input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑥",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"A矢視は寸法の位置に従って取付の事",
"上面が定盤に当たっている状態で取付の事",
"B矢視",
"C矢視",
"D矢視"
],
"Tolks": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑦",
"WorkItems": [
"1. ①②にBRACKET BOLT を取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": ""... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑦",
"WorkItems": [
"1. ①②にBRACKET BOLT を取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": ""... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑧",
"WorkItems": [
"1. ①②にBRACKET BOLT を取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"B矢視",
"C矢視",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": ""... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑧",
"WorkItems": [
"1. ①②にBRACKET BOLT を取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"B矢視",
"C矢視",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": ""... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑨",
"WorkItems": [
"1. ①②に③をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"C矢視",
"D矢視",
"B矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑨",
"WorkItems": [
"1. ①②に③をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"C矢視",
"D矢視",
"B矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑨",
"WorkItems": [
"1. ①②に③をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"C矢視",
"D矢視",
"B矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"Insp... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑩",
"WorkItems": [
"1. ①②をBRACKET BRACKET BOLT で仮取付"
],
"WorkPoints": [
"A矢視",
"B矢視",
"A･B矢視の反対側も同様に仮取付する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wo... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑪",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視",
"A矢視は寸法の位置に従って取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"Inspe... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.10㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑪",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視",
"A矢視は寸法の位置に従って取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"Inspe... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑪",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視",
"A矢視は寸法の位置に従って取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｷｬｽﾀｰ部組立",
"WorkItems": [
"2. PLATE PLATE (4個)に1完成品(4個)を仮付けする",
"◆1. ADJUST-BOLT (4個)ﾎﾞﾙﾄﾈｼﾞ部にｸﾞﾘｰｽを塗布する",
"3. 2完成品にCASTER をNUT WASHER で取付ける"
],
"WorkPoints": [
"図の通り対称のものを2個作製する",
"対称のものを2個ずつ作製する",
"仮固定",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｸﾞﾘｰｽ容器10㎜程度",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｷｬｽﾀｰ部組立",
"WorkItems": [
"2. PLATE PLATE (4個)に1完成品(4個)を仮付けする",
"◆1. ADJUST-BOLT (4個)ﾎﾞﾙﾄﾈｼﾞ部にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"図の通り対称のものを2個作製する",
