の偏芯ﾋﾟﾝで調整",
"規格値:2目盛り以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉗配置",
"固定PIN",
"偏芯PIN",
"偏芯PIN",
"◆作業者安全作業"
]
} | {
"QualityItem": "水準確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2目盛り以内",
"Method": "水準器",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "平面調整治具",
"Size": "",
"ToolOther": "FM-5040",
"WorkName": "引き出部取付",
"WorkItems": [
"2. 仮水準を出す"
],
"WorkPoints": [
"3本の偏芯ﾋﾟﾝで調整",
"規格値:2目盛り以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉗配置",
"固定PIN",
"偏芯PIN",
"偏芯PIN",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5040",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ｻﾌﾞﾌﾚｰﾑ取付",
"WorkItems": [
"1. ①に②をBOLT BOLT で取付"
],
"WorkPoints": [
"当付け面",
"t=0.1㎜が通ら無い事",
"ﾌﾚｰﾑとﾍﾞｰｽｻﾞｸﾞﾘ面に5㎜のﾌﾞﾛｯｸｹﾞｰｼﾞが入る事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾘﾌﾄ部の取付確認",
"5㎜",
"5㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾚｰﾑ取付",
"WorkItems": [
"1. ①に②をBOLT BOLT で取付"
],
"WorkPoints": [
"当付け面",
"t=0.1㎜が通ら無い事",
"ﾌﾚｰﾑとﾍﾞｰｽｻﾞｸﾞﾘ面に5㎜のﾌﾞﾛｯｸｹﾞｰｼﾞが入る事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾘﾌﾄ部の取付確認",
"5㎜",
"5㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾚｰﾑ取付",
"WorkItems": [
"1. ①に②をBOLT BOLT で取付"
],
"WorkPoints": [
"当付け面",
"t=0.1㎜が通ら無い事",
"ﾌﾚｰﾑとﾍﾞｰｽｻﾞｸﾞﾘ面に5㎜のﾌﾞﾛｯｸｹﾞｰｼﾞが入る事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:ﾘﾌﾄ部の取付確認"
],
"WorkTypes": [],
"Words": [
"5㎜",
"5㎜",
"WETE-G002-A011"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾌﾄ部吸着側取付①",
"WorkItems": [
"1. ①に②をBOLT BOLT で仮取付"
],
"WorkPoints": [
"ﾘﾌﾄ部(ﾏｶﾞｼﾞﾝ側)のDpinに合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A051313-108にて本締め",
"D-pin",
"D-pin"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾘﾌﾄ部吸着側取付②",
"WorkItems": [
"1. ①の取付部の隙間､傾きを確認し固定する"
],
"WorkPoints": [
"隙間発生の場合､引き出部との間隔を確認､ｻﾌﾞﾌﾚｰﾑの取付位置を確認問題なければそのまま締付",
"･吸着部よりｻﾌﾞﾌﾚｰﾑが内側にある場合､ｻﾌﾞﾌﾚｰﾑを外側に押しながらﾎﾞﾙﾄを挿入する｡･吸着部とｻﾌﾞﾌﾚｰﾑの段差が無い状態か､ｻﾌﾞﾌﾚｰﾑが出ている場合､上下同じ出代に調整し固定する｡",
"吸着部とｻﾌﾞﾌﾚｰﾑの隙間(A矢視図)",
"吸着部とｻﾌﾞﾌﾚｰﾑの傾き(B矢視図)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｶﾊﾞｰﾌﾟﾚｰﾄの取付確認",
"A矢視",
"B矢視"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾘﾌﾄ部吸着側取付②",
"WorkItems": [
"1. ①の取付部の隙間､傾きを確認し固定する"
],
"WorkPoints": [
"隙間発生の場合､引き出部との間隔を確認､ｻﾌﾞﾌﾚｰﾑの取付位置を確認問題なければそのまま締付",
"･吸着部よりｻﾌﾞﾌﾚｰﾑが内側にある場合､ｻﾌﾞﾌﾚｰﾑを外側に押しながらﾎﾞﾙﾄを挿入する｡･吸着部とｻﾌﾞﾌﾚｰﾑの段差が無い状態か､ｻﾌﾞﾌﾚｰﾑが出ている場合､上下同じ出代に調整し固定する｡",
"吸着部とｻﾌﾞﾌﾚｰﾑの隙間(A矢視図)",
"吸着部とｻﾌﾞﾌﾚｰﾑの傾き(B矢視図)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｶﾊﾞｰﾌﾟﾚｰﾄの取付確認",
"A矢視",
