input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "右側面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をSCREW BOLT WASHER にて取付",
"2. 機内配線を接続･結束する"
],
"WorkPoints": [
"架台ﾌﾚｰﾑとｶﾊﾞｰﾌﾚｰﾑ端面の平行を揃える",
"端面の平行を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "右側面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をSCREW BOLT WASHER にて取付",
"2. 機内配線を接続･結束する"
],
"WorkPoints": [
"架台ﾌﾚｰﾑとｶﾊﾞｰﾌﾚｰﾑ端面の平行を揃える",
"端面の平行を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": ""... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をSCREW BOLT WASHER にて取付",
"2. 機内配線を接続･結束する"
],
"WorkPoints": [
"架台ﾌﾚｰﾑとｶﾊﾞｰﾌﾚｰﾑ端面の平行を揃える",
"端面の平行を揃える",
"上下方向はSUSと合わせる"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 300cN･... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "右側面ｶﾊﾞｰ取付(後側)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"下記指示通り取付",
"端面の平行を揃える",
"前ｶﾊﾞｰ側に当付けて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側面ｶﾊﾞｰ取付(後側)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"下記指示通り取付",
"端面の平行を揃える",
"前ｶﾊﾞｰ側に当付けて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "左側面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW BOLT WASHER にて取付"
],
"WorkPoints": [
"架台ﾌﾚｰﾑとｶﾊﾞｰﾌﾚｰﾑ端面の平行を揃える",
"端面の平行を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 300cN･m"
],
"Inspecti... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "左側面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW BOLT WASHER にて取付"
],
"WorkPoints": [
"架台ﾌﾚｰﾑとｶﾊﾞｰﾌﾚｰﾑ端面の平行を揃える",
"端面の平行を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW BOLT WASHER にて取付"
],
"WorkPoints": [
"架台ﾌﾚｰﾑとｶﾊﾞｰﾌﾚｰﾑ端面の平行を揃える",
"端面の平行を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "左側面ｶﾊﾞｰ取付(後側)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"下記指示通り取付",
"端面の平行を揃える",
"前ｶﾊﾞｰ側に当付けて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側面ｶﾊﾞｰ取付(後側)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"下記指示通り取付",
"端面の平行を揃える",
"前ｶﾊﾞｰ側に当付けて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "天井ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"･COVER ｶﾊﾞｰの前後左右の位置に注意して取付ること･側面ｶﾊﾞｰ(前側)との位置に注意する事",
"SUSとCOVER の面を揃える",
"SUSとCOVER の面を揃える",
"SCREW 7ｶ所固定"
],
"Tolks... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "天井ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"･COVER ｶﾊﾞｰの前後左右の位置に注意して取付ること･側面ｶﾊﾞｰ(前側)との位置に注意する事",
"SUSとCOVER の面を揃える",
"SUSとCOVER の面を揃える",
"SCREW 7ｶ所固定"
],
"Tolks": [
"締付... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "中央ｶﾊﾞｰとの隙間:2±0.5㎜左右均等の事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "天井ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"･COVER ｶﾊﾞｰの前後左右の位置に注意して取付ること･側面ｶﾊﾞｰ(前側)との位置に注意する事",
"SUSとCOVER の面を揃える",
"SUSとCOVER の面を揃える",
"SCREW 7ｶ所固定"
],
"Tolks": [
"締付ﾄﾙｸ 300... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "開閉ｶﾊﾞｰ取付(取付隙間調整)",
"WorkItems": [
"◆1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"･開閉ｶﾊﾞｰの左右隙間を均等に取付後､目安となる数値が下略図です･二人作業で取付を行う事(一人が②を保持作業､一人がﾋﾝｼﾞへの取付作業)",
"･開閉ｶﾊﾞｰの左右隙間は SUSの隙間で測定する(ｷｬｯﾌﾟ含まず)"
],
"Tolks":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ取付(取付隙間調整)",
"WorkItems": [