"他にｸﾞﾘｰｽが付かないように塗布する事"
],
"Tolks": [],
"InspectionNo": ""... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ｷｬｽﾀｰ部組立",
"WorkItems": [
"2. PLATE PLATE (4個)に1完成品(4個)を仮付けする",
"◆1. ADJUST-BOLT (4個)ﾎﾞﾙﾄﾈｼﾞ部にｸﾞﾘｰｽを塗布する",
"3. 2完成品にCASTER をNUT WASHER で取付ける"
],
"WorkPoints": [
"図の通り対称のものを2個作製する",
"対称のものを2個ずつ作製する",
"仮固定... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ｷｬｽﾀｰ部取付",
"WorkItems": [
"1. ①に②③(4個)をBOLT で取付ける"
],
"WorkPoints": [
"ｷｬｽﾀｰﾌﾟﾚｰﾄがﾌﾚｰﾑからはみ出さず面一で取付",
"②③の違い",
"K036-1",
"K036-2",
"②③の取付位置に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後貼付",
"ﾌﾞﾗｹｯﾄ右面から119±1㎜",
"ﾌﾞﾗｹｯﾄ上面から40±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後貼付",
"ﾌﾞﾗｹｯﾄ右面から119±1㎜",
"ﾌﾞﾗｹｯﾄ上面から40±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰ部組立",
"WorkItems": [
"1. REGULATOR の付属のｹﾞｰｼﾞの目盛を0.4~0.5に設定する",
"2. 1完成品をREGULATOR 本体に取付ける",
"3. 2完成品にCOUPLER とJOINT を取付ける"
],
"WorkPoints": [
"OUT側",
"出代41.5±1㎜",
"目視で平行にする",
"ｹﾞｰｼﾞの取付に... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. COVER の穴(2ヵ所)にBUSH を指定寸法にｶｯﾄし貼付ける",
"2. 1完成品に①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①の取付位置に注意する事",
"GEE144F-A-C (両面ﾃｰﾌﾟ付き)",
"出代46±1㎜"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [
"BUSH 120±1.0㎜",
"BUSH 25±1.0㎜×2"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰ組立",
"WorkItems": [
"1. REGULATOR 付属のｹﾞｰｼﾞをREGULATOR 本体に取付ける(2ｹ製作)"
],
"WorkPoints": [
"本体~ｹﾞｰｼﾞ端面15±1㎜の出代で取付ける(ｹﾞｰｼﾞの傾きも注意する)",
"JOINT の締付に注意する事",
"目視で平行になる様取付ける",
"付属のｹﾞｰｼﾞ取付向きに注意する事",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰ組立",
"WorkItems": [
"1. REGULATOR 付属のｹﾞｰｼﾞをREGULATOR 本体に取付ける(2ｹ製作)"
],
"WorkPoints": [
"本体~ｹﾞｰｼﾞ端面15±1㎜の出代で取付ける(ｹﾞｰｼﾞの傾きも注意する)",
"JOINT の締付に注意する事",
"目視で平行になる様取付ける",
"付属のｹﾞｰｼﾞ取付向きに注意する... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後指定銘板を貼付ける",
"ﾌﾞﾗｹｯﾄ上面から80±1㎜",
"ﾌﾞﾗｹｯﾄ下面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から15±1㎜"
],
"Tolks": [],
"Inspectio... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後指定銘板を貼付ける",
"ﾌﾞﾗｹｯﾄ上面から80±1㎜",
"ﾌﾞﾗｹｯﾄ下面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から15±1㎜"
],
"Tolks": [],
"Inspectio... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET に①を②で取付ける(2ヵ所)"
],
"WorkPoints": [
"目視で平行になる様取付ける",
"･①の傾きに注意する事･②の表裏に注意する事",
"内側",
"IN側",
"IN側",
"外側",
"ﾒｲﾝｴｱｰﾚｷﾞｭﾚｰﾀ"
],
"Tolks"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示位置にLABEL を貼付ける",
"ﾌﾞﾗｹｯﾄ下面から47±1㎜",
"ﾌﾞﾗｹｯﾄ左面から15±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示位置にLABEL を貼付ける",
"ﾌﾞﾗｹｯﾄ下面から47±1㎜",
"ﾌﾞﾗｹｯﾄ左面から15±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "42cN･m",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [
"SWITCH 付属品を使用し組立",
"SWITCH のﾌﾞﾗｹｯﾄの向きに注意する事",
"1完成品の向きに注意する事",
"BRACKET の向きに注意する事",
"付属ﾌﾞﾗｹｯﾄの向きに注意"
],
"Tolks": [
