input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "ｵｰﾄｽｲｯﾁ確認",
"WorkItems": [
"1. ①を㉖にセットし各電磁弁スイッチON/OFF数回繰り返しオートスイッチがONになることを確認する"
],
"WorkPoints": [
"5回程度､行戻動作をさせて各ｼﾘﾝﾀﾞ駆動のｵｰﾄｽｲｯﾁがONになることを確認する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C04... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "正常に動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "小型汎用表示器の設定",
"WorkItems": [
"1. 【FUNCTION】ｷｰを押しながら【HOLD】ｷｰを2秒間押し設定ﾛｯｸを解除する",
"2. 【TEDS】ｷｰを押しながら【SHIFT】ｷｰを長押しすると表示が『----』となり設定が完了する",
"3. 【SET】ｷｰを長押しして『F-01』を表示させ【→】ｷｰを2回押して『F-03』を表示させる｡ 【SET】ｷｰを押して表示される数値を確認し【CANCEL】ｷｰを2回押す",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "初期設定値の確認",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "小型汎用表示器の設定",
"WorkItems": [
"1. 【FUNCTION】ｷｰを押しながら【HOLD】ｷｰを2秒間押し設定ﾛｯｸを解除する",
"2. 【TEDS】ｷｰを押しながら【SHIFT】ｷｰを長押しすると表示が『----』となり設定が完了する",
"3. 【SET】ｷｰを長押しして『F-01』を表示させ【→】ｷｰを2回押して『F-03』を表示させる｡ 【SET】ｷｰを押して表示... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "正常に動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "小型汎用表示器の上限値・下限値設定と動作ﾊﾟﾀｰﾝ切替",
"WorkItems": [
"1. 設定前に｢STATUS｣の表示を確認し下記表にて設定値の確認を行う",
"3. 【→】ｷｰで変更したい桁に点滅を移動し【↑】ｷｰで数値を変更する 【SET】ｷｰを押すと上限値の設定が完了する",
"5. 【→】ｷｰで変更したい桁に点滅を移動し【↑】ｷｰで数値を変更する 【SET】ｷｰを押すと下限値の設定が完了する",
"2. 上限値の設定 ... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "小型汎用表示器の上限値・下限値設定と動作ﾊﾟﾀｰﾝ切替",
"WorkItems": [
"1. 設定前に｢STATUS｣の表示を確認し下記表にて設定値の確認を行う",
"3. 【→】ｷｰで変更したい桁に点滅を移動し【↑】ｷｰで数値を変更する 【SET】ｷｰを押すと上限値の設定が完了する",
"5. 【→】ｷｰで変更したい桁に点滅を移動し【↑】ｷｰで数値を変更する 【SET】ｷｰを押すと下限... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "正常に動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "小型汎用表示器のﾛｯｸ設定",
"WorkItems": [
"1. 【FUNCTION】ｷｰを押しながら【HOLD】ｷｰを2秒間押し設定ﾛｯｸを行う"
],
"WorkPoints": [
"作業完了後に実施することLED表示｢LOCK｣点灯を確認すること"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表①:ﾊｰﾄ... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "小型汎用表示器のﾛｯｸ設定",
"WorkItems": [
"1. 【FUNCTION】ｷｰを押しながら【HOLD】ｷｰを2秒間押し設定ﾛｯｸを行う"
],
"WorkPoints": [
"作業完了後に実施することLED表示｢LOCK｣点灯を確認すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ保持ﾌﾞﾛｯｸ",
"Size": "",
"ToolOther": "FM-4325",
"WorkName": "ｷｬﾘﾌﾞﾚｰｼｮﾝ",
"WorkItems": [
"1. ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄをｼﾞｸﾞﾌﾞﾛｯｸの上にｾｯﾄする"
],
"WorkPoints": [
"･下図の通り㉖を設置する",
"ﾏｲﾅｽにならないこと",
"ﾏｲﾅｽにならないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "設置確認",
"ToolManageNo": "FM-4325",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｰﾄﾞｾﾙ確認用分銅",
"Size": "",
"ToolOther": "FM-4273",
"WorkName": "ｷｬﾘﾌﾞﾚｰｼｮﾝ",
"WorkItems": [],
"WorkPoints": [
"ﾏｲﾅｽにならないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼﾞｸﾞﾌﾞﾛｯｸ②",
"x2個",
"ﾏｲﾅｽNG"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4273",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｷｬﾘﾌﾞﾚｰｼｮﾝ",
"WorkItems": [
"1. ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄをｼﾞｸﾞﾌﾞﾛｯｸの上にｾｯﾄする",
"2. ﾛｰﾄﾞｾﾙが無負荷状態で【CANCEL TEDS】ｷｰを2秒以上押す",
"3. ㉗をロードセルの中心に載せる",
"4. 【SET】ｷｰを2秒以上押し【→】ｷｰを押し表示を\"F-02\"にし【SET】を押す",
"5. 表示の\"50.00\"を【→】【↑】を押し\"00.96\"にして【... | {
"QualityItem": "出力確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "0.96N±25%以内",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "前ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"BRACKET は外側に押し当てて取付",