"◆1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"･開閉ｶﾊﾞｰの左右隙間を均等に取付後､目安となる数値が下略図です･二人作業で取付を行う事(一人が②を保持作業､一人がﾋﾝｼﾞへの取付作業)",
"･開閉ｶﾊﾞｰの左右隙間は SUSの隙間で測定する(ｷｬｯﾌﾟ含まず)"
],
"Tolks": [
"締付ﾄﾙ... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各ｶﾊﾞｰとの隙間7.5㎜以下2.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "開閉ｶﾊﾞｰ取付(ｶﾞｽｽﾌﾟﾘﾝｸﾞ部)",
"WorkItems": [
"◆1. ｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄをBOLT WASHER にてやぐらﾌﾚｰﾑへ取付"
],
"WorkPoints": [
"左右のｶﾊﾞｰ面~ﾌﾞﾗｹｯﾄ面の寸法に調整する ※略図茶線部分",
"15.5±0.5㎜",
"56±0.5㎜",
"二人作業で取付を行う事(一人が開閉ｶﾊﾞｰを保持､一人がﾌﾞﾗｹｯ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ取付(ｶﾞｽｽﾌﾟﾘﾝｸﾞ部)",
"WorkItems": [
"◆1. ｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄをBOLT WASHER にてやぐらﾌﾚｰﾑへ取付"
],
"WorkPoints": [
"左右のｶﾊﾞｰ面~ﾌﾞﾗｹｯﾄ面の寸法に調整する ※略図茶線部分",
"15.5±0.5㎜",
"56±0.5㎜",
"二人作業で取付を行う事(一人が開閉ｶﾊﾞｰを保持､一人がﾌﾞﾗｹｯﾄ取付作業)... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各ｶﾊﾞｰとの隙間15.5±0.5㎜56±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ取付(ｶﾞｽｽﾌﾟﾘﾝｸﾞ部)",
"WorkItems": [
"◆1. ｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄをBOLT WASHER にてやぐらﾌﾚｰﾑへ取付"
],
"WorkPoints": [
"左右のｶﾊﾞｰ面~ﾌﾞﾗｹｯﾄ面の寸法に調整する ※略図茶線部分",
"15.5±0.5㎜",
"56±0.5㎜",
"二人作業で取付を行う事(一人が開閉ｶﾊﾞｰを保持､一人がﾌﾞﾗｹｯﾄ取付作業)"
],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ取付(高さ確認)",
"WorkItems": [
"1. 開閉ｶﾊﾞｰの開閉動作確認",
"3. 開閉ｶﾊﾞｰの高さ確認",
"2. ｶﾊﾞｰ段差を調整する",
"1. 開閉ｶﾊﾞｰの開閉動作確認",
"3. 開閉ｶﾊﾞｰの高さ確認",
"2. ｶﾊﾞｰ段差を調整する"
],
"WorkPoints": [
"ｽﾑｰｽﾞに実施出来る事",
"【異音】 開閉ｽﾋﾟｰﾄ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "6㎜~12㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "開閉ｶﾊﾞｰ取付(高さ確認)",
"WorkItems": [
"1. 開閉ｶﾊﾞｰの開閉動作確認",
"3. 開閉ｶﾊﾞｰの高さ確認",
"2. ｶﾊﾞｰ段差を調整する"
],
"WorkPoints": [
"ｽﾑｰｽﾞに実施出来る事",
"【異音】 開閉ｽﾋﾟｰﾄﾞを変化させて発生確認",
"開閉ｶﾊﾞｰ閉じた時A=6㎜~12㎜",
"開閉ｶﾊﾞｰ全閉でのｶﾞｽｽﾌﾟﾘﾝ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "開閉ｶﾊﾞｰ取付(高さ確認)",
"WorkItems": [
"1. 開閉ｶﾊﾞｰの開閉動作確認",
"3. 開閉ｶﾊﾞｰの高さ確認",
"2. ｶﾊﾞｰ段差を調整する"
],
"WorkPoints": [
"ｽﾑｰｽﾞに実施出来る事",
"【異音】 開閉ｽﾋﾟｰﾄﾞを変化させて発生確認",
"開閉ｶﾊﾞｰ閉じた時A=6㎜~12㎜",
"開閉ｶﾊﾞｰ全閉でのｶ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ取付(高さ確認)",
"WorkItems": [
"1. 開閉ｶﾊﾞｰの開閉動作確認",
"3. 開閉ｶﾊﾞｰの高さ確認",
"2. ｶﾊﾞｰ段差を調整する"
],
"WorkPoints": [
"15.5±0.5㎜",
"ｽﾑｰｽﾞに実施出来る事",
"【異音】 開閉ｽﾋﾟｰﾄﾞを変化させて発生確認",
"開閉ｶﾊﾞｰ閉じた時A=6㎜~12㎜",
"ｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ取付(高さ確認)",
"WorkItems": [
"1. 開閉ｶﾊﾞｰの開閉動作確認",
"3. 開閉ｶﾊﾞｰの高さ確認",
"2. ｶﾊﾞｰ段差を調整する",
"1. 開閉ｶﾊﾞｰの開閉動作確認",
"3. 開閉ｶﾊﾞｰの高さ確認",
"2. ｶﾊﾞｰ段差を調整する"
],
"WorkPoints": [
"ｽﾑｰｽﾞに実施出来る事",
"【異音】 開閉ｽﾋﾟｰﾄ... | {
"QualityItem": "段差確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｶﾊﾞｰとの段差:2±1㎜の事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "開閉ｶﾊﾞｰ取付(高さ確認)",
"WorkItems": [
"1. 開閉ｶﾊﾞｰの開閉動作確認",
"3. 開閉ｶﾊﾞｰの高さ確認",
"2. ｶﾊﾞｰ段差を調整する"
],
"WorkPoints": [
"ｽﾑｰｽﾞに実施出来る事",
"【異音】 開閉ｽﾋﾟｰﾄﾞを変化させて発生確認",
"開閉ｶﾊﾞｰ閉じた時A=6㎜~12㎜",
"開閉ｶﾊﾞｰ全閉でのｶﾞｽｽﾌﾟﾘﾝ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "異物落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①へCOVER COVER SPACER をBOLT BOLT WASHER にて取付"
],
"WorkPoints": [
"51.5±0.5mm",
"･開閉ｶﾊﾞｰの高さ､隙間調整完了後､作業する事･COVER とｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄの間にCOVER を入れる事",