"締付ﾄﾙｸ 42cN･m",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "42cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [
"SW側を右向きで取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. SWITCH 付属のﾌﾞﾗｹｯﾄをSWITCH ﾌﾛｰSWへ付属のﾎﾞﾙﾄで取付ける(2ヵ所)",
"2. 1完成品をBRACKET BOLT WASHER で取付ける",
"3. 2完成品にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"Inspecti... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立(配線、配管接続)",
"WorkItems": [
"2. 1完成品を①に接続する",
"1. TUBE を指示寸法にｶｯﾄする",
"3. 2完成品にLABEL ﾀｸﾞ取付と負荷ﾗﾍﾞﾙ貼付を行う"
],
"WorkPoints": [
"L=200㎜ ×1L=1000㎜ ×1",
"200㎜",
"1B011R",
"1000㎜",
"30±... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜",
"ToolOther": "1.2N･m",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立",
"WorkItems": [
"1. AIR-BLOCK にCOUPLER PLUG JOINT 取付ける"
],
"WorkPoints": [
"COUPLER PLUG JOINT の取付に注意する",
"12±0.5㎜",
"1.0±0.5㎜",
"PLUG の締め込み量",
"JOINT の締め込み量",
"COUPLER 20ｹ取付ける"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立",
"WorkItems": [
"1. AIR-BLOCK にCOUPLER PLUG JOINT 取付ける"
],
"WorkPoints": [
"COUPLER PLUG JOINT の取付に注意する",
"12±0.5㎜",
"1.0±0.5㎜",
"PLUG の締め込み量",
"JOINT の締め込み量",
"COUPLER 20ｹ取付ける"
],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立(ｶﾞｲﾄﾞ取付)",
"WorkItems": [
"1. ①をBRACKET にBOLT WASHER で取付ける",
"2. 1完成品にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"①の向きに注意する事",
"切り欠き",
"折り曲げ",
"押し当てで取付ける",
"GUIDE の取付けに注意する事",
"押... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立(ｶﾞｲﾄﾞ取付)",
"WorkItems": [
"1. ①をBRACKET にBOLT WASHER で取付ける",
"2. 1完成品にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"①の向きに注意する事",
"切り欠き",
"折り曲げ",
"押し当てで取付ける",
"GUIDE の取付けに注意する事",
"押し... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立(ｻｲﾄﾞﾌﾟﾚｰﾄ取付)",
"WorkItems": [
"1. PLATE へ①SPACER をBOLT WASHER で仮止め"
],
"WorkPoints": [
"①の取付けに注意する事",
"ｶﾌﾟﾗ",
"折り曲げ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ下面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から75±1㎜",
"ﾌﾞﾗｹｯﾄ下面から30±1㎜",
"下記指示寸法位置に㉖㉗で脱脂後貼付ける"
],
"Tolks": [... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ下面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から75±1㎜",
"ﾌﾞﾗｹｯﾄ下面から30±1㎜",
"下記指示寸法位置に㉖㉗で脱脂後貼付ける"
],
"Tolks": [... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "60cN･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｺﾈｸﾀ取付)",
"WorkItems": [
"1. ①へCONNECTOR をSCREW で取付ける(20ｶ所)"
],
"WorkPoints": [
"CONNECTOR の取付けに注意する事",
"左に押し当てで固定する事",
"折り曲げ",
"写真の向きで取付ける",
"CONNECTOR の向きに注意し①の穴に入れ取付ける",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ﾋﾟﾝ取付)",
"WorkItems": [
"2. 1完成品を㉙治具にセットしピンの位置決めを行い固定する",
"▲1. ①へPIN をNUT で取付(20ｶ所)"
],
"WorkPoints": [
"全てﾋﾟﾝの溝が治具に入った事を確認し､全てのﾋﾟﾝを規定ﾄﾙｸで固定する事",
"裏から見た写真",
"PIN の取付に注意する事",
"1完成品のﾋﾟﾝを挿入",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ﾋﾟﾝ取付)",
"WorkItems": [
"2. 1完成品を㉙治具にセットしピンの位置決めを行い固定する",