"B矢視"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾌﾄ部吸着側取付②",
"WorkItems": [
"1. ①の取付部の隙間､傾きを確認し固定する"
],
"WorkPoints": [
"隙間発生の場合､引き出部との間隔を確認､ｻﾌﾞﾌﾚｰﾑの取付位置を確認問題なければそのまま締付",
"･吸着部よりｻﾌﾞﾌﾚｰﾑが内側にある場合､ｻﾌﾞﾌﾚｰﾑを外側に押しながらﾎﾞﾙﾄを挿入する｡･吸着部とｻﾌﾞﾌﾚｰﾑの段差が無い状態か､ｻﾌﾞﾌﾚｰﾑが出ている場合､上下同じ出代に調整し固定する｡",
"吸着部とｻﾌﾞﾌﾚｰﾑの隙間(A矢視図)",
"吸着部とｻﾌﾞﾌﾚｰﾑの傾き(B矢視図)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:ｶﾊﾞｰﾌﾟﾚｰﾄの取付確認"
],
"WorkTypes": [],
"Words": [
"A矢視",
"B矢視",
"WETE-G002-A011"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "ﾚﾍﾞﾙ出し調整",
"WorkItems": [
"1. ①のﾚﾍﾞﾙ出しを行う"
],
"WorkPoints": [
"規格値:0.03㎜/m以内",
"ｷｬｽﾀｰでﾚﾍﾞﾙ出しの事",
"完成までﾚﾍﾞﾙが変化しない様､ｱｼﾞｬｽﾄﾎﾞﾙﾄで仮固定の事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:ﾌﾚｰﾑのﾚﾍﾞﾙ確認"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A011"
]
} | {
"QualityItem": "水準確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜/m以内以下",
"Method": "水準器",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "引き出部位置決め",
"WorkItems": [
"1. ①の仮固定ﾎﾞﾙﾄを緩める",
"2. ㉗をセットし､位置出し調整を行う"
],
"WorkPoints": [
"➡は治具方向 ➡は引き出し部方向",
"作業者側",
"吸着側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A051313-111にて本締め",
"検査表①:引き出し部取付調整後の隙間確認",
"検査表①:ﾊﾟﾚｯﾄｶﾞｲﾄﾞの確認"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "引き出部位置決め",
"WorkItems": [
"1. ①の仮固定ﾎﾞﾙﾄを緩める",
"2. ㉗をセットし､位置出し調整を行う"
],
"WorkPoints": [
"➡は治具方向 ➡は引き出し部方向",
"作業者側",
"吸着側"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:引き出し部取付調整後の隙間確認"
],
"WorkTypes": [],
"Words": [
"仮止め:SD-A051313-111にて本締め",
"検査表①:ﾊﾟﾚｯﾄｶﾞｲﾄﾞの確認",
"WETE-G002-A011"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜以下が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "引き出部位置決め",
"WorkItems": [
"1. ①の仮固定ﾎﾞﾙﾄを緩める",
"2. ㉗をセットし､位置出し調整を行う"
],
"WorkPoints": [
"➡は治具方向 ➡は引き出し部方向",
"作業者側",
"吸着側"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:ﾊﾟﾚｯﾄｶﾞｲﾄﾞの確認"
],
"WorkTypes": [],
"Words": [
"仮止め:SD-A051313-111にて本締め",
"検査表①:引き出し部取付調整後の隙間確認",
"WETE-G002-A011"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜以下が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "2.0㎜",
"ToolOther": "",
"WorkName": "引き出部位置決め",
"WorkItems": [
"1. ①の仮固定ﾎﾞﾙﾄを緩める",
"2. ㉗をセットし､位置出し調整を行う"
],
"WorkPoints": [
"➡は治具方向 ➡は引き出し部方向",
"作業者側",
"吸着側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A051313-111にて本締め",
"検査表①:引き出し部取付調整後の隙間確認",
"検査表①:ﾊﾟﾚｯﾄｶﾞｲﾄﾞの確認"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付できている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "引き出部水準出し",