"BRACKET との干渉無き事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ｶﾊﾞｰ取付1/2",
"WorkItems": [
"1. ①にRUBBER を取付",
"2. 1完成品に②をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｶﾊﾞｰ取付2/2",
"WorkItems": [
"1. ①にPOST をBOLT WASHER WASHER (各2個)で取付"
],
"WorkPoints": [
"POST の取付方向に注意",
"POST の切り欠きと①取付部の切り欠きを合わせて取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ取付2/2",
"WorkItems": [
"1. ①にPOST をBOLT WASHER WASHER (各2個)で取付"
],
"WorkPoints": [
"POST の取付方向に注意",
"POST の切り欠きと①取付部の切り欠きを合わせて取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WEPJ-G002-C040",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "IO検査1",
"WorkItems": [
"1. ヘッドメンテナンスユニットを㉖にセットしエア配管を挿入",
"2. 各種電源をONする"
],
"WorkPoints": [
"ｴｱを接続",
"#3ｽﾛｯﾄに搭載する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "動作確認用制御BOX",
"Size": "",
"ToolOther": "FM-4367",
"WorkName": "IO検査1",
"WorkItems": [
"1. ヘッドメンテナンスユニットを㉖にセットしエア配管を挿入",
"2. 各種電源をONする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"動作確認用制御BOX",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "台車制御用電源BOX",
"Size": "",
"ToolOther": "FM-4368",
"WorkName": "IO検査1",
"WorkItems": [
"1. ヘッドメンテナンスユニットを㉖にセットしエア配管を挿入",
"2. 各種電源をONする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"動作確認用制御BOX",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4368",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "IO検査2",
"WorkItems": [
"1. \"BD init\"を押しﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄを認識したかﾓﾆﾀｰで確認する ｢Board Inti END｣確認後､\"接続(#3)\"を押し｢#3 接続 OK｣を確認する",
"2. \"次ﾍﾟｰｼﾞ\"を押し\"Pattern1\"を2回押して\"Pattern3\"にする"
],
"WorkPoints": [
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "動作確認用制御BOX",
"Size": "",
"ToolOther": "FM-4367",
"WorkName": "IO検査2",
"WorkItems": [
"1. \"BD init\"を押しﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄを認識したかﾓﾆﾀｰで確認する ｢Board Inti END｣確認後､\"接続(#3)\"を押し｢#3 接続 OK｣を確認する",
"2. \"次ﾍﾟｰｼﾞ\"を押し\"Pattern1\"を2回押して\"Pattern3\"にする"
],
"WorkPoints": [
"\"Board Ini... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "台車制御用電源BOX",
"Size": "",
"ToolOther": "FM-4368",
"WorkName": "IO検査2",
"WorkItems": [
"1. \"BD init\"を押しﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄを認識したかﾓﾆﾀｰで確認する ｢Board Inti END｣確認後､\"接続(#3)\"を押し｢#3 接続 OK｣を確認する",
"2. \"次ﾍﾟｰｼﾞ\"を押し\"Pattern1\"を2回押して\"Pattern3\"にする"
],
"WorkPoints": [
"\"Board Ini... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-4368",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "IO検査3",
"WorkItems": [
"1. \"Unit\"を確認して\"Start\"を押し本体部のﾛｯｸｼﾘﾝﾀﾞｰが上下しているか確認し (音とｾﾝｻｰON/OFF)\"Suspend\"で停止させる",
"2. \"Unit\"を押し\"Plate\"にして\"Resume\"を押しﾌﾟﾚｰﾄｼﾘﾝﾀﾞｰが上下しているか確認し\"Suspend\"を押し停止させる"
],
"... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "動作確認用制御BOX",
"Size": "",
"ToolOther": "FM-4367",
"WorkName": "IO検査3",
"WorkItems": [
"1. \"Unit\"を確認して\"Start\"を押し本体部のﾛｯｸｼﾘﾝﾀﾞｰが上下しているか確認し (音とｾﾝｻｰON/OFF)\"Suspend\"で停止させる",
"2. \"Unit\"を押し\"Plate\"にして\"Resume\"を押しﾌﾟﾚｰﾄｼﾘﾝﾀﾞｰが上下しているか確認し\"Suspend\"を押し停止させる"
],
"WorkPoints":... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "台車制御用電源BOX",
"Size": "",
"ToolOther": "FM-4368",
"WorkName": "IO検査3",