"▲1. ①へPIN をNUT で取付(20ｶ所)"
],
"WorkPoints": [
"全てﾋﾟﾝの溝が治具に入った事を確認し､全てのﾋﾟﾝを規定ﾄﾙｸで固定する事",
"裏から見た写真",
"1完成品のﾋﾟﾝを挿入",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ位置合わせ治具",
"Size": "",
"ToolOther": "FM-6555",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ﾋﾟﾝ取付)",
"WorkItems": [
"2. 1完成品を㉙治具にセットしピンの位置決めを行い固定する",
"▲1. ①へPIN をNUT で取付(20ｶ所)"
],
"WorkPoints": [
"全てﾋﾟﾝの溝が治具に入った事を確認し､全てのﾋﾟﾝを規定ﾄﾙｸで固定する事",
"裏から見た写真",
"1完成品のﾋﾟﾝを挿入",
"横から... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6555",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｽﾍﾟｰｻｰ取付)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｽﾍﾟｰｻｰ取付)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(基板取付)",
"WorkItems": [
"■1. 20-ROW FEEDER CART BOARD の型式を検査表で確認し､ｼﾘｱ№を検査表に記載する事",
"★2. ①に20-ROW FEEDER CART BOARD をSCREW で取付(6ｶ所)"
],
"WorkPoints": [
"図の右手前に大きいｺﾈｸﾀがくる事",
"20-ROW FEEDER CART BOARD 取付方向に... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEWD-F013-051",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(基板取付)",
"WorkItems": [
"■1. 20-ROW FEEDER CART BOARD の型式を検査表で確認し､ｼﾘｱ№を検査表に記載する事",
"★2. ①に20-ROW FEEDER CART BOARD をSCREW で取付(6ｶ所)"
],
"WorkPoints": [
"図の右手前に大きいｺﾈｸﾀがくる事",
"20-ROW FEED... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(配線接続)",
"WorkItems": [
"1. CABLE にLABEL を取付",
"★2. ①に1完成品を接続する(20ｶ所)"
],
"WorkPoints": [
"黒いｺﾈｸﾀ側にﾗﾍﾞﾙﾀｲ側を接続する",
"LABEL は20種類あり(負荷ﾗﾍﾞﾙ:CN41/SLOT1~CN60/SLOT20)",
"CN60/SLOT20のｺﾈｸﾀ接続する事(接続番号に注意する事)",... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEWD-F013-051",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｶﾊﾞｰ取付)",
"WorkItems": [
"2. 1完成品を①にBOLT WASHER で取付",
"1. BUSH を各指示寸法にｶｯﾄし､COVER に取付"
],
"WorkPoints": [
"1完成品取付時配線が噛み込み､ｴｯﾁﾞ干渉無き事",
"L=210±1㎜×1､L=395±1㎜×1"
],
"Tolks": [],
"InspectionNo... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｶﾊﾞｰ取付)",
"WorkItems": [],
"WorkPoints": [
"ﾄﾘﾑを奥まで押し込んで貼付ける",
"210㎜を貼付ける",
"395㎜を貼付ける",
"配線をｴｯﾁﾞ部に干渉させ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(配線処理)",
"WorkItems": [
"1. ①の配線を㉖で固定する"
],
"WorkPoints": [
"4ｶ所固定(5本/SET)",
"配線の干渉無き事",
"配線をｴｯﾁﾞ部に干渉させ無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ﾋﾟﾝ圧入)",
"WorkItems": [
"2. 1完成品にPIN を(2個)圧入する",
"3. 2完成品にPIN を(6個)圧入する",
"1. PLATE にPIN を(3個)圧入する",
"2. 1完成品にPIN を(2個)圧入する",
"3. 2完成品にPIN を(6個)圧入する",
"1. PLATE にPIN を(3個)圧入する",
"2. 1完成... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌｨｰﾀﾞ偏芯ﾋﾟﾝ位置決めﾌﾟﾚｰﾄ組立(ﾋﾟﾝ圧入)",
"WorkItems": [
"2. 1完成品にPLATE をBOLT で取付ける",
"1. PLATE にSPRING-PLATE を(20個)挿入する"
],
"WorkPoints": [
"・PLATE の取付位置に注意する事・㉘ピンゲージがPLATE PLATE 通して固定する事",
"SPRING-PLATE の向きに注意する事",... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝｹﾞｰｼﾞ",
"Size": "φ5",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ偏芯ﾋﾟﾝ位置決めﾌﾟﾚｰﾄ組立(ﾋﾟﾝ圧入)",
"WorkItems": [
"2. 1完成品にPLATE をBOLT で取付ける",