"WorkItems": [
"2. 最終水準出し調整･引き出部締結",
"1. ①に㉗をセットし㉖を置く",
"3. 引き出部の固定ﾎﾞﾙﾄの増し締め",
"2. 最終水準出し調整･引き出部締結",
"1. ①に㉗をセットし㉖を置く",
"3. 引き出部の固定ﾎﾞﾙﾄの増し締め"
],
"WorkPoints": [
"X･Y方向: 0.1mm/m以内",
"1.偏芯PIN 3本を右に回し水準を出す2.偏芯PINを動かさずにﾅｯﾄ側で締め付ける",
"作業者側",
"X･Y方向: 0.1mm/m以内",
"1.偏芯PIN 3本を右に回し水準を出す2.偏芯PINを動かさずにﾅｯﾄ側で締め付ける",
"作業者側"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:引き出し部のﾚﾍﾞﾙ確認",
"検査表①:引き出し部のﾚﾍﾞﾙ確認"
],
"WorkTypes": [],
"Words": [
"後側面",
"偏芯PIN",
"後側面",
"固定PIN",
"固定ﾎﾞﾙﾄ",
"偏芯PIN",
"偏芯PIN",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"後側面",
"偏芯PIN",
"後側面",
"固定PIN",
"固定ﾎﾞﾙﾄ",
"偏芯PIN",
"偏芯PIN",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"WETE-G002-A011"
]
} | {
"QualityItem": "水準確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "X･Y方向0.1㎜/m以内",
"Method": "水準器",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "平面調整治具",
"Size": "",
"ToolOther": "FM-5040",
"WorkName": "引き出部水準出し",
"WorkItems": [
"2. 最終水準出し調整･引き出部締結",
"1. ①に㉗をセットし㉖を置く",
"3. 引き出部の固定ﾎﾞﾙﾄの増し締め",
"2. 最終水準出し調整･引き出部締結",
"1. ①に㉗をセットし㉖を置く",
"3. 引き出部の固定ﾎﾞﾙﾄの増し締め"
],
"WorkPoints": [
"X･Y方向: 0.1mm/m以内",
"1.偏芯PIN 3本を右に回し水準を出す2.偏芯PINを動かさずにﾅｯﾄ側で締め付ける",
"作業者側",
"X･Y方向: 0.1mm/m以内",
"1.偏芯PIN 3本を右に回し水準を出す2.偏芯PINを動かさずにﾅｯﾄ側で締め付ける",
"作業者側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後側面",
"偏芯PIN",
"後側面",
"固定PIN",
"固定ﾎﾞﾙﾄ",
"偏芯PIN",
"偏芯PIN",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"検査表①:引き出し部のﾚﾍﾞﾙ確認",
"後側面",
"偏芯PIN",
"後側面",
"固定PIN",
"固定ﾎﾞﾙﾄ",
"偏芯PIN",
"偏芯PIN",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"検査表①:引き出し部のﾚﾍﾞﾙ確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5040",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "引き出部水準出し",
"WorkItems": [
"2. 最終水準出し調整･引き出部締結",
"1. ①に㉗をセットし㉖を置く",
"3. 引き出部の固定ﾎﾞﾙﾄの増し締め"
],
"WorkPoints": [
"X･Y方向: 0.1mm/m以内",
"1.偏芯PIN 3本を右に回し水準を出す2.偏芯PINを動かさずにﾅｯﾄ側で締め付ける",
"作業者側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後側面",
"偏芯PIN",
"後側面",
"固定PIN",
"固定ﾎﾞﾙﾄ",
"偏芯PIN",
"偏芯PIN",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ",
"検査表①:引き出し部のﾚﾍﾞﾙ確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾞｲﾄﾞ幅調整治具",
"Size": "",
"ToolOther": "FM-5242",
"WorkName": "吸着部の左右搬送ｶﾞｲﾄﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [
"吸着部のｶﾞｲﾄﾞ全体が引き出部のｶﾞｲﾄﾞ高さより低いことを確認治具が吸着部へ落ち込んで無い事を確認する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部で吸着部を持ち上げ㉖を載せ吸着部へスライドさせる",
"検査表①:吸着部の左右ｶﾞｲﾄﾞ高さ確認",
"(7.5㎜)",
"検査表①:吸着部の左右ｶﾞｲﾄﾞ高さ確認",