"COVER の向きはﾎﾞﾙﾄ穴で判断する事... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "異物落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①へCOVER COVER SPACER をBOLT BOLT WASHER にて取付"
],
"WorkPoints": [
"51.5±0.5mm",
"･開閉ｶﾊﾞｰの高さ､隙間調整完了後､作業する事･COVER とｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄの間にCOVER を入れる事",
"COVER の向きはﾎﾞﾙﾄ穴で判断する事",
"2±0.5mm"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "異物落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①へCOVER COVER SPACER をBOLT BOLT WASHER にて取付"
],
"WorkPoints": [
"51.5±0.5mm",
"･開閉ｶﾊﾞｰの高さ､隙間調整完了後､作業する事･COVER とｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄの間にCOVER を入れる事",
"COVER の向きはﾎﾞﾙﾄ穴で判断する事",
"2±... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各ｶﾊﾞｰとの隙間51.5±0.5㎜2.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "異物落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①へCOVER COVER SPACER をBOLT BOLT WASHER にて取付"
],
"WorkPoints": [
"51.5±0.5mm",
"･開閉ｶﾊﾞｰの高さ､隙間調整完了後､作業する事･COVER とｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄの間にCOVER を入れる事",
"COVER の向きはﾎﾞﾙﾄ穴で判断する事... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "異物落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①へCOVER COVER SPACER をBOLT BOLT WASHER にて取付"
],
"WorkPoints": [
"51.5±0.5mm",
"･開閉ｶﾊﾞｰの高さ､隙間調整完了後､作業する事･COVER とｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄの間にCOVER を入れる事",
"COVER の向きはﾎﾞﾙﾄ穴で判断する事",
"2±0.5mm"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "異物落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①へCOVER COVER SPACER をBOLT BOLT WASHER にて取付"
],
"WorkPoints": [
"51.5±0.5mm",
"･開閉ｶﾊﾞｰの高さ､隙間調整完了後､作業する事･COVER とｶﾞｽｽﾌﾟﾘﾝｸﾞﾌﾞﾗｹｯﾄの間にCOVER を入れる事",
"COVER の向きはﾎﾞﾙﾄ穴で判断する事",
"2±... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各ｶﾊﾞｰとの隙間51.5±0.5㎜2.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T10",
"ToolOther": "150cN･m",
"WorkName": "開閉ｶﾊﾞｰ取付(安全SWﾚﾊﾞｰ)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "3.2N･m",
"WorkName": "開閉ｶﾊﾞｰ取付(安全SWﾚﾊﾞｰ)",
"WorkItems": [
"◆1. 安全SWのﾚﾊﾞｰをBOLT SPACER WASHER で取付",
"2. 安全SWのﾚﾊﾞｰが開閉ｶﾊﾞｰと平行になっているか目視確認"
],
"WorkPoints": [
"SPACER 外周にｸﾞﾘｰｽ塗布",
"微調整が必要な場合は緑丸部分で実施して下さい",
"ﾚﾊﾞｰとｶﾊﾞｰが平行で干渉... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ取付(安全SWﾚﾊﾞｰ)",
"WorkItems": [
"◆1. 安全SWのﾚﾊﾞｰをBOLT SPACER WASHER で取付",
"2. 安全SWのﾚﾊﾞｰが開閉ｶﾊﾞｰと平行になっているか目視確認"
],
"WorkPoints": [
"SPACER 外周にｸﾞﾘｰｽ塗布",
"微調整が必要な場合は緑丸部分で実施して下さい",
"ﾚﾊﾞｰとｶﾊﾞｰが平行で干渉無き事"
],
"Tolk... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ取付(安全SWﾚﾊﾞｰ)",
"WorkItems": [
"◆1. 安全SWのﾚﾊﾞｰをBOLT SPACER WASHER で取付",
"2. 安全SWのﾚﾊﾞｰが開閉ｶﾊﾞｰと平行になっているか目視確認"
],
"WorkPoints": [
"SPACER 外周にｸﾞﾘｰｽ塗布",
"微調整が必要な場合は緑丸部分で実施して下さい",
"ﾚﾊﾞｰとｶﾊﾞｰが平行で干渉無き事"
],
"Tolk... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "背面ｶﾊﾞｰ取付(上部)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"天井ｶﾊﾞｰと隙間なく平行に取付",
"左側面ｶﾊﾞｰと面一で取付"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面ｶﾊﾞｰ取付(上部)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"天井ｶﾊﾞｰと隙間なく平行に取付",