"1. PLATE にSPRING-PLATE を(20個)挿入する"
],
"WorkPoints": [
"・PLATE の取付位置に注意する事・㉘ピンゲージがPLATE PLATE 通して固定する事",
"SPRING-PLATE の向きに注意する事",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝｹﾞｰｼﾞが通る事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ偏芯ﾋﾟﾝ位置決めﾌﾟﾚｰﾄ組立(ｶﾊﾞｰ取付)",
"WorkItems": [
"1. ①にCOVER をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"COVER の向きと位置に注意する事",
"面一に固定する"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾌｨｰﾀﾞ偏芯ﾋﾟﾝ位置決めﾌﾟﾚｰﾄ組立(ｶﾊﾞｰ取付)",
"WorkItems": [
"1. ①にCOVER をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"COVER の向きと位置に注意する事",
"面一に固定する"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ﾌﾞﾗｹｯﾄ取付)",
"WorkItems": [
"1. ①にGUIDE (3個)をBOLT WASHER で仮取付"
],
"WorkPoints": [
"GUIDE をﾋﾟﾝに挿入しと取付向きに注意する",
"ﾋﾟﾝに挿入",
"R側を外向きにする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ｸﾗﾝﾌﾟ取付)",
"WorkItems": [
"2. ①作業が完了次第､右記図のﾎﾞﾀﾝﾎﾞﾙﾄを増し締めする",
"◆1. ①にBRACKET (UNIT) SHAFT WASHER を通して､BOLT WASHER で取付"
],
"WorkPoints": [
"①のﾌﾞﾗｹｯﾄの間にもWASHER を取付",
"BRACKET (UNIT) の向きに注意する",
"1の作業完... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1個",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ｸﾗﾝﾌﾟ取付)",
"WorkItems": [
"◆1. ①にBRACKET (UNIT) SHAFT WASHER を通して､BOLT WASHER で取付"
],
"WorkPoints": [
"①のﾌﾞﾗｹｯﾄの間にもWASHER を取付",
"BRACKET (UNIT) の向きに注意する",
"･BRACKET (UNIT) の向きとWASHER を忘れずに... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ｸﾗﾝﾌﾟ取付)",
"WorkItems": [
"2. ①作業が完了次第､右記図のﾎﾞﾀﾝﾎﾞﾙﾄを増し締めする",
"◆1. ①にBRACKET (UNIT) SHAFT WASHER を通して､BOLT WASHER で取付"
],
"WorkPoints": [
"①のﾌﾞﾗｹｯﾄの間にもWASHER を取付",
"BRACKET (UNIT) の向きに注意する",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "190cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ｽﾌﾟﾘﾝｸﾞ取付)",
"WorkItems": [
"◆1. ①のｸﾗﾝﾌﾟ部にSPRING BOLT を取付"
],
"WorkPoints": [
"ｸﾞﾘｰｽを塗布し取付",
"･SPRING BOLT の取付位置に注意する事･SPRING にｸﾞﾘｰｽを塗布する",
"ｸﾗﾝﾌﾟの真ん中の穴で固定する"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:各1個",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ｽﾌﾟﾘﾝｸﾞ取付)",
"WorkItems": [
"◆1. ①のｸﾗﾝﾌﾟ部にSPRING BOLT を取付"
],
"WorkPoints": [
"ｸﾞﾘｰｽを塗布し取付",
"･SPRING BOLT の取付位置に注意する事･SPRING にｸﾞﾘｰｽを塗布する",
"ｸﾗﾝﾌﾟの真ん中の穴で固定する"
],
"Tolks": [
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "120cN･m",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ｶﾞｲﾄﾞ取付)",
"WorkItems": [
"1. ①にGUIDE (21個)をBOLT (42個)で取付",
"2. 1完成品にGUIDE をBOLT (4個)で取付",
"1. ①にGUIDE (21個)をBOLT (42個)で取付",
"2. 1完成品にGUIDE をBOLT (4個)で取付"
],
"WorkPoints": [
"G... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から15±1㎜",
"ｶﾞｲﾄﾞから2±1㎜",
"ﾌﾟﾚｰﾄ端面から15±1㎜",
"ﾌﾟﾚｰﾄ端面から2±1㎜",
"下記指示寸法位置に㉖㉗で脱脂後貼付ける"
],
"Tolks": [],
"Inspec... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ端面から15±1㎜",
"ｶﾞｲﾄﾞから2±1㎜",
"ﾌﾟﾚｰﾄ端面から15±1㎜",
"ﾌﾟﾚｰﾄ端面から2±1㎜",
"下記指示寸法位置に㉖㉗で脱脂後貼付ける"
],
"Tolks": [],