"WorkItems": [
"1. \"Unit\"を確認して\"Start\"を押し本体部のﾛｯｸｼﾘﾝﾀﾞｰが上下しているか確認し (音とｾﾝｻｰON/OFF)\"Suspend\"で停止させる",
"2. \"Unit\"を押し\"Plate\"にして\"Resume\"を押しﾌﾟﾚｰﾄｼﾘﾝﾀﾞｰが上下しているか確認し\"Suspend\"を押し停止させる"
],
"WorkPoints":... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4368",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "IO検査4",
"WorkItems": [
"2. \"Plate\"を押し\"Shutter\"にして\"Resume\"を押し､ｼｬｯﾀｰｼﾘﾝﾀﾞｰが前後しているか確認し､\"Suspend\"を押し停止させる"
],
"WorkPoints": [
"Plate⇒Shutterへ切替える事"
],
"Tolks": [],
"InspectionNo": "WEPJ-G... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "動作確認用制御BOX",
"Size": "",
"ToolOther": "FM-4367",
"WorkName": "IO検査4",
"WorkItems": [
"2. \"Plate\"を押し\"Shutter\"にして\"Resume\"を押し､ｼｬｯﾀｰｼﾘﾝﾀﾞｰが前後しているか確認し､\"Suspend\"を押し停止させる"
],
"WorkPoints": [
"Plate⇒Shutterへ切替える事"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A12",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "台車制御用電源BOX",
"Size": "",
"ToolOther": "FM-4368",
"WorkName": "IO検査4",
"WorkItems": [
"2. \"Plate\"を押し\"Shutter\"にして\"Resume\"を押し､ｼｬｯﾀｰｼﾘﾝﾀﾞｰが前後しているか確認し､\"Suspend\"を押し停止させる"
],
"WorkPoints": [
"Plate⇒Shutterへ切替える事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4368",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "16ﾉｽﾞﾙﾎﾙﾀﾞ",
"Size": "",
"ToolOther": "MTKP017641AB",
"WorkName": "IO検査4",
"WorkItems": [
"1. ﾉｽﾞﾙﾎﾙﾀﾞｰﾊﾟﾚｯﾄの①~⑧の箇所に16ﾉｽﾞﾙﾎﾙﾀﾞを搭載､□5~□8の箇所に8ﾉｽﾞﾙﾎﾙﾀﾞを搭載してｾｯﾄする"
],
"WorkPoints": [
"16ﾉｽﾞﾙﾎﾙﾀﾞ側",
"8ﾉｽﾞﾙﾎﾙﾀﾞ側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "8ﾉｽﾞﾙﾎﾙﾀﾞ",
"Size": "",
"ToolOther": "MTKP016632AD",
"WorkName": "IO検査4",
"WorkItems": [
"1. ﾉｽﾞﾙﾎﾙﾀﾞｰﾊﾟﾚｯﾄの①~⑧の箇所に16ﾉｽﾞﾙﾎﾙﾀﾞを搭載､□5~□8の箇所に8ﾉｽﾞﾙﾎﾙﾀﾞを搭載してｾｯﾄする"
],
"WorkPoints": [
"16ﾉｽﾞﾙﾎﾙﾀﾞ側",
"8ﾉｽﾞﾙﾎﾙﾀﾞ側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "IO検査5",
"WorkItems": [
"1. \"Shutter\"を押し\"Block\"にして\"Resume\"を押し清掃ﾌﾞﾛｯｸｼﾘﾝﾀﾞｰが上下しているか確認し\"Suspend\"を押し停止させる"
],
"WorkPoints": [
"Shutter⇒Blockへ切替える事"
],
"Tolks": [],
"InspectionNo": "WEPJ-G... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "動作確認用制御BOX",
"Size": "",
"ToolOther": "FM-4367",
"WorkName": "IO検査5",
"WorkItems": [
"1. \"Shutter\"を押し\"Block\"にして\"Resume\"を押し清掃ﾌﾞﾛｯｸｼﾘﾝﾀﾞｰが上下しているか確認し\"Suspend\"を押し停止させる"
],
"WorkPoints": [
"Shutter⇒Blockへ切替える事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "台車制御用電源BOX",
"Size": "",
"ToolOther": "FM-4368",
"WorkName": "IO検査5",
"WorkItems": [
"1. \"Shutter\"を押し\"Block\"にして\"Resume\"を押し清掃ﾌﾞﾛｯｸｼﾘﾝﾀﾞｰが上下しているか確認し\"Suspend\"を押し停止させる"
],
"WorkPoints": [
"Shutter⇒Blockへ切替える事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4368",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4294",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"2. \"前ﾍﾟｰｼﾞ\"を押し\"切断(#3)\"を押し停止させ全ての電源をｵﾌにする",
"1. \"Pattern3\"を押し\"Pattern2\"にして\"Count Clr\"を押し画面上のｶｳﾝﾄが \"0\"になっているか確認しｴｰｼﾞﾝｸﾞを開始させ終了時は\"Suspend\"を押す"
],
"WorkPoints": [... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "動作確認用制御BOX",
"Size": "",
"ToolOther": "FM-4367",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"2. \"前ﾍﾟｰｼﾞ\"を押し\"切断(#3)\"を押し停止させ全ての電源をｵﾌにする",
"1. \"Pattern3\"を押し\"Pattern2\"にして\"Count Clr\"を押し画面上のｶｳﾝﾄが \"0\"になっているか確認しｴｰｼﾞﾝｸﾞを開始させ終了時は\"Suspend\"を押す"
],