"左側面ｶﾊﾞｰと面一で取付"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "正面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"周辺ｶﾊﾞｰとの各隙間を下記指示通り取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "正面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"周辺ｶﾊﾞｰとの各隙間を下記指示通り取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各ｶﾊﾞｰとの隙間2±0.5㎜1±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"周辺ｶﾊﾞｰとの各隙間を下記指示通り取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTy... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "右側面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"周辺ｶﾊﾞｰとの各隙間を下記指示通り取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右側面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"周辺ｶﾊﾞｰとの各隙間を下記指示通り取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各ｶﾊﾞｰとの隙間2±0.5㎜1±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"周辺ｶﾊﾞｰとの各隙間を下記指示通り取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "左側面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"ｶﾊﾞｰ周辺の各隙間を均などに取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"ｶﾊﾞｰ周辺の各隙間を均などに取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各ｶﾊﾞｰとの隙間2±0.5㎜1±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①にCOVER をSCREW にて取付"
],
"WorkPoints": [
"ｶﾊﾞｰ周辺の各隙間を均などに取付",
"左右側面ｶﾊﾞｰの隙間を均などに取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "350cN･m",
"WorkName": "背面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"ｶﾊﾞｰ周辺の各隙間を均などに取付",
"左右側面ｶﾊﾞｰとの隙間を左右均等に取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 350cN･m"
],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "背面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"ｶﾊﾞｰ周辺の各隙間を均などに取付",
"左右側面ｶﾊﾞｰとの隙間を左右均等に取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 350cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各ｶﾊﾞｰとの隙間2±0.5㎜1±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面ｶﾊﾞｰ取付(下部)",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"ｶﾊﾞｰ周辺の各隙間を均などに取付",
"左右側面ｶﾊﾞｰとの隙間を左右均等に取付(目安:2㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 350cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送用ｷｬｽﾀｰの動作確認",
"WorkItems": [
"1. 搬送用ｷｬｽﾀｰの動作確認"
],
"WorkPoints": [
"搬送時を想定し､装置を直進･後退･旋回させ搬送用ｷｬｽﾀｰの動作が円滑か確認する"
],
"Tolks": [],
"InspectionNo": "WEWD-F013-001",
"InspectionItems": [
"検査表①:搬送ｷｬｽﾀｰの操作性確認"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "動作が円滑(引っ掛かりが有る)か確認する",
"Method": "目視",
"RecordMethod": "WEWD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "外装ｶﾊﾞｰ確認",
"WorkItems": [
"1. 外装ｶﾊﾞｰ確認"
],
"WorkPoints": [
"各外装ｶﾊﾞｰに､傷･打痕･ひび割れなどの異常がないか確認する"
],
"Tolks": [],
"InspectionNo": "WEWD-F013-001",
"InspectionItems": [
"検査表①:外装ｶﾊﾞｰ確認"
],
"WorkTypes": [],
"Wo... | {
"QualityItem": "美観ﾁｪｯｸ",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｷｽﾞ･打痕･塗装状態の確認",
"Method": "目視",
"RecordMethod": "WEWD-F013-001",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ準備",
"WorkItems": [
"1. 下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備しておく"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｹｰﾌﾞﾙ準備確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｰｷﾝｸﾞﾀｲ取付け・ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. CABLE にLABEL を取付ける"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞﾀｲの端をｺﾈｸﾀ端に合わせる",