"Inspec... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "偏芯ﾋﾟﾝﾌﾟﾚｰﾄ組立(側面ﾌﾟﾚｰﾄﾋﾟﾝ圧入)",
"WorkItems": [
"1. PLATE にPIN を圧入する事(2ｹ製作)"
],
"WorkPoints": [
"ﾋﾟﾝ出代 : 5mm",
"PIN の出代に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "偏芯ﾋﾟﾝﾌﾟﾚｰﾄ組立(側面、下面ﾌﾟﾚｰﾄ取付)",
"WorkItems": [],
"WorkPoints": [
"①のﾋﾟﾝにPLATE を入れる",
"PLATE の座繰り面に注意する",
"①のﾋﾟﾝに②を入れる",
"①のﾋﾟﾝにPLATE を入れる",
"PLATE の座繰り面に注意する",
"①のﾋﾟﾝに②を入れる"
],
"Tolks": [
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "偏芯ﾋﾟﾝﾌﾟﾚｰﾄ組立(側面、下面ﾌﾟﾚｰﾄ取付)",
"WorkItems": [],
"WorkPoints": [
"①のﾋﾟﾝにPLATE を入れる",
"PLATE の座繰り面に注意する",
"①のﾋﾟﾝに②を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"Inspe... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "偏芯ﾋﾟﾝﾌﾟﾚｰﾄ組立(上部ﾌﾟﾚｰﾄ取付)",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"2. 1完成品にCOVER をWASHER BOLT で取付",
"1. ①に②をBOLT WASHER で取付",
"2. 1完成品にCOVER をWASHER BOLT で取付"
],
"WorkPoints": [
"COVER の形状を確認し右図の向きで取... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｰｹﾞｯﾄﾎﾟｰﾙ部組立",
"WorkItems": [
"▲1. SHAFT を㉖で脱脂後にTARGET を㉗㉘で接着する",
"2. 1.完成品にSCREW を取付ける"
],
"WorkPoints": [
"出代 :8±1mm※手で奥まで入れる事",
"TARGET が傷つける事がないよう保護する事",
"･割れやすいので注意･作業終了後､ｴｱﾊﾟｯｷﾝ､ 保護ﾃｰﾌﾟ等で包んでおく･ ｱﾙｺｰﾙで汚れを拭く"... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｽｰﾊﾟｰX№8008",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾀｰｹﾞｯﾄﾎﾟｰﾙ部組立",
"WorkItems": [
"▲1. SHAFT を㉖で脱脂後にTARGET を㉗㉘で接着する",
"2. 1.完成品にSCREW を取付ける"
],
"WorkPoints": [
"出代 :8±1mm※手で奥まで入れる事",
"TARGET が傷つける事がないよう保護する事",
"･割れやすいので注意･作業終了後､ｴｱﾊﾟｯｷﾝ､ 保護ﾃｰﾌﾟ等で包んでおく･ ｱﾙｺｰﾙ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ﾀｰｹﾞｯﾄﾎﾟｰﾙ取付)",
"WorkItems": [
"1. ①に②を㉖㉗で取付"
],
"WorkPoints": [
"ベース上面よりボルト出代に注意し、㉖でセットビスを固定して②を締結する",
"㉗スパナで締付"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ﾀｰｹﾞｯﾄﾎﾟｰﾙ取付)",
"WorkItems": [
"1. ①に②を㉖㉗で取付"
],
"WorkPoints": [
"ベース上面よりボルト出代に注意し、㉖でセットビスを固定して②を締結する",
"㉗スパナで締付"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ｴｱｰﾌﾞﾛｯｸ部取付)",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"②の取付方法に注意する事",
"②を①のﾋﾟﾝに挿入し取付ける",
"ｸﾗﾝﾌﾟの下に入るように取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(連結ﾌﾟﾚｰﾄ取付)",
"WorkItems": [
"1. ①にPLATE をBOLT WASHER で仮止め"
],
"WorkPoints": [
"PLATE の取付方向と位置に注意する事",
"PLATE のﾀｯﾌﾟが内側に向く事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "3.0N･m",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ部払出し",
"WorkItems": [
"1. ①に㉘を使用し②をBOLT WASHER で取付"
],
"WorkPoints": [
"㉘を下記の方法で使用しBOLT ボルトを締付",
"㉘をスロット１、スロット20へセットする"
],
"Tolks": [
"治具",
"治具",
"治具",
"治具",
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞﾋﾟﾝ位置決め治具",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ部払出し",
"WorkItems": [
"1. ①に㉘を使用し②をBOLT WASHER で取付"
],
"WorkPoints": [
"㉘を下記の方法で使用しBOLT ボルトを締付",
"㉘をスロット１、スロット20へセットする"
],
"Tolks": [
"治具",
"治具",
"治具",
"治具",
"締付ﾄﾙｸ ... | {