"(7.5㎜)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5242",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "吸着部の左右搬送ｶﾞｲﾄﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:吸着部の左右ｶﾞｲﾄﾞ高さ確認",
"検査表①:吸着部の左右ｶﾞｲﾄﾞ高さ確認"
],
"WorkTypes": [],
"Words": [
"(7.5㎜)",
"(7.5㎜)",
"WETE-G002-A011"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "吸着部の左右搬送ｶﾞｲﾄﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:吸着部の左右ｶﾞｲﾄﾞ高さ確認",
"(7.5㎜)",
"検査表①:吸着部の左右ｶﾞｲﾄﾞ高さ確認",
"(7.5㎜)"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "吸着部の左右搬送ｶﾞｲﾄﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:吸着部の左右ｶﾞｲﾄﾞ高さ確認",
"(7.5㎜)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "吸着部の左右搬送ｶﾞｲﾄﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [
"吸着部のｶﾞｲﾄﾞ全体が引き出部のｶﾞｲﾄﾞ高さより低いことを確認治具が吸着部へ落ち込んで無い事を確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部で吸着部を持ち上げ㉖を載せ吸着部へスライドさせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "吸着部の左右搬送ｶﾞｲﾄﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [
"吸着部のｶﾞｲﾄﾞ全体が引き出部のｶﾞｲﾄﾞ高さより低いことを確認治具が吸着部へ落ち込んで無い事を確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部で吸着部を持ち上げ㉖を載せ吸着部へスライドさせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "吸着部の左右ｶﾞｲﾄﾞ幅調整",
"WorkItems": [
"1. 搬送ｶﾞｲﾄﾞﾌﾞﾗｹｯﾄの幅調整",
"2.吸着部ｶﾞｲﾄﾞの幅調整"
],
"WorkPoints": [
"引き出部を基準に吸着部のﾌﾞﾗｹｯﾄの外側を合わせる",
"引き出部",
"治具とｶﾞｲﾄﾞ隙間 0.1㎜が入らない様に調整し固定ｶﾞｲﾄﾞを固定する",
"固定ﾎﾞﾙﾄ",
"引き出部",
"目視で揃っていればOK"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "段差確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された寸法になっている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "吸着部の左右ｶﾞｲﾄﾞ幅調整",
"WorkItems": [],
"WorkPoints": [
"吸着部",
"吸着部"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:吸着部の左右ｶﾞｲﾄﾞ幅確認",
"引き出部搬送ｶﾞｲﾄﾞに㉙を載せて基準にし、吸着部へスライドさせて吸着部ガイドを合わせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾞｲﾄﾞ幅調整治具",
"Size": "",
"ToolOther": "FM-5242",
"WorkName": "吸着部の左右ｶﾞｲﾄﾞ幅調整",
"WorkItems": [],
"WorkPoints": [
"吸着部",
"吸着部"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:吸着部の左右ｶﾞｲﾄﾞ幅確認",
"引き出部搬送ｶﾞｲﾄﾞに㉙を載せて基準にし、吸着部へスライドさせて吸着部ガイドを合わせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5242",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "吸着部の左右ｶﾞｲﾄﾞ幅調整",
"WorkItems": [],
"WorkPoints": [
"吸着部",
"吸着部"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:吸着部の左右ｶﾞｲﾄﾞ幅確認"
],
"WorkTypes": [],
"Words": [
"引き出部搬送ｶﾞｲﾄﾞに㉙を載せて基準にし、吸着部へスライドさせて吸着部ガイドを合わせる",
"WETE-G002-A011"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｶﾞｲﾄﾞ隙間0.1㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "80cN･m",