"ｺﾈｸﾀの向きに注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "外側配線前準備",
"WorkItems": [
"1. CABLE-SUPPORT CABLE-SUPPORT に㉗を挿入し㉖に取付ける"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸをｹｰﾌﾞﾙｻﾎﾟｰﾄに通す方向は下図の通りとする",
"ｹｰﾌﾞﾙｻﾎﾟｰﾄの向き注意"
],
"Tolks": [],
"InspectionNo": "",
"Ins... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し1",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"YMM508",
"U/V/W(B)/E3K504"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し2",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"YMM504",
"U/V/W(A)/E2K504"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し3",
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に702Rを書く"
],
"WorkPoints": [
"Φ8白配管(下)",
"Φ8白配管(下)"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し4",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"XMM/EM503",
"U/V/W/E2K503"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し5",
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に701Rを書く"
],
"WorkPoints": [
"Φ8白配管(上)",
"Φ8白配管(上)"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し6",
"WorkItems": [
"1. ①を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CMRP",
"4K303",
"ｺﾈｸﾀの向きに注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "ﾊｰﾈｽ引き回確認1",
"WorkItems": [
"1. ﾊｰﾈｽの引き回しを確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"U/V/W(B)/K504",
"U/V/W(A)/K... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "内側配線前準備",
"WorkItems": [
"1. CABLE-SUPPORT CABLE-SUPPORT にインシュロックを挿入し㉖に取付ける"
],
"WorkPoints": [
"ｹｰﾌﾞﾙｻﾎﾟｰﾄの向き注意",
"ｲﾝｼｭﾛｯｸをｹｰﾌﾞﾙｻﾎﾟｰﾄに通す方向は下図の通りとする"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し7",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"YEM508",
"CN2BK504"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し8",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"YEM504",
"CN2AK504"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し9",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"1A22",
"CN6",
"HRPWA11"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し10",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CN1",
"HR_K313"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し11",
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に201Rを書く"
],
"WorkPoints": [
"Φ6黒配管",
"Φ6黒配管"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し12",
"WorkItems": [
"1. TUBE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する",
"2. 配管の先端に302を書く"
],
"WorkPoints": [
"Φ6黄配管",
"Φ6黄配管"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し13",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"XEM503",
"CN2K503"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "RXY配線引き回し14",
"WorkItems": [
"1. CABLE を引き回し､ｹｰﾌﾞﾙｻﾎﾟｰﾄに取付けたｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CN7",
"B113R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWXYﾕﾆｯﾄﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6370",
"WorkName": "ﾊｰﾈｽ引き回し確認2",
"WorkItems": [
"1. ﾊｰﾈｽの引き回しを確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"HRPWA11②",
"CN2K503",