"WorkPoints": [
"連続動作で... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "台車制御用電源BOX",
"Size": "",
"ToolOther": "FM-4368",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"2. \"前ﾍﾟｰｼﾞ\"を押し\"切断(#3)\"を押し停止させ全ての電源をｵﾌにする",
"1. \"Pattern3\"を押し\"Pattern2\"にして\"Count Clr\"を押し画面上のｶｳﾝﾄが \"0\"になっているか確認しｴｰｼﾞﾝｸﾞを開始させ終了時は\"Suspend\"を押す"
],
"WorkPoints": [
"連続動作で... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4368",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"3. ｴｰｼﾞﾝｸﾞ終了後､ﾌﾟﾚｰﾄ高さを測定し規格内であることを確認する"
],
"WorkPoints": [
"規格から外れていたら､ﾌﾟﾚｰﾄ高さ調整をやり直す",
"規格値:測定箇所 各±0.02㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "測定箇所各±0.02㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-A12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "外観確認",
"WorkItems": [
"1. ①の本体からﾉｽﾞﾙﾎﾙﾀﾞｰﾊﾟﾚｯﾄを外す",
"3. ①の本体の外装を清掃する",
"2. 1.完成品の本体の外装に傷･汚れなどないか確認する"
],
"WorkPoints": [
"ﾉｽﾞﾙﾎﾙﾀﾞｰﾊﾟﾚｯﾄ",
"目視にて確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷､汚れ等が無いか確認する",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包1",
"WorkItems": [
"1. ①のﾉｽﾞﾙﾎﾙﾀﾞｰﾊﾟﾚｯﾄの取付部を梱包"
],
"WorkPoints": [
"梱包箇所",
"ｴｱﾏｯﾄを3つ折にして置く",
"ｶﾞﾑﾃｰﾌﾟでｴｱﾏｯﾄを固定する",
"ｶﾊﾞｰ開口部全体にｴｱﾏｯﾄを置き､ｶﾞﾑﾃｰﾌﾟで固定する"
],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包2",
"WorkItems": [
"1. ①のｴｱ供給部を梱包"
],
"WorkPoints": [
"ｴｱﾏｯﾄをｶﾌﾟﾗ部に巻きｶﾞﾑﾃｰﾌﾟで固定する",
"ｶﾞﾑﾃｰﾌﾟでｶﾌﾟﾗ部を外装に固定する",
"ﾁｭｰﾌﾞの余長をﾊﾝﾄﾞﾙに巻く事",
"梱包箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包3",
"WorkItems": [
"1. ①の全体を梱包"
],
"WorkPoints": [
"1枚のｴｱﾏｯﾄで全体を梱包する",
"ｴｱﾏｯﾄで全体を巻き､ｶﾞﾑﾃｰﾌﾟで下部を固定する",
"ｸﾗﾝﾊﾟｰ部も巻く事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wo... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包4",
"WorkItems": [
"2. FILTER FILTER FILTER FILTER を梱包する",
"1. ①を梱包する",
"3. 1.完成品と2.完成品をCASE に入れる",
"5. ビニール袋に㉗を貼付、㉗に品番を記入する",
"4. 3.完成品をﾋﾞﾆｰﾙ袋に入れる"
],
"WorkPoints": [
"ﾉｽﾞﾙﾌｫﾙﾀﾞｰﾊﾟﾚｯﾄ",
"ﾌｨﾙﾀｰ",
... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包5",
"WorkItems": [
"1. ①に②を固定する"
],
"WorkPoints": [
"ﾌｨﾙﾀｰ梱包箱",
"ﾉｽﾞﾙﾌｨﾙﾀｰﾊﾟﾚｯﾄ梱包箱"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包6",
"WorkItems": [
"1. CASE を組立てる",
"2. 1.完成品に底板を敷く",
"3. 2.完成品に側面ｽﾍﾟｰｻｰを入れる"
],
"WorkPoints": [
"CASE の底面をｶﾞﾑﾃｰﾌﾟで固定する",
"底板",
"底板の向きに注意して入れる事",
"原産国ｼｰﾙ貼付け面側",
"原産国ｼｰﾙ貼付け面側",
"切欠きを上にして入れる... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包7",
"WorkItems": [
"1. ①を②に入れる",
"2. ②の前後ｽﾍﾟｰｻｰを入れる"
],
"WorkPoints": [
"原産国ｼｰﾙ貼付け面側",
"ﾉｽﾞﾙﾎﾙﾀﾞｰﾊﾟﾚｯﾄ側",
"①と②の向きに注意して入れる事",
"ｽﾍﾟｰｻｰは2種類あるので注意",
"写真の様に配置して入れること",
"写真の様に配置して入れること",
"梱包物ﾁｪｯ... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包8",
"WorkItems": [
"1. ①に上面ｽﾍﾟｰｻｰ1を入れる",
"2. ①に上面ｽﾍﾟｰｻｰ2を入れる",
"3. ①の蓋を閉じる"
],
"WorkPoints": [
"凸部を下向きに入れる事",
"切欠き:大",
"切欠き:小",
"切欠き:大",
"切欠き:小",
"上面ｽﾍﾟｰｻｰ1",
"上面ｽﾍﾟｰｻｰ2"
],
"To... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体部梱包9",
"WorkItems": [
"1. ①にLABEL ③を貼付る",
"2. 1.完成品の表示の上にｶﾞﾑﾃｰﾌﾟを貼付る"
],
"WorkPoints": [
"①のﾗｲﾝに合わせて貼付る事",
"①のﾗｲﾝに合わせて貼付る事",
"側面の4ヶ所に貼付る事",
"30kgの表示の上にｶﾞﾑﾃｰﾌﾟを貼る",
"③は梱包したﾍｯﾄﾞﾒﾝﾃﾅﾝｽﾕﾆｯﾄと同じｼﾘｱﾙNoを貼付る事"
... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1各ﾓｰﾀSWの設定及び確認",
"WorkItems": [
"1. ﾚｰﾝ1固定側ﾓｰﾀｰのﾃﾞｨｯﾌﾟｽｲｯﾁを設定"
],
"WorkPoints": [