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り部材確認出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Ⅹ軸ｹｰﾌﾞﾙﾍﾞｱ取付ﾌﾟﾚｰﾄ部組立",
"WorkItems": [
"1. PLATE 脱脂後にBUSH を貼付",
"2. 1完成品にCABLE-SUPPORT を取付(6ｶ所)"
],
"WorkPoints": [
"BUSH を150㎜にｶｯﾄしPLATE へ貼付",
"ﾄﾘﾑが全てｶﾊﾞｰに引っ掛かり貼付いている事"
],
"Tolks": [],
"InspectionNo": "... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Ⅹ軸ﾛﾎﾞｼﾘﾝﾀﾞｰ部組立(ﾋﾟﾝ圧入)",
"WorkItems": [
"1. PLATE にPIN を圧入する(4ｶ所)"
],
"WorkPoints": [
"PIN の圧入場所､裏表､出代に注意する事",
"出代4±0.5㎜",
"出代4±0.5㎜",
"出代4±0.5㎜",
"出代4±0.5㎜",
"凹面に圧入する事"
],
"Tolks": [],
"I... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Ⅹ軸ﾛﾎﾞｼﾘﾝﾀﾞｰ部組立(ｸﾞﾘｰｽ用継手取付)",
"WorkItems": [
"2. 1完成品のｾｯﾄﾋﾞｽを取り除く事(廃棄する事)",
"3. 2完成品にJOINT を(2個)取付",
"■1. CYLINDER X軸ﾛﾎﾞｼﾘﾝﾀﾞｼﾘｱﾙNo記入および型式の確認を行う"
],
"WorkPoints": [
"･JOINT の締め過ぎに注意する事･ﾛﾎﾞｼﾘﾝﾀﾞｰのｽﾃﾝﾚｽｼｰﾄの取り扱いに注意する事",
... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEWD-F013-001",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.5N･m",
"WorkName": "Ⅹ軸ﾛﾎﾞｼﾘﾝﾀﾞｰ部組立(ｸﾞﾘｰｽ用継手取付)",
"WorkItems": [
"2. 1完成品のｾｯﾄﾋﾞｽを取り除く事(廃棄する事)",
"3. 2完成品にJOINT を(2個)取付",
"■1. CYLINDER X軸ﾛﾎﾞｼﾘﾝﾀﾞｼﾘｱﾙNo記入および型式の確認を行う"
],
"WorkPoints": [
"･JOINT の締め過ぎに注意する事･ﾛﾎﾞｼﾘﾝﾀﾞｰのｽﾃﾝﾚｽｼｰﾄの取... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "Ⅹ軸ﾛﾎﾞｼﾘﾝﾀﾞｰ部組立(銘板貼付)",
"WorkItems": [
"1. ①にLABEL を貼付"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後貼付",
"端面から50±1㎜",
"端面から164±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "Ⅹ軸ﾛﾎﾞｼﾘﾝﾀﾞｰ部組立(ﾛﾎﾞｼﾘﾝﾀﾞｰ取付)",
"WorkItems": [
"1. ①に砥石をかけ､ﾊﾞﾘなどの除去､確認",
"2. 1完成品に②をBOLT WASHER で取付"
],
"WorkPoints": [
"②を①のﾋﾟﾝ(2本)に挿入し､取付",
"ﾋﾟﾝに挿入し取付",
"ﾋﾟﾝに挿入し取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.4N･m"
],
... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.4N･m",
"WorkName": "Ⅹ軸ﾛﾎﾞｼﾘﾝﾀﾞｰ部組立(ﾛﾎﾞｼﾘﾝﾀﾞｰ取付)",
"WorkItems": [
"1. ①に砥石をかけ､ﾊﾞﾘなどの除去､確認",
"2. 1完成品に②をBOLT WASHER で取付"
],
"WorkPoints": [
"②を①のﾋﾟﾝ(2本)に挿入し､取付",
"ﾋﾟﾝに挿入し取付",
"ﾋﾟﾝに挿入し取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.4... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.4N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "制御BOX下ｶﾊﾞｰ組立(FT4取付)",
"WorkItems": [
"1. PLATE にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"PLATE の表裏､向き､位置に注意しCABLE-SUPPORT を取付",
"PLATE の切り欠きで向きを確認する事",
"PLATE の切り欠きで向きを確認する事",
"CABLE-SUPPORT の穴の向き(3つ同じ方向)"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ側板金組立(銘板貼付け)",
"WorkItems": [
"1. COVER にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖で脱脂後貼付ける",
"端面から5±1㎜",
"端面から315±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "正面ｶﾊﾞｰ組立(ﾗﾍﾞﾙ貼付)",
"WorkItems": [
"1. COVER にLABEL を貼付"
],
"WorkPoints": [
"端面から44±1㎜",
"端面から5±1㎜",
"下記指示寸法位置に㉖で脱脂後貼付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "右側面ｶﾊﾞｰ下部組立(ﾗﾍﾞﾙ貼付)",
"WorkItems": [
"1. COVER にLABEL を貼付"
],
"WorkPoints": [
"端面から20±1㎜",
"端面から50±1㎜",
"365㎜ﾋﾟｯﾁ面を下にして貼付",