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6370",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布1",
"WorkItems": [
"◆1. CABLE-BEAR CABLE-BEAR 付属のリングプレートの内側に㉖を塗布する"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布後紛失注意",
"ﾑﾗ･だまが無いように指で均等に塗り広げること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1枚当たり各1/2(0.05g)",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽKS-63W",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布2",
"WorkItems": [
"◆2. CABLE-BEAR CABLE-BEAR のベアのアーム内側３面に㉖を塗布する"
],
"WorkPoints": [
"あらかじめ塗る総量を出しておき､すべて使い切って塗布すること",
"ﾑﾗ･だまが無いように均等に塗り広げること",
"4.6g",
"5.8g"
],
"Tolks": [],
"InspectionNo": ""... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1ﾘﾝｸ当たり各1(0.1g)",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽKS-63W",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘｺﾝｸﾞﾘｰｽ塗布3",
"WorkItems": [
"◆2. ①②の下記指示部に㉗を塗布する",
"1. ①②のｹｰﾌﾞﾙｻﾎﾟｰﾄにｲﾝｼｭﾛｯｸを通す(1枚2箇所×8枚)"
],
"WorkPoints": [
"あらかじめ塗る総量を出しておき､すべて使い切って塗布すること",
"ﾑﾗ･だまが無いように均等に塗り広げること",
"2.4g",
"1.6g",
"3.2g",
"2.... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1ｹｰﾌﾞﾙ当たり各4(0.4g)",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽKS-63W",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾍﾞｱ取付け",
"WorkItems": [
"1. ①のX軸用ｹｰﾌﾞﾙﾍﾞｱをｾｯﾄする",
"3. ②の外側ｹｰﾌﾞﾙｻﾎﾟｰﾄの固定側を固定する",
"4. ②の外側ｹｰﾌﾞﾙｻﾎﾟｰﾄの可動側を固定する",
"5. 付属のｱｰﾑを取付ける",
"2. ②の内側ｹｰﾌﾞﾙｻﾎﾟｰﾄを固定する"
],
"WorkPoints": [
"X軸ｹｰﾌﾞﾙﾍﾞｱ外側",
"下図に示す部分をｹｰﾌﾞ... | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示された位置で結束が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾍﾞｱ取付け",
"WorkItems": [
"1. ①のY軸用ｹｰﾌﾞﾙﾍﾞｱをｾｯﾄする",
"3. ②の外側ｹｰﾌﾞﾙｻﾎﾟｰﾄの可動側を固定する",
"4. ②の外側ｹｰﾌﾞﾙｻﾎﾟｰﾄの固定側を固定する",
"5. 付属のｱｰﾑを取付ける",
"2. ②の内側ｹｰﾌﾞﾙｻﾎﾟｰﾄを固定する"
],
"WorkPoints": [
"Y軸ｹｰﾌﾞﾙﾍﾞｱ外側",
"下図に示す部分をｹｰﾌﾞ... | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示された位置で結束が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "外観確認",
"WorkItems": [
"1. ①の外観を確認する"
],
"WorkPoints": [
"CN6",
"1A22",
"黄色配管",
"黒色配管",
"CN1",
"XEM503",
"Y軸ﾍﾞｱ",
"X軸ﾍﾞｱ",
"XMM/EM503",
"4K303",
"白色配管",
"U/V/W/E2K503",
... | {
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管によじれが無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け(架台正面右下ｶﾊﾞｰ)",
"WorkItems": [
"1. COVER へLABEL LABEL LABEL LABEL を貼付ける",
"2. 1の完成品へLABEL を添付する"
],
"WorkPoints": [
"貼付けはし無い事 ※台紙のまま添付のみ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け(架台背面左下ｶﾊﾞｰ)",
"WorkItems": [
"1. COVER へLABEL LABEL を貼付ける",
"2. 1完成品の裏面にLABEL を貼付"
],
"WorkPoints": [
"ｵﾓﾃ",
"ｳﾗ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": []... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け(架台正面左下ｶﾊﾞｰ)",
"WorkItems": [
"1. COVER へLABEL LABEL を貼付ける"
],
"WorkPoints": [
"ｵﾓﾃ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"107mm"... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け(架台背面右下ｶﾊﾞｰ)",
"WorkItems": [
"1. COVER へLABEL LABEL を貼付ける"
],
"WorkPoints": [
"ｵﾓﾃ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"107mm"... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞｯｼｭ取付け【OP:ITF17連/ASF34連交換台車切替ﾕﾆｯﾄ】",
"WorkItems": [
"1. ①②にBUSH BUSH を取付ける"
],
"WorkPoints": [
"BUSH を先に取付ける",
"交換台車切替ﾕﾆｯﾄ(前側仕様時)",
"交換台車切替ﾕﾆｯﾄ(後側仕様時)",