"ﾃﾞｨｯﾌﾟSW､ﾛｰﾀﾘｰSWの設定確認をする事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"InspectionItems": [
"検査表①:ﾓｰﾀﾃﾞｨｯﾌﾟSWの確認"
],
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2各ﾓｰﾀSWの設定及び確認",
"WorkItems": [
"1. ﾚｰﾝ2固定側ﾓｰﾀｰのﾃﾞｨｯﾌﾟｽｲｯﾁを設定"
],
"WorkPoints": [
"ﾃﾞｨｯﾌﾟSW､ﾛｰﾀﾘｰSWの設定確認をする事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"InspectionItems": [
"検査表①:ﾓｰﾀﾃﾞｨｯﾌﾟSWの確認"
],
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ接続確認",
"WorkItems": [
"1. 各ｺﾈｸﾀが検査書通りに接続されているか確認"
],
"WorkPoints": [
"ｺﾈｸﾀが接続されている事を目視で確認",
"ﾏｰｷﾝｸﾞﾀｲ､ﾏｰｸﾁｭｰﾌﾞにて名称を確認する事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｧｲﾊﾞｰ接続確認",
"WorkItems": [
"1. 各ﾌｧｲﾊﾞｰが検査書通りに接続されているか確認"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞﾀｲ､ﾏｰｸﾁｭｰﾌﾞにて名称を確認する事",
"奥まで挿入してあり､ﾛｯｸされている事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"InspectionItems": [
"検査表①:... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "ﾁｪｯｶｰ接続",
"WorkItems": [
"1. ﾁｪｯｶｰ治具を接続",
"2. ﾁｪｯｶｰ治具の電源をON",
"3. 仕様を選択しﾌﾟﾛｸﾞﾗﾑｽﾀｰﾄを押す",
"2. ﾁｪｯｶｰ治具の電源をON",
"3. 仕様を選択しﾌﾟﾛｸﾞﾗﾑｽﾀｰﾄを押す"
],
"WorkPoints": [
"各ｺﾈｸﾀ名称に合わせ接続する事",
"A⇒正流れ... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "基板検出ｾﾝｻｱﾝﾌﾟの設定",
"WorkItems": [
"1. ｱﾝﾌﾟの周期を検査書通りに設定"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP",
"ｽﾗｲﾄﾞ搬送OP",
"設定方法は検査書参照の事",
"逆流れ仕様時もｱﾝﾌﾟ設定は正流れ仕様時と同様"
],
"Tolks": [],
"InspectionNo": "",
"... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板検出ｾﾝｻｱﾝﾌﾟの設定",
"WorkItems": [
"1. ｱﾝﾌﾟの周期を検査書通りに設定"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP",
"ｽﾗｲﾄﾞ搬送OP",
"設定方法は検査書参照の事",
"逆流れ仕様時もｱﾝﾌﾟ設定は正流れ仕様時と同様"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"Inspection... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "ｱﾝﾌﾟﾃﾞｼﾞﾀﾙ表示反転設定",
"WorkItems": [
"1. ｱﾝﾌﾟ表示を反転させる"
],
"WorkPoints": [
"反転",
"橙枠の2個所",
"設定後 dISP ON に戻す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": []... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱﾝﾌﾟﾃﾞｼﾞﾀﾙ表示反転設定",
"WorkItems": [
"1. ｱﾝﾌﾟ表示を反転させる"
],
"WorkPoints": [
"反転",
"橙枠の2個所",
"設定後 dISP ON に戻す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "搬送ﾓｰﾀ動作確認",
"WorkItems": [
"1. 搬送ﾓｰﾀのｱﾄﾞﾚｽを確認",
"2. 搬送ﾓｰﾀの動作を確認",
"1. 搬送ﾓｰﾀのｱﾄﾞﾚｽを確認",
"2. 搬送ﾓｰﾀの動作を確認"
],
"WorkPoints": [
"F8 ENABLEを押しながら｢一括確認｣を押す",
"『OK』が表示される事を確認",
"回転している事を目視... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送ﾓｰﾀ動作確認",
"WorkItems": [
"1. 搬送ﾓｰﾀのｱﾄﾞﾚｽを確認",
"2. 搬送ﾓｰﾀの動作を確認"
],
"WorkPoints": [
"動作させているﾓｰﾀと､動作しているﾓｰﾀが合っている事を確認(回転方向も確認する事)",
"F8 ENABLEを押しながら｢一括確認｣を押す",
"F8 ENABLEを押しながら各ﾓｰﾀを押し動作させる",
"『OK』が表示される事を確認",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作している事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "ﾃﾞｭｱﾙﾓｰﾄﾞ幅寄せ動作確認",
"WorkItems": [
"1. ﾃﾞｭｱﾙﾓｰﾄﾞの搬送ﾚｰﾙ幅の確認"
],
"WorkPoints": [
"8ヶ所測定",
"ﾚｰﾝ1､ﾚｰﾝ2 共通 ･ﾃﾞｭｱﾙﾓｰﾄﾞ最大幅318.0~318.3㎜ 最小幅50.5~50.8㎜",
"F8 ENABLEを押しながら各幅のﾎﾞﾀﾝを押す"
],
"Tolks": [],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙﾓｰﾄﾞ幅寄せ動作確認",
"WorkItems": [
"1. ﾃﾞｭｱﾙﾓｰﾄﾞの搬送ﾚｰﾙ幅の確認"
],
"WorkPoints": [
"8ヶ所測定",
"ﾚｰﾝ1､ﾚｰﾝ2 共通 ･ﾃﾞｭｱﾙﾓｰﾄﾞ最大幅318.0~318.3㎜ 最小幅50.5~50.8㎜",
"F8 ENABLEを押しながら各幅のﾎﾞﾀﾝを押す"
],
"Tolks": [],
"InspectionNo":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "318.0㎜~318.3㎜50.5㎜~50.8㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "【OP】延長ｺﾝﾍﾞﾔｰﾃﾞｭｱﾙﾓｰﾄﾞ幅寄せ動作確認",