"WorkName": "吸着部の左右ｶﾞｲﾄﾞ幅調整",
"WorkItems": [
"1. 搬送ｶﾞｲﾄﾞﾌﾞﾗｹｯﾄの幅調整",
"2.吸着部ｶﾞｲﾄﾞの幅調整"
],
"WorkPoints": [
"引き出部を基準に吸着部のﾌﾞﾗｹｯﾄの外側を合わせる",
"引き出部",
"治具とｶﾞｲﾄﾞ隙間 0.1㎜が入らない様に調整し固定ｶﾞｲﾄﾞを固定する",
"固定ﾎﾞﾙﾄ",
"引き出部",
"目視で揃っていればOK"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾞｲﾄﾞ幅調整治具",
"Size": "",
"ToolOther": "FM-5242",
"WorkName": "吸着部の中央部搬送ｶﾞｲﾄﾞ上下調整",
"WorkItems": [
"1. ①の吸着部内側ｶﾞｲﾄﾞ上に㉖の隙間調整治具を載せる",
"2. 吸着部の黄丸部分のボルトを緩め,ｶﾞｲﾄﾞ全体を㉖へ押し当て固定する",
"3.ｶﾞｲﾄﾞの高さ確認"
],
"WorkPoints": [
"押し当て過ぎると段差が発生するので注意する0.1mmが通り0.15mmが通らない様に調整する",
"測定後､治具ﾌﾟﾚｰﾄを引き出部から吸着部へｽﾗｲﾄﾞさせながら引っ掛かりが無い事を確認する同様の作業を左右共に行う事｡隙間が有った場合は再度調整する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"断面図(上図黄線)",
"㉗㉘",
"㉗㉘",
"㉖－1",
"㉖－2",
"ｼｯｸﾈｽｹﾞｰｼﾞで㉖の-1・-2のﾎﾟｲﾝﾄ測定、0.15㎜が入ら無い事を確認する",
"検査表①:吸着部の中央下側ｶﾞｲﾄﾞの高さ調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5242",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.15㎜",
"ToolOther": "",
"WorkName": "吸着部の中央部搬送ｶﾞｲﾄﾞ上下調整",
"WorkItems": [
"1. ①の吸着部内側ｶﾞｲﾄﾞ上に㉖の隙間調整治具を載せる",
"2. 吸着部の黄丸部分のボルトを緩め,ｶﾞｲﾄﾞ全体を㉖へ押し当て固定する",
"3.ｶﾞｲﾄﾞの高さ確認"
],
"WorkPoints": [
"押し当て過ぎると段差が発生するので注意する0.1mmが通り0.15mmが通らない様に調整する",
"測定後､治具ﾌﾟﾚｰﾄを引き出部から吸着部へｽﾗｲﾄﾞさせながら引っ掛かりが無い事を確認する同様の作業を左右共に行う事｡隙間が有った場合は再度調整する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "WETE-G002-A011",
"InspectionItems": [
"検査表①:吸着部の中央下側ｶﾞｲﾄﾞの高さ調整"
],
"WorkTypes": [],
"Words": [
"断面図(上図黄線)",
"㉗㉘",
"㉗㉘",
"㉖－1",
"㉖－2",
"ｼｯｸﾈｽｹﾞｰｼﾞで㉖の-1・-2のﾎﾟｲﾝﾄ測定、0.15㎜が入ら無い事を確認する",
"WETE-G002-A011"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜:通り0.15㎜:止り",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A011",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "吸着部の中央部搬送ｶﾞｲﾄﾞ上下調整",
"WorkItems": [],
"WorkPoints": [
"測定後､治具ﾌﾟﾚｰﾄを引き出部から吸着部へｽﾗｲﾄﾞさせながら引っ掛かりが無い事を確認する同様の作業を左右共に行う事｡隙間が有った場合は再度調整する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉗㉘",
"㉗㉘",
"㉖－1",
"㉖－2",
"ｼｯｸﾈｽｹﾞｰｼﾞで㉖の-1・-2のﾎﾟｲﾝﾄ測定、0.15㎜が入ら無い事を確認する",
"検査表①:吸着部の中央下側ｶﾞｲﾄﾞの高さ調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "防錆油",
"Size": "",
"ToolOther": "ｴﾊﾞｰｽ",
"WorkName": "防錆油・ｸﾞﾘｰｽ塗布",
"WorkItems": [
"◆1. ①の指示部に防錆油･ｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"LCG100",
"本体ﾌﾚｰﾑ周りの加工面全体に塗布する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ容器",
"*20㎜程度",
"ｴﾊﾞｰｽ",
"ｴﾊﾞｰｽ",
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り塗布してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｴﾊﾞｰｽ",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.