"仕様により取付け作業を行う事",
"BUSH に当付けて取付ける"
],
"Tolks": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し(ﾒｲﾝｴｱｰﾊﾞﾙﾌﾞｶﾊﾞｰ)",
"WorkItems": [
"1. COVER をH2工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し(供給部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し(本体部)",
"WorkItems": [
"1. SCREW をH2工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し(付属品)",
"WorkItems": [
"1. BRACKET BRACKET BOLT CAP CASE Caution sheet (Maintenance) Nozzle Shaft Cleaning Tool(Silicon Type):FC GREASE COUPLER をH2工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Insp... | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立①",
"WorkItems": [
"▲1. PLATE にSPACER ･SPACER ･SPACER ･SPACER ･SPACER ･SPACER ･SPACER ･SPACER をSCREW ･SCREW で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立②",
"WorkItems": [
"1. ①に②･CABLE ･CABLE を⑯･⑰･⑱で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立①",
"WorkItems": [
"1. ①に②･③を圧入し④を組付け",
"2. ⑤に1.完成品を⑯･⑰で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"底面図"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立①",
"WorkItems": [
"1. ①に②･③を圧入し④を組付け",
"2. ⑤に1.完成品を⑯･⑰で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"底面図"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:9.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立②",
"WorkItems": [
"1. ①に②を⑯･⑰で組付け",
"2. 1.完成品に⑱･⑲を組付け"
],
"WorkPoints": [
"方向注意!!円の接線に平行に組付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立③",
"WorkItems": [
"1. ①に②を圧入",
"2. 1.完成品に③を挿入し④を⑯･⑰で組付け",
"3. ⑤に⑥を組付け",
"4. 2.完成品に3.完成品を⑱で組付け",
"1. ①に②を圧入",
"2. 1.完成品に③を挿入し④を⑯･⑰で組付け",
"3. ⑤に⑥を組付け",
"4. 2.完成品に3.完成品を⑱で組付け"
],
"WorkPoin... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代(合計8個):3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. ①にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"2. 1.完成品にPOST を挿入し④をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当て... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. ①にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"2. 1.完成品にPOST を挿入し④をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当て... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.2~1.5N･m",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. ①にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当てて組付け"
],
"To... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2~1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. ①にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"2. 1.完成品にPOST を挿入し④をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当て... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立⑤",
"WorkItems": [
"1. ①のｼｬﾌﾄに②･③･④を挿入し⑯･⑰で組付け"
],
"WorkPoints": [
"③は②を挿入後④を組付ける前に挿入",
"②はﾄﾞｸﾞとｽﾄｯﾊﾟｰの位置関係に注意して挿入すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立⑥",
"WorkItems": [
"1. ①に②を取付",
"2. 1.完成品に③を⑯･⑰･⑱で取付"
],
"WorkPoints": [
"ﾄﾞｸﾞの下側に通すこと",
"ﾎﾟｽﾄの穴にｾﾝｻの突起を挿し込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-089",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3.5㎜",
"ToolOther": "",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:3.5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.