"WorkItems": [
"1. 延長ｺﾝﾍﾞﾔｰのﾃﾞｭｱﾙﾓｰﾄﾞ搬送ﾚｰﾙ幅の確認"
],
"WorkPoints": [
"4ヶ所測定",
"ﾚｰﾝ1､ﾚｰﾝ2 共通 ･ﾃﾞｭｱﾙﾓｰﾄﾞ最大幅318.0~318.3㎜ 最小幅50.5~50.8㎜",
"F8 ENABLEを押しながら各幅のﾎﾞﾀﾝを押す"
]... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "【OP】延長ｺﾝﾍﾞﾔｰﾃﾞｭｱﾙﾓｰﾄﾞ幅寄せ動作確認",
"WorkItems": [
"1. 延長ｺﾝﾍﾞﾔｰのﾃﾞｭｱﾙﾓｰﾄﾞ搬送ﾚｰﾙ幅の確認"
],
"WorkPoints": [
"4ヶ所測定",
"ﾚｰﾝ1､ﾚｰﾝ2 共通 ･ﾃﾞｭｱﾙﾓｰﾄﾞ最大幅318.0~318.3㎜ 最小幅50.5~50.8㎜",
"F8 ENABLEを押しながら各幅のﾎﾞﾀﾝを押す"
],
"Tolks": []... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "318.0㎜~318.3㎜50.5㎜~50.8㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WETE-G002-C07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "ｼﾝｸﾞﾙﾓｰﾄﾞ幅寄せ動作確認",
"WorkItems": [
"1. ｼﾝｸﾞﾙﾓｰﾄﾞの搬送ﾚｰﾙ幅の確認",
"2. ﾓｰﾄﾞを切り替える"
],
"WorkPoints": [
"ﾚｰﾝ1･ｼﾝｸﾞﾙﾓｰﾄﾞ最大幅591.5~591.8㎜ 最小幅50.5~50.8㎜",
"ﾚｰﾝ2が待機位置に移動後ｼﾝｸﾞﾙﾓｰﾄﾞに切り替わる",
"F8 ENABLEを押しながら... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙﾓｰﾄﾞ幅寄せ動作確認",
"WorkItems": [
"1. ｼﾝｸﾞﾙﾓｰﾄﾞの搬送ﾚｰﾙ幅の確認"
],
"WorkPoints": [
"ﾚｰﾝ1･ｼﾝｸﾞﾙﾓｰﾄﾞ最大幅591.5~591.8㎜ 最小幅50.5~50.8㎜",
"ﾚｰﾝ2が待機位置に移動後ｼﾝｸﾞﾙﾓｰﾄﾞに切り替わる",
"F8 ENABLEを押しながらﾚｰﾝ2幅寄せ【42.0㎜】を押す",
"F8 ENABLEを押し... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "591.5㎜~591.8㎜50.5㎜~50.8㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "【OP】延長ｺﾝﾍﾞﾔｰｼﾝｸﾞﾙﾓｰﾄﾞ幅寄せ確認",
"WorkItems": [
"2. ﾓｰﾄﾞを切り替える",
"1. ｼﾝｸﾞﾙﾓｰﾄﾞの搬送ﾚｰﾙ幅の確認"
],
"WorkPoints": [
"ﾚｰﾝ1･ｼﾝｸﾞﾙﾓｰﾄﾞ最大幅591.5~591.8㎜ 最小幅50.5~50.8㎜",
"ﾚｰﾝ2が待機位置に移動後ｼﾝｸﾞﾙﾓｰﾄﾞに切り替わる",
"F8 EN... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "【OP】延長ｺﾝﾍﾞﾔｰｼﾝｸﾞﾙﾓｰﾄﾞ幅寄せ確認",
"WorkItems": [
"2. ﾓｰﾄﾞを切り替える",
"1. ｼﾝｸﾞﾙﾓｰﾄﾞの搬送ﾚｰﾙ幅の確認"
],
"WorkPoints": [
"ﾚｰﾝ1･ｼﾝｸﾞﾙﾓｰﾄﾞ最大幅591.5~591.8㎜ 最小幅50.5~50.8㎜",
"ﾚｰﾝ2が待機位置に移動後ｼﾝｸﾞﾙﾓｰﾄﾞに切り替わる",
"F8 ENABLEを押しながらﾚｰﾝ2幅寄... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "591.5㎜~591.8㎜50.5㎜~50.8㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WETE-G002-C07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "自動動作確認①",
"WorkItems": [
"1. 幅寄せ動作させ､ｱﾝﾌﾟの閾値を確認",
"2. 基板検出ｾﾝｻの動作を確認",
"1. 幅寄せ動作させ､ｱﾝﾌﾟの閾値を確認",
"2. 基板検出ｾﾝｻの動作を確認"
],
"WorkPoints": [
"ﾚｰﾝ1→最大幅591㎜ﾚｰﾝ2→最大幅318㎜",
"閾値100以上",
"ﾚｰﾝ1→最大... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "搬送用ﾃｽﾄ基板(最小)",
"Size": "",
"ToolOther": "FM-2142",
"WorkName": "自動動作確認①",
"WorkItems": [
"1. 幅寄せ動作させ､ｱﾝﾌﾟの閾値を確認",
"2. 基板検出ｾﾝｻの動作を確認"
],
"WorkPoints": [
"ﾚｰﾝ1→最大幅591㎜ﾚｰﾝ2→最大幅318㎜",
"閾値100以上"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"InspectionIt... | {
"QualityItem": "搬送確認",
"ToolManageNo": "FM-2142",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出力ONする事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "自動動作確認①",
"WorkItems": [
"1. 幅寄せ動作させ､ｱﾝﾌﾟの閾値を確認",
"2. 基板検出ｾﾝｻの動作を確認"
],
"WorkPoints": [
"ｱﾝﾌﾟの閾値(緑色)を検査書に記入",
"F8 ENABLEを押しながら｢最小幅｣を押す※ﾚｰﾝ1､ﾚｰﾝ2同時に幅寄せが動作",
"ﾚｰﾝ1→最大幅591㎜ﾚｰﾝ2→最大幅318㎜",
"表示と遮光しているｾﾝｻが合っているか確認",... | {
"QualityItem": "ｾﾝｻ光量確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "閾値100以上",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "自動動作確認2",
"WorkItems": [
"1. 基板搬送確認を行う"
],
"WorkPoints": [
"F8 ENABLEを押しながら搬送確認するﾚｰﾝと基板ｻｲｽﾞを押す",
"ﾃﾞｭｱﾙﾓｰﾄﾞ用 最大幅 350×300×1.6基板 最小幅 50×50×0.3 基板",
"ｼﾝｸﾞﾙﾓｰﾄﾞ用 510×320×1.6基板",
"※各基板を10枚搬送しｴﾗｰ無... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "搬送用ﾃｽﾄ基板(最大)",