"・下記指示寸法位置に㉖で脱脂後貼付・LABEL を貼る面に注意する事"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側面ｶﾊﾞｰ下部組立(ｹｰﾌﾞﾙｸﾗﾝﾌﾟ取付)",
"WorkItems": [
"1. COVER にCLAMP を取付"
],
"WorkPoints": [
"CLAMP のｸﾗﾝﾌﾟﾛｯｸと挿入位置に注意する事",
"ｶﾊﾞｰの裏面に出ている事",
"ｸﾗﾝﾌﾟﾛｯｸ部がｶﾊﾞｰの外側へ向く事",
"青枠は本体取付用ﾎﾞﾙﾄ穴"
],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"1. BRACKET にRUBBER-CUSHION をBOLT で取付ける",
"2. BRACKET にRUBBER-CUSHION をBOLT で取付ける"
],
"WorkPoints": [
"RUBBER-CUSHION のｸｯｼｮﾝの取付方向に注意",
"BRACKET の折曲げ方向に注意して取付け",
"BRACKET の折曲げ方向に注意して... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "開閉ｶﾊﾞｰｽﾄｯﾊﾟｰ組立",
"WorkItems": [],
"WorkPoints": [
"BRACKET の折曲げ方向に注意して取付け",
"BRACKET の折曲げ方向に注意して取付け",
"BRACKET の折曲げ方向に注意して取付け",
"BRACKET の折曲げ方向に注意して取付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "X軸ﾛﾎﾞｼﾘﾝﾀﾞｰ前ｶﾊﾞｰ取付け",
"WorkItems": [
"1. ①に⑥をSCREW で取付ける",
"3. 2完成品にCOVER をBOLT WASHER にて取付",
"2. 1完成品にCOVER をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "X軸ﾛﾎﾞｼﾘﾝﾀﾞｰ前ｶﾊﾞｰ取付け",
"WorkItems": [
"1. ①に⑥をSCREW で取付ける",
"3. 2完成品にCOVER をBOLT WASHER にて取付",
"2. 1完成品にCOVER をSCREW で取付ける",
"1. ①に⑥をSCREW で取付ける",
"3. 2完成品にCOVER をBOLT WASHER にて取付",
"2. 1完成品にCOVER... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "内側板金取付",
"WorkItems": [
"1. ①にCOVER COVER COVER をBOLT WASHER にて取付"
],
"WorkPoints": [
"COVER は左右設備外側へ当付けで取付",
"【取付目安】 前面ﾌﾚｰﾑより3±0.5㎜の位置にて取付",
"エアチューブの嚙み込みに注意",
"配線の嚙み込みに注意"
],
"Tolks": [
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "内側板金取付",
"WorkItems": [
"1. ①にCOVER COVER COVER をBOLT WASHER にて取付"
],
"WorkPoints": [
"COVER は左右設備外側へ当付けで取付",
"【取付目安】 前面ﾌﾚｰﾑより3±0.5㎜の位置にて取付",
"エアチューブの嚙み込みに注意",
"配線の嚙み込みに注意"
],
"Tolks": [
"締付ﾄﾙｸ 9... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "内側板金取付",
"WorkItems": [
"1. ①にCOVER COVER COVER をBOLT WASHER にて取付"
],
"WorkPoints": [
"COVER は左右設備外側へ当付けで取付",
"【取付目安】 前面ﾌﾚｰﾑより3±0.5㎜の位置にて取付",
"エアチューブの嚙み込みに注意",
"配線の嚙み込みに注意"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "内側板金取付",
"WorkItems": [
"1. ①にCOVER COVER COVER をBOLT WASHER にて取付"
],
"WorkPoints": [
"COVER は左右設備外側へ当付けで取付",
"【取付目安】 前面ﾌﾚｰﾑより3±0.5㎜の位置にて取付",
"エアチューブの嚙み込みに注意",
"配線の嚙み込みに注意"
],
"Tolks": [
"締付ﾄﾙｸ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ｶﾊﾞｰﾌﾚｰﾑ取付",
"WorkItems": [
"1. ①に②をBOLT BOLT にて取付"
],
"WorkPoints": [
"架台ﾌﾚｰﾑ端面とｶﾊﾞｰﾌﾚｰﾑ端面を揃える ※ｶﾊﾞｰ取付後の出来栄えに影響"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｶﾊﾞｰﾌﾚｰﾑ取付",
"WorkItems": [
"1. ①に②をBOLT BOLT にて取付",
"2. ｶﾊﾞｰﾌﾚｰﾑの修正･増し締め"
],
"WorkPoints": [
"架台ﾌﾚｰﾑ端面とｶﾊﾞｰﾌﾚｰﾑ端面を揃える ※ｶﾊﾞｰ取付後の出来栄えに影響",
"ｶﾊﾞｰﾌﾚｰﾑ各接合部のｽﾞﾚを確認し､必要なら修正･増締め実施"
],
"Tolks": [
"締付ﾄﾙｸ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰﾌﾚｰﾑ取付",
"WorkItems": [
"1. ①に②をBOLT BOLT にて取付",
"2. ｶﾊﾞｰﾌﾚｰﾑの修正･増し締め"
],
"WorkPoints": [
"架台ﾌﾚｰﾑ端面とｶﾊﾞｰﾌﾚｰﾑ端面を揃える ※ｶﾊﾞｰ取付後の出来栄えに影響",
"ｶﾊﾞｰﾌﾚｰﾑ各接合部のｽﾞﾚを確認し､必要なら修正･増締め実施"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.