"Size": "",
"ToolOther": "FM-2712",
"WorkName": "自動動作確認2",
"WorkItems": [
"1. 基板搬送確認を行う"
],
"WorkPoints": [
"F8 ENABLEを押しながら搬送確認するﾚｰﾝと基板ｻｲｽﾞを押す",
"ﾃﾞｭｱﾙﾓｰﾄﾞ用 最大幅 350×300×1.6基板 最小幅 50×50×0.3 基板",
"ｼﾝｸﾞﾙﾓｰﾄﾞ用 510×320×1.6基板",
"※各基板を10枚搬送しｴﾗｰ無い事"
... | {
"QualityItem": "搬送確認",
"ToolManageNo": "FM-2712",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "基板を10枚搬送しｴﾗｰ無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "搬送用ﾃｽﾄ基板(最小)",
"Size": "",
"ToolOther": "FM-2142",
"WorkName": "自動動作確認2",
"WorkItems": [
"1. 基板搬送確認を行う"
],
"WorkPoints": [
"F8 ENABLEを押しながら搬送確認するﾚｰﾝと基板ｻｲｽﾞを押す",
"ﾃﾞｭｱﾙﾓｰﾄﾞ用 最大幅 350×300×1.6基板 最小幅 50×50×0.3 基板",
"ｼﾝｸﾞﾙﾓｰﾄﾞ用 510×320×1.6基板",
"※各基板を10枚搬送しｴﾗｰ無い事"
... | {
"QualityItem": "搬送確認",
"ToolManageNo": "FM-2142",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "基板を10枚搬送しｴﾗｰ無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "FM-3309搬送用基板(510×320)",
"Size": "",
"ToolOther": "FM-3309",
"WorkName": "自動動作確認2",
"WorkItems": [
"1. 基板搬送確認を行う"
],
"WorkPoints": [
"F8 ENABLEを押しながら搬送確認するﾚｰﾝと基板ｻｲｽﾞを押す",
"ﾃﾞｭｱﾙﾓｰﾄﾞ用 最大幅 350×300×1.6基板 最小幅 50×50×0.3 基板",
"ｼﾝｸﾞﾙﾓｰﾄﾞ用 510×320×1.6基板",
"※各基板を10枚搬送し... | {
"QualityItem": "搬送確認",
"ToolManageNo": "FM-3309",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "基板を10枚搬送しｴﾗｰ無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "自動動作確認③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｲﾝﾀｰﾛｯｸｾﾝｻｰ動作確認ﾋﾟﾝ",
"Size": "",
"ToolOther": "FM-3325",
"WorkName": "自動動作確認③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C04"
]
} | {
"QualityItem": "検出確認",
"ToolManageNo": "FM-3325",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "誤判定無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾙねじｸﾞﾘｰｽｱｯﾌﾟ",
"WorkItems": [
"◆1. 幅寄せﾎﾞｰﾙﾈｼﾞのｸﾞﾘｰｽｱｯﾌﾟを行なう"
],
"WorkPoints": [
"固定ﾚｰﾙから150㎜の位置でｸﾞﾘｰｽｱｯﾌﾟ(計4個所)を行い全域に渡りｽﾄﾛｰｸする事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"InspectionItems": [
"検査表①:幅寄せ... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所:各1ｼｮｯﾄ",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞを行う"
],
"WorkPoints": [
"ｴｰｼﾞﾝｸﾞﾓｰﾄﾞにて140ｻｲｸﾙ(8H)問題なく動作する事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C04",
"InspectionItems": [
"検査表①:ｴｰｼﾞﾝｸﾞ確認"
],... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "140ｻｲｸﾙ(8H)問題なく動作する事",
"Method": "目視",
"RecordMethod": "WETE-G002-C04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "下受けﾋﾟﾝ検出ｾﾝｻ配線",
"WorkItems": [
"1. ①の配線を引き回し､固定"
],
"WorkPoints": [
"ﾚｰﾝ1､ﾚｰﾝ2同様の作業を実施の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "各固定側ﾓｰﾀｰ配線取付",
"WorkItems": [
"1. ①にCABLE CABLE CABLE CABLE CABLE CABLE CABLE CABLE を引き回す"
],
"WorkPoints": [
"M610R",
"M612R",
"M614R",
"M616R",
"M620R",
"M622R",
"M624R",
"M626R",
"ﾓｰﾀｰ配... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "各可動側ﾓｰﾀｰ配線取付",
"WorkItems": [
"1. ①にCABLE CABLE CABLE CABLE CABLE CABLE CABLE CABLE を引き回す"
],
"WorkPoints": [
"M611R",
"M613R",
"M615R",
"M617R",
"M621R",
"M623R",
"M625R",
"M627R"
],
"To... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1ﾌｧｲﾊﾞｰｾﾝｻｰ前段取り",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻｰ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①",
"WorkItems": [
"2. 1完成品にBOLT WASHER を取付",
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"①黄色ﾏｰｷﾝｸﾞ位置",
"②黄色ﾏｰｷﾝｸﾞ位置",
"③④黄色ﾏｰｷﾝｸﾞ位置",
"余長を十分にとる"
],
"Tol... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①",
"WorkItems": [
"2. 1完成品にBOLT WASHER を取付",
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"②黄色ﾏｰｷﾝｸﾞ位置",
"③④黄色ﾏｰｷﾝｸﾞ位置"
],
"Tolks": [],
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②",
"WorkItems": [
"2. 1完成品にBOLT WASHER を取付",
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"余長を十分にとる事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②",
"WorkItems": [
"2. 1完成品にBOLT WASHER を取付",
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"余長を十分にとる事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し③",
"WorkItems": [
"1. ①にﾌｧｲﾊﾞｰｾﾝｻｰを引き回す"
],
"WorkPoints": [
"左側",
"右側",
"L2側",
"L1側",
"Rを保ち､ﾎﾞﾙﾄ･厚肉ﾜｯｼｬｰを回避する事",
"Rを保ち､ﾎﾞﾙﾄ･厚肉ﾜｯｼｬｰを回避する事"
],
"Tolks": [],
"InspectionNo": ""... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し③",
"WorkItems": [
"1. ①にﾌｧｲﾊﾞｰｾﾝｻｰを引き回す"
],
"WorkPoints": [
"左側",
"右側",
"L2側",
"L1側",
"Rを保ち､ﾎﾞﾙﾄ･厚肉ﾜｯｼｬｰを回避する事",
"Rを保ち､ﾎﾞﾙﾄ･厚肉ﾜｯｼｬｰを回避する事"
],
"Tolks": [],
"InspectionNo": ""... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【選択仕様:逆流れ】ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"L1側",
"L2側",
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事"
],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP:ｽﾗｲﾄﾞ搬送仕様】ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"L1側",
"L2側",
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP:延長ｺﾝﾍﾞﾔｰ仕様】ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"L2側も同様の作業を行う事",
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "【OP:延長ｺﾝﾍﾞﾔｰ仕様】ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"L2側も同様の作業を行う事",
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP:260㎜仕様】ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"L2側も同様の作業を行う事",
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚｰﾝ1固定側ﾀﾞｸﾄ取付",
"WorkItems": [],
"WorkPoints": [
"ﾚｰﾙに対して､まっすぐ取付の事",
"配線の挟み込み注意",
"配線の挟み込み注意"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾚｰﾝ1固定側ﾀﾞｸﾄ取付",
"WorkItems": [
"2. 1完成品にDUCT をBOLT WASHER で取付",
"1. ①にDUCT をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1可動側配管引き回し",
"WorkItems": [
"1. ①にTUBE を引き回し､接続"
],
"WorkPoints": [
"しっかり奥まで差込む事",
"しっかり奥まで差込む事",
"1020㎜",
"2090㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾚｰﾝ1可動側ﾌｧｲﾊﾞｰｾﾝｻ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①",
"WorkItems": [
"2. 1完成品にBOLT WASHER を取付",
"1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚｰﾝ1可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①",
"WorkItems": [
"2. 1完成品にBOLT WASHER を取付",
"1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkT... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②",
"WorkItems": [
"2. 1完成品にBOLT WASHER を取付",
"1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"Inspectio... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚｰﾝ1可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②",
"WorkItems": [
"2. 1完成品にBOLT WASHER を取付",
"1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【選択仕様:逆流れ】ﾚｰﾝ1